FSC 9310                                                         JCP K30
                         CREAM WHITE 100% INDEX
Index Paper                                             February 1, 1999

Use information: This paragraph is informational only and is not 
    exclusively definitive of the end use.
  For highest quality face and back offset printing of card indexes, 
identification cards, office forms, etc., requiring execution with pen 
and ink, erasing quality, and permanence. Printed matter may include 
text, line illustrations, halftones, and solid reverses.
Stock: 100 pct cotton or linen fibers.
    No fluorescent (optical) brighteners shall be added to the pulp or 
  paper during manufacture. Fluorescence, due to residual white water, 
  broke, or natural fibers, is permissible; provided the increase in 
  reflectance, measured with and without the ultraviolet component of a 
  light source of 3100 kelvin in combination with a C.I.E. 
  (International Commission on Illumination) Z (blue) filter, does not 
  exceed 2.0 pct.
    Note: \1\ Postconsumer recovered fiber, in any percentage, is 
  encouraged, provided that the requirements of this Standard are met.
Acidity: pH value shall average not less than 6.5.

Grammage (g/m \2\)................................ 225
  Basis weight: 25\1/2\ by 30\1/2\ inches, 500 
  (pounds)........................................ 125
  A tolerance of 10 pct shall be 

Bursting strength: Average, not less than (kPa)... 690
  Equivalent (lb/in2).................. 100

Thickness: Average (mm)........................... 0.255
  Equivalent (inch)............................... 0.010
    A tolerance of 0.013 mm (0.0005 inch) shall be allowed. 
  Paper shall be uniform and shall not vary more than 0.011 mm (0.0004 
  inch) from one edge to the other.

Ruling and writing qualities: Lines ruled and characters written with 
  pen and ink shall be clear cut and free from excessive feathering.
Erasing quality: Paper shall retain good ruling, writing and typing 
  quality, texture, and surface appearance, without ink spreading after 
  repeated erasures. Samples from the delivery shall show no greater 
  resistance than the standard sample to removal by abrasion of 
  typewritten characters.
General appearance: Paper shall conform to the standard sample(s) 
  adopted by the Government.
  Color: The paper in the order (or publication) shall be uniform with a 
  target brightness of 60 pct or as specified. The color variation shall 
  not exceed DE(CIELAB)=1.0.
  Finish and formation: Shall be uniform.
  Cleanliness: The dirt count for each side of the paper shall not 
  exceed 250 specks per square meter. No sample sheet (600 to 650 cm\2\ 
  in size) shall contain more than one defect with an equivalent area of 
  0.25 mm\2\ or greater.
Sampling and testing: Shall be conducted in accordance with standards in 
  Part 2, Government Paper Specification Standards.


 Unless otherwise specified, the following is automatically waived when 
  printing or duplicating is to be accomplished on commercial contract
Sizing: Paper shall be surface-sized with high-grade animal glue and 
  internal-sized suitable for satisfactory printing on both sides of the 
  sheet on high-speed offset presses equipped with continuous flow or 
  brush dampening systems.

Color: Shall match the Government's standard sample for color. A 
  deviation of DE(CIELAB)=3.0 from the color standard is allowed.
Curl: Paper shall lie flat with either no tendency to curl or with a 
  curl which can be overcome under reasonable working conditions.

Surface: Shall be free from lint, fuzz, or any particles which will 
  pick, lift, fluff, or pile on the blanket under normal press 
Size and trim: Sheets: Paper shall be furnished in the size(s) ordered 
  and shall be flat, trimmed square on four sides with clean smooth 
  edges, and evenly jogged. A tolerance of 2 mm (\1/16\ 
  inch) shall be allowed except for sheets 216 by 356 mm (8\1/2\ by 14 
  inches) or less; then a tolerance of 1 mm (\1/32\ inch) 
  shall be allowed. Successive sheets within any package shall not 
  differ from each other by more than 0.5 mm (\1/64\ inch). Paper with 
  the long dimension 813 mm (32 inches) or less shall be considered 
  square if the variation does not exceed 1 mm (\1/32\ inch); over 
  813 mm (32 inches), 2 mm (\1/16\ inch).
Grain: Direction of the grain on flat paper shall be as ordered.
Mill inspection: The use of this paper requires the highest degree of 
  accuracy in printing and binding operations. The manufacturer shall 
  inspect the paper to eliminate all waste, scrap, and paper with torn 
  sheets, turned corners, slime spots, dirt, and other foreign matter 
  which will detract from the appearance of the paper.
Pressroom conditions: The bulk of this paper will be used in air-
  conditioned pressrooms maintained at 24  deg.C 2  deg.C 
  and 45 pct 8 pct relative humidity.


    \1\ This grade is typically a low Government usage paper and 
currently not readily and/or economically available with postconsumer 
recovered fiber content. If a postconsumer recovered fiber content is 
desired in the paper, that number will be stated in the procurement 
document. Note, recovered material (cotton/linen) is not a postconsumer 
recovered fiber.