[Title 49 CFR ]
[Code of Federal Regulations (annual edition) - October 1, 2001 Edition]
[From the U.S. Government Printing Office]
[[Page i]]
49
Parts 100 to 185
Revised as of October 1, 2001
Transportation
Containing a codification of documents of general
applicability and future effect
As of October 1, 2001
With Ancillaries
Published by
Office of the Federal Register
National Archives and Records
Administration
A Special Edition of the Federal Register
[[Page ii]]
U.S. GOVERNMENT PRINTING OFFICE
WASHINGTON : 2001
For sale by the Superintendent of Documents, U.S. Government Printing
Office
Internet: bookstore.gpo.gov Phone: toll free (866) 512-1800; DC area
(202) 512-1800
Fax: (202) 512-2250 Mail: Stop SSOP, Washington, DC 20402-0001
[[Page iii]]
Table of Contents
Page
Explanation................................................. v
Title 49:
Subtitle B--Other Regulations Relating to Transportation:
Chapter I--Research and Special Programs
Administration, Department of Transportation 5
Finding Aids:
Material Approved for Incorporation by Reference........ 1061
Table of CFR Titles and Chapters........................ 1071
Alphabetical List of Agencies Appearing in the CFR...... 1089
List of CFR Sections Affected........................... 1099
[[Page iv]]
----------------------------
Cite this Code: CFR
To cite the regulations in
this volume use title,
part and section number.
Thus, 49 CFR 106.1 refers
to title 49, part 106,
section 1.
----------------------------
[[Page v]]
EXPLANATION
The Code of Federal Regulations is a codification of the general and
permanent rules published in the Federal Register by the Executive
departments and agencies of the Federal Government. The Code is divided
into 50 titles which represent broad areas subject to Federal
regulation. Each title is divided into chapters which usually bear the
name of the issuing agency. Each chapter is further subdivided into
parts covering specific regulatory areas.
Each volume of the Code is revised at least once each calendar year
and issued on a quarterly basis approximately as follows:
Title 1 through Title 16.................................as of January 1
Title 17 through Title 27..................................as of April 1
Title 28 through Title 41...................................as of July 1
Title 42 through Title 50................................as of October 1
The appropriate revision date is printed on the cover of each
volume.
LEGAL STATUS
The contents of the Federal Register are required to be judicially
noticed (44 U.S.C. 1507). The Code of Federal Regulations is prima facie
evidence of the text of the original documents (44 U.S.C. 1510).
HOW TO USE THE CODE OF FEDERAL REGULATIONS
The Code of Federal Regulations is kept up to date by the individual
issues of the Federal Register. These two publications must be used
together to determine the latest version of any given rule.
To determine whether a Code volume has been amended since its
revision date (in this case, October 1, 2001), consult the ``List of CFR
Sections Affected (LSA),'' which is issued monthly, and the ``Cumulative
List of Parts Affected,'' which appears in the Reader Aids section of
the daily Federal Register. These two lists will identify the Federal
Register page number of the latest amendment of any given rule.
EFFECTIVE AND EXPIRATION DATES
Each volume of the Code contains amendments published in the Federal
Register since the last revision of that volume of the Code. Source
citations for the regulations are referred to by volume number and page
number of the Federal Register and date of publication. Publication
dates and effective dates are usually not the same and care must be
exercised by the user in determining the actual effective date. In
instances where the effective date is beyond the cut-off date for the
Code a note has been inserted to reflect the future effective date. In
those instances where a regulation published in the Federal Register
states a date certain for expiration, an appropriate note will be
inserted following the text.
OMB CONTROL NUMBERS
The Paperwork Reduction Act of 1980 (Pub. L. 96-511) requires
Federal agencies to display an OMB control number with their information
collection request.
[[Page vi]]
Many agencies have begun publishing numerous OMB control numbers as
amendments to existing regulations in the CFR. These OMB numbers are
placed as close as possible to the applicable recordkeeping or reporting
requirements.
OBSOLETE PROVISIONS
Provisions that become obsolete before the revision date stated on
the cover of each volume are not carried. Code users may find the text
of provisions in effect on a given date in the past by using the
appropriate numerical list of sections affected. For the period before
January 1, 1986, consult either the List of CFR Sections Affected, 1949-
1963, 1964-1972, or 1973-1985, published in seven separate volumes. For
the period beginning January 1, 1986, a ``List of CFR Sections
Affected'' is published at the end of each CFR volume.
INCORPORATION BY REFERENCE
What is incorporation by reference? Incorporation by reference was
established by statute and allows Federal agencies to meet the
requirement to publish regulations in the Federal Register by referring
to materials already published elsewhere. For an incorporation to be
valid, the Director of the Federal Register must approve it. The legal
effect of incorporation by reference is that the material is treated as
if it were published in full in the Federal Register (5 U.S.C. 552(a)).
This material, like any other properly issued regulation, has the force
of law.
What is a proper incorporation by reference? The Director of the
Federal Register will approve an incorporation by reference only when
the requirements of 1 CFR part 51 are met. Some of the elements on which
approval is based are:
(a) The incorporation will substantially reduce the volume of
material published in the Federal Register.
(b) The matter incorporated is in fact available to the extent
necessary to afford fairness and uniformity in the administrative
process.
(c) The incorporating document is drafted and submitted for
publication in accordance with 1 CFR part 51.
Properly approved incorporations by reference in this volume are
listed in the Finding Aids at the end of this volume.
What if the material incorporated by reference cannot be found? If
you have any problem locating or obtaining a copy of material listed in
the Finding Aids of this volume as an approved incorporation by
reference, please contact the agency that issued the regulation
containing that incorporation. If, after contacting the agency, you find
the material is not available, please notify the Director of the Federal
Register, National Archives and Records Administration, Washington DC
20408, or call (202) 523-4534.
CFR INDEXES AND TABULAR GUIDES
A subject index to the Code of Federal Regulations is contained in a
separate volume, revised annually as of January 1, entitled CFR Index
and Finding Aids. This volume contains the Parallel Table of Statutory
Authorities and Agency Rules (Table I). A list of CFR titles, chapters,
and parts and an alphabetical list of agencies publishing in the CFR are
also included in this volume.
An index to the text of ``Title 3--The President'' is carried within
that volume.
The Federal Register Index is issued monthly in cumulative form.
This index is based on a consolidation of the ``Contents'' entries in
the daily Federal Register.
A List of CFR Sections Affected (LSA) is published monthly, keyed to
the revision dates of the 50 CFR titles.
[[Page vii]]
REPUBLICATION OF MATERIAL
There are no restrictions on the republication of material appearing
in the Code of Federal Regulations.
INQUIRIES
For a legal interpretation or explanation of any regulation in this
volume, contact the issuing agency. The issuing agency's name appears at
the top of odd-numbered pages.
For inquiries concerning CFR reference assistance, call 202-523-5227
or write to the Director, Office of the Federal Register, National
Archives and Records Administration, Washington, DC 20408 or e-mail
info@fedreg.nara.gov.
SALES
The Government Printing Office (GPO) processes all sales and
distribution of the CFR. For payment by credit card, call 202-512-1800,
M-F, 8 a.m. to 4 p.m. e.s.t. or fax your order to 202-512-2250, 24 hours
a day. For payment by check, write to the Superintendent of Documents,
Attn: New Orders, P.O. Box 371954, Pittsburgh, PA 15250-7954. For GPO
Customer Service call 202-512-1803.
ELECTRONIC SERVICES
The full text of the Code of Federal Regulations, The United States
Government Manual, the Federal Register, Public Laws, Public Papers,
Weekly Compilation of Presidential Documents and the Privacy Act
Compilation are available in electronic format at www.access.gpo.gov/
nara (``GPO Access''). For more information, contact Electronic
Information Dissemination Services, U.S. Government Printing Office.
Phone 202-512-1530, or 888-293-6498 (toll-free). E-mail,
gpoaccess@gpo.gov.
The Office of the Federal Register also offers a free service on the
National Archives and Records Administration's (NARA) World Wide Web
site for public law numbers, Federal Register finding aids, and related
information. Connect to NARA's web site at www.nara.gov/fedreg. The NARA
site also contains links to GPO Access.
Raymond A. Mosley,
Director,
Office of the Federal Register.
October 1, 2001.
[[Page ix]]
THIS TITLE
Title 49--Transportation is composed of seven volumes. The parts in
these volumes are arranged in the following order: Parts 1-99, parts
100-185, parts 186-199, parts 200-399, parts 400-999, parts 1000-1199,
part 1200 to End. The first volume (parts 1-99) contains current
regulations issued under subtitle A--Office of the Secretary of
Transportation; the second volume (parts 100-185) and the third volume
(parts 186-199) contain the current regulations issued under chapter I--
Research and Special Programs Administration (DOT); the fourth volume
(parts 200-399) contains the current regulations issued under chapter
II--Federal Railroad Administration (DOT), and chapter III--Federal
Motor Carrier Safety Administration (DOT); the fifth volume (parts 400-
999) contains the current regulations issued under chapter IV--Coast
Guard (DOT), chapter V--National Highway Traffic Safety Administration
(DOT), chapter VI--Federal Transit Administration (DOT), chapter VII--
National Railroad Passenger Corporation (AMTRAK), and chapter VIII--
National Transportation Safety Board; the sixth volume (parts 1000-1199)
contains the current regulations issued under chapter X--Surface
Transportation Board and the seventh volume (part 1200 to End) contains
the current regulations issued under chapter X--Surface Transportation
Board and chapter XI--Bureau of Transportation Statistics, Department of
Transportation. The contents of these volumes represent all current
regulations codified under this title of the CFR as of October 1, 2001.
In the volume containing parts 100-185, see Sec. 172.101 for the
Hazardous Materials Table, and Sec. 172.102 for the Optional Hazardous
Materials Table. The Federal Motor Vehicle Safety Standards appear in
part 571.
Redesignation tables for chapter X--Surface Transportation Board,
Department of Transportation appear in the Finding Aids section of the
sixth and seventh volumes.
[[Page x]]
[[Page 1]]
TITLE 49--TRANSPORTATION
(This book contains parts 100 to 185)
--------------------------------------------------------------------
SUBTITLE B--Other Regulations Relating To Transportation:
Part
chapter i--Research and Special Programs Administration,
Department of Transportation.............................. 106
[[Page 3]]
Subtitle B--Other Regulations Relating to Transportation
[[Page 5]]
CHAPTER I--RESEARCH AND SPECIAL PROGRAMS ADMINISTRATION, DEPARTMENT OF
TRANSPORTATION
--------------------------------------------------------------------
SUBCHAPTER A--HAZARDOUS MATERIALS AND OIL TRANSPORTATION
Part Page
106 Rulemaking procedures....................... 7
107 Hazardous materials program procedures...... 12
110 Hazardous materials public sector training
and planning grants..................... 53
SUBCHAPTER B--OIL TRANSPORTATION
130 Oil spill prevention and response plans..... 62
SUBCHAPTER C--HAZARDOUS MATERIALS REGULATIONS
171 General information, regulations, and
definitions............................. 65
172 Hazardous materials table, special
provisions, hazardous materials
communications, emergency response
information, and training requirements.. 97
173 Shippers--general requirements for shipments
and packagings.......................... 385
174 Carriage by rail............................ 626
175 Carriage by aircraft........................ 649
176 Carriage by vessel.......................... 668
177 Carriage by public highway.................. 724
178 Specifications for packagings............... 746
179 Specifications for tank cars................ 968
180 Continuing qualification and maintenance of
packagings.............................. 1024
[[Page 7]]
SUBCHAPTER A--HAZARDOUS MATERIALS AND OIL TRANSPORTATION
PART 106--RULEMAKING PROCEDURES--Table of Contents
Subpart A--General
Sec.
106.1 Scope.
106.3 Delegations.
106.5 Regulatory dockets.
106.7 Records.
106.9 Where to file petitions.
Subpart B--Procedures for Adoption of Rules
106.11 General.
106.13 Initiation of rulemaking.
106.15 Contents of notices of proposed rulemaking.
106.17 Participation by interested persons.
106.19 Petitions for extension of time to comment.
106.21 Contents of written comments.
106.23 Consideration of comments received.
106.25 Additional rulemaking proceedings.
106.27 Hearings.
106.29 Adoption of final rules.
106.31 Petitions for rulemaking.
106.33 Processing of petition.
106.35 Petitions for reconsideration.
106.37 Proceedings on petitions for reconsideration.
106.38 Appeals.
106.39 Direct final rulemaking.
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
Source: 40 FR 31768, July 29, 1975, unless otherwise noted.
Redesignated by Amdt. 102-1, and Amdt. 106-1, 43 FR 43306, Sept. 25,
1978.
Subpart A--General
Sec. 106.1 Scope.
This part prescribes general rulemaking procedures for the issue,
amendment, and repeal of Hazardous Material Safety Program regulations
of the Research and Special Programs Administration of the Department of
Transportation.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-13, 61 FR 51336,
Oct. 1, 1996]
Sec. 106.3 Delegations.
For the purposes of this part, ``Administrator'' means the
Administrator, Research and Special Programs Administration, or his or
her delegate.
[Amdt. 106-13, 61 FR 51336, Oct. 1, 1996]
Sec. 106.5 Regulatory dockets.
(a) Information and data considered relevant by the Administrator
relating to rulemaking actions, including notices of proposed
rulemaking; comments received in response to notices; petitions for
rulemaking and reconsideration; denials of petitions for rulemaking and
reconsideration; records of additional rulemaking proceedings under
Sec. 106.25; and final regulations are maintained by the Research and
Special Programs Administration at 400 7th Street, SW., Washington, DC
20590-0001.
(b) Any person may examine any docketed material at the offices of
the Research and Special Programs Administration at any time during
regular business hours after the docket is established, except material
which the Administrator determines should be withheld from public
disclosure under applicable provisions of any statute administered by
the Administrator and Section 552(b) of title 5, United States Code, and
may obtain a copy of it upon payment of a fee.
[40 FR 31768, July 29, 1975. Redesignated by Amdts. 102-1 and 106-1, 43
FR 43306, Sept. 25, 1978, and amended by Amdt. 106-3, 45 FR 81571, Dec.
11, 1980; Amdt. 106-7, 55 FR 39978, Oct. 1, 1990]
Sec. 106.7 Records.
Records of the Research and Special Programs Administration relating
to rulemaking proceedings are available for inspection as provided in
section 552(b) of title 5, United States Code, and part 7 of the
Regulations of the Office of the Secretary of Transportation (part 7 of
this title).
Sec. 106.9 Where to file petitions.
Petitions for extension of time to comment submitted under
Sec. 106.19, petitions for hearings submitted under Sec. 106.27,
petitions for rulemaking submitted under Sec. 106.31, and petitions for
[[Page 8]]
reconsideration submitted under Sec. 106.35 must be submitted to:
Administrator, Research and Special Programs Administration, U.S.
Department of Transportation, 400 7th Street, SW., Washington, DC 20590-
0001.
[40 FR 31768, July 29, 1975. Redesignated by Amdts. 102-1 and 106-1, 43
FR 43306, Sept. 25, 1978, and amended by Amdt. 106-3, 45 FR 81571, Dec.
11, 1980; Amdt. 106-7, 55 FR 39978, Oct. 1, 1990]
Subpart B--Procedures for Adoption of Rules
Sec. 106.11 General.
Unless the Administrator, for good cause, finds that notice is
impracticable, unnecessary, or contrary to the public interest, and
incorporates that finding and a brief statement of the reasons for it in
the rule, a notice of proposed rulemaking is issued and interested
persons are invited to participate in the rulemaking proceedings with
respect to each substantive rule.
Sec. 106.13 Initiation of rulemaking.
The Administrator initiates rulemaking on his or her own motion;
however, in so doing, the Administrator may use discretion to consider
the recommendations of other agencies of the United States or of other
interested persons, including those of any technical advisory body
established by statute for that purpose.
[Amdt. 106-13, 61 FR 51336, Oct. 1, 1996]
Sec. 106.15 Contents of notices of proposed rulemaking.
(a) Each notice of proposed rulemaking is published in the Federal
Register, unless all persons subject to it are named and are personally
served with a copy of it.
(b) Each notice, whether published in the Federal Register or
personally served, includes:
(1) A statement of the time, place, and nature of the proposed
rulemaking proceeding;
(2) A reference to the authority under which it is issued;
(3) A description of the subjects and issues involved or the
substance and terms of the proposed regulation;
(4) A statement of the time within which written comments must be
submitted; and
(5) A statement of how and to what extent interested persons may
participate in the proceeding.
Sec. 106.17 Participation by interested persons.
(a) Any interested person may participate in rulemaking proceedings
by submitting comments in writing containing information, views or
arguments in accordance with instructions for participation in the
rulemaking document.
(b) The Administrator may invite any interested person to
participate in the rulemaking proceedings described in Sec. 106.25.
(c) For the purposes of this part, an interested person includes any
Federal or State government agency or any political subdivision of a
State (as defined in Sec. 107.201(b) of this subchapter).
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, and amended by Amdt. 106-4, 48 FR 2651,
Jan. 20, 1983; Amdt. 106-11, 61 FR 30180, June 14, 1996; Amdt. 106-13,
61 FR 51336, Oct. 1, 1996]
Sec. 106.19 Petitions for extension of time to comment.
A petition for extension of the time to submit comments must be
received not later than 10 days before expiration of the time stated in
the notice. It is requested, but not required, that three copies be
submitted. The filing of the petition does not automatically extend the
time for petitioner's comments. A petition is granted only if the
petitioner shows good cause for the extension, and if the extension is
consistent with the public interest. If an extension is granted, it is
granted to all persons, and it is published in the Federal Register.
Sec. 106.21 Contents of written comments.
All written comments must be in English. It is requested, but not
required, that five copies be submitted. Any interested person should
submit as part of written comments all material considered relevant to
any statement of fact. Incorporation of material by reference should be
avoided; however,
[[Page 9]]
where necessary, such incorporated material shall be identified by
document title and page.
[Amdt. 106-13, 61 FR 51336, Oct. 1, 1996]
Sec. 106.23 Consideration of comments received.
All timely comments and the recommendations of any technical
advisory body established by statute for the purpose of reviewing the
proposed rule concerned are considered before final action is taken on a
rulemaking proposal. Late filed comments are considered so far as
practicable.
Sec. 106.25 Additional rulemaking proceedings.
The Administrator may initiate any further rulemaking proceedings
that the Administrator finds necessary or desirable. For example,
interested persons may be invited to make oral arguments, to participate
in conferences between the Administrator or the Administrator's
representative and interested persons at which minutes of the conference
are kept, to appear at informal hearings presided over by officials
designated by the Administrator at which a transcript of minutes are
kept, or participate in any other proceeding to assure informed
administrative action and to protect the public interest.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-13, 61 FR 51336,
Oct. 1, 1996]
Sec. 106.27 Hearings.
(a) If a notice of proposed rulemaking does not provide for a
hearing, any interested person may petition the Administrator for an
informal hearing. The petition must be received by the Administrator not
later than 20 days before expiration of the time stated in the notice.
The filing of the petition does not automatically result in the
scheduling of a hearing. A petition is granted only if the petitioner
shows good cause for a hearing. If a petition for a hearing is granted,
notice of the hearing is published in the Federal Register.
(b) Sections 556 and 557 of title 5, United States Code, do not
apply to hearings held under this part. Unless otherwise specified,
hearings held under this part are informal, nonadversary, fact-finding
proceedings, at which there are not formal pleadings or adverse parties.
Any regulation issued in a case in which an informal hearing is held is
not necessarily based exclusively on the record of the hearing.
(c) The Administrator designates a representative to conduct any
hearing held under this part. The Chief Counsel designates a member of
his or her staff to serve as legal officer at the hearing.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-13, 61 FR 51336,
Oct. 1, 1996]
Sec. 106.29 Adoption of final rules.
Final rules are prepared by representatives of the Office of
Hazardous Materials Safety concerned and the Office of the Chief
Counsel. The regulation is then submitted to the Administrator for
consideration. If the Administrator adopts the regulation, it is
published in the Federal Register, unless all persons subject to it are
named and are personally served with a copy of it.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-13, 61 FR 51336,
Oct. 1, 1996]
Sec. 106.31 Petitions for rulemaking.
(a) Any interested person may petition the Associate Administrator
for Hazardous Materials Safety to establish, amend, or repeal a
substantive regulation, or may petition the Chief Counsel to establish,
amend, or repeal a procedural regulation in parts 106 or 107.
(b) Each petition filed under this section must--
(1) Summarize the proposed action and explain its purpose;
(2) State the text of the proposed rule or amendment, or specify the
rule proposed to be repealed;
(3) Explain the petitioner's interest in the proposed action and the
interest of any party the petitioner represents; and
(4) Provide information and arguments that support the proposed
action, including relevant technical, scientific or other data as
available to the petitioner, and any specific known
[[Page 10]]
cases that illustrate the need for the proposed action.
(c) If the potential impact of the proposed action is substantial,
and information and data related to that impact are available to the
petitioner, the Associate Administrator for Hazardous Materials Safety
or the Chief Counsel may request the petitioner to provide--
(1) The costs and benefits to society and identifiable groups within
society, quantifiable and otherwise;
(2) The direct effects (including preemption effects) of the
proposed action on States, on the relationship between the Federal
Government and the States, and on the distribution of power and
responsibilities among the various levels of government;
(3) The regulatory burden on small businesses, small organizations
and small governmental jurisdictions;
(4) The recordkeeping and reporting requirements and to whom they
would apply; and
(5) Impacts on the quality of the natural and social environments.
(d) The Associate Administrator for Hazardous Materials Safety or
Chief Counsel may return a petition that does not comply with the
requirements of this section, accompanied by a written statement
indicating the deficiencies in the petition.
[Amdt. 106-11, 61 FR 30180, June 14, 1996, as amended by Amdt. 106-13,
61 FR 51336, Oct. 1, 1996]
Sec. 106.33 Processing of petition.
(a) General. Unless the Associate Administrator or the Chief Counsel
otherwise specifies, no public hearing, argument, or other proceeding is
held directly on a petition before its disposition under this section.
(b) Grants. If the Associate Administrator or the Chief Counsel
determines that the petition contains adequate justification, he or she
initiates rulemaking action under this subpart.
(c) Denials. If the Associate Administrator or the Chief Counsel
determines that the petition does not justify rulemaking, the petition
is denied.
(d) Notification. The Associate Administrator or the Chief Counsel
will notify a petitioner, in writing, of the decision to grant or deny a
petition for rulemaking.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-11, 61 FR 30181,
June 14, 1996; Amdt. 106-13, 61 FR 51336, Oct. 1, 1996]
Sec. 106.35 Petitions for reconsideration.
(a) Except as provided in Sec. 106.39(d), any interested person may
petition the Associate Administrator for reconsideration of any
regulation issued under this part, or may petition the Chief Counsel for
reconsideration of any procedural regulation issued under this part and
contained in this part or in part 107 of this chapter. It is requested,
but not required, that three copies be submitted. The petition must be
received not later than 30 days after publication of the rule in the
Federal Register. Petitions filed after that time will be considered as
petitions filed under Sec. 106.31. The petition must contain a brief
statement of the complaint and an explanation as to why compliance with
the rule is not practicable, is unreasonable, or is not in the public
interest.
(b) If the petitioner requests the consideration of additional
facts, the petitioner must state the reason they were not presented to
the Associate Administrator or the Chief Counsel within the prescribed
time.
(c) The Associate Administrator or the Chief Counsel does not
consider repetitious petitions.
(d) Unless the Associate Administrator or the Chief Counsel
otherwise provides, the filing of a petition under this section does not
stay the effectiveness of the rule.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-11, 61 FR 30181,
June 14, 1996; Amdt. 106-13, 61 FR 51337, Oct. 1, 1996]
Sec. 106.37 Proceedings on petitions for reconsideration.
(a) The Associate Administrator or the Chief Counsel may grant or
deny, in whole or in part, any petition for reconsideration without
further proceedings, except where a grant of the petition would result
in issuance of a new final rule. In the event that the
[[Page 11]]
Associate Administrator or the Chief Counsel determines to reconsider
any regulation, a final decision on reconsideration may be issued
without further proceedings, or an opportunity to submit comment or
information and data as deemed appropriate may be provided. Whenever the
Associate Administrator or the Chief Counsel determines that a petition
should be granted or denied, the Office of the Chief Counsel prepares a
notice of the grant or denial of a petition for reconsideration, for
issuance to the petitioner, and the Associate Administrator or the Chief
Counsel issues it to the petitioner. The Associate Administrator or the
Chief Counsel may consolidate petitions relating to the same rules.
(b) It is the policy of the Associate Administrator or the Chief
Counsel to issue notice of the action taken on a petition for
reconsideration within 90 days after the date on which the regulation in
question is published in the Federal Register, unless it is found
impracticable to take action within that time. In cases where it is so
found and the delay beyond that period is expected to be substantial,
notice of that fact and the date by which it is expected that action
will be taken is issued to the petitioner and published in the Federal
Register.
[40 FR 31768, July 29, 1975. Redesignated by Amdt. 102-1, and Amdt. 106-
1, 43 FR 43306, Sept. 25, 1978, as amended by Amdt. 106-11, 61 FR 30181,
June 14, 1996; Amdt. 106-13, 61 FR 51337, Oct. 1, 1996]
Sec. 106.38 Appeals.
(a) Any interested person may appeal a decision of the Associate
Administrator or the Chief Counsel, issued under Sec. 106.33 or
Sec. 106.37, to the Administrator.
(b) An appeal must be received within 20 days of service of written
notice to petitioner of the Associate Administrator's or the Chief
Counsel's decision, or within 20 days from the date of publication of
the decision in the Federal Register, and should set forth the contested
aspects of the decision as well as any new arguments or information.
(c) It is requested, but not required, that three copies of the
appeal be submitted to the Administrator.
(d) Unless the Administrator otherwise provides, the filing of an
appeal under this section does not stay the effectiveness of any rule.
[Amdt. 106-11, 61 FR 30181, June 14, 1996]
Sec. 106.39 Direct final rulemaking.
(a) Where practicable, the Administrator will use direct final
rulemaking to issue the following types of rules:
(1) Minor, substantive changes to regulations;
(2) Incorporation by reference of the latest edition of technical or
industry standards;
(3) Extensions of compliance dates; and
(4) Other noncontroversial rules where the Administrator determines
that use of direct final rulemaking is in the public interest, and that
a regulation is unlikely to result in adverse comment.
(b) The direct final rule will state an effective date. The direct
final rule will also state that unless an adverse comment or notice of
intent to file an adverse comment is received within the specified
comment period, generally 60 days after publication of the direct final
rule in the Federal Register, the Administrator will issue a
confirmation document, generally within 15 days after the close of the
comment period, advising the public that the direct final rule will
either become effective on the date stated in the direct final rule or
at least 30 days after the publication date of the confirmation
document, whichever is later.
(c) For purposes of this section, an adverse comment is one which
explains why the rule would be inappropriate, including a challenge to
the rule's underlying premise or approach, or would be ineffective or
unacceptable without a change. Comments that are frivolous or
insubstantial will not be considered adverse under this procedure. A
comment recommending a rule change in addition to the rule will not be
considered an adverse comment, unless the commenter states why the rule
would be ineffective without the additional change.
(d) Only parties who filed comments to a direct final rule issued
under this section may petition under Sec. 106.35 for
[[Page 12]]
reconsideration of that direct final rule.
(e) If an adverse comment or notice of intent to file an adverse
comment is received, a timely document will be published in the Federal
Register advising the public and withdrawing the direct final rule in
whole or in part. The Administrator may then incorporate the adverse
comment into a subsequent direct final rule or may publish a notice of
proposed rulemaking. A notice of proposed rulemaking will provide an
opportunity for public comment, generally a minimum of 60 days, and will
be processed in accordance with Secs. 106.11-106.29.
[Amdt. 106-11, 61 FR 30181, June 14, 1996]
PART 107--HAZARDOUS MATERIALS PROGRAM PROCEDURES--Table of Contents
Subpart A--General Provisions
Sec.
107.1 Purpose and scope.
107.3 Definitions.
107.5 Request for confidential treatment.
107.7 Service of process on non-residents of the United States.
107.9 Public docket room.
107.11 Service.
107.13 Subpoenas, witness fees.
107.14 Availability of informal guidance and interpretive assistance.
Subpart B--Exemptions
107.101 Purpose and scope.
107.105 Application for exemption.
107.107 Application for party status.
107.109 Application for renewal.
107.111 Withdrawal.
107.113 Application processing and evaluation.
107.117 Emergency processing.
107.121 Modification, suspension or termination of exemption or grant
of party status.
107.123 Reconsideration.
107.125 Appeal.
107.127 Availability of documents for public inspection.
Subpart C--Preemption
107.201 Purpose and scope.
107.202 Standards for determining preemption.
Preemption Determinations
107.203 Application.
107.205 Notice.
107.207 Processing.
107.209 Determination.
107.211 Petition for reconsideration.
107.213 Judicial review.
Waiver of Preemption Determinations
107.215 Application.
107.217 Notice.
107.219 Processing.
107.221 Determination.
107.223 Petition for reconsideration.
107.227 Judicial review.
Subpart D--Enforcement
107.301 Delegated authority for enforcement.
107.303 Purpose and scope.
107.305 Investigations.
Compliance Orders and Civil Penalties
107.307 General.
107.309 Warning letters.
107.310 Ticketing.
107.311 Notice of probable violation.
107.313 Reply.
107.315 Admission of violations.
107.317 Informal response.
107.319 Request for a hearing.
107.321 Hearing.
107.323 ALJ's decision.
107.325 Appeals.
107.327 Compromise and settlement.
107.329 Maximum penalties.
107.331 Assessment considerations.
Criminal Penalties
107.333 Criminal penalties generally.
107.335 Referral for prosecution.
107.336 Limitation on fines and penalties.
Injunctive Action
107.337 Injunctions generally.
107.339 Imminent hazards.
Appendix A to Subpart D of Part 107--Guidelines for Civil Penalties
Subpart E--Designation of Approval and Certification Agencies
107.401 Purpose and scope.
107.402 Application for designation as an approval or certification
agency.
107.403 Designation of approval agencies.
107.404 Conditions of designation.
107.405 Termination of designation.
Subpart F--Registration of Cargo Tank and Cargo Tank Motor Vehicle
Manufacturers and Repairers and Cargo Tank Motor Vehicle Assemblers
107.501 Scope.
107.502 General registration requirements.
107.503 Registration statement.
107.504 Period of registration, updates, and record retention.
[[Page 13]]
Subpart G--Registration of Persons Who Offer or Transport Hazardous
Materials
107.601 Applicability.
107.606 Exceptions.
107.608 General registration requirements.
107.612 Amount of fee.
107.616 Payment procedures.
107.620 Recordkeeping requirements.
Subpart H--Approvals, Registrations and Submissions
107.701 Purpose and scope.
107.705 Registrations, reports, and applications for approval.
107.709 Processing of an application for approval, including an
application for renewal or modification.
107.711 Withdrawal.
107.713 Approval modification, suspension or termination.
107.715 Reconsideration.
107.717 Appeal.
Authority: 49 U.S.C. 5101-5127, 44701; Sec. 212-213, Pub. L. 104-
121, 110 Stat. 857; 49 CFR 1.45, 1.53.
Subpart A--General Provisions
Sec. 107.1 Purpose and scope.
(a) This part prescribes procedures utilized by the Research and
Special Programs Administration, the Associate Administrator and the
Office of Chief Counsel in carrying out their duties under the laws
pertaining to the transportation of hazardous materials.
(b) This subpart defines certain terms and prescribes procedures
that are applicable to each proceeding described in this part.
[40 FR 48470, Oct. 15, 1975, as amended by Amdt. 107-4, 43 FR 43307,
Sept. 25, 1978; Amdt. 107-23, 56 FR 66156, Dec. 20, 1991; 66 FR 45377,
Aug. 28, 2001]
Sec. 107.3 Definitions.
All terms defined in 49 U.S.C. 5102 are used in their statutory
meaning. Other terms used in this part are defined as follows:
Acting knowingly means acting or failing to act while
(1) Having actual knowledge of the facts giving rise to the
violation, or
(2) Having the knowledge that a reasonable person acting in the same
circumstances and exercising due care would have had.
Administrator means the Administrator, Research and Special Programs
Administration.
Applicant means the person in whose name an exemption, approval,
registration, a renewed or modified exemption or approval, or party
status to an exemption is requested to be issued.
Application means a request under subpart B of this part for an
exemption, a renewal or modification of an exemption, party status to an
exemption, or a request under subpart H of this part for an approval, or
renewal or modification of an approval.
Approval means a written authorization, including a competent
authority approval, from the Associate Administrator to perform a
function for which prior authorization by the Associate Administrator is
required under subchapter C of this chapter.
Approval Agency means an organization or a person designated by the
RSPA to certify packagings as having been designed, manufactured,
tested, modified, marked or maintained in compliance with applicable DOT
regulations.
Associate Administrator means the Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration.
Competent Authority means a national agency responsible under its
national law for the control or regulation of a particular aspect of the
transportation of hazardous materials (dangerous goods). The term
Appropriate authority, as used in the ICAO Technical Instructions, has
the same meaning as Competent Authority. The Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration, is the United States Competent Authority for purposes of
this part.
Competent Authority Approval means an approval by the competent
authority which is required under the provisions of an international
standard, such as the International Civil Aviation Organization's
Technical Instructions for the Safe Transport of Dangerous Goods by Air
or the International Maritime Dangerous Goods Code. To the extent that
it satisfies the requirement of the international standard, any of the
following may serve as
[[Page 14]]
a competent authority approval: a specific regulation of this subchapter
or subchapter C of this chapter, an exemption or approval issued under
the provisions of this subchapter or subchapter C of this chapter, or a
separate document issued to one or more persons by the Associate
Administrator.
DOT or Department means U.S. Department of Transportation.
Exemption means a document issued under the authority of 49 U.S.C.
5117 by the Associate Administrator that authorizes a person to perform
a function that is not otherwise authorized under this subchapter,
subchapter C, or other regulations issued under 49 U.S.C. 5101-5127
(e.g., Federal Motor Carrier Safety Administration routing).
Federal hazardous material transportation law means 49 U.S.C. 5101
et seq.
Filed means received at the Research and Special Programs
Administration office designated in the applicable provision or, if no
office is specified, at the Office of Hazardous Materials Exemptions and
Approvals (DHM-30), Research and Special Programs Administration, U.S.
Department of Transportation, 400 7th Street SW., Washington DC, 20590-
0001.
Holder means the person in whose name an exemption or approval has
been issued.
Imminent Hazard means the existence of a condition which presents a
substantial likelihood that death, serious illness, severe personal
injury, or substantial endangerment to health, property, or the
environment may occur before the reasonably foreseeable completion of an
administrative hearing or other formal proceeding initiated to abate the
risks of those effects.
Incident means an event resulting in the unintended and
unanticipated release of a hazardous material or an event meeting
incident reporting requirements in Sec. 171.15 or Sec. 171.16 of this
chapter.
Indian Tribe shall have the meaning given that term under section 4
of the Indian Self-Determination and Education Act (25 U.S.C. 450b).
Investigation includes investigations authorized under 49 U.S.C.
5121 and inspections authorized under 49 U.S.C. 5118 and 5121.
Manufacturing exemption means an exemption from compliance with
specified requirements that otherwise must be met before representing,
marking, certifying (including requalifying, inspecting, and testing),
selling or offering a packaging or container as meeting the requirements
of subchapter C of this chapter governing its use in the transportation
in commerce of a hazardous material. A manufacturing exemption is an
exemption issued to a manufacturer of packagings who does not offer for
transportation or transport hazardous materials in packagings subject to
the exemption.
Party means a person, other than a holder, authorized to act under
the terms of an exemption.
Person means an individual, firm, copartnership, corporation,
company, association, joint-stock association, including any trustee,
receiver, assignee, or similar representative thereof, or government,
Indian tribe, or agency or instrumentality of any government or Indian
tribe when it offers hazardous materials for transportation in commerce
or transports hazardous materials in furtherance of a commercial
enterprise, but such term does not include:
(1) The United States Postal Service, or
(2) For the purposes of 49 U.S.C. 5123 and 5124, any agency or
instrumentality of the Federal Government.
Registration means a written acknowledgment from the Associate
Administrator that a registrant is authorized to perform a function for
which registration is required under subchapter C of this chapter (e.g.,
registration with RSPA as a cylinder retester pursuant to 49 CFR
173.34(e)(1), or registration in accordance with 49 CFR 178.503
regarding marking of packagings). For purposes of subparts A through E,
``registration'' does not include registration under subpart F or G of
this part.
Report means information, other than an application, registration or
part thereof, required to be submitted to the Associate Administrator
pursuant to this subchapter, subchapter B or subchapter C of this
chapter.
[[Page 15]]
Respondent means a person upon whom the RSPA has served a notice of
probable violation.
State means a State of the United States, the District of Columbia,
the Commonwealth of Puerto Rico, the Commonwealth of the Northern
Mariana Islands, the Virgin Islands, American Samoa, Guam, or any other
territory or possession of the United States designated by the
Secretary; except that as used in 49 U.S.C. 5119, relating to uniformity
of State registration and permitting forms and procedures, such term
means a State of the United States and the District of Columbia.
Transports or transportation means any movement of property by any
mode, and any loading, unloading, or storage incidental thereto.
[Amdt. 107-3, 41 FR 38170, Sept. 9, 1976, as amended by Amdt. 107-4, 43
FR 43307, Sept. 25, 1978; Amdt. 107-5, 43 FR 48642, Oct. 19, 1978; Amdt.
107-8, 46 FR 9888, Jan. 29, 1981; Amdt. 107-12, 48 FR 53711, Nov. 29,
1983; 50 FR 45730, Nov. 1, 1985; Amdt. 107-24, 56 FR 8621, Feb. 28,
1991; Amdt. 107-23, 56 FR 66157, Dec. 20, 1991; Amdt. 107-32, 59 FR
49130, Sept. 26, 1994; Amdt. 107-38, 61 FR 21094, May 9, 1996; 65 FR
58618, Sept. 29, 2000; 66 FR 45377, Aug. 28, 2001]
Sec. 107.5 Request for confidential treatment.
(a) If any person filing a document with the Associate Administrator
claims that some or all the information contained in the document is
exempt from the mandatory public disclosure requirements of the Freedom
of Information Act (5 U.S.C. 552), is information referred to in 18
U.S.C. 1905, or is otherwise exempt by law from public disclosure, and
if that person requests the Associate Administrator not to disclose the
information, that person shall file, together with the document, a
second copy of the document with the confidential information deleted.
The person shall indicate each page of the original document that is
confidential or contains confidential information by marking or stamping
``confidential'' on each page for which a claim of confidentiality is
made, and may file a statement specifying the justification for the
claim of confidentiality. If the person states that the information
comes within the exception in 5 U.S.C. 552(b)(4) for trade secrets and
commercial or financial information, that person shall include a
statement as to why the information is privileged or confidential. If
the person filing a document does not mark or stamp a document as
confidential or submit a second copy of the document with the
confidential information deleted, the Associate Administrator may assume
that there is no objection to public disclosure of the document in its
entirety.
(b) The Associate Administrator retains the right to make its own
determination with regard to any claim of confidentiality. Notice of a
decision by the Associate Administrator to deny the claim, in whole or
in part, and an opportunity to respond shall be given to a person
claiming confidentiality of information no less than five days prior to
its public disclosure.
[40 FR 48470, Oct. 15, 1975, as amended by Amdt. 107-24, 56 FR 8621,
Feb. 28, 1991; Amdt. 107-38, 61 FR 21095, May 9, 1996]
Sec. 107.7 Service of process on non-residents of the United States.
(a) Designation of agent for service. When a person who is not a
resident of the United States is required by this subchapter or
subchapter C of this chapter to designate a permanent resident of the
United States as his agent upon whom service of process may be made for
him and on his behalf, the agent may be an individual, a firm, or a
domestic corporation. Any number of principals may designate the same
person as agent. A designation is binding on a principal even if the
designation is not in compliance with all the requirements of this
section, until rejected by the Associate Administrator. A designated
agent may not assign performance of his functions under the designation
to another person.
(b) Form and contents of designation. The designation shall:
(1) Be in writing and dated;
(2) Be made in the legal form required to make it valid and binding
on the principal under the laws, corporate bylaws, or other requirements
governing the making of the designation by the principal at the place
and time where it is made and the person or persons signing the
designation shall certify that it is so made;
[[Page 16]]
(3) State the full legal name, principal name of business and
mailing address of the principal;
(4) Provide that it remains in effect until withdrawn or replaced by
the principal;
(5) State the legal name and mailing address of the agent; and
(6) Bear a declaration of acceptance duly signed by the designated
agent.
(c) Method of service. Service of any process, notice, order,
decision, or requirement of the Associate Administrator may be made by
registered or certified mail addressed to the agent with return receipt
requested or in any other manner authorized by law. If service cannot be
effected because the agent has died (or, if a firm or a corporation
ceases to exist) or moved, or otherwise does not receive correctly
addressed mail, service may be made by publication in the Federal
Register.
[Amdt. 107-2, 41 FR 7509, Feb. 19, 1976, as amended by Amdt. 107-24, 56
FR 8621, Feb. 28, 1991; 66 FR 45377, Aug. 28, 2001]
Sec. 107.9 Public docket room.
There is established in the RSPA offices at 400 7th Street, SW.,
Washington, DC, a public docket room in which there is available for
public inspection and copying:
(a) Copies of notices of proposed rulemaking issued by the RSPA or
its predecessor agency, including advance notices, together with the
comments received thereon during rulemaking proceedings, copies of any
related Federal Register notices, final rules, petitions for
reconsideration, and decisions issued in response to petitions for
reconsideration;
(b) Applications for exemptions from the Department of
Transportation's regulations governing the transportation of hazardous
materials, including supporting data, memoranda of any informal meetings
with applicants, related Federal Register notices, comments received
thereon during the public comment period and copies of decisions issued
granting or denying applications for exemptions;
(c) Applications for preemption and waiver of preemption
determinations under subpart C of this part, together with the comments
received thereon, related documents filed with the RSPA, copies of
related Federal Register notices, and rulings, determinations and orders
issued in response to those applications;
(d) Records of compliance order proceedings and copies of RSPA
compliance orders;
(e) Appeals filed under this part and RSPA decisions issued in
response to those appeals; and
(f) Such other information pertaining to the RSPA's hazardous
materials program required by statute to be made available for public
inspection and copying and any information which the RSPA determines
should be made available to the public.
[Amdt. 107-3, 41 FR 38170, Sept. 9, 1976, as amended by Amdt. 107-8, 45
FR 81571, Dec. 11, 1980; Amdt. 107-24, 56 FR 8622, Feb. 28, 1991]
Sec. 107.11 Service.
(a) Each order, notice, or other document required to be served
under this part shall be served personally or by registered or certified
mail, except as otherwise provided.
(b) Service upon a person's duly authorized representative
constitutes service upon that person.
(c) Service by registered or certified mail is complete upon
mailing. An official United States Postal Service receipt from the
registered or certified mailing constitutes prima facie evidence of
service.
[Amdt. 107-3, 41 FR 38170, Sept. 9, 1976]
Sec. 107.13 Subpoenas, witness fees.
(a) The Administrator, RSPA, the Chief Counsel, Research and Special
Programs Administration, or the Official designated to preside over a
hearing convened in accordance with this part, may sign and issue
subpoenas either on his own initiative or, upon an adequate showing that
the information sought will materially advance the proceeding, upon the
request of any person participating in that proceeding.
(b) A subpoena may require the attendance of a witness, or the
production of documentary or other tangible evidence in the possession
or under the control of the person served, or both.
[[Page 17]]
(c) A subpoena may be served personally by any person who is not an
interested person and is not less than 18 years of age, or by certified
or registered mail.
(d) Service of a subpoena upon the person named therein shall be
made by delivering a copy of the subpoena to such person and by
tendering the fees for one day's attendance and mileage as specified by
paragraph (f) of this section. When a subpoena is issued at the instance
of any officer or agency of the United States, fees and mileage need not
be tendered at the time of service. Delivery of a copy of a subpoena and
tender of the fees to a natural person may be made by handing them to
the person, leaving them at his office with the person in charge
thereof, leaving them at his dwelling place or usual place of abode with
some person of suitable age and discretion then residing therein, by
mailing them by registered or certified mail to him at his last known
address, or by any method whereby actual notice is given to him and the
fees are made available prior to the return date. When the person to be
served is not a natural person, delivery of a copy of the subpoena and
tender of the fees may be effected by handing them to a registered agent
for service, or to any officer, director, or agent in charge of any
office of the person, or by mailing them by registered or certified mail
to that representative at his last known address or by any method
whereby actual notice is given to the representative and the fees are
made available prior to the return date.
(e) The original subpoena bearing a certificate of service shall be
filed with the RSPA official having responsibility for the proceeding in
connection with which the subpoena was issued.
(f) A witness subpoenaed by the RSPA shall be paid the same fees and
mileage as would be paid to a witness in a proceeding in the district
courts of the United States. The witness fees and mileage shall be paid
by the person at whose instance the subpoena was issued.
(g) Notwithstanding the provisions of paragraph (f) of this section,
and upon request, the witness fees and mileage may be paid by the RSPA
if the RSPA official who issued the subpoena determines on the basis of
good cause shown, that:
(1) The presence of the subpoenaed witness will materially advance
the proceeding; and
(2) The person at whose instance the subpoena was issued would
suffer a serious hardship if required to pay the witness fees and
mileage.
(h) Any person to whom a subpoena is directed may apply no later
than 10 days after service thereof, to the person who issued the
subpoena to quash or modify it. The application shall contain a brief
statement of the reasons relied upon in support of the action sought
therein. The person who issued the subpoena may:
(1) Deny the application;
(2) Quash or modify the subpoena; or
(3) Condition denial of the application to quash or modify the
subpoena upon the satisfaction of certain just and reasonable
requirements. The denial may be summary.
(i) If there is a refusal to obey a subpoena served upon any person
under the provisions of this section, the RSPA may request the Attorney
General to seek the aid of the United States District Court for any
District in which the person is found to compel that person, after
notice, to appear and give testimony, or to appear and produce the
subpoenaed documents before the RSPA, or both.
[Amdt. 107-3, 41 FR 38170, Sept. 9, 1976, as amended by Amdt. 107-11, 48
FR 2651, Jan. 20, 1983]
Sec. 107.14 Availability of informal guidance and interpretive assistance.
(a) Availability of telephonic and Internet assistance. (1) RSPA has
a toll-free, telephonic information line which provides answers to
inquiries by small entities and other parties concerning information on
and advice about compliance with the hazardous materials regulations, 49
CFR parts 171-180. The information line is staffed from 9:00 a.m.
through 5:00 p.m., Eastern time, Monday through Friday, except Federal
holidays. When the information line is not staffed, callers may leave a
recorded message, which will be answered by the end of the next business
day. The telephone numbers for the information line are: 1-800-HMR-4922
(that
[[Page 18]]
is; 1-800-467-4922 toll free), or 202-366-4488 (in the Washington, D.C.
area). Additionally, information may be obtained from the Office of
Hazardous Materials Safety via the Internet at http://hazmat.dot.gov.
(2) RSPA's Office of the Chief Counsel (OCC) is available to answer
questions concerning Federal hazardous material transportation law, 49
USC 5101 et seq. and Federal preemption of state, local and Indian tribe
hazardous material transportation requirements. OCC may be contacted by
telephone (202-366-4400) from 9:00 a.m. to 4:00 p.m. Eastern time,
Monday through Friday, except Federal holidays. Information and guidance
concerning Federal hazardous material transportation law and preemption
may also be obtained by contacting OCC via the Internet at http://rspa-
atty.dot.gov.
(b) Availability of Written Interpretations. (1) A written
regulatory clarification, response to a question, or an opinion
concerning hazardous materials offering, transporting, or packaging
requirements may be obtained by submitting a written request to the RSPA
Office of Hazardous Materials Standards (DHM-10), U.S. Department of
Transportation, 400 Seventh Street, SW., Washington, DC 20590-0001. The
requestor must include his or her return address and should also include
a daytime telephone number.
(2) A written interpretation regarding Federal hazardous material
transportation law, 49 USC 5101 et seq., may be obtained from the Office
of the Chief Counsel (DCC-1) RSPA, U.S. Department of Transportation,
400 Seventh Street, SW., Washington, DC 20590-0001. The requestor must
include his or her return address and should also include a daytime
telephone number.
[62 FR 24057, May 2, 1997 as amended at 62 FR 34415, June 26, 1997; 64
FR 51914, Sept. 27, 1999; 65 FR 58618, Sept. 29, 2000]
Subpart B--Exemptions
Source: Amdt. 107-38, 61 FR 21095, May 9, 1996, unless otherwise
noted.
Sec. 107.101 Purpose and scope.
This subpart prescribes procedures for the issuance, modification
and termination of exemptions from requirements of this subchapter,
subchapter C of this chapter, or regulations issued under chapter 51 of
49 U.S.C.
Sec. 107.105 Application for exemption.
(a) General. Each application for an exemption or modification of an
exemption must be written in English and must--
(1) Be submitted in duplicate and, for timely consideration, at
least 120 days before the requested effective date to: Associate
Administrator for Hazardous Materials Safety, Research and Special
Programs Administration, U.S. Department of Transportation, 400 7th
Street, SW, Washington, DC 20590-0001. Attention: Exemptions, DHM-31;
(2) State the name, street and mailing addresses, e-mail address
optional, and telephone number of the applicant; if the applicant is not
an individual, state the name, street and mailing addresses, e-mail
address optional, and telephone number of an individual designated as an
agent of the applicant for all purposes related to the application;
(3) If the applicant is not a resident of the United States, a
designation of agent for service in accordance with Sec. 107.7 of this
part; and
(4) For a manufacturing exemption, a statement of the name and
street address of each facility where manufacturing under the exemption
will occur.
(b) Confidential treatment. To request confidential treatment for
information contained in the application, the applicant shall comply
with Sec. 107.5(a).
(c) Description of exemption proposal. The application must include
the following information that is relevant to the exemption proposal:
(1) A citation of the specific regulation from which the applicant
seeks relief;
(2) Specification of the proposed mode or modes of transportation;
(3) A detailed description of the proposed exemption (e.g.,
alternative packaging, test, procedure or activity) including, as
appropriate, written descriptions, drawings, flow charts, plans and
other supporting documents;
(4) A specification of the proposed duration or schedule of events
for which the exemption is sought;
(5) A statement outlining the applicant's basis for seeking relief
from
[[Page 19]]
compliance with the specified regulations and, if the exemption is
requested for a fixed period, a description of how compliance will be
achieved at the end of that period;
(6) If the applicant seeks emergency processing specified in
Sec. 107.117, a statement of supporting facts and reasons;
(7) Identification and description of the hazardous materials
planned for transportation under the exemption;
(8) Description of each packaging, including specification or
exemption number, as applicable, to be used in conjunction with the
requested exemption;
(9) For alternative packagings, documentation of quality assurance
controls, package design, manufacture, performance test criteria, in-
service performance and service-life limitations.
(d) Justification of exemption proposal. The application must
demonstrate that an exemption achieves a level of safety at least equal
to that required by regulation, or if a required safety level does not
exist, is consistent with the public interest. At a minimum, the
application must provide the following:
(1) Information describing all relevant shipping and incident
experience of which the applicant is aware that relates to the
application;
(2) A statement identifying any increased risk to safety or property
that may result if the exemption is granted, and a description of the
measures to be taken to address that risk; and
(3) Either--
(i) Substantiation, with applicable analyses, data or test results,
that the proposed alternative will achieve a level of safety that is at
least equal to that required by the regulation from which the exemption
is sought; or
(ii) If the regulations do not establish a level of safety, an
analysis that identifies each hazard, potential failure mode and the
probability of its occurrence, and how the risks associated with each
hazard and failure mode are controlled for the duration of an activity
or life-cycle of a packaging.
[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 62 FR 51556, Oct.
1, 1997; 65 FR 50457, Aug. 18, 2000; 65 FR 58618, Sept. 29, 2000]
Sec. 107.107 Application for party status.
(a) Any person eligible to apply for an exemption may apply to be
made party to an application or an existing exemption, other than a
manufacturing exemption.
(b) Each application filed under this section must--
(1) Be submitted in duplicate to: Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration, U.S. Department of Transportation, 400 7th Street, SW,
Washington, DC 20590-0001. Attention: Exemptions, DHM-31;
(2) Identify by number the exemption application or exemption to
which the applicant seeks to become a party;
(3) State the name, street and mailing addresses, e-mail address
optional, and telephone number of the applicant; if the applicant is not
an individual, state the name, street and mailing addresses, e-mail
address optional, and telephone number of an individual designated as
the applicant's agent for all purposes related to the application; and
(4) If the applicant is not a resident of the United States, provide
a designation of agent for service in accordance with Sec. 107.7.
(c) The Associate Administrator grants or denies an application for
party status in the manner specified in Sec. 107.113(e) and (f) of this
subpart.
(d) A party to an exemption is subject to all terms of that
exemption, including the expiration date. If a party to an exemption
wishes to renew party status, the exemption renewal procedures set forth
in Sec. 107.109 apply.
[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 65 FR 50457, Aug.
18, 2000]
Sec. 107.109 Application for renewal.
(a) Each application for renewal of an exemption or party status to
an exemption must--
(1) Be submitted in duplicate to: Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration, U.S. Department of Transportation, 400 7th Street, SW,
Washington, DC 20590-0001. Attention: Exemptions, DHM-31;
(2) Identify by number the exemption for which renewal is requested;
[[Page 20]]
(3) State the name, street and mailing addresses, e-mail address
optional, and telephone number of the applicant; if the applicant is not
an individual, state the name, street and mailing addresses, e-mail
address optional, and telephone number of an individual designated as an
agent of the applicant for all purposes related to the application;
(4) Include either a certification by the applicant that the
original application, as it may have been updated by any application for
renewal, remains accurate and complete; or include an amendment to the
previously submitted application as is necessary to update and assure
the accuracy and completeness of the application, with certification by
the applicant that the application as amended is accurate and complete;
and
(5) Include a statement describing all relevant shipping and
incident experience of which the applicant is aware in connection with
the exemption since its issuance or most recent renewal. If the
applicant is aware of no incidents, the applicant shall so certify. When
known to the applicant, the statement should indicate the approximate
number of shipments made or packages shipped, as the case may be, and
number of shipments or packages involved in any loss of contents,
including loss by venting other than as authorized in subchapter C.
(b) If at least 60 days before an existing exemption expires the
holder files an application for renewal that is complete and conforms to
the requirements of this section, the exemption will not expire until
final administrative action on the application for renewal has been
taken.
[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 65 FR 50457, Aug.
18, 2000]
Sec. 107.111 Withdrawal.
An application may be withdrawn at any time before a decision to
grant or deny it is made. Withdrawal of an application does not
authorize the removal of any related records from the RSPA dockets or
files. Applications that are eligible for confidential treatment under
Sec. 107.5 will remain confidential after the application is withdrawn.
The duration of this confidential treatment for trade secrets and
commercial or financial information is indefinite, unless the party
requesting the confidential treatment of the materials notifies the
Associate Administrator that the confidential treatment is no longer
required.
Sec. 107.113 Application processing and evaluation.
(a) The Associate Administrator reviews an application for
exemption, modification of exemption, party to exemption, or renewal of
an exemption to determine if it is complete and conforms with the
requirements of this subpart. This determination will be made within 30
days of receipt of the application for exemption, modification of
exemption, or party to exemption, and within 15 days of receipt of an
application for renewal of an exemption. If an application is determined
to be incomplete, the applicant is informed of the reasons.
(b) An application, other than a renewal, party to, or emergency
exemption application, that is determined to be complete is docketed.
Notice of the application is published in the Federal Register, and an
opportunity for public comment is provided. All comments received during
the comment period are considered before final action is taken on the
application.
(c) No public hearing or other formal proceeding is required under
this subpart before the disposition of an application. Unless emergency
processing under Sec. 107.117 is requested and granted, applications are
usually processed in the order in which they are filed.
(d) During the processing and evaluation of an application, the
Associate Administrator may request additional information from the
applicant. If the applicant does not respond to a written request for
additional information within 30 days of the date the request was
received, the application may be deemed incomplete and denied. However,
if the applicant responds in writing within the 30-day period requesting
an additional 30 days within which it will gather the requested
information, the Associate Administrator may grant the 30-day extension.
(e) The Associate Administrator may grant or deny an application, in
whole
[[Page 21]]
or in part. In the Associate Administrator's discretion, an application
may be granted subject to provisions that are appropriate to protect
health, safety or property. The Associate Administrator may impose
additional provisions not specified in the application or remove
conditions in the application that are unnecessary.
(f) The Associate Administrator may grant an application on finding
that--
(1) The application complies with this subpart;
(2) The application demonstrates that the proposed alternative will
achieve a level of safety that:
(i) Is at least equal to that required by the regulation from which
the exemption is sought, or
(ii) If the regulations do not establish a level of safety, is
consistent with the public interest and adequately will protect against
the risks to life and property inherent in the transportation of
hazardous materials in commerce;
(3) The application states all material facts, and contains no
materially false or materially misleading statement;
(4) The applicant meets the qualifications required by applicable
regulations; and
(5) The applicant is fit to conduct the activity authorized by the
exemption. This assessment may be based on information in the
application, prior compliance history of the applicant, and other
information available to the Associate Administrator.
(g) An applicant is notified in writing whether the application is
granted or denied. A denial contains a brief statement of reasons.
(h) An exemption and any renewal thereof terminates according to its
terms or, if not otherwise specified, two years after the date of
issuance. A grant of party status to an exemption, unless otherwise
stated, terminates on the date that the exemption expires.
(i) The Associate Administrator, on determining that an application
concerns a matter of general applicability and future effect and should
be the subject of rulemaking, may initiate rulemaking under part 106 of
this chapter in addition to or instead of acting on the application.
(j) The Associate Administrator publishes in the Federal Register a
list of all exemption grants, denials, and modifications and all
exemption applications withdrawn under this section.
Sec. 107.117 Emergency processing.
(a) An application is granted emergency processing if the Associate
Administrator, on the basis of the application and any inquiry
undertaken, finds that--
(1) Emergency processing is necessary to prevent significant injury
to persons or property (other than the hazardous material to be
transported) that could not be prevented if the application were
processed on a routine basis; or
(2) Emergency processing is necessary for immediate national
security purposes or to prevent significant economic loss that could not
be prevented if the application were processed on a routine basis.
(b) Where the significant economic loss is to the applicant, or to a
party in a contractual relationship to the applicant with respect to the
activity to be undertaken, the Associate Administrator may deny
emergency processing if timely application could have been made.
(c) A request for emergency processing on the basis of potential
economic loss must reasonably describe and estimate the potential loss.
(d) An application submitted under this section must conform to
Sec. 107.105 to the extent that the receiving Department official deems
necessary to process the application. An application on an emergency
basis must be submitted to the Department modal contact official for the
initial mode of transportation to be utilized, as follows:
(1) Certificate-Holding Aircraft: The Federal Aviation
Administration Civil Aviation Security Office that serves the place
where the flight will originate or that is responsible for the aircraft
operator's overall aviation security program. The nearest Civil Aviation
Security Office may be located by calling the FAA Duty Officer, 202-267-
3333 (any hour).
(2) Noncertificate-Holding Aircraft (Those Which Operate Under 14
CFR Part
[[Page 22]]
91): The Federal Aviation Administration Civil Aviation Security Office
that serves the place where the flight will originate. The nearest Civil
Aviation Security Office may be located by calling the FAA Duty Officer,
202-267-3333 (any hour).
(3) Motor Vehicle Transportation: Director, Office of Motor Carrier
Research and Standards, Federal Motor Carrier Safety Administration,
U.S. Department of Transportation, Washington, DC 20590-0001, 202-366-
4001 (day); 202-267-2100 (night).
(4) Rail Transportation: Staff Director, Hazardous Materials
Division, Office of Safety Assurance and Compliance, Federal Railroad
Administration, U.S. Department of Transportation, Washington, DC 20590-
0001, 202-493-6247 or 202-493-6244 (day); 202-267-2100 (night).
(5) Water Transportation: Chief, Hazardous Materials Standards
Division, Office of Operating and Environmental Standards, United States
Coast Guard, U.S. Department of Transportation, Washington, DC 20593-
0001, 202-267-1577 (day); 202-267-2100 (night).
(e) On receipt of all information necessary to process the
application, the receiving Department official transmits to the
Associate Administrator, by the most rapid available means of
communication, an evaluation as to whether an emergency exists under
Sec. 107.117(a) and, if appropriate, recommendations as to the
conditions to be included in the exemption. If the Associate
Administrator determines that an emergency exists under Sec. 107.117(a)
and that, with reference to the criteria of Sec. 107.113(f), granting of
the application is in the public interest, the Associate Administrator
grants the application subject to such terms as necessary and
immediately notifies the applicant. If the Associate Administrator
determines that an emergency does not exist or that granting of the
application is not in the public interest, the applicant immediately is
so notified.
(f) A determination that an emergency does not exist is not subject
to reconsideration under Sec. 107.123 of this part.
(g) Within 90 days following issuance of an emergency exemption, the
Associate Administrator will publish, in the Federal Register, a notice
of issuance with a statement of the basis for the finding of emergency
and the scope and duration of the exemption.
[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 62 FR 51556, Oct.
1, 1997; 64 FR 51914, Sept. 27, 1999; 65 FR 58618, Sept. 29, 2000; 66 FR
45377, Aug. 28, 2001]
Sec. 107.121 Modification, suspension or termination of exemption or grant of party status.
(a) The Associate Administrator may modify an exemption or grant of
party status on finding that--
(1) Modification is necessary so that an exemption reflects current
statutes and regulations; or
(2) Modification is required by changed circumstances to meet the
standards of Sec. 107.113(f).
(b) The Associate Administrator may modify, suspend or terminate an
exemption or grant of party status, as appropriate, on finding that--
(1) Because of a change in circumstances, the exemption or party
status no longer is needed or no longer would be granted if applied for;
(2) The application contained inaccurate or incomplete information,
and the exemption or party status would not have been granted had the
application been accurate and complete;
(3) The application contained deliberately inaccurate or incomplete
information; or
(4) The holder or party knowingly has violated the terms of the
exemption or an applicable requirement of this chapter, in a manner
demonstrating the holder or party is not fit to conduct the activity
authorized by the exemption.
(c) Except as provided in paragraph (d) of this section, before an
exemption or grant of party status is modified, suspended or terminated,
the Associate Administrator notifies the holder or party in writing of
the proposed action and the reasons for it, and provides an opportunity
to show cause why the proposed action should not be taken.
(1) The holder or party may file a written response that shows cause
why the proposed action should not be taken within 30 days of receipt of
notice of the proposed action.
(2) After considering the holder's or party's written response, or
after 30
[[Page 23]]
days have passed without response since receipt of the notice, the
Associate Administrator notifies the holder or party in writing of the
final decision with a brief statement of reasons.
(d) The Associate Administrator, if necessary to avoid a risk of
significant harm to persons or property, may in the notification declare
the proposed action immediately effective.
Sec. 107.123 Reconsideration.
(a) An applicant for exemption, an exemption holder, or an applicant
for party status to an exemption may request that the Associate
Administrator reconsider a decision under Sec. 107.113(g),
Sec. 107.117(e) or Sec. 107.121(c) of this part. The request must--
(1) Be in writing and filed within 20 days of receipt of the
decision;
(2) State in detail any alleged errors of fact and law;
(3) Enclose any additional information needed to support the request
to reconsider; and
(4) State in detail the modification of the final decision sought.
(b) The Associate Administrator grants or denies, in whole or in
part, the relief requested and informs the requesting person in writing
of the decision. If necessary to avoid a risk of significant harm to
persons or property, the Associate Administrator may, in the
notification, declare the action immediately effective.
Sec. 107.125 Appeal.
(a) A person who requested reconsideration under Sec. 107.123 and is
denied the relief requested may appeal to the Administrator. The appeal
must--
(1) Be in writing and filed within 30 days of receipt of the
Associate Administrator's decision on reconsideration;
(2) State in detail any alleged errors of fact and law;
(3) Enclose any additional information needed to support the appeal;
and
(4) State in detail the modification of the final decision sought.
(b) The Administrator, if necessary to avoid a risk of significant
harm to persons or property, may declare the Associate Administrator's
action effective pending a decision on appeal.
(c) The Administrator grants or denies, in whole or in part, the
relief requested and informs the appellant in writing of the decision.
The Administrator's decision is the final administrative action.
Sec. 107.127 Availability of documents for public inspection.
(a) Documents related to an application under this subpart,
including the application itself, are available for public inspection,
except as specified in paragraph (b) of this section, at the Office of
the Associate Administrator for Hazardous Materials Safety, Research and
Special Programs Administration, RSPA Records Center, U.S. Department of
Transportation, 400 7th Street, SW, Washington, DC 20590-0001, Room
8421. Office hours are 8:30 a.m. to 5:00 p.m., Monday through Friday,
except holidays when the office is closed. Copies of available documents
may be obtained as provided in part 7 of this title. Documents numbered
11832 and above may also be viewed at the internet website address
http://dms.dot.gov.
(b) Documents available for inspection do not include materials
determined to be withheld from public disclosure under Sec. 107.5 and in
accordance with the applicable provisions of section 552(b) of title 5,
United States Code, and part 7 of this title.
[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 65 FR 58618,
Sept. 29, 2000; 66 FR 45377, Aug. 28, 2001]
Subpart C--Preemption
Sec. 107.201 Purpose and scope.
(a) This subpart prescribes procedures by which:
(1) Any person, including a State, political subdivision, or Indian
tribe, directly affected by any requirement of a State, political
subdivision, or Indian tribe, may apply for a determination as to
whether that requirement is preempted under 49 U.S.C. 5125, or
regulations issued thereunder; and
(2) A State, political subdivision, or Indian tribe may apply for a
waiver of preemption with respect to any requirement that the State,
political subdivision, or Indian tribe acknowledges to be preempted by
49 U.S.C. 5125, or regulations issued thereunder, or that has been
determined by a court of
[[Page 24]]
competent jurisdiction to be so preempted.
(b) For purposes of this subpart ``political subdivision'' includes
a municipality; a public agency or other instrumentality of one or more
States, municipalities, or other political subdivisions of a State; or a
public corporation, board, or commission established under the laws of
one or more States.
(c) For purposes of this subpart, ``regulations issued under the
Federal hazardous material transportation law'' means the regulations
contained in this subchapter and subchapter C of this chapter.
(d) Unless otherwise ordered by the Associate Administrator, an
application for a preemption determination which includes an application
for a waiver of preemption will be treated and processed solely as an
application for a preemption determination.
[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56
FR 8622, Feb. 28, 1991; Amdt. 107-25, 57 FR 20428, May 13, 1992; Amdt.
107-32, 59 FR 49130, Sept. 26, 1994; Amdt. 107-35, 60 FR 49108, Sept.
21, 1995; Amdt. 107-38, 61 FR 21098, May 9, 1996]
Sec. 107.202 Standards for determining preemption.
(a) Except as provided in Sec. 107.221 and unless otherwise
authorized by Federal law, any requirement of a State or political
subdivision thereof or an Indian tribe, that concerns one of the
following subjects and that is not substantively the same as any
provision of the Federal hazardous material transportation law, this
subchapter or subchapter C that concerns that subject, is preempted:
(1) The designation, description, and classification of hazardous
material.
(2) The packing, repacking, handling, labeling, marking, and
placarding of hazardous material.
(3) The preparation, execution, and use of shipping documents
pertaining to hazardous material and requirements related to the number,
content, and placement of those documents.
(4) The written notification, recording, and reporting of the
unintentional release in transportation of hazardous material.
(5) The design, manufacturing, fabrication, marking, maintenance,
reconditioning, repairing, or testing of a packaging or a container
which is represented, marked, certified, or sold as qualified for use in
the transportation of hazardous material.
(b) Except as provided in Sec. 107.221 and unless otherwise
authorized by Federal law, any requirement of a State or political
subdivision or Indian tribe is preempted if--
(1) Complying with a requirement of the State, political
subdivision, or Indian tribe and a requirement under the Federal
hazardous material transportation law or regulations issued thereunder
is not possible;
(2) The requirement of the State, political subdivision, or Indian
tribe, as applied or enforced, is an obstacle to accomplishing and
carrying out the Federal hazardous material transportation law or
regulations issued thereunder; or
(3) It is preempted under 49 U.S.C. 5125 (c).
(c) A State, political subdivision, or Indian tribe may impose a fee
related to transporting hazardous material only if the fee is fair and
used for a purpose related to transporting hazardous material, including
enforcement and planning, developing and maintaining a capability for
emergency response.
(d) For purposes of this section, ``substantively the same'' means
that the non-Federal requirement conforms in every significant respect
to the Federal requirement. Editorial and other similar de minimis
changes are permitted.
[Amdt. 107-24, 56 FR 8622, Feb. 28, 1991, as amended by Amdt. 107-25, 57
FR 20428, May 13, 1992; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; Amdt.
107-32, 59 FR 49130, Sept. 26, 1994; Amdt. 107-38, 61 FR 21098, May 9,
1996; Amdt. 107-39, 61 FR 51337, Oct. 1, 1996]
Preemption Determinations
Sec. 107.203 Application.
(a) With the exception of highway routing matters covered under 49
U.S.C. 5125(c), any person, including a State or political subdivision
thereof or an Indian tribe, directly affected by any requirement of a
State or political subdivision thereof or an Indian tribe, may apply to
the Associate Administrator for a determination of whether
[[Page 25]]
that requirement is preempted by Sec. 107.202 (a) or (b).
(b) Each application filed under this section for a determination
must:
(1) Be submitted to Associate Administrator for Hazardous Materials
Safety, Research and Special Programs Administration, U.S. Department of
Transportation, Washington, DC 20590-0001. Attention: Hazardous
Materials Preemption Docket;
(2) Set forth the text of the State or political subdivision or
Indian tribe requirement for which the determination is sought;
(3) Specify each requirement of the Federal hazardous material
transportation law or the regulations issued thereunder with which the
applicant seeks the State or political subdivision or Indian tribe
requirement to be compared;
(4) Explain why the applicant believes the State or political
subdivision or Indian tribe requirement should or should not be
preempted under the standards of Sec. 107.202; and
(5) State how the applicant is affected by the State or political
subdivision or Indian tribe requirement.
(c) The filing of an application for a determination under this
section does not constitute grounds for noncompliance with any
requirement of the Federal hazardous material transportation law or the
regulations issued thereunder.
(d) Once the Associate Administrator has published notice in the
Federal Register of an application received under paragraph (a) of this
section, no applicant for such determination may seek relief with
respect to the same or substantially the same issue in any court until
final action has been taken on the application or until 180 days after
filing of the application, whichever occurs first. Nothing in
Sec. 107.203(a) prohibits a State or political subdivision or Indian
tribe, or any other person directly affected by any requirement of a
State or political subdivision thereof or Indian tribe, from seeking a
determination of preemption in any court of competent jurisdiction in
lieu of applying to the Associate Administrator under paragraph (a) of
this section.
[Amdt. 107-24, 56 FR 8622, Feb. 28, 1991, as amended by Amdt. 107-25, 57
FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt.
107-38, 61 FR 21098, May 9, 1996]
Sec. 107.205 Notice.
(a) If the applicant is other than a State, political subdivision,
or Indian tribe, the applicant shall mail a copy of the application to
the State, political subdivision, or Indian tribe concerned accompanied
by a statement that the State, political subdivision, or Indian tribe
may submit comments regarding the application to the Associate
Administrator. The application filed with the Associate Administrator
must include a certification that the applicant has complied with this
paragraph and must include the names and addresses of each State,
political subdivision, or Indian tribe official to whom a copy of the
application was sent.
(b) The Associate Administrator will publish notice of, including an
opportunity to comment on, an application in the Federal Register and
may notify in writing any person readily identifiable as affected by the
outcome of the determination.
(c) Each person submitting written comments to the Associate
Administrator with respect to an application filed under this section
shall send a copy of the comments to the applicant and certify to the
Associate Administrator that he or she has complied with this
requirement. The Associate Administrator may notify other persons
participating in the proceeding of the comments and provide an
opportunity for those other persons to respond. Late-filed comments are
considered so far as practicable.
[Amdt. 107-38, 61 FR 21098, May 9, 1996]
Sec. 107.207 Processing.
(a) The Associate Administrator may initiate an investigation of any
statement in an application and utilize in his or her evaluation any
relevant facts obtained by that investigation. The Associate
Administrator may solicit and accept submissions from third persons
relevant to an application and will provide the applicant an opportunity
to
[[Page 26]]
respond to all third person submissions. In evaluating an application,
the Associate Administrator may consider any other source of
information. The Associate Administrator on his or her own initiative
may convene a hearing or conference, if he or she considers that a
hearing or conference will advance his or her evaluation of the
application.
(b) The Associate Administrator may dismiss the application without
prejudice if:
(1) He or she determines that there is insufficient information upon
which to base a determination; or
(2) He or she requests additional information from the applicant and
it is not submitted.
[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56
FR 8621, 8622, Feb. 28, 1991; Amdt. 107-38, 61 FR 21098, May 9, 1996]
Sec. 107.209 Determination.
(a) Upon consideration of the application and other relevant
information received, the Associate Administrator issues a
determination.
(b) The determination includes a written statement setting forth the
relevant facts and the legal basis for the determination, and provides
that any person aggrieved thereby may file a petition for
reconsideration with the Associate Administrator.
(c) The Associate Administrator provides a copy of the determination
to the applicant and to any other person who substantially participated
in the proceeding or requested in comments to the docket to be notified
of the determination. A copy of each determination is placed on file in
the public docket. The Associate Administrator will publish the
determination or notice of the determination in the Federal Register.
(d) A determination issued under this section constitutes an
administrative determination as to whether a particular requirement of a
State or political subdivision or Indian tribe is preempted under the
Federal hazardous material transportation law or regulations issued
thereunder. The fact that a determination has not been issued under this
section with respect to a particular requirement of a State or political
subdivision or Indian tribe carries no implication as to whether the
requirement is preempted under the Federal hazardous material
transportation law or regulations issued hereunder.
[Amdt. 107-24, 56 FR 8623, Feb. 28, 1991, as amended by Amdt. 107-25, 57
FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt.
107-38, 61 FR 21098, May 9, 1996]
Sec. 107.211 Petition for reconsideration.
(a) Any person aggrieved by a determination issued under
Sec. 107.209 may file a petition for reconsideration with the Associate
Administrator. The petition must be filed within 20 days of publication
of the determination in the Federal Register.
(b) The petition must contain a concise statement of the basis for
seeking review, including any specific factual or legal error alleged.
If the petition requests consideration of information that was not
previously made available to the Associate Administrator, the petition
must include the reasons why such information was not previously made
available.
(c) The petitioner shall mail a copy of the petition to each person
who participated, either as an applicant or commenter, in the preemption
determination proceeding, accompanied by a statement that the person may
submit comments concerning the petition to the Associate Administrator
within 20 days. The petition filed with the Associate Administrator must
contain a certification that the petitioner has complied with this
paragraph and include the names and addresses of all persons to whom a
copy of the petition was sent. Late-filed comments are considered so far
as practicable.
(d) The Associate Administrator's decision constitutes final agency
action.
[Amdt. 107-25, 57 FR 20428, May 13, 1992, as amended by Amdt. 107-38, 61
FR 21099, May 9, 1996]
Sec. 107.213 Judicial review.
A party to a proceeding under Sec. 107.203(a) may seek review by the
appropriate district court of the United States of a decision of the
Associate Administrator by filing a petition with the court within 60
days after the Associate Administrator's determination
[[Page 27]]
becomes final. The determination becomes final when it is published in
the Federal Register.
[Amdt. 107-38, 61 FR 21099, May 9, 1996]
Waiver of Preemption Determinations
Sec. 107.215 Application.
(a) With the exception of requirements preempted under 49 U.S.C.
5125(c), any State or political subdivision thereof, or Indian tribe may
apply to the Associate Administrator for a waiver of preemption with
respect to any requirement that the State or political subdivision
thereof or an Indian tribe acknowledges to be preempted under the
Federal hazardous material transportation law or the regulations issued
thereunder, or that has been determined by a court of competent
jurisdiction to be so preempted. The Associate Administrator may waive
preemption with respect to such requirement upon a determination that
such requirement--
(1) Affords an equal or greater level of protection to the public
than is afforded by the requirements of the Federal hazardous material
transportation law or the regulations issued thereunder, and
(2) Does not unreasonably burden commerce.
(b) Each application filed under this section for a waiver of
preemption determination must:
(1) Be submitted to the Associate Administrator for Hazardous
Materials Safety, Research and Special Programs Administration, U.S.
Department of Transportation, Washington, DC 20590-0001. Attention:
Hazardous Materials Preemption Docket;
(2) Set forth the text of the State or political subdivision
requirement for which the determination is being sought;
(3) Include a copy of any court order and any ruling issued under
Sec. 107.209 having a bearing on the application;
(4) Contain an express acknowledgment by the applicant that the
State, political subdivision, or Indian tribe requirement is preempted
under the Federal hazardous material transportation law or the
regulations issued thereunder, unless it has been so determined by a
court of competent jurisdiction or in a determination issued under
Sec. 107.209;
(5) Specify each requirement of the Federal hazardous material
transportation law or the regulations issued thereunder that preempts
the State, political subdivision, or Indian tribe requirement;
(6) State why the applicant believes the State, political
subdivision or Indian tribe requirements affords an equal or greater
level of protection to the public than is afforded by the requirements
of the Federal hazardous material transportation law or the regulations
issued thereunder;
(7) State why the applicant believes the State, political
subdivision or Indian tribe requirement does not unreasonably burden
commerce; and
(8) Specify what steps the State, political subdivision or Indian
tribe is taking to administer and enforce effectively its inconsistent
requirement.
[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-22, 55
FR 39978, Oct. 1, 1990; Amdt. 107-24, 56 FR 8621, 8623, Feb. 28, 1991;
56 FR 15510, Apr. 17, 1991; Amdt. 107-23, 56 FR 66156, Dec. 20, 1991;
Amdt. 107-25, 57 FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131,
Sept. 26, 1994; Amdt. 107-38, 61 FR 21099, May 9, 1996]
Sec. 107.217 Notice.
(a) The applicant shall mail a copy of the application and any
subsequent amendments or other documents relating to the application to
each person who is reasonably ascertainable by the applicant as a person
who will be affected by the determination sought. The copy of the
application must be accompanied by a statement that the person may
submit comments regarding the application to the Associate Administrator
within 45 days. The application filed with the Associate Administrator
must include a certification that the application has complied with this
paragraph and must include the names and addresses of each person to
whom the application was sent.
(b) Notwithstanding the provisions of paragraph (a) of this section,
if the State or political subdivision determines that compliance with
paragraph
[[Page 28]]
(a) of this section would be impracticable, the applicant shall:
(1) Comply with the requirements of paragraph (a) of this section
with regard to those persons whom it is reasonable and practicable to
notify; and
(2) Include with the application filed with the Associate
Administrator a description of the persons or class or classes of
persons to whom notice was not sent.
(c) The Associate Administrator may require the applicant to provide
notice in addition to that required by paragraphs (a) and (b) of this
section, or may determine that the notice required by paragraph (a) of
the section is not impracticable, or that notice should be published in
the Federal Register. Late-filed comments are considered so far as
practicable.
(d) The Associate Administrator may notify any other persons who may
be affected by the outcome of a determination on the application.
(e) Any person submitting written comments to the Associate
Administrator with respect to an application filed under this section
shall send a copy of the comments to the applicant. The person shall
certify to the Associate Administrator that he has complied with the
requirements of this paragraph. The Associate Administrator may notify
other persons participating in the proceeding of the comments and
provide an opportunity for those other persons to respond.
[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56
FR 8621, Feb. 28, 1991; Amdt. 107-25, 57 FR 20429, May 13, 1992; Amdt.
107-38, 61 FR 21099, May 9, 1996]
Sec. 107.219 Processing.
(a) The Associate Administrator may initiate an investigation of any
statement in an application and utilize in his or her evaluation any
relevant facts obtained by that investigation. The Associate
Administrator may solicit and accept submissions from third persons
relevant to an application and will provide the applicant an opportunity
to respond to all third person submissions. In evaluating an
application, the Associate Administrator on his or her own initiative
may convene a hearing or conference, if he or she considers that a
hearing or conference will advance his or her evaluation of the
application.
(b) The Associate Administrator may dismiss the application without
prejudice if:
(1) He or she determines that there is insufficient information upon
which to base a determination;
(2) Upon his or her request, additional information is not submitted
by the applicant; or
(3) The applicant fails to provide the notice required by
Sec. 107.217.
(c) Except as provided in Sec. 107.201(c), the Associate
Administrator will only consider an application for a waiver of
preemption determination if:
(1) The applicant State or political subdivision thereof or Indian
tribe expressly acknowledges in its application that the State or
political subdivision thereof or Indian tribe requirement for which the
determination is sought is inconsistent with the requirements of the
Federal hazardous material transportation law or the regulations issued
thereunder; or
(2) The State or political subdivision thereof or Indian tribe
requirement has been determined by a court of competent jurisdiction or
in a ruling issued under Sec. 107.209 to be inconsistent with the
requirements of the Federal hazardous material transportation law or the
regulations issued thereunder.
(d) When the Associate Administrator has received all substantive
information it considers necessary to process an application for a
waiver of preemption determination, it serves notice of that fact upon
the applicant and all other persons who received notice of the
proceeding pursuant to Sec. 107.217.
(e) To the extent possible, each application for a waiver of
preemption determination will be acted upon in a manner consistent with
the disposition of previous applications for waiver of preemption
determinations.
[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56
FR 8621, 8623, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994;
Amdt. 107-38, 61 FR 21099, May 9, 1996; 65 FR 58618, Sept. 29, 2000]
[[Page 29]]
Sec. 107.221 Determination.
(a) After considering the application and other relevant information
received or obtained during the proceeding, the Associate Administrator
issues a determination.
(b) The Associate Administrator may issue a waiver of preemption
only on finding that the requirement of the State or political
subdivision thereof or Indian tribe affords the public a level of safety
at least equal to that afforded by the requirements of the Federal
hazardous material transportation law or the regulations issued
thereunder and does not unreasonably burden commerce. In determining if
the requirement of the State or political subdivision thereof or Indian
tribe unreasonably burdens commerce, the Associate Administrator
considers:
(1) The extent to which increased costs and impairment of efficiency
result from the requirement of the State or political subdivision
thereof or Indian tribe.
(2) Whether the requirement of the State or political subdivision
thereof or Indian tribe has a rational basis.
(3) Whether the requirement of the State or political subdivision
thereof or Indian tribe achieves its stated purpose.
(4) Whether there is need for uniformity with regard to the subject
concerned and if so, whether the requirement of the State or political
subdivision thereof or Indian tribe competes or conflicts with those of
other States or political subdivisions thereof or Indian tribes.
(c) The determination includes a written statement setting forth
relevant facts and legal bases and providing that any person aggrieved
by the determination may file a petition for reconsideration with the
Associate Administrator.
(d) The Associate Administrator provides a copy of the determination
to the applicant and to any other person who substantially participated
in the proceeding or requested in comments to the docket to be notified
of the determination. A copy of the determination is placed on file in
the public docket. The Associate Administrator will publish the
determination or notice of the determination in the Federal Register.
(e) A determination under this section constitutes an administrative
finding of whether a particular requirement of a State or political
subdivision thereof or Indian tribe is preempted under the Federal
hazardous material transportation law or any regulation issued
thereunder, or whether preemption is waived.
[Amdt. 107-38, 61 FR 21099, May 9, 1996]
Sec. 107.223 Petition for reconsideration.
(a) Any person aggrieved by a determination under Sec. 107.221 may
file a petition for reconsideration with the Associate Administrator.
The petition must be filed within 20 days of publication of the
determination in the Federal Register.
(b) The petition must contain a concise statement of the basis for
seeking review, including any specific factual or legal error alleged.
If the petition requests consideration of information that was not
previously made available to the Associate Administrator, the petition
must include the reasons why such information was not previously made
available.
(c) The petitioner shall mail a copy of the petition to each person
who participated, either as an applicant or commenter, in the waiver of
preemption proceeding, accompanied by a statement that the person may
submit comments concerning the petition to the Associate Administrator
within 20 days. The petition filed with the Associate Administrator must
contain a certification that the petitioner has complied with this
paragraph and include the names and addresses of all persons to whom a
copy of the petition was sent. Late-filed comments are considered so far
as practicable.
(d) The Associate Administrator's decision constitutes final agency
action.
[Amdt. 107-25, 57 FR 20429, May 13, 1992, as amended by Amdt. 107-38, 61
FR 21099, May 9, 1996]
Sec. 107.227 Judicial review.
A party to a proceeding under Sec. 107.215(a) may seek review by the
appropriate district court of the United States of a decision of the
Associate
[[Page 30]]
Administrator by filing a petition with the court within 60 days after
the Associate Administrator's determination becomes final. The
determination becomes final when it is published in the Federal
Register.
[Amdt. 107-38, 61 FR 21099, May 9, 1996]
Subpart D--Enforcement
Source: Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, unless otherwise
noted.
Sec. 107.301 Delegated authority for enforcement.
Under redelegation from the Administrator, Research and Special
Programs Administration, the Associate Administrator for Hazardous
Materials Safety and the Office of the Chief Counsel exercise their
authority for enforcement of the Federal hazardous material
transportation law, this subchapter, and subchapter C of this
subchapter, in accordance with Sec. 1.53 of this title.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-24, 56
FR 8621, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994]
Sec. 107.303 Purpose and scope.
This subchapter describes the various enforcement authorities
exercised by the Associate Administrator for Hazardous Materials Safety
and the Office of Chief Counsel and the associated sanctions and
prescribes the procedures governing the exercise of those authorities
and the imposition of those sanctions.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51
FR 34986, Oct. 1, 1986; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991]
Sec. 107.305 Investigations.
(a) General. In accordance with its delegated authority under part 1
of this title, the Associate Administrator may initiate investigations
relating to compliance by any person with any provisions of this
subchapter or subchapter C of this chapter, or any exemption, approval,
or order issued thereunder, or any court decree relating thereto. The
Associate Administrator encourages voluntary production of documents in
accordance with and subject to Sec. 107.13, and hearings may be
conducted, and depositions taken pursuant to 49 U.S.C. 5121(a). The
Associate Administrator may conduct investigative conferences and
hearings in the course of any investigation.
(b) Investigations and Inspections. Investigations under 49 U.S.C.
5121(a) are conducted by personnel duly authorized for that purpose by
the Associate Administrator. Inspections under 49 U.S.C. 5121(c) are
conducted by Hazardous Materials Enforcement Specialists, also known as
``hazmat inspectors'' or ``inspectors,'' whom the Associate
Administrator has designated for that purpose.
(1) An inspector will, on request, present his or her credentials
for examination, but the credentials may not be reproduced.
(2) An inspector may administer oaths and receive affirmations in
any matter under investigation by the Associate Administrator.
(3) An inspector may gather information by reasonable means
including, but not limited to, interviews, statements, photocopying,
photography, and video- and audio-recording.
(4) With concurrence of the Director, Office of Hazardous Materials
Enforcement, Research and Special Programs Administration, an inspector
may issue a subpoena for the production of documentary or other tangible
evidence if, on the basis of information available to the inspector, the
documents and evidence materially will advance a determination of
compliance with this subchapter or subchapter C. Service of a subpoena
shall be in accordance with Sec. 107.13 (c) and (d). A person to whom a
subpoena is directed may seek review of the subpoena by applying to the
Office of Chief Counsel in accordance with Sec. 107.13(h). A subpoena
issued under this paragraph may be enforced in accordance with
Sec. 107.13(i).
(c) Notification. Any person who is the subject of an Associate
Administrator investigation and who is requested to furnish information
or documentary evidence is notified as to the general purpose for which
the information or evidence is sought.
(d) Termination. When the facts disclosed by an investigation
indicate that further action is unnecessary or unwarranted at that time,
the person
[[Page 31]]
being investigated is notified and the investigative file is closed
without prejudice to further investigation by the Associate
Administrator.
(e) Confidentiality. Information received in an investigation under
this section, including the identity of the person investigated and any
other person who provides information during the investigation, shall
remain confidential under the investigatory file exception, or other
appropriate exception, to the public disclosure requirements of 5 U.S.C.
552.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-24, 56
FR 8621, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt.
107-38, 61 FR 21099, May 9, 1996; 66 FR 45377, Aug. 28, 2001]
Compliance Orders and Civil Penalties
Sec. 107.307 General.
(a) When the Associate Administrator and the Office of the Chief
Counsel have reason to believe that a person is knowingly engaging or
has knowingly engaged in conduct which is a violation of the Federal
hazardous material transportation law or any provision of this
subchapter or subchapter C of this chapter, or any exemption, or order
issued thereunder, for which the Associate Administrator or the Office
of the Chief Counsel exercise enforcement authority, they may--
(1) Issue a warning letter, as provided in Sec. 107.309;
(2) Initiate proceedings to assess a civil penalty, as provided in
either Secs. 107.310 or 107.311;
(3) Issue an order directing compliance, regardless of whether a
warning letter has been issued or a civil penalty assessed; and
(4) Seek any other remedy available under the Federal hazardous
material transportation law.
(b) In the case of a proceeding initiated for failure to comply with
an exemption, the allegation of a violation of a term or condition
thereof is considered by the Associate Administrator and the Office of
the Chief Counsel to constitute an allegation that the exemption holder
or party to the exemption is failing, or has failed to comply with the
underlying regulations from which relief was granted by the exemption.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-32, 59
FR 49131, Sept. 26, 1994; Amdt. 107-36, 61 FR 7183, Feb. 26, 1996; 66 FR
45377, Aug. 28, 2001]
Sec. 107.309 Warning letters.
(a) The Associate Administrator may issue a warning letter to any
person whom the Associate Administrator believes to have committed a
probable violation of the Federal hazardous material transportation law
or any provision of this subchapter, subchapter C of this chapter, or
any exemption issued thereunder.
(b) A warning letter issued under this section includes:
(1) A statement of the facts upon which the Associate Administrator
bases its determination that the person has committed a probable
violation;
(2) A statement that the recurrence of the probable violations cited
may subject the person to enforcement action; and
(3) An opportunity to respond to the warning letter by submitting
pertinent information or explanations concerning the probable violations
cited therein.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51
FR 34986, Oct. 1, 1986; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; Amdt.
107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 107-36, 61 FR 7183, Feb. 26,
1996; 66 FR 45377, Aug. 28, 2001]
Sec. 107.310 Ticketing.
(a) For an alleged violation that does not have a direct or
substantial impact on safety, the Associate Administrator may issue a
ticket.
(b) The Associate Administrator issues a ticket by mailing it by
certified or registered mail to the person alleged to have committed the
violation. The ticket includes:
(1) A statement of the facts on which the Associate Administrator
bases the conclusion that the person has committed the alleged
violation;
(2) The maximum penalty provided for by statute, the proposed full
penalty determined according to RSPA's civil penalty guidelines and the
statutory criteria for penalty assessment, and the ticket penalty
amount; and
[[Page 32]]
(3) A statement that within 45 days of receipt of the ticket, the
person must pay the penalty in accordance with paragraph (d) of this
section, make an informal response under Sec. 107.317, or request a
formal administrative hearing under Sec. 107.319.
(c) If the person makes an informal response or requests a formal
administrative hearing, the Associate Administrator forwards the
inspection report, ticket and response to the Office of the Chief
Counsel for processing under Secs. 107.307-107.339, except that the
Office of the Chief Counsel will not issue a Notice of Probable
Violation under Sec. 107.311. The Office of the Chief Counsel may impose
a civil penalty that does not exceed the proposed full penalty set forth
in the ticket.
(d) Payment of the ticket penalty amount must be made in accordance
with the instructions on the ticket.
(e) If within 45 days of receiving the ticket the person does not
pay the ticket amount, make an informal response, or request a formal
administrative hearing, the person has waived the right to make an
informal response or request a hearing, has admitted the violation and
owes the ticket penalty amount to RSPA.
[Amdt. 107-36, 61 FR 7183, Feb. 26, 1996, as amended at 66 FR 45377,
Aug. 28, 2001]
Sec. 107.311 Notice of probable violation.
(a) The Office of Chief Counsel may serve a notice of probable
violation on a person alleging the violation of one or more provisions
of the Federal hazardous material transportation law or any provision of
this subchapter or subchapter C of this chapter, or any exemption, or
order issued thereunder.
(b) A notice of probable violation issued under this section
includes the following information:
(1) A citation of the provisions of the Federal hazardous material
transportation law, an order issued thereunder, this subchapter,
subchapter C of this chapter, or the terms of any exemption issued
thereunder which the Office of Chief Counsel believes the respondent is
violating or has violated.
(2) A statement of the factual allegations upon which the demand for
remedial action, a civil penalty, or both, is based.
(3) A statement of the respondent's right to present written or oral
explanations, information, and arguments in answer to the allegations
and in mitigation of the sanction sought in the notice of probable
violation.
(4) A statement of the respondent's right to request a hearing and
the procedures for requesting a hearing.
(5) In addition, in the case of a notice of probable violation
proposing a compliance order, a statement of the proposed actions to be
taken by the respondent to achieve compliance.
(6) In addition, in the case of a notice of probable violation
proposing a civil penalty:
(i) A statement of the maximum civil penalty for which the
respondent may be liable;
(ii) The amount of the preliminary civil penalty being sought by the
Office of Chief Counsel, constitutes the maximum amount the Chief
Counsel may seek throughout the proceeding; and
(iii) A description of the manner in which the respondent makes
payment of any money due the United States as a result of the
proceeding.
(c) The Office of Chief Counsel may amend a notice of probable
violation at any time before issuance of a compliance order or an order
assessing a civil penalty. If the Office of Chief Counsel alleges any
new material facts or seeks new or additional remedial action or an
increase in the amount of the proposed civil penalty, it issues a new
notice of probable violation under this section.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 50 FR 45730,
Nov. 1, 1985; Amdt. 107-24, 56 FR 8624, Feb. 28, 1991; Amdt. 107-32, 59
FR 49131, Sept. 26, 1994; Amdt. 107-35, 60 FR 49108, Sept. 21, 1995;
Amdt. 107-36, 61 FR 7184, Feb. 26, 1996]
Sec. 107.313 Reply.
(a) Within 30 days of receipt of a notice of probable violation, the
respondent must either:
(1) Admit the violation under Sec. 107.315;
(2) Make an informal response under Sec. 107.317; or
(3) Request a hearing under Sec. 107.319.
(b) Failure of the respondent to file a reply as provided in this
section constitutes a waiver of the respondent's
[[Page 33]]
right to appear and contest the allegations and authorizes the Chief
Counsel, without further notice to the respondent, to find the facts to
be as alleged in the notice of probable violation and issue an order
directing compliance or assess a civil penalty, or, if proposed in the
notice, both. Failure to request a hearing under paragraph (a)(3) of
this section constitutes a waiver of the respondent's right to a
hearing.
(c) Upon the request of the respondent, the Office of Chief Counsel
may, for good cause shown and filed within the 30 days prescribed in the
notice of probable violation, extend the 30-day response period.
Sec. 107.315 Admission of violations.
(a) In responding to a notice of probable violation issued under
Sec. 107.311, the respondent may admit the alleged violations and agree
to accept the terms of a proposed compliance order or to pay the amount
of the preliminarily assessed civil penalty, or, if proposed in the
notice, both.
(b) If the respondent agrees to the terms of a proposed compliance
order, the Chief Counsel issues a final order prescribing the remedial
action to be taken by the respondent.
(c) Payment of a civil penalty, when the amount of the penalty
exceeds $10,000, must be made by wire transfer, through the Federal
Reserve Communications System (Fedwire), to the account of the U.S.
Treasury. Detailed instructions on making payments by wire transfer may
be obtained from the Financial Operations Division (AMZ-320), Federal
Aviation Administration, Mike Monroney Aeronautical Center, P.O. Box
25880, Oklahoma City, OK 73125.
(d) Payment of a civil penalty, when the amount of the penalty is
$10,000 or less, must be made either by wire transfer, as set forth in
paragraph (c) of this section, or certified check or money order payable
to ``U.S. Department of Transportation'' and submitted to the Financial
Operations Division (AMZ-320), Federal Aviation Administration, Mike
Monroney Aeronautical Center, P.O. Box 25880, Oklahoma City, OK 73125.
[Amdt. 107-11, 48 FR 265l, Jan. 20, 1983, as amended by Amdt. 107-23, 57
FR 45453, Oct. 1, 1992; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; Amdt.
107-38, 61 FR 21100, May 9, 1996]
Sec. 107.317 Informal response.
(a) In responding to a notice of probable violation under
Sec. 107.311, the respondent may submit to the official who issued the
notice, written explanations, information, or arguments in response to
the allegations, the terms of a proposed compliance order, or the amount
of the preliminarily assessed civil penalty.
(b) The respondent may include in his informal response a request
for a conference. Upon the request of the respondent, the conference may
be either in person or by telephone. A request for a conference must set
forth the issues the respondent will raise at the conference.
(c) Upon receipt of a request for a conference under paragraph (b)
of this section, the Chief Counsel's Office, in consultation with the
Associate Administrator, arranges for a conference as soon as
practicable at a time and place of mutual convenience.
(d) The respondent's written explanations, information, and
arguments as well as the respondent's presentation at a conference are
considered by the Chief Counsel in reviewing the notice of probable
violation. Based upon a review of the proceeding, the Chief Counsel may
dismiss the notice of probable violation in whole or in part. If he does
not dismiss it in whole, he issues an order directing compliance or
assessing a civil penalty, or, if proposed in the notice, both.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-23, 56
FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]
Sec. 107.319 Request for a hearing.
(a) In responding to a notice of probable violation under
Sec. 107.311, the respondent may request a formal administrative hearing
on the record before an Administrative Law Judge (ALJ) obtained by the
Office of the Chief Counsel.
[[Page 34]]
(b) A request for a hearing under paragraph (a) of this section
must:
(1) State the name and address of the respondent and of the person
submitting the request if different from the respondent;
(2) State which allegations of violations, if any, are admitted; and
(3) State generally the issues to be raised by the respondent at the
hearing. Issues not raised in the request are not barred from
presentation at the hearing; and
(4) Be addressed to the official who issued the notice.
(c) After a request for a hearing that complies with the
requirements of paragraph (b) of this section, the Chief Counsel obtains
an ALJ to preside over the hearing and notifies the respondent of this
fact. Upon assignment of an ALJ, further matters in the proceeding
generally are conducted by and through the ALJ, except that the Chief
Counsel and respondent may compromise or settle the case under
Sec. 107.327 of this subpart without order of the ALJ or voluntarily
dismiss the case under Rule 41(a)(1) of the Federal Rules of Civil
Procedure without order of the ALJ; in the event of such a compromise,
settlement or dismissal, the Chief Counsel expeditiously will notify the
ALJ thereof.
(d) At any time after requesting a formal administrative hearing but
prior to the issuance of a decision and final order by the ALJ, the
respondent may withdraw such request in writing, thereby terminating the
jurisdication of the ALJ in the case. Such a withdrawal constitutes an
irrevocable waiver of respondent's right to such a hearing on the facts,
allegations, and proposed sanction presented in the notice of probable
violation to which the request for hearing relates.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 48 FR 17094,
Apr. 21, 1983; Amdt. No. 107-19, 54 FR 22899, May 30, 1989]
Sec. 107.321 Hearing.
(a) To the extent practicable, the hearing is held in the general
vicinity of the place where the alleged violation occurred or at a place
convenient to the respondent. Testimony by witnesses shall be given
under oath and the hearing shall be recorded verbatim.
(b) Hearings are conducted in accordance with the Federal Rules of
Evidence and Federal Rules of Civil Procedure; however, the ALJ may
modify them as he determines necessary in the interest of a full
development of the facts. In addition, the ALJ may:
(1) Administer oaths and affirmations;
(2) Issue subpoenas as provided by Sec. 107.13;
(3) Adopt procedures for the submission of motions, evidence, and
other documents pertinent to the proceeding;
(4) Take or cause depositions to be taken;
(5) Rule on offers of proof and receive relevant evidence;
(6) Examine witnesses at the hearing;
(7) Convene, recess, reconvene, adjourn and otherwise regulate the
course of the hearing;
(8) Hold conferences for settlement, simplification of the issues,
or any other proper purpose; and
(9) Take any other action authorized by, or consistent with, the
provisions of this subpart and permitted by law which may expedite the
hearing or aid in the disposition of an issue raised therein.
(c) The official who issued the notice of probable violation, or his
representative, has the burden of proving the facts alleged therein.
(d) The respondent may appear and be heard on his own behalf or
through counsel of his choice. The respondent or his counsel may offer
relevant information including testimony which he believes should be
considered in opposition to the allegations or which may bear on the
sanction being sought and conduct such cross-examination as may be
required for a full disclosure of the facts.
Sec. 107.323 ALJ's decision.
(a) After consideration of all matters of record in the proceeding,
the ALJ shall issue an order dismissing the notice of probable violation
in whole or in part or granting the sanction sought by the Office of
Chief Counsel in the notice. If the ALJ does not dismiss the notice of
probable violation in whole, he issues an order directing compliance
[[Page 35]]
or assessing a civil penalty, or, if proposed in the notice, both. The
order includes a statement of the findings and conclusions, and the
reasons therefore, on all material issues of fact, law, and discretion.
(b) If, within 20 days of receipt of an order issued under paragraph
(a) of this section, the respondent does not submit in writing his
acceptance of the terms of an order directing compliance, or, where
appropriate, pay a civil penalty, or file an appeal under Sec. 107.325,
the case may be referred to the Attorney General with a request that an
action be brought in the appropriate United States District Court to
enforce the terms of a compliance order or collect the civil penalty.
Sec. 107.325 Appeals.
(a) Hearing proceedings. A party aggrieved by an ALJ's decision and
order issued under Sec. 107.323, may file a written appeal in accordance
with paragraph (c) of this section with the Administrator, Research and
Special Programs Administration (RSPA), 400 Seventh Street, SW.,
Washington, DC 20590-0001.
(b) Non-Hearing proceedings. A respondent aggrieved by an order
issued under Sec. 107.317, may file a written appeal in accordance with
paragraph (c) of this section with the Administrator, RSPA, 400 Seventh
Street, SW., Washington, DC 20590-0001.
(c) An appeal of an order issued under this subpart must:
(1) Be filed within 20 days of receipt of the order by the appealing
party; and
(2) State with particularity the findings in the order that the
appealing party challenges, and include all information and arguments
pertinent thereto.
(d) If the Administrator, RSPA, affirms the order in whole or in
part, the respondent must comply with the terms of the decision within
20 days of the respondent's receipt thereof, or within the time
prescribed in the order. If the respondent does not comply with the
terms of the decision within 20 days of receipt, or within the time
prescribed in the order, the case may be referred to the Attorney
General for action to enforce the terms of the decision.
(e) The filing of an appeal stays the effectiveness of an order
issued under Sec. 107.317 or Sec. 107.323. However, if the
Administrator, RSPA, determines that it is in the public interest, he
may keep an order directing compliance in force pending appeal.
[][Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 50 FR 45730,
Nov. 1, 1985; Amdt. 107-22, 55 FR 39978, Oct. 1, 1990]
Sec. 107.327 Compromise and settlement.
(a) At any time before an order issued under Sec. 107.317 or
Sec. 107.323 is referred to the Attorney General for enforcement, the
respondent or the Office of Chief Counsel may propose a compromise as
follows:
(1) In civil penalty cases, the respondent or Chief Counsel may
offer to compromise the amount of the penalty by submitting an offer for
a specific amount to the other party. An offer of compromise by the
respondent shall be submitted to the Chief Counsel who may, after
consultation with the Associate Administrator, accept or reject it.
(i) A compromise offer stays the running of any response period then
outstanding.
(ii) If a compromise is agreed to by the parties, the respondent is
notified in writing. Upon receipt of payment by Office of Chief Counsel,
the respondent is notified in writing that acceptance of payment is in
full satisfaction of the civil penalty proposed or assessed, and Office
of Chief Counsel closes the case with prejudice to the respondent.
(iii) If a compromise cannot be agreed to, the respondent is
notified in writing and is given 10 days or the amount of time remaining
in the then outstanding response period, whichever is longer, to respond
to whatever action was taken by the Office of Chief Counsel or the
Administrator, RSPA.
(2) In compliance order cases, the respondent may propose a consent
agreement to the Chief Counsel. If the Chief Counsel accepts the
agreement, he issues an order in accordance with its terms. If the Chief
Counsel rejects the
[[Page 36]]
agreement, he directs that the proceeding continue. An agreement
submitted to the Chief Counsel must include:
(i) A statement of any allegations of fact which the respondent
challenges;
(ii) The reasons why the terms of a compliance order or proposed
compliance order are or would be too burdensome for the respondent, or
why such terms are not supported by the record in the case;
(iii) A proposed compliance order suitable for issuance by the Chief
Counsel;
(iv) An admission of all jurisdictional facts; and
(v) An express waiver of further procedural steps and all right to
seek judicial review or otherwise challenge or contest the validity of
the order.
(b) Notwithstanding paragraph (a)(1) of this section, the respondent
or Office of Chief Counsel may propose to settle the case. If the Chief
Counsel agrees to a settlement, the respondent is notified and the case
is closed without prejudice to the respondent.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 50 FR 45730,
Nov. 1, 1985; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; 56 FR 15510, Apr.
17, 1991; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; 66 FR 45377, Aug. 28,
2001]
Sec. 107.329 Maximum penalties.
(a) A person who knowingly violates a requirement of the Federal
hazardous material transportation law, an order issued thereunder, this
subchapter, subchapter C of this chapter, or an exemption issued under
this subchapter applicable to the transporting of hazardous materials or
the causing of them to be transported or shipped is liable for a civil
penalty of not more than $25,000 ($27,500 for a violation occurring
after January 21, 1997) and not less than $250 for each violation. When
the violation is a continuing one, each day of the violation constitutes
a separate offense.
(b) A person who knowingly violates a requirement of the Federal
hazardous material transportation law, an order issued thereunder, this
subchapter, subchapter C of this chapter, or an exemption issued under
this subchapter applicable to the manufacture, fabrication, marking,
maintenance, reconditioning, repair, or testing of a packaging or
container which is represented, marked, certified or sold by that person
as being qualified for use in the transportation of hazardous materials
in commerce is liable for a civil penalty of not more than $25,000
($27,500 for a violation occurring after January 21, 1997) and not less
than $250 for each violation.
[Amdt. 107-24, 56 FR 8624, Feb. 28, 1991, as amended by Amdt. 107-32, 59
FR 49131, Sept. 26, 1994; Amdt. 17-40, 62 FR 2971, Jan. 21, 1997; 65 FR
58618, Sept. 29, 2000]
Sec. 107.331 Assessment considerations.
After finding a knowing violation under this subpart, the Office of
Chief Counsel assesses a civil penalty taking the following into
account:
(a) The nature and circumstances of the violation;
(b) The extent and gravity of the violation;
(c) The degree of the respondent's culpability;
(d) The respondent's prior violations;
(e) The respondent's ability to pay;
(f) The effect on the respondent's ability to continue in business;
and
(g) Such other matters as justice may require.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-30, 58
FR 50500, Sept. 27, 1993; Amdt. 107-38, 61 FR 21100, May 9, 1996]
Criminal Penalties
Sec. 107.333 Criminal penalties generally.
A person who knowingly violates Sec. 171.2(g) or willfully violates
a provision of the Federal hazardous material transportation law or an
order or regulation issued thereunder shall be fined under title 18,
United States Code, or imprisoned for not more than 5 years, or both.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-32, 59
FR 49131, Sept. 26, 1994]
Sec. 107.335 Referral for prosecution.
If the Associate Administrator becomes aware of a possible willful
violation of the Federal hazardous material transportation law, this
subchapter, subchapter C of this chapter, or any exemption, or order
issued thereunder,
[[Page 37]]
for which the Associate Administrator exercises enforcement
responsibility, it shall report it to the Office of the Chief Counsel,
Research and Special Programs Administration, U.S. Department of
Transportation, Washington, DC 20590-0001. If appropriate, the Chief
Counsel refers the report to the Department of Justice for criminal
prosecution of the offender.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-22, 55
FR 39978, Oct. 1, 1990; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; 56 FR
15510, Apr. 17, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt.
107-35, 60 FR 49108, Sept. 21, 1995; 66 FR 45377, Aug. 28, 2001]
Sec. 107.336 Limitation on fines and penalties.
If a State or political subdivision or Indian tribe assesses any
fine or penalty determined by the Secretary to be appropriate for a
violation concerning a subject listed in Sec. 107.202(a), no additional
fine or penalty may be assessed for such violation by any other
authority.
[Amdt. 107-24, 56 FR 8624, Feb. 28, 1991]
Injunctive Action
Sec. 107.337 Injunctions generally.
Whenever it appears to the Office of Chief Counsel that a person has
engaged, or is engaged, or is about to engage in any act or practice
constituting a violation of any provision of the Federal hazardous
material transportation law, this subchapter, subchapter C of this
chapter, or any exemption, or order issued thereunder, for which the
Office of Chief Counsel exercises enforcement responsibility, the
Administrator, RSPA, or his delegate, may request the Attorney General
to bring an action in the appropriate United States District Court for
such relief as is necessary or appropriate, including mandatory or
prohibitive injunctive relief, interim equitable relief, and punitive
damages as provided by 49 U.S.C. 5122(a).
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-32, 59
FR 49131, Sept. 26, 1994]
Sec. 107.339 Imminent hazards.
Whenever it appears to the Office of the Chief Counsel that there is
a substantial likelihood that death, serious illness, or severe personal
injury will result from the transportation of a particular hazardous
material or hazardous materials container, before a compliance order
proceeding or other administrative hearing or formal proceeding to abate
the risk of that harm can be completed, the Administrator, RSPA, or his
delegate, may bring an action under 49 U.S.C. 5122(b) in the appropriate
United States District Court for an order suspending or restricting the
transporation of that hazardous material or those containers or for such
other equitable relief as is necessary or appropriate to ameliorate the
hazard.
[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51
FR 34987, Oct. 1, 1986; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994]
Appendix A to Subpart D of Part 107--Guidelines for Civil Penalties
I. This appendix sets forth the guidelines used by the Office of
Hazardous Materials Safety (as of January 18, 1995) in making initial
baseline determinations for recommending civil penalties. The first part
of these guidelines is a list of baseline amounts or ranges for probable
violations frequently cited in enforcement reports referred for action.
Following the list of violations are general guidelines used by OHMS in
making initial penalty determinations in enforcement cases.
II. List of Frequently Cited Violations
------------------------------------------------------------------------
Violation description Section or cite Baseline assessment
------------------------------------------------------------------------
PART 107--REQUIREMENTS
------------------------------------------------------------------------
Failure to register as a 107.608............. $1,000 +, $500 each
carrier or shipper of add'l year.
hazardous material.
------------------------------------------------------------------------
PART 171--REQUIREMENTS
------------------------------------------------------------------------
Failure to give immediate 171.15.............. $3,000.
telephone notice of a
reportable hazardous
materials incident.
[[Page 38]]
Failure to file a DOT 5800.1 171.16.............. $500 to $2,500.
Hazardous Materials
Incident Report within 30
days following an
unintentional release of
hazardous materials in
transportation.
------------------------------------------------------------------------
PART 172--REQUIREMENTS
------------------------------------------------------------------------
Shipping Papers (Sec.
172.200--172.205):
Failure to execute a 172.201............. $3,000 to $6,000.
shipping paper for a
shipment of hazardous
materials.
Failure to follow one or 172.201(a)(1)....... $1,200.
more of the three
approved formats for
listing hazardous
materials on a shipping
paper.
Failure to include a 172.202............. $800 to $1,600.
proper shipping name in
the shipping
description or using an
incorrect proper
shipping name.
Failure to include a 172.202............. $1,000 to $2,000.
hazard class/division
number in the shipping
description.
Using an incorrect 172.202.............
hazard class/
identification number.
--that does not .................... $800.
affect
compatibility
requirements.
--that affects .................... $3,000 to $6,000.
compatibility
requirements.
Failure to include an 172.202............. $1,000 to $2,000.
identification number
in the shipping
description.
Using an incorrect 172.202.............
identification number.
--that does not .................... $800.
change the response
information.
--that changes the .................... $3,000 to $6,000.
response
information.
Using a shipping 172.202............. $800.
description that
includes additional
unauthorized
information (extra or
incorrect words).
Using a shipping 172.202............. $500.
description not in
required sequence.
Using a shipping 172.202.............
description with two or
more required elements
missing or incorrect.
--such that the .................... $3,000.
material is
misdescribed.
--such that the .................... $6,000.
material is
misclassified.
Failure to include the 172.202(c).......... $400.
total quantity of
hazardous material
covered by a shipping
description.
The letters ``RQ'' are 172.203(c)(2)....... $500.
not used in the
shipping description to
identify materials that
are hazardous
substances.
Using a shipping 172.203(d).......... $2,000 to $4,000.
description for Class 7
(radioactive) material
that fails to contain
the required additional
entries, or contains
incorrect information
for these additional
entries.
Failure to include a 172.203(k).......... $1,000.
required technical name
in parentheses for a
listed generic or
``nos'' material.
Failure to list an 172.203(a).......... $800.
exemption number in
association with the
shipping description.
Failure to include the 172.204(a).......... $1,000.
required shipper's
certification on a
shipping paper.
Failure to execute the 172.204............. $800.
required shipper's
certification on a
shipping paper.
Emergency Response
Information Requirements
(Sec. 172.600--172.604):
1. Providing or listing 172.602.............
incorrect emergency
response information
with or on a shipping
paper.
a. No significant .................... $800.
difference in
response.
b. Ssignificant .................... $3,000 to $6,000.
difference in
response.
2. Failure to include an 172.604............. $2,600.
emergency response
telephone number on a
shipping paper.
3. Failure to have the 172.604............. $1,300.
emergency response
telephone number
monitored while a
hazardous material is
in transportation or
listing multiple
telephone numbers
(without specifying the
times for each) that
are not monitored 24
hours a day.
4. Listing an 172.604............. $2,600 to $4,200.
unauthorized emergency
response telephone
number on a shipping
paper.
5. Listing an incorrect 172.604............. $1,300.
or non-working
emergency response
telephone number on a
shipping paper.
6. Failure to provide 172.604............. $1,300.
required technical
information when the
listed emergency
response telephone
number is contacted.
Package Marking Requirements
(Sec. 172.300--172.338):
Failure to mark the 172.301(a).......... $800 to $1,600.
proper shipping name on
a package or marking an
incorrect shipping name
on a package.
Failure to mark the 172.301(a).......... $1,000 to $2,000.
identification number
on a package.
Marking a package with 172.301(a)..........
an incorrect
identification number.
--that does not .................... $800.
change the response
information.
--that changes the .................... $3,000 to $6,000.
response
information.
Failure to mark the 172.301(a).......... $3,000 to $6,000.
proper shipping name
and identification
number on a package.
Marking a package with 172.301(a)..........
an incorrect shipping
name and identification
number.
--that does not .................... $1,500 to $3,000.
change the response
information.
--that changes the .................... $3,000 to $6,000.
response
information.
Failure to include the 172.301(c).......... $1,000.
required technical
name(s) in parentheses
for a listed generic or
``no'' entry.
Failure to mark a 172.312............. $2,500 to $3,500.
package containing
liquid hazardous
materials with required
orientation marks.
[[Page 39]]
Package Labeling
Requirements (Sec. 172.400-
172.450):
Failure to label a 172.400............. $5,000.
package.
Placing a label that 172.400............. $5,000.
represents a hazard
other than the hazard
presented by the
hazardous material in
the package.
Placing a label on a 172.401(a).......... $800.
package that does not
contain a hazardous
material.
Placing a label on Class 172.403............. $5,000.
7 (radioactive)
material that
understates the proper
label category.
Placing a label on Class 172.403(g).......... $2,000 to $4,000.
7 (radioactive)
material that fails to
contain, or has
erroneous, entries for
the name of the
radionuclide(s),
activity, and transport
index.
Placing a label not 172.407(c).......... $800.
conforming to size
requirements on a
package.
Placing a label on a 172.406(a).......... $800.
different surface of
the package than, or
far away from, the
proper shipping name.
Placing a label that 172.407(d).......... $600 to $2,500.
does not meet color
specification
requirements on a
package (depending on
the variance).
Failure to place a 172.402............. $500 to $2,500.
required subsidiary
label on a package.
Failure to provide an 172.411............. $2,500.
appropriate class or
division number on a
label.
Placarding Requirements
(Sec. 172.500-172.560):
Failure to properly 172.504............. $1,000 to $9,000.
placard a freight
container or vehicle
containing hazardous
materials when table 1
is applicable.
Failure to properly 172.504............. $800 to $7,500.
placard a freight
container or vehicle
containing hazardous
materials when table 2
is applicable.
Training Requirements (Sec.
172.700-172.704):
Failure to train hazmat 172.702.............
employees in the three
required areas of
training.
--more than 10 .................... $2,400 and up.
hazmat employees.
--10 hazmat .................... $1,500 and up.
employees or less.
Failure to train hazmat 172.702.............
employees in any one of
the three required
areas of training.
--more than 10 .................... $800 and up.
hazmat employees.
--10 hazmat .................... $500 and up.
employees or less.
Failure to maintain 172.704.............
training records.
--more than 10 .................... 800 and up.
hazmat employees.
--10 hazmat .................... $500 and up.
employees or less.
------------------------------------------------------------------------
PART 173--REQUIREMENTS
------------------------------------------------------------------------
Overpack Requirements (Sec.
173.25)
Failure to mark an 173.25(a)(4)........ $3,000.
overpack with a
statement indicating
that the inside
packages comply with
prescribed
specifications when
specification packaging
is required.
Reconditioner Requirements
(Sec. 173.28):
1. Representing, 173.28(c), (d)...... $6,000 to $10,800.
marking, or certifying
a drum as a
reconditioned UN
standard packaging,
when the drum did not
meet a UN standard.
2. Marking an incorrect 173.28(b)(2)(ii)....
registration number on
a reconditioned
packaging.
a. Incorrect number. .................... $800.
b. Use of another .................... $7,200.
reconditioner's
number.
3. Failure to properly 173.28(b)(2)(i).....
conduct alternate
leakage test.
a. Improper test.... .................... $2,000.
b. No test at all... .................... $4,000.
4. Representing, 173.28(d)........... $500.
marking, or certifying
a drum as altered from
one standard to
another, when the drum
had not actually been
altered.
Representing, marking, 173.28(d)........... $500.
or certifying a drum as
altered from one
standard to another,
when the drum had not
actually been altered.
Portable and IM Tank
Requirements (Secs.
173.32(e), 173.32c,
173.315)
Offering hazardous 173.32(a)(1), $3,500 to $7,000.
materials for 173.315(a),
transportation in a DOT Applicable
specification or Exemption.
exemption portable tank
which is out of test.
Offering an IM portable 173.32c(c).......... $3,500.
tank for transportation
that has not been
hydrostatically tested
within the last 2\1/2\
years per 173.32b(a).
Offering an IM portable 173.32c(c).......... $3,500.
tank for transportation
that has not been
visually inspected in
last five years per
173.32b(b).
Offering an IM portable 173.32c(c).......... $7,000.
tank for transportation
that has not been
visually or
hydrostatically tested
as required, or failing
to remove the safety
relief valves during
testing.
Offering a hazardous 173.32c(g)..........
material for
transportation in an IM
portable tank equipped
with bottom outlets,
when the material
contained is prohibited
from being offered in
this type of packaging.
--Packing Group II.. .................... $7,000.
--Packing Group III. .................... $5,000.
Failure to provide the 173.32c(k).......... $6,000 to $12,000.
required outage for a
shipment of hazardous
materials, that results
in the release of
hazardous materials.
Offering a hazardous 173.32(e)(3), $3,000.
material for 173.32b(d).
transportation in an
DOT, exemption, or IM
portable tank which
fails to bear markings
that it has been
properly retested.
[[Page 40]]
Cylinder Retesters (Secs.
173.23, 173.34, and
173.302):
Failure to remark as DOT 173.23(c)........... $600.
3AL an aluminum
cylinder manufactured
under a former
exemption.
Certifying or marking as 173.34.............. $800.
retested a
nonspecification
cylinder.
Marking a cylinder in or 173.34(c)(1)........ $6,000 to $10,800.
on the sidewall area
when not permitted by
the applicable
specification.
Failure to maintain 173.34(c)........... $800.
legible markings on a
cylinder.
Failure to perform 173.34(e)........... $2,100 to $5,200.
hydrostatic retesting
at the minimum of 5/3
times the service
pressure, or at the
minimum specified test
pressure.
Failure to conduct a 173.34(e)(3)........ $2,100 to $5,200.
complete visual
external and internal
examination.
Failure to have a 173.34(e)(2)(i)..... $4,000.
retester's
identification number
(RIN).
Failure to have current 173.34)(e)(2)(i).... $2,000.
authority due to
failure to renew a
retester's
identification number.
Failure to have a 173.34(e)(2)(i)..... $7,200.
retester's
identification number
and marking another RIN
on a cylinder.
Marking a RIN before 173.34(e)(1)(ii).... $800.
successfully completing
a hydrostatic retest.
Requalifying a DOT 173.34(e)(1)(ii).... $4,200 to $10,400.
cylinder without
performing the visual
inspection or
hydrostatic retest.
Performing hydrostatic 173.34(e)(4)........ $2,100 to $5,200.
retesting without
demonstrating the
accuracy of the testing
equipment.
Failure to hold 173.34(e)(4)........ $3,100.
hydrostatic test
pressure for 30 seconds
or sufficiently longer
to allow for complete
expansion.
Failure to perform a 173.34(e)(4)........ $3,100.
second retest, after
equipment failure, at a
pressure of 10% more or
100 psi more, whichever
is less (includes
exceeding 90% of test
pressure prior to
conducting a retest).
Failure to condemn a 173.34(e)(6)........ $10,000.
cylinder with permanent
expansion of 10% or
greater (5% for certain
exemption cylinders);
failure to condemn
cylinders with evidence
of internal or external
corrosion, denting,
bulging, or rough usage.
Marking an FRP cylinder Applicable Exemption $6,000 to $10,800.
with steel stamps in
the FRP area of the
cylinder such that the
integrity of the
cylinder is compromised.
Failure to keep complete
and accurate records of
cylinder reinspection
and retest.
--No records kept... .................... $4,000.
--Incomplete or 173.34(e)(8)........ $1,000 to $3,000.
inaccurate records.
Improper marking of the 173.34(e)(7)........ $800
RIN or retest date on a
cylinder.
Marking a DOT 3HT 173.34(e)(15)....... $6,000 to $10,800.
cylinder with a steel
stamp other than a low-
stress steel stamp.
Marking a ``+'' sign on 173.302(c)(3)....... $3,000 to $4,000.
a cylinder without
determining the average
or maximum wall stress,
by calculation or
reference to CGA
Pamphlet C-5.
Representing, marking, 171.2(c), Applicable $2,000 to $6,000.
or certifying a Exemption.
cylinder as meeting the
requirements of an
exemption, when the
cylinder was not
maintained or retested
in accordance with the
exemption.
Rebuilder Requirements (Sec.
173.34):
Representing a DOT-4 173.34(l)........... $6,000 to $10,800.
series cylinder as
meeting the
requirements of the
Hazardous Materials
Regulations without
being authorized to do
so by the Associate
Administrator for
Hazardous Materials
Safety.
Offeror Requirements
(General):
Offering a hazardous Various.............
material for
transportation in an
unauthorized non-UN
standard or
nonspecification
packaging (includes the
failure to comply with
the terms of an
exemption authorizing
the use of a
nonstandard or
nonspecification
packaging).
--Packing Group I .................... $9,000.
(includes Sec. 172
504 table 1
materials).
--Packing Group II.. .................... $7,000.
--Packing Group III. .................... $5,000.
Offering a hazardous 178.3(a), 178.503(a) $3,600.
material for
transportation in a
packaging that has
successfully been
tested to an applicable
UN standard, but is not
marked with the
required UN marking.
Offering a hazardous 173.24(b)...........
material for
transportation in a
packaging that leaks
during conditions
normally incident to
transportation.
--Packing Group I .................... $12,000.
(includes Sec.
172.504 table 2
materials).
--Packing Group II.. .................... $9,000.
--Packing Group III. .................... $6,000.
Overfilling a package so 173.24(b)...........
that the effectiveness
is substantially
reduced.
--Packing Group I .................... $9,000.
(includes Sec.
172.504 table 1
materials).
--Packing Group II.. .................... $6,000.
--Packing Group III. .................... $3,000.
Offering a hazardous 171.14..............
material for
transportation after
October 1, 1996, in an
unauthorized non-UN
standard packaging
marked as manufactured
to a DOT specification.
--packaging meets .................... $3,000.
DOT specification.
--packaging does not .................... $5,000 to $9,000.
meet DOT
specification.
[[Page 41]]
Offeror Requirements (Class
1--Explosives):
Failing to mark the 172.320............. $1,200.
``EX'' approval number
on a package containing
an explosive.
Offering an unapproved 173.54 and 173.56(b)
explosive for
transportation.
--Div 1.3 & 1.4 .................... $5,0000 to $10,000.
fireworks meeting
the chemistry
requirements (both
quantity and type)
of APA Standard 87-
1.
--all other .................... $10,000 to $27,500.
explosives
(including
forbidden
explosives).
Offering a leaking or 173.54(c)........... $10,000 to $27,500.
damaged package of
explosives for
transportation.
Offeror Requirements (Class
7--Radioactive Materials):
1. Offering a DOT 173.415(a), 173.461.
specification 7A
packaging without
maintaining complete
documentation of tests
and an engineering
evaluation or
comparative data.
a. Tests and .................... $8,400.
evaluation not
performed.
b. Complete records .................... $2,000 to $5,000.
not maintained.
2. Offering a Type B 173.471(a)..........
packaging without
holding a valid NRC
approval certificate.
a. Never having .................... $2,500.
obtained one.
b. Holding an .................... $1,000.
expired certificate.
3. Offering a limited 173.421(a)(4)....... $5,000 and up.
quantity of radioactive
materials without
marking the inner (or
single) packaging
``Radioactive''.
4. Offering low specific 173.427(a)(6)....... $800.
activity (LSA)
radioactive materials
consigned as exclusive
use without providing
instructions for
maintenance of
exclusive use shipment
controls.
5. Offering a package 173.441............. $10,000 and up.
that exceeds the
permitted limits for
surface radiation or
transport index.
6. Offering a package 173.443............. $5,000 and up.
without determining the
level of removable
external contamination,
or that exceeds the
limit for removable
external contamination.
7. Storing packages of 173.447(a).......... $5,000 and up.
radioactive material in
a group with a total
transport index more
than 50.
8. Offering special form 173.476(a), (b)..... $2,500.
radioactive materials
without maintaining a
complete safety
analysis or Certificate
of Competent Authority.
Offeror Requirements
(Cylinders):
Offering a compressed 173.301(c).......... $4,200 to $10,400.
gas for transportation
in a cylinder that is
out of test.
Failure to check each 173.303(d).......... $5,000.
day the pressure of a
cylinder charged with
acetylene that is
representative of that
day's compression,
after the cylinder has
cooled to a settled
temperature, or failure
to keep a record of
this test for at least
30 days.
Offering a limited 173.306(a)(3), (h).. $1,500 to $6,000.
quantity of a
compressed gas in a
metal container for the
purpose of propelling a
nonpoisonous material
and failing to heat the
cylinder until the
pressure is equivalent
to the equilibrium
pressure at 130 deg.F,
without evidence of
leakage, distortion, or
other defect.
------------------------------------------------------------------------
PART 178--REQUIREMENTS
------------------------------------------------------------------------
Third-Party Packaging
Certifiers (General):
1. Issuing a 171.2(e), 178.2(b), $500 per item.
certification that 178.3(a),
directs the packaging 178.503(a).
manufacturer to
improperly mark a
packaging (e.g., steel
drum to be marked UN
4G).
Manufacturers (General):
1. Failure to insure a 178.601(b)..........
packaging certified as
meeting the UN standard
is capable of passing
the required
performance testing.
a. Packing Group I .................... $10,800.
(includes Section
172.504 table 1
materials).
b. Packing Group II. .................... $8,400.
c. Packing Group III .................... $6,000.
2. Certifying a 178.601(d)..........
packaging as meeting a
UN standard when design
qualification testing
was not performed.
a. Packing Group I .................... $10,800.
(includes Section
172 504 table 1
materials).
b. Packing Group II. .................... $8,400.
c. Packing Group III .................... $6,000.
3. Failure to conduct 178.601(e).......... $2,000 to $10,800.
periodic retesting on
UN standard packaging
(depending on length of
time and Packing Group).
4. Failure to properly ....................
conduct testing for UN
standard packaging
(e.g., testing with
less weight than marked
on packaging; drop
testing from lesser
height than required;
failing to condition
fiberboard boxes before
design test).
a. Design 178.601(d).......... $2,000 to $10,800.
qualification
testing.
b. Periodic 178.601(e).......... $500 to $10,800.
retesting.
5. Marking, or causing 178.2(b), 178.3(a), $7,200.
the marking of, a 178.503(a)(8).
packaging with the
symbol of a
manufacturer or
packaging certifier
other than the company
that actually
manufactured or
certified the packaging.
6. Failure to maintain 178.601(1)..........
testing records.
a. Design .................... $1,000 to $5,000.
qualification
testing.
[[Page 42]]
b. Periodic .................... $500 to $2,000.
retesting.
7. Improper marking of 178.503............. $500 per item.
UN certification.
8. Manufacturing DOT 171.14..............
specification packaging
after October 1, 1994
that is not marked as
meeting a UN
performance standard.
a. If packaging does .................... $3,000.
meet DOT
specification.
b. If packaging does .................... $6,000 to $10,800.
not meet DOT
specification.
Manufacturing Requirements--
Drums:
1. Failure to properly
conduct production
leakproofness test.
a. Improper testing. 178.604(b)(1)....... $2,000.
b. No testing 173.28.............. $2,000 to $10,800.
performed.
Manufacturing Requirements--
Cylinders:
1. Manufacturing, Various............. $7,500 to $15,000.
representing, marking,
certifying, or selling
a DOT high-pressure
cylinder that was not
inspected and verified
by an approved
independent inspection
agency.
2. Failure to have a Various............. $800.
registration number or
failure to mark the
registration number on
the cylinder.
3. Marking another Various............. $7,200.
company's number on a
cylinder.
4. Failure to mark the 178.65.............. $3,000.
date of manufacture or
lot number on a DOT-39
cylinder.
5. Failure to have a Various............. $5,000.
chemical analysis
performed in the US for
a material manufactured
outside the US/failure
to obtain a chemical
analysis from the
foreign manufacturer.
6. Failure to meet wall Various............. $7,500 to $15,000.
thickness requirements.
7. Failure to heat treat Various............. $5,000 to $15,000.
cylinders prior to
testing.
8. Failure to conduct a Various............. $2,500 to $6,200.
complete visual
internal examination.
9. Failure to conduct a Various............. $2,500 to $6,200.
hydrostatic test, or
conducting a
hydrostatic test with
inaccurate test
equipment.
10. Failure to conduct a Various............. $7,500 to $15,000.
flattening test.
11. Failure to conduct a 178.65(f)(2)........ $5,000 to $15,000.
burst test on a DOT-39
cylinder.
12. Failure to have Various............. $7,500 to $15,000.
inspections and
verifications performed
by an inspector.
13. Failure to maintain Various.............
a required inspector's
reports.
a. No reports at all .................... $5,000.
b. Incomplete or .................... $1,000 to $4,000.
inaccurate reports.
------------------------------------------------------------------------
Other Requirements
------------------------------------------------------------------------
Carrier Requirements:
Transporting packages of 177.834(a) & (g).... $3,000.
hazardous materials
that have not been
secured against
movement within the
vehicle.
Transporting explosives 177.835(i).......... $5,200.
in a motor vehicle
containing metal or
other articles or
materials likely to
damage such explosives
or any package in which
they are contained,
without segregating in
different parts of the
load or securing them
in place in or on the
motor vehicle and
separated by bulkheads
or other suitable means
to prevent such damage.
Transporting railway 171.2(b)............ $7,000.
track torpedoes outside
of flagging kits, in
violation of E-7991.
Transporting Class 7 177.842(a)......... $5,000 and up.
(radioactive) material
having a total
transport index more
than 50.
Transporting Class 7 177.842(b)......... $5,000 and up.
(radioactive) material
without maintaining the
required separation
distance.
Failing to comply with 171.2(b)............
requirements of an
exemption authorizing
the transportation of
Class 7 (radioactive)
material having a total
transport index more
than 50.
--failure to have .................... $5,000.
the radiation
survey record
required by Paras.
7(f), 8(b)(3).
--failure to have .................... $500 each.
other accompanying
documents required
by para. 8(b).
--other violations .................... $5,000 and up.
of Paras. 7 and 8.
Exemptions:
Offering or transporting 171.2(a), (b), (c), $1,000 + $500 each
hazardous materials, or Various. add'l year.
otherwise performing a
function, covered by an
exemption after
expiration of the
exemption.
------------------------------------------------------------------------
III. Consideration of Statutory Criteria
A. These guidelines are used by the Office of Hazardous Materials
Safety (OHMS) in setting initial proposed penalties for hazmat
violations. They indicate baseline amounts or ranges for probable
violations frequently cited in enforcement reports and set forth general
OHMS policy for considering statutory criteria.
B. The initial baseline determination partially considers the
nature, extent, circumstances, and gravity of the alleged violation.
That determination then is adjusted to consider all other evidence
concerning the nature, extent, circumstances, and gravity of the alleged
violation; degree of culpability;
[[Page 43]]
history of prior violations; ability to pay; effect of the penalty on
ability to continue to do business; and such other matters as justice
may require (a major component of which is corrective action taken by a
respondent to prevent a recurrence of similar violations). In making a
penalty recommendation, the baseline or range may be increased or
decreased on the basis of evidence pertaining to these factors.
C. The following miscellaneous factors are used to implement one or
more of the statutory assessment criteria.
IV. Miscellaneous Factors Affecting Penalty Amounts
A. Corrective Action
1. A proposed penalty is mitigated for documented corrective action
of alleged violations taken by a respondent. Corrective action may
occur: (1) After an inspection and before a Notice of Probable Violation
(NOPV) is issued; (2) on receipt of an NOPV; or (3) after receipt of an
NOPV (possibly after it is solicited by an RSPA attorney). In general,
corrective action may reduce a penalty up to 25%. Mitigation may be
taken into account in the referral memo or may be recommended prior to
issuance of an Order by RSPA's Chief Counsel.
2. The two primary factors in determining the penalty reduction are
extent and timing of the corrective action. In other words, mitigation
will be determined on the basis of how much corrective action was taken
and when it was taken. Systemic action to prevent future violations is
given greater consideration than action simply to remedy violations
identified during the inspection.
3. Mitigation is applied to individual violations. Thus, in a case
with two violations, if corrective action for the first violation is
more extensive than for the second, the penalty for the first will be
mitigated more than that for the second.
B. Respondents That Re-Ship
A shipper that reships materials received from another company, in
the same packaging and without opening or altering the package,
independently is responsible for ensuring that the shipment complies
with Federal hazmat law, and independently may be subject to enforcement
action if the package does not comply. Nevertheless, the reshipper is
considered to have a lesser level of responsibility for compliance in
those respects in which it reasonably relies on the compliance of the
package as received. In most cases of this type, OHMS will discount the
applicable baseline standard by about 25%. The specific knowledge and
expertise of all parties must be considered in discounting for reliance
on a prior shipper. This discount is applied before any consideration of
mitigation based on corrective action.
C. Penalty Increases for Multiple Counts
Under the Federal hazmat law, 49 U.S.C. 5213(a), each violation of
the HMR and each day of a continuing violation (except for violations
pertaining to packaging manufacture or qualification) is subject to a
civil penalty of up to $25,000 ($27,500 for a violation occurring after
January 21, 1997). Absent aggravating factors, OHMS, in its exercise of
discretion, ordinarily will apply a single penalty for multiple counts
or days of violation. In a number of cases, particularly those involving
shippers, an inspector may cite two or more similar packaging violations
for different hazardous materials. For example, the inspector may cite
the same marking violation for two or more packages. OHMS usually will
consider those additional violations as counts of the same violation and
will not recommend multiples of the same baseline penalty. Rather, OHMS
usually will recommend the baseline penalty for a single violation,
increased by 25% for each additional violation.
D. Financial Considerations
1. Mitigation is appropriate when the baseline penalty would (1)
exceed an amount that the respondent is able to pay, or (2) have an
adverse effect on the respondent's ability to continue in business.
These criteria relate to a respondent's entire business, and not just
the product line or part of its operations involved in the violation(s).
Beyond the overall financial size of the respondent's business, the
relevant items of information on a respondent's balance sheet include
the current ratio (current assets to current liabilities), the nature of
current assets, and net worth (total assets minus total liabilities).
2. These figures are considered on a case-by-case basis. In general,
however, a current ratio close to or below 1.0 means that the company
may have difficulty in paying a large penalty, and may justify reduction
of the penalty or an installment payment plan. A small amount of cash on
hand representing limited liquidity, even with substantial other current
assets (such as accounts receivable or inventory), may warrant a short-
term payment plan. Respondent's income statement also will be reviewed
to determine whether a payment plan is appropriate.
3. Many companies are able to continue in business for extended
periods of time with a small or negative net worth, and many respondents
have paid substantial civil penalties in installments even though net
worth was negative. For this reason, negative net worth alone does not
always warrant reduction of a proposed penalty or even, in the absence
of factors discussed above, a payment plan.
4. In general, an installment payment plan may be justified where
reduction of a proposed penalty is not, but the appropriateness
[[Page 44]]
of either (or both) will depend on the circumstances of the case. The
length of a payment plan should be as short as possible, but the plan
may consider seasonal fluctuations in a company's income if the
company's business is seasonal (e.g., swimming pool chemical sales,
fireworks sales) or if the company has documented specific reasons for
current non-liquidity.
5. Evidence of financial condition is used only to decrease a
penalty, and not to increase it.
E. Penalty Increases for Prior Violations
1. The baseline penalty presumes an absence of prior violations. If
prior violations exist, generally they will serve to increase a proposed
penalty. The general standard for increasing a baseline proposed penalty
on the basis of prior violations is as follows:
a. One prior case--25% increase over the pre-mitigation recommended
penalty
b. Two prior cases--50% increase over the pre-mitigation recommended
penalty
c. Three prior cases--75% increase over the pre-mitigation recommended
penalty
d. Four or more prior cases--100% increase over the pre-mitigation
recommended penalty
2. A case of prior violations closed more than five years previously
normally will not be considered in determining a proposed penalty.
F. Penalty Increases for Use of Expired Exemptions
Adjustments to the base line figures for use of expired exemptions
can be made depending on how much material has been shipped during the
period between the expiration date and the renewal date. If the company
previously has been found to have operated under an expired exemption,
the penalty is normally doubled. If the company has been previously
cited for other violations, the penalty generally will be increased by
about 25%.
[Amdt. 107-33, 60 FR 12141, Mar. 6, 1995, as amended by Amdt. 107-40, 62
FR 2972, 2977, Jan. 21, 1997; 62 FR 51556, Oct. 1, 1997; 65 FR 58618,
Sept. 29, 2000; 66 FR 45180, Aug. 28, 2001]
Subpart E--Designation of Approval and Certification Agencies
Sec. 107.401 Purpose and scope.
(a) This subpart establishes procedures for the designation of
agencies to issue approval certificates and certifications for types of
packagings designed, manufactured, tested, or maintained in conformance
with the requirements of this subchapter, subchapter C of this chapter,
and standards set forth in the United Nations (U.N.) Recommendations
(Transport of Dangerous Goods). Except for certifications of compliance
with U.N. packaging standards, this subpart does not apply unless made
applicable by a rule in subchapter C of this chapter.
(b) The Associate Administrator may issue approval certificates and
certifications addressed in paragraph (a) of this section.
[Amdt. 107-31, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23,
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]
Sec. 107.402 Application for designation as an approval or certification agency.
(a) Any organization or person seeking designation as an approval or
certification agency shall apply in writing to the Associate
Administrator for Hazardous Materials Safety (DHM-32), Department of
Transportation, 400 Seventh Street, SW., Washington DC 20590-0001. Each
application must be signed and certified to be correct by the applicant
or, if the applicant is an organization, by an authorized officer or
official representative of the organization. Any false statement or
representation, or the knowing and willful concealment of a material
fact, may subject the applicant to prosecution under the provisions of
18 U.S.C. 1001, result in the denial or termination of a designation.
(b) Each application for designation must be in English and include
the following information:
(1) Name and address of the applicant, including place of
incorporation if a corporation. In addition, if the applicant is not a
resident of the United States, the name and address of a permanent
resident of the United States designated in accordance with Sec. 107.7
to serve as agent for service of process.
(2) If the applicant's principal place of business is in a country
other than the United States, a copy of the designation from the
Competent Authority of that country delegating to the applicant an
approval or designated agency authority for the type of packaging for
which a DOT designation is
[[Page 45]]
sought, and a statement that the Competent Authority also delegates
similar authority to U.S. Citizens or organizations having designations
under this subpart from the RSPA.
(3) A listing, by DOT specification (or exemption) number, or U.N.
designation, of the types of packagings for which approval authority is
sought.
(4) A personnel qualifications plan listing the qualifications that
the applicant will require of each person to be used in the performance
of each packaging approval or certification function. As a minimum,
these qualifications must include:
(i) The ability to review and evaluate design drawings, design and
stress calculations;
(ii) A knowledge of the applicable regulations of subchapter C of
this chapter and, when applicable, U.N. standards; and
(iii) The ability to conduct or monitor and evaluate test procedures
and results; and
(iv) The ability to review and evaluate the qualifications of
materials and fabrication procedures.
(5) A statement that the applicant will perform its functions
independent of the manufacturers and owners of the packagings concerned.
(6) A statement that the applicant will allow the Associate
Administrator or his representative to inspect its records and
facilities in so far as they relate to the approval or certification of
specification packagings and shall cooperate in the conduct of such
inspections.
(c) The applicant shall furnish any additional information relevant
to the applicant's qualifications, if requested by the Associate
Administrator.
[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985; 50 FR 16089, Apr. 24, 1985,
as amended by Amdt. 107-22, 55 FR 39978, Oct. 1, 1990; Amdt. 107-23, 56
FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]
Sec. 107.403 Designation of approval agencies.
(a) If the Associate Administrator determines that an application
contains all the required information, the applicant is sent a letter of
designation and assigned an identification code.
(b) If the Associate Administrator determines that an application
does not contain all the required information, the application is denied
and the applicant is sent a written notice containing all the reasons
for the denial.
(c) Within 30 days of an initial denial of an application under
paragraph (b) of this section, the applicant may file an amended
application. If after considering the amended application, the Associate
Administrator determines that it should be denied, he notifies the
applicant, and the denial constitutes the final action of the Associate
Administrator on the application. Within 60 days of receipt of the final
denial the applicant may appeal the denial to the Administrator, RSPA,
setting forth in writing where the Associate Administrator for Hazardous
Materials Safety erred in this determination.
[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23,
56 FR 66157, Dec. 20, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994;
66 FR 45377, Aug. 28, 2001]
Sec. 107.404 Conditions of designation.
(a) Each designation made under this subpart contains the following
conditions:
(1) The designated approval or certification agency may use only
testing equipment that it has determined, through personal inspection,
to be suitable for the purpose.
(2) Each approval certificate and certification issued by the
designated approval agency must contain the name and identification code
of the approval agency.
(3) Each approval certificate and certification must be in a format
acceptable to the Associate Administrator.
(b) The designated approval agency shall notify the Associate
Administrator within 20 days after the date there is any change in the
information submitted under Sec. 107.402.
(c) The designated approval agency shall comply with all of the
terms and conditions stated in its letter of designation under the
subpart.
(d) Nothing in this part relieves a manufacturer or owner of a
packaging of responsibility for compliance with
[[Page 46]]
any of the applicable requirements of this title.
[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23,
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]
Sec. 107.405 Termination of designation.
(a) Any designation issued under Sec. 107.403 of this subchapter may
be suspended or terminated if the Associate Administrator determines
that:
(1) The application for designation contained a misrepresentation,
or the applicant willfully concealed a material fact.
(2) The approval agency failed to comply with a term or condition
stated in the agency's letter of designation.
(3) The Competent Authority of an approval agency of a country
outside the United States has failed to initiate, maintain or recognize
a qualified U.S. approval agency.
(b) Before a designation is suspended or terminated, the Associate
Administrator shall give to the approval agency:
(1) Written notice of the facts or conduct believed to warrant
suspension or termination of the designation.
(2) Sixty days in which to show in writing why the designation
should not be suspended or terminated.
[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23,
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]
Subpart F--Registration of Cargo Tank and Cargo Tank Motor Vehicle
Manufacturers and Repairers and Cargo Tank Motor Vehicle Assemblers
Sec. 107.501 Scope.
(a) This subpart establishes a registration procedure for persons
who are engaged in the manufacture, assembly, inspection and testing,
certification, or repair of a cargo tank or a cargo tank motor vehicle
manufactured in accordance with a DOT specification under subchapter C
of this chapter or under terms of an exemption issued under this part.
(b) Persons engaged in continuing qualification and maintenance of
cargo tanks and cargo tank motor vehicles must be familiar with the
requirements set forth in part 180, subpart E, of this chapter.
[Amdt. 107-20, 55 FR 37047, Sept. 7, 1990]
Sec. 107.502 General registration requirements.
(a) Definitions: For purposes of this subpart--
(1) Assembly means the assembly of one or more tanks or cargo tanks
to a motor vehicle or to a motor vehicle suspension component and
involves no welding on the cargo tank wall.
(2) The terms Authorized Inspector, Cargo tank, Cargo tank motor
vehicle, Design Certifying Engineer, Registered Inspector, and Person
are defined in Sec. 171.8 of this chapter.
(3) The terms cargo tank wall and manufacturer are defined in
Sec. 178.320(a), and repair is defined in Sec. 180.403 of this chapter.
(b) No person may engage in the manufacture, assembly,
certification, inspection or repair of a cargo tank or cargo tank motor
vehicle manufactured under the terms of a DOT specification under
subchapter C of this chapter or an exemption issued under this part
unless the person is registered with the Department in accordance with
the provisions of this subpart. A person employed as an inspector or
design certifying engineer is considered to be registered if the
person's employer is registered.
(c) A person who performs functions which are subject to the
provisions of this subpart may perform only those functions which have
been identified to the Department in accordance with the procedures of
this subpart.
(d) Registration statements must be in English, contain all of the
information required by this subpart, and be submitted to: Approvals
Branch, Associate Administrator for Hazardous Materials Safety, Attn:
DHM-32, Research and Special Programs Administration, Department of
Transportation, Washington, DC 20590-0001.
(e) Upon determination that a registration statement contains all
the information required by this subpart, the Department will send the
registrant a letter confirming receipt of the registration application
and assigning a registration number to that person. A separate
registration number will be
[[Page 47]]
assigned for each cargo tank manufacturing, assembly, repair facility or
other place of business identified by the registrant.
[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37047, Sept. 7, 1990,
as amended by Amdt. 107-22, 55 FR 39978, Oct. 1, 1990; Amdt. 107-23, 56
FR 66157, Dec. 20, 1991; Amdt. 107-28, 58 FR 46873, Sept. 3, 1993; Amdt.
107-39, 61 FR 51337, Oct. 1, 1996]
Sec. 107.503 Registration statement.
(a) Each registration statement must be in English and contain the
following information:
(1) Name;
(2) Street address, mailing address and telephone number for each
facility or place of business;
(3) A statement signed by the person responsible for compliance with
the applicable requirements of this chapter, certifying knowledge of
those requirements and that each employee who is a Registered Inspector
or Design Certifying Engineer meets the minimum qualification
requirements set forth in Sec. 171.8 of this chapter for ``Registered
Inspector'' or ``Design Certifying Engineer''. The following language
may be used.
I certify that all Registered Inspectors and Design Certifying
Engineers used in performance of the prescribed functions meet the
minimum qualification requirements set forth in 49 CFR 171.8, that I am
the person responsible for ensuring compliance with the applicable
requirements of this chapter, and that I have knowledge of the
requirements applicable to the functions to be performed.
(4) A description of the specific functions to be performed on cargo
tanks or cargo tank motor vehicles, e.g.:
(i) Manufacture,
(ii) Assembly,
(iii) Inspection and testing (specify type, e.g., external or
internal visual inspection, lining inspection, hydrostatic pressure
test, leakage test, thickness test),
(iv) Certification,
(v) Repair, or
(vi) Equipment manufacture;
(5) An identification of the types of DOT specification and
exemption cargo tanks or cargo tank motor vehicles which the registrant
intends to manufacture, assemble, repair, inspect, test or certify;
(6) A statement indicating whether the registrant employs Registered
Inspectors or Design Certifying Engineers to conduct certification,
inspection or testing functions addressed by this subpart. If the
registrant engages a person who is not an employee of the registrant to
perform these functions, provide the name, address and registration
number of that person; and
(7) If the registrant is not a resident of the United States, the
name and address of a permanent resident of the United States designated
in accordance with Sec. 107.7 to serve as agent for service of process.
(b) In addition to the information required under paragraph (a) of
this section, each person who manufactures a cargo tank or cargo tank
motor vehicle must submit a copy of the manufacturer's current ASME
Certificate of Authorization for the use of the ASME ``U'' stamp.
(c) In addition to the information required under paragraph (a) of
this section, each person who repairs a cargo tank or cargo tank motor
vehicle must submit a copy of the repair facility's current National
Board Certificate of Authorization for the use of the ``R'' stamp or
ASME Certificate of Authorization for the use of the ASME ``U'' stamp.
Any person who repairs MC-series cargo tanks which are not certified to
the ASME Code must submit a copy of the National Board or ASME
Certificate of Authorization to RSPA before June 30, 1992.
[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37047, Sept. 7, 1990;
57 FR 365, Jan. 6, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994;
Amdt. 107-39, 61 FR 51337, Oct. 1, 1996; 63 FR 52846, Oct. 1, 1998]
Sec. 107.504 Period of registration, updates, and record retention.
(a) Registration will be for a maximum of six years from the date of
the original registration.
(b) Any correspondence with the Department must contain the
registrant's name and registration number.
(c) A registration must be renewed every six years or within thirty
days of reissuance of an ASME or National Board Certification, whichever
occurs
[[Page 48]]
first, by submitting an up-to-date registration statement containing the
information prescribed by Sec. 107.503. Any person initially registered
under the provisions of Sec. 107.502 and who is in good standing is
eligible for renewal.
(d) A registrant shall provide written notification to the
Department within thirty days of any of the following occurrences:
(1) Any change in the registration information submitted under
Sec. 107.503;
(2) Replacement of the person responsible for compliance with the
requirements in Sec. 107.503(a)(3). If this occurs, the registrant shall
resubmit the required certification;
(3) Loss of ASME or National Board Certificate of Authorization; or
(4) A change in function; such as, from assembly to manufacture, an
addition of a function, or a change to the types of inspections, tests
or certifications of cargo tanks or cargo tank motor vehicles.
(e) Each registrant shall maintain a current copy of the
registration information submitted to the Department and a current copy
of the registration number identification received from the Department
at the location identified in Sec. 107.503(a)(2) during such time the
person is registered with the Department and for two years thereafter.
(f) The issuance of a registration number under this subpart is not
an approval or endorsement by the Department of the qualifications of
any person to perform the specified functions.
[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37048, Sept. 7, 1990,
as amended by Amdt. 107-20, 56 FR 27875, June 17, 1991; Amdt. 107-37, 61
FR 18931, Apr. 29, 1996]
Subpart G--Registration of Persons Who Offer or Transport Hazardous
Materials
Source: Amdt. No. 107-26, 57 FR 30630, July 9, 1992, unless
otherwise noted.
Sec. 107.601 Applicability.
(a) The registration and fee requirements of this subpart apply to
any person who offers for transportation, or transports, in foreign,
interstate or intrastate commerce--
(1) A highway route-controlled quantity of a Class 7 (radioactive)
material, as defined in Sec. 173.403 of this chapter;
(2) More than 25 kg (55 pounds) of a Division 1.1,1.2.or 1.3
(explosive) material (see Sec. 173.50 of this chapter) in a motor
vehicle, rail car or freight container;
(3) More than one L (1.06 quarts) per package of a material
extremely toxic by inhalation (i.e., ``material poisonous by
inhalation,'' as defined in Sec. 171.8 of this chapter, that meets the
criteria for ``hazard zone A,'' as specified in Secs. 173.116(a) or
173.133(a) of this chapter);
(4) A shipment of a quantity of hazardous materials in a bulk
packaging (see Sec. 171.8 of this chapter) having a capacity equal to or
greater than 13,248 L (3,500 gallons) for liquids or gases or more than
13.24 cubic meters (468 cubic feet) for solids;
(5) A shipment in other than a bulk packaging of 2,268 kg (5,000
pounds) gross weight or more of one class of hazardous materials for
which placarding of a vehicle, rail car, or freight container is
required for that class, under the provisions of subpart F of part 172
of this chapter; or
(6) Except as provided in paragraph (b) of this section, a quantity
of hazardous material that requires placarding, under provisions of
subpart F of part 172 of this chapter.
(b) Paragraph (a)(6) of this section does not apply to those
activities of a farmer, as defined in Sec. 171.8 of this chapter, that
are in direct support of the farmer's farming operations.
(c) In this subpart, the term ``shipment'' means the offering or
loading of hazardous material at one loading facility using one
transport vehicle, or the transport of that transport vehicle.
[65 FR 7309, Feb. 14, 2000]
Sec. 107.606 Exceptions.
(a) The following are excepted from the requirements of this
subpart:
(1) An agency of the Federal government.
(2) A State agency.
(3) An agency of a political subdivision of a State.
(4) An employee of any of those agencies in paragraphs (a)(1)
through (a)(3)
[[Page 49]]
of this section with respect to the employee's official duties.
(5) A hazmat employee (including, for purposes of this subpart, the
owner-operator of a motor vehicle that transports in commerce hazardous
materials, if that vehicle at the time of those activities, is leased to
a registered motor carrier under a 30-day or longer lease as prescribed
in 49 CFR part 376 or an equivalent contractual agreement).
(6) A person domiciled outside the United States, who offers solely
from a location outside the United States, hazardous materials for
transportation in commerce, provided that the country of which such a
person is a domiciliary does not require persons domiciled in the United
States, who solely offer hazardous materials for transportation to the
foreign country from places in the United States, to file a registration
statement or to pay a registration fee.
(b) Upon making a determination that persons domiciled in the United
States, who offer hazardous materials for transportation to a foreign
country solely from places in the United States, must file registration
statements or pay fees to that foreign country, the U.S. Competent
Authority will provide notice of such determination directly to the
Competent Authority of that foreign country and by publication in the
Federal Register. Persons who offer hazardous materials for
transportation to the United States from that foreign country must file
a registration statement and pay the required fee no later than 60 days
following publication of the determination in the Federal Register.
[Amdt 107-34, 60 FR 27233, May 23, 1995, as amended at 63 FR 52847, Oct.
1, 1998]
Sec. 107.608 General registration requirements.
(a) Except as provided in Sec. 107.616(d), each person subject to
this subpart must submit a complete and accurate registration statement
on DOT Form F 5800.2 not later than June 30 for each registration year,
or in time to comply with paragraph (b) of this section, whichever is
later. Each registration year begins on July 1 and ends on June 30 of
the following year.
(b) No person required to file a registration statement may
transport a hazardous material or cause a hazardous material to be
transported or shipped, unless such person has on file, in accordance
with Sec. 107.620, a current Certificate of Registration in accordance
with the requirements of this subpart.
(c) A registrant whose name or principal place of business has
changed during the year of registration must notify RSPA of that change
by submitting an amended registration statement not later than 30 days
after the change.
(d) Copies of DOT Form F 5800.2 and instructions for its completion
may be obtained from the Hazardous Materials Registration Program, DHM-
60, U.S. Department of Transportation, Washington, DC 20590-0001, by
calling 617-494-2545 or 202-366-4109, or via the Internet at ``http://
hazmat.dot.gov''.
(e) If the registrant is not a resident of the United States, the
registrant must attach to the registration statement the name and
address of a permanent resident of the United States, designated in
accordance with Sec. 107.7, to serve as agent for service of process.
[Amdt. No. 107-26, 57 FR 30630, July 9, 1992, as amended by Amdt. 107-
31, 59 FR 32932, June 27, 1994; 65 FR 7309, Feb. 14, 2000]
Sec. 107.612 Amount of fee.
(a) Registration year 1999-2000 and earlier. For all registration
years through 1999-2000, each person subject to the requirements of
Sec. 107.601(a)(1)-(5) of this subpart must pay an annual fee of $300
(which includes a $50 processing fee).
(b) Registration year 2000-2001 and following. For each registration
year beginning with 2000-2001, each person subject to the requirements
of this subpart must pay an annual fee as follows:
(1) Small business. Each person that qualifies as a small business
under criteria specified in 13 CFR part 121 applicable to the standard
industrial classification (SIC) code that describes that person's
primary commercial activity must pay an annual fee of $275 and the
processing fee required by paragraph (b)(3) of this section.
(2) Other than a small business. Each person that does not meet
criteria
[[Page 50]]
specified in paragraph (b)(1) of this section must pay an annual fee of
$1,975 and the processing fee required by paragraph (b)(3) of this
section.
(3) Processing fee. The processing fee is $25 for each registration
statement filed. A single statement may be filed for one, two, or three
registration years as provided in Sec. 107.616(c).
[65 FR 7309, Feb. 14, 2000]
Sec. 107.616 Payment procedures.
(a) Except as provided in paragraph (d) of this section, each person
subject to the requirements of this subpart must mail the registration
statement and payment in full to the U.S. Department of Transportation,
Hazardous Materials Registration, P.O. Box 740188, Atlanta, Georgia
30374-0188. A registrant required to file an amended registration
statement under Sec. 107.608(c) must mail it to the same address.
(b) Payment must be made by certified check, cashier's check,
personal check, or money order in U.S. funds and drawn on a U.S. bank,
payable to the U.S. Department of Transportation and identified as
payment for the ``Hazmat Registration Fee'' or by a VISA or MasterCard
credit card authorization completed and signed on the registration
statement.
(c) Payment must correspond to the total fees properly calculated in
the ``Amount Due'' block of the DOT form F 5800.2. A person may elect to
register and pay the required fees for up to three registration years by
filing one complete and accurate registration statement.
(d) A person may obtain a temporary registration number, valid for
45 days from the date of issuance, through an expedited registration
process as follows:
(1) Contact RSPA by telephone (800-942-6990 or 617-494-2545) and
provide name, principal place of business, and credit card payment
information;
(2) Pay a registration and processing fee of $350 (including a $50
expedited handling fee). For registration years 2000-2001 and following,
persons who do not meet the criteria for a small business, as specified
in Sec. 107.612(b)(1), must enclose an additional payment of $1,700 with
the expedited follow-up material, for a total of $2,050 (including a $50
expedited handling fee); and
(3) Submit a completed registration statement and proof of payment
to RSPA before the expiration date of the temporary registration number.
[Amdt. 107-26, 57 FR 30630, July 9, 1992, as amended by Amdt. 107-26, 58
FR 12545, Mar. 5, 1993; 65 FR 7310, Feb. 14, 2000]
Sec. 107.620 Recordkeeping requirements.
(a) Each person subject to the requirements of this subpart, or its
agent designated under Sec. 107.608(e), must maintain at its principal
place of business for a period of three years from the date of issuance
of each Certificate of Registration:
(1) A copy of the registration statement filed with RSPA; and
(2) The Certificate of Registration issued to the registrant by
RSPA.
(b) After January 1, 1993, each motor carrier subject to the
requirements of this subpart must carry a copy of its current
Certificate of Registration issued by RSPA or another document bearing
the registration number identified as the ``U.S. DOT Hazmat Reg. No.''
on board each truck and truck tractor (not including trailers and semi-
trailers) used to transport hazardous materials subject to the
requirements of this subpart. The Certificate of Registration or
document bearing the registration number must be made available, upon
request, to enforcement personnel.
(c) In addition to the requirements of paragraph (a) of this
section, after January 1, 1995, each person who transports by vessel a
hazardous material subject to the requirements of this subpart must
carry on board the vessel a copy of its current Certificate of
Registration or another document bearing the current registration number
identified as the ``U.S. DOT Hazmat Reg. No.''
(d) Each person subject to this subpart must furnish its Certificate
of Registration (or a copy thereof) and all other records and
information pertaining to the information contained in
[[Page 51]]
the registration statement to an authorized representative or special
agent of DOT upon request.
[Amdt. No. 107-26, 57 FR 30630, July 9, 1992, as amended at 57 FR 37902,
August 21, 1992; Amdt. 107-26, 58 FR 12545, Mar. 5, 1993; Amdt. 107-31,
59 FR 32932, June 27, 1994]
Subpart H--Approvals, Registrations and Submissions
Source: Amdt. 107-38, 61 FR 21100, May 9, 1996, unless otherwise
noted.
Sec. 107.701 Purpose and scope.
(a) This subpart prescribes procedures for the issuance,
modification and termination of approvals, and the submission of
registrations and reports, as required by this chapter.
(b) The procedures of this subpart are in addition to any
requirements in subchapter C of this chapter applicable to a specific
approval, registration or report. If compliance with both a specific
requirement of subchapter C of this chapter and a procedure of this
subpart is not possible, the specific requirement applies.
(c) Registration under subpart F or G of this part is not subject to
the procedures of this subpart.
[Amdt. 107-38, 61 FR 21100, May 9, 1996; Amdt. 107-38, 61 FR 27948, June
3, 1996]
Sec. 107.705 Registrations, reports, and applications for approval.
(a) A person filing a registration, report, or application for an
approval, or a renewal or modification of an approval subject to the
provisions of this subpart must--
(1) File the registration, report, or application with the Associate
Administrator for Hazardous Materials Safety, Research and Special
Programs Administration, U.S. Department of Transportation, 400 7th
Street, SW, Washington, DC 20590-0001, Attention: Approvals, DHM-32;
(2) Identify the section of the chapter under which the
registration, report, or application is made;
(3) If a report is required by an approval, a registration or an
exemption, identify the approval, registration or exemption number;
(4) Provide the name, street and mailing addresses, e-mail address
optional, and telephone number of the person on whose behalf the
registration, report, or application is made and, if different, the
person making the filing;
(5) If the person on whose behalf the filing is made is not a
resident of the United States, provide a designation of agent for
service in accordance with Sec. 107.7;
(6) Provide a description of the activity for which the registration
or report is required; and
(7) Provide additional information as requested by the Associate
Administrator, if the Associate Administrator determines that a filing
lacks pertinent information or otherwise does not comply with applicable
requirements.
(b) In addition to the provisions in paragraph (a) for an approval,
an application for an approval, or an application for modification or
renewal of an approval, the applicant must provide--
(1) A description of the activity for which the approval is
required;
(2) The proposed duration of the approval;
(3) The transport mode or modes affected, as applicable;
(4) Any additional information specified in the section containing
the approval; and
(5) For an approval which provides exceptions from regulatory
requirements or prohibitions--
(i) Identification of any increased risk to safety or property that
may result if the approval is granted, and specification of the measures
that the applicant considers necessary or appropriate to address that
risk; and
(ii) Substantiation, with applicable analyses or evaluations, if
appropriate, demonstrating that the proposed activity will achieve a
level of safety that is at least equal to that required by the
regulation.
(c) For an approval with an expiration date, each application for
renewal or modification must be filed in the same manner as an original
application. If a complete and conforming renewal application is filed
at least 60 days before the expiration date of an approval, the
Associate Administrator, on written request from the applicant,
[[Page 52]]
will issue a written extension to permit operation under the terms of
the expired approval until a final decision on the application for
renewal has been made. Operation under an expired approval is prohibited
absent a written extension. This paragraph does not limit the authority
of the Associate Administrator to modify, suspend or terminate an
approval under Sec. 107.713.
(d) To request confidential treatment for information contained in
the application, the applicant shall comply with Sec. 107.5(a).
[Amdt. 107-38, 61 FR 21100, May 9, 1996, as amended at 65 FR 50457, Aug.
18, 2000]
Sec. 107.709 Processing of an application for approval, including an application for renewal or modification.
(a) No public hearing or other formal proceeding is required under
this subpart before the disposition of an application.
(b) At any time during the processing of an application, the
Associate Administrator may request additional information from the
applicant. If the applicant does not respond to a written request for
additional information within 30 days of the date the request was
received, the application may be deemed incomplete and denied. However,
if the applicant responds in writing within the 30-day period requesting
an additional 30 days within which it will gather the requested
information, the Associate Administrator may grant the 30-day extension.
(c) The Associate Administrator may grant or deny an application, in
whole or in part. At the Associate Administrator's discretion, an
application may be granted subject to provisions that are appropriate to
protect health, safety and property. The Associate Administrator may
impose additional provisions not specified in the application, or delete
conditions in the application which are unnecessary.
(d) The Associate Administrator may grant an application on finding
that--
(1) The application complies with this subpart;
(2) The application demonstrates that the proposed activity will
achieve a level of safety that--
(i) Is at least equal to that required by the regulation, or
(ii) If the regulations do not establish a level of safety, is
consistent with the public interest and adequately will protect against
the risks to life and property inherent in the transportation of
hazardous materials in commerce;
(3) The application states all material facts, and contains no
materially false or materially misleading statement;
(4) The applicant meets the qualifications required by applicable
regulations; and
(5) The applicant is fit to conduct the activity authorized by the
approval, or renewal or modification of approval. This assessment may be
based on information in the application, prior compliance history of the
applicant, and other information available to the Associate
Administrator.
(e) Unless otherwise specified in this chapter or by the Associate
Administrator, an approval in which a term is not specified does not
expire.
(f) The Associate Administrator notifies the applicant in writing of
the decision on the application. A denial contains a brief statement of
reasons.
Sec. 107.711 Withdrawal.
An application may be withdrawn at any time before a decision to
grant or deny it is made. Withdrawal of an application does not
authorize the removal of any related records from the RSPA dockets or
files. Applications that are eligible for confidential treatment under
Sec. 107.5 will remain confidential after the application is withdrawn.
The duration of this confidential treatment for trade secrets and
commercial or financial information is indefinite, unless the party
requesting the confidential treatment of the materials notifies the
Associate Administrator that the confidential treatment is no longer
required.
Sec. 107.713 Approval modification, suspension or termination.
(a) The Associate Administrator may modify an approval on finding
that--
(1) Modification is necessary to conform an existing approval to
relevant statutes and regulations as they may be amended from time to
time; or
(2) Modification is required by changed circumstances to enable the
[[Page 53]]
approval to continue to meet the standards of Sec. 107.709(d).
(b) The Associate Administrator may modify, suspend or terminate an
approval, as appropriate, on finding that--
(1) Because of a change in circumstances, the approval no longer is
needed or no longer would be granted if applied for;
(2) The application contained inaccurate or incomplete information,
and the approval would not have been granted had the application been
accurate and complete;
(3) The application contained deliberately inaccurate or incomplete
information; or
(4) The holder knowingly has violated the terms of the approval or
an applicable requirement of this chapter in a manner demonstrating lack
of fitness to conduct the activity for which the approval is required.
(c) Except as provided in paragraph (d) of this section, before an
approval is modified, suspended or terminated, the Associate
Administrator notifies the holder in writing of the proposed action and
the reasons for it, and provides an opportunity to show cause why the
proposed action should not be taken.
(1) The holder may file a written response with the Associate
Administrator within 30 days of receipt of notice of the proposed
action.
(2) After considering the holder's or party's written response, or
after 30 days have passed without response since receipt of the notice,
the Associate Administrator notifies the holder in writing of the final
decision with a brief statement of reasons.
(d) The Associate Administrator, if necessary to avoid a risk of
significant harm to persons or property, may in the notification declare
the proposed action immediately effective.
Sec. 107.715 Reconsideration.
(a) An applicant or a holder may request that the Associate
Administrator reconsider a decision under Sec. 107.709(f) or
Sec. 107.713(c). The request must:
(1) Be in writing and filed within 20 days of receipt of the
decision;
(2) State in detail any alleged errors of fact and law;
(3) Enclose any additional information needed to support the request
to reconsider; and
(4) State in detail the modification of the final decision sought.
(b) The Associate Administrator considers newly submitted
information on a showing that the information could not reasonably have
been submitted during application processing.
(c) The Associate Administrator grants or denies, in whole or in
part, the relief requested and informs the requesting person in writing
of the decision.
Sec. 107.717 Appeal.
(a) A person who requested reconsideration under Sec. 107.715 may
appeal to the Administrator the Associate Administrator's decision on
the request. The appeal must:
(1) Be in writing and filed within 30 days of receipt of the
Associate Administrator's decision on reconsideration;
(2) State in detail any alleged errors of fact and law;
(3) Enclose any additional information needed to support the appeal;
and
(4) State in detail the modification of the final decision sought.
(b) The Administrator, if necessary to avoid a risk of significant
harm to persons or property, may declare the Associate Administrator's
action effective pending a decision on appeal.
(c) The Administrator grants or denies, in whole or in part, the
relief requested and informs the appellant in writing of the decision on
appeal. The Administrator's decision on appeal is the final
administrative action.
PART 110--HAZARDOUS MATERIALS PUBLIC SECTOR TRAINING AND PLANNING GRANTS--Table of Contents
Sec.
110.1 Purpose.
110.5 Scope.
110.7 Control Number under the Paperwork Reduction Act.
110.10 Eligibility.
110.20 Definitions.
110.30 Grant application.
110.40 Activities eligible for funding.
110.50 Disbursement of Federal funds.
110.60 Cost sharing for planning and training.
110.70 Financial administration.
[[Page 54]]
110.80 Procurement.
110.90 Grant monitoring, reports, and records retention.
110.100 Enforcement.
110.110 After-grant requirements.
110.120 Deviation from this part.
110.130 Disputes.
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
Source: Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, unless otherwise
noted.
Sec. 110.1 Purpose.
This part sets forth procedures for reimbursable grants for public
sector planning and training in support of the emergency planning and
training efforts of States, Indian tribes, and local communities to deal
with hazardous materials emergencies, particularly those involving
transportation. These grants will enhance the implementation of the
Emergency Planning and Community Right-to-Know Act of 1986 (42 U.S.C.
11001).
Sec. 110.5 Scope.
(a) This part applies to States and Indian tribes and contains the
program requirements for public sector training and planning grants to
support hazardous materials emergency planning and training efforts.
(b) The requirements contained in 49 CFR part 18, ``Uniform
Administrative Requirements for Grants and Cooperative Agreements to
State and Local Governments'', apply to grants issued under this part.
(c) Copies of standard forms and OMB circulars referenced in this
part are available from the HMTUSA Grants Manager, Research and Special
Programs Administration, U.S. Department of Transportation, 400 Seventh
Street, SW., Washington DC 20590-0001.
Sec. 110.7 Control Number under the Paperwork Reduction Act.
The Office of Management and Budget control number assigned to
collection of information in Secs. 110.30, 110.70, 110.80, and 110.90 is
2137-0586.
Sec. 110.10 Eligibility.
This part applies to States and Indian tribes. States may apply for
planning and training grants. Federally-recognized Indian tribes may
apply for training grants.
Sec. 110.20 Definitions.
Unless defined in this part, all terms defined in 49 U.S.C. 5102 are
used in their statutory meaning and all terms defined in 49 CFR part 18
and OMB Circular A-102, with respect to administrative requirements for
grants, are used as defined therein. Other terms used in this part are
defined as follows:
Allowable costs means those costs that are: eligible, reasonable,
necessary, and allocable to the project permitted by the appropriate
Federal cost principles, and approved in the grant.
Associate Administrator means the Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration.
Budget period means the period of time specified in the grant
agreement during which the project manager may expend or obligate
project funds.
Cost review means the review and evaluation of costs to determine
reasonableness, allocability, and allowability.
Indian country means Indian country as defined in 18 U.S.C. 1151.
That section defines Indian country as all land within the limits of any
reservation under the jurisdiction of the U.S. Government,
notwithstanding the issuance of any patent, and, including rights-of-way
running through the reservation; all dependent Indian communities within
the borders of the United States whether within the original or
subsequently acquired territory thereof, and whether within or without
the limits of a State; and all Indian allotments, the Indian titles to
which have not been extinguished, including rights-of-way running
through the same.
Indian tribe means a tribe ``Federally-recognized'' by the Secretary
of the Interior under 25 CFR 272.2.
Local Emergency Planning Committee (LEPC) means a committee
appointed by the State Emergency Response Commission under section
301(c) of the Emergency Planning and Community Right-to-Know Act of 1986
(42 U.S.C. 11001(c)) that includes at a minimum, representatives from
each of the following groups or organizations: elected State and local
officials; law enforcement, firefighting, civil defense, first aid,
health, local environmental, hospital, and transportation personnel;
[[Page 55]]
broadcast and print media; community groups; and owners and operators of
facilities subject to the emergency planning requirements.
National curriculum means the curriculum required to be developed
under 49 U.S.C. 5115 and necessary to train public sector emergency
response and preparedness teams, enabling them to comply with
performance standards as stated in 49 U.S.C. 5115(c).
Political subdivision means a county, municipality, city, town,
township, local public authority (including any public and Indian
housing agency under the United States Housing Act of 1937 (42 U.S.C.
1401 et seq.), school district, special district, intrastate district,
council of governments (whether or not incorporated as a nonprofit
corporation under State law), any other regional or interstate
government entity, or any agency or instrumentality of a local
government.
Project means the activities and tasks identified in the grant
agreement.
Project manager means the State or Indian tribal official designated
in a grant as the recipient agency's principal program contact with the
Federal Government.
Project officer means the Federal official designated in a grant as
the program contact with the project manager. The project officer is
responsible for monitoring the project.
Project period means the length of time specified in a grant for
completion of all work associated with that project.
State Emergency Response Commission (SERC) means the State Emergency
Response Commission appointed by the Governor of each State and
Territory under the Emergency Planning and Community Right-to-Know Act
of 1986.
Statement of Work means that portion of a grant that describes the
purpose and scope of activities and tasks to be carried out as part of
the proposed project.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001]
Sec. 110.30 Grant application.
(a) General. An applicant for a planning or training grant shall use
only the standard application forms approved by the Office of Management
and Budget (OMB) (SF-424 and SF-424A) under the Paperwork Reduction Act
of 1980 (44 U.S.C. 3502). Applicants are required to submit an original
and two copies of the application package to: Grants Manager, Research
and Special Programs Administration, U.S. Department of Transportation,
400 7th Street, SW., Washington, DC 20590-0001. Applications received on
or before January 1st and July 1st of each year will be considered in
that cycle of the semi-annual review and award process. An initial round
of the review and award process will consider applications received on
or before November 15, 1992. Requests and continuation applications must
include an original and two copies of the affected pages; previously
submitted pages with information that is still current do not have to be
resubmitted. The application must include the following:
(1) Application for Federal Assistance for non-construction programs
(SF-424) and Budget sheets (SF-424A). A single application may be used
for both planning and training if the budgets for each are entered
separately on all budget sheets.
(2) For States, a letter from the Governor designating the State
agency that is authorized to apply for a grant and to provide the
written certifications required to receive a grant.
(3) For Indian tribes, a letter from the tribal government,
governing body, or tribal council to the effect that the applicant is
authorized to apply for a grant and to provide the written
certifications required to receive a grant.
(4) A written statement explaining whether the State or tribe
assesses and collects fees on the transportation of hazardous materials
and whether such assessments or fees are used solely to carry out
purposes related to the transportation of hazardous materials.
(5) A statement designating a project manager and providing the
name, position, address and phone number of that individual who will be
responsible for coordinating the funded activities with other agencies/
organizations.
(6) A project narrative statement of the goals and objectives of the
proposed project, project design, and long range plans. The proposed
grant
[[Page 56]]
project and budget periods may be one or more years.
(7) A statement of work in support of the proposed project that
describes and sets priorities for the activities and tasks to be
conducted, the costs associated with each activity, the number and types
of deliverables and products to be completed, and a schedule for
implementation.
(8) A description of the major items of costs needed to implement
the statement of work and a copy of any cost or price analysis if
conducted.
(9) Drug-Free Workplace Certification. The applicant must certify as
specified in appendix C of 49 CFR part 29 that it will comply with the
Drug-Free Workplace Act of 1988 (Pub. L. 100-690, title V, subtitle D;
51 U.S.C. 701 et seq.).
(10) Anti-Lobbying Certification. The applicant must certify as
specified in appendix A of 49 CFR part 20 that no Federal funds will be
expended to pay any person for influencing or attempting to influence an
officer or employee of any agency, a Member of Congress, an officer or
employee of Congress, or an employee of a Member of Congress (section
319 of Pub. L. 101-121, 31 U.S.C. 1352).
(11) Debarment and Suspension Certification. The applicant must
certify as specified in subpart G of 49 CFR part 29 that it will not
make an award or permit any award to any party which is debarred or
suspended or is otherwise excluded from or ineligible for participation
in Federal assistance programs.
(b) Planning. In addition to the requirements specified in paragraph
(a) of this section, eligible State applicants must include the
following in their application package:
(1) A written certification that the State is complying with
sections 301 and 303 of the Emergency Planning and Community Right-to-
Know Act of 1986, including a brief explanation of how compliance has
been achieved.
(2) A written statement specifying the aggregate expenditure of
funds of the State, exclusive of Federal funds, for each of its last two
fiscal years for developing, improving, and implementing emergency plans
under the Emergency Planning and Community Right-to-Know Act of 1986,
including an explanation specifying the sources of these funds. A
written certification that the State's aggregate expenditures, as
defined by the State, of funds for this purpose, exclusive of Federal
funds, will not fall below the average level of its expenditures for its
last two fiscal years. The applicant may not claim any of these
expenditures for cost-sharing.
(3) A written statement agreeing to make at least 75 percent of the
Federal funds awarded available to LEPCs and an explanation of how the
applicant intends to make such funds available to them for developing,
improving, or implementing emergency plans.
(4) Designation of a project manager to serve as contact for
coordinating planning funds under this program.
(5) A project narrative statement of the goals and objectives of
each proposed project, including the following:
(i) A background statement describing the applicant's long-term
goals and objectives with respect to:
(A) The current abilities and authorities of the applicant's program
for preparedness planning;
(B) The need to sustain or increase program capability;
(C) Current degree of participation in or intention to assess the
need for a regional hazardous materials emergency response team; and
(D) The impact that the grant will have on the program.
(ii) A discussion of whether the applicant's program currently
knows, or intends to assess, transportation flow patterns of hazardous
materials within the State and between that State and another State.
(iii) A schedule for implementing the proposed grant activities.
(iv) A statement describing the ways in which planning will be
monitored by the project manager.
(v) A statement indicating that all members of the State Emergency
Response Commission were provided the opportunity to review the grant
application.
(c) Training. In addition to the requirements specified in paragraph
(a) of this section, eligible State and Indian tribe applicants must
include the following in their application package:
(1) For a State applicant, a written certification explaining how
the State
[[Page 57]]
is complying with sections 301 and 303 of the Emergency Planning and
Community Right-to-Know Act.
(2) A written statement specifying the aggregate expenditure of
funds of the State or Indian tribe, exclusive of Federal funds, for each
of its last two fiscal years for training public sector employees to
respond to accidents and incidents involving hazardous materials,
including an explanation specifying the sources of these funds. A
written certification that the applicant's aggregate expenditure, as
defined by the State or tribe, of funds for this purpose, exclusive of
Federal funds, will not fall below the average level of its expenditures
for its last two fiscal years. The applicant may not claim any of these
expenditures for cost-sharing purposes.
(3) For a State applicant, a written statement agreeing to make at
least 75 percent of the Federal funds awarded available for the purpose
of training public sector employees employed or used by political
subdivisions. A State applicant may elect to pass all or some portion of
the grant on to political subdivisions for this purpose. The applicant
must include a specific explanation of how it intends to meet this
requirement.
(4) Designation of a primary point of contact for coordinating
training funded under this program. Identification of a single
repository for copies of course materials delivered under the grant as
specified in Sec. 110.90 of this part.
(5) A project narrative statement of the long-range goals and
objectives of each proposed project, including the following:
(i) A background statement describing:
(A) The current hazardous materials training program(s);
(B) Training audience, including numbers and levels of training and
accreditation program for each level or criterion required to advance to
the next level;
(C) Estimated total number of persons to be trained under the
proposed project;
(D) The ways in which training grants will support the integrated
delivery of training to meet the needs of individualized geographic and
resource needs and time considerations of local responders. When
appropriate, a statement describing how the proposed project will
accommodate the different training needs for rural versus urban
environments; and
(E) The impact that the grant and the National Curriculum will have
on the program.
(ii) A statement describing how the National Curriculum will be used
or modified to train public sector employees at the local level to
respond to accidents and incidents involving hazardous materials.
(iii) A statement describing the ways in which effectiveness of
training will be monitored by the project manager, including, but not
limited to, examinations, critiques, and instructor evaluations.
(iv) A schedule for implementing the proposed training grant
activities.
(v) A statement indicating that all members of the State or Tribal
Emergency Response Commission were provided the opportunity to review
the grant application.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59
FR 49132, Sept. 26, 1994]
Sec. 110.40 Activities eligible for funding.
(a) Planning. Eligible State applicants may receive funding for the
following activities:
(1) Development, improvement, and implementation of emergency plans
required under the Emergency Planning and Community Right-to-Know Act of
1986, as well as exercises which test the emergency plan. Enhancement of
emergency plans to include hazard analysis as well as response
procedures for emergencies involving transportation of hazardous
materials, including radioactive materials.
(2) An assessment to determine flow patterns of hazardous materials
within a State, between a State and another State or Indian country, and
development and maintenance of a system to keep such information
current.
(3) An assessment of the need for regional hazardous materials
emergency response teams.
(4) An assessment of local response capabilities.
[[Page 58]]
(5) Conduct of emergency response drills and exercises associated
with emergency preparedness plans.
(6) Provision of technical staff to support the planning effort.
(7) Additional activities the Associate Administrator deems
appropriate to implement the scope of work for the proposed project plan
and approved in the grant.
(b) Training. Eligible State and Indian tribe applicants may receive
funding for the following activities:
(1) An assessment to determine the number of public sector employees
employed or used by a political subdivision who need the proposed
training and to select courses consistent with the National Curriculum.
(2) Delivery of comprehensive preparedness and response training to
public sector employees. Design and delivery of preparedness and
response training to meet specialized needs. Financial assistance for
trainees and for the trainers, if appropriate, such as tuition, travel
expenses to and from a training facility, and room and board while at
the training facility.
(3) Emergency response drills and exercises associated with
training, a course of study, and tests and evaluation of emergency
preparedness plans.
(4) Expenses associated with training by a person (including a
department, agency, or instrumentality of a State or political
subdivision thereof or an Indian tribe) and activities necessary to
monitor such training including, but not limited to examinations,
critiques and instructor evaluations.
(5) Provision of staff to manage the training effort designed to
result in increased benefits, proficiency, and rapid deployment of local
and regional responders.
(6) Additional activities the Associate Administrator deems
appropriate to implement the scope of work for the proposed project and
approved in the grant.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377,
Aug. 28, 2001]
Sec. 110.50 Disbursement of Federal funds.
(a) Preaward expenditures may not be reimbursed.
(b) Reimbursement may not be made for a project plan unless approved
in the grant award.
(c) If a recipient agency seeks additional funds, the amendment
request will be evaluated on the basis of needs, performance and
availability of funds. An existing grant is not a commitment of future
Federal funding.
Sec. 110.60 Cost sharing for planning and training.
(a) The recipient agency must provide 20 percent of the direct and
indirect costs of all activities covered under the grant award program
with non-Federal funds. Recipients may either use cash (hard-match), in-
kind (soft-match) contributions, or a combination of in-kind plus hard-
match to meet this requirement. In-kind (soft-match) contributions are
in addition to the maintenance of effort required of recipients of grant
awards. The types of contributions allowed are as follows:
(1) Any funds from a State, local, or other non-Federal source used
for an eligible activity as defined in Sec. 110.40 in this part.
(2) The dollar equivalent value of an eligible activity as defined
in Sec. 110.40 of this part provided by a State, local, or other non-
Federal source.
(3) The value of participants' salary while attending a planning or
training activity contained in the approved grant application provided
by a State, local, or other non-Federal source.
(4) Additional types of in-kind contributions the Associate
Administrator deems appropriate.
(b) Funds used for matching purposes under any other Federal grant
or cooperative agreement may not be used for matching purposes. The
funds expended by a recipient agency to qualify for the grant may not be
used for cost-sharing purposes.
(c) Acceptable contributions for matching and cost sharing purposes
must conform to 49 CFR part 18.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001]
Sec. 110.70 Financial administration.
(a) A State must expend and account for grant funds in accordance
with
[[Page 59]]
State laws and procedures for expending and accounting for its own
funds. Fiscal control and accounting procedures of the State, as well as
its subgrantees and cost-type contractors, must be sufficient to:
(1) Permit the preparation of reports required by 49 CFR part 18 and
this part, including the tracing of funds provided for planning to a
level of expenditure adequate to establish that at least 75 percent of
the funds provided were made available to LEPCs for developing,
improving, and implementing emergency plans; and the tracing of funds
provided for training to a level of expenditure adequate to establish
that at least 75 percent of the funds provided were made available for
the purposes of training public sector employees employed or used by
political subdivisions.
(2) Permit the tracing of funds to a level of expenditure adequate
to establish that such funds have not been used in violation of the
restrictions and prohibitions of applicable statutes.
(b) The financial management systems of Indian tribes and any
subgrantees must meet the standards of 49 CFR 18.20, including the
ability to trace funds provided for training to a level of expenditure
adequate to establish that at least 75 percent of the funds provided
were made available for the purposes of training public sector employees
employed or used by political subdivisions.
(c) Advances shall be made to States and Indian tribes consistent
with 49 CFR part 18 and 31 CFR part 205. The Associate Administrator
shall base these advances on demonstrated need, which will be determined
on a case-by-case basis, considering such factors as State/Tribal budget
constraints and reductions in amounts budgeted for hazardous materials
activities. To obtain an advance, a State or Indian tribe must comply
with the following requirements:
(1) A letter from the Governor or Tribal leader or their designee is
required specifying the extenuating circumstances requiring the funding
advance for the grant;
(2) The maximum advance request may not be more than $25,000 for
each State or Indian tribe;
(3) Recipients of advance funding must obligate those funds within 3
months of receipt;
(4) Advances including interest will be deducted from the initial
reimbursement to the State or Indian tribe; and
(5) The State or Indian tribe will have its allocation of current
grant funds reduced and will not be permitted to apply for future grant
funds until the advance is covered by a request for reimbursement. For
example, if $25,000 is advanced for personnel costs, this advance would
be deducted from the initial reimbursement in the year the advance was
made.
(d) To be allowable, costs must be eligible, reasonable, necessary,
and allocable to the approved project in accordance with OMB Circular A-
87 and included in the grant award. Costs incurred prior to the award of
any grant are not allowable. Recipient agencies are responsible for
obtaining audits in accordance with the Single Audit Act of 1984 (31
U.S.C. 7501), 49 CFR part 90, and OMB Circular A-128. Audits shall be
made by an independent auditor in accordance with generally accepted
government auditing standards covering financial and compliance audits.
The Associate Administrator may audit a recipient agency at any time.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377,
Aug. 28, 2001]
Sec. 110.80 Procurement.
Project managers shall use procurement procedures and practices
which reflect applicable State laws and regulations and Federal
requirements as specified in 49 CFR 18.36.
Sec. 110.90 Grant monitoring, reports, and records retention.
(a) Grant monitoring. Project managers are responsible for managing
the day-to-day operations of grant, subgrant and contract-supported
activities. Project managers must monitor performance of supported
activities to assure compliance with applicable Federal requirements and
achievement of performance goals. Monitoring must cover each program,
function, activity, or task covered by the grant. Monitoring and
reporting requirements for planning and training are contained
[[Page 60]]
in this part; general grant reporting requirements are specified in 49
CFR 18.40.
(b) Reports. (1) The project manager shall submit a performance
report at the completion of an activity for which reimbursement is being
requested or with a request to amend the grant. The final performance
report is due 90 days after the expiration or termination of the grant.
(2) Project managers shall submit an original and two copies of all
performance reports. Performance reports for planning and training must
include comparison of actual accomplishments to the stated goals and
objectives established for the performance period, and the reasons for
not achieving those goals and objectives, if applicable.
(3) Project managers shall report developments or events that occur
between the required performance reporting dates which have significant
impact upon the planning and training activity such as:
(i) Problems, delays, or adverse conditions which will impair the
ability to meet the objective of the grant; and
(ii) Favorable developments which enable meeting time schedules and
objectives sooner or at less cost than anticipated or producing more
beneficial results than originally planned.
(4) Financial reporting, except as provided in Sec. 110.70 and 49
CFR 18.41, shall be supplied quarterly using Standard Form 270, Request
for Advance or Reimbursement, to report the status of funds. The project
manager shall report separately on planning and training.
(c) Records retention. In accordance with 49 CFR 18.42, all
financial and programmatic records, supporting documents, statistical
records, training materials, and other documents generated under a grant
shall be maintained by the project manager for three years from the date
the project manager submits the final financial status report (SF 269)
or Request for Advance or Reimbursement (SF 270). The project manager
shall designate a repository and single-point of contact for planning
and for training, or both, for these purposes. If any litigation, claim,
negotiation, audit or other action involving the records has been
started before the expiration of the 3-year period, the records must be
retained until completion of the action and resolution of all issues
which arise from it, or until the end of the regular 3-year period,
whichever is later.
Sec. 110.100 Enforcement.
If a recipient agency fails to comply with any term of an award
(whether stated in a Federal statute or regulation, an assurance, a
State plan or application, a notice of award, or elsewhere) a
noncompliance action may be taken as specified in 40 CFR 18.43. The
recipient agency may appeal any such actions as specified in 49 CFR part
18. Costs incurred by the recipient agency during a suspension or after
termination of an award are not allowable unless the Associate
Administrator authorizes it in writing. Grant awards may be terminated
in whole or in part with the consent of the recipient at any agreed upon
effective date, or by the recipient upon written notification.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377,
Aug. 28, 2001]
Sec. 110.110 After-grant requirements.
The Associate Administrator will close out the award upon
determination that all applicable administrative actions and all
required work of the grant are complete in accordance with subpart D of
49 CFR part 18. The project manager must submit all financial,
performance, and other reports required as a condition of the grant,
within 90 days after the expiration or termination of the grant. This
time frame may be extended by the Associate Administrator for Hazardous
Materials Safety for cause.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377,
Aug. 28, 2001]
Sec. 110.120 Deviation from this part.
Recipient agencies may request a deviation from the non-statutory
provisions of this part. The Associate Administrator will respond to
such requests in writing. If appropriate, the decision will be included
in the grant agreement. Request for deviations from part 110 must be
submitted to: Grants
[[Page 61]]
Manager, Research and Special Programs Administration, U.S. Department
of Transportation, 400 7th Street, SW., Washington, DC 20590-0001.
[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001]
Sec. 110.130 Disputes.
Disputes should be resolved at the lowest level possible, beginning
with the project manager and the project officer. If an agreement cannot
be reached, the Administrator, RSPA, will serve as the dispute
resolution official, whose decision will be final.
[[Page 62]]
SUBCHAPTER B--OIL TRANSPORTATION
PART 130--OIL SPILL PREVENTION AND RESPONSE PLANS--Table of Contents
Sec.
130.1 Purpose.
130.2 Scope.
130.3 General requirements.
130.5 Definitions.
130.11 Communication requirements.
130.21 Packaging requirements.
130.31 Response plans.
130.33 Response plan implementation.
Authority: 33 U.S.C. 1321.
Source: Amdt. 130-2, 61 FR 30541, June 17, 1996, unless otherwise
noted.
Sec. 130.1 Purpose.
This part prescribes prevention, containment and response planning
requirements of the Department of Transportation applicable to
transportation of oil by motor vehicles and rolling stock.
Sec. 130.2 Scope.
(a) The requirements of this part apply to--
(1) Any liquid petroleum oil in a packaging having a capacity of
3,500 gallons or more; and
(2) Any liquid petroleum or non-petroleum oil in a quantity greater
than 42,000 gallons per packaging.
(b) The requirements of this part have no effect on--
(1) The applicability of the Hazardous Materials Regulations set
forth in subchapter C of this chapter; and
(2) The discharge notification requirements of the United States
Coast Guard (33 CFR part 153) and EPA (40 CFR part 110).
(c) The requirements of this part do not apply to--
(1) Any mixture or solution in which oil is in a concentration by
weight of less than 10 percent.
(2) Transportation of oil by aircraft or vessel.
(3) Any petroleum oil carried in a fuel tank for the purpose of
supplying fuel for propulsion of the transport vehicle to which it is
attached.
(4) Oil transport exclusively within the confines of a non-
transportation-related or terminal facility in a vehicle not intended
for use in interstate or intrastate commerce (see 40 CFR part 112,
appendix A).
(d) The requirements in Sec. 130.31(b) of this part do not apply to
mobile marine transportation-related facilities (see 33 CFR part 154).
Sec. 130.3 General requirements.
No person may offer or accept for transportation or transport oil
subject to this part unless that person--
(a) Complies with this part; and
(b) Has been instructed on the applicable requirements of this part.
Sec. 130.5 Definitions.
In this subchapter: Animal fat means a non-petroleum oil, fat, or
grease derived from animals, not specifically identified elsewhere in
this part.
Contract or other means is:
(1) A written contract with a response contractor identifying and
ensuring the availability of the necessary personnel or equipment within
the shortest practicable time;
(2) A written certification by the owner or operator that the
necessary personnel or equipment can and will be made available by the
owner or operator within the shortest practicable time; or
(3) Documentation of membership in an oil spill response
organization that ensures the owner's or operator's access to the
necessary personnel or equipment within the shortest practicable time.
EPA means the U.S. Environmental Protection Agency.
Liquid means a material that has a vertical flow of over two inches
(50 mm) within a three-minute period, or a material having one gram or
more liquid separation, when determined in accordance with the
procedures specified in ASTM D 4359-84, ``Standard Test Method for
Determining Whether a Material is a Liquid or a Solid,'' 1990 edition,
which is incorporated by reference.
Note: This incorporation by reference has been approved by the
Director of the Federal Register in accordance with 5 U.S.C. 552(a) and
1 CFR part 51. A copy may be obtained
[[Page 63]]
from the American Society for Testing and Materials, 1916 Race Street,
Philadelphia, PA 19103. Copies may be inspected at the RSPA Records
Center, Room 8421, DOT headquarters building, 400 7th St. SW,
Washington, DC 20590 or at the Office of the Federal Register, 800 North
Capitol St. NW, Room 700, Washington, DC.
Maximum extent practicable means the limits of available technology
and the practical and technical limits on an owner or operator of an
onshore facility in planning the response resources required to provide
the on-water recovery capability and the shoreline protection and
cleanup capability to conduct response activities for a worst-case
discharge of oil in adverse weather.
Non-petroleum oil means any animal fat, vegetable oil or other non-
petroleum oil.
Oil means oil of any kind or in any form, including, but not limited
to, petroleum, fuel oil, sludge, oil refuse, and oil mixed with wastes
other than dredged spoil.
Note: This definition does not include hazardous substances (see 40
CFR part 116).
Other non-petroleum oil means a non-petroleum oil of any kind that
is not an animal fat or vegetable oil.
Packaging means a receptacle and any other components or materials
necessary for the receptacle to perform its containment function in
conformance with the packaging requirements of this part. A
compartmented tank is a single packaging.
Person means an individual, firm, corporation, partnership,
association, State, municipality, commission, or political subdivision
of a State, or any interstate body, as well as a department, agency, or
instrumentality of the executive, legislative or judicial branch of the
Federal Government.
Petroleum oil means any oil extracted or derived from geological
hydrocarbon deposits, including fractions thereof.
Qualified individual means an individual familiar with the response
plan, trained in his or her responsibilities in implementing the plan,
and authorized, on behalf of the owner or operator, to initiate all
response activities identified in the plan, to enter into response-
related contracts and obligate funds for such contracts, and to act as a
liaison with the on-scene coordinator and other responsible officials.
The qualified individual must be available at all times the owner or
operator is engaged in transportation subject to part 130 (alone or in
conjunction with an equally qualified alternate), must be fluent in
English, and must have in his or her possession documentation of the
required authority.
Transports or Transportation means any movement of oil by highway or
rail, and any loading, unloading, or storage incidental thereto.
Vegetable oil means a non-petroleum oil or fat derived from plant
seeds, nuts, kernels or fruits, not specifically identified elsewhere in
this part.
Worst-case discharge means ``the largest foreseeable discharge in
adverse weather conditions,'' as defined at 33 U.S.C. 1321(a)(24). The
largest foreseeable discharge from a motor vehicle or rail car is the
capacity of the cargo container. The term ``maximum potential
discharge,'' used in Sec. 130.31(a), is synonymous with ``worst-case
discharge.''
[Amdt. 130-2, 61 FR 30541, June 17, 1996, as amended by 66 FR 45378,
Aug. 28, 2001]
Sec. 130.11 Communication requirements.
(a) No person may offer oil subject to this part for transportation
unless that person provides the person accepting the oil for
transportation a document indicating the shipment contains oil.
(b) No person may transport oil subject to this part unless a
readily available document indicating that the shipment contains oil is
in the possession of the transport vehicle operator during
transportation.
(c) A material subject to the requirements of this part need not be
specifically identified as oil when the shipment document accurately
describes the material as: aviation fuel, diesel fuel, fuel oil,
gasoline, jet fuel, kerosene, motor fuel, or petroleum.
Sec. 130.21 Packaging requirements.
Each packaging used for the transportation of oil subject to this
part must be designed, constructed, maintained, closed, and loaded so
that, under conditions normally incident to transportation, there will
be no release of oil to the environment.
[[Page 64]]
Sec. 130.31 Response plans.
(a) After September 30, 1993, no person may transport oil subject to
this part unless that person has a current basic written plan that:
(1) Sets forth the manner of response to discharges that may occur
during transportation;
(2) Takes into account the maximum potential discharge of the
contents from the packaging;
(3) Identifies private personnel and equipment available to respond
to a discharge;
(4) Identifies the appropriate persons and agencies (including their
telephone numbers) to be contacted in regard to such a discharge and its
handling, including the National Response Center; and
(5) For each motor carrier, is retained on file at that person's
principal place of business and at each location where dispatching of
motor vehicles occurs; and for each railroad, is retained on file at
that person's principal place of business and at the dispatcher's
office.
(b) After February 18, 1993, no person may transport an oil subject
to this part in a quantity greater than 1,000 barrels (42,000 gallons)
unless that person has a current comprehensive written plan that:
(1) Conforms with all requirements specified in paragraph (a) of
this section;
(2) Is consistent with the requirements of the National Contingency
Plan (40 CFR part 300) and Area Contingency Plans;
(3) Identifies the qualified individual having full authority to
implement removal actions, and requires immediate communications between
that individual and the appropriate Federal official and the persons
providing spill response personnel and equipment;
(4) Identifies, and ensures by contract or other means the
availability of, private personnel (including address and phone number),
and the equipment necessary to remove, to the maximum extent
practicable, a worst case discharge (including a discharge resulting
from fire or explosion) and to mitigate or prevent a substantial threat
of such a discharge;
(5) Describes the training, equipment testing, periodic unannounced
drills, and response actions of facility personnel, to be carried out
under the plan to ensure the safety of the facility and to mitigate or
prevent the discharge, or the substantial threat of such a discharge;
and
(6) Is submitted, and resubmitted in the event of any significant
change, to the Federal Railroad Administrator (for tank cars), or to the
Federal Highway Administrator (for cargo tanks) at 400 Seventh Street
SW, Washington, DC 20590-0001.
(Approved by the Office of Management and Budget under control number
2137-0591)
Sec. 130.33 Response plan implementation.
If, during transportation of oil subject to this part, a discharge
occurs-- into or on the navigable waters of the United States; on the
adjoining shorelines to the navigable waters; or that may affect natural
resources belonging to, appertaining to, or under the exclusive
management authority of, the United States--the person transporting the
oil shall implement the plan required by Sec. 130.31, in a manner
consistent with the National Contingency Plan, 40 CFR part 300, or as
otherwise directed by the Federal on-scene coordinator.
[[Page 65]]
SUBCHAPTER C--HAZARDOUS MATERIALS REGULATIONS
PART 171--GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS--Table of Contents
Sec.
171.1 Purpose and scope.
171.2 General requirements.
171.3 Hazardous waste.
171.4 Marine pollutants.
171.6 Control numbers under the Paperwork Reduction Act.
171.7 Reference material.
171.8 Definitions and abbreviations.
171.9 Rules of construction.
171.10 Units of measure.
171.11 Use of ICAO Technical Instructions.
171.12 Import and export shipments.
171.12a Canadian shipments and packagings.
171.14 Transitional provisions for implementing certain requirements.
171.15 Immediate notice of certain hazardous materials incidents.
171.16 Detailed hazardous materials incident reports.
171.17-171.18 [Reserved]
171.19 Approvals or authorizations issued by the Bureau of Explosives.
171.20 Submission of Examination Reports.
171.21 Assistance in investigations and special studies.
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
Sec. 171.1 Purpose and scope.
(a) This subchapter prescribes requirements of the Department
governing--
(1) The offering of hazardous materials for transportation and
transportation of hazardous materials in interstate, intrastate, and
foreign commerce by rail car, aircraft, motor vehicle, and vessel
(except as delegated at Sec. 1.46(t) of this title).
(2) The representation that a hazardous material is present in a
package, container, rail car, aircraft, motor vehicle, or vessel.
(3) The manufacture, fabrication, marking, maintenance,
reconditioning, repairing, or testing of a packaging or container which
is represented, marked, certified, or sold for use in transportation of
hazardous materials.
(4) The use of terms and symbols prescribed in this subchapter for
the marking, labeling, placarding and description of hazardous materials
and packagings used in their transport.
(b) Any person who, under contract with any department, agency, or
instrumentality of the executive, legislative, or judicial branch of the
Federal Government, transports, or causes to be transported or shipped,
a hazardous material or manufactures, fabricates, marks, maintains,
reconditions, repairs, or tests a package or container which is
represented, marked, certified, or sold by such person as qualified for
use in the transportation of a hazardous material shall be subject to
and comply with all provisions of the Federal hazardous materials
transportation law, all orders and regulations issued thereunder, and
all other substantive and procedural requirements of Federal, State, and
local governments and Indian tribes (except any such requirements that
have been preempted by the Federal hazardous materials transportation
law or any other Federal law), in the same manner and to the same extent
as any person engaged in such activities that are in or affect commerce
is subject to such provisions, orders, regulations, and requirements.
(c) Any person who knowingly violates a requirement of the Federal
hazardous material transportation law, an order issued thereunder,
subchapter A, an exemption issued under subchapter A, of this
subchapter, is liable for a civil penalty of not more than $25,000
($27,500 for a violation that occurs after January 21, 1997) and not
less than $250 for each violation. When the violation is a continuing
one and involves the transporting of hazardous materials or the causing
of them to be transported or shipped, each day of the violation
constitutes a separate offense. Any person who knowingly violates
Sec. 171.2(g) of this subchapter or willfully violates a provision of
the Federal hazardous material transportation law or an order or
regulation issued thereunder shall be fined under Title 18, United
States
[[Page 66]]
Code, or imprisoned for not more than 5 years, or both.
[Amdt. 171-150, 62 FR 1215, Jan. 8, 1997, as amended by Amdt. 171-152,
62 FR 2977, Jan. 21, 1997; Amdt. 171-154, 62 FR 49566, Sept. 22, 1997;
65 FR 58618, Sept. 29, 2000; 66 FR 45378, Aug. 28, 2001]
Sec. 171.2 General requirements.
(a) No person may offer or accept a hazardous material for
transportation in commerce unless that person is registered in
conformance with subpart G of part 107 of this chapter, if applicable,
and the hazardous material is properly classed, described, packaged,
marked, labeled, and in condition for shipment as required or authorized
by applicable requirements of this subchapter, or an exemption, approval
or registration issued under this subchapter or subchapter A of this
chapter.
(b) No person may transport a hazardous material in commerce unless
that person is registered in conformance with subpart G of part 107 of
this chapter, if applicable, and the hazardous material is handled and
transported in accordance with applicable requirements of this
subchapter, or an exemption, approval or registration issued under this
subchapter or subchapter A of this chapter.
(c) No person may represent, mark, certify, sell, or offer a
packaging or container as meeting the requirements of this subchapter or
an exemption, approval or registration issued under this subchapter or
subchapter A of this chapter, governing its use in the transportation in
commerce of a hazardous material, whether or not it is used or intended
to be used for the transportation of a hazardous material, unless the
packaging or container is manufactured, fabricated, marked, maintained,
reconditioned, repaired and retested, as appropriate, in accordance with
applicable requirements of this subchapter, or an exemption, approval or
registration issued under this subchapter or subchapter A of this
chapter.
(d) The representations, markings, and certifications subject to the
prohibitions of paragraph (c) of this section include, but are not
limited to--
(1) Specification identifications that include the letters ``ICC,''
``DOT,'' ``CTC,'' ``MC,'' or ``UN'';
(2) Exemption, approval, and registration numbers that include the
letters ``DOT,'' ``EX,'' ``M,'' or ``R''; and
(3) Test dates associated with specification, registration,
approval, retest or exemption markings indicating compliance with a test
or retest requirement of this subchapter, or an exemption, an approval
or a registration issued under this subchapter or subchapter A of this
chapter.
(e) When a person performs a function covered by or having an effect
on a specification prescribed in part 178, 179 or 180 of this
subchapter, an approval issued under this subchapter, or an exemption
issued under subpart B of this chapter, that person must perform the
function in accordance with that specification, approval, or exemption,
as appropriate.
(f) No person shall, by marking or otherwise, represent that--
(1) A container or package for the transportation of hazardous
materials is safe, certified, or in compliance with the requirements of
this title unless it meets the requirements of all applicable
regulations issued under the Federal hazardous material transportation
law; or
(2) A hazardous material is present in a package, container, motor
vehicle, rail car, aircraft, or vessel, if the hazardous material is not
present.
(g) No person shall unlawfully alter, remove, deface, destroy, or
otherwise tamper with--
(1) Any marking, label, placard, or description on a document
required by the Federal hazardous material transportation law, or the
regulations issued thereunder; or
(2) Any package, container, motor vehicle, rail car, aircraft, or
vessel used for the transportation of hazardous materials.
(h) No person shall--
(1) Falsify or alter an exemption, approval, registration or other
grant of authority issued under this subchapter or subchapter A of this
chapter; or
(2) Offer a hazardous material for transportation or transport a
hazardous material in commerce, or represent, mark, certify, or sell a
packaging or container, under a false or altered exemption, approval,
registration or other grant of authority issued
[[Page 67]]
under this subchapter or subchapter A of this chapter.
[Amdt. 171-70, 48 FR 2655, Jan. 20, 1983, as amended by Amdt. No. 171-
100, 54 FR 25004, June 12, 1989; Amdt. 171-12, 56 FR 8624, Feb. 28,
1991; Amdt. No. 171-115, 57 FR 30631, July 9, 1992; 57 FR 37902, Aug.
21, 1992; Amdt. No. 171-120, 58 FR 33305, June 16, 1993; Amdt. 171-2, 59
FR 49132, Sept. 26, 1994; Amdt. 171-141, 61 FR 21101, May 9, 1996; 64 FR
10752, Mar. 5, 1999]
Sec. 171.3 Hazardous waste.
(a) No person may offer for transportation or transport a hazardous
waste (as defined in Sec. 171.8 of this subchapter) in interstate or
intrastate commerce except in accordance with the requirements of this
subchapter.
(b) No person may accept for transportation, transport, or deliver a
hazardous waste for which a manifest is required unless that person:
(1) Has marked each motor vehicle used to transport hazardous waste
in accordance with Sec. 390.21 or Sec. 1058.2 of this title even though
placards may not be required;
(2) Complies with the requirements for manifests set forth in
Sec. 172.205 of this subchapter; and
(3) Delivers, as designated on the manifest by the generator, the
entire quantity of the waste received from the generator or a
transporter to:
(i) The designated facility or, if not possible, to the designated
alternate facility;
(ii) The designated subsequent carrier; or
(iii) A designated place outside the United States.
Note: Federal law specifies penalties up to $250,000 fine for an
individual and $500,000 for a company and 5 years imprisonment for the
willful discharge of hazardous waste at other than designated
facilities. 49 U.S.C. 5124.
(c) If a discharge of hazardous waste or other hazardous material
occurs during transportation, and an official of a State or local
government or a Federal agency, acting within the scope of his official
responsibilities, determines that immediate removal of the waste is
necessary to prevent further consequence, that official may authorize
the removal of the waste without the preparation of a manifest. [Note:
In such cases, EPA does not require carriers to have EPA identification
numbers.]
Note 1: EPA requires shippers (generators) and carriers
(transporters) of hazardous wastes to have identification numbers which
must be displayed on hazardous waste manifests. See 40 CFR parts 262 and
263. (Identification number application forms may be obtained from EPA
regional offices.)
Note 2: In 40 CFR part 263, the EPA sets forth requirements for the
cleanup of releases of hazardous wastes.
[Amdt. 171-53, 45 FR 34586, May 22, 1980, as amended by Amdt. 171-53, 45
FR 74648, Nov. 10, 1980; Amdt. 171-78, 49 FR 10510, Mar. 20, 1984; Amdt.
171-107, 54 FR 40068, Sept. 29, 1989; Amdt. 171-111, 55 FR 52466, Dec.
21, 1990; 56 FR 66157, Dec. 20, 1991; Amdt. 171-2, 59 FR 49132, Sept.
26, 1994; Amdt. 171-141, 61 FR 21102, May 9, 1996]
Sec. 171.4 Marine pollutants.
(a) Except as provided in paragraph (c) of this section, no person
may offer for transportation or transport a marine pollutant, as defined
in Sec. 171.8, in intrastate or interstate commerce except in accordance
with the requirements of this subchapter.
(b) The requirements of this subchapter for the transportation of
marine pollutants are based on the provisions of Annex III of the 1973
International Convention for Prevention of Pollution from Ships, as
modified by the Protocol of 1978 (MARPOL 73/78).
(c) Exceptions. Except when transported aboard vessel, the
requirements of this subchapter specific to marine pollutants do not
apply to non-bulk packagings transported by motor vehicles, rail cars or
aircraft.
[Amdt. 171-116, 57 FR 52934, Nov. 5, 1993, as amended by Amdt. 107-39,
61 FR 51337, Oct. 1, 1996]
Sec. 171.6 Control numbers under the Paperwork Reduction Act.
(a) Purpose and scope. This section collects and displays the
control numbers assigned to the HMR collections of information by the
Office of Management and Budget (OMB) under the Paperwork Reduction Act
of 1995. This section complies with the requirements of 5 CFR 1320.7(f),
1320.12, 1320.13 and 1320.14 (OMB regulations implementing the Paperwork
Reduction Act of 1995)
[[Page 68]]
for the display of control numbers assigned by OMB to collections of
information of the HMR.
(b) OMB control numbers. The table in paragraph (b)(2) of this
section sets forth the control numbers assigned to collection of
information in the HMR by the Office of Management and Budget (OMB)
under the Paperwork Reduction Act of 1995.
(1) Column 1 lists the OMB control number assigned to the HMR
collections of information. Column 2 contains the Report Title of the
approved collection of information. Column 3 lists the part(s) or
section(s) in 49 CFR identified or described in the collection of
information.
(2) Table.
------------------------------------------------------------------------
Title 49 CFR part or
section where
Current OMB control No. Title identified and
described
------------------------------------------------------------------------
2137-0014................. Cargo Tank Secs. 107.503,
Specification 107.504, 178.320,
Requirements. 178.337, 178.338,
178.345, 180.407,
180.409, 180.413,
180.417.
2137-0018................. Inspection and Secs. 173.24,
Testing of Portable 173.32, 173.32a,
Tank and IBC's. 173.32b, 178.3,
178.245, 178.255,
178.270, 178.703,
178.801, 180.352.
2137-0022................. Testing, Inspection, Secs. 173.34,
and Marking 173.302, 173.303,
Requirements for 173.309, 178.2,
Cylinders. 178.3, 178.35,
178.44, 178.45,
178.46, 178.57,
178.59, 178.60,
178.61, 178.68.
2137-0034................. Hazardous Materials Secs. 172.200,
Shipping Papers and 172.201, 172.203,
Emergency Response 172.204, 172.205,
Information. 172.600, 172.602,
172.604, 172.606,
173.6, 173.7,
173.22, 173.56,
174.24, 174.26,
174.114, 175.30,
175.31, 175.33,
175.35, 176.24,
176.27, 176.30,
176.36, 176.89,
177.817.
2137-0039................. Hazardous Materials Secs. 171.15,
Incident Report. 171.16.
2137-0051................. Rulemaking and Secs. 106.31,
Exemptions Petitions. 106.35, 106.38,
107.5, 107.7,
107.105, 107.107,
107.109, 107.113,
107.117, 107.121,
107.123, 107.125,
107.205, 107.211,
107.215, 107.217,
107.219, 107.221,
107.223.
2137-0510................. RAM Transportation Part 173, Subpart I,
Requirements. Secs. 173.22,
173.411, 173.415,
173.416, 173.417,
173.457, 173.471,
173.472, 173.473,
173.476.
2137-0542................. Cryogenic Liquids Secs. 173.318,
Requirements. 177.816, 177.840,
180.405.
2137-0557................. Approvals for Secs. 107.402,
Hazardous Materials. 107.403, 107.405,
107.503, 107.705,
107.713, 107.715,
107.717, 110.30,
172.101, 172.102,
Special provisions:
26, 29, 53, 55, 60,
105, 118, 121, 125,
129, 131, 133, 136;
172.102, Special
provisions: B45,
B55, B61, B69, B77,
B81; N10, N72; Code:
T42; 173.2a, 173.4,
173.7, 173.21,
173.22, 173.24,
173.28, 173.31,
173.32a, 173.32b,
173.34, 173.51,
173.56, 173.58,
173.59, 173.124,
173.128, 173.159,
173.166, 173.171,
173.214, 173.222,
173.224, 173.225,
173.245, 173.300a,
173.300b, 173.301,
173.305, 173.306,
173.314, 173.315,
173.316, 173.318,
173.334, 173.340,
173.411, 173.433,
173.457, 173.471,
173.472, 173.473,
173.476, 174.50,
174.63, 175.10,
175.701, 176.168,
176.340, 176.704,
178.3, 178.35,
178.47, 178.53,
178.58, 178.270-3,
178.270-13, 178.503,
178.509, 178.605,
178.606, 178.608,
178.801, 178.813.
[[Page 69]]
2137-0559................. Rail Carriers and Secs. 172.102,
Tank Car Tank Special provisions:
Requirements. B45, B46, B55, B61,
B69, B77, B78, B81;
173.10, 173.31,
174.20, 174.50,
174.63, 174.104,
174.114, 174.204,
179.3, 179.4, 179.5,
179.6, 179.7,
179.11, 179.18,
179.22, 179.100-9,
179.100-12, 179.100-
13, 179.100-16,
179.100-17, 179.102-
4, 179.102-17,
179.103-1, 179.103-
2, 179.103-3,
179.103-5, 179.200-
10, 179.200-14,
179.200-15, 179.200-
16, 179.200-17,
179.200-19, 179.201-
3, 179.201-8,
179.201-9, 179.220-
4, 179.220-7,
179.220-8, 179.220-
13, 179.220-15,
179.220-17, 179.220-
18, 179.220-20,
179.220-22, 179.300-
3, 179.300-7,
179.300-9, 179.300-
12, 179.300-13,
179.300-15, 179.300-
20, 179.400-3,
179.400-4, 179.400-
11, 179.400-13,
179.400-16, 179.400-
17, 179.400-19,
179.400-20, 179.500-
5, 179.500-8,
179.500-12, 179.500-
18, 180.505,
180.509, 180.515,
180.517.
2137-0572................. Testing Requirements Secs. 178.2,
for Non-Bulk 178.601.
Packaging.
2137-0582................. Container Secs. 176.27,
Certification 176.172.
Statement.
2137-0586................. Hazardous Materials Part 110.
Public Sector
Training and
Planning Grants.
2137-0595................. Cargo Tank Motor Secs. 173.315,
Vehicles in 178.337-8, 178.337-
Liquefied Compressed 9, 180.405, 180.416.
Gas Service.
------------------------------------------------------------------------
[Amdt. 171-111, 56 FR 66157, Dec. 20, 1991, as amended at 57 FR 1877,
Jan. 16, 1992; Amdt. 171-121, 58 FR 51527, Oct. 1, 1993; Amdt. 171-137,
61 FR 33254, June 26, 1996; 62 FR 51558, Oct. 1, 1997; 64 FR 51915,
Sept. 27, 1999; 64 FR 61220, Nov. 10, 1999; 65 FR 58619, Sept. 29, 2000]
Sec. 171.7 Reference material.
(a) Matter incorporated by reference--(1) General. There is
incorporated, by reference in parts 170-189 of this subchapter, matter
referred to that is not specifically set forth. This matter is hereby
made a part of the regulations in parts 170-189 of this subchapter. The
matter subject to change is incorporated only as it is in effect on the
date of issuance of the regulation referring to that matter. The
material listed in paragraph (a)(3) has been approved for incorporation
by reference by the Director of the Federal Register in accordance with
5 U.S.C 552(a) and 1 CFR part 51. Material is incorporated as it exists
on the date of the approval and a notice of any change in the material
will be published in the Federal Register. Matters referenced by
footnote are included as part of the regulations of this subchapter.
(2) Accessibility of materials. All incorporated matter is available
for inspection at:
(i) The RSPA Records Center, Room 8421, NASSIF Building, 400 7th
Street, SW., Washington, DC 20590; and
(ii) The Office of the Federal Register, 800 North Capitol Street,
NW., suite 700, Washington, DC.
(3) Table of material incorporated by reference. The following table
sets forth material incorporated by reference. The first column lists
the name and address of the organization from which the material is
available and the name of the material. The second column lists the
section(s) of this subchapter, other than Sec. 171.7, in which the
matter is referenced. The second column is presented for information
only and may not be all inclusive.
------------------------------------------------------------------------
Source and name of material 49 CFR reference
------------------------------------------------------------------------
Air Transport Association of America, 1301 ......................
Pennsylvania Avenue, N.W., Washington, DC 20004-
1707
ATA Specification No. 300 Packaging of 172.102
Airline Supplies, Revision 19, July 31,
1996.
The Aluminum Association,
420 Lexington Avenue, New York, NY 10017
Aluminum Standards and Data, Seventh Edition, 172.102; 178..46 and
June 1982. 178.65
[[Page 70]]
American National Standards Institute, Inc.,
1430 Broadway, New York, NY 10018
ANSI/ASHRAE 15-94, Safety Code for Mechanical 173.306
Refrigeration.
ANSI B16.5-77, Steel Pipe Flanges, Flanged 178.345; 178.360
Fittings.
ANSI N14.1 Standard for Packaging of Uranium 173.417; 173.420
Hexafluoride for Transport, 1971, 1982, 1987
and 1990 Editions.
American Pyrotechnics Association (APA),
P.O. Box 213, Chestertown, MD 21620
APA Standard 87-1, Standard for Construction and 173.56
Approval for Transportation of Fireworks,
Novelties, and Theatrical Pyrotechnics, January
23, 1998 version.
American Society of Mechanical Engineers,
United Engineering Center, 354 47th Street,
New York, NY 10017
ASME Code, Sections II (Parts A and B), V, VIII 173.32; 173.306;
(Division 1), and IX of 1998 Edition of 173.315; 173.318;
American Society of Mechanical Engineers Boiler 173.420; 178.245;
and Pressure Vessel Code. 178.255; 178.270;
178.271; 178.272;
178.337; 178.338;
178.345; 178.346;
178.347; 178.348;
179.400; 180.407;
180.417
ASME Code, Section V (FR Nondestructive 180.407
Examination), 1977.
ASME Code, Section IX (FR Welding and Brazing 178.245; 178.270;
Qualification), 1977 and Addendum (1979). 178.337; 178.338
American Society for Testing and Materials,
100 Barr Harbor Drive, West Conshohocken, PA
19428
Noncurrent ASTM Standards are available from:
Engineering Societies Library, 354 E. 47th
Street, New York, NY 10017
ASTM A 20/A 20M-93a Standard Specification for 178.337-2; 179.102-4;
General Requirements for Steel Plates for 179.102-17.
Pressure Vessels.
ASTM E 112-96 Standard Test Methods for 178.274
Determining Average Grain Size, 1996 Edition.
ASTM A 47-68 Malleable Iron Castings........... 179.200
ASTM A 240/A 240M-94b Standard Specification for 178.57; 178.358-5;
Heat-Resisting Chromium and Chromium-Nickel 179.100-7; 179.100-
Stainless Steel Plate, Sheet and Strip for 10; 179.102-1;
Pressure Vessels. 179.102-4; 179.102-
17; 179.200-7;
179.201-5; 179.220-7;
179.400-5.
ASTM A 242-81 Standard Specification for High- 179.100
Strength Low-Alloy Structural Steel.
ASTM A 262-93a Standard Practices for Detecting 179.100-7; 179.200-7;
Susceptibility to Intergranular Attack in 179.201-4.
Austenitic Stainless Steels.
ASTM A 300-58 Steel Plates for Pressure Vessels 178.337
for Service at Low Temperatures.
ASTM A 302/A 302M-93 Standard Specification for 179.100-7; 179.200-7;
Pressure Vessel Plates, Alloy Steel, Manganese- 179.220-7.
Molybdenum and Manganese-Molybdenum Nickel.
ASTM A 333-67 Seamless and Welded Steel Pipe 178.45
for Low-Temperature Service.
ASTM A 366/A 366M-91 (1993)e1 Standard 178.601
Specification for Steel, Sheet, Carbon, Cold-
Rolled, Commercial Quality.
ASTM A 370-94 Standard Test Methods and 179.102-1; 179.102-4;
Definitions for Mechanical Testing of Steel 179.102-17.
Products.
ASTM A 388-67 Ultrasonic Testing and Inspection 178.45
of Heavy Steel Forging.
ASTM A 441-81 Standard Specification for High- 178.338
Strength Low-Alloy Structural Manganese
Vanadium Steel.
ASTM A 514-81 Standard Specification for High- 178.338
Yield Strength Quenched and Tempered Alloy
Steel Plate, Suitable for Welding.
ASTM A 516/A 516M-90 Standard Specification for 178.337-2; 179.100-7;
Pressure Vessel Plates, Carbon Steel, for 179.100-20; 179.102-
Moderate and Lower- Temperature Service. 1; 179.102-2; 179.102-
4; 179.102-17;
179.200-7; 179.220-7.
[[Page 71]]
ASTM A 537/A 537M-91 Standard Specification for 179.100-7; 179.102-4;
Pressure Vessel Plates, Heat-Treated, Carbon- 179.102-17.
Manganese-Silicon Steel.
ASTM A 568/A 568M-95 Standard Specification for 178.601
Steel, Sheet, Carbon, and High-Strength, Low-
Alloy, Hot-Rolled and Cold-Rolled, General
Requirements for.
ASTM A 572-82 Standard Specification for High- 178.338; 179.100
Strength Low-Alloy Columbian-Vanadium Steels of
Structural Quality.
ASTM A 588-81 Standard Specification for High- 179.100; 178.338
Strength Low-Alloy Structural Steel with 50 Ksi
Minimum Yield Point to 4 in. Thick.
ASTM A 606-75 Standard Specification for Steel 178.338
Sheet and Strip Hot-Rolled and Cold-Rolled,
High-Strength, Low-Alloy, with Improved
Atmospheric Corrosion Resistance, 1975
(Reapproved 1981).
ASTM A 612-72a High Strength Steel Plates for 178.337
Pressure Vessels for Moderate and Lower
Temperature Service.
ASTM A 633-79a Standard Specification for 178.338
Normalized High-Strength Low-Alloy Structural
Steel, 1979 Edition.
ASTM A 715-81 Standard Specification for Steel 178.338
Sheet and Strip, Hot-Rolled, High-Strength, Low-
Alloy with Improved Formability, 1981.
ASTM B 162-93a Standard Specification for Nickel 179.200-7.
Plate, Sheet, and Strip.
ASTM B 209-93 Standard Specification for 179.100-7; 179.200-7;
Aluminum and Aluminum-Alloy Sheet and Plate. 179.220-7.
ASTM B 557-84 Tension Testing Wrought and Cast 178.46.
Aluminum and Magnesium-Alloy Products.
ASTM B 580-79 Standard Specification for Anodie 173.316; 173.318
Oxide Coatings on Aluminum, 1979.
ASTM D 56-97a Standard Test Method for Flash 173.120
Point by Tag Closed Tester.
ASTM D 93-97 Standard Test Methods for Flash 173.120
Point by Pensky-Martens Closed Cup Tester.
ASTM D 445-88 Kinematic Viscosity of 171.8
Transparent and Opaque Liquids (and the
Calculation of Dynamic Viscosity).
ASTM D 1200-88 Viscosity by Ford Viscosity Cup. 171.8
ASTM D 1838-64 Copper Strip Corrosion by 173.315
Liquefied Petroleum (LP) Gases.
ASTM D 3278-96 Standard Test Methods for Flash 173.120
Point of Liquids by Small Scale Closed-Cup
Apparatus.
ASTM D 3828-97, Standard Test Methods for Flash 173.120.
Point by Small Scale Closed Tester.
ASTM D 4206-96 Standard Test Method for 173.120.
Sustained Burning of Liquid Mixtures Using the
Small Scale Open-Cup Apparatus.
ASTM D 4359-90 Standard Test Method for 171.8
Determining Whether a Material is a Liquid or a
Solid.
ASTM E 8-89 Tension Testing of Metallic 178.36; 178.37;
Materials. 178.38; 178.39;
178.44; 178.45;
178.50; 178.51;
178.53; 178.55;
178.56; 178.57;
178.58; 178.59;
178.60; 178.61;
178.68.
ASTM E 23-60 Notched Bar Impact Testing of 178.57; 179.400
Metallic Materials.
ASTM E 112-88 Standard Test Methods for 178.44.
Determining Average Grain Size.
ASTM E 290-92 Standard Test Method for Semi- 178.46.
Guided Bend Test for Ductility of Metallic
Materials.
ASTM E 681-85 Standard Test Method for 173.115
Concentration Limits of Flammability of
Chemicals.
ASTM G 23-69 Standard Recommended Practice for 172.407; 172.519
Operating Light-and-Water Exposure Apparatus
(Carbon-Arc Type) for Exposure of Nonmetallic
Materials.
ASTM G 26-70 Standard Recommended Practice for 172.407; 172.519
Operating Light-and-Water Exposure Apparatus
(Xenon-Arc-Type) for Exposure of Nonmetallic
Materials.
ASTM G 31-72 (Reapproved 1995) Standard Practice 173.137
for Laboratory Immersion Corrosion Testing of
Metals.
American Water Works Association,
1010 Vermont Avenue, NW., Suite 810,
Washington, DC 20005
AWWA Standard C207-55, Steel Pipe Flanges, 1955. 178.360
American Welding Society,
550 N. W. Le Jeune Road, Miami, Florida 33126
AWS Code B 3.0; Standard Qualification 178.356
Procedure; 1972 (FRB 3.0-41, rev. May 1973).
AWS Code D 1.0; Code for Welding in Building 178.356
Construction (FR D 1.0-66).
Association of American Railroads,
American Railroads Building, 50 F Street, NW.,
Washington, DC 20001
AAR Manual of Standards and Recommended 173.31.
Practices, Section C--Part III, Specifications
for Tank Cars, Specification M-1002, September
1992.
[[Page 72]]
AAR Manual of Standards and Recommended 174.63; 179.6; 179.7;
Practices, Section C--Part III, Specifications 179.12; 179.15;
for Tank Cars, Specification M-1002, January 179.16; 179.20;
1996. 179.22; 179.100;
179.101; 179.102;
179.103; 179.200;
179.201; 179.220;
179.300; 179.400;
180.509; 180.513;
180.515; 180.517.
AAR Manual of Standards and Recommended 174.55; 174.63.
Practices, Section I, Specially Equipped
Freight Car and Intermodal Equipment, 1988.
AAR Specifications for Design, Fabrication and 179.16.
Construction of Freight Cars, Volume 1, 1988.
Chlorine Institute, Inc.,
2001 L Street, NW., Suite 506, Washington, DC
20036
Type 1\1/2\ JQ 225, Dwg, H51970, Revision D, 173.315
April 5, 1989; or Type 1\1/2\ JQ 225, Dwg.
H50155, Revision F, April 4, 1989.
Section 3, Pamphlet 57, Emergency Shut-Off 177.840
Systems for Bulk Transfer of Chlorine, 3rd
Edition, October 1997.
Standard Chlorine Angle Valve Assembly, Dwg. 104- 178.337-9
8, July 1993.
Excess Flow Valve with Removable Seat, Dwg. 101- 178.337-8
7, July 1993.
Excess Flow Valve with Removable Basket, Dwg. 178.337-8
106-6, July 1993.
Standards for Housing and Manway Covers for 178.337-10
Steel Cargo Tanks, Dwg. 137-3, September 1,
1982.
Compressed Gas Association, Inc.,
1725 Jefferson Davis Highway, Arlington,
Virginia 22202
CGA Pamphlet C-3, Standards for Welding and 178.47; 178.50;
Brazing on Thinned Walled Containers, 1975. 178.51; 178.53;
178.56; 178.57;
178.58; 178.59;
178.60; 178.61;
178.65; 178.68.
CGA Pamphlet C-5, Cylinder Service Life-- 173.302
Seamless Steel High Pressure Cylinders, 1991.
CGA Pamphlet C-6, Standards for Visual 173.34; 180.519
Inspection of Steel Compressed Gas Cylinders,
1993.
CGA Pamphlet C-6.1, Standards for Visual 173.34
Inspection of High Pressure Aluminum Compressed
Gas Cylinders, 1995.
CGA Pamphlet C-6.2, Guidelines for Visual 173.34
Inspection and Requalification of Fiber
Reinforced High Pressure Cylinders, 1988.
CGA Pamphlet C-6.3, Guidelines for Visual 173.34
Inspection and Requalification of Low Pressure
Aluminum Compressed Gas Cylinders, 1991.
CGA Pamphlet C-7, A Guide for the Preparation of 172.400a
Precautionary Markings for Compressed Gas
Containers, appendix A, issued 1992 (6th
Edition).
CGA Pamphlet C-8, Standard for Requalification 173.34
of DOT-3HT Cylinder Design, 1985.
CGA Pamphlet C-11, Recommended Practices for 178.35.
Inspection of Compressed Gas Cylinders at Time
of Manufacture, 1993.
CGA Pamphlet C-12, Qualification Procedure for 173.34; 173.303;
Acetylene Cylinder Design, 1994. 178.59; 178.60.
CGA Pamphlet C-13, Guidelines for Periodic 173.34; 173.303
Visual Inspection and Requalification of
Acetylene Cylinders, 1992.
CGA Pamphlet C-14, Procedures for Fire Testing 173.34
of DOT Cylinder Pressure Relief Device Systems,
1979.
CGA Pamphlet G-2.2 Tentative Standard Method for 173.315
Determining Minimum of 0.2% Water in Anhydrous
Ammonia, 1985.
CGA Pamphlet G-4.1, Cleaning Equipment for 178.338
Oxygen Service, 1985.
CGA Pamphlet S-1.1., Pressure Relief Device 173.34
Standards--Part 1--Cylinders for Compressed
Gases, 1994 (with the exception of paragraph
9.1.1.1).
CGA Pamphlet S-1.2, Safety Relief Device 173.315; 173.318
Standards Part 2--Cargo and Portable Tanks for
Compressed Gases, 1980.
CGA Technical Bulletin TB-2, Guidelines for 180.413
Inspection and Repair of MC-330 and MC-331
Cargo Tanks, 1980.
Department of Defense (DOD),
2461 Eisenhower Avenue, Alexandria, VA 22331
DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1-47; 173.56
DLAR 8220.1: Explosives Hazard Classification
Procedures, January 1998.
Department of Energy (USDOE),
100 Independence Avenue SW., Washington, DC
20545
USDOE publications available from:
Superintendent of Documents, Government
Printing Office (GPO) or The National
Technical Information Service (NTIS).
USDOE, CAPE-1662, Revision 1, and Supplement 1, 178.356; 178.358
Civilian Application Program Engineering
Drawings.
USDOE, Material and Equipment Specification No. 178.356; 178.358
SP-9, Rev. 1, and Supplement--Fire Resistant
Phenolic Foam.
USDOE, ORO 651--Uranium Hexafloride; A Manual of 173.417
Good Practices, Revision 6, 1991 edition.
USDOE, KSS-471, November 30, 1986--Proposal for 178.358
Modifications to U.S. Department of
Transportation Specification 21PF-1, Fire and
Shock Resistant Phenolic Foam--Insulated Metal
Overpack.
[[Page 73]]
General Services Administration,
Specification Office, Rm. 6662, 7th and D
Street, SW., Washington, DC 20407
Federal Specification RR-C-901C, Cylinders, 173.302; 173.304;
Compressed Gas: High Pressure Steel DOT 3AA, 173.336
and Aluminum Applications, January 15, 1981
(Superseding RR-C-901B, August 1, 1967).
Health and Human Services
Centers for Disease Control and Prevention,
1600 Clifton Road N.E., Atlanta GA 30333
Also available from: Superintendent of 173.134
Documents, Government Printing Office (GPO),
HHS Publication No. (CDC) 93-8395, Biosafety
in Microbiological and Biomedical
Laboratories, 3rd Edition, May 1993, Section
II
Institute of Makers of Explosives,
1120 19th Street, Suite 310, Washington, DC
20036-3605
IME Safety Library Publication No. 22 (IME 173.63, 177.835
Standard 22), Recommendation for the Safe
Transportation of Detonators in a Vehicle with
Certain Other Explosive Materials, May 1993.
International Atomic Energy Agency (IAEA),
IAEA, Regulations for the Safe Transport of 171.12
Radioactive Material, No. TS-R-1, 1996 Edition.
Wagramerstrasse 5, P.O. Box 100, A-1400,
Vienna, Austria
Also available from: Unipub Incorporated, P.O.
Box 433, New York, NY 10016
IAEA, Regulations for the Safe Transport of 171.12
Radioactive Materials, Safety Series No. 6,
1985 Edition (As Amended 1990); Including 1985
Edition (Supplemented 1986 and 1988).
International Civil Aviation Organization
(ICAO),
P.O. Box 400, Place de l'Aviation
Internationale, 1000 Sherbrooke Street West,
Montreal, Quebec, Canada H3A 2R2
ICAO Technical Instructions available from:
INTEREG, International Regulations,
Publishing and Distribution Organization,
P.O. Box 60105, Chicago, IL 60660
Technical Instructions for the Safe Transport of 171.11; 172.202;
Dangerous Goods by Air (ICAO Technical 172.401; 172.512;
Instructions), DOC 9284-AN/905, 2001-2002 172.602
Edition.
International Maritime Organization (IMO),
4 Albert Embankment, London, SE17SR, United
Kingdom
or New York Nautical Instrument & Service
Corporation, 140 W. Broadway, New York, NY
10013
International Maritime Dangerous Goods (IMDG) 171.12; 172;401;
Code, 1994 Consolidated Edition, as amended by 172.407; 173.21,
Amendment 29 (1998) (English edition). 176.2; 176.5; 176.11;
176.27; 176.30;
176.720
International Maritime Dangerous Goods (IMDG) 171.12; 172.401;
Code, 2000 edition, including Amendment 30-00 172.502; 173.21;
(English edition). 176.2; 176.5; 176.11;
176.27; 176.30.
International Organization for Standardization,
Case Postale 56, CH-1211, Geneve 20,
Switzerland
Also available from: ANSI, 1430 Broadway, New
York, NY 10018
ISO-82-1974(E) Steels Tensile Testing.......... 178.270-3
ISO 535-1991(E) Paper and board--Determination 178.516
of water absorptiveness--Cobb method.
ISO 1496-3 Series 1 freight containers-- 178.274
Specification and testing, Part 3: Tank
containers for liquids, gases and pressurized
dry bulk, March 1, 1995, Fourth Edition.
ISO 1496-3-1995(E) - Series 1 Freight 173.411
Containers--Specification and Testing--Part 3:
Tank Containers for Liquids, Gases and
Pressurized Dry Bulk.
ISO-2431-1984(E) Standard Cup Method........... 173.121
ISO 2592-1973(E) Petroleum products-- 173.120
Determination of flash and fire points--
Cleveland open cup method.
ISO 2919-1980(E) - Sealed radioactive sources-- 173.469
Classification.
ISO 3036-1975(E) Board--Determination of 178.708
puncture resistance.
ISO 3574-1986(E) Cold-reduced carbon steel sheet 178.503
of commercial and drawing qualities.
ISO 4126-1 Safety valves--Part 1:
General Requirements, December 15, 1991, 178.274
First Edition.
ISO/TR 4826-1979(E) - Sealed radioactive 173.469
sources--Leak test methods.
ISO 6892 Metallic materials--Tensile testing, 178.274
July 15, 1984, First Edition.
ISO 8115 Cotton bales--Dimensions and density, 172.102
1986 Edition.
ISO 9328-1--1991(E) Steel plates and strips for 173.137
pressure purposes--Technical delivery
conditions--Part 1: General requirements.
National Board of Boiler and Pressure Vessel
Inspectors,
1055 Crupper Avenue, Columbus, Ohio 43229
National Board Inspection Code, A Manual for 180.413
Boiler and Pressure Vessel Inspectors, NB-23,
1992 Edition.
National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269
NFPA Pamphlet No. 58--Standard for the Storage 173.315
and Handling of Liquefied Petroleum Gases, 1979.
National Institute of Standards and Technology,
Department of Commerce, 5285 Port Royal Road,
Springfield, VA 22151
USDC, NBS Handbook H-28 (1957), 1957 Handbook of 178.45, 178.46
Screw-Thread Standards for Federal Services,
Part II, December 1966 Edition.
[[Page 74]]
National Motor Freight Traffic Association,
Inc.,
Agent 1616 P Street, NW., Washington, DC 20036
National Motor Freight Classification NMF 100-I, 177.841
1982.
Organization for Economic Cooperation and
Development (OECD)
OECD Publications and Information Center, 2001
L Street, Suite 700, Washington, DC 20036
OECD Guideline for Testing of Chemicals, No.404 173.137
``Acute Dermal Irritation/Corrosion'', 1992.
Transport Canada,
TDG Canadian Government Publishing Center,
Supply and Services, Canada, Ottawa, Ontario,
Canada K1A 059.
Transportation of Dangerous Goods Regulations, 1 171.12a; 172.401;
July 1985, SOR/85/77, incorporating the 172.502.
following Registration Numbers: SOR/85-314, SOR/
85-585, SOR/85-609, SOR/86-526, SOR/88-635, SOR/
87-335, SOR/87-186, SOR/89-39, SOR/89-294, SOR/
90-847, SOR/91-711, SOR/91-712, SOR/92-447, SOR/
92-600, SOR/93-203, SOR/93-274, SOR/93-525, SOR/
94-146 and SOR/94-264 (English edition), SOR/95-
241, and SOR95-547.
Truck Trailer Manufacturers Association,
1020 Princess Street, Alexandria, Virginia
22314
TTMA RP No. 81, Performance of Spring Loaded 178.345-10
Pressure Relief Valves on MC 306, MC 307, and
MC 312 Tanks, May 24, 1989 Edition.
TTMA RP No. 61-94, Performance of Manhole and/or 180.405
Fill Opening Assemblies on MC 306 and DOT 406
Cargo Tanks, December 28, 1994 Edition..
TTMA TB No. 107, Procedure for Testing 180.405
Inservice, Unmarked, and/or Uncertified MC 306
Type Cargo Tank Manhole Covers, May 24, 1989
Edition.
United Nations,
United Nations Sales Section, New York, NY
10017
UN Recommendations on the Transport of Dangerous 172.401; 172.407;
Goods, Eleventh Revised Edition (1999). 172.502; 173.24.
UN Recommendations on the Transport of Dangerous 172.102; 173.21;
Goods, Manual of Tests and Criteria, Third 173.56; 173.57;
Revised Edition (1999). 173.124; 173.128;
173.166; 173.185.
------------------------------------------------------------------------
(b) List of informational materials not requiring incorporation by
reference. The materials listed in this paragraph do not require
approval for incorporation by reference and are included for
informational purposes. These materials may be used as noted in those
sections in which the material is referenced.
------------------------------------------------------------------------
Source and name of material 49 CFR reference
------------------------------------------------------------------------
Association of American Railroads,
American Railroads Building, 50 F Street, NW.,
Washington, DC 20001
AAR Catalog Nos. SE60CHT; SE60CC; SE60CHTE; 179.14
SE60CE; SE60DC; SE60DE.
AAR Catalog Nos. SE67CC; SE67CE; SE67BHT; 179.14
SE67BC; SE67BHTE; SE67BE.
AAR Catalog Nos. SE68BHT; SE68BC; SE68BHTE; 179.14
SE68BE.
AAR Catalog Nos. SE69AHTE; SE69AE............... 179.14
AAR Catalog Nos. SF70CHT; SF70CC; SF70CHTE; 179.14
SF70CE.
AAR Catalog Nos. SF73AC; SF73AE; SF73AHT; 179.14
SF73AHTE.
AAR Catalog Nos. SF79CHT; SF79CC; SF79CHTE; 179.14
SF79CE.
Bureau of Explosives,
Hazardous Materials Systems (BOE), Association
of American Railroads, American Railroads
Building, 50 F Street, NW., Washington, DC
20001
Fetterley's Formula (The Determination of the 173.315
Relief Dimensions for Safety Valves on
Containers in which Liquefied gas is charged
and when the exterior surface of the container
is exposed to a temperature of 1,200 deg.F.).
Pamphlet 6, Illustrating Methods for Loading and 174.55; 174.101;
Bracing Carload and Less-Than-Carload Shipments 174.112; 174.115;
of Explosives and Other Dangerous Articles, 174.290
1962.
Pamphlet 6A (includes appendix No. 1, October 174.101; 174.290
1944 and appendix 2, December 1945),
Illustrating Methods for Loading and Bracing
Carload and Less-Than-Carload Shipments of
Loaded Projectiles, Loaded Bombs, etc., 1943.
Pamphlet 6C, Illustrating Methods for Loading 174.55; 174.63;
and Bracing Trailers and Less-Than-Trailer 174.101; 174.112;
Shipments of Explosives and Other Dangerous 174.115
Articles Via Trailer-on-Flatcar (TOFC) or
Container-on-Flatcar (COFC), 1985.
Emergency Handling of Hazardous Materials in 171.7
Surface Transportation, 1989.
National Association of Corrosion Engineers,
1440 South Creek, Houston, Texas 77084
NACE Standard TM-01-69, Test Method Laboratory 173.136
Corrosion Testing of Metals for the Process
Industries, 1969.
Society of Plastics Industries, Inc.,
Organic Peroxide Producers Safety Division,
1275 K Street, NW., Suite 400, Washington, DC
20005
Self Accelerating Decomposition Temperature 173.21
Test, 1972.
------------------------------------------------------------------------
[[Page 75]]
[Amdt. 171-111, 55 FR 52466, Dec. 21, 1990, as amended by 66 FR 33334,
June 21, 2001; 66 FR 45378, Aug. 28, 2001]
Editorial Note: For Federal Register citations affecting Sec. 171.7,
see the List of CFR Sections Affected which appears in the Finding Aids
section of the printed volume and on GPO Access.
Sec. 171.8 Definitions and abbreviations.
In this subchapter,
Aerosol means any non-refillable receptacle containing a gas
compressed, liquefied or dissolved under pressure, the sole purpose of
which is to expel a nonpoisonous (other than a Division 6.1 Packing
Group III material) liquid, paste, or powder and fitted with a self-
closing release device allowing the contents to be ejected by the gas.
Agricultural product means a hazardous material, other than a
hazardous waste, whose end use directly supports the production of an
agricultural commodity including, but not limited to a fertilizer,
pesticide, soil amendment or fuel. An agricultural product is limited to
a material in Class 3, 8 or 9, Division 2.1, 2.2, 5.1, or 6.1, or an
ORM-D material.
Approval means a written authorization, including a competent
authority approval, from the Associate Administrator to perform a
function for which prior authorization by the Associate Administrator is
required under subchapter C of this chapter.
Approved means approval issued or recognized by the Department
unless otherwise specifically indicated in this subchapter.
Asphyxiant gas means a gas which dilutes or replaces oxygen normally
in the atmosphere.
Associate Administrator means the Associate Administrator for
Hazardous Materials Safety, Research and Special Programs
Administration.
Atmospheric gases means air, nitrogen, oxygen, argon, krypton, neon
and xenon.
Authorized Inspection Agency means: (1) A jurisdiction which has
adopted and administers one or more sections of the ASME Boiler and
Pressure Vessel Code as a legal requirement and has a representative
serving as a member of the ASME Conference Committee; or (2) an
insurance company which has been licensed or registered by the
appropriate authority of a State of the United States or a Province of
Canada to underwrite boiler and pressure vessel insurance in such State
or Province.
Authorized Inspector means an Inspector who is currently
commissioned by the National Board of Boiler and Pressure Vessel
Inspectors and employed as an Inspector by an Authorized Inspection
Agency.
Bag means a flexible packaging made of paper, plastic film,
textiles, woven material or other similar materials.
Bar means 1 BAR = 100 kPa (14.5 psi).
Barge means a non-selfpropelled vessel.
Bottle means an inner packaging having a neck of relatively smaller
cross section than the body and an opening capable of holding a closure
for retention of the contents.
Bottom shell means that portion of a tank car tank surface,
excluding the head ends of the tank car tank, that lies within two feet,
measured circumferentially, of the bottom longitudinal center line of
the tank car tank.
Box means a packaging with complete rectangular or polygonal faces,
made of metal, wood, plywood, reconstituted wood, fiberboard, plastic,
or other suitable material. Holes appropriate to the size and use of the
packaging, for purposes such as ease of handling or opening, or to meet
classification requirements, are permitted as long as they do not
compromise the integrity of the packaging during transportation, and are
not otherwise prohibited in this subchapter.
Break-bulk means packages of hazardous materials that are handled
individually, palletized, or unitized for purposes of transportation as
opposed to bulk and containerized freight.
Btu means British thermal unit.
Bulk packaging means a packaging, other than a vessel or a barge,
including a transport vehicle or freight container, in which hazardous
materials are loaded with no intermediate form of containment and which
has:
(1) A maximum capacity greater than 450 L (119 gallons) as a
receptacle for a liquid;
[[Page 76]]
(2) A maximum net mass greater than 400 kg (882 pounds) and a
maximum capacity greater than 450 L (119 gallons) as a receptacle for a
solid; or
(3) A water capacity greater than 454 kg (1000 pounds) as a
receptacle for a gas as defined in Sec. 173.115 of this subchapter.
Bureau of Explosives means the Bureau of Explosives (B of E) of the
Association of American Railroads.
C means Celsius or Centigrade.
Captain of the Port (COTP) means the officer of the Coast Guard,
under the command of a District Commander, so designated by the
Commandant for the purpose of giving immediate direction to Coast Guard
law enforcement activities within an assigned area. As used in this
subchapter, the term Captain of the Port includes an authorized
representative of the Captain of the Port.
Carfloat means a vessel that operates on a short run on an irregular
basis and serves one or more points in a port area as an extension of a
rail line or highway over water, and does not operate in ocean,
coastwise, or ferry service.
Cargo aircraft only means an aircraft that is used to transport
cargo and is not engaged in carrying passengers. For purposes of this
subchapter, the terms cargo aircraft only, cargo-only aircraft and cargo
aircraft have the same meaning.
Cargo tank means a bulk packaging which:
(1) Is a tank intended primarily for the carriage of liquids or
gases and includes appurtenances, reinforcements, fittings, and closures
(for tank, see 49 CFR 178.345-1(c), 178.337-1, or 178.338-1, as
applicable);
(2) Is permanently attached to or forms a part of a motor vehicle,
or is not permanently attached to a motor vehicle but which, by reason
of its size, construction or attachment to a motor vehicle is loaded or
unloaded without being removed from the motor vehicle; and
(3) Is not fabricated under a specification for cylinders, portable
tanks, tank cars, or multi-unit tank car tanks.
Cargo tank motor vehicle means a motor vehicle with one or more
cargo tanks permanently attached to or forming an integral part of the
motor vehicle.
Cargo vessel means: (1) Any vessel other than a passenger vessel;
and
(2) Any ferry being operated under authority of a change of
character certificate issued by a Coast Guard Officer-in-Charge, Marine
Inspection.
Carrier means a person engaged in the transportation of passengers
or property by:
(1) Land or water, as a common, contract, or private carrier, or
(2) Civil aircraft.
CC means closed-cup.
Character of vessel means the type of service in which the vessel is
engaged at the time of carriage of a hazardous material.
Class means hazard class. See hazard class.
Class 1. See Sec. 173.50 of this subchapter.
Class 2. See Sec. 173.115 of this subchapter.
Class 3. See Sec. 173.120 of this subchapter.
Class 4. See Sec. 173.124 of this subchapter.
Class 5. See Sec. 173.128 of this subchapter.
Class 6. See Sec. 173.132 of this subchapter.
Class 7. See Sec. 173.403 of this subchapter.
Class 8. See Sec. 173.136 of this subchapter.
Class 9. See Sec. 173.140 of this subchapter.
Closure means a device which closes an opening in a receptacle.
COFC means container-on-flat-car.
Combination packaging means a combination of packaging, for
transport purposes, consisting of one or more inner packagings secured
in a non-bulk outer packaging. It does not include a composite
packaging.
Combustible liquid. See Sec. 173.120 of this subchapter.
Compatibility group letter means a designated alphabetical letter
used to categorize different types of explosive substances and articles
for purposes of stowage and segregation. See Sec. 173.52 of this
subchapter.
Competent Authority means a national agency responsible under its
national law for the control or regulation of a particular aspect of the
transportation
[[Page 77]]
of hazardous materials (dangerous goods). The term Appropriate
Authority, as used in the ICAO Technical Instructions (see Sec. 171.7),
has the same meaning as Competent Authority. For purposes of this
subchapter, the Associate Administrator is the Competent Authority for
the United States.
Composite packaging means a packaging consisting of an outer
packaging and an inner receptacle, so constructed that the inner
receptacle and the outer packaging form an integral packaging. Once
assembled it remains thereafter an integrated single unit; it is filled,
stored, shipped and emptied as such.
Compressed gas. See Sec. 173.115 of this subchapter.
Consumer commodity means a material that is packaged and distributed
in a form intended or suitable for sale through retail sales agencies or
instrumentalities for consumption by individuals for purposes of
personal care or household use. This term also includes drugs and
medicines.
Containership means a cargo vessel designed and constructed to
transport, within specifically designed cells, portable tanks and
freight containers which are lifted on and off with their contents
intact.
Corrosive material. See Sec. 173.136 of this subchapter.
Crate means an outer packaging with incomplete surfaces.
Crewmember means a person assigned to perform duty in an aircraft
during flight time.
Cryogenic liquid. See Sec. 173.115(g) of this subchapter.
Cylinder means a pressure vessel designed for pressures higher than
40 psia and having a circular cross section. It does not include a
portable tank, multi-unit tank car tank, cargo tank, or tank car.
Dangerous when wet material. See Sec. 173.124 of this subchapter.
Design Certifying Engineer means a person registered with the
Department in accordance with subpart F of part 107 of this chapter who
has the knowledge and ability to perform stress analysis of pressure
vessels and to otherwise determine whether a cargo tank design and
construction meets the applicable DOT specification. In addition, Design
Certifying Engineer means a person who meets, at a minimum, any one of
the following:
(1) Has an engineering degree and one year of work experience in
cargo tank structural or mechanical design.
(2) Is currently registered as a professional engineer by the
appropriate authority of a State of the United States or a Province of
Canada.
(3) Has at least three years experience in performing the duties of
a Design Certifying Engineer by September 1, 1991, and was registered
with the Department by December 31, 1995.
Designated facility means a hazardous waste treatment, storage, or
disposal facility that has been designated on the manifest by the
generator.
District Commander means the District Commander of the Coast Guard,
or his authorized representative, who has jurisdiction in the particular
geographical area.
Division means a subdivision of a hazard class.
DOD means the U.S. Department of Defense.
Domestic transportation means transportation between places within
the United States other than through a foreign country.
DOT or Department means U.S. Department of Transportation.
Drum means a flat-ended or convex-ended cylindrical packaging made
of metal, fiberboard, plastic, plywood, or other suitable materials.
This definition also includes packagings of other shapes made of metal
or plastic (e.g., round taper-necked packagings or pail-shaped
packagings) but does not include cylinders, jerricans, wooden barrels or
bulk packagings.
Elevated temperature material means a material which, when offered
for transportation or transported in a bulk packaging:
(1) Is in a liquid phase and at a temperature at or above 100 deg.C
(212 deg.F);
(2) Is in a liquid phase with a flash point at or above 37.8 deg.C
(100 deg.F) that is intentionally heated and offered for transportation
or transported at or above its flash point; or
(3) Is in a solid phase and at a temperature at or above 240 deg.C
(464 deg.F).
Engine means a locomotive propelled by any form of energy and used
by a railroad.
[[Page 78]]
EPA means U.S. Environmental Protection Agency.
Etiologic agent. See Sec. 173.134 of this subchapter.
EX number means a number preceded by the prefix ``EX'', assigned by
the Associate Administrator, to an item that has been evaluated under
the provisions of Sec. 173.56 of this subchapter.
Exemption means a document issued under the authority of 49 U.S.C.
5117 by the Associate Administrator that authorizes a person to perform
a function that is not otherwise authorized under this subchapter,
subchapter C, or other regulations issued under 49 U.S.C. 5101-5127
(e.g., Federal Motor Carrier Safety Administration routing).
Explosive. See Sec. 173.50 of this subchapter.
F means degree Fahrenheit.
Farmer means a person engaged in the production or raising of crops,
poultry, or livestock.
Federal hazardous material transportation law means 49 U.S.C. 5101
et seq.
Ferry vessel means a vessel which is limited in its use to the
carriage of deck passengers or vehicles or both, operates on a short run
on a frequent schedule between two points over the most direct water
route, other than in ocean or coastwise service, and is offered as a
public service of a type normally attributed to a bridge or tunnel.
Filling density has the following meanings:
(1) For compressed gases in cylinders, see Sec. 173.304(a)(2) table
note 1.
(2) For compressed gases in tank cars, see Sec. 173.314(c) table
note 1.
(3) For compressed gases in cargo tanks and portable tanks, see
Sec. 173.315(a) table note 1.
(4) For cryogenic liquids in cylinders, except hydrogen, see
Sec. 173.316(c)(1).
(5) For hydrogen, cryogenic liquid in cylinders, see
Sec. 173.316(c)(3) table note 1.
(6) For cryogenic liquids in cargo tanks, see Sec. 173.318(f)(1).
(7) For cryogenic liquids in tank cars, see Sec. 173.319(d)(1).
Flammable gas. See Sec. 173.115 of this subchapter.
Flammable liquid. See Sec. 173.120 of this subchapter.
Flammable solid. See Sec. 173.124 of this subchapter.
Flash point. See Sec. 173.120 of this subchapter.
Freight container means a reusable container having a volume of 64
cubic feet or more, designed and constructed to permit being lifted with
its contents intact and intended primarily for containment of packages
(in unit form) during transportation.
Fuel tank means a tank other than a cargo tank, used to transport
flammable or combustible liquid, or compressed gas for the purpose of
supplying fuel for propulsion of the transport vehicle to which it is
attached, or for the operation of other equipment on the transport
vehicle.
Fumigated lading. See Secs. 172.302(g) and 173.9.
Gas means a material which has a vapor pressure greater than 300 kPa
(43.5 psia) at 50 deg.C (122 deg.F) or is completely gaseous at 20
deg.C (68 deg.F) at a standard pressure of 101.3 kPa (14.7 psia).
Gross weight or Gross mass means the weight of a packaging plus the
weight of its contents.
Hazard class means the category of hazard assigned to a hazardous
material under the definitional criteria of part 173 of this subchapter
and the provisions of the Sec. 172.101 table. A material may meet the
defining criteria for more than one hazard class but is assigned to only
one hazard class.
Hazard zone means one of four levels of hazard (Hazard Zones A
through D) assigned to gases, as specified in Sec. 173.116(a) of this
subchapter, and one of two levels of hazards (Hazard Zones A and B)
assigned to liquids that are poisonous by inhalation, as specified in
Sec. 173.133(a) of this subchapter. A hazard zone is based on the LC50
value for acute inhalation toxicity of gases and vapors, as specified in
Sec. 173.133(a).
Hazardous material means a substance or material, which has been
determined by the Secretary of Transportation to be capable of posing an
unreasonable risk to health, safety, and property when transported in
commerce, and which has been so designated. The term includes hazardous
substances, hazardous wastes, marine pollutants, and
[[Page 79]]
elevated temperature materials as defined in this section, materials
designated as hazardous under the provisions of Sec. 172.101 of this
subchapter, and materials that meet the defining criteria for hazard
classes and divisions in part 173 of this subchapter.
Hazardous substance for the purposes of this subchapter, means a
material, including its mixtures and solutions, that--
(1) Is listed in the appendix A to Sec. 172.101 of this subchapter;
(2) Is in a quantity, in one package, which equals or exceeds the
reportable quantity (RQ) listed in the appendix A to Sec. 172.101 of
this subchapter; and
(3) When in a mixture or solution--
(i) For radionuclides, conforms to paragraph 7 of the appendix A to
Sec. 172.101.
(ii) For other than radionuclides, is in a concentration by weight
which equals or exceeds the concentration corresponding to the RQ of the
material, as shown in the following table:
------------------------------------------------------------------------
Concentration by
weight
RQ pounds (kilograms) ---------------------
Percent PPM
------------------------------------------------------------------------
5000 (2270)....................................... 10 100,000
1000 (454)........................................ 2 20,000
100 (45.4)........................................ 0.2 2,000
10 (4.54)......................................... 0.02 200
1 (0.454)......................................... 0.002 20
------------------------------------------------------------------------
The term does not include petroleum, including crude oil or any
fraction thereof which is not otherwise specifically listed or
designated as a hazardous substance in appendix A to Sec. 172.101 of
this subchapter, and the term does not include natural gas, natural gas
liquids, liquefied natural gas, or synthetic gas usable for fuel (or
mixtures of natural gas and such synthetic gas).
Hazardous waste, for the purposes of this chapter, means any
material that is subject to the Hazardous Waste Manifest Requirements of
the U.S. Environmental Protection Agency specified in 40 CFR part 262.
Hazmat employee means a person who is employed by a hazmat employer
and who in the course of employment directly affects hazardous materials
transportation safety. This term includes an owner-operator of a motor
vehicle which transports hazardous materials in commerce. This term
includes an individual, including a self-employed individual, employed
by a hazmat employer who, during the course of employment:
(1) Loads, unloads, or handles hazardous materials;
(2) Manufactures, tests, reconditions, repairs, modifies, marks, or
otherwise represents containers, drums, or packagings as qualified for
use in the transportation of hazardous materials;
(3) Prepares hazardous materials for transportation;
(4) Is responsible for safety of transporting hazardous materials;
or
(5) Operates a vehicle used to transport hazardous materials.
Hazmat employer means a person who uses one or more of its employees
in connection with: transporting hazardous materials in commerce;
causing hazardous materials to be transported or shipped in commerce; or
representing, marking, certifying, selling, offering, manufacturing,
reconditioning, testing, repairing, or modifying containers, drums, or
packagings as qualified for use in the transportation of hazardous
materials. This term includes an owner-operator of a motor vehicle which
transports hazardous materials in commerce. This term also includes any
department, agency, or instrumentality of the United States, a State, a
political subdivision of a State, or an Indian tribe engaged in an
activity described in the first sentence of this definition.
Hermetically sealed means closed by fusion, gasketing, crimping, or
equivalent means so that no gas or vapor can enter or escape.
IAEA means International Atomic Energy Agency.
IATA means International Air Transport Association.
ICAO means International Civil Aviation Organization.
IMO means International Maritime Organization.
Infectious substance (etiologic agent). See Sec. 173.134 of this
subchapter.
Inner packaging means a packaging for which an outer packaging is
required for transport. It does not include the inner receptacle of a
composite packaging.
[[Page 80]]
Inner receptacle means a receptacle which requires an outer
packaging in order to perform its containment function. The inner
receptacle may be an inner packaging of a combination packaging or the
inner receptacle of a composite packaging.
Intermediate bulk container or IBC means a rigid or flexible
portable packaging, other than a cylinder or portable tank, which is
designed for mechanical handling. Standards for IBCs manufactured in the
United States are set forth in subparts N and O of part 178 of this
subchapter.
Intermediate packaging means a packaging which encloses an inner
packaging or article and is itself enclosed in an outer packaging.
Intermodal container means a freight container designed and
constructed to permit it to be used interchangeably in two or more modes
of transport.
Intermodal portable tank or IM portable tank means a specific class
of portable tanks designed primarily for international intermodal use.
International transportation means transportation--
(1) Between any place in the United States and any place in a
foreign country;
(2) Between places in the United States through a foreign country;
or
(3) Between places in one or more foreign countries through the
United States.
Irritating material. See Sec. 173.132(a)(2) of this subchapter.
Jerrican means a metal or plastic packaging of rectangular or
polygonal cross-section.
Large packaging means a packaging that--
(1) Consists of an outer packaging which contains articles or inner
packagings;
(2) Is designated for mechanical handling;
(3) Exceeds 400 kg net mass or 450 liters (118.9 gallons) capacity;
(4) Has a volume of not more than 3 m\3\ (see Sec. 178.801(i) of
this subchapter); and
(5) Conforms to the requirements for the construction, testing and
marking of large packagings as specified in the UN Recommendations.
Limited quantity, when specified as such in a section applicable to
a particular material, means the maximum amount of a hazardous material
for which there is a specific labeling or packaging exception.
Liquid means a material, other than an elevated temperature
material, with a melting point or initial melting point of 20 deg.C (68
deg.F) or lower at a standard pressure of 101.3 kPa (14.7 psia). A
viscous material for which a specific melting point cannot be determined
must be subjected to the procedures specified in ASTM D 4359 ``Standard
Test Method for Determining Whether a Material is Liquid or Solid'' (see
Sec. 171.7).
Liquid phase means a material that meets the definition of liquid
when evaluated at the higher of the temperature at which it is offered
for transportation or at which it is transported, not at the 37.8 deg.C
(100 deg.F) temperature specified in ASTM D 4359-84.
Magazine vessel means a vessel used for the receiving, storing, or
dispensing of explosives.
Magnetic material. See Sec. 173.21(d) of this subchapter.
Marine pollutant, means a material which is listed in appendix B to
Sec. 172.101 of this subchapter (also see Sec. 171.4) and, when in a
solution or mixture of one or more marine pollutants, is packaged in a
concentration which equals or exceeds:
(1) Ten percent by weight of the solution or mixture for materials
listed in the appendix; or
(2) One percent by weight of the solution or mixture for materials
that are identified as severe marine pollutants in the appendix.
Marking means a descriptive name, identification number,
instructions, cautions, weight, specification, or UN marks, or
combinations thereof, required by this subchapter on outer packagings of
hazardous materials.
Material of trade means a hazardous material, other than a hazardous
waste, that is carried on a motor vehicle--
(1) For the purpose of protecting the health and safety of the motor
vehicle operator or passengers;
(2) For the purpose of supporting the operation or maintenance of a
motor
[[Page 81]]
vehicle (including its auxiliary equipment); or
(3) By a private motor carrier (including vehicles operated by a
rail carrier) in direct support of a principal business that is other
than transportation by motor vehicle.
Material poisonous by inhalation means:
(1) A gas meeting the defining criteria in Sec. 173.115(c) of this
subchapter and assigned to Hazard Zone A, B, C, or D in accordance with
Sec. 173.116(a) of this subchapter;
(2) A liquid (other than as a mist) meeting the defining criteria in
Sec. 173.132(a)(1)(iii) of this subchapter and assigned to Hazard Zone A
or B in accordance with Sec. 173.133(a) of this subchapter; or
(3) Any material identified as an inhalation hazard by a special
provision in column 7 of the Sec. 172.101 table.
MAWP means maxumum allowable working pressure.
Maximum capacity means the maximum inner volume of receptacles or
packagings.
Maximum net mass means the allowable maximum net mass of contents in
a single packaging, or as used in subpart M of part 178 of this
subchapter, the maximum combined mass of inner packaging, and the
contents thereof.
Metered delivery service means a cargo tank unloading operation
conducted at a metered flow rate of 378.5 L (100 gallons) per minute or
less through an attached delivery hose with a nominal inside diameter of
3.175 cm (1\1/4\ inches) or less.
Miscellaneous hazardous material. See Sec. 173.140 of this
subchapter.
Mixture means a material composed of more than one chemical compound
or element.
Mode means any of the following transportation methods; rail,
highway, air, or water.
Motor vehicle includes a vehicle, machine, tractor, trailer, or
semitrailer, or any combination thereof, propelled or drawn by
mechanical power and used upon the highways in the transportation of
passengers or property. It does not include a vehicle, locomotive, or
car operated exclusively on a rail or rails, or a trolley bus operated
by electric power derived from a fixed overhead wire, furnishing local
passenger transportation similar to street-railway service.
Name of contents means the proper shipping name as specified in
Sec. 172.101 of this subchapter.
Navigable waters means, for the purposes of this subchapter, waters
of the United States, including the territorial seas.
Non-bulk packaging means a packaging which has:
(1) A maximum capacity of 450 L (119 gallons) or less as a
receptacle for a liquid;
(2) A maximum net mass of 400 kg (882 pounds) or less and a maximum
capacity of 450 L (119 gallons) or less as a receptacle for a solid; or
(3) A water capacity of 454 kg (1000 pounds) or less as a receptacle
for a gas as defined in Sec. 173.115 of this subchapter.
Nonflammable gas. See Sec. 173.115 of this subchapter.
N.O.S. means not otherwise specified.
N.O.S. description means a shipping description from the
Sec. 172.101 table which includes the abbreviation n.o.s.
NPT means an American Standard taper pipe thread conforming to
requirements of Federal Standard H28, part II, section VII. See
Sec. 171.7.
NRC (non-reusable container) means a packaging (container) whose
reuse is restricted in accordance with the provisions of Sec. 173.28 of
this subchapter.
Occupied caboose means a rail car being used to transport non-
passenger personnel.
Officer in Charge, Marine Inspection means a person from the
civilian or military branch of the Coast Guard designated as such by the
Commandant and who under the supervision and direction of the Coast
Guard District Commander is in charge of a designated inspection zone
for the performance of duties with respect to the enforcement and
administration of title 52, Revised Statutes, acts amendatory thereof or
supplemental thereto, rules and regulations thereunder, and the
inspection required thereby.
Offshore supply vessel means a cargo vessel of less than 500 gross
tons that regularly transports goods, supplies or equipment in support
of exploration or
[[Page 82]]
production of offshore mineral or energy resources.
Operator means a person who controls the use of an aircraft, vessel,
or vehicle.
Organic peroxide. See Sec. 173.128 of this subchapter.
ORM means other regulated material. See Sec. 173.144 of this
subchapter.
Outage or ullage means the amount by which a packaging falls short
of being liquid full, usually expressed in percent by volume.
Outer packaging means the outermost enclosure of a composite or
combination packaging together with any absorbent materials, cushioning
and any other components necessary to contain and protect inner
receptacles or inner packagings.
Overpack, except as provided in subpart K of part 178 of this
subchapter, means an enclosure that is used by a single consignor to
provide protection or convenience in handling of a package or to
consolidate two or more packages. Overpack does not include a transport
vehicle, freight container, or aircraft unit load device. Examples of
overpacks are one or more packages:
(1) Placed or stacked onto a load board such as a pallet and secured
by strapping, shrink wrapping, stretch wrapping, or other suitable
means; or
(2) Placed in a protective outer packaging such as a box or crate.
Oxidizer. See Sec. 173.127 of this subchapter.
Oxidizing gas means a gas which may, generally by providing oxygen,
cause or contribute to the combustion of other material more than air
does.
Oxygen generator (chemical) means a device containing chemicals that
upon activation release oxygen as a product of chemical reaction.
Package or Outside Package means a packaging plus its contents. For
radioactive materials, see Sec. 173.403 of this subchapter.
Packaging means a receptacle and any other components or materials
necessary for the receptacle to perform its containment function in
conformance with the minimum packing requirements of this subchapter.
For radioactive materials packaging, see Sec. 173.403 of this
subchapter.
Packing group means a grouping according to the degree of danger
presented by hazardous materials. Packing Group I indicates great
danger; Packing Group II, medium danger; Packing Group III, minor
danger. See Sec. 172.101(f) of this subchapter.
Passenger (With respect to vessels and for the purposes of part 176
only) means a person being carried on a vessel other than:
(1) The owner or his representative;
(2) The operator;
(3) A bona fide member of the crew engaged in the business of the
vessel who has contributed no consideration for his carriage and who is
paid for his services; or
(4) A guest who has not contributed any consideration directly or
indirectly for his carriage.
Passenger-carrying aircraft means an aircraft that carries any
person other than a crewmember, company employee, an authorized
representative of the United States, or a person accompanying the
shipment.
Passenger vessel means--
(1) A vessel subject to any of the requirements of the International
Convention for the Safety of Life at Sea, 1974, which carries more than
12 passengers;
(2) A cargo vessel documented under the laws of the United States
and not subject to that Convention, which carries more than 16
passengers;
(3) A cargo vessel of any foreign nation that extends reciprocal
privileges and is not subject to that Convention and which carries more
than 16 passengers; and
(4) A vessel engaged in a ferry operation and which carries
passengers.
Person means an individual, firm, copartnership, corporation,
company, association, joint-stock association, including any trustee,
receiver, assignee, or similar representative thereof; or government,
Indian tribe, or agency or instrumentality of any government or Indian
tribe when it offers hazardous material for transportation in commerce
or transports hazardous material to further a commercial enterprise, but
such term does not include:
(1) The United States Postal Service;
[[Page 83]]
(2) For the purposes of 49 U.S.C. 5123 and 5124, any agency or
instrumentality of the Federal Government.
Placarded car means a rail car which is placarded in accordance with
the requirements of part 172 of this subchapter.
Poisonous gas. See Sec. 173.115 of this subchapter.
Poisonous materials. See Sec. 173.132 of this subchapter.
Portable tank means a bulk packaging (except a cylinder having a
water capacity of 1000 pounds or less) designed primarily to be loaded
onto, or on, or temporarily attached to a transport vehicle or ship and
equipped with skids, mountings, or accessories to facilitate handling of
the tank by mechanical means. It does not include a cargo tank, tank
car, multi-unit tank car tank, or trailer carrying 3AX, 3AAX, or 3T
cylinders.
Preferred route or Preferred highway is a highway for shipment of
highway route controlled quantities of radioactive materials so
designated by a State routing agency, and any Interstate System highway
for which an alternative highway has not been designated by such State
agency as provided by Sec. 397.103 of this title.
Primary hazard means the hazard class of a material as assigned in
the Sec. 172.101 table.
Private track or Private siding means track located outside of a
carrier's right-of-way, yard, or terminals where the carrier does not
own the rails, ties, roadbed, or right-of-way and includes track or
portion of track which is devoted to the purpose of its user either by
lease or written agreement, in which case the lease or written agreement
is considered equivalent to ownership.
Proper shipping name means the name of the hazardous material shown
in Roman print (not italics) in Sec. 172.101 of this subchapter.
Psi means psig.
Psia means psig absolute.
Psig means psig gauge.
Public vessel means a vessel owned by and being used in the public
service of the United States. It does not include a vessel owned by the
United States and engaged in a trade or commercial service or a vessel
under contract or charter to the United States.
Pyrophoric liquid. See Sec. 173.124(b) of this subchapter.
Radioactive materials. See Sec. 173.403 of this subchapter for
definitions relating to radioactive materials.
Rail car means a car designed to carry freight or non-passenger
personnel by rail, and includes a box car, flat car, gondola car, hopper
car, tank car, and occupied caboose.
Railroad means a person engaged in transportation by rail.
Receptacle means a containment vessel for receiving and holding
materials, including any means of closing.
Registered Inspector means a person registered with the Department
in accordance with subpart F of part 107 of this chapter who has the
knowledge and ability to determine whether a cargo tank conforms with
the applicable DOT specification. In addition, Registered Inspector
means a person who meets, at a minimum, any one of the following:
(1) Has an engineering degree and one year of work experience.
(2) Has an associate degree in engineering and two years of work
experience.
(3) Has a high school diploma or General Equivalency Diploma) and
three years of work experience.
(4) Has at least three years experience in performing the duties of
a Registered Inspector by September 1, 1991, and was registered with the
Department by December 31, 1995.
Regulated medical waste. See Sec. 173.134 of this subchapter.
Reportable quantity (RQ) for the purposes of this subchapter means
the quantity specified in column 2 of the appendix to Sec. 172.101 for
any material identified in column 1 of the appendix.
Research means investigation or experimentation aimed at the
discovery of new theories or laws and the discovery and interpretation
of facts or revision of accepted theories or laws in the light of new
facts.
Residue means the hazardous material remaining in a packaging,
including a tank car, after its contents have been unloaded to the
maximum extent practicable and before the packaging is either refilled
or cleaned of hazardous
[[Page 84]]
material and purged to remove any hazardous vapors.
RSPA means the Research and Special Programs Administration, U.S.
Department of Transportation, Washington, DC 20590.
SADT means self-accelerated decomposition temperature. See
Sec. 173.21(f) of this subchapter.
Salvage packaging means a special packaging conforming to Sec. 173.3
of this subchapter into which damaged, defective or leaking hazardous
materials packages, or hazardous materials that have spilled or leaked,
are placed for purposes of transport for recovery or disposal.
SCF (standard cubic foot) means one cubic foot of gas measured at 60
deg.F. and 14.7 psia.
Self-defense spray means an aerosol or non-pressurized device that:
(1) Is intended to have an irritating or incapacitating effect on a
person or animal; and
(2) Meets no hazard criteria other than for Class 9 (for example, a
pepper spray; see Sec. 173.140(a) of this subchapter) and, for an
aerosol, Division 2.1 or 2.2 (see Sec. 173.115 of this subchapter),
except that it may contain not more than two percent by mass of a tear
gas substance (e.g., chloroacetophenone (CN) or 0-
chlorobenzylmalonitrile (CS); see Sec. 173.132(a)(2) of this
subchapter.)
Sheathing means a covering consisting of a smooth layer of wood
placed over metal and secured to prevent any movement.
Shipping paper means a shipping order, bill of lading, manifest or
other shipping document serving a similar purpose and containing the
information required by Secs. 172.202, 172.203 and 172.204.
Siftproof packaging means a packaging impermeable to dry contents,
including fine solid material produced during transportation.
Single packaging means a non-bulk packaging other than a combination
packaging.
Solid means a material which is not a gas or a liquid.
Solution means any homogeneous liquid mixture of two or more
chemical compounds or elements that will not undergo any segregation
under conditions normal to transportation.
Specification packaging means a packaging conforming to one of the
specifications or standards for packagings in part 178 or part 179 of
this subchapter.
Stabilized means that the hazardous material is in a condition that
precludes uncontrolled reaction. This may be achieved by methods such as
adding an inhibiting chemical, degassing the hazardous material to
remove dissolved oxygen and inerting the air space in the package, or
maintaining the hazardous material under temperature control.
Spontaneously combustible material. See Sec. 173.124(b) of this
subchapter.
State means a State of the United States, the District of Columbia,
the Commonwealth of Puerto Rico, the Commonwealth of the Northern
Mariana Islands, the Virgin Islands, American Samoa, Guam, or any other
territory or possession of the United States designated by the
Secretary.
State-designated route means a preferred route selected in
accordance with U.S. DOT ``Guidelines for Selecting Preferred Highway
Routes for Highway Route Controlled Quantities of Radioactive
Materials'' or an equivalent routing analysis which adequately considers
overall risk to the public.
Stowage means the act of placing hazardous materials on board a
vessel.
Strong outside container means the outermost enclosure which
provides protection against the unintentional release of its contents
under conditions normally incident to transportation.
Subsidiary hazard means a hazard of a material other than the
primary hazard. (See primary hazard).
Table in Sec. 172.101 or Sec. 172.101 table means the Hazardous
Materials Table in Sec. 172.101 of this subchapter.
Technical name means a recognized chemical name or microbiological
name currently used in scientific and technical handbooks, journals, and
texts. Generic descriptions are authorized for use as technical names
provided they readily identify the general chemical group, or
microbiological group. Examples of acceptable generic
[[Page 85]]
chemical descriptions are organic phosphate compounds, petroleum
aliphatic hydrocarbons and tertiary amines. For proficiency testing
only, generic microbiological descriptions such as bacteria,
mycobacteria, fungus, and viral samples may be used. Except for names
which appear in subpart B of part 172 of this subchapter, trade names
may not be used as technical names.
TOFC means trailer-on-flat-car.
Top shell means the tank car tank surface, excluding the head ends
and bottom shell of the tank car tank.
Trailership means a vessel, other than a carfloat, specifically
equipped to carry motor transport vehicles and fitted with installed
securing devices to tie down each vehicle. The term trailership includes
Roll-on/Roll-off (RO/RO) vessels.
Train means one or more engines coupled with one or more rail cars,
except during switching operations or where the operation is that of
classifying and assembling rail cars within a railroad yard for the
purpose of making or breaking up trains.
Trainship means a vessel other than a rail car ferry or carfloat,
specifically equipped to transport railroad vehicles, and fitted with
installed securing devices to tie down each vehicle.
Transport vehicle means a cargo-carrying vehicle such as an
automobile, van, tractor, truck, semitrailer, tank car or rail car used
for the transportation of cargo by any mode. Each cargo-carrying body
(trailer, rail car, etc.) is a separate transport vehicle.
UFC means Uniform Freight Classification.
UN means United Nations.
UN portable tank means a intermodal tank having a capacity of more
than 450 liters (118.9 gallons). It includes a shell fitted with service
equipment and structural equipment, including stabilizing members
external to the shell and skids, mountings or accessories to facilitate
mechanical handling. A UN portable tank must be capable of being filled
and discharged without the removal of its structural equipment and must
be capable of being lifted when full. Cargo tanks, rail tank car tanks,
non-metallic tanks, non-specification tanks, bulk bins, and IBCs and
packagings made to cylinder specifications are not UN portable tanks.
UN Recommendations means the UN Recommendations on the Transport of
Dangerous Goods.
UN standard packaging means a packaging conforming to standards in
the UN Recommendations.
Unit load device means any type of freight container, aircraft
container, aircraft pallet with a net, or aircraft pallet with a net
over an igloo.
United States means a State of the United States, the District of
Columbia, the Commonwealth of Puerto Rico, the Commonwealth of the
Northern Mariana Islands, the Virgin Islands, American Samoa, Guam, or
any other territory or possession of the United States designated by the
Secretary.
Vessel includes every description of watercraft, used or capable of
being used as a means of transportation on the water.
Viscous liquid means a liquid material which has a measured
viscosity in excess of 2500 centistokes at 25 deg.C. (77 deg.F.) when
determined in accordance with the procedures specified in ASTM Method D
445-72 ``Kinematic Viscosity of Transparent and Opaque Liquids (and the
Calculation of Dynamic Viscosity)'' or ASTM Method D 1200-70 ``Viscosity
of Paints, Varnishes, and Lacquers by Ford Viscosity Cup.''
Volatility refers to the relative rate of evaporation of materials
to assume the vapor state.
Water reactive material. See Sec. 173.124(c) of this subchapter.
Water resistant means having a degree of resistance to permeability
by and damage caused by water in liquid form.
Wooden barrel means a packaging made of natural wood, of round
cross-section, having convex walls, consisting of staves and heads and
fitted with hoops.
W.T. means watertight.
[Amdt. 171-32, 41 FR 15994, Apr. 15, 1976]
Editorial Note: For Federal Register citations affecting Sec. 171.8,
see the List of CFR Sections Affected which appears in the Finding Aids
section of the printed volume and on GPO Access.
Sec. 171.9 Rules of construction.
(a) In this subchapter, unless the context requires otherwise:
[[Page 86]]
(1) Words imparting the singular include the plural;
(2) Words imparting the plural include the singular; and
(3) Words imparting the masculine gender include the feminine;
(b) In this subchapter, the word: (1) ``Shall'' is used in an
imperative sense;
(2) ``Must'' is used in an imperative sense;
(3) ``Should'' is used in a recommendatory sense;
(4) ``May'' is used in a permissive sense to state authority or
permission to do the act described, and the words ``no person may * *
*'' or ``a person may not * * *'' means that no person is required,
authorized, or permitted to do the act described; and
(5) ``Includes'' is used as a word of inclusion not limitation.
[Amdt. 171-32, 41 FR 15996, Apr. 15, 1976, as amended by Amdt. 171-32A,
41 FR 40630, Sept. 20, 1976; Amdt. 171-121, 58 FR 51528, Oct. 1, 1993]
Sec. 171.10 Units of measure.
(a) General. To ensure compatibility with international
transportation standards, most units of measure in this subchapter are
expressed using the International System of Units (``SI'' or metric).
Where SI units appear, they are the regulatory standard. U.S. standard
or customary units, which appear in parentheses following the SI units,
are for information only and are not intended to be the regulatory
standard.
(b) Abbreviations for SI units of measure generally used throughout
this subchapter are as shown in paragraph (c) of this section. Customary
units shown throughout this subchapter are generally not abbreviated.
(c) Conversion values. (1) Conversion values are provided in the
following table and are based on values provided in ASTM E 380-89,
``Standard for Metric Practice.''
(2) If an exact conversion is needed, the following conversion table
should be used.
Table of Conversion Factors for SI Units
----------------------------------------------------------------------------------------------------------------
Measurement SI to U.S. standard U.S. standard to SI
----------------------------------------------------------------------------------------------------------------
Activity........................... 1 TBq=27 Ci................ 1 Ci=0.037 TBq
Length............................. 1 cm=0.3937008 in.......... 1 in=2.540000 cm
1 m=3.280840 ft............ 1 ft=0.3048000 m
Thickness.......................... 1 mm=0.03937008 in......... 1 in=25.40000 mm
Mass (weight)...................... 1 kg=2.204622 lb........... 1 lb=0.4535924 kg
1 g=0.03527397 oz.......... 1 oz=28.34952 g
Pressure........................... 1 kPa=0.1450377 psi........ 1 psi=6.894757 kPa
1 Bar=100 kPa=14.504 psi... 1 psi=0.06895 Bar
1 kPa=7.5 mm Hg............
Radiation level.................... 1 Sv/hr=100 rem/hr......... 1 rem/hr=0.01 Sv/hr
Volume (liquid).................... 1 L=0.2641720 gal.......... 1 gal=3.785412 L
1 mL=0.03381402 oz......... 1 oz=29.57353 mL
1 m\3\=35.31466 ft\3\...... 1 ft\3\=0.02831685 m\3\
Density............................ 1 kg/m\3\=0.06242797 lb/ 1 lb/ft\3\=16.01846 kg/m\3\
ft\3\.
Force.............................. 1 Newton = 0.2248 Pound- 1 Pound-force=4.483 N
force.
----------------------------------------------------------------------------------------------------------------
Abbreviation for units of measure are as follows:
Unit of measure and abbreviation:
(SI): millimeter, mm; centimeter, cm; meter, m; gram, g; kilogram, kg; kiloPascal, kPa; liter, L; milliliter,
mL; cubic meter, m\3\; Terabecquerel, TBq; Gigabecquerel, GBq; millisievert, mSv; Newton, N;
(U.S.): Inch, in; foot, ft; ounce, oz; pound, lb; psig, psi; gallon, gal; cubic feet, ft \3\; Curie, Ci;
millicurie, mCi; millirem, mrem.
[Amdt. 171-111, 56 FR 66159, Dec. 20, 1991, as amended by Amdt. 171-136,
60 FR 49108, Sept. 21, 1995; Amdt. 171-135, 60 FR 50302, Sept. 28, 1995;
66 FR 33335, June 21, 2001; 66 FR 45378, Aug. 28, 2001]
Sec. 171.11 Use of ICAO Technical Instructions.
Notwithstanding the requirements of parts 172 and 173 of this
subchapter, a hazardous material may be transported by aircraft, and by
motor vehicle either before or after being transported by aircraft, in
accordance with the ICAO Technical Instructions if the hazardous
material:
(a) Is packaged, marked, labeled, classified, described and
certified on a
[[Page 87]]
shipping paper and otherwise in a condition for shipment as required by
the ICAO Technical Instructions;
(b) Is within the quantity limits prescribed for transportation by
either passenger-carrying or cargo aircraft, as appropriate, as
specified in the ICAO Technical Instructions;
(c) Is not a forbidden material or package according to Sec. 173.21
of this subchapter or column 3 of the Sec. 172.101 table; and
(d) Fulfills the following additional requirements as applicable:
(1) For a material that meets the definition of a hazardous
substance as defined in this subchapter, the shipping paper and package
markings must conform to the provisions in Secs. 172.203(c) and 172.324,
respectively, of this subchapter.
(2) When a hazardous material, which is subject to the requirements
of the ICAO Technical Instructions, is also a hazardous waste as defined
in this subchapter:
(i) The word ``Waste'' must precede the proper shipping name on
shipping papers and package markings; and
(ii) It must comply with Sec. 172.205 with respect to the hazardous
waste manifests.
(3) When a hazardous material is not subject to the requirements of
the ICAO Technical Instructions, it must be transported as required by
this subchapter.
(4) When a hazardous material that is regulated by this subchapter
for transportation by highway is transported by motor vehicle on a
public highway under the provisions of this section, the following
requirements apply:
(i) The motor vehicle must be placarded in accordance with subpart F
of part 172 of this subchapter; and
(ii) The shipping paper may include an indication that the shipment
is being made under the provisions of this section or the letters
``ICAO.''
(5) Except for a Division 2.2 air bag, air bag module, or seat-belt
pretensioner, the shipping paper description must conform to the
requirements of Sec. 173.166(c) of this subchapter.
(6) For radioactive materials:
(i) Shipping papers for highway route controlled quantity
radioactive materials shipments must meet the requirements of
Sec. 172.203(d)(4) of this subchapter.
(ii) Competent authority certification and any necessary
revalidation for Type B, Type B(U), Type B(M), and fissile materials
packages must be obtained from the appropriate authorities as specifed
in Secs. 173.471, 173.472 and 173.473 of this subchapter, and all
requirements of the certificates and revalidations must be met.
(iii) Except for limited quantities of Class 7 (radioactive)
material, the provisions of Secs. 172.204(c)(4), 173.448(e), (f) and
(g)(3) of this subchapter apply.
(iv) Limited quantities of radioactive materials must meet the
provisions of Sec. 173.421, Sec. 173.424 or Sec. 173.426 as appropriate
of this subchapter.
(v) Type A package contents shall be limited in accordance with
Sec. 173.431 of this subchapter.
(vi) The definition for ``radioactive material'' in Sec. 173.403 of
this subchapter applies to radioactive materials transported under the
provisions of this section.
(7) If a United States variation is indicated in the ICAO Technical
Instructions for any provision governing the transport of the hazardous
material, the hazardous material is transported in conformance with that
variation.
(8) Abbreviations may not be used in shipping paper entries or
package markings unless they are specifically authorized by this
subchapter. ICAO class or division numbers are not considered to be
abbreviations.
(9) When a hazardous material, which is subject to the requirements
of the ICAO Technical Instructions, is a material poisonous by
inhalation (see Sec. 171.8 of this subchapter)--
(i) The shipping description must include the words ``Toxic
Inhalation Hazard'' or ``Poison-Inhalation Hazard'' or ``Inhalation
Hazard'', as required in Sec. 172.203(m) of this subchapter;
(ii) The material must be packaged in accordance with the
requirements of this subchapter; and
(iii) The package must be marked in accordance with Sec. 172.313 of
this subchapter and labeled with ``POISON INHALATION HAZARD'' or
``POISON GAS'', as appropriate, in accordance with subpart E of part 172
of this subchapter.
[[Page 88]]
(10) Shipments of hazardous materials under this section must
conform to the requirements for emergency response information as
prescribed in subpart G of part 172 of this subchapter.
(11) Packages of Class 1 (explosive) materials must be marked in
accordance with Sec. 172.320 of this subchapter.
(12) If an ammonium nitrate fertilizer or ammonium nitrate mixed
fertilizer, must not meet the definition and criteria of a Class 1
(explosive) material.
(13) Transportation of marine pollutants, as defined in Sec. 171.8
of this subchapter, in bulk packagings must conform to the requirements
of Secs. 172.203(l) and 172.322 of this subchapter.
(14) Except as provided for limited quantities of compressed gases
in containers of not more than 4 fluid ounces capacity under
Sec. 173.306(a)(1) of this subchapter, aerosols must meet the definition
for ``Aerosol'' in Sec. 171.8. In addition, an aerosol must be in a
metal packaging if the packaging exceeds 7.22 cubic inches.
(15) A chemical oxygen generator is forbidden for transportation
aboard a passenger-carrying aircraft and must be approved, classed,
described and packaged in accordance with the requirements of this
subchapter for transportation on cargo-only aircraft. A chemical oxygen
generator (spent) is forbidden for transportation on aircraft.
(16) A cylinder containing Oxygen, compressed, may not be
transported on a passenger-carrying aircraft or in an inaccessible cargo
location aboard a cargo-only aircraft unless it is packaged as required
by Part 173 and Part 178 of this subchapter and is placed in an overpack
or outer packaging that satisfies the requirements of Special Provision
A52 in Sec. 172.102.
(17) An organic peroxide that is not identified by technical name in
the Organic Peroxide Table in Sec. 173.225(b) of this subchapter must be
approved by the Associate Administrator in accordance with the
requirements of Sec. 173.128(d) of this subchapter.
[Amdt. 171-69, 47 FR 54821, Dec. 6, 1982]
Editorial Note: For Federal Register citations affecting
Sec. 171.11, see the List of CFR Sections Affected which appears in the
Finding Aids section of the printed volume and on GPO Access.
Sec. 171.12 Import and export shipments.
(a) Importer's responsibility. Except in the case of a shipment from
Canada conforming to Sec. 171.12a of this subchapter, each person
importing a hazardous material into the United States shall provide the
shipper and the forwarding agent at the place of entry into the United
States timely and complete information as to the requirements of this
subchapter that will apply to the shipment of the material within the
United States. The shipper, directly or through the forwarding agent at
the place of entry, shall provide the initial carrier in the United
States the certificate of compliance required by Sec. 172.204 of this
subchapter. The carrier may not accept the material for transportation
unless the required certification is provided. All shipping paper
information required under paragraph (b) or (d) of this section must be
in English.
(b) IMDG Code (see Sec. 171.7 of this subchapter). The IMDG Code
sets forth descriptions, classifications, packagings, labeling and
vessel stowage requirements. Notwithstanding the provisions of this
subchapter, a material which is packaged, marked, classed, labeled,
placarded, described, stowed and segregated, and certified (including a
container packing certification, if applicable) in accordance with the
IMDG Code, and otherwise conforms to the requirements of this section,
may be offered and accepted for transportation and transported within
the United States. The following conditions and limitations apply:
(1) The provisions of this paragraph (b) apply only if all or part
of the transportation is by vessel.
(2) A number of materials listed in the IMDG Code are not subject to
the requirements of this subchapter. The provisions of this subchapter
do not apply to materials listed in the IMDG Code which are not
designated as hazardous materials under this subchapter. These materials
may, however, be transported in the U.S. when described, marked and
labeled in accordance with the IMDG Code.
[[Page 89]]
(3) A material designated as a hazardous material under this
subchapter which is not subject to the requirements of the IMDG Code may
not be transported under the provisions of this section. For example,
internal combustion engines, and viscous flammable liquids having a
flash point of 23 deg.C (73.4 deg.F) or greater and less than or equal
to 60.5 deg.C (140.9 deg.F) as provided in 2.3.2.5 of the IMDG Code
may not be transported under the provisions of this section and are
subject to the requirements of this subchapter.
(4) A forbidden material or package according to Sec. 173.21 of this
subchapter or column 3 of the Sec. 172.101 table may not be transported
under the provisions of this section.
(5) Except for IBCs and UN portable tanks intended for liquids or
solids, hazardous materials that conform to the requirements of the IMDG
Code, bulk packagings must conform to the requirements of this
subchapter. For UN portable tanks, Special Provisions TP37, TP38, TP44
and TP45 must be met when applicable. Except as specified in paragraph
(b)(8) of this section for a material poisonous (toxic) by inhalation
(see Sec. 171.8 of this subchapter), the T Codes specified for specific
hazardous materials in Column 13 of the Dangerous Goods List of the IMDG
Code may be applied to the transportation of those materials in IM, IMO
and DOT Specification 51 portable tanks.
(6) For export, packagings must conform to the applicable
requirements in Secs. 173.24, 173.24a and 173.28 of this subchapter.
(7) A Class 1 material must be classed and approved under the
procedures in subpart C of part 173 of this subchapter and conform to
the requirements of Sec. 172.320 and part 176 of this subchapter.
(8) When a hazardous material, which is subject to the requirements
of the IMDG Code, is a material poisonous by inhalation (see Sec. 171.8
of this subchapter)--
(i) The shipping description must include the words `Toxic
Inhalation Hazard' or ``Poison-Inhalation Hazard'' or ``Inhalation
Hazard'', as required in Sec. 172.203(m) of this subchapter;
(ii) The material must be packaged in accordance with the
requirements of this subchapter;
(iii) The package must be marked in accordance with Sec. 172.313 of
this subchapter;
(iv) Except as provided in paragraph (b)(8)(v) of this section, the
package must be labeled or placarded POISON GAS or POISON INHALATION
HAZARD, as appropriate, in accordance with subparts E and F of this
subchapter;
(v) A label or placard that conforms to IMDG Code specifications for
a ``Class 2.3'' or ``Class 6.1'' label or placard may be substituted for
the POISON GAS or POISON INHALATION HAZARD label or placard required by
paragraph (b)(8)(iv) of this section on a package transported in a
closed transport vehicle or freight container. The transport vehicle or
freight container must be marked with identification numbers for the
hazardous material, regardless of the total quantity contained in the
transport vehicle or freight container, in the manner specified in
Sec. 172.313(c) of this subchapter and placarded as required by subpart
F of this subchapter;
(vi) A package, freight container, or transport vehicle may be
placarded in conformance with IMDG Code placard specifications for
``Class 2.3'' or ``Class 6.1'', as appropriate, in place of the POISON
GAS or POISON INHALATION HAZARD placard required by paragraph (b)(8)(iv)
of this section when moving within a single port area, including
contiguous harbor.
(9) Class 7 materials must conform to the provisions of paragraph
(d) of this section.
(10) For a hazardous waste, as defined in this subchapter--
(i) The word ``Waste'' must precede the proper shipping name on
shipping papers and packages; and
(ii) The requirements of Sec. 172.205 of this subchapter with
respect to hazardous waste manifests are applicable.
(11) A hazardous substance as defined in this subchapter must
conform to the requirements of Secs. 172.203(c) and 172.324 of this
subchapter.
(12) A poisonous material must conform to the requirements of
Sec. 172.203(m) of this subchapter.
[[Page 90]]
(13) [Reserved]
(14) Any ammonium nitrate fertilizer or ammonium nitrate mixed
fertilizer must not meet the definition and criteria of a Class 1
(explosive) material.
(15) Cylinders not manufactured to DOT specifications must conform
to the requirements of Sec. 173.301(i) and (j) of this subchapter.
(16) Shipments of hazardous materials under this section must
conform to the requirements for emergency response information as
prescribed in subpart G of part 172 of this subchapter.
(17) Except as provided for limited quantities of compressed gases
in containers of not more than 4 fluid ounces capacity under
Sec. 173.306(a)(1) of this subchapter, aerosols must meet the definition
for ``Aerosol'' in Sec. 171.8.
(18) A chemical oxygen generator must be approved in accordance with
the requirements of this subchapter. A chemical oxygen generator and a
chemical oxygen generator (spent) must be classed, described and
packaged in accordance with the requirements of this subchapter.
(19) Except for Division 2.2, the shipping paper description for an
air bag, air bag module, or seat-belt pretensioner must conform to the
requirements of Sec. 173.166(c) of this subchapter.
(20) An organic peroxide that is not identified by technical name in
the Organic Peroxide Table in Sec. 173.225(b) of this subchapter must be
approved by the Associate Administrator in accordance with the
requirements of Sec. 173.128(d) of this subchapter.
(c) Use of IMDG Code in port areas. Section 171.2 notwithstanding, a
hazardous material (other than Division 1.1 or 1.2 or Class 7) being
imported into or exported from the United States or passing through the
United States in the course of being shipped between places outside the
United States may be offered and accepted for transportation and
transported by motor vehicle within a single port area (including
contiguous harbors) when packaged, marked, classed, labeled, stowed and
segregated in accordance with the IMDG Code, if the hazardous material
is offered and accepted in accordance with the requirements of subparts
C and F of part 172 of this subchapter pertaining to shipping papers and
placarding and otherwise conforms to the applicable requirements of part
176 of this subchapter. The requirement in Sec. 172.201(d) of this
subchapter for an emergency telephone number does not apply to shipments
made in accordance with the IMDG Code if the hazardous material:
(1) Is not offloaded from the vessel;
(2) Is offloaded between ocean vessels at a U.S. port facility
without being transported by public highway.
(d) Use of International Atomic Energy Agency (IAEA) regulations for
Class 7 (radioactive) materials. Class 7 (radioactive) materials being
imported into or exported from the United States, or passing through the
United States in the course of being shipped between places outside the
United States, may be offered and accepted for transportation when
packaged, marked, labeled, and otherwise prepared for shipment in
accordance with IAEA ``Regulations for the Safe Transport of Radioactive
Material,'' Safety Series No. 6, 1985 edition, or TS-R-1, 1996 edition
(see Sec. 171.7) , if--
(1) Highway route controlled quantities (see Sec. 173.403 of this
subchapter) are shipped in accordance with Secs. 172.203(d)(4), 172.507
and 173.22(c) of this subchapter;
(2) For fissile materials and Type B packages, the competent
authority certification and any necessary revalidation is obtained from
the appropriate competent authorities as specified in Secs. 173.471,
173.472 and 173.473 of this subchapter and all requirements of the
certificates and revalidations are met;
(3) Type A package contents are limited in accordance with
Sec. 173.431 of this subchapter;
(4) The country of origin for the shipment has adopted the
corresponding edition (Safety Series No. 6, 1985 Edition, or TS-R-1,
1996 Edition) of the IAEA ``Regulations for the Safe Transport of
Radioactive Material';
(5) The requirements of Secs. 173.448(e), 173.448(f), and
173.448(g)(3) of this subchapter are fulfilled, when applicable;
(6) Shipments comply with the requirements for emergency response
information prescribed in subpart G of part 172 of this subchapter; and
[[Page 91]]
(7) The definition for ``radioactive material'' in Sec. 173.403 of
this subchapter is applied to radioactive materials transported under
the provisions of this section.
(e) Shipments to or from Mexico. Unless otherwise excepted,
hazardous materials shipments from Mexico to the United States or from
the United States to Mexico must conform to all applicable requirements
of this subchapter. When a hazardous material that is a material
poisonous by inhalation (see Sec. 171.8) is transported by highway or
rail from Mexico to the United States, or from the United States to
Mexico, the following requirements apply:
(1) The shipping description must include the words ``Toxic
Inhalation Hazard'' or ``Poison-Inhalation Hazard'' or ``Inhalation
Hazard'', as required in Sec. 172.203(m) of this subchapter.
(2) The material must be packaged in accordance with requirements of
this subchapter.
(3) The package must be marked in accordance with Sec. 172.313 of
this subchapter.
(4) Except as provided in paragraph (c)(5) of this section, the
package must be labeled or placarded POISON GAS or POISON INHALATION
HAZARD, as appropriate, in accordance with subparts E and F of this
subchapter.
(5) A label or placard that conforms to the UN Recommendations on
the Transport of Dangerous Goods specifications for a ``Division 2.3''
or ``Division 6.1'' label or placard may be substituted for the POISON
GAS or POISON INHALATION HAZARD label or placard required by
Secs. 172.400(a) and 172.504(e) of this subchapter on a package
transported in a closed transport vehicle or freight container. The
transport vehicle or freight container must be marked with
identification numbers for the material, regardless of the total
quantity contained in the transport vehicle or freight container, in the
manner specified in Sec. 172.313(c) of this subchapter and placarded as
required by subpart F of this subchapter.
[Amdt. 171-111, 55 FR 52472, Dec. 21, 1990]
Editorial Note: For Federal Register citations affecting
Sec. 171.12, see the List of CFR Sections Affected which appears in the
Finding Aids section of the printed volume and on GPO Access.
Sec. 171.12a Canadian shipments and packagings.
(a) Scope and applicability. This section sets forth provisions for
the transportation by rail or highway of shipments of hazardous
materials which conform to the regulations of the Government of Canada
but which may differ from the requirements of this subchapter with
regard to hazard communication, classification or packaging. Except as
provided in paragraph (b)(5)(iv) of this section, the provisions apply
only to shipments which originate in Canada and either terminate in the
U.S. or transit the U.S. to a Canadian or foreign destination, and to
the return to Canada of empty bulk packages containing residues of
hazardous materials which originally were imported into the U.S.
Reciprocal provisions, applicable to exports from the U.S., appear in
the regulations of the Government of Canada.
(b) Conditions and limitations. Notwithstanding the requirements of
parts 172, 173, and 178 of this subchapter, and subject to the
limitations of paragraph (a) of this section, a hazardous material that
is classed, marked, labeled, placarded, described on a shipping paper,
and packaged in accordance with the Transportation of Dangerous Goods
(TDG) Regulations issued by the Government of Canada may be offered for
transportation and transported to or through the United States by motor
vehicle or rail car. Copies of the TDG Regulations may be obtained from
the Canadian Government Publishing Centre, Ottawa, Ontario K1A 059;
Telephone (819) 956-4800. The following conditions and limitations
apply:
(1) A number of materials listed in the TDG Regulations may not be
subject to the requirements of this subchapter. The provisions of this
subchapter do not apply to materials listed in the TDG Regulations which
are not designated as hazardous materials under this subchapter. These
materials may, however, be transported in the U.S. when described,
marked and labeled in accordance with the TDG Regulations.
[[Page 92]]
(2) A material designated as a hazardous material under this
subchapter which is not subject to the requirements of the TDG
Regulations may not be transported under the provisions of this section.
(3) A forbidden material or package according to Sec. 173.21 of this
subchapter or column 3 of the Sec. 172.101 table may not be transported
under the provisions of this section.
(4) A Class 1 material must be classed and approved under the
procedures in subpart C of part 173 of this subchapter, and packages of
Class 1 materials must be marked in accordance with Sec. 172.320 of this
subchapter.
(5) When a hazardous material, which is a material poisonous by
inhalation under the provisions of this subchapter (see Sec. 171.8 of
this subchapter), is subject to the requirements of the TDG
Regulations--
(i) The shipping description must include the words `Toxic
Inhalation Hazard' or `Poison Inhalation Hazard' or ``Inhalation
Hazard'', as required in Sec. 172.203(m) of this subchapter;
(ii) The material must be packaged in accordance with the
requirements of this subchapter;
(iii) The package must be marked in accordance with Sec. 172.313 of
this subchapter;
(iv) Except as provided in paragraph (b)(5)(v) of this section and
for a package containing anhydrous ammonia, the package must be labeled
or placarded POISON GAS or POISON INHALATION HAZARD, as appropriate, in
accordance with subparts E and F of this subchapter;
(v) A label or placard that conforms to the specifications in the
TDG Regulations for a ``Class 2.3'' or ``Class 6.1'' label or placard
may be substituted for the POISON GAS or POISON INHALATION HAZARD label
or placard required by paragraph (b)(5)(iv) of this section on a package
transported in a closed transport vehicle or freight container. The
transport vehicle or freight container must be marked with
identification numbers for the material, regardless of quantity, in the
manner specified in Sec. 172.313(c) of this subchapter and placarded as
required by subpart F of this subchapter. When moving in the United
States, the transport vehicle or freight container may also be placarded
in accordance with the appropriate TDG regulations in addition to the
POISON GAS or POISON INHALATION HAZARD placards required by paragraph
(b)(5)(iv) of this section;
(vi) For shipments of anhydrous ammonia, the shipping paper must
contain an indication that the markings, labels and placards have been
applied in conformance with the TDG Regulations and this paragraph
(b)(5).
(6) Required shipping descriptions and package markings must be in
English. Abbreviations may not be used unless specifically authorized by
this subchapter. Identification numbers must be preceded by ``UN'' or
``NA''. The use of an identification number preceded by ``PIN'' is not
authorized.
(7) Shipments must conform to the requirements for emergency
response information in subpart G of part 172 of this subchapter.
(8) A Class 7 material must conform to the provisions of
Sec. 171.12(d) of this subchapter;
(9) For a hazardous waste as defined in this subchapter--
(i) The word ``Waste'' must precede the proper shipping name on
shipping papers and packages; and
(ii) The requirements of Sec. 172.205 of this subchapter with
respect to hazardous waste manifests are applicable;
(10) A hazardous substance as defined in this subchapter must
conform to the requirements of Secs. 172.203(c) and 172.324 of this
subchapter; and
(11) A poisonous material must conform to the requirements of
Sec. 172.203(m) of this subchapter.
(12) [Reserved]
(13) When the provisions of this subchapter require that a DOT
specification or UN standard packaging must be used for a hazardous
material, a packaging authorized by the TDG Regulations may be used only
if it corresponds to the DOT specification or UN packaging authorized by
this subchapter. Cylinders not manufactured to DOT specifications must
conform to the requirements of Sec. 173.301(i) and (j) of this
subchapter.
(14) Any ammonium nitrate fertilizer or ammonium nitrate mixed
fertilizer
[[Page 93]]
must not meet the definition and criteria of a Class 1 (explosive)
material.
(15) Transportation of marine pollutants, as defined in Sec. 171.8
of this subchapter, must conform to the requirements of Secs. 172.203(l)
and 172.322 of this subchapter.
(16) Except as provided for limited quantities of compressed gases
in containers of not more than 4 fluid ounces capacity under
Sec. 173.306(a)(1) of this subchapter, aerosols must meet the definition
for ``Aerosol'' in Sec. 171.8.
(17) A chemical oxygen generator must be approved in accordance with
the requirements of this subchapter. A chemical oxygen generator and a
chemical oxygen generator (spent) must be classed, described and
packaged in accordance with the requirements of this subchapter.
(18) An organic peroxide that is not identified by technical name in
the Organic Peroxide Table in Sec. 173.225(b) of this subchapter must be
approved by the Associate Administrator in accordance with the
requirements of Sec. 173.128(d) of this subchapter.
[Amdt. 171-111, 55 FR 52473, Dec. 21, 1990, as amended at 56 FR 66160,
Dec. 20, 1991; 57 FR 45453, Oct. 1, 1992; Amdt. 171-116, 57 FR 52935,
Nov. 5, 1992; Amdt. 171-153, 62 FR 24700, May 6, 1997; 62 FR 30770, June
5, 1997; 64 FR 10753, Mar. 5, 1999; 64 FR 45396, Aug. 19, 1999; 64 FR
50262, Sept. 16, 1999; 64 FR 51720, Sept. 24, 1999; 64 FR 51915, Sept.
27, 1999; 66 FR 33336, June 21, 2001; 66 FR 44255, Aug. 22, 2001]
Sec. 171.14 Transitional provisions for implementing certain requirements.
General. The purpose of the provisions of this section is to provide
an orderly transition to certain new requirements so as to minimize any
burdens associated with them.
(a) Previously filled packages--(1) Packages filled prior to October
1, 1991. Notwithstanding the marking and labeling provisions of subparts
D and E, respectively, of part 172, and the packaging provisions of part
173 and subpart B of part 172 of this subchapter, a package may be
offered for transportation and transported prior to October 1, 2001, if
it--
(i) Conforms to the old requirements of this subchapter in effect on
September 30, 1991;
(ii) Was filled with a hazardous material prior to October 1, 1991;
(iii) Is marked ``Inhalation Hazard'' if appropriate, in accordance
with Sec. 172.313 of this subchapter or Special Provision 13, as
assigned in the Sec. 172.101 table; and
(iv) Is not emptied and refilled on or after October 1, 1991.
(2) Non-bulk packages filled prior to October 1, 1996.
Notwithstanding the packaging provisions of subpart B of part 172 and
the packaging provisions of part 173 of this subchapter with respect to
UN standard packagings, a non-bulk package other than a cylinder may be
offered for transportation and transported domestically prior to October
1, 1999, if it--
(i) Conforms to the requirements of this subchapter in effect on
September 30, 1996;
(ii) Was filled with a hazardous material prior to October 1, 1996;
and
(iii) Is not emptied and refilled on or after October 1, 1996.
(b) Transitional placarding provisions. Until October 1, 2001,
placards which conform to specifications for placards in effect on
September 30, 1991, or placards specified in the December 21, 1990 final
rule may be used, for highway transportation only, in place of the
placards specified in subpart F of part 172 of this subchapter, in
accordance with the following table:
Placard Substitution Table
------------------------------------------------------------------------
Current placard Old (Sept. 30, 1991)
Hazard class or division No. name placard name
------------------------------------------------------------------------
Division 1.1................. Explosives 1.1. Explosives A.
Division 1.2................. Explosives 1.2. Explosives A.
Division 1.3................. Explosives 1.3. Explosives B.
Division 1.4................. Explosives 1.4. Dangerous.
Division 1.5................. Explosives 1.5. Blasting agents.
Division 1.6................. Explosives 1.6. Dangerous.
Division 2.1................. Flammable gas.. Flammable gas.
Division 2.2................. Nonflammable Nonflammable gas.
gas.
Division 2.3\1\.............. Poison gas..... Poison gas.
[[Page 94]]
Class 3...................... Flammable...... Flammable.
Combustible liquid........... Combustible.... Combustible.
Division 4.1................. Flammable solid Flammable solid.
Division 4.2................. Spontaneously Flammable solid.
combustible.
Division 4.3................. Dangerous when Flammable solid W.
wet.
Division 5.1................. Oxidizer....... Oxidizer.
Division 5.2................. Organic Organic peroxide.
peroxide.
Division 6.1, (inhalation Poison Poison.
hazard, Zone A or B)\1\. inhalation
hazard.
Division 6.1, PG I (other Posion......... Poison.
than Zone A or B inhalation
hazard), PG II, or PG III.
Class 7...................... Radioactive.... Radioactive.
Class 8...................... Corrosive...... Corrosive.
Class 9...................... Class 9........ (none required).
------------------------------------------------------------------------
\1\ For materials poisonous by inhalation, by all modes of
transportation, until October 1, 2001, placards may be used that
conform to specifications for placards (1) in effect on September 30,
1991, (2) specified in the December 21, 1990 final rule, or (3)
specified in the July 22, 1997 final rule.
(c) Non-specification fiber drums. A non-specification fiber drum
with a removable head is authorized for a liquid hazardous material in
Packing Group III that is not poisonous by inhalation for which the
packaging was authorized under the requirements of part 172 or part 173
of this subchapter in effect on September 30, 1991. This authorization
expires on the date on which funds are authorized to be appropriated to
carry out chapter 51 of title 49, United States Code (related to
transportation of hazardous materials), for fiscal years beginning after
September 30, 1997. Information concerning this funding authorization
date may be obtained by contacting the Office of the Associate
Administrator.
(d) A final rule published in the Federal Register on June 21, 2001,
effective October 1, 2001, resulted in revisions to this subchapter.
During the transition period, until October 1, 2002, as provided in
paragraph (d)(1) of this section, a person may elect to comply with
either the applicable requirements of this subchapter in effect on
September 30, 2001, or the requirements published in the June 21, 2001
final rule.
(1) Transition dates. The effective date of the June 21, 2001 final
rule is October 1, 2001. A delayed compliance date of October 1, 2002 is
authorized. On October 1, 2002, all applicable regulatory requirements
adopted in the June 21, 2001 final rule in effect on October 1, 2001
must be met.
(2) Intermixing old and new requirements. Prior to October 1, 2002,
it is recommended that the hazard communication requirements be
consistent where practicable. Marking, labeling, placarding, and
shipping paper descriptions should conform to either the old
requirements of this subchapter in effect on September 30, 2001, or the
new requirements of this subchapter in the June 21, 2001 final rule
without intermixing communication elements. However, intermixing is
permitted, during the applicable transition period, for packaging,
hazard communication, and handling provisions, as follows:
(i) If either shipping names or identification numbers are
identical, a shipping paper may display the old shipping description
even if the package is marked and labeled under the new shipping
description;
(ii) If either shipping names or identification numbers are
identical, a shipping paper may display the new shipping description
even if the package is marked and labeled under the old shipping
description; and
(iii) Either old or new placards may be used regardless of whether
old or new shipping descriptions and package markings are used.
(3) Until October 1, 2003, the KEEP AWAY FROM FOOD labeling and
placarding requirements in effect on September 30, 1999, may continue to
be used in place of the new requirements for Division 6.1, Packing Group
III materials.
(4) Until January 1, 2010, a hazardous material may be transported
in an IM or IMO portable tank in accordance
[[Page 95]]
with the T Codes (Special Provisions) assigned to a hazardous material
in Column (7) of the HMT in effect on September 30, 2001.
(5) Until October 1, 2005, proper shipping names that included the
word ``inhibited'' prior to the June 21, 2001 final rule in effect on
October 1, 2001, may continue to be shown on packagings in place of
``stabilized.''
[Amdt. 171-131, 59 FR 67406, Dec. 29, 1994, as amended by Amdt. 171-132,
60 FR 26799, 26800, May 18, 1995; Amdt. 171-138, 60 FR 48786, Sept. 20,
1995; Amdt. 171-139, 61 FR 7958, Feb. 29, 1996; Amdt. 171-150, 62 FR
1227, Jan. 8, 1997; Amdt 171-153, 62 FR 24700, May 6, 1997; 62 FR 29676,
June 2, 1997; 62 FR 39404, July 22, 1997; 63 FR 52847, Oct. 1, 1998; 64
FR 10753, Mar. 5, 1999; 64 FR 50263, Sept. 16, 1999; 64 FR 51915, Sept.
27, 1999; 66 FR 33336, June 21, 2001; 66 FR 45378, Aug. 28, 2001]
Sec. 171.15 Immediate notice of certain hazardous materials incidents.
(a) At the earliest practicable moment, each carrier who transports
hazardous materials (including hazardous wastes) shall give notice in
accordance with paragraph (b) of this section after each incident that
occurs during the course of transportation (including loading, unloading
and temporary storage) in which--
(1) As a direct result of hazardous materials--
(i) A person is killed; or
(ii) A person receives injuries requiring his or her
hospitalization; or
(iii) Estimated carrier or other property damage exceeds $50,000; or
(iv) An evacuation of the general public occurs lasting one or more
hours; or
(v) One or more major transportation arteries or facilities are
closed or shut down for one hour or more; or
(vi) The operational flight pattern or routine of an aircraft is
altered; or
(2) Fire, breakage, spillage, or suspected radioactive contamination
occurs involving shipment of radioactive material; or
(3) Fire, breakage, spillage, or suspected contamination occurs
involving shipment of infectious substances (etiologic agents); or
(4) There has been a release of a marine pollutant in a quantity
exceeding 450 L (119 gallons) for liquids or 400 kg (882 pounds) for
solids; or
(5) A situation exists of such a nature (e.g., a continuing danger
to life exists at the scene of the incident) that, in the judgment of
the carrier, it should be reported to the National Response Center even
though it does not meet the criteria of paragraph (a) (1), (2) or (3) of
this section.
(b) Except for transportation by aircraft, each notice required by
paragraph (a) of this section shall be given to the National Response
Center by telephone (toll-free) on 800-424-8802. Notice involving
shipments transported by aircraft must be given to the nearest FAA Civil
Aviation Security Office by telephone at the earliest practical moment
after each incident in place of the notice to the National Response
Center. Notice involving etiologic agents may be given to the Director,
Centers for Disease Control, U.S. Public Health Service, Atlanta, Ga.
(800) 232-0124, in place of the notice to the National Response Center
or (toll call) on 202-267-2675. Each notice must include the following
information:
(1) Name of reporter.
(2) Name and address of carrier represented by reporter.
(3) Phone number where reporter can be contacted.
(4) Date, time, and location of incident.
(5) The extent of injuries, if any.
(6) Classification, name, and quantity of hazardous materials
involved, if such information is available.
(7) Type of incident and nature of hazardous material involvement
and whether a continuing danger to life exists at the scene.
(c) Each carrier making a report under this section shall also make
the report required by Sec. 171.16.
Note: Under 40 CFR 302.6 EPA requires persons in charge of
facilities (including transport vehicles, vessels and aircraft) to
report any release of a hazardous substance in a quantity equal to or
greater than its reportable quantity, as soon as that person has
knowledge of the release, to the U.S. Coast Guard National Response
Center at (toll free) 800-424-8802 or (toll) 202-267-2675.
[Amdt. 171-7, 35 FR 16837, Oct. 3, 1970]
Editorial Note: For Federal Register citations affecting
Sec. 171.15, see the List of CFR Sections Affected which appears in the
Finding Aids section of the printed volume and on GPO Access.
[[Page 96]]
Sec. 171.16 Detailed hazardous materials incident reports.
(a) Each carrier who transports hazardous materials shall report in
writing, in duplicate, on DOT Form F 5800.1 (Rev. 6/89) to the
Department within 30 days of the date of discovery, each incident that
occurs during the course of transportation (including loading,
unloading, and temporary storage) in which any of the circumstances set
forth in Sec. 171.15(a) occurs or there has been an unintentional
release of hazardous materials from a package (including a tank) or any
quantity of hazardous waste has been discharged during transportation.
If a report pertains to a hazardous waste discharge:
(1) A copy of the hazardous waste manifest for the waste must be
attached to the report; and
(2) An estimate of the quantity of the waste removed from the scene,
the name and address of the facility to which it was taken, and the
manner of disposition of any removed waste must be entered in Section IX
of the report form (Form F 5800.1) (Rev. 6/89).
(b) Each carrier making a report under this section shall send the
report to the Information Systems Manager, DHM-63, Research and Special
Programs Administration, Department of Transportation, Washington, DC
20590-0001; and, for incidents involving transportation by aircraft, a
copy of the report shall also be sent to the FAA Civil Aviation Security
Office nearest the location of the incident. A copy of the report shall
be retained for a period of two years, at the carrier's principal place
of business, or at other places as authorized and approved in writing by
an agency of the Department of Transportation.
(c) Except as provided in paragraph (d) of this section, the
requirements of paragraph (a) of this section do not apply to incidents
involving the unintentional release of a hazardous material--
(1) Transported under one of the following proper shipping names:
(i) Consumer commodity.
(ii) Battery, electric storage, wet, filled with acid or alkali.
(iii) Paint and paint related material when shipped in a packaging
of five gallons or less.
(2) Prepared and transported as a limited quantity shipment in
accordance with this subchapter.
(d) The exceptions to incident reporting provided in paragraph (c)
of this section do not apply to:
(1) Incidents required to be reported under Sec. 171.15(a);
(2) Incidents involving transportation aboard aircraft;
(3) Except for consumer commodities, materials in Packing Group I;
or
(4) Incidents involving the transportation of hazardous waste.
Note: A guideline document for assisting in the completion of DOT
Form F 5800.1 (Rev. 6/89) may be obtained from the Office of Hazardous
Materials Transportation, DHM-51, U.S. Department of Transportation,
Washington, DC 20590-0001.
[Amdt. 171-7, 35 FR 16837, Oct. 3, 1970, as amended by Amdt. 171-56, 45
FR 73683, Nov. 6, 1980; Amdt. No. 171-65, 47 FR 24584, June 7, 1982;
Amdt. 171-72, 48 FR 17095, Apr. 21, 1983; Amdt. 171-101, 54 FR 25813,
June 19, 1989; Amdt. 171-109, 55 FR 39978, Oct. 1, 1990; Amdt. 171-140,
61 FR 18932, Apr. 29, 1996; Amdt. 171-145, 61 FR 27172, May 30, 1996]
Secs. 171.17-171.18 [Reserved]
Sec. 171.19 Approvals or authorizations issued by the Bureau of Explosives.
Effective December 31, 1998, approvals or authorizations issued by
the Bureau of Explosives (BOE), other than those issued under part 179
of this subchapter, are no longer valid.
[63 FR 37459, July 10, 1998]
Sec. 171.20 Submission of Examination Reports.
(a) When it is required in this subchapter that the issuance of an
approval by the Associate Administrator be based on an examination by
the Bureau of Explosives (or any other test facility recognized by
RSPA), it is the responsibility of the applicant to submit the results
of the examination to the Associate Administrator.
(b) Applications for approval submitted under paragraph (a) of this
section, must be submitted to the Associate Administrator for Hazardous
Materials Safety, Research and Special Programs Administration,
Washington, DC 20590-0001.
[[Page 97]]
(c) Any applicant for an approval aggrieved by an action taken by
the Associate Administrator, under this subpart may file an appeal with
the Administrator, RSPA within 30 days of service of notification of a
denial.
[Amdt. 171-54, 45 FR 32692, May 19, 1980, as amended by Amdt. 171-66, 47
FR 43064, Sept. 30, 1982; Amdt. 171-109, 55 FR 39978, Oct. 1, 1990;
Amdt. 171-111, 56 FR 66162, Dec. 20, 1991; 66 FR 45378, Aug. 28, 2001]
Sec. 171.21 Assistance in investigations and special studies.
(a) A carrier who is responsible for reporting an incident under the
provisions of Sec. 171.16 shall make all records and information
pertaining to the incident available to an authorized representative or
special agent of the Department upon request. The carrier shall give an
authorized representative or special agent of the Department reasonable
assistance in the investigation of the incident.
(b) If the Department makes an inquiry to a carrier of hazardous
materials in connection with a study of incidents, the carrier shall--
(1) Respond to the inquiry within 30 days after its receipt or
within such other time as the inquiry may specify; and
(2) Provide full, true, and correct answers to any questions
included in the inquiry.
[Amdt. 171-101, 54 FR 25813, June 19, 1989, as amended at 66 FR 45378,
Aug. 28, 2001]
PART 172--HAZARDOUS MATERIALS TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, AND TRAINING REQUIREMENTS--Table of Contents
Subpart A--General
Sec.
172.1 Purpose and scope.
172.3 Applicability.
Subpart B--Table of Hazardous Materials and Special Provisions
172.101 Purpose and use of hazardous materials table.
172.102 Special provisions.
Subpart C--Shipping Papers
172.200 Applicability.
172.201 General entries.
172.202 Description of hazardous material on shipping papers.
172.203 Additional description requirements.
172.204 Shipper's certification.
172.205 Hazardous waste manifest.
Subpart D--Marking
172.300 Applicability.
172.301 General marking requirements for non-bulk packagings.
172.302 General marking requirements for bulk packagings.
172.303 Prohibited marking.
172.304 Marking requirements.
172.306 [Reserved]
172.308 Authorized abbreviations.
172.310 Class 7 (radioactive) materials.
172.312 Liquid hazardous materials in non-bulk packagings.
172.313 Poisonous hazardous materials.
172.316 Packagings containing materials classed as ORM-D.
172.320 Explosive hazardous materials.
172.322 Marine pollutants.
172.324 Hazardous substances in non-bulk packagings.
172.325 Elevated temperature materials.
172.326 Portable tanks.
172.328 Cargo tanks.
172.330 Tank cars and multi-unit tank car tanks.
172.331 Bulk packagings other than portable tanks, cargo tanks, tank
cars and multi-unit tank car tanks.
172.332 Identification number markings.
172.334 Identification numbers; prohibited display.
172.336 Identification numbers; special provisions.
172.338 Replacement of identification numbers.
Subpart E--Labeling
172.400 General labeling requirements.
172.400a Exceptions from labeling.
172.401 Prohibited labeling.
172.402 Additional labeling requirements.
172.403 Class 7 (radioactive) material.
172.404 Labels for mixed and consolidated packaging.
172.405 Authorized label modifications.
172.406 Placement of labels.
172.407 Label specifications.
172.411 EXPLOSIVE 1.1, 1.2, 1.3, 1.4, 1.5 and 1.6 labels.
172.415 NON-FLAMMABLE GAS label.
172.416 POISON GAS label.
172.417 FLAMMABLE GAS label.
172.419 FLAMMABLE LIQUID label.
172.420 FLAMMABLE SOLID label.
172.422 SPONTANEOUSLY COMBUSTIBLE label.
[[Page 98]]
172.423 DANGEROUS WHEN WET label.
172.426 OXIDIZER label.
172.427 ORGANIC PEROXIDE label.
172.429 POISON INHALATION HAZARD label.
172.430 POISON label.
172.431 [Reserved]
172.432 INFECTIOUS SUBSTANCE label.
172.436 RADIOACTIVE WHITE-I label.
172.438 RADIOACTIVE YELLOW-II label.
172.440 RADIOACTIVE YELLOW-III label.
172.442 CORROSIVE label.
172.444 [Reserved]
172.446 CLASS 9 label.
172.448 CARGO AIRCRAFT ONLY label.
172.450 EMPTY label.
Subpart F--Placarding
172.500 Applicability of placarding requirements.
172.502 Prohibited and permissive placarding.
172.503 Identification number display on placards.
172.504 General placarding requirements.
172.505 Placarding for subsidiary hazards.
172.506 Providing and affixing placards: Highway.
172.507 Special placarding provisions: Highway.
172.508 Placarding and affixing placarding: Rail.
172.510 Special placarding provisions: Rail.
172.512 Freight containers and aircraft unit load devices.
172.514 Bulk packagings.
172.516 Visibility and display of placards.
172.519 General specifications for placards.
172.521 DANGEROUS placard.
172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.
172.523 EXPLOSIVES 1.4 placard.
172.524 EXPLOSIVES 1.5 placard.
172.525 EXPLOSIVES 1.6 placard.
172.526 [Reserved]
172.527 Background requirements for certain placards.
172.528 NON-FLAMMABLE GAS placard.
172.530 OXYGEN placard.
172.532 FLAMMABLE GAS placard.
172.536 [Reserved]
172.540 POISON GAS placard.
172.542 FLAMMABLE placard.
172.544 COMBUSTIBLE placard.
172.546 FLAMMABLE SOLID placard.
172.547 SPONTANEOUSLY COMBUSTIBLE placard.
172.548 DANGEROUS WHEN WET placard.
172.550 OXIDIZER placard.
172.552 ORGANIC PEROXIDE placard.
172.553 [Reserved]
172.554 POISON placard.
172.555 POISON INHALATION HAZARD placard.
172.556 RADIOACTIVE placard.
172.558 CORROSIVE placard.
172.560 CLASS 9 placard.
Subpart G--Emergency Response Information
172.600 Applicability and general requirements.
172.602 Emergency response information.
172.604 Emergency response telephone number.
172.606 Carrier information contact.
Subpart H--Training
172.700 Purpose and scope.
172.701 Federal-State relationship.
172.702 Applicability and responsibility for training and testing.
172.704 Training requirements.
Appendix A to Part 172--Office of Hazardous Materials Transportation
Color Tolerance Charts and Tables
Appendix B to Part 172--Trefoil Symbol
Appendix C to Part 172--Dimensional Specifications for Recommended
Placard Holder
Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.
Source: Amdt. 172-29, 41 FR 15996, Apr. 15, 1976, unless otherwise
noted.
Subpart A--General
Sec. 172.1 Purpose and scope.
This part lists and classifies those materials which the Department
has designated as hazardous materials for purposes of transportation and
prescribes the requirements for shipping papers, package marking,
labeling, and transport vehicle placarding applicable to the shipment
and transportation of those hazardous materials.
[Amdt. 172-29, 41 FR 15997, Apr. 15, 1976, as amended by 66 FR 45379,
Aug. 28, 2001]
Sec. 172.3 Applicability.
(a) This part applies to--
(1) Each person who offers a hazardous material for transportation,
and
(2) Each carrier by air, highway, rail, or water who transports a
hazardous material.
(b) When a person, other than one of those provided for in paragraph
(a) of this section, performs a packaging labeling or marking function
required by this part, that person shall perform the function in
accordance with this part.
[Amdt. 172-29, 41 FR 15996, Apr. 15, 1976, as amended by Amdt. 172-32,
41 FR 38179, Sept. 9, 1976]
[[Page 99]]
Subpart B--Table of Hazardous Materials and Special Provisions
Sec. 172.101 Purpose and use of hazardous materials table.
(a) The Hazardous Materials Table (Table) in this section designates
the materials listed therein as hazardous materials for the purpose of
transportation of those materials. For each listed material, the Table
identifies the hazard class or specifies that the material is forbidden
in transportation, and gives the proper shipping name or directs the
user to the preferred proper shipping name. In addition, the Table
specifies or references requirements in this subchapter pertaining to
labeling, packaging, quantity limits aboard aircraft and stowage of
hazardous materials aboard vessels.
(b) Column 1: Symbols. Column 1 of the Table contains six symbols
(``+'', ``A'', ``D'', ``G'', ``I'' and ``W'') as follows:
(1) The plus (+) sign fixes the proper shipping name, hazard class
and packing group for that entry without regard to whether the material
meets the definition of that class, packing group or any other hazard
class definition. When the plus sign is assigned to a proper shipping
name in Column (1) of the Sec. 172.101 Table, it means that the material
is known to pose a risk to humans. When a plus sign is assigned to
mixtures or solutions containing a material where the hazard to humans
is significantly different from that of the pure material or where no
hazard to humans is posed, the material may be described using an
alternative shipping name that represents the hazards posed by the
material. An appropriate alternate proper shipping name and hazard class
may be authorized by the Associate Administrator.
(2) The letter ``A'' denotes a material that is subject to the
requirements of this subchapter only when offered or intended for
transportation by aircraft, unless the material is a hazardous substance
or a hazardous waste. A shipping description entry preceded by an ``A''
may be used to describe a material for other modes of transportation
provided all applicable requirements for the entry are met.
(3) The letter ``D'' identifies proper shipping names which are
appropriate for describing materials for domestic transportation but may
be inappropriate for international transportation under the provisions
of international regulations (e.g., IMO, ICAO). An alternate proper
shipping name may be selected when either domestic or international
transportation is involved.
(4) The letter ``G'' identifies proper shipping names for which one
or more technical names of the hazardous material must be entered in
parentheses, in association with the basic description. (See
Sec. 172.203(k).)
(5) The letter ``I'' identifies proper shipping names which are
appropriate for describing materials in international transportation. An
alternate proper shipping name may be selected when only domestic
transportation is involved.
(6) The letter ``W'' denotes a material that is subject to the
requirements of this subchapter only when offered or intended for
transportation by vessel, unless the material is a hazardous substance
or a hazardous waste. A shipping description entry preceded by a ``W''
may be used to describe a material for other modes of transportation
provided all applicable requirements for the entry are met.
(c) Column 2: Hazardous materials descriptions and proper shipping
names. Column 2 lists the hazardous materials descriptions and proper
shipping names of materials designated as hazardous materials.
Modification of a proper shipping name may otherwise be required or
authorized by this section. Proper shipping names are limited to those
shown in Roman type (not italics).
(1) Proper shipping names may be used in the singular or plural and
in either capital or lower case letters. Words may be alternatively
spelled in the same manner as they appear in the ICAO Technical
Instructions or the IMDG Code. For example ``aluminum'' may be spelled
``aluminium'' and ``sulfur'' may be spelled ``sulphur''. However, the
word ``inflammable'' may not be used in place of the word ``flammable''.
(2) Punctuation marks and words in italics are not part of the
proper shipping name, but may be used in addition to the proper shipping
name. The word
[[Page 100]]
``or'' in italics indicates that terms in the sequence may be used as
the proper shipping name, as appropriate.
(3) The word ``poison'' or ``poisonous'' may be used interchangeably
with the word ``toxic'' when only domestic transportation is involved.
The abbreviation ``n.o.i.'' or ``n.o.i.b.n.'' may be used
interchangeably with ``n.o.s.''.
(4) Except for hazardous wastes, when qualifying words are used as
part of the proper shipping name, their sequence in the package markings
and shipping paper description is optional. However, the entry in the
Table reflects the preferred sequence.
(5) When one entry references another entry by use of the word
``see'', if both names are in Roman type, either name may be used as the
proper shipping name (e.g., Ethyl alcohol, see Ethanol).
(6) When a proper shipping name includes a concentration range as
part of the shipping description, the actual concentration, if it is
within the range stated, may be used in place of the concentration
range. For example, an aqueous solution of hydrogen peroxide containing
30 percent peroxide may be described as ``Hydrogen peroxide, aqueous
solution with not less than 20 percent but not more than 40 percent
hydrogen peroxide'' or ``Hydrogen peroxide, aqueous solution with 30
percent hydrogen peroxide''.
(7) Use of the prefix ``mono'' is optional in any shipping name,
when appropriate. Thus, Iodine monochloride may be used interchangeably
with Iodine chloride. In ``Glycerol alpha-monochlorohydrin'' the term
``mono'' is considered a prefix to the term ``chlorohydrin'' and may be
deleted.
(8) Use of the word ``liquid'' or ``solid''. The word ``liquid'' or
``solid'' may be added to a proper shipping name when a hazardous
material specifically listed by name may, due to differing physical
states, be a liquid or solid. When the packaging specified in Column 8
is inappropriate for the physical state of the material, the table
provided in paragraph (i)(4) of this section should be used to determine
the appropriate packaging section.
(9) Hazardous wastes. If the word ``waste'' is not included in the
hazardous material description in Column 2 of the Table, the proper
shipping name for a hazardous waste (as defined in Sec. 171.8 of this
subchapter), shall include the word ``Waste'' preceding the proper
shipping name of the material. For example: Waste acetone.
(10) Mixtures and solutions. (i) A mixture or solution not
identified specifically by name, comprised of a hazardous material
identified in the Table by technical name and non-hazardous material,
shall be described using the proper shipping name of the hazardous
material and the qualifying word ``mixture'' or ``solution'', as
appropriate, unless--
(A) Except as provided in Sec. 172.101(i)(4) the packaging specified
in Column 8 is inappropriate to the physical state of the material;
(B) The shipping description indicates that the proper shipping name
applies only to the pure or technically pure hazardous material;
(C) The hazard class, packing group, or subsidiary hazard of the
mixture or solution is different from that specified for the entry;
(D) There is a significant change in the measures to be taken in
emergencies;
(E) The material is identified by special provision in Column 7 of
the Sec. 172.101 Table as a material poisonous by inhalation; however,
it no longer meets the definition of poisonous by inhalation or it falls
within a different hazard zone than that specified in the special
provision; or
(F) The material can be appropriately described by a shipping name
that describes its intended application, such as ``Coating solution'',
``Extracts, flavoring'' or ``Compound, cleaning liquid''.
(ii) If one or more of the conditions specified in paragraph
(c)(10)(i) of this section is satisfied, then a proper shipping name
shall be selected as prescribed in paragraph (c)(12)(ii) of this
section.
(iii) A mixture or solution not identified in the Table specifically
by name, comprised of two or more hazardous materials in the same hazard
class, shall be described using an appropriate shipping description
(e.g., ``Flammable liquid, n.o.s.''). The name that most appropriately
describes the material
[[Page 101]]
shall be used; e.g., an alcohol not listed by its technical name in the
Table shall be described as ``Alcohol, n.o.s.'' rather than ``Flammable
liquid, n.o.s.''. Some mixtures may be more appropriately described
according to their application, such as ``Coating solution'' or
``Extracts, flavoring liquid'' rather than by an n.o.s. entry. Under the
provisions of subparts C and D of this part, the technical names of at
least two components most predominately contributing to the hazards of
the mixture or solution may be required in association with the proper
shipping name.
(11) Except for a material subject to or prohibited by Secs. 173.21,
173.54, 173.56(d), 173.56(e), 173.224(c) or 173.225(c) of this
subchapter, a material that is considered to be a hazardous waste or a
sample of a material for which the hazard class is uncertain and must be
determined by testing may be assigned a tentative proper shipping name,
hazard class, identification number and packing group, if applicable,
based on the shipper's tentative determination according to:
(i) Defining criteria in this subchapter;
(ii) The hazard precedence prescribed in Sec. 173.2a of this
subchapter;
(iii) The shippers knowledge of the material;
(iv) In addition to paragraphs (c)(11)(i) through (iii) of this
section, for a sample of a material, other than a waste, the following
must be met:
(A) Except when the word ``Sample'' already appears in the proper
shipping name, the word ``Sample'' must appear in association with the
basic description of a sample on the shipping paper;
(B) When the proper shipping description for a sample is assigned a
``G'' in Column (1) of the Sec. 172.101 Table, and the primary
constituent(s) for which the tentative classification is based are not
known, the provisions requiring a technical name for the constituent(s)
do not apply; and
(C) A sample must be transported in a combination packaging which
conforms to the requirements of this subchapter that are applicable to
the tentative packing group assigned, and may not exceed a net mass of
2.5 kg. (5.5 pounds) per package.
Note to Paragraph (c)(11): For the transportation of self-reactive,
organic peroxide and explosive samples, see Secs. 173.224(c)(3),
173.225(c)(2) and 173.56(d) of this subchapter, respectively.
(12) Except when the proper shipping name in the Table is preceded
by a plus (+)--
(i) If it is specifically determined that a material meets the
definition of a hazard class, packing group or hazard zone, other than
the class, packing group or hazard zone shown in association with the
proper shipping name, or does not meet the defining criteria for a
subsidiary hazard shown in Column 6 of the Table, the material shall be
described by an appropriate proper shipping name listed in association
with the correct hazard class, packing group, hazard zone, or subsidiary
hazard for the material.
(ii) Generic or n.o.s. descriptions. If an appropriate technical
name is not shown in the Table, selection of a proper shipping name
shall be made from the generic or n.o.s. descriptions corresponding to
the specific hazard class, packing group, hazard zone, or subsidiary
hazard, if any, for the material. The name that most appropriately
describes the material shall be used; e.g., an alcohol not listed by its
technical name in the Table shall be described as ``Alcohol, n.o.s.''
rather than ``Flammable liquid, n.o.s.''. Some mixtures may be more
appropriately described according to their application, such as
``Coating solution'' or ``Extracts, flavoring, liquid'', rather than by
an n.o.s. entry, such as ``Flammable liquid, n.o.s.'' It should be
noted, however, that an n.o.s. description as a proper shipping name may
not provide sufficient information for shipping papers and package
markings. Under the provisions of subparts C and D of this part, the
technical name of one or more constituents which makes the product a
hazardous material may be required in association with the proper
shipping name.
(iii) Multiple hazard materials. If a material meets the definition
of more than one hazard class, and is not identified in the Table
specifically by name (e.g., acetyl chloride), the hazard class of the
material shall be determined by using the precedence specified in
[[Page 102]]
Sec. 173.2a of this subchapter, and an appropriate shipping description
(e.g., ``Flammable liquid, corrosive n.o.s.'') shall be selected as
described in paragraph (c)(12)(ii) of this section.
(iv) If it is specifically determined that a material is not a
forbidden material and does not meet the definition of any hazard class,
the material is not a hazardous material.
(13) Self-reactive materials and organic peroxides. A generic proper
shipping name for a self-reactive material or an organic peroxide, as
listed in Column 2 of the Table, must be selected based on the
material's technical name and concentration, in accordance with the
provisions of Secs. 173.224 or 173.225 of this subchapter, respectively.
(14) A proper shipping name that describes all isomers of a material
may be used to identify any isomer of that material if the isomer meets
criteria for the same hazard class or division, subsidiary risk(s) and
packing group, unless the isomer is specifically identified in the
Table.
(15) Hydrates of inorganic substances may be identified using the
proper shipping name for the equivalent anhydrous substance if the
hydrate meets the same hazard class or division, subsidiary risk(s) and
packing group, unless the hydrate is specifically identified in the
Table.
(16) Unless it is already included in the proper shipping name in
the Sec. 172.101 Table, the qualifying words ``liquid'' or ``solid'' may
be added in association with the proper shipping name when a hazardous
material specifically listed by name in the Sec. 172.101 Table may, due
to the differing physical states of the various isomers of the material,
be either a liquid or a solid (for example ``Dinitrotoluenes, liquid''
and ``Dinitrotoluenes, solid''). Use of the words ``liquid'' or
``solid'' is subject to the limitations specified for the use of the
words ``mixture'' or ``solution'' in paragraph (c)(10) of this section.
The qualifying word ``molten'' may be added in association with the
proper shipping name when a hazardous material, which is a solid in
accordance with the definition in Sec. 171.8 of this subchapter, is
offered for transportation in the molten state (for example,
``Alkylphenols, solid, n.o.s., molten'').
(d) Column 3: Hazard class or Division. Column 3 contains a
designation of the hazard class or division corresponding to each proper
shipping name, or the word ``Forbidden''.
(1) A material for which the entry in this column is ``Forbidden''
may not be offered for transportation or transported. This prohibition
does not apply if the material is diluted, stabilized or incorporated in
a device and it is classed in accordance with the definitions of
hazardous materials contained in part 173 of this subchapter.
(2) When a reevaluation of test data or new data indicates a need to
modify the ``Forbidden'' designation or the hazard class or packing
group specified for a material specifically identified in the Table,
this data should be submitted to the Associate Administrator.
(3) A basic description of each hazard class and the section
reference for class definitions appear in Sec. 173.2 of this subchapter.
(4) Each reference to a Class 3 material is modified to read
``Combustible liquid'' when that material is reclassified in accordance
with Sec. 173.150 (e) or (f) of this subchapter or has a flash point
above 60.5 deg.C (141 deg.F) but below 93 deg.C (200 deg.F).
(e) Column 4: Identification number. Column 4 lists the
identification number assigned to each proper shipping name. Those
preceded by the letters ``UN'' are associated with proper shipping names
considered appropriate for international transportation as well as
domestic transportation. Those preceded by the letters ``NA'' are
associated with proper shipping names not recognized for international
transportation, except to and from Canada. Identification numbers in the
``NA9000'' series are associated with proper shipping names not
appropriately covered by international hazardous materials (dangerous
goods) transportation standards, or not appropriately addressed by
international transportation standards for emergency response
information purposes, except for transportation between the United
States and Canada.
(f) Column 5: Packing group. Column 5 specifies one or more packing
groups assigned to a material corresponding to the proper shipping name
and hazard
[[Page 103]]
class for that material. Class 2, Class 7, Division 6.2 (other than
regulated medical wastes), and ORM-D materials, do not have packing
groups. Packing Groups I, II and III indicate the degree of danger
presented by the material is either great, medium or minor,
respectively. If more than one packing group is indicated for an entry,
the packing group for the hazardous material is determined using the
criteria for assignment of packing groups specified in subpart D of part
173. When a reevaluation of test data or new data indicates a need to
modify the specified packing group(s), the data should be submitted to
the Associate Administrator. Each reference in this column to a material
which is a hazardous waste or a hazardous substance, and whose proper
shipping name is preceded in Column 1 of the Table by the letter ``A''
or ``W'', is modified to read ``III'' on those occasions when the
material is offered for transportation or transported by a mode in which
its transportation is not otherwise subject to requirements of this
subchapter.
(g) Column 6: Labels. Column 6 specifies codes which represent the
hazard warning labels required for a package filled with a material
conforming to the associated hazard class and proper shipping name,
unless the package is otherwise excepted from labeling by a provision in
subpart E of this part, or part 173 of this subchapter. The first code
is indicative of the primary hazard of the material. Additional label
codes are indicative of subsidiary hazards. Provisions in Sec. 172.402
may require that a label other than that specified in Column 6 be
affixed to the package in addition to that specified in Column 6. No
label is required for a material classed as a combustible liquid or for
a Class 3 material that is reclassed as a combustible liquid. For
``Empty'' label requirements, see Sec. 173.428 of this subchapter. The
codes contained in Column 6 are defined according to the following
table:
Label Substitution Table
------------------------------------------------------------------------
Label code Label name
------------------------------------------------------------------------
1......................................... Explosive
1.1 \1\................................... Explosive 1.1\1\
1.2 \1\................................... Explosive 1.2\1\
1.3 \1\................................... Explosive 1.3\1\
1.4 \1\................................... Explosive 1.4\1\
1.5 \1\................................... Explosive 1.5\1\
1.6 \1\................................... Explosive 1.6\1\
2.1....................................... Flammable Gas
2.2....................................... Non-Flammable Gas
2.3....................................... Poison Gas
3......................................... Flammable Liquid
4.1....................................... Flammable Solid
4.2....................................... Spontaneously Combustible
4.3....................................... Dangerous When Wet
5.1....................................... Oxidizer
5.2....................................... Organic Peroxide
6.1 (inhalation hazard, Zone A or B)...... Poison Inhalation Hazard
6.1 (other than inhalation hazard, Zone A Poison
or B) \2\.
6.2....................................... Infectious substance
7......................................... Radioactive
8......................................... Corrosive
9......................................... Class 9
------------------------------------------------------------------------
\1\ Refers to the appropriate compatibility group letter.
\2\ The packing group for a material is indicated in column 5 of the
table.
(h) Column 7: Special provisions. Column 7 specifies codes for
special provisions applicable to hazardous materials. When Column 7
refers to a special provision for a hazardous material, the meaning and
requirements of that special provision are as set forth in Sec. 172.102
of this subpart.
(i) Column 8: Packaging authorizations. Columns 8A, 8B and 8C
specify the applicable sections for exceptions, non-bulk packaging
requirements and bulk packaging requirements, respectively, in part 173
of this subchapter. Columns 8A, 8B and 8C are completed in a manner
which indicates that ``Sec. 173.'' precedes the designated numerical
entry. For example, the entry ``202'' in Column 8B associated with the
proper shipping name ``Gasoline'' indicates that for this material
conformance to non-bulk packaging requirements prescribed in
Sec. 173.202 of this subchapter is required. When packaging requirements
are specified, they are in addition to the standard requirements for all
packagings prescribed in Sec. 173.24 of this subchapter and any other
applicable requirements in subparts A and B of part 173 of this
subchapter.
(1) Exceptions. Column 8A contains exceptions from some of the
requirements of this subchapter. The referenced exceptions are in
addition to those specified in subpart A of part 173 and elsewhere in
this subchapter. A ``None'' in this column means no packaging exceptions
are authorized, except
[[Page 104]]
as may be provided by special provisions in Column 7.
(2) Non-bulk packaging. Column 8B references the section in part 173
of this subchapter which prescribes packaging requirements for non-bulk
packagings. A ``None'' in this column means non-bulk packagings are not
authorized, except as may be provided by special provisions in Column 7.
Each reference in this column to a material which is a hazardous waste
or a hazardous substance, and whose proper shipping name is preceded in
Column 1 of the Table by the letter ``A'' or ``W'', is modified to
include ``Sec. 173.203'' or ``Sec. 173.213'', as appropriate for liquids
and solids, respectively, on those occasions when the material is
offered for transportation or transported by a mode in which its
transportation is not otherwise subject to the requirements of this
subchapter.
(3) Bulk packaging. Column 8C specifies the section in part 173 of
this subchapter which prescribes packaging requirements for bulk
packagings, subject to the limitations, requirements and additional
authorizations of Column 7. A ``None'' in this column means bulk
packagings are not authorized, except as may be provided by special
provisions in Column 7. Additional authorizations and limitations for
use of IM portable tanks are set forth in Column 7. For each reference
in this column to a material which is a hazardous waste or a hazardous
substance, and whose proper shipping name is preceded in Column 1 of the
Table by the letter ``A'' or ``W'' and which is offered for
transportation or transported by a mode in which its transportation is
not otherwise subject to the requirements of this subchapter:
(i) The column reference is Sec. 173.240 or Sec. 173.241, as
appropriate.
(ii) For a solid material, the exception provided in Special
provision B54 is applicable.
(iii) For a Class 9 material which meets the definition of an
elevated temperature material, the column reference is Sec. 173.247.
(4) For a hazardous material which is specifically named in the
Table and whose packaging sections specify packagings not applicable to
the form of the material (e.g., packaging specified is for solid
material and the material is being offered for transportation in a
liquid form) the following table should be used to determine the
appropriate packaging section:
------------------------------------------------------------------------
Corresponding packaging
Packaging section reference for solid materials section for liquid
materials
------------------------------------------------------------------------
Sec. 173.187.................................. Sec. 173.181
Sec. 173.211.................................. Sec. 173.201
Sec. 173.212.................................. Sec. 173.202
Sec. 173.213.................................. Sec. 173.203
Sec. 173.240.................................. Sec. 173.241
Sec. 173.242.................................. Sec. 173.243
------------------------------------------------------------------------
(j) Column 9: Quantity limitations. Columns 9A and 9B specify the
maximum quantities that may be offered for transportation in one package
by passenger-carrying aircraft or passenger-carrying rail car (Column
9A) or by cargo aircraft only (Column 9B), subject to the following:
(1) ``Forbidden'' means the material may not be offered for
transportation or transported in the applicable mode of transport.
(2) The quantity limitation is ``net'' except where otherwise
specified, such as for ``Consumer commodity'' which specifies ``30 kg
gross.''
(3) When articles or devices are specifically listed by name, the
net quantity limitation applies to the entire article or device (less
packaging and packaging materials) rather than only to its hazardous
components.
(4) A package offered or intended for transportation by aircraft and
which is filled with a material forbidden on passenger-carrying aircraft
but permitted on cargo aircraft only, or which exceeds the maximum net
quantity authorized on passenger-carrying aircraft, shall be labelled
with the CARGO AIRCRAFT ONLY label specified in Sec. 172.448 of this
part.
(k) Column 10: Vessel stowage requirements. Column 10A [Vessel
stowage] specifies the authorized stowage locations on board cargo and
passenger vessels. Column 10B [Other provisions] specifies codes for
stowage requirements for specific hazardous materials. The meaning of
each code in Column 10B is set forth in Sec. 176.84 of this subchapter.
Section 176.63 of this subchapter sets forth the physical requirements
for each of the authorized locations listed in Column 10A. (For bulk
[[Page 105]]
transportation by vessel, see 46 CFR parts 30 to 40, 70, 98, 148, 151,
153 and 154.) The authorized stowage locations specified in Column 10A
are defined as follows:
(1) Stowage category ``A'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel and on a passenger vessel.
(2) Stowage category ``B'' means--
(i) The material may be stowed ``on deck'' or ``under deck'' on a
cargo vessel and on a passenger vessel carrying a number of passengers
limited to not more than the larger of 25 passengers, or one passenger
per each 3 m of overall vessel length; and
(ii) ``On deck only'' on passenger vessels in which the number of
passengers specified in paragraph (k)(2)(i) of this section is exceeded.
(3) Stowage category ``C'' means the material must be stowed ``on
deck only'' on a cargo vessel and on a passenger vessel.
(4) Stowage category ``D'' means the material must be stowed ``on
deck only'' on a cargo vessel and on a passenger vessel carrying a
number of passengers limited to not more than the larger of 25
passengers or one passenger per each 3 m of overall vessel length, but
the material is prohibited on passenger vessels in which the limiting
number of passengers is exceeded.
(5) Stowage category ``E'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel and on a passenger vessel
carrying a number of passengers limited to not more than the larger of
25 passengers, or one passenger per each 3 m of overall vessel length,
but is prohibited from carriage on passenger vessels in which the
limiting number of passengers is exceeded.
(6) Stowage category ``01'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and on
a passenger vessel.
(7) Stowage category ``02'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and
``on deck'' in closed cargo transport units or ``under deck'' in closed
cargo transport units on a passenger vessel.
(8) Stowage category ``03'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and
``on deck'' in closed cargo transport units on a passenger vessel.
(9) Stowage category ``04'' means the material may be stowed ``on
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) but the
material is prohibited on a passenger vessel.
(10) Stowage category ``05'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' on a cargo
vessel (up to 12 passengers) and on a passenger vessel.
(11) Stowage category ``06'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' on a cargo
vessel (up to 12 passengers) and ``on deck'' in closed cargo transport
units or ``under deck'' in closed cargo transport units on a passenger
vessel.
(12) Stowage category ``07'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' on a cargo
vessel (up to 12 passengers) and ``on deck'' only in closed cargo
transport units on a passenger vessel.
(13) Stowage category ``08'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' on a cargo
vessel (up to 12 passengers) but the material is prohibited on a
passenger vessel.
(14) Stowage category ``09'' means the material may be stowed ``on
deck only'' in closed cargo transport units or ``under deck'' in closed
cargo transport units on a cargo vessel (up to 12 passengers) and on a
passenger vessel.
(15) Stowage category ``10'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' in closed cargo
transport units on a cargo vessel (up to 12 passengers) and ``on deck''
only in closed cargo transport units on a passenger vessel.
(16) Stowage category ``11'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' in magazine
stowage type ``c'' on a cargo vessel (up to 12 passengers) and ``on
deck'' only in closed cargo transport units on a passenger vessel.
(17) Stowage category ``12'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' in magazine
stowage type ``c'' on
[[Page 106]]
a cargo vessel (up to 12 passengers) but the material is prohibited on a
passenger vessel.
(18) Stowage category ``13'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' in magazine
stowage type ``A'' on a cargo vessel (up to 12 passengers) and ``on
deck'' only in closed cargo transport units on a passenger vessel.
(19) Stowage category ``14'' means the material may be stowed ``on
deck'' in closed cargo transport units on a cargo vessel (up to 12
passengers) but the material is prohibited on a passenger vessel.
(20) Stowage category ``15'' means the material may be stowed ``on
deck'' in closed cargo transport units or ``under deck'' in closed cargo
transport units on a cargo vessel (up to 12 passengers) but the material
is prohibited on a passenger vessel.
(l) Changes to the Table. (1) Unless specifically stated otherwise
in a rule document published in the Federal Register amending the
Table--
(i) Such a change does not apply to the shipment of any package
filled prior to the effective date of the amendment; and
(ii) Stocks of preprinted shipping papers and package markings may
be continued in use, in the manner previously authorized, until depleted
or for a one-year period, subsequent to the effective date of the
amendment, whichever is less.
(2) Except as otherwise provided in this section, any alteration of
a shipping description or associated entry which is listed in the
Sec. 172.101 Table must receive prior written approval from the
Associate Administrator.
(3) The proper shipping name of a hazardous material changed in the
May 6, 1997 final rule, in effect on October 1, 1997, only by the
addition or omission of the word ``compressed,'' ``inhibited,''
``liquefied'' or ``solution'' may continue to be used to comply with
package marking requirements, until January 1, 2003.
[[Page 107]]
Sec. 172.101 Hazardous Materials Table
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
(8) Packaging (9) (10) Vessel
Hazardous materials (Sec. 173.***) Quantity limitations stowage
descriptions and Hazard Identification Label Special ------------------------------------------------------------------------------------------
Symbols proper shipping class or Numbers PG Codes provisions (Sec. Passenger
names Division 172.102) Exceptions Non-bulk Bulk aircraft/ Cargo air- Location Other
rail craft only
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
(1) (2)................. (3) (4) (5) (6)....... (7) (8A).......... (8B)....... (8C)....... (9A) (9B) (10A) (10B)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Accellerene, see p- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Nitrosodimethylanil
ine.
Accumulators, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
electric, see
Batteries, wet etc.
Acetal.............. 3 UN1088 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
Acetaldehyde........ 3 UN1089 I 3......... A3, B16, T11, None.......... 201........ 243........ Forbidden 30 L E .......
TP2, TP7
A Acetaldehyde ammonia 9 UN1841 III 9......... IB8, IP6 155........... 204........ 240........ 200 kg 200 kg A 34
Acetaldehyde oxime.. 3 UN2332 III 3......... B1, IB3, T4, TP1 150........... 203........ 242........ 60 L 220 L A .......
Acetic acid, glacial 8 UN2789 II 8, 3...... A3, A6, A7, A10, 154........... 202........ 243........ 1 L 30 L A .......
or Acetic acid B2, IB2, T7, TP2
solution, with more
than 80 percent
acid, by mass.
Acetic acid 8 UN2790 II 8......... A3, A6, A7, A10, 154........... 202........ 242........ 1 L 30 L A .......
solution, not less B2, IB2, T7, TP2
than 50 percent but
not more than 80
percent acid, by
mass.
Acetic acid 8 UN2790 III 8......... IB3, T4, TP1 154........... 203........ 242........ 5 L 60 L A .......
solution, with more
than 10 percent and
less than 50
percent acid, by
mass.
Acetic anhydride.... 8 UN1715 II 8, 3...... A3, A6, A7, A10, 154........... 202........ 243........ 1 L 30 L A 40
B2, IB2, T7, TP2
Acetone............. 3 UN1090 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Acetone cyanohydrin, 6.1 UN1541 I 6.1....... 2, A3, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 25, 40,
stabilized. B32, B76, B77, 49
N34, T20, TP2,
TP13, TP38, TP45
Acetone oils........ 3 UN1091 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8
Acetonitrile........ 3 UN1648 II 3......... IB2, T7, TP2 150........... 202........ 242........ 5L 60 L B 40
Acetyl acetone Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide with more
than 9 percent by
mass active oxygen.
Acetyl benzoyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide, solid, or
with more than 40
percent in solution.
Acetyl bromide...... 8 UN1716 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L C 40
TP2, TP12
[[Page 108]]
Acetyl chloride..... 3 UN1717 II 3, 8...... A3, A6, A7, IB1, None.......... 202........ 243........ 1 L 5 L B 40
N34, T8, TP2,
TP12
Acetyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
cyclohexanesulfonyl
peroxide, with more
than 82 percent
wetted with less
than 12 percent
water.
Acetyl iodide....... 8 UN1898 II 8......... B2, IB2, T7, 154........... 202........ 242........ 1 L 30 L C 40
TP2, TP13
Acetyl methyl 3 UN2621 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
carbinol.
Acetyl peroxide, Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, or with more
than 25 percent in
solution.
Acetylene, dissolved 2.1 UN1001 ....... 2.1....... None.......... 303........ None....... Forbidden 15 kg D 25, 40,
57
Acetylene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(liquefied).
Acetylene silver Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrate.
Acetylene ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
tetrabromide, see
Tetrabromoethane.
Acid butyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
phosphate, see
Butyl acid
phosphate.
Acid, sludge, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Sludge acid.
Acridine............ 6.1 UN2713 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Acrolein dimer, 3 UN2607 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A 40
stabilized.
Acrolein, stabilized 6.1 UN1092 I 6.1, 3.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
B42, B72, B77,
T22, TP2, TP7,
TP13, TP38, TP44
Acrylamide.......... 6.1 UN2074 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A 12
TP1
Acrylic acid, 8 UN2218 II 8, 3...... B2, IB2, T7, TP2 154........... 202........ 243........ 1 L 30 L C 25, 40
stabilized.
Acrylonitrile, 3 UN1093 I 3, 6.1.... B9, T14, TP2, None.......... 201........ 243........ Forbidden 30 L E 40
stabilized. TP13
Actuating cartridge, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
explosive, see
Cartridges, power
device.
Adhesives, 3 UN1133 I 3......... B42, T11, TP1, 150........... 201........ 243........ 1 L 30 L B .......
containing a TP8, TP27
flammable liquid.
.................... ........... .................. II 3......... B52, IB2, T4, 150........... 173........ 242........ 5 L 60 L B .......
TP1, TP8
[[Page 109]]
.................... ........... .................. III 3......... B1, B52, IB3, 150........... 173........ 242........ 60 L 220 L A .......
T2, TP1
Adiponitrile........ 6.1 UN2205 III 6.1....... IB3, T3, TP1 153........... 203........ 241........ 60 L 220 L A .......
Aerosols, corrosive, 2.2 UN1950 ....... 2.2, 8.... A34 306........... None....... None....... 75 kg 150 kg A 40, 48,
Packing Group II or 85
III, (each not
exceeding 1 L
capacity).
Aerosols, flammable, 2.1 UN1950 ....... 2.1....... N82 306........... None....... None....... 75 kg 150 kg A 40, 48,
(each not exceeding 85
1 L capacity).
Aerosols, flammable, 2.1 UN1950 ....... 2.1....... N82 306........... None....... None....... Forbidden 150 kg A 40, 48,
n.o.s. (engine 85
starting fluid)
(each not exceeding
1 L capacity).
Aerosols, non- 2.2 UN1950 ....... 2.2....... 306, 307...... None....... None....... 75 kg 150 kg A 48, 85
flammable, (each
not exceeding 1 L
capacity).
Aerosols, poison, 2.2 UN1950 ....... 2.2....... 306........... None....... None....... Forbidden Forbidden A 40, 48,
each not exceeding 85
1 L capacity.
Air bag inflators, 2.2 UN3353 ....... 2.2....... 133 166........... 166........ 166........ 75 kg 150 kg A .......
compressed gas or
Air bag modules,
compressed gas or
Seat-belt
pretensioners,
compressed gas.
Air bag inflators, 1.4G UN0503 II 1.4G...... 166........... 166........ 166........ Forbidden 75 kg 02 24E
pyrotechnic or Air
bag modules,
pyrotechnic or Seat-
belt pretensioner,
pyrotechnic.
Air bag inflators, 9 UN3268 III 9......... 166........... 166........ 166........ 25 kg 100 kg A .......
pyrotechnic or Air
bag modules,
pyrotechnic or Seat-
belt pretensioner,
pyrotechnic.
Air, compressed..... 2.2 UN1002 ....... 2.2....... 78 306........... 302........ 302........ 75 kg 150 kg A .......
Air, refrigerated 2.2 UN1003 ....... 2.2, 5.1.. T75, TP5, TP22 320........... 316........ 318, 319... Forbidden 150 kg D 51
liquid, (cryogenic
liquid).
Air, refrigerated 2.2 UN1003 ....... 2.2, 5.1.. T75, TP5, TP22 320........... 316........ 318, 319... Forbidden Forbidden D 51
liquid, (cryogenic
liquid) non-
pressurized.
Aircraft engines ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(including
turbines), see
Engines, internal
combustion.
Aircraft evacuation ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
slides, see Life
saving appliances
etc.
Aircraft hydraulic 3 UN3165 I 3, 6.1, 8. None.......... 172........ None....... Forbidden 42 L E .......
power unit fuel
tank (containing a
mixture of
anhydrous hydrazine
and monomethyl
hydrazine) (M86
fuel).
Aircraft survival ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
kits, see Life
saving appliances
etc.
G Alcoholates 3 UN3274 II 3, 8...... IB2 None.......... 202........ 243........ 1 L 5 L B .......
solution, n.o.s.,
in alcohol.
Alcoholic beverages. 3 UN3065 II 3......... 24, B1, IB2, T4, 150........... 202........ 242........ 5 L 60 L A .......
TP1
[[Page 110]]
.................... ........... .................. III 3......... 24, B1, IB3, 150........... 203........ 242........ 60 L 220 L A .......
N11, T2, TP1
Alcohols, n.o.s..... 3 UN1987 I 3......... T11, TP1, TP8, None.......... 201........ 243........ 1 L 30 L E .......
TP27
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
G Alcohols, flammable, 3 UN1986 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L E 40
toxic, n.o.s.. TP27
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP27
.................... ........... .................. III 3, 6.1.... B1, IB3, T7, None.......... 203........ 242........ 60 L 220 L A .......
TP1, TP28
Aldehydes, n.o.s.... 3 UN1989 I 3......... T11, TP1, TP27 None.......... 201........ 243........ 1 L 30 L E .......
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
G Aldehydes, 3 UN1988 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L E 40
flammable, toxic, TP27
n.o.s..
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP27
.................... ........... .................. III 3, 6.1.... B1, IB3, T7, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP28
Aldol............... 6.1 UN2839 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 12
G Alkali metal 4.2 UN3206 II 4.2, 8.... 64, IB5, IP2 None.......... 212........ 242........ 15 kg 50 kg B .......
alcoholates, self-
heating, corrosive,
n.o.s..
.................... ........... .................. III 4.2, 8.... 64, IB8, IP3 None.......... 213........ 242........ 25 kg 100 kg B .......
Alkali metal alloys, 4.3 UN1421 I 4.3....... A2, A3, B48, N34 None.......... 201........ 244........ Forbidden 1 L D .......
liquid, n.o.s..
Alkali metal 4.3 UN1389 I 4.3....... A2, A3, N34 None.......... 201........ 244........ Forbidden 1 L D 40
amalgam, liquid.
Alkali metal 4.3 UN1389 I 4.3....... IB4, IP1, N40 None.......... 211........ 242........ Forbidden 15 kg D .......
amalgam, solid.
Alkali metal amides. 4.3 UN1390 II 4.3....... A6, A7, A8, A19, 151........... 212........ 241........ 15 kg 50 kg E 40
A20, IB7, IP2
Alkali metal 4.3 UN1391 I 4.3....... A2, A3 None.......... 201........ 244........ Forbidden 1 L D .......
dispersions, or
Alkaline earth
metal dispersions.
[[Page 111]]
Alkaline corrosive ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
liquids, n.o.s.,
see Caustic alkali
liquids, n.o.s..
G Alkaline earth metal 4.2 UN3205 II 4.2....... 65, IB6, IP2 None.......... 212........ 241........ 15 kg 50 kg B .......
alcoholates, n.o.s..
.................... ........... .................. III 4.2....... 65, IB8, IP3 None.......... 213........ 241........ 25 kg 100 kg B .......
Alkaline earth metal 4.3 UN1393 II 4.3....... A19, IB7, IP2 151........... 212........ 241........ 15 kg 50 kg E .......
alloys, n.o.s..
Alkaline earth metal 4.3 UN1392 I 4.3....... A19, IB4, IP1, None.......... 211........ 242........ Forbidden 15 kg D .......
amalgams. N34, N40
G Alkaloids, liquid, 6.1 UN3140 I 6.1....... A4, T14, TP2, None.......... 201........ 243........ 1 L 30 L A .......
n.o.s., or Alkaloid TP27
salts, liquid,
n.o.s..
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L A .......
TP27
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A .......
TP28
G Alkaloids, solid, 6.1 UN1544 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A .......
n.o.s. or Alkaloid
salts, solid,
n.o.s. poisonous.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Alkyl sulfonic 8 UN2584 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L B .......
acids, liquid or TP2, TP12, TP13
Aryl sulfonic
acids, liquid with
more than 5 percent
free sulfuric acid.
Alkyl sulfonic 8 UN2586 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L B .......
acids, liquid or
Aryl sulfonic
acids, liquid with
not more than 5
percent free
sulfuric acid.
Alkyl sulfonic 8 UN2583 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
acids, solid or
Aryl sulfonic
acids, solid, with
more than 5 percent
free sulfuric acid.
Alkyl sulfonic 8 UN2585 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
acids, solid or
Aryl sulfonic
acids, solid with
not more than 5
percent free
sulfuric acid.
Alkylphenols, 8 UN3145 I 8......... T14, TP2 None.......... 201........ 243........ 0.5 L 2.5 L B .......
liquid, n.o.s.
(including C2-C12
homologues).
.................... ........... .................. II 8......... IB2, T11, TP2, 154........... 202........ 242........ 1 L 30 L B .......
TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A .......
TP28
Alkylphenols, solid, 8 UN2430 I 8......... IB7, IP1, T10, None.......... 211........ 242........ 1 kg 25 kg B .......
n.o.s. (including TP2, TP28
C2-C12 homologues).
.................... ........... .................. II 8......... IB8, IP2, IP4, 154........... 212........ 240........ 15 kg 50 kg B .......
T3, TP2
.................... ........... .................. III 8......... IB8, IP3, T3, 154........... 213........ 240........ 25 kg 100 kg A .......
TP1
Alkylsulfuric acids. 8 UN2571 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L C 14
TP2, TP12, TP13
[[Page 112]]
Allethrin, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Pesticides, liquid,
toxic, n.o.s..
Allyl acetate....... 3 UN2333 II 3, 6.1.... IB2, T7, TP1, None.......... 202........ 243........ 1 L 60 L E 40
TP13
Allyl alcohol....... 6.1 UN1098 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, B77, T20,
TP2, TP13, TP38,
TP45
Allyl bromide....... 3 UN1099 I 3, 6.1.... T14, TP2, TP13 None.......... 201........ 243........ Forbidden 30 L B 40
Allyl chloride...... 3 UN1100 I 3, 6.1.... T14, TP2, TP13 None.......... 201........ 243........ Forbidden 30 L E 40
Allyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chlorocarbonate,
see Allyl
chloroformate.
Allyl chloroformate. 6.1 UN1722 I 6.1, 3, 8. 2, A3, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
B32, B74, N41,
T20, TP2, TP13,
TP38, TP45
Allyl ethyl ether... 3 UN2335 II 3, 6.1.... IB2, T7, TP1, None.......... 202........ 243........ 1 L 60 L E 40
TP13
Allyl formate....... 3 UN2336 I 3, 6.1.... T14, TP2, TP13 None.......... 201........ 243........ Forbidden 30 L E 40
Allyl glycidyl ether 3 UN2219 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Allyl iodide........ 3 UN1723 II 3, 8...... A3, A6, IB1, None.......... 202........ 243........ 1 L 5 L B 40
N34, T7, TP2,
TP13
Allyl 6.1 UN1545 II 6.1, 3.... A3, A7, IB2, T7, None.......... 202........ 243........ Forbidden 60 L D 40
isothiocyanate, TP2
stabilized.
Allylamine.......... 6.1 UN2334 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, T20, TP2,
TP13, TP38, TP45
Allyltrichlorosilane 8 UN1724 II 8, 3...... A7, B2, B6, IB2, None.......... 202........ 243........ Forbidden 30 L C 40
, stabilized. N34, T7, TP2,
TP13
Aluminum alkyl 4.2 UN3052 I 4.2, 4.3.. B9, B11, T21, None.......... 181........ 244........ Forbidden Forbidden D .......
halides. TP2, TP7
Aluminum alkyl 4.2 UN3076 I 4.2, 4.3.. B9, B11, T21, None.......... 181........ 244........ Forbidden Forbidden D .......
hydrides. TP2, TP7
Aluminum alkyls..... 4.2 UN3051 I 4.2, 4.3.. B9, B11, T21, None.......... 181........ 244........ Forbidden Forbidden D .......
TP2, TP7
[[Page 113]]
Aluminum borohydride 4.2 UN2870 I 4.2, 4.3.. B11 None.......... 181........ 244........ Forbidden Forbidden D .......
or Aluminum
borohydride in
devices.
Aluminum bromide, 8 UN1725 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A 40
anhydrous.
Aluminum bromide, 8 UN2580 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
solution.
Aluminum carbide.... 4.3 UN1394 II 4.3....... A20, IB7, IP2, 151........... 212........ 242........ 15 kg 50 kg A .......
N41
Aluminum chloride, 8 UN1726 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A 40
anhydrous.
Aluminum chloride, 8 UN2581 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
solution.
Aluminum dross, wet Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
or hot.
Aluminum 4.3 UN1395 II 4.3, 6.1.. A19, IB5, IP2 151........... 212........ 242........ 15 kg 50 kg A 40, 85,
ferrosilicon powder. 103
.................... ........... .................. III 4.3, 6.1.. A19, A20, IB4 151........... 213........ 241........ 25 kg 100 kg A 40, 85,
103
Aluminum hydride.... 4.3 UN2463 I 4.3....... A19, N40 None.......... 211........ 242........ Forbidden 15 kg E .......
D Aluminum, molten.... 9 NA9260 III 9......... IB3, T1, TP3 None.......... None....... 247........ Forbidden Forbidden D .......
Aluminum nitrate.... 5.1 UN1438 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A .......
IP3
Aluminum phosphate ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solution, see
Corrosive liquids,
etc.
Aluminum phosphide.. 4.3 UN1397 I 4.3, 6.1.. A8, A19, N40 None.......... 211........ 242........ Forbidden 15 kg E 40, 85
Aluminum phosphide 6.1 UN3048 I 6.1....... A8, IB7, IP1 None.......... 211........ 242........ Forbidden 15 kg E 40, 85
pesticides.
Aluminum powder, 4.1 UN1309 II 4.1....... IB8, IP2, IP4 151........... 212........ 240........ 15 kg 50 kg A 13, 39,
coated. 101
.................... ........... .................. III 4.1....... IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A 13, 39,
101
Aluminum powder, 4.3 UN1396 II 4.3....... A19, A20, IB7, 151........... 212........ 242........ 15 kg 50 kg A 39
uncoated. IP2
.................... ........... .................. III 4.3....... A19, A20, IB8, 151........... 213........ 241........ 25 kg 100 kg A 39
IP4
Aluminum resinate... 4.1 UN2715 III 4.1....... IB6 151........... 213........ 240........ 25 kg 100 kg A .......
Aluminum silicon 4.3 UN1398 III 4.3....... A1, A19, IB8, 151........... 213........ 241........ 25 kg 100 kg A 40, 85,
powder, uncoated. IP4 103
Aluminum smelting by- 4.3 UN3170 II 4.3....... 128, B115, IB7, None.......... 212........ 242........ 15 kg 50 kg B 85, 103
products or IP2
Aluminum remelting
by-products.
.................... ........... .................. III 4.3....... 128, B115, IB8, None.......... 213........ 241........ 25 kg 100 kg B 85, 103
IP4
Amatols, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Explosives,
blasting, type B.
G Amines, flammable, 3 UN2733 I 3, 8...... T14, TP1, TP27 None.......... 201........ 243........ 0.5 L 2.5 L D 40
corrosive, n.o.s.
or Polyamines,
flammable,
corrosive, n.o.s..
.................... ........... .................. II 3, 8...... IB2, T11, TP1, None.......... 202........ 243........ 1 L 5 L B 40
TP27
.................... ........... .................. III 3, 8...... B1, IB3, T7, 150........... 203........ 242........ 5 L 60 L A 40
TP1, TP28
G Amines, liquid, 8 UN2734 I 8, 3...... A3, A6, N34, None.......... 201........ 243........ 0.5 L 2.5 L A .......
corrosive, T14, TP2, TP27
flammable, n.o.s.
or Polyamines,
liquid, corrosive,
flammable, n.o.s..
[[Page 114]]
.................... ........... .................. II 8, 3...... IB2, T11, TP2, None.......... 202........ 243........ 1 L 30 L A .......
TP27
G Amines, liquid, 8 UN2735 I 8......... A3, A6, B10, None.......... 201........ 243........ 0.5 L 2.5 L A .......
corrosive, n.o.s, N34, T14, TP2,
or Polyamines, TP27
liquid, corrosive,
n.o.s..
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L A .......
TP1, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A .......
TP28
G Amines, solid, 8 UN3259 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg A .......
corrosive, n.o.s.,
or Polyamines,
solid, corrosive
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
2-Amino-4- 6.1 UN2673 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
chlorophenol.
2-Amino-5- 6.1 UN2946 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
diethylaminopentane.
2-Amino-4,6- 4.1 UN3317 I 4.1....... 23, A8, A19, None.......... 211........ None....... 1 kg 15 kg E 28, 36
Dinitrophenol, A20, N41
wetted with not
less than 20
percent water by
mass.
2-(2-Aminoethoxy) 8 UN3055 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
ethanol.
N- 8 UN2815 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A 12
Aminoethylpiperazin
e.
+ Aminophenols (o-; m- 6.1 UN2512 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A .......
; p-). TP1
Aminopropyldiethanol ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
amine, see Amines,
etc.
n- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Aminopropylmorpholi
ne, see Amines, etc.
Aminopyridines (o-; 6.1 UN2671 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg B 12, 40
m-; p-). T7, TP2
I Ammonia, anhydrous.. 2.3 UN1005 ....... 2.3, 8.... 4, T50 None.......... 304........ 314, 315... Forbidden 25 kg D 40, 57
D Ammonia, anhydrous.. 2.2 UN1005 ....... 2.2....... 13, T50 None.......... 304........ 314, 315... Forbidden 25 kg D 40, 57
D Ammonia solution, 2.2 UN3318 ....... 2.2....... 13, T50 None.......... 304........ 314, 315... Forbidden 25 kg D 40, 57
relative density
less than 0.880 at
15 degrees C in
water, with more
than 50 percent
ammonia.
[[Page 115]]
I Ammonia solution, 2.3 UN3318 ....... 2.3, 8.... 4, T50 None.......... 304........ 314, 315... Forbidden 25 kg D 40, 57
relative density
less than 0.880 at
15 degrees C in
water, with more
than 50 percent
ammonia.
Ammonia solutions, 8 UN2672 III 8......... IB3, T7, TP1 154........... 203........ 241........ 5 L 60 L A 40, 85
relative density
between 0.880 and
0.957 at 15 degrees
C in water, with
more than 10
percent but not
more than 35
percent ammonia.
Ammonia solutions, 2.2 UN2073 ....... 2.2....... 306........... 304........ 314, 315... Forbidden 150 kg E 40, 57
relative density
less than 0.880 at
15 degrees C in
water, with more
than 35 percent but
not more than 50
percent ammonia.
Ammonium arsenate... 6.1 UN1546 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Ammonium azide...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonium bifluoride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, see Ammonium
hydrogen
difluoride, solid.
Ammonium bifluoride ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solution, see
Ammonium hydrogen
difluoride,
solution.
Ammonium bromate.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonium chlorate... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonium dichromate. 5.1 UN1439 II 5.1....... IB8, IP2, IP4 152........... 212........ 242........ 5 kg 25 kg A .......
Ammonium dinitro-o- 6.1 UN1843 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg B 36, 65,
cresolate. T7, TP2 66, 77
Ammonium fluoride... 6.1 UN2505 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 26
Ammonium 6.1 UN2854 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 26
fluorosilicate.
Ammonium fulminate.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonium hydrogen 8 UN2506 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A 40
sulfate.
Ammonium 8 UN1727 II 8......... IB8, IP2, IP4, 154........... 212........ 240........ 15 kg 50 kg A 25, 26,
hydrogendifluoride, N34 40
solid.
Ammonium 8 UN2817 II 8, 6.1.... IB2, N34, T8, None.......... 202........ 243........ 1 L 30 L B 40
hydrogendifluoride, TP2, TP12, TP13
solution.
.................... ........... .................. III 8, 6.1.... IB3, T4, TP1, 154........... 203........ 241........ 5 L 60 L B 40, 95
TP12, TP13
Ammonium ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydrosulfide,
solution, see
Ammonium sulfide
solution.
D Ammonium hydroxide, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ammonia
solutions, etc.
Ammonium 6.1 UN2859 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
metavanadate.
D Ammonium nitrate 5.1 NA2072 III 5.1....... 7, IB8 152........... 213........ 240........ 25 kg 100 kg B 48, 59,
fertilizers. 60, 117
[[Page 116]]
Ammonium nitrate 5.1 UN2067 III 5.1....... 52, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg B 48, 59,
fertilizers; 60, 117
uniform non-
segregating
mixtures of
ammonium nitrate
with added matter
which is inorganic
and chemically
inert towards
ammonium nitrate,
with not less than
90 percent ammonium
nitrate and not
more than 0.2
percent combustible
material (including
organic material
calculated as
carbon), or with
more than 70
percent but less
than 90 percent
ammonium nitrate
and not more than
0.4 percent total
combustible
material.
A W Ammonium nitrate 9 UN2071 III 9......... 132, IB8 155........... 213........ 240........ 200 kg 200 kg A .......
fertilizers:
uniform non-
segregating
mixtures of
nitrogen/phosphate
or nitrogen/postash
types or complete
fertilizers of
nitrogen/phosphate/
postash type, with
not more than 70
percent ammonium
nitrate and not
more than 0.4
percent total added
combustible
material or with
not more than 45
percent ammonium
nitrate with
unrestricted
combustible
material.
D Ammonium nitrate- 1.5D NA0331 II 1.5D...... None.......... 62......... None....... Forbidden Forbidden 10 19E
fuel oil mixture
containing only
prilled ammonium
nitrate and fuel
oil.
Ammonium nitrate, 5.1 UN2426 ....... 5.1....... B5, T7 None.......... None....... 243........ Forbidden Forbidden D 59, 60
liquid (hot
concentrated
solution).
D Ammonium nitrate 5.1 NA2069 III 5.1....... 10, IB8 152........... 213........ 240........ 25 kg 100 kg B 48, 59,
mixed fertlizers. 60, 117
[[Page 117]]
Ammonium nitrate, 1.1D UN0222 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 19E
with more than 0.2
percent combustible
substances,
including any
organic substance
calculated as
carbon, to the
exclusion of any
other added
substance.
Ammonium nitrate, 5.1 UN1942 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A 48, 59,
with not more than IP3 60, 116
0.2 percent of
combustible
substances,
including any
organic substance
calculated as
carbon, to the
exclusion of any
other added
substance.
Ammonium nitrite.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonium perchlorate 1.1D UN0402 II 1.1D...... 107 None.......... 62......... None....... Forbidden Forbidden 10 19E
Ammonium perchlorate 5.1 UN1442 II 5.1....... 107, A9, IB6, 152........... 212........ 242........ 5 kg 25 kg E 58, 69,
IP2 106
Ammonium Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
permanganate.
Ammonium persulfate. 5.1 UN1444 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A .......
IP3
Ammonium picrate, 1.1D UN0004 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 5E, 19E
dry or wetted with
less than 10
percent water, by
mass.
Ammonium picrate, 4.1 UN1310 I 4.1....... 23, A2, N41 None.......... 211........ None....... 0.5 kg 0.5 kg D 28, 36
wetted with not
less than 10
percent water, by
mass.
Ammonium 8 UN2818 II 8, 6.1.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 30 L B 12, 26,
polysulfide, TP13 40
solution.
.................... ........... .................. III 8, 6.1.... IB3, T4, TP1, 154........... 203........ 241........ 5 L 60 L B 12, 26,
TP13 40
Ammonium 6.1 UN2861 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
polyvanadate.
Ammonium ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
silicofluoride, see
Ammonium
fluorosilicate.
Ammonium sulfide 8 UN2683 II 8, 6.1, 3. IB1, T7, TP2, None.......... 202........ 243........ 1 L 30 L B 12, 22,
solution. TP13 26, 100
Ammunition, blank, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Cartridges for
weapons, blank.
Ammunition, 1.2G UN0171 II 1.2G...... ............. 62......... None....... Forbidden Forbidden 03 .......
illuminating with
or without burster,
expelling charge or
propelling charge.
Ammunition, 1.3G UN0254 II 1.3G...... ............. 62......... None....... Forbidden Forbidden 03 .......
illuminating with
or without burster,
expelling charge or
propelling charge.
Ammunition, 1.4G UN0297 II 1.4G...... ............. 62......... None....... Forbidden 75 kg 02 .......
illuminating with
or without burster,
expelling charge or
propelling charge.
Ammunition, 1.3J UN0247 II 1.3J...... ............. 62......... None....... Forbidden Forbidden 04 23E
incendiary liquid
or gel, with
burster, expelling
charge or
propelling charge.
[[Page 118]]
Ammunition, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
incendiary (water-
activated
contrivances) with
burster, expelling
charge or
propelling charge,
see Contrivances,
water-activated,
etc..
Ammunition, 1.2H UN0243 II 1.2H...... ............. 62......... None....... Forbidden Forbidden 08 8E,
incendiary, white 14E,
phosphorus, with 15E,
burster, expelling 17E
charge or
propelling charge.
Ammunition, 1.3H UN0244 II 1.3H...... ............. 62......... None....... Forbidden Forbidden 08 8E,
incendiary, white 14E,
phosphorus, with 15E,
burster, expelling 17E
charge or
propelling charge.
Ammunition, 1.2G UN0009 II 1.2G...... ............. 62......... None....... Forbidden Forbidden 03 .......
incendiary with or
without burster,
expelling charge,
or propelling
charge.
Ammunition, 1.3G UN0010 II 1.3G...... ............. 62......... None....... Forbidden Forbidden 03 .......
incendiary with or
without burster,
expelling charge,
or propelling
charge.
Ammunition, 1.4G UN0300 II 1.4G...... ............. 62......... None....... Forbidden 75 kg 02 .......
incendiary with or
without burster,
expelling charge or
propelling charge.
Ammunition, practice 1.4G UN0362 II 1.4G...... ............. 62......... None....... Forbidden 75 kg 02 .......
Ammunition, practice 1.3G UN0488 II 1.3G...... ............. 62......... None....... Forbidden Forbidden 03 .......
Ammunition, proof... 1.4G UN0363 II 1.4G...... ............. 62......... None....... Forbidden 75 kg 02 .......
Ammunition, rocket, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Warheads,
rocket etc.
Ammunition, SA ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(small arms), see
Cartridges for
weapons, etc.
Ammunition, smoke ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(water-activated
contrivances),
white phosphorus,
with burster,
expelling charge or
propelling charge,
see Contrivances,
water-activated,
etc. (UN 0248).
[[Page 119]]
Ammunition, smoke ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(water-activated
contrivances),
without white
phosphorus or
phosphides, with
burster, expelling
charge or
propelling charge,
see Contrivances,
water-activated,
etc. (UN 0249).
Ammunition smoke, 1.2H UN0245 II 1.2H...... ............. 62......... None....... Forbidden Forbidden 08 8E,
white phosphorus 14E,
with 15E,
burster,expelling 17E
charge, or
propelling charge.
Ammunition, smoke, 1.3H UN0246 II 1.3H...... ............. 62......... None....... Forbidden Forbidden 08 8E,
white phosphorus 14E,
with burster, 15E,
expelling charge, 17E
or propelling
charge.
Ammunition, smoke 1.2G UN0015 II 1.2G, 8... ............. 62......... None....... Forbidden Forbidden ............ 8E,
with or without 17E,
burster, expelling 20E
charge or
propelling charge.
Ammunition, smoke 1.3G UN0016 II 1.3G, 8... ............. 62......... None....... Forbidden Forbidden ............ 8E,
with or without 17E,
burster, expelling 20E
charge or
propelling charge.
Ammunition, smoke 1.4G UN0303 II 1.4G, 8... ............. 62......... None....... Forbidden 75 kg ............ 7E, 8E,
with or without 14E,
burster, expelling 15E,
charge or 17E
propelling charge.
Ammunition, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
sporting, see
Cartridges for
weapons, etc. (UN
0012; UN 0328; UN
0339).
Ammunition, tear- 6.1 UN2017 II 6.1, 8.... None.......... 212........ None....... Forbidden 50 kg E 13, 40
producing, non-
explosive, without
burster or
expelling charge,
non-fuzed.
Ammunition, tear- 1.2G UN0018 II 1.2G, 8, ............. 62......... None....... Forbidden Forbidden ............ 8E,
producing with 6.1. 17E,
burster, expelling 20E
charge or
propelling charge.
Ammunition, tear- 1.3G UN0019 II 1.3G, 8, ............. 62......... None....... Forbidden Forbidden ............ 8E,
producing with 6.1. 17E,
burster, expelling 20E
charge or
propelling charge.
Ammunition, tear- 1.4G UN0301 II 1.4G, 8, ............. 62......... None....... Forbidden 75 kg ............ 7E, 8E,
producing with 6.1. 14E,
burster, expelling 15E,
charge or 17E
propelling charge.
Ammunition, toxic, 6.1 UN2016 II 6.1....... None.......... 212........ None....... Forbidden 100 kg E 13, 40
non-explosive,
without burster or
expelling charge,
non-fuzed.
Ammunition, toxic ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(water-activated
contrivances), with
burster, expelling
charge or
propelling charge,
see Contrivances,
water-activated,
etc.
[[Page 120]]
G Ammunition, toxic 1.2K UN0020 II 1.2K, 6.1. ............. 62......... None....... Forbidden Forbidden 08 8E,
with burster, 14E,
expelling charge, 15E,
or propelling 17E
charge.
G Ammunition, toxic 1.3K UN0021 II 1.3K, 6.1. ............. 62......... None....... Forbidden Forbidden 08 8E,
with burster, 14E,
expelling charge, 15E,
or propelling 17E
charge.
Amyl acetates....... 3 UN1104 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Amyl acid phosphate. 8 UN2819 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Amyl butyrates...... 3 UN2620 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Amyl chlorides...... 3 UN1107 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Amyl formates....... 3 UN1109 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Amyl mercaptans..... 3 UN1111 II 3......... A3, IB2, T4, TP1 None.......... 202........ 242........ 5 L 60 L B 95, 102
n-Amyl methyl ketone 3 UN1110 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Amyl nitrate........ 3 UN1112 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A 40
Amyl nitrites....... 3 UN1113 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E 40
Amylamines.......... 3 UN1106 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
.................... ........... .................. III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A .......
Amyltrichlorosilane. 8 UN1728 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
N34, T7, TP2,
TP13
Anhydrous ammonia, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ammonia,
anhydrous.
Anhydrous ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydrofluoric acid,
see Hydrogen
fluoride, anhydrous.
+ Aniline............. 6.1 UN1547 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 40
Aniline 6.1 UN1548 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
hydrochloride.
Aniline oil, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Aniline.
Anisidines.......... 6.1 UN2431 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Anisole............. 3 UN2222 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Anisoyl chloride.... 8 UN1729 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L C 40
Anti-freeze, liquid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Flammable
liquids, n.o.s..
Antimonous chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Antimony
trichloride.
Antimony compounds, 6.1 UN3141 III 6.1....... 35, IB3, T7, 153........... 203........ 241........ 60 L 220 L A .......
inorganic, liquid, TP1, TP28
n.o.s..
[[Page 121]]
Antimony compounds, 6.1 UN1549 III 6.1....... 35, IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
inorganic, solid,
n.o.s..
Antimony lactate.... 6.1 UN1550 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Antimony 8 UN1730 II 8......... B2, IB2, T7, TP2 None.......... 202........ 242........ 1 L 30 L C 40
pentachloride,
liquid.
Antimony 8 UN1731 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L C 40
pentachloride,
solutions.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L C 40
Antimony 8 UN1732 II 8, 6.1.... A3, A6, A7, A10, None.......... 202........ 243........ Forbidden 30 L D 40
pentafluoride. IB2, N3, T7, TP2
Antimony potassium 6.1 UN1551 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
tartrate.
Antimony powder..... 6.1 UN2871 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Antimony sulfide and Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
a chlorate,
mixtures of.
Antimony sulfide, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, see Antimony
compounds,
inorganic, n.o.s..
Antimony 8 UN1733 II 8......... B2, IB2 154........... 202........ 242........ 1 L 30 L C 40
trichloride, liquid.
Antimony 8 UN1733 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A 40
trichloride, solid.
Aqua ammonia, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammonia solution,
etc.
Argon, compressed... 2.2 UN1006 ....... 2.2....... 306........... 302........ 314, 315... 75 kg 150 kg A .......
Argon, refrigerated 2.2 UN1951 ....... 2.2....... T75, TP5 320........... 316........ 318........ 50 kg 500 kg B .......
liquid (cryogenic
liquid).
Arsenic............. 6.1 UN1558 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Arsenic acid, liquid 6.1 UN1553 I 6.1....... T20, TP2, TP7, None.......... 201........ 243........ 1 L 30 L B 46
TP13
Arsenic acid, solid. 6.1 UN1554 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Arsenic bromide..... 6.1 UN1555 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 12, 40
Arsenic chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Arsenic
trichloride.
Arsenic compounds, 6.1 UN1556 I 6.1....... None.......... 201........ 243........ 1 L 30 L B 40
liquid, n.o.s.
inorganic,
including
arsenates, n.o.s.;
arsenites, n.o.s.;
arsenic sulfides,
n.o.s.; and organic
compounds of
arsenic, n.o.s..
.................... ........... .................. II 6.1....... IB2 None.......... 202........ 243........ 5 L 60 L B 40
.................... ........... .................. III 6.1....... IB3 153........... 203........ 241........ 60 L 220 L B 40
Arsenic compounds, 6.1 UN1557 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A .......
solid, n.o.s.
inorganic,
including
arsenates, n.o.s.;
arsenites, n.o.s.;
arsenic sulfides,
n.o.s.; and organic
compounds of
arsenic, n.o.s..
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Arsenic pentoxide... 6.1 UN1559 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Arsenic sulfide and Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
a chlorate,
mixtures of.
[[Page 122]]
Arsenic trichloride. 6.1 UN1560 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden B 40
B74, T20, TP2,
TP13, TP38, TP45
Arsenic trioxide.... 6.1 UN1561 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Arsenic, white, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, see Arsenic
trioxide.
Arsenical dust...... 6.1 UN1562 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Arsenical 3 UN2760 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L B 40
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Arsenical 6.1 UN2994 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Arsenical 6.1 UN2993 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic, flammable
flash point not
less than 23
degrees C.
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1, 3.... B1, IB3, T7, 153........... 203........ 242........ 60 L 220 L A 40
TP2, TP28
Arsenical 6.1 UN2759 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid,
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Arsenious acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, see Arsenic
trioxide.
Arsenious and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mercuric iodide
solution, see
Arsenic compounds,
liquid, n.o.s..
Arsine.............. 2.3 UN2188 ....... 2.3, 2.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
Articles, explosive, 1.6N UN0486 II 1.6N...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
extremely
insensitive or
Articles, EEI.
G Articles, explosive, 1.4S UN0349 II 1.4S...... 101 None.......... 62......... None....... 25 kg 100 kg 05 .......
n.o.s..
[[Page 123]]
G Articles, explosive, 1.4B UN0350 II 1.4B...... 101 None.......... 62......... None....... Forbidden Forbidden 06 .......
n.o.s..
G Articles, explosive, 1.4C UN0351 II 1.4C...... 101 None.......... 62......... None....... Forbidden 75 kg 06 .......
n.o.s..
G Articles, explosive, 1.4D UN0352 II 1.4D...... 101 None.......... 62......... None....... Forbidden 75 kg 06 .......
n.o.s..
G Articles, explosive, 1.4G UN0353 II 1.4G...... 101 None.......... 62......... None....... Forbidden 75 kg 06 .......
n.o.s..
G Articles, explosive, 1.1L UN0354 II 1.1L...... 101 None.......... 62......... None....... Forbidden Forbidden 08 8E,
n.o.s.. 14E,
15E,
17E
G Articles, explosive, 1.2L UN0355 II 1.2L...... 101 None.......... 62......... None....... Forbidden Forbidden 08 8E,
n.o.s.. 14E,
15E,
17E
G Articles, explosive, 1.3L UN0356 II 1.3L...... 101 None.......... 62......... None....... Forbidden Forbidden 08 8E,
n.o.s.. 14E,
15E,
17E
G Articles, explosive, 1.1C UN0462 II 1.1C...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.1D UN0463 II 1.1D...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.1E UN0464 II 1.1E...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.1F UN0465 II 1.1F...... 101 None.......... 62......... None....... Forbidden Forbidden 08 .......
n.o.s..
G Articles, explosive, 1.2C UN0466 II 1.2C...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.2D UN0467 II 1.2D...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.2E UN0468 II 1.2E...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.2F UN0469 II 1.2F...... 101 None.......... 62......... None....... Forbidden Forbidden 08 .......
n.o.s..
G Articles, explosive, 1.3C UN0470 II 1.3C...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
n.o.s..
G Articles, explosive, 1.4E UN0471 II 1.4E...... 101 None.......... 62......... None....... Forbidden 75 kg 06 .......
n.o.s..
G Articles, explosive, 1.4F UN0472 II 1.4F...... 101 None.......... 62......... None....... Forbidden Forbidden 08 .......
n.o.s..
Articles, 2.2 UN3164 ....... 2.2....... 306........... 302, 304... None....... No limit No limit A .......
pressurized
pneumatic or
hydraulic
containing non-
flammable gas.
Articles, pyrophoric 1.2L UN0380 II 1.2L...... None.......... 62......... None....... Forbidden Forbidden 08 8E,
14E,
15E,
17E
Articles, 1.1G UN0428 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
pyrotechnic for
technical purposes.
Articles, 1.2G UN0429 II 1.2G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
pyrotechnic for
technical purposes.
Articles, 1.3G UN0430 II 1.3G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
pyrotechnic for
technical purposes.
Articles, 1.4G UN0431 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
pyrotechnic for
technical purposes.
Articles, 1.4S UN0432 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
pyrotechnic for
technical purposes.
D Asbestos............ 9 NA2212 III 9......... IB8, IP2, IP4 155........... 216........ 240........ 200 kg 200 kg A 34, 40
Ascaridole (organic Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide).
D Asphalt, at or above 3 NA1999 III 3......... IB3, T1, TP3 150........... 203........ 247........ Forbidden Forbidden D .......
its flash point.
D Asphalt, cut back, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Tars, liquid,
etc.
[[Page 124]]
Automobile, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
motorcycle,
tractor, other self-
propelled vehicle,
engine, or other
mechanical
apparatus, see
Vehicles or Battery
etc.
A G Aviation regulated 9 UN3334 ....... 9......... A35 155........... 204........ .......... No limit No limit A .......
liquid, n.o.s..
A G Aviation regulated 9 UN3335 ....... 9......... A35 155........... 204........ .......... No limit No limit A .......
solid, n.o.s..
Azaurolic acid (salt Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
of) (dry).
Azido guanidine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
picrate (dry).
5-Azido-1-hydroxy Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetrazole.
Azido hydroxy Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetrazole (mercury
and silver salts).
3-Azido-1,2- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Propylene glycol
dinitrate.
Azidodithiocarbonic Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
acid.
Azidoethyl nitrate.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
1- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Aziridinylphosphine
oxide-(tris), see
Tris-(1-aziridinyl)
phosphine oxide,
solution.
Azodicarbonamide.... 4.1 UN3242 II 4.1....... 38, IB8 151........... 212........ 240........ Forbidden Forbidden D 12, 61,
74
Azotetrazole (dry).. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Barium.............. 4.3 UN1400 II 4.3....... A19, IB7, IP2 151........... 212........ 241........ 15 kg 50 kg E .......
Barium alloys, 4.2 UN1854 I 4.2....... None.......... 181........ None....... Forbidden Forbidden D .......
pyrophoric.
Barium azide, dry or 1.1A UN0224 II 1.1A, 6.1. 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
wetted with less
than 50 percent
water, by mass.
Barium azide, wetted 4.1 UN1571 I 4.1, 6.1.. A2 None.......... 182........ None....... Forbidden 0.5 kg D 28
with not less than
50 percent water,
by mass.
Barium bromate...... 5.1 UN2719 II 5.1, 6.1.. IB8, IP2, IP4 None.......... 212........ 242........ 5 kg 25 kg A 56, 58,
106
Barium chlorate..... 5.1 UN1445 II 5.1, 6.1.. A9, IB6, IP2, None.......... 212........ 242........ 5 kg 25 kg A 56, 58,
N34, T4, TP1 106
Barium compounds, 6.1 UN1564 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
n.o.s..
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Barium cyanide...... 6.1 UN1565 I 6.1....... IB7, IP1, N74, None.......... 211........ 242........ 5 kg 50 kg A 26, 40
N75
[[Page 125]]
Barium hypochlorite 5.1 UN2741 II 5.1, 6.1.. A7, A9, IB8, 152........... 212........ None....... 5 kg 25 kg B 56, 58,
with more than 22 IP2, IP4, N34 106
percent available
chlorine.
Barium nitrate...... 5.1 UN1446 II 5.1, 6.1.. IB8, IP2, IP4 None.......... 212........ 242........ 5 kg 25 kg A .......
Barium oxide........ 6.1 UN1884 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Barium perchlorate.. 5.1 UN1447 II 5.1, 6.1.. IB6, IP2, T4, None.......... 212........ 242........ 5 kg 25 kg A 56, 58,
TP1 106
Barium permanganate. 5.1 UN1448 II 5.1, 6.1.. IB6, IP2 None.......... 212........ 242........ 5 kg 25 kg D 56, 58,
69,
106,
107
Barium peroxide..... 5.1 UN1449 II 5.1, 6.1.. IB6, IP2 None.......... 212........ 242........ 5 kg 25 kg A 13, 75,
106
Barium selenate, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Selenates or
Selenites.
Barium selenite, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Selenates or
Selenites.
Batteries, 4.3 UN3292 II 4.3....... 189........... 189........ 189........ Forbidden No limit A .......
containing sodium.
Batteries, dry, 8 UN3028 III 8......... None.......... 213........ None....... 25 kg gross 230 kg A .......
containing gross
potassium hydroxide
solid, electric,
storage.
Batteries, wet, 8 UN2794 III 8......... 159........... 159........ 159........ 30 kg gross No limit A .......
filled with acid,
electric storage.
Batteries, wet, non- 8 UN2800 III 8......... 159........... 159........ 159........ No Limit No Limit A .......
spillable, electric
storage.
Batteries, dry, not ........... .................. .......... 130 ............. .......... .......... ........... ........... ............ .......
subject to the
requirements of
this subchapter.
Battery fluid, acid. 8 UN2796 II 8......... A3, A7, B2, B15, 154........... 202........ 242........ 1 L 30 L B .......
IB2, N6, N34,
T8, TP2, TP12
Battery fluid, 8 UN2797 II 8......... B2, IB2, N6, T7, 154........... 202........ 242........ 1 L 30 L A .......
alkali. TP2
Battery lithium ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
type, see Lithium
batteries etc.
Battery-powered 9 UN3171 ....... 9......... 134 220........... 220........ None....... No limit No limit ............ .......
vehicle or Battery-
powered equipment.
Battery, wet, filled ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
with acid or alkali
with vehicle or
mechanical
equipment
containing an
internal combustion
engine, see
Vehicle, etc. or
Engines, internal
combustion, etc.
+ Benzaldehyde........ 9 UN1990 III 9......... IB3, T2, TP1 155........... 203........ 241........ 100 L 220 L A .......
Benzene............. 3 UN1114 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Benzene diazonium Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
chloride (dry).
Benzene diazonium Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrate (dry).
[[Page 126]]
Benzene phosphorus ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
dichloride, see
Phenyl phosphorus
dichloride.
Benzene phosphorus ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
thiodichloride, see
Phenyl phosphorus
thiodichloride.
Benzene sulfonyl 8 UN2225 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A 40
chloride.
Benzene triozonide.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Benzenethiol, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Phenyl mercaptan.
Benzidine........... 6.1 UN1885 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Benzol, see Benzene. ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Benzonitrile........ 6.1 UN2224 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 26, 40
Benzoquinone........ 6.1 UN2587 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Benzotrichloride.... 8 UN2226 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A 40
Benzotrifluoride.... 3 UN2338 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Benzoxidiazoles Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Benzoyl azide....... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Benzoyl chloride.... 8 UN1736 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L C 40
TP2, TP12, TP13
Benzyl bromide...... 6.1 UN1737 II 6.1, 8.... A3, A7, IB2, None.......... 202........ 243........ 1 L 30 L D 13, 40
N33, N34, T8,
TP2, TP12, TP13
Benzyl chloride..... 6.1 UN1738 II 6.1, 8.... A3, A7, B70, None.......... 202........ 243........ 1 L 30 L D 13, 40
IB2, N33, N42,
T8, TP2, TP12,
TP13
Benzyl chloride 6.1 UN1738 II 6.1, 8.... A3, A7, B8, B11, None.......... 202........ 243........ 1 L 30 L D 13, 40
unstabilized. IB2, N33, N34,
N43, T8, TP2,
TP12, TP13
Benzyl chloroformate 8 UN1739 I 8......... A3, A6, B4, N41, None.......... 201........ 243........ Forbidden 2.5 L D 40
T10, TP2, TP12,
TP13
Benzyl iodide....... 6.1 UN2653 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L B 12, 40
Benzyldimethylamine. 8 UN2619 II 8, 3...... B2, IB2, T7, TP2 154........... 202........ 243........ 1 L 30 L A 40, 48
Benzylidene chloride 6.1 UN1886 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L D 40
Beryllium compounds, 6.1 UN1566 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
n.o.s..
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
[[Page 127]]
Beryllium nitrate... 5.1 UN2464 II 5.1, 6.1.. IB8, IP2, IP4 None.......... 212........ 242........ 5 kg 25 kg A .......
Beryllium, powder... 6.1 UN1567 II 6.1, 4.1.. IB8, IP2, IP4 None.......... 212........ 242........ 15 kg 50 kg A .......
Bicyclo [2,2,1] 3 UN2251 II 3......... IB2, T7, TP2 150........... 202........ 242........ 5 L 60 L D .......
hepta-2,5-diene,
stabilized or 2,5-
Norbornadiene,
stabilized.
Biphenyl triozonide. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Bipyridilium 3 UN2782 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L E .......
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Bipyridilium 6.1 UN3016 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Bipyridilium 6.1 UN3015 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 21, 40
pesticides, liquid, TP27
toxic, flammable,
flash point not
less than 23
degrees C.
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 21, 40
TP13, TP27
.................... ........... .................. III 6.1, 3.... B1, IB3, T7, 153........... 203........ 242........ 60 L 220 L A 21, 40
TP2, TP28
Bipyridilium 6.1 UN2781 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid,
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Bis (Aminopropyl) ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
piperazine, see
Corrosive liquid,
n.o.s..
Bisulfate, aqueous 8 UN2837 II 8......... A7, B2, IB2, 154........... 202........ 242........ 1 L 30 L A .......
solution. N34, T7, TP2
.................... ........... .................. III 8......... A7, IB3, N34, 154........... 203........ 241........ 5 L 60 L A .......
T4, TP1
Bisulfites, aqueous 8 UN2693 III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 26, 40
solutions, n.o.s.. TP28
Black powder, 1.1D UN0028 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
compressed or
Gunpowder,
compressed or Black
powder, in pellets
or Gunpowder, in
pellets.
Black powder or 1.1D UN0027 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
Gunpowder, granular
or as a meal.
D Black powder for 4.1 NA0027 I 4.1....... 70 None.......... 170........ None....... Forbidden Forbidden E .......
small arms.
Blasting agent, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
n.o.s., see
Explosives,
blasting etc.
Blasting cap ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
assemblies, see
Detonator
assemblies, non-
electric, for
blasting.
[[Page 128]]
Blasting caps, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
electric, see
Detonators,
electric for
blasting.
Blasting caps, non- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
electric, see
Detonators, non-
electric, for
blasting.
Bleaching powder, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Calcium
hypochlorite
mixtures, etc.
I Blue asbestos 9 UN2212 II 9......... IB8, IP2, IP4 155........... 216........ 240........ Forbidden Forbidden A 34, 40
(Crocidolite) or
Brown asbestos
(amosite, mysorite).
Bombs, photo-flash.. 1.1F UN0037 II 1.1F...... ............. 62......... None....... Forbidden Forbidden 08 .......
Bombs, photo-flash.. 1.1D UN0038 II 1.1D...... ............. 62......... None....... Forbidden Forbidden 03 .......
Bombs, photo-flash.. 1.2G UN0039 II 1.2G...... ............. 62......... None....... Forbidden Forbidden 03 .......
Bombs, photo-flash.. 1.3G UN0299 II 1.3G...... ............. 62......... None....... Forbidden Forbidden 03 .......
Bombs, smoke, non- 8 UN2028 II 8......... None.......... 160........ None....... Forbidden 50 kg E 40
explosive, with
corrosive liquid,
without initiating
device.
Bombs, with bursting 1.1F UN0033 II 1.1F...... ............. 62......... None....... Forbidden Forbidden 08 .......
charge.
Bombs, with bursting 1.1D UN0034 II 1.1D...... ............. 62......... None....... Forbidden Forbidden 03 .......
charge.
Bombs, with bursting 1.2D UN0035 II 1.2D...... ............. 62......... None....... Forbidden Forbidden 03 .......
charge.
Bombs, with bursting 1.2F UN0291 II 1.2F...... ............. 62......... None....... Forbidden Forbidden 08 .......
charge.
Bombs with flammable 1.1J UN0399 II 1.1J...... ............. 62......... None....... Forbidden Forbidden 04 23E
liquid, with
bursting charge.
Bombs with flammable 1.2J UN0400 II 1.2J...... ............. 62......... None....... Forbidden Forbidden 04 23E
liquid, with
bursting charge.
Boosters with 1.1B UN0225 II 1.1B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
detonator.
Boosters with 1.2B UN0268 II 1.2B...... None.......... 62......... None....... Forbidden Forbidden 07 .......
detonator.
Boosters, without 1.1D UN0042 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
detonator.
Boosters, without 1.2D UN0283 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
detonator.
Borate and chlorate ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures, see
Chlorate and borate
mixtures.
Borneol............. 4.1 UN1312 III 4.1....... A1, IB8, IP3 None.......... 213........ 240........ 25 kg 100 kg A .......
+ Boron tribromide.... 8 UN2692 I 8, 6.1.... 2, A3, A7, B9, None.......... 227........ 244........ Forbidden Forbidden C 12
B14, B32, B74,
N34, T20, TP2,
TP12, TP13,
TP38, TP45
Boron trichloride... 2.3 UN1741 ....... 2.3, 8.... 3, B9, B14 None.......... 304........ 314........ Forbidden Forbidden D 25, 40
[[Page 129]]
Boron trifluoride, 2.3 UN1008 ....... 2.3....... 2, B9, B14 None.......... 302........ 314, 315... Forbidden Forbidden D 40
compressed.
Boron trifluoride 8 UN1742 II 8......... B2, B6, IB2, T8, 154........... 202........ 242........ 1 L 30 L A .......
acetic acid complex. TP2, TP12
Boron trifluoride 8 UN2604 I 8, 3...... A19, T10, TP2 None.......... 201........ 243........ 0.5 L 2.5 L D 40
diethyl etherate.
Boron trifluoride 8 UN2851 II 8......... IB8, IP2, IP4, 154........... 212........ 240........ 15 kg 50 kg B 12, 40,
dihydrate. T7, TP2
Boron trifluoride 4.3 UN2965 I 4.3, 8, 3. A19, T10, TP2, None.......... 201........ 243........ Forbidden 1 L D 21, 28,
dimethyl etherate. TP7 40, 49,
100
Boron trifluoride 8 UN1743 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L A .......
propionic acid TP2, TP12
complex.
Box toe gum, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Nitrocellulose etc.
Bromates, inorganic, 5.1 UN3213 II 5.1....... IB2, T4, TP1 152........... 202........ 242........ 1 L 5 L B 56, 58,
aqueous solution, 106
n.o.s..
Bromates, inorganic, 5.1 UN1450 II 5.1....... IB8, IP2, IP4 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
n.o.s.. 106
Bromine azide....... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
+ Bromine or Bromine 8 UN1744 I 8, 6.1.... 1, A3, A6, B9, None.......... 226........ 249........ Forbidden Forbidden ............ 12, 40,
solutions. B64, B85, N34, 66, 74,
N43, T22, TP2, 89, 90
TP10, TP12, TP13
Bromine chloride.... 2.3 UN2901 ....... 2.3, 8, 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40, 89,
5.1. 90
+ Bromine 5.1 UN1745 I 5.1, 6.1, 1, B9, B14, B30, None.......... 228........ 244........ Forbidden Forbidden D 25, 40,
pentafluoride. 8. B72, T22, TP2, 66, 90
TP12, TP13,
TP38, TP44
+ Bromine trifluoride. 5.1 UN1746 I 5.1, 6.1, 2, B9, B14, B32, None.......... 228........ 244........ Forbidden Forbidden D 25, 40,
8. B74, T22, TP2, 66, 90
TP12, TP13,
TP38, TP45
4-Bromo-1,2- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrobenzene.
4-Bromo-1,2- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrobenzene
(unstable at 59
degrees C.).
1-Bromo-3- 6.1 UN2688 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
chloropropane.
1-Bromo-3- 3 UN2341 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
methylbutane.
1-Bromo-3- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrobenzene
(unstable at 56
degrees C).
2-Bromo-2- 4.1 UN3241 III 4.1....... 46, IB8, IP3 151........... 213........ None....... 25 kg 50 kg C 12, 25,
nitropropane-1,3- 40
diol.
Bromoacetic acid, 8 UN1938 II 8......... A7, IB8, IP2, 154........... 212........ 240........ 15 kg 50 kg A .......
solid. IP4, N34, T7
Bromoacetic acid, 8 UN1938 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A 40
solution.
+ Bromoacetone........ 6.1 UN1569 II 6.1, 3.... 2, T20, TP2, None.......... 193........ 245........ Forbidden Forbidden D 40
TP13
Bromoacetyl bromide. 8 UN2513 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L C 40
TP2, TP12
[[Page 130]]
Bromobenzene........ 3 UN2514 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Bromobenzyl 6.1 UN1694 I 6.1....... T14, TP2, TP13 None.......... 201........ 243........ Forbidden 30 L D 12, 40
cyanides, liquid.
Bromobenzyl 6.1 UN1694 I 6.1....... T14, TP2, TP13 None.......... 211........ 242........ Forbidden 50 kg D 12, 40
cyanides, solid.
1-Bromobutane....... 3 UN1126 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5L 60 L B 40
2-Bromobutane....... 3 UN2339 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Bromochloromethane.. 6.1 UN1887 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
2-Bromoethyl ethyl 3 UN2340 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
ether.
Bromoform........... 6.1 UN2515 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A 12, 40
Bromomethylpropanes. 3 UN2342 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
2-Bromopentane...... 3 UN2343 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Bromopropanes....... 3 UN2344 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
.................... ........... .................. III 3......... IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
3-Bromopropyne...... 3 UN2345 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L D 40
Bromosilane......... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Bromotoluene-alpha, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Benzyl bromide.
Bromotrifluoroethyle 2.1 UN2419 ....... 2.1....... None.......... 304........ 314, 315... Forbidden 150 kg B 40
ne.
Bromotrifluoromethan 2.2 UN1009 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
e or Refrigerant
gas, R 13B1..
Brucine............. 6.1 UN1570 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A .......
Bursters, explosive. 1.1D UN0043 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Butadienes, 2.1 UN1010 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
stabilized.
Butane see also 2.1 UN1011 ....... 2.1....... 19, T50 306........... 304........ 314, 315... Forbidden 150 kg E 40
Petroleum gases,
liquefied.
Butane, butane ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures and
mixtures having
similar properties
in cartridges each
not exceeding 500
grams, see
Receptacles, etc.
Butanedione......... 3 UN2346 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
1,2,4-Butanetriol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
trinitrate.
Butanols............ 3 UN1120 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP29
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
tert-Butoxycarbonyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
azide.
Butyl acetates...... 3 UN1123 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 131]]
Butyl acid phosphate 8 UN1718 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Butyl acrylates, 3 UN2348 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
stabilized.
Butyl alcohols, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Butanols.
Butyl benzenes...... 3 UN2709 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
n-Butyl bromide, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
1-Bromobutane.
n-Butyl chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Chlorobutanes.
D sec-Butyl 6.1 NA2742 I 6.1, 3, 8. 2, B9, B14, B32, None.......... 227........ 244........ 1 L 30 L A 12, 13,
chloroformate. B74, T20, TP4, 22, 25,
TP12, TP13, 40, 48,
TP38, TP45 100
n-Butyl 6.1 UN2743 I 6.1, 8, 3. 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A 12, 13,
chloroformate. B74, T20, TP2, 21, 25,
TP13, TP38, TP45 40, 100
Butyl ethers, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Dibutyl ethers.
Butyl ethyl ether, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethyl butyl
ether.
n-Butyl formate..... 3 UN1128 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
tert-Butyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
hydroperoxide, with
more than 90
percent with water.
tert-Butyl 4.2 UN3255 I 4.2, 8.... None.......... 211........ 243........ Forbidden Forbidden D .......
hypochlorite.
N-n-Butyl imidazole. 6.1 UN2690 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
tert-Butyl 6.1 UN2484 I 6.1, 3.... 1, A7, B9, B14, None.......... 226........ 244........ Forbidden Forbidden D 40
isocyanate. B30, B72, T22,
TP2, TP13, TP38,
TP44
n-Butyl isocyanate.. 6.1 UN2485 I 6.1, 3.... 2, A7, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
B32, B74, B77,
T20, TP2, TP13,
TP38, TP45
Butyl mercaptans.... 3 UN2347 II 3......... A3, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L D 26, 95
n-Butyl 3 UN2227 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
methacrylate,
stabilized.
Butyl methyl ether.. 3 UN2350 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Butyl nitrites...... 3 UN2351 I 3......... T11, TP1, TP8, 150........... 201........ 243........ 1 L 30 L E 40
TP27
.................... ........... .................. II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A 40
tert-Butyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxyacetate, with
more than 76
percent in solution.
n-Butyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxydicarbonate,
with more than 52
percent in solution.
tert-Butyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxyisobutyrate,
with more than 77
percent in solution.
[[Page 132]]
Butyl phosphoric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
acid, see Butyl
acid phosphate.
Butyl propionates... 3 UN1914 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
5-tert-Butyl-2,4,6- 4.1 UN2956 III 4.1....... None.......... 214........ None....... Forbidden Forbidden D 12
trinitro-m-xylene
or Musk xylene.
Butyl vinyl ether, 3 UN2352 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
stabilized.
n-Butylamine........ 3 UN1125 II 3, 8...... IB2, T7, TP1 None.......... 202........ 242........ 1 L 5 L B 40
N-Butylaniline...... 6.1 UN2738 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
tert- 6.1 UN2747 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A 12, 13,
Butylcyclohexylchlo 25
roformate.
Butylene see also 2.1 UN1012 ....... 2.1....... 19, T50 None.......... 304........ 314, 315... Forbidden 150 kg E 40
Petroleum gases,
liquefied.
1,2-Butylene oxide, 3 UN3022 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 49
stabilized.
Butyltoluenes....... 6.1 UN2667 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Butyltrichlorosilane 8 UN1747 II 8, 3...... A7, B2, B6, IB2, None.......... 202........ 243........ Forbidden 30 L C 40
N34, T7, TP2,
TP13
1,4-Butynediol...... 6.1 UN2716 III 6.1....... A1, IB8, IP3 None.......... 213........ 240........ 100 kg 200 kg A 61, 70
Butyraldehyde....... 3 UN1129 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Butyraldoxime....... 3 UN2840 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Butyric acid........ 8 UN2820 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A 12
Butyric anhydride... 8 UN2739 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Butyronitrile....... 3 UN2411 II 3, 6.1.... IB2, T7, TP1, None.......... 202........ 243........ 1 L 60 L E 40
TP13
Butyryl chloride.... 3 UN2353 II 3, 8...... IB2, T8, TP2, None.......... 202........ 243........ 1 L 5 L C 40
TP12, TP13
Cacodylic acid...... 6.1 UN1572 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg E 26
Cadmium compounds... 6.1 UN2570 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A .......
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Caesium hydroxide... 8 UN2682 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
Caesium hydroxide 8 UN2681 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A .......
solution.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Calcium............. 4.3 UN1401 II 4.3....... IB7, IP2 151........... 212........ 241........ 15 kg 50 kg E .......
Calcium arsenate.... 6.1 UN1573 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Calcium arsenate and 6.1 UN1574 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
calcium arsenite,
mixtures, solid.
[[Page 133]]
Calcium bisulfite ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solution, see
Bisulfites, aqueous
solutions, n.o.s..
Calcium carbide..... 4.3 UN1402 I 4.3....... A1, A8, B55, None.......... 211........ 242........ Forbidden 15 kg B .......
B59, IB4, IP1,
N34
.................... ........... .................. II 4.3....... A1, A8, B55, 151........... 212........ 241........ 15 kg 50 kg B .......
B59, IB7, IP2,
N34
Calcium chlorate.... 5.1 UN1452 II 5.1....... IB8, IP2, IP4, 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
N34 106
Calcium chlorate 5.1 UN2429 II 5.1....... A2, IB2, N41, 152........... 202........ 242........ 1 L 5 L B 56, 58,
aqueous solution. T4, TP1 106
.................... ........... .................. III 5.1....... A2, IB2, N41, 152........... 203........ 241........ 2.5 L 30 L B 56, 68,
T4, TP1 106
Calcium chlorite.... 5.1 UN1453 II 5.1....... A9, IB8, IP2, 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
IP4, N34 106
Calcium cyanamide 4.3 UN1403 III 4.3....... A1, A19, IB8, 151........... 213........ 241........ 25 kg 100 kg A .......
with more than 0.1 IP4
percent of calcium
carbide.
Calcium cyanide..... 6.1 UN1575 I 6.1....... IB7, IP1, N79, None.......... 211........ 242........ 5 kg 50 kg A 26, 40
N80
Calcium dithionite 4.2 UN1923 II 4.2....... A19, A20, IB6, None.......... 212........ 241........ 15 kg 50 kg E 13
or Calcium IP2
hydrosulfite.
Calcium hydride..... 4.3 UN1404 I 4.3....... A19, N40 None.......... 211........ 242........ Forbidden 15 kg E .......
Calcium ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydrosulfite, see
Calcium dithionite.
Calcium 5.1 UN1748 II 5.1....... A7, A9, IB8, 152........... 212........ None....... 5 kg 25 kg D 4, 5,
hypochlorite, dry IP2, IP4, N34, 25, 48,
or Calcium W9 56, 58,
hypochlorite 69
mixtures dry with
more than 39
percent available
chlorine (8.8
percent available
oxygen).
Calcium 5.1 UN2880 II 5.1....... IB8, IP2, IP4, 152........... 212........ 240........ 5 kg 25 kg D 4, 5,
hypochlorite, W9 25, 48,
hydrated or Calcium 56, 58,
hypochlorite, 69
hydrated mixtures,
with not less than
5.5 percent but not
more than 10
percent water.
Calcium hypochlorite 5.1 UN2208 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg D 4, 5,
mixtures, dry, with IP3, N34, W9 25, 48,
more than 10 56, 58,
percent but not 69
more than 39
percent available
chlorine.
Calcium manganese 4.3 UN2844 III 4.3....... A1, A19, IB8, 151........... 213........ 241........ 25 kg 100 kg A 85, 103
silicon. IP2, IP4
Calcium nitrate..... 5.1 UN1454 III 5.1....... 34, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
A Calcium oxide....... 8 UN1910 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
Calcium perchlorate. 5.1 UN1455 II 5.1....... IB6, IP2 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
106
[[Page 134]]
Calcium permanganate 5.1 UN1456 II 5.1....... IB6, IP2 152........... 212........ 242........ 5 kg 25 kg D 56, 58,
69,
106,
107
Calcium peroxide.... 5.1 UN1457 II 5.1....... IB6, IP2 152........... 212........ 242........ 5 kg 25 kg A 13, 75,
106
Calcium phosphide... 4.3 UN1360 I 4.3, 6.1.. A8, A19, N40 None.......... 211........ 242........ Forbidden 15 kg E 40, 85
Calcium, pyrophoric 4.2 UN1855 I 4.2....... None.......... 187........ None....... Forbidden Forbidden D .......
or Calcium alloys,
pyrophoric.
Calcium resinate.... 4.1 UN1313 III 4.1....... A1, A19, IB6 None.......... 213........ 240........ 25 kg 100 kg A .......
Calcium resinate, 4.1 UN1314 III 4.1....... A1, A19, IB4 None.......... 213........ 240........ 25 kg 100 kg A .......
fused.
Calcium selenate, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Selenates or
Selenites.
Calcium silicide.... 4.3 UN1405 II 4.3....... A19, IB7, IP2 151........... 212........ 241........ 15 kg 50 kg B 85, 103
.................... ........... .................. III 4.3....... A1, A19, IB8, 151........... 213........ 241........ 25 kg 100 kg B 85, 103
IP4
Camphor oil......... 3 UN1130 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Camphor, synthetic.. 4.1 UN2717 III 4.1....... A1, IB8, IP3 None.......... 213........ 240........ 25 kg 100 kg A .......
Cannon primers, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Primers, tubular.
Caproic acid........ 8 UN2829 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Caps, blasting, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Detonators, etc.
Carbamate 3 UN2758 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L B 40
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Carbamate 6.1 UN2992 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Carbamate 6.1 UN2991 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic, flammable,
flash point not
less than 23
degrees C.
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
[[Page 135]]
.................... ........... .................. III 6.1, 3.... B1, IB3, T7, 153........... 203........ 242........ 60 L 220 L A 40
TP2, TP28
Carbamate 6.1 UN2757 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid,
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Carbolic acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Phenol, solid or
Phenol, molten.
Carbolic acid ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solutions, see
Phenol solutions.
I Carbon, activated... 4.2 UN1362 III 4.2....... IB8, IP3 None.......... 213........ 241........ 0.5 kg 0.5 kg A 12
I Carbon, animal or 4.2 UN1361 II 4.2....... IB6 None.......... 212........ 242........ Forbidden Forbidden A 12
vegetable origin.
.................... ........... .................. III 4.2....... IB8, IP3 None.......... 213........ 241........ Forbidden Forbidden A 12
Carbon bisulfide, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Carbon
disulfide.
Carbon dioxide...... 2.2 UN1013 ....... 2.2....... 306........... 302, 304... 302, 314, 75 kg 150 kg A .......
315.
Carbon dioxide and 2.2 UN1015 ....... 2.2....... 306........... None....... 314, 315... 75 kg 150 kg A .......
nitrous oxide
mixtures.
Carbon dioxide and 2.2 UN1014 ....... 2.2, 5.1.. 77 306........... 304........ 314, 315... 75 kg 150 kg A .......
oxygen mixtures,
compressed.
Carbon dioxide, 2.2 UN2187 ....... 2.2....... T75, TP5 306........... 304........ 314, 315... 50 kg 500 kg B .......
refrigerated liquid.
A W Carbon dioxide, 9 UN1845 III None...... 217........... 217........ 240........ 200 kg 200 kg C 40
solid or Dry ice.
Carbon disulfide.... 3 UN1131 I 3, 6.1.... B16, T14, TP2, None.......... 201........ 243........ Forbidden Forbidden D 18, 40,
TP7, TP13 115
Carbon monoxide, 2.3 UN1016 ....... 2.3, 2.1.. 4 None.......... 302........ 314, 315... Forbidden 25 kg D 40
compressed.
Carbon monoxide and 2.3 UN2600 ....... 2.3, 2.1.. 6 None.......... 302........ 302........ Forbidden Forbidden D 40
hydrogen mixture,
compressed.
D Carbon monoxide, 2.3 NA9202 ....... 2.3, 2.1.. 4, T75, TP5 None.......... 316........ 318........ Forbidden Forbidden D .......
refrigerated liquid
(cryogenic liquid).
Carbon tetrabromide. 6.1 UN2516 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 25
Carbon tetrachloride 6.1 UN1846 II 6.1....... IB2, N36, T7, None.......... 202........ 243........ 5 L 60 L A 40
TP2
Carbonyl chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Phosgene.
Carbonyl fluoride, 2.3 UN2417 ....... 2.3, 8.... 2 None.......... 302........ None....... Forbidden Forbidden D 40
compressed.
Carbonyl sulfide.... 2.3 UN2204 ....... 2.3, 2.1.. 3, B14 None.......... 304........ 314, 315... Forbidden 25 kg D 40
Cartridge cases, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
empty primed, see
Cases, cartridge,
empty, with primer.
Cartridges, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
actuating, for
aircraft ejector
seat catapult, fire
extinguisher,
canopy removal or
apparatus, see
Cartridges, power
device.
[[Page 136]]
Cartridges, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
explosive, see
Charges, demolition.
Cartridges, flash... 1.1G UN0049 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Cartridges, flash... 1.3G UN0050 II 1.3G...... None.......... 62......... None....... Forbidden 75 kg 07 .......
Cartridges for 1.1C UN0326 II 1.1C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
weapons, blank.
Cartridges for 1.2C UN0413 II 1.2C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
weapons, blank.
Cartridges for 1.4S UN0014 II None...... 63............ 62......... None....... 25 kg 100 kg 05 .......
weapons, blank or
Cartridges, small
arms, blank.
Cartridges for 1.3C UN0327 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
weapons, blank or
Cartridges, small
arms, blank.
Cartridges for 1.4C UN0338 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 06 .......
weapons, blank or
Cartridges, small
arms, blank.
Cartridges for 1.2C UN0328 II 1.2C...... None.......... 62......... None....... Forbidden Forbidden 03 .......
weapons, inert
projectile.
Cartridges for 1.4S UN0012 II None...... 63............ 62......... None....... 25 kg 100 kg 05 .......
weapons, inert
projectile or
Cartridges, small
arms.
Cartridges for 1.4C UN0339 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 06 .......
weapons, inert
projectile or
Cartridges, small
arms.
Cartridges for 1.3C UN0417 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 06 .......
weapons, inert
projectile or
Cartridges, small
arms.
Cartridges for 1.1F UN0005 II 1.1F...... None.......... 62......... None....... Forbidden Forbidden 08 .......
weapons, with
bursting charge.
Cartridges for 1.1E UN0006 II 1.1E...... None.......... 62......... None....... Forbidden Forbidden 03 .......
weapons, with
bursting charge.
Cartridges for 1.2F UN0007 II 1.2F...... None.......... 62......... None....... Forbidden Forbidden 08 .......
weapons, with
bursting charge.
Cartridges for 1.2E UN0321 II 1.2E...... None.......... 62......... None....... Forbidden Forbidden 03 .......
weapons, with
bursting charge.
Cartridges for 1.4F UN0348 II 1.4F...... None.......... 62......... None....... Forbidden Forbidden 08 .......
weapons, with
bursting charge.
Cartridges for 1.4E UN0412 II 1.4E...... None.......... 62......... None....... Forbidden 75 kg 02 .......
weapons, with
bursting charge.
Cartridges, oil well 1.3C UN0277 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Cartridges, oil well 1.4C UN0278 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Cartridges, power 1.3C UN0275 II 1.3C...... None.......... 62......... None....... Forbidden 75 kg 07 .......
device.
Cartridges, power 1.4C UN0276 II 1.4C...... 110 None.......... 62......... None....... Forbidden 75 kg 06 .......
device.
[[Page 137]]
Cartridges, power 1.4S UN0323 II 1.4S...... 110 63............ 62......... None....... 25 kg 100 kg 05 .......
device.
Cartridges, power 1.2C UN0381 II 1.2C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
device.
Cartridges, safety, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
blank, see
Cartridges for
weapons, blank (UN
0014).
Cartridges, safety, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Cartridges for
weapons, other than
blank or
Cartridges, power
device (UN 0323).
Cartridges, signal.. 1.3G UN0054 II 1.3G...... None.......... 62......... None....... Forbidden 75 kg 07 .......
Cartridges, signal.. 1.4G UN0312 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Cartridges, signal.. 1.4S UN0405 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
D Cartridges, small ORM-D .................. ....... None...... 63............ None....... None....... 30 kg gross 30 kg gross A .......
arms.
Cartridges, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
sporting, see
Cartridges for
weapons, other than
blank.
Cartridges, starter, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
jet engine, see
Cartridges, power
device.
Cases, cartridge, 1.4S UN0055 II 1.4S...... 50 None.......... 62......... None....... 25 kg 100 kg 05 .......
empty with primer.
Cases, cartridges, 1.4C UN0379 II 1.4C...... 50 None.......... 62......... None....... Forbidden 75 kg 06 .......
empty with primer.
Cases, combustible, 1.4C UN0446 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 06 .......
empty, without
primer.
Cases, combustible, 1.3C UN0447 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
empty, without
primer.
Casinghead gasoline ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Gasoline.
A W Castor beans or 9 UN2969 II None...... IB8, IP2, IP4 155........... 204........ 240........ No limit No limit E 34, 40
Castor meal or
Castor pomace or
Castor flake.
G Caustic alkali 8 UN1719 II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L A .......
liquids, n.o.s.. TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A .......
TP28
Caustic potash, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Potassium hydroxide
etc.
Caustic soda, (etc.) ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Sodium
hydroxide etc.
Cells, containing 4.3 UN3292 II 4.3....... 189........... 189........ 189........ 25 kg gross No limit A .......
sodium.
Celluloid, in block, 4.1 UN2000 III 4.1....... None.......... 213........ 240........ 25 kg 100 kg A .......
rods, rolls,
sheets, tubes,
etc., except scrap.
Celluloid, scrap.... 4.2 UN2002 III 4.2....... IB8, IP3 None.......... 213........ 241........ Forbidden Forbidden D .......
Cement, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Adhesives
containing
flammable liquid.
Cerium, slabs, 4.1 UN1333 II 4.1....... IB8, IP2, IP4, None.......... 212........ 240........ 15 kg 50 kg A 74, 91
ingots, or rods. N34
Cerium, turnings or 4.3 UN3078 II 4.3....... A1, IB7, IP2 151........... 212........ 242........ 15 kg 50 kg E .......
gritty powder.
[[Page 138]]
Cesium or Caesium... 4.3 UN1407 I 4.3....... A19, IB1, IP1, None.......... 211........ 242........ Forbidden 15 kg D .......
N34, N40
Cesium nitrate or 5.1 UN1451 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A .......
Caesium nitrate. IP3
D Charcoal briquettes, 4.2 NA1361 III 4.2....... IB8 151........... 213........ 240........ 25 kg 100 kg A 12
shell, screenings,
wood, etc..
Charges, bursting, 1.1D UN0457 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
plastics bonded.
Charges, bursting, 1.2D UN0458 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
plastics bonded.
Charges, bursting, 1.4D UN0459 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
plastics bonded.
Charges, bursting, 1.4S UN0460 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
plastics bonded.
Charges, demolition. 1.1D UN0048 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 03 .......
Charges, depth...... 1.1D UN0056 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 03 .......
Charges, expelling, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
explosive, for fire
extinguishers, see
Cartridges, power
device.
Charges, explosive, 1.1D UN0442 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
commercial without
detonator.
Charges, explosive, 1.2D UN0443 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
commercial without
detonator.
Charges, explosive, 1.4D UN0444 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
commercial without
detonator.
Charges, explosive, 1.4S UN0445 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
commercial without
detonator.
Charges, propelling. 1.1C UN0271 II 1.1C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Charges, propelling. 1.3C UN0272 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Charges, propelling. 1.2C UN0415 II 1.2C...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Charges, propelling. 1.4C UN0491 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Charges, propelling, 1.3C UN0242 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 10 .......
for cannon.
Charges, propelling, 1.1C UN0279 II 1.1C...... None.......... 62......... None....... Forbidden Forbidden 10 .......
for cannon.
Charges, propelling, 1.2C UN0414 II 1.2C...... None.......... 62......... None....... Forbidden Forbidden 10 .......
for cannon.
Charges, shaped, 1.4D UN0237 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
flexible, linear.
Charges, shaped, 1.1D UN0288 II 1.1D...... 101 None.......... 62......... None....... Forbidden Forbidden 07 .......
flexible, linear.
Charges, shaped, 1.1D UN0059 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
without detonator.
[[Page 139]]
Charges, shaped, 1.2D UN0439 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
without detonator.
Charges, shaped, 1.4D UN0440 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
without detonator.
Charges, shaped, 1.4S UN0441 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
without detonator.
Charges, 1.1D UN0060 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
supplementary
explosive.
D Chemical kit........ 8 NA1760 II 8......... 154........... 161........ None....... 1 L 30 L B 40
Chemical kits....... 9 UN3316 ....... 9......... 15 None.......... None....... None....... 10 kg 10 kg A .......
Chloral, anhydrous, 6.1 UN2075 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L D 40
stabilized.
Chlorate and borate 5.1 UN1458 II 5.1....... A9, IB8, IP2, 152........... 212........ 240........ 5 kg 25 kg A 56, 58,
mixtures. IP4, N34 106
.................... ........... .................. III 5.1....... A9, IB8, IP3, 152........... 213........ 240........ 25 kg 100 kg A 56, 58,
N34 106
Chlorate and 5.1 UN1459 II 5.1....... A9, IB8, IP2, 152........... 212........ 240........ 5 kg 25 kg A 56, 58,
magnesium chloride IP4, N34, T4, 106
mixtures. TP1
.................... ........... .................. III 5.1....... A9, IB8, IP3, 152........... 213........ 240........ 25 kg 100 kg A 56, 58,
N34, T4, TP1 106
Chlorate of potash, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Potassium
chlorate.
Chlorate of soda, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Sodium chlorate.
Chlorates, 5.1 UN3210 II 5.1....... IB2, T4, TP1 152........... 202........ 242........ 1 L 5 L B 56, 58,
inorganic, aqueous 106
solution, n.o.s..
Chlorates, 5.1 UN1461 II 5.1....... A9, IB6, IP2, 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
inorganic, n.o.s.. N34 106
Chloric acid aqueous 5.1 UN2626 II 5.1....... IB2 None.......... 229........ None....... Forbidden Forbidden D 56, 58,
solution, with not 106
more than 10
percent chloric
acid.
Chloride of ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
phosphorus, see
Phosphorus
trichloride.
Chloride of sulfur, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Sulfur chloride.
Chlorinated lime, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Calcium
hypochlorite
mixtures, etc.
Chlorine............ 2.3 UN1017 ....... 2.3, 8.... 2, B9, B14, T50, None.......... 304........ 314, 315... Forbidden Forbidden D 40, 51,
TP19 55, 62,
68, 89,
90
Chlorine azide...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
D Chlorine dioxide, 5.1 NA9191 II 5.1, 6.1.. None.......... 229........ None....... Forbidden Forbidden E .......
hydrate, frozen.
Chlorine dioxide Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(not hydrate).
Chlorine 2.3 UN2548 ....... 2.3, 5.1, 1, B7, B9, B14 None.......... 304........ 314........ Forbidden Forbidden D 40, 89,
pentafluoride. 8. 90
Chlorine trifluoride 2.3 UN1749 ....... 2.3, 5.1, 2, B7, B9, B14 None.......... 304........ 314........ Forbidden Forbidden D 40, 89,
8. 90
[[Page 140]]
Chlorite solution... 8 UN1908 II 8......... A3, A6, A7, B2, 154........... 202........ 242........ 1 L 30 L B 26
IB2, N34, T7,
TP2, TP24
.................... ........... .................. III 8......... A3, A6, A7, B2, 154........... 203........ 241........ 5 L 60 L B 26
IB3, N34, T4,
TP2, TP24
Chlorites, 5.1 UN1462 II 5.1....... A7, IB6, IP2, 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
inorganic, n.o.s.. N34 106
1-Chloro-1,1- 2.1 UN2517 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
difluoroethane or
Refrigerant gas R
142b.
3-Chloro-4- 6.1 UN2236 II 6.1....... IB2 None.......... 202........ 243........ 5 L 60 L B 40
methylphenyl
isocyanate.
1-Chloro-1,2,2,2- 2.2 UN1021 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
tetrafluoroethaneor
Refrigerant gas R
124.
4-Chloro-o-toluidine 6.1 UN1579 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
hydrochloride.
1-Chloro-2,2,2- 2.2 UN1983 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
trifluoroethane or
Refrigerant gas R
133a.
Chloroacetic acid, 6.1 UN3250 II 6.1, 8.... IB1, T7, TP3 None.......... 202........ 243........ Forbidden Forbidden C 40
molten.
Chloroacetic acid, 6.1 UN1751 II 6.1, 8.... A3, A7, IB8, None.......... 212........ 242........ 15 kg 50 kg A 40
solid. IP4, N34
Chloroacetic acid, 6.1 UN1750 II 6.1, 8.... A7, IB2, N34, None.......... 202........ 243........ 1 L 30 L C 40
solution. T7, TP2
Chloroacetone, 6.1 UN1695 I 6.1, 3, 8. 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 21, 40,
stabilized. B74, N12, N32, 100
N34, T20, TP2,
TP13, TP38, TP45
Chloroacetone Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(unstabilized).
+ Chloroacetonitrile.. 6.1 UN2668 II 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A 12, 26,
B74, IB99, T20, 40
TP2, TP38, TP45
Chloroacetophenone 6.1 UN1697 II 6.1....... A3, IB2, N12, None.......... 202........ 243........ Forbidden 60 L D 12, 40
(CN), liquid. N32, N33, T11,
TP2, TP13, TP27
[[Page 141]]
Chloroacetophenone 6.1 UN1697 II 6.1....... A3, IB8, IP2, None.......... 212........ None....... Forbidden 100 kg D 12, 40
(CN), solid. IP4, N12, N32,
N33, N34, T7,
TP2, TP13
Chloroacetyl 6.1 UN1752 I 6.1, 8.... 2, A3, A6, A7, None.......... 227........ 244........ Forbidden Forbidden D 40
chloride. B3, B8, B9, B14,
B32, B74, B77,
N34, N43, T20,
TP2, TP13, TP38,
TP45
Chloroanilines, 6.1 UN2019 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
liquid.
Chloroanilines, 6.1 UN2018 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......
solid. T7, TP2
Chloroanisidines.... 6.1 UN2233 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Chlorobenzene....... 3 UN1134 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Chlorobenzol, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Chlorobenzene.
Chlorobenzotrifluori 3 UN2234 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A 40
des.
Chlorobenzyl 6.1 UN2235 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
chlorides.
Chlorobutanes....... 3 UN1127 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Chlorocresols, 6.1 UN2669 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 12
liquid.
Chlorocresols, solid 6.1 UN2669 II 6.1....... IB8, IP2, IP3, None.......... 212........ 242........ 25 kg 100 kg A 12
T7
Chlorodifluorobromom 2.2 UN1974 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
ethane or
Refrigerant gas R
12B1.
Chlorodifluoromethan 2.2 UN1973 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
e and
chloropentafluoroet
hane mixture or
Refrigerant gas R
502 with fixed
boiling point, with
approximately 49
percent
chlorodifluorometha
ne.
Chlorodifluoromethan 2.2 UN1018 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
e or Refrigerant
gas R 22.
+ Chlorodinitrobenzene 6.1 UN1577 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 91
s. T7, TP2
2-Chloroethanal..... 6.1 UN2232 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, T20, TP2,
TP13, TP38, TP45
Chloroform.......... 6.1 UN1888 III 6.1....... IB3, N36, T7, 153........... 203........ 241........ 60 L 220 L A 40
TP2
G Chloroformates, 6.1 UN2742 II 6.1, 8, 3. 5, IB1, T7, TP2 None.......... 202........ 243........ 1 L 30 L A 12, 13,
toxic, corrosive, 21, 25,
flammable, n.o.s.. 40, 100
G Chloroformates, 6.1 UN3277 II 6.1, 8.... IB2, T8, TP2, None.......... 202........ 243........ 1 L 30 L A 12, 13,
toxic, corrosive, TP13, TP28 25, 40
n.o.s..
Chloromethyl 6.1 UN2745 II 6.1, 8.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 30 L A 12, 13,
chloroformate. TP13 21, 25,
40, 100
Chloromethyl ethyl 3 UN2354 II 3, 6.1.... IB2, T7, TP1, None.......... 202........ 243........ 1 L 60 L E 40
ether. TP13
[[Page 142]]
Chloronitroanilines. 6.1 UN2237 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
+ Chloronitrobenzene, 6.1 UN1578 II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L A .......
ortho, liquid. TP13, TP27
+ Chloronitrobenzenes 6.1 UN1578 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......
meta or para, solid. T7, TP2
Chloronitrotoluenes, 6.1 UN2433 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
liquid.
Chloronitrotoluenes, 6.1 UN2433 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
solid.
Chloropentafluoroeth 2.2 UN1020 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
ane or Refrigerant
gas R 115.
Chlorophenolates, 8 UN2904 III 8......... IB3 154........... 203........ 241........ 5 L 60 L A .......
liquid or
Phenolates, liquid.
Chlorophenolates, 8 UN2905 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
solid or
Phenolates, solid.
Chlorophenols, 6.1 UN2021 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
liquid.
Chlorophenols, solid 6.1 UN2020 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A .......
TP1
Chlorophenyltrichlor 8 UN1753 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
osilane. N34, T7, TP2
+ Chloropicrin........ 6.1 UN1580 I 6.1....... 2, B7, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
B32, B46, B74,
T20, TP2, TP13,
TP38, TP45
Chloropicrin and 2.3 UN1581 ....... 2.3....... 2, B9, B14, T50 None.......... 193........ 314, 315... Forbidden Forbidden D 25, 40
methyl bromide
mixtures.
Chloropicrin and 2.3 UN1582 ....... 2.3....... 2, T50 None.......... 193........ 245........ Forbidden Forbidden D 25, 40
methyl chloride
mixtures.
Chloropicrin ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixture, flammable
(pressure not
exceeding 14.7 psia
at 115 degrees F
flash point below
100 degrees F) see
Toxic liquids,
flammable, etc.
Chloropicrin 6.1 UN1583 I 6.1....... 5 None.......... 201........ 243........ Forbidden Forbidden C 40
mixtures, n.o.s..
.................... ........... .................. II 6.1....... IB2 None.......... 202........ 243........ Forbidden Forbidden C 40
.................... ........... .................. III 6.1....... IB3 153........... 203........ 241........ Forbidden Forbidden C 40
D Chloropivaloyl 6.1 NA9263 I 6.1, 8.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden B 40
chloride. B74, T20, TP4,
TP12, TP13,
TP38, TP45
Chloroplatinic acid, 8 UN2507 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
solid.
[[Page 143]]
Chloroprene, 3 UN1991 I 3, 6.1.... B57, T14, TP2, None.......... 201........ 243........ Forbidden 30 L D 40
stabilized. TP13
Chloroprene, Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
uninhibited.
2-Chloropropane..... 3 UN2356 I 3......... N36, T11, TP2, 150........... 201........ 243........ 1 L 30 L E .......
TP13
3-Chloropropanol-1.. 6.1 UN2849 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
2-Chloropropene..... 3 UN2456 I 3......... A3, N36, T11, 150........... 201........ 243........ 1 L 30 L E .......
TP2
2-Chloropropionic 8 UN2511 III 8......... IB3, T4, TP2 154........... 203........ 241........ 5 L 60 L A 8
acid.
2-Chloropyridine.... 6.1 UN2822 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 40
Chlorosilanes, 8 UN2986 II 8, 3...... IB2, T11, TP2, None.......... 202........ 243........ 1 L 30 L C 40
corrosive, TP27
flammable, n.o.s..
Chlorosilanes, 8 UN2987 II 8......... B2, IB2, T14, 154........... 202........ 242........ 1 L 30 L C 40
corrosive, n.o.s.. TP2, TP27
Chlorosilanes, 3 UN2985 II 3, 8...... IB1, T11, TP2, None.......... 201........ 243........ 1 L 5 L B 40
flammable, TP13, TP27
corrosive, n.o.s..
Chlorosilanes, water- 4.3 UN2988 I 4.3, 3, 8. A2, T10, TP2, None.......... 201........ 244........ Forbidden 1 L D 21, 28,
reactive, TP7, TP13 40, 49,
flammable, 100
corrosive, n.o.s..
+ Chlorosulfonic acid 8 UN1754 I 8, 6.1.... 2, A3, A6, A10, None.......... 227........ 244........ Forbidden Forbidden C 40
(with or without B9, B10, B14,
sulfur trioxide). B32, B74, T20,
TP2, TP12, TP38,
TP45
Chlorotoluenes...... 3 UN2238 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Chlorotoluidines 6.1 UN2239 III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A .......
liquid. TP28
Chlorotoluidines 6.1 UN2239 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A .......
solid. TP1
Chlorotrifluorometha 2.2 UN2599 ....... 2.2....... 306........... 304........ 314, 315... 75 kg 150 kg A .......
ne and
trifluoromethane
azeotropic mixture
or Refrigerant gas
R 503 with
approximately 60
percent
chlorotrifluorometh
ane.
Chlorotrifluorometha 2.2 UN1022 ....... 2.2....... 306........... 304........ 314, 315... 75 kg 150 kg A .......
ne or Refrigerant
gas R 13.
Chromic acid 8 UN1755 II 8......... B2, IB2, T8, 154........... 202........ 242........ 1 L 30 L C 40
solution. TP2, TP12
.................... ........... .................. III 8......... IB3, T4, TP1, 154........... 203........ 241........ 5 L 60 L C 40
TP12
Chromic anhydride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Chromium
trioxide, anhydrous.
Chromic fluoride, 8 UN1756 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A 26
solid.
Chromic fluoride, 8 UN1757 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A .......
solution.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Chromium nitrate.... 5.1 UN2720 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A .......
IP3
Chromium oxychloride 8 UN1758 I 8......... A3, A6, A7, B10, None.......... 201........ 243........ 0.5 L 2.5 L C 40, 66,
N34, T10, TP2, 74, 89,
TP12 90
Chromium trioxide, 5.1 UN1463 II 5.1, 8.... IB8, IP4 None.......... 212........ 242........ 5 kg 25 kg A .......
anhydrous.
[[Page 144]]
Chromosulfuric acid. 8 UN2240 I 8......... A3, A6, A7, B4, None.......... 201........ 243........ 0.5 L 2.5 L B 40, 66,
B6, N34, T10, 74, 89,
TP2, TP12, TP13 90
Chromyl chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Chromium
oxychloride.
Cigar and cigarette ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
lighters, charged
with fuel, see
Lighters for
cigars, cigarettes,
etc.
Coal briquettes, hot Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Coal gas, compressed 2.3 UN1023 ....... 2.3, 2.1.. 3 None.......... 302........ 314, 315... Forbidden 25 kg D 40
Coal tar 3 UN1136 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
distillates,
flammable.
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
Coal tar dye, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
corrosive, liquid,
n.o.s, see Dyes,
liquid or solid,
n.o.s. or Dye
intermediates,
liquid or solid,
corrosive, n.o.s..
Coating solution 3 UN1139 I 3......... T11, TP1, TP8, 150........... 201........ 243........ 1 L 30 L E .......
(includes surface TP27
treatments or
coatings used for
industrial or other
purposes such as
vehicle
undercoating, drum
or barrel lining).
.................... ........... .................. II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cobalt naphthenates, 4.1 UN2001 III 4.1....... A19, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A .......
powder.
Cobalt resinate, 4.1 UN1318 III 4.1....... A1, A19, IB6 151........... 213........ 240........ 25 kg 100 kg A .......
precipitated.
Coke, hot........... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Collodion, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Nitrocellulose etc.
D G Combustible liquid, Combustible NA1993 III None...... IB3,T1, T4, TP1 150........... 203........ 241........ 60 L 220 L A .......
n.o.s..
G Components, 1.2B UN0382 II 1.2B...... 101 None.......... 62......... None....... Forbidden Forbidden 11 .......
explosive train,
n.o.s..
G Components, 1.4B UN0383 II 1.4B...... 101 None.......... 62......... None....... Forbidden 75 kg 06 .......
explosive train,
n.o.s..
G Components, 1.4S UN0384 II 1.4S...... 101 None.......... 62......... None....... 25 kg 100 kg 05 .......
explosive train,
n.o.s..
[[Page 145]]
G Components, 1.1B UN0461 II 1.1B...... 101 None.......... 62......... None....... Forbidden Forbidden 11 .......
explosive train,
n.o.s..
Composition B, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexolite, etc.
D G Compounds, cleaning 8 NA1760 I 8......... A7, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L B 40
liquid. TP2, TP9, TP27
.................... ........... .................. II 8......... B2, IB2, N37, 154........... 202........ 242........ 1 L 30 L B 40
T11, TP2, TP27
.................... ........... .................. III 8......... IB3, N37, T7, 154........... 203........ 241........ 5 L 60 L A 40
TP1, TP28
D G Compounds, cleaning 3 NA1993 I 3......... T11, TP1, TP9 150........... 201........ 243........ 1 L 30 L E .......
liquid.
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, B52, IB3, 150........... 203........ 242........ 60 L 220 L A .......
T4, TP1, TP29
D G Compounds, tree 8 NA1760 I 8......... A7, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L B 40
killing, liquid or TP2, TP9, TP27
Compounds, weed
killing, liquid.
.................... ........... .................. II 8......... B2, IB2, N37, 154........... 202........ 242........ 1 L 30 L B 40
T11, TP2, TP27
.................... ........... .................. III 8......... IB3, N37, T7, 154........... 203........ 241........ 5 L 60 L A 40
TP1, TP28
D G Compounds, tree 3 NA1993 I 3......... T11, TP1, TP9 150........... 201........ 243........ 1 L 30 L E .......
killing, liquid or
Compounds, weed
killing, liquid.
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, B52, IB3, 150........... 203........ 242........ 60 L 220 L A .......
T4, TP1, TP29
D G Compounds, tree 6.1 NA2810 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
killing, liquid or TP27
Compounds, weed
killing, liquid.
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP27
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A 40
TP28
G Compressed gas, 2.1 UN1954 ....... 2.1....... 306........... 302, 305... 314, 315... Forbidden 150 kg D 40
flammable, n.o.s..
G Compressed gas, 2.2 UN1956 ....... 2.2....... 306, 307...... 302, 305... 314, 315... 75 kg 150 kg A .......
n.o.s..
G Compressed gas, 2.2 UN3156 ....... 2.2, 5.1.. 306........... 302........ 314, 315... 75 kg 150 kg D .......
oxidizing, n.o.s..
G I Compressed gas, 2.3 UN3304 ....... 2.3, 8.... 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone A.
G I Compressed gas, 2.3 UN3304 ....... 2.3, 8.... 2 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone B.
G I Compressed gas, 2.3 UN3304 ....... 2.3, 8.... 3 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone C.
[[Page 146]]
G I Compressed gas, 2.3 UN3304 ....... 2.3, 8.... 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone D.
G I Compressed gas, 2.3 UN3305 ....... 2.3, 2.1, 1 None.......... 192........ 245........ Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone A.
G I Compressed gas, 2.3 UN3305 ....... 2.3, 2.1, 2 None.......... 302, 305... 314, 315... Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone B.
G I Compressed gas, 2.3 UN3305 ....... 2.3, 2.1, 3 None.......... 302, 305... 314, 315... Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone C.
G I Compressed gas, 2.3 UN3305 ....... 2.3, 2.1, 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone D.
G Compressed gas, 2.3 UN1953 ....... 2.3, 2.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
hazard Zone A.
G Compressed gas, 2.3 UN1953 ....... 2.3, 2.1.. 2, B9, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
hazard Zone B.
G Compressed gas, 2.3 UN1953 ....... 2.3, 2.1.. 3, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone C.
G Compressed gas, 2.3 UN1953 ....... 2.3, 2.1.. 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone D.
G Compressed gas, 2.3 UN1955 ....... 2.3....... 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone A.
G Compressed gas, 2.3 UN1955 ....... 2.3....... 2, B9, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone B.
G Compressed gas, 2.3 UN1955 ....... 2.3....... 3, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone C.
G Compressed gas, 2.3 UN1955 ....... 2.3....... 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone D.
G I Compressed gas, 2.3 UN3306 ....... 2.3, 5.1, 1 None.......... 192........ 244........ Forbidden Forbidden D 40, 89,
toxic, oxdizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone A.
[[Page 147]]
G I Compressed gas, 2.3 UN3306 ....... 2.3, 5.1, 2 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone B.
G I Compressed gas, 2.3 UN3306 ....... 2.3, 5.1, 3 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone C.
G I Compressed gas, 2.3 UN3306 ....... 2.3, 5.1, 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone D.
G Compressed gas, 2.3 UN3303 ....... 2.3, 5.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone A.
G Compressed gas, 2.3 UN3303 ....... 2.3, 5.1.. 2 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone B.
G Compressed gas, 2.3 UN3303 ....... 2.3, 5.1.. 3 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone C.
G Compressed gas, 2.3 UN3303 ....... 2.3, 5.1.. 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone D.
D Consumer commodity.. ORM-D .................. ....... None...... 156, 306...... 156, 306... None....... 30 kg gross 30 kg gross A .......
Contrivances, water- 1.2L UN0248 II 1.2L...... 101 None.......... 62......... None....... Forbidden Forbidden 08 8E,
activated, with 14E,
burster, expelling 15E,
charge or 17E
propelling charge.
Contrivances, water- 1.3L UN0249 II 1.3L...... 101 None.......... 62......... None....... Forbidden Forbidden 08 8E,
activated, with 14E,
burster, expelling 15E,
charge or 17E
propelling charge.
Copper acetoarsenite 6.1 UN1585 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Copper acetylide.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Copper amine azide.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Copper arsenite..... 6.1 UN1586 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Copper based 3 UN2776 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L B 40
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Copper based 6.1 UN3010 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Copper based 6.1 UN3009 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic, flammable
flash point not
less than 23
degrees C.
[[Page 148]]
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1, 3.... B1, IB3, T7, 153........... 203........ 242........ 60 L 220 L A 40
TP2, TP28
Copper based 6.1 UN2775 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid,
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Copper chlorate..... 5.1 UN2721 II 5.1....... A1, IB8, IP2, 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
IP4 106
Copper chloride..... 8 UN2802 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
Copper cyanide...... 6.1 UN1587 II 6.1....... IB8, IP2, IP4 None.......... 204........ 242........ 25 kg 100 kg A 26
Copper selenate, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Selenates or
Selenites.
Copper selenite, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Selenates or
Selenites.
Copper tetramine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrate.
A W Copra............... 4.2 UN1363 III 4.2....... IB8, IP3, IP6 None.......... 213........ 241........ Forbidden Forbidden A 13, 19,
48, 119
Cord, detonating, 1.1D UN0065 II 1.1D...... 102 63(a)......... 62......... None....... Forbidden Forbidden 07 .......
flexible.
Cord, detonating, 1.4D UN0289 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
flexible.
Cord detonating or 1.2D UN0102 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Fuse detonating
metal clad.
Cord, detonating or 1.1D UN0290 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Fuse, detonating
metal clad.
Cord, detonating, 1.4D UN0104 II 1.4D...... None.......... 62......... None....... Forbidden 75 kg 06 .......
mild effect or
Fuse, detonating,
mild effect metal
clad.
Cord, igniter....... 1.4G UN0066 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Cordeau detonant ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
fuse, see Cord,
detonating, etc;
Cord, detonating,
flexible.
Cordite, see Powder, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
smokeless.
G Corrosive liquid, 8 UN3264 I 8......... B10, T14, TP2, None.......... 201........ 243........ 0.5 L 2.5 L B 40
acidic, inorganic, TP27
n.o.s..
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 40
TP28
[[Page 149]]
G Corrosive liquid, 8 UN3265 I 8......... B10, T14, TP2, None.......... 201........ 243........ 0.5 L 2.5 L B 40
acidic, organic, TP27
n.o.s..
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 40
TP28
G Corrosive liquid, 8 UN3266 I 8......... B10, T14, TP2, None.......... 201........ 243........ 0.5 L 2.5 L B 40
basic, inorganic, TP27
n.o.s..
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 40
TP28
G Corrosive liquid, 8 UN3267 I 8......... B10, T14, TP2, None.......... 201........ 243........ 0.5 L 2.5 L B 40
basic, organic, TP27
n.o.s..
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 40
TP28
G Corrosive liquid, 8 UN3301 I 8, 4.2.... B10 None.......... 201........ 243........ 0.5 L 2.5 L D .......
self-heating,
n.o.s..
.................... ........... .................. II 8, 4.2.... B2, IB1 154........... 202........ 242........ 1 L 30 L D .......
G Corrosive liquids, 8 UN2920 I 8, 3...... B10, T14, TP2, None.......... 201........ 243........ 0.5 L 2.5 L C 25, 40
flammable, n.o.s.. TP27
.................... ........... .................. II 8, 3...... B2, IB2, T11, None.......... 202........ 243........ 1 L 30 L C 25, 40
TP2, TP27
G Corrosive liquids, 8 UN1760 I 8......... A7, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L B 40
n.o.s.. TP2, TP27
.................... ........... .................. II 8......... B2, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
TP2, TP27
.................... ........... .................. III 8......... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L A 40
TP28
G Corrosive liquids, 8 UN3093 I 8, 5.1.... None.......... 201........ 243........ Forbidden 2.5 L C 89
oxidizing, n.o.s..
.................... ........... .................. II 8, 5.1.... IB2 None.......... 202........ 243........ 1 L 30 L C 89
G Corrosive liquids, 8 UN2922 I 8, 6.1.... A7, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L B 40
toxic, n.o.s.. TP2, TP13, TP27
.................... ........... .................. II 8, 6.1.... B3, IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L B 40
.................... ........... .................. III 8, 6.1.... IB3, T7, TP1, 154........... 203........ 241........ 5 L 60 L B 40
TP28
G Corrosive liquids, 8 UN3094 I 8, 4.3.... None.......... 201........ 243........ Forbidden 1 L E .......
water-reactive,
n.o.s..
.................... ........... .................. II 8, 4.3.... None.......... 202........ 243........ 1 L 5 L E .......
G Corrosive solid, 8 UN3260 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg B .......
acidic, inorganic,
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg B .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
G Corrosive solid, 8 UN3261 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg B .......
acidic, organic,
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg B .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
[[Page 150]]
G Corrosive solid, 8 UN3262 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg B .......
basic, inorganic,
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg B .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
G Corrosive solid, 8 UN3263 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg B .......
basic, organic,
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg B .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
G Corrosive solids, 8 UN2921 I 8, 4.1.... IB6 None.......... 211........ 242........ 1 kg 25 kg B 12, 25
flammable, n.o.s..
.................... ........... .................. II 8, 4.1.... IB8, IP2, IP4 None.......... 212........ 242........ 15 kg 50 kg B 12, 25
G Corrosive solids, 8 UN1759 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg B .......
n.o.s..
.................... ........... .................. II 8......... 128, IB8, IP2, 154........... 212........ 240........ 15 kg 50 kg A .......
IP4
.................... ........... .................. III 8......... 128, IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
G Corrosive solids, 8 UN3084 I 8, 5.1.... None.......... 211........ 242........ 1 kg 25 kg C .......
oxidizing, n.o.s..
.................... ........... .................. II 8, 5.1.... IB6, IP2 None.......... 212........ 242........ 15 kg 50 kg C .......
G Corrosive solids, 8 UN3095 I 8, 4.2.... None.......... 211........ 243........ 1 kg 25 kg C .......
self-heating,
n.o.s..
.................... ........... .................. II 8, 4.2.... IB6, IP2 None.......... 212........ 242........ 15 kg 50 kg C .......
G Corrosive solids, 8 UN2923 I 8, 6.1.... IB7 None.......... 211........ 242........ 1 kg 25 kg B 40
toxic, n.o.s..
.................... ........... .................. II 8, 6.1.... IB8, IP2, IP4 None.......... 212........ 240........ 15 kg 50 kg B 40
.................... ........... .................. III 8, 6.1.... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg B 40, 95
G Corrosive solids, 8 UN3096 I 8, 4.3.... IB4, IP1 None.......... 211........ 243........ 1 kg 25 kg D .......
water-reactive,
n.o.s..
.................... ........... .................. II 8, 4.3.... IB6, IP2 None.......... 212........ 242........ 15 kg 50 kg D .......
D W Cotton.............. 9 NA1365 ....... 9......... 137, IB8, IP2, None.......... None....... None....... No limit No limit A .......
IP4, W41
A W Cotton waste, oily.. 4.2 UN1364 III 4.2....... IB8, IP6 None.......... 213........ None....... Forbidden Forbidden A 54
A I W Cotton, wet......... 4.2 UN1365 III 4.2....... IB8, IP6 None.......... 204........ 241........ Forbidden Forbidden A .......
Coumarin derivative 3 UN3024 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L B 40
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Coumarin derivative 6.1 UN3026 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
[[Page 151]]
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP27
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Coumarin derivative 6.1 UN3025 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic, flammable
flash point not
less than 23
degrees C.
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1, 3.... B1, IB3, T7, 153........... 203........ 242........ 60 L 220 L A 40
TP1, TP28
Coumarin derivative 6.1 UN3027 I 6.1....... IB7, IP1, T14, None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid, TP2, TP27
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 40
T11, TP2, TP27
.................... ........... .................. III 6.1....... IB8, IP3, T7, 153........... 213........ 240........ 100 kg 200 kg A 40
TP1, TP28
Cresols............. 6.1 UN2076 II 6.1, 8.... IB8, IP2, IP4, None.......... 202........ 243........ 1 L 30 L B .......
T7, TP2
Cresylic acid....... 6.1 UN2022 II 6.1, 8.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 30 L B .......
TP13
Crotonaldehyde, 6.1 UN1143 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden B 40
stabilized. B74, B77, T20,
TP2, TP13, TP38,
TP45
Crotonic acid liquid 8 UN2823 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A 12
Crotonic acid, solid 8 UN2823 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A 12
Crotonylene......... 3 UN1144 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E .......
Cupriethylenediamine 8 UN1761 II 8, 6.1.... IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L A .......
solution.
.................... ........... .................. III 8, 6.1.... IB3, T7, TP1, 154........... 203........ 242........ 5 L 60 L A 95
TP28
Cutters, cable, 1.4S UN0070 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
explosive.
Cyanide or cyanide ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures, dry, see
Cyanides,
inorganic, solid,
n.o.s..
Cyanide solutions, 6.1 UN1935 I 6.1....... B37, T14, TP2, None.......... 201........ 243........ 1 L 30 L B 40, 52
n.o.s.. TP13, TP27
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L A 40, 52
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40, 52
TP13, TP28
Cyanides, inorganic, 6.1 UN1588 I 6.1....... IB7, IP1, N74, None.......... 211........ 242........ 5 kg 50 kg A 52
solid, n.o.s.. N75
.................... ........... .................. II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 52
N74, N75
.................... ........... .................. III 6.1....... IB8, IP3, N74, 153........... 213........ 240........ 100 kg 200 kg A 52
N75
Cyanogen............ 2.3 UN1026 ....... 2.3, 2.1.. 2 None.......... 192........ 245........ Forbidden Forbidden D 40
[[Page 152]]
Cyanogen bromide.... 6.1 UN1889 I 6.1, 8.... A6, A8 None.......... 211........ 242........ 1 kg 15 kg D 40
Cyanogen chloride, 2.3 UN1589 ....... 2.3, 8.... 1 None.......... 192........ 245........ Forbidden Forbidden D 40
stabilized.
Cyanuric chloride... 8 UN2670 II 8......... IB8, IP2, IP4 None.......... 212........ 240........ 15 kg 50 kg A 12, 40
Cyanuric triazide... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Cyclobutane......... 2.1 UN2601 ....... 2.1....... 306........... 304........ 314, 315... Forbidden 150 kg B 40
Cyclobutyl 6.1 UN2744 II 6.1, 8, 3. IB1, T7, TP2, None.......... 202........ 243........ 1 L 30 L A 12, 13,
chloroformate. TP13 21, 25,
40, 100
1,5,9- 6.1 UN2518 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A 40
Cyclododecatriene.
Cycloheptane........ 3 UN2241 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Cycloheptatriene.... 3 UN2603 II 3, 6.1.... IB2, T7, TP1, None.......... 202........ 243........ 1 L 60 L E 40
TP13
Cycloheptene........ 3 UN2242 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Cyclohexane......... 3 UN1145 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
Cyclohexanone....... 3 UN1915 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cyclohexene......... 3 UN2256 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
Cyclohexenyltrichlor 8 UN1762 II 8......... A7, B2, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
osilane. N34, T7, TP2,
TP13
Cyclohexyl acetate.. 3 UN2243 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cyclohexyl 6.1 UN2488 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
isocyanate. B74, B77, T20,
TP2, TP13, TP38,
TP45
Cyclohexyl mercaptan 3 UN3054 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A 40, 95
Cyclohexylamine..... 8 UN2357 II 8, 3...... IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L A 40
Cyclohexyltrichloros 8 UN1763 II 8......... A7, B2, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
ilane. N34, T7, TP2,
TP13
Cyclonite and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
cyclotetramethylene
tetranitramine
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
[[Page 153]]
Cyclonite and HMX ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Cyclonite and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
octogen mixtures,
wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Cyclonite, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Cyclotrimethylenetr
initramine, etc.
Cyclooctadiene ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
phosphines, see 9-
Phosphabicyclononan
es.
Cyclooctadienes..... 3 UN2520 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cyclooctatetraene... 3 UN2358 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Cyclopentane........ 3 UN1146 II 3......... IB2, T7, TP1 150........... 202........ 242........ 5 L 60 L E .......
Cyclopentane, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
methyl, see
Methylcyclopentane.
Cyclopentanol....... 3 UN2244 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cyclopentanone...... 3 UN2245 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Cyclopentene........ 3 UN2246 II 3......... IB2, IP8, T7, 150........... 202........ 242........ 5 L 60 L E .......
TP2
Cyclopropane........ 2.1 UN1027 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg E 40
Cyclotetramethylene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetranitramine (dry
or unphlegmatized)
(HMX).
Cyclotetramethylenet 1.1D UN0484 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
etranitramine,
desensitized or
Octogen,
desensitized or
HMX, desensitized.
Cyclotetramethylenet 1.1D UN0226 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
etranitramine,
wetted or HMX,
wetted or Octogen,
wetted with not
less than 15
percent water, by
mass.
Cyclotrimethylenetri ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
nitramine and
cyclotetramethylene
tetranitramine
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Cyclotrimethylenenit ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
ramine and octogen,
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
[[Page 154]]
Cyclotrimethylenetri ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
nitramine and HMX
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Cyclotrimethylenetri 1.1D UN0483 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
nitramine,
desensitized or
Cyclonite,
desensitized or
Hexogen,
desensitized or
RDX, desensitized.
Cyclotrimethylenetri 1.1D UN0072 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
nitramine, wetted
or Cyclonite,
wetted or Hexogen,
wetted or RDX,
wetted with not
less than 15
percent water by
mass.
Cymenes............. 3 UN2046 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Dangerous Goods in 9 UN3363 ....... .......... 136 None.......... 222........ None....... No limit No limit A .......
Machinery or
Dangerous Goods in
Apparatus.
Decaborane.......... 4.1 UN1868 II 4.1, 6.1.. A19, A20, IB6, None.......... 212........ None....... Forbidden 50 kg A .......
IP2
Decahydronaphthalene 3 UN1147 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
n-Decane............ 3 UN2247 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Deflagrating metal 1.3C UN0132 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 10 5E
salts of aromatic
nitroderivatives,
n.o.s..
Delay electric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
igniter, see
Igniters.
Depth charges, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Charges, depth.
Detonating relays, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Detonators, etc.
Detonator 1.1B UN0360 II 1.1B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
assemblies, non-
electric for
blasting.
Detonator 1.4B UN0361 II 1.4B...... 103 63(f), 63(g).. 62......... None....... Forbidden 75 kg 06 .......
assemblies, non-
electric, for
blasting.
Detonator, 1.4S UN0500 II 1.4S...... 63(f), 63(g).. 62......... None....... 25 kg 100 kg 05 .......
assemblies, non-
electric for
blasting.
Detonators, 1.1B UN0030 II 1.1B...... 63(f), 63(g).. 62......... None....... Forbidden Forbidden 11 .......
electric, for
blasting.
[[Page 155]]
Detonators, 1.4B UN0255 II 1.4B...... 103 63(f), 63(g).. 62......... None....... Forbidden 75 kg 06 .......
electric, for
blasting.
Detonators, electric 1.4S UN0456 II 1.4S...... 63(f), 63(g).. 62......... None....... 25 kg 100 kg 05 .......
for blasting.
Detonators for 1.1B UN0073 II 1.1B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
ammunition.
Detonators for 1.2B UN0364 II 1.2B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
ammunition.
Detonators for 1.4B UN0365 II 1.4B...... 103 None.......... 62......... None....... Forbidden 75 kg 06 .......
ammunition.
Detonators for 1.4S UN0366 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
ammunition.
Detonators, non- 1.1B UN0029 II 1.1B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
electric, for
blasting.
Detonators, non- 1.4B UN0267 II 1.4B...... 103 63(f), 63(g).. 62......... None....... Forbidden 75 kg 06 .......
electric, for
blasting.
Detonators, non- 1.4S UN0455 II 1.4S...... 63(f), 63(g).. 62......... None....... 25 kg 100 kg 5 .......
electric,for
blasting.
Deuterium, 2.1 UN1957 ....... 2.1....... 306........... 302........ None....... Forbidden 150 kg E 40
compressed.
Devices, small, 2.1 UN3150 ....... 2.1....... 306........... 304........ None....... Forbidden 150 kg B 40
hydrocarbon gas
powered or
Hydrocarbon gas
refills for small
devices with
release device.
Di-n-amylamine...... 3 UN2841 III 3, 6.1.... B1, IB3, T4, TP1 150........... 203........ 242........ 60 L 220 L A .......
Di-n-butyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxydicarbonate,
with more than 52
percent in solution.
Di-n-butylamine..... 8 UN2248 II 8, 3...... IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L A .......
2,2-Di-(tert- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
butylperoxy)
butane, with more
than 55 percent in
solution.
Di-(tert- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
butylperoxy)
phthalate, with
more than 55
percent in solution.
2,2-Di-(4,4-di-tert- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
butylperoxycyclohex
yl) propane, with
more than 42
percent with inert
solid.
Di-2,4- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dichlorobenzoyl
peroxide, with more
than 75 percent
with water.
1,2-Di- 3 UN2372 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
(dimethylamino)etha
ne.
Di-2-ethylhexyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
phosphoric acid,
see Diisooctyl acid
phosphate.
Di-(1- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
hydroxytetrazole)
(dry).
Di-(1-naphthoyl) Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide.
a,a'-Di-(nitroxy) Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
methylether.
Di-(beta- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitroxyethyl)
ammonium nitrate.
Diacetone alcohol... 3 UN1148 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 156]]
Diacetone alcohol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxides, with
more than 57
percent in solution
with more than 9
percent hydrogen
peroxide, less than
26 percent
diacetone alcohol
and less than 9
percent water;
total active oxygen
content more than 9
percent by mass.
Diacetyl, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Butanedione.
Diacetyl peroxide, Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
solid, or with more
than 25 percent in
solution.
Diallylamine........ 3 UN2359 II 3, 6.1, 8. IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 21, 40,
100
Diallylether........ 3 UN2360 II 3, 6.1.... IB2, N12, T7, None.......... 202........ 243........ 1 L 60 L E 40
TP1, TP13
4,4'-Diaminodiphenyl 6.1 UN2651 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A .......
methane. TP1
p-Diazidobenzene.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
1,2-Diazidoethane... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
1,1'- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Diazoaminonaphthale
ne.
Diazoaminotetrazole Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Diazodinitrophenol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Diazodinitrophenol, 1.1A UN0074 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
wetted with not
less than 40
percent water or
mixture of alcohol
and water, by mass.
Diazodiphenylmethane Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Diazonium nitrates Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Diazonium Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
perchlorates (dry).
1,3-Diazopropane.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dibenzyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxydicarbonate,
with more than 87
percent with water.
Dibenzyldichlorosila 8 UN2434 II 8......... B2, IB2, T7, 154........... 202........ 242........ 1 L 30 L C 40
ne. TP2, TP13
Diborane, compressed 2.3 UN1911 ....... 2.3, 2.1.. 1 None.......... 302........ None....... Forbidden Forbidden D 40, 57
D Diborane mixtures... 2.1 NA1911 ....... 2.1....... 5 None.......... 302........ 245........ Forbidden Forbidden D 40, 57
[[Page 157]]
Dibromoacetylene.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
1,2-Dibromobutan-3- 6.1 UN2648 II 6.1....... IB2 None.......... 202........ 243........ 5 L 60 L B 40
one.
Dibromochloropropane 6.1 UN2872 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
A Dibromodifluorometha 9 UN1941 III None...... T11, TP2 155........... 203........ 241........ 100 L 220 L A 25
ne, R12B2.
1,2-Dibromoethane, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethylene
dibromide.
Dibromomethane...... 6.1 UN2664 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Dibutyl ethers...... 3 UN1149 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Dibutylaminoethanol. 6.1 UN2873 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
N,N'- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dichlorazodicarbona
midine (salts of)
(dry).
1,1-Dichloro-1- 6.1 UN2650 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 12, 40
nitroethane.
D 3,5-Dichloro-2,4,6- 6.1 NA9264 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A 40
trifluoropyridine. B74, T20, TP4,
TP12, TP13,
TP38, TP45
Dichloroacetic acid. 8 UN1764 II 8......... A3, A6, A7, B2, 154........... 202........ 242........ 1 L 30 L A .......
IB2, N34, T8,
TP2, TP12
1,3-Dichloroacetone. 6.1 UN2649 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg B 12, 40
Dichloroacetyl 8 UN1765 II 8......... A3, A6, A7, B2, 154........... 202........ 242........ 1 L 30 L D 40
chloride. B6, IB2, N34,
T7, TP2
Dichloroacetylene... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
+ Dichloroanilines, 6.1 UN1590 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 40
liquid.
+ Dichloroanilines, 6.1 UN1590 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 40
solid. T7, TP2
+ o-Dichlorobenzene... 6.1 UN1591 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
2,2'-Dichlorodiethyl 6.1 UN1916 II 6.1, 3.... IB2, N33, N34, None.......... 202........ 243........ 5 L 60 L A .......
ether. T7, TP2
Dichlorodifluorometh 2.2 UN2602 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
ane and
difluoroethane
azeotropic mixture
or Refrigerant gas
R 500 with
approximately 74
percent
dichlorodifluoromet
hane.
Dichlorodifluorometh 2.2 UN1028 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
ane or Refrigerant
gas R 12.
Dichlorodimethyl 6.1 UN2249 I 6.1....... None.......... 201........ 243........ Forbidden Forbidden D 40
ether, symmetrical.
1,1-Dichloroethane.. 3 UN2362 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
1,2-Dichloroethane, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethylene
dichloride.
Dichloroethyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
sulfide.
1,2-Dichloroethylene 3 UN1150 II 3......... IB2, T7, TP2 150........... 202........ 242........ 5 L 60 L B .......
Dichlorofluoromethan 2.2 UN1029 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
e or Refrigerant
gas R21.
Dichloroisocyanuric 5.1 UN2465 II 5.1....... 28, IB8, IP4 152........... 212........ 240........ 5 kg 25 kg A 13
acid, dry or
Dichloroisocyanuric
acid salts.
Dichloroisopropyl 6.1 UN2490 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L B .......
ether.
[[Page 158]]
Dichloromethane..... 6.1 UN1593 III 6.1....... IB3, IP8, N36, 153........... 203........ 241........ 60 L 220 L A .......
T7, TP2
Dichloropentanes.... 3 UN1152 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Dichlorophenyl 6.1 UN2250 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg B 25, 40,
isocyanates. T7, TP2 48
Dichlorophenyltrichl 8 UN1766 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
orosilane. N34, T7, TP2,
TP13
1,2-Dichloropropane. 3 UN1279 II 3......... IB2, N36, T4, 150........... 202........ 242........ 5 L 60 L B .......
TP1
1,3-Dichloropropanol- 6.1 UN2750 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 12, 40
2.
Dichloropropene and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
propylene
dichloride mixture,
see 1,2-
Dichloropropane.
Dichloropropenes.... 3 UN2047 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Dichlorosilane...... 2.3 UN2189 ....... 2.3, 2.1, 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 17, 40
8.
1,2-Dichloro-1,1,2,2- 2.2 UN1958 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
tetrafluoroethane
or Refrigerant gas
R 114.
Dichlorovinylchloroa Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
rsine.
Dicycloheptadiene, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Bicyclo [2,2,1]
hepta-2,5-diene,
stabilized.
Dicyclohexylamine... 8 UN2565 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Dicyclohexylammonium 4.1 UN2687 III 4.1....... IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A 48
nitrite.
Dicyclopentadiene... 3 UN2048 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Didymium nitrate.... 5.1 UN1465 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
D Diesel fuel......... 3 NA1993 III None...... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
I Diesel fuel......... 3 UN1202 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Diethanol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrosamine
dinitrate (dry).
Diethoxymethane..... 3 UN2373 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
3,3-Diethoxypropene. 3 UN2374 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Diethyl carbonate... 3 UN2366 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 159]]
Diethyl cellosolve, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethylene glycol
diethyl ether.
Diethyl ether or 3 UN1155 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E 40
Ethyl ether.
Diethyl ketone...... 3 UN1156 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Diethyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxydicarbonate,
with more than 27
percent in solution.
Diethyl sulfate..... 6.1 UN1594 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L C .......
Diethyl sulfide..... 3 UN2375 II 3......... IB2, T7, TP1, None.......... 202........ 243........ 5 L 60 L E .......
TP13
Diethylamine........ 3 UN1154 II 3, 8...... IB2, N34, T7, None.......... 202........ 243........ 1 L 5 L E 40
TP1
2- 8 UN2686 II 8, 3...... B2, IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L A .......
Diethylaminoethanol.
Diethylaminopropylam 3 UN2684 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A .......
ine.
+ N, N-Diethylaniline. 6.1 UN2432 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Diethylbenzene...... 3 UN2049 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Diethyldichlorosilan 8 UN1767 II 8, 3...... A7, B6, IB2, None.......... 202........ 243........ Forbidden 30 L C 40
e. N34, T7, TP2,
TP13
Diethylene glycol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrate.
Diethyleneglycol 1.1D UN0075 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 13 21E
dinitrate,
desensitized with
not less than 25
percent non-
volatile water-
insoluble
phlegmatizer, by
mass.
Diethylenetriamine.. 8 UN2079 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A 40
N,N- 8 UN2685 II 8, 3...... IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L A .......
Diethylethylenediam
ine.
Diethylgold bromide. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Diethylthiophosphory 8 UN2751 II 8......... B2, IB2,T7, TP2 154........... 202........ 242........ 1 L 39 L A 40
l chloride.
Diethylzinc......... 4.2 UN1366 I 4.2, 4.3.. B11, T21, TP2, None.......... 181........ 244........ Forbidden Forbidden D 18
TP7
Difluorochloroethane ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
s, see 1-Chloro-1,1-
difluoroethanes.
1,1-Difluoroethane 2.1 UN1030 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
or Refrigerant gas
R 152a.
1,1-Difluoroethylene 2.1 UN1959 ....... 2.1....... 306........... 304........ None....... Forbidden 150 kg E 40
or Refrigerant gas
R 1132a.
Difluoromethane or 2.1 UN3252 ....... 2.1....... T50 306........... 302........ 314, 315... Forbidden 150 kg D 40
Refrigerant gas R
32.
Difluorophosphoric 8 UN1768 II 8......... A6, A7, B2, IB2, None.......... 202........ 242........ 1 L 30 L A 40
acid, anhydrous. N5, N34, T8,
TP2, TP12
2,3-Dihydropyran.... 3 UN2376 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
1,8-Dihydroxy- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
2,4,5,7-
tetranitroanthraqui
none (chrysamminic
acid).
Diiodoacetylene..... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Diisobutyl ketone... 3 UN1157 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Diisobutylamine..... 3 UN2361 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A .......
[[Page 160]]
Diisobutylene, 3 UN2050 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
isomeric compounds.
Diisooctyl acid 8 UN1902 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
phosphate.
Diisopropyl ether... 3 UN1159 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E 40
Diisopropylamine.... 3 UN1158 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
Diisopropylbenzene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
hydroperoxide, with
more than 72
percent in solution.
Diketene, stabilized 6.1 UN2521 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40, 49
B74, T20, TP2,
TP13, TP38, TP45
1,2-Dimethoxyethane. 3 UN2252 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
1,1-Dimethoxyethane. 3 UN2377 II 3......... IB2, T7, TP1 150........... 202........ 242........ 5 L 60 L B .......
Dimethyl carbonate.. 3 UN1161 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Dimethyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chlorothiophosphate
, see Dimethyl
thiophosphoryl
chloride.
2,5-Dimethyl-2,5- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dihydroperoxy
hexane, with more
than 82 percent
with water.
Dimethyl disulfide.. 3 UN2381 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Dimethyl ether...... 2.1 UN1033 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
Dimethyl-N- 3 UN2266 II 3, 8...... IB2, T7, TP2, None.......... 202........ 243........ 1 L 5 L B 40
propylamine. TP13
Dimethyl sulfate.... 6.1 UN1595 I 6.1, 8.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, B77, T20,
TP2, TP13, TP38,
TP45
Dimethyl sulfide.... 3 UN1164 II 3......... IB1, IP8, T7, None.......... 202........ 242........ 5 L 60 L E 40
TP2
Dimethyl 6.1 UN2267 II 6.1, 8.... IB2, T7, TP2 None.......... 202........ 243........ 1 L 30 L B 25
thiophosphoryl
chloride.
Dimethylamine, 2.1 UN1032 ....... 2.1....... T50 None.......... 304........ 314, 315... Forbidden 150 kg D 40
anhydrous.
Dimethylamine 3 UN1160 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
solution.
2- 3 UN2378 II 3, 6.1.... IB2, T7, TP1 None.......... 202........ 243........ 1 L 60 L A 26, 40
Dimethylaminoaceton
itrile.
2- 8 UN2051 II 8, 3...... B2, IB2, T7, TP2 154........... 202........ 243........ 1 L 30 L A .......
Dimethylaminoethano
l.
2-Dimethylaminoethyl 6.1 UN3302 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L D 25
acrylate.
[[Page 161]]
2-Dimethylaminoethyl 6.1 UN2522 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L B 40
methacrylate.
N,N-Dimethylaniline. 6.1 UN2253 II 6.1....... IB1, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
2,3-Dimethylbutane.. 3 UN2457 II 3......... IB2, T7, TP1 150........... 202........ 242........ 5 L 60 L E .......
1,3- 3 UN2379 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
Dimethylbutylamine.
Dimethylcarbamoyl 8 UN2262 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A 40
chloride.
Dimethylcyclohexanes 3 UN2263 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Dimethylcyclohexylam 8 UN2264 II 8, 3...... B2, IB2, T7, TP2 154........... 202........ 243........ 1 L 30 L A 40
ine.
Dimethyldichlorosila 3 UN1162 II 3, 8...... B77, IB2, T7, None.......... 202........ 243........ Forbidden Forbidden B 40
ne. TP2, TP13
Dimethyldiethoxysila 3 UN2380 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
ne.
Dimethyldioxanes.... 3 UN2707 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
N,N- 3 UN2265 III 3......... B1, IB3, T2, TP2 150........... 203........ 242........ 60 L 220 L A .......
Dimethylformamide.
Dimethylhexane Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dihydroperoxide
(dry).
Dimethylhydrazine, 6.1 UN2382 I 6.1, 3.... 2, A7, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
symmetrical. B32, B74, B77,
T20, TP2, TP13,
TP38, TP45
Dimethylhydrazine, 6.1 UN1163 I 6.1, 3, 8. 2, B7, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 21, 38,
unsymmetrical. B32, B74, T20, 40, 100
TP2, TP13, TP38,
TP45
2,2-Dimethylpropane. 2.1 UN2044 ....... 2.1....... 306........... 304........ 314, 315... Forbidden 150 kg E 40
Dimethylzinc........ 4.2 UN1370 I 4.2, 4.3.. B11, B16, T21, None.......... 181........ 244........ Forbidden Forbidden D 18
TP2, TP7
Dinitro-o-cresol, 6.1 UN1598 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......
solid. T7, TP2
Dinitro-o-cresol, 6.1 UN1598 II 6.1....... IB2, IP2, IP4, None.......... 202........ 243........ 5 L 60 L A .......
solution. T7, TP2
1,3-Dinitro-5,5- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dimethyl hydantoin.
Dinitro-7,8- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dimethylglycoluril
(dry).
1,3-Dinitro-4,5- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrosobenzene.
1,4-Dinitro-1,1,4,4- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetramethylolbutane
tetranitrate (dry).
2,4-Dinitro-1,3,5- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
trimethylbenzene.
Dinitroanilines..... 6.1 UN1596 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 91
T7, TP2
Dinitrobenzenes, 6.1 UN1597 II 6.1....... 11, IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 91
liquid.
Dinitrobenzenes, 6.1 UN1597 II 6.1....... 11, IB8, IP2, None.......... 212........ 242........ 25 kg 100 kg A 91
solid. IP4
Dinitrochlorobenzene ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
, see
Chlorodinitrobenzen
e.
1,2-Dinitroethane... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
1,1-Dinitroethane Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
[[Page 162]]
Dinitrogen tetroxide 2.3 UN1067 ....... 2.3, 5.1, 1, B7, B14, B45, None.......... 336........ 314........ Forbidden Forbidden D 40, 89,
8. B46, B61, B66, 90
B67, B77, T50,
TP21
Dinitroglycoluril or 1.1D UN0489 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
Dingu.
Dinitromethane...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dinitrophenol, dry 1.1D UN0076 II 1.1D, 6.1. None.......... 62......... None....... Forbidden Forbidden 10 5E
or wetted with less
than 15 percent
water, by mass.
Dinitrophenol 6.1 UN1599 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A 36
solutions.
.................... ........... .................. III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A 36
Dinitrophenol, 4.1 UN1320 I 4.1, 6.1.. 23, A8, A19, None.......... 211........ None....... 1 kg 15 kg E 28, 36
wetted with not A20, N41
less than 15
percent water, by
mass.
Dinitrophenolates 1.3C UN0077 II 1.3C, 6.1. None.......... 62......... None....... Forbidden Forbidden 10 5E
alkali metals, dry
or wetted with less
than 15 percent
water, by mass.
Dinitrophenolates, 4.1 UN1321 I 4.1, 6.1.. 23, A8, A19, None.......... 211........ None....... 1 kg 15 kg E 28, 36
wetted with not A20, N41
less than 15
percent water, by
mass.
Dinitropropylene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
glycol.
Dinitroresorcinol, 1.1D UN0078 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 5E
dry or wetted with
less than 15
percent water, by
mass.
2,4- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dinitroresorcinol
(heavy metal salts
of) (dry).
4,6- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dinitroresorcinol
(heavy metal salts
of) (dry).
Dinitroresorcinol, 4.1 UN1322 I 4.1....... 23, A8, A19, None.......... 211........ None....... 1 kg 15 kg E 28, 36
wetted with not A20, N41
less than 15
percent water, by
mass.
3,5-Dinitrosalicylic Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
acid (lead salt)
(dry).
Dinitrosobenzene.... 1.3C UN0406 II 1.3C...... None.......... 62......... None....... Forbidden Forbidden 10 .......
Dinitrosobenzylamidi Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
ne and salts of
(dry).
2,2-Dinitrostilbene. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Dinitrotoluenes, 6.1 UN2038 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
liquid.
Dinitrotoluenes, 6.1 UN1600 II 6.1....... T7, TP3 None.......... 202........ 243........ Forbidden Forbidden C .......
molten.
[[Page 163]]
Dinitrotoluenes, 6.1 UN2038 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......
solid. T7, TP2
1,9-Dinitroxy Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
pentamethylene-2,4,
6,8-tetramine (dry).
Dioxane............. 3 UN1165 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Dioxolane........... 3 UN1166 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Dipentene........... 3 UN2052 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Diphenylamine 6.1 UN1698 I 6.1....... None.......... 201........ None....... Forbidden Forbidden D 40
chloroarsine.
Diphenylchloroarsine 6.1 UN1699 I 6.1....... A8, B14, B32, None.......... 201........ 243........ Forbidden 30 L D 40
, liquid. N33, N34, T14,
TP2, TP13, TP27
Diphenylchloroarsine 6.1 UN1699 I 6.1....... A8, B14, B32, None.......... 211........ 242........ Forbidden 15 kg D 40
, solid. IB7, IP1, N33,
N34
Diphenyldichlorosila 8 UN1769 II 8......... A7, B2, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
ne. N34, T7, TP2,
TP13
Diphenylmethyl 8 UN1770 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg D 40
bromide.
Dipicryl sulfide, 1.1D UN0401 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
dry or wetted with
less than 10
percent water, by
mass.
Dipicryl sulfide, 4.1 UN2852 I 4.1....... A2, N41 None.......... 211........ None....... Forbidden 0.5 kg D 28
wetted with not
less than 10
percent water, by
mass.
Dipicrylamine, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrodiphenylam
ine.
Dipropionyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide, with more
than 28 percent in
solution.
Di-n-propyl ether... 3 UN2384 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Dipropyl ketone..... 3 UN2710 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Dipropylamine....... 3 UN2383 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
G Disinfectant, 8 UN1903 I 8......... A7, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L B .......
liquid, corrosive, TP2, TP27
n.o.s..
G Disinfectants, 8 UN1903 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L B .......
liquid, corrosive
n.o.s..
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
G Disinfectants, 6.1 UN3142 I 6.1....... A4, T14, TP2, None.......... 201........ 243........ 1 L 30 L A 40
liquid, toxic, TP27
n.o.s..
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L A 40
TP27
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A 40
TP28
G Disinfectants, 6.1 UN1601 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
solid, toxic,
n.o.s..
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Disodium 8 UN3253 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
trioxosilicate.
G Dispersant gases, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
n.o.s. see
Refrigerant gases,
n.o.s..
Divinyl ether, 3 UN1167 I 3......... T11, TP2 None.......... 201........ 243........ 1 L 30 L E 40
stabilized.
[[Page 164]]
Dodecyltrichlorosila 8 UN1771 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
ne. N34, T7, TP2,
TP13
Dry ice, see Carbon ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
dioxide, solid.
G Dyes, liquid, 8 UN2801 I 8......... 11, B10, T14, None.......... 201........ 243........ 0.5 L 2.5 L A .......
corrosive, n.o.s. TP2, TP27
or Dye
intermediates,
liquid, corrosive,
n.o.s..
.................... ........... .................. II 8......... 11, B2, IB2, 154........... 202........ 242........ 1 L 30 L A .......
T11, TP2, TP27
.................... ........... .................. III 8......... 11, IB3, T7, 154........... 203........ 241........ 5 L 60 L A .......
TP1, TP28
G Dyes, liquid, toxic, 6.1 UN1602 II 6.1....... IB2 None.......... 202........ 243........ 5 L 60 L A .......
n.o.s. or Dye
intermediates,
liquid, toxic,
n.o.s..
.................... ........... .................. III 6.1....... IB3 153........... 203........ 241........ 60 L 220 L A .......
G Dyes, solid, 8 UN3147 I 8......... IB7, IP1 None.......... 211........ 242........ 1 kg 25 kg A .......
corrosive, n.o.s.
or Dye
intermediates,
solid, corrosive,
n.o.s..
.................... ........... .................. II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
.................... ........... .................. III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
G Dyes, solid, toxic, 6.1 UN3143 I 6.1....... A5, IB7, IP1, None.......... 211........ 242........ 5 kg 50 kg A .......
n.o.s. or Dye T14, TP2, TP27
intermediates,
solid, toxic,
n.o.s..
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Dynamite, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Explosive,
blasting, type A.
Electrolyte (acid or ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
alkali) for
batteries, see
Battery fluid, acid
or Battery fluid,
alkali.
Elevated temperature 3 UN3256 III 3......... IB1, T3, TP3, None.......... None....... 247........ Forbidden Forbidden A .......
liquid, flammable, TP29
n.o.s., with flash
point above 37.8 C,
at or above its
flash point.
[[Page 165]]
Elevated temperature 9 UN3257 III 9......... IB1, T3, TP3, None.......... None....... 247........ Forbidden Forbidden A 85
liquid, n.o.s., at TP29
or above 100 C and
below its flash
point (including
molten metals,
molten salts, etc.).
Elevated temperature 9 UN3258 III 9......... 247(h) (4).... None....... 247........ Forbidden Forbidden A 85
solid, n.o.s., at
or above 240 C, see
Sec. 173.247(h)(4).
Engines, internal 9 UN3166 ....... 9......... 135 220........... 220........ 220........ Forbidden No limit A .......
combustion,
flammable gas
powered.
Engines, internal 9 UN3166 ....... 9......... 135 220........... 220........ 220........ No limit No limit A .......
combustion,
flammable liquid
powered.
G Environmentally 9 UN3082 III 9......... 8, IB3, T4, TP1, 155........... 203........ 241........ No limit No limit A .......
hazardous TP29
substances, liquid,
n.o.s..
G Environmentally 9 UN3077 III 9......... 8, B54, IB8, N20 155........... 213........ 240........ No limit No limit A .......
hazardous
substances, solid,
n.o.s..
Epibromohydrin...... 6.1 UN2558 I 6.1, 3.... T14, TP2, TP13 None.......... 201........ 243........ Forbidden Forbidden D 40
+ Epichlorohydrin..... 6.1 UN2023 II 6.1, 3.... IB2, T7, TP2, None.......... 202........ 243........ 5 L 60 L A 40
TP13
1,2-Epoxy-3- 3 UN2752 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
ethoxypropane.
Esters, n.o.s....... 3 UN3272 II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
Etching acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
liquid, n.o.s., see
Hydrofluoric acid,
solution etc.
Ethane.............. 2.1 UN1035 ....... 2.1....... 306........... 304........ 302........ Forbidden 150 kg E 40
D Ethane-Propane 2.1 NA1961 ....... 2.1....... T75, TP5 None.......... 316........ 314, 315... Forbidden Forbidden D 40
mixture,
refrigerated liquid.
Ethane, refrigerated 2.1 UN1961 ....... 2.1....... T75, TP5 None.......... None....... 315........ Forbidden Forbidden D 40
liquid.
Ethanol amine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrate.
Ethanol or Ethyl 3 UN1170 II 3......... 24, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L A .......
alcohol or Ethanol
solutions or Ethyl
alcohol solutions.
.................... ........... .................. III 3......... 24, B1, IB3, T2, 150........... 203........ 242........ 60 L 220 L A .......
TP1
Ethanolamine or 8 UN2491 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Ethanolamine
solutions.
Ether, see Diethyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
ether.
Ethers, n.o.s....... 3 UN3271 II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
Ethyl acetate....... 3 UN1173 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyl acrylate, 3 UN1917 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B 40
stabilized. TP13
Ethyl alcohol, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Ethanol.
Ethyl aldehyde, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Acetaldehyde.
Ethyl amyl ketone... 3 UN2271 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 166]]
N-Ethyl-N- 6.1 UN2274 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
benzylaniline.
Ethyl borate........ 3 UN1176 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyl bromide....... 6.1 UN1891 II 6.1....... IB2, IP8, T7, None.......... 202........ 243........ 5 L 60 L B 40, 85
TP2, TP13
Ethyl bromoacetate.. 6.1 UN1603 II 6.1, 3.... IB2, T7, TP2 None.......... 202........ 243........ Forbidden Forbidden D 40
Ethyl butyl ether... 3 UN1179 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyl butyrate...... 3 UN1180 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Ethyl chloride...... 2.1 UN1037 ....... 2.1....... B77, T50 None.......... 322........ 314, 315... Forbidden 150 kg B 40
Ethyl chloroacetate. 6.1 UN1181 II 6.1, 3.... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
Ethyl chloroformate. 6.1 UN1182 I 6.1, 3, 8. 2, A3, A6, A7, None.......... 227........ 244........ Forbidden Forbidden D 21, 40,
B9, B14, B32, 100
B74, N34, T20,
TP2, TP13, TP38,
TP45
Ethyl 2- 3 UN2935 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
chloropropionate.
+ Ethyl 8 UN2826 II 8, 6.1, 3. 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A 40
chlorothioformate. B74, T20, TP2,
TP38, TP45
Ethyl crotonate..... 3 UN1862 II 3......... IB2, T4, TP2 150........... 202........ 242........ 5 L 60 L B .......
Ethyl ether, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Diethyl ether.
Ethyl fluoride or 2.1 UN2453 ....... 2.1....... 306........... 304........ 314, 315... Forbidden 150 kg E 40
Refrigerant gas
R161.
Ethyl formate....... 3 UN1190 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
Ethyl hydroperoxide. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Ethyl isobutyrate... 3 UN2385 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
+ Ethyl isocyanate.... 3 UN2481 I 3, 6.1.... 1, A7, B9, B14, None.......... 226........ 244........ Forbidden Forbidden D 40
B30, B72, T22,
TP2, TP13, TP38,
TP44
Ethyl lactate....... 3 UN1192 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Ethyl mercaptan..... 3 UN2363 I 3......... T11, TP2, TP13 None.......... 201........ 243........ Forbidden 30 L E 95, 102
Ethyl methacrylate.. 3 UN2277 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyl methyl ether.. 2.1 UN1039 ....... 2.1....... None.......... 201........ 314, 315... Forbidden 150 kg B 40
Ethyl methyl ketone 3 UN1193 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
or Methyl ethyl
ketone.
Ethyl nitrite 3 UN1194 I 3, 6.1.... None.......... 201........ None....... Forbidden Forbidden E 40, 105
solutions.
Ethyl orthoformate.. 3 UN2524 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 167]]
Ethyl oxalate....... 6.1 UN2525 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Ethyl perchlorate... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
D Ethyl 6.1 NA2927 I 6.1, 8.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
phosphonothioic B74, T20, TP4,
dichloride, TP12, TP13,
anhydrous. TP38, TP45
D Ethyl phosphonous 6.1 NA2845 I 6.1, 4.2.. 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 18
dichloride, B74, T20, TP4,
anhydrous TP12, TP13,
pyrophoric liquid. TP38, TP45
D Ethyl 6.1 NA2927 I 6.1, 8.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
phosphorodichlorida B74, T20, TP4,
te. TP12, TP13,
TP38, TP45
Ethyl propionate.... 3 UN1195 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyl propyl ether.. 3 UN2615 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
Ethyl silicate, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Tetraethyl silicate.
Ethylacetylene, 2.1 UN2452 ....... 2.1....... None.......... 304........ 314, 315... Forbidden 150 kg B 40
stabilized.
Ethylamine.......... 2.1 UN1036 ....... 2.1....... B77, T50 None.......... 321........ 314, 315... Forbidden 150 kg D 40
Ethylamine, aqueous 3 UN2270 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 40
solution with not
less than 50
percent but not
more than 70
percent ethylamine.
N-Ethylaniline...... 6.1 UN2272 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
2-Ethylaniline...... 6.1 UN2273 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Ethylbenzene........ 3 UN1175 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
N- 6.1 UN2753 III 6.1....... IB3, T7, TP1 153........... 203........ 241........ 60 L 220 L A .......
Ethylbenzyltoluidin
es liquid.
N- 6.1 UN2753 III 6.1....... IB8, IP3, T7, 153........... 213........ 240........ 100 kg 200 kg A .......
Ethylbenzyltoluidin TP1
es solid.
2-Ethylbutanol...... 3 UN2275 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Ethylbutyl acetate.. 3 UN1177 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
2-Ethylbutyraldehyde 3 UN1178 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Ethyldichloroarsine. 6.1 UN1892 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, T20, TP2,
TP13, TP38, TP45
Ethyldichlorosilane. 4.3 UN1183 I 4.3, 8, 3. A2, A3, A7, N34, None.......... 201........ 244........ Forbidden 1 L D 21, 28,
T10, TP2, TP7, 40, 49,
TP13 100
Ethylene, acetylene 2.1 UN3138 ....... 2.1....... T75, TP5 None.......... 304........ 314, 315... Forbidden Forbidden D 40
and propylene in
mixture,
refrigerated liquid
with at least 71.5
percent ethylene
with not more than
22.5 percent
acetylene and not
more than 6 percent
propylene.
[[Page 168]]
Ethylene 6.1 UN1135 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
chlorohydrin. B74, T20, TP2,
TP13, TP38, TP45
Ethylene, compressed 2.1 UN1962 ....... 2.1....... 306........... 304........ 302........ Forbidden 150 kg E 40
Ethylene diamine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
diperchlorate.
Ethylene dibromide.. 6.1 UN1605 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
B74, B77, T20,
TP2, TP13, TP38,
TP45
Ethylene dibromide ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
and methyl bromide
liquid mixtures,
see Methyl bromide
and ethylene
dibromide, liquid
mixtures.
Ethylene dichloride. 3 UN1184 II 3, 6.1.... IB2, T7, TP1 None.......... 202........ 243........ 1 L 60 L B 40
Ethylene glycol 3 UN1153 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
diethyl ether.
Ethylene glycol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrate.
Ethylene glycol 3 UN1171 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
monoethyl ether.
Ethylene glycol 3 UN1172 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
monoethyl ether
acetate.
Ethylene glycol 3 UN1188 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
monomethyl ether.
Ethylene glycol 3 UN1189 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
monomethyl ether
acetate.
Ethylene oxide and 2.3 UN3300 ....... 2.3, 2.1.. 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40
carbon dioxide
mixture with more
than 87 percent
ethylene oxide.
Ethylene oxide and 2.1 UN1041 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 25 kg B 40
carbon dioxide
mixtures with more
than 9 percent but
not more than 87
percent ethylene
oxide.
Ethylene oxide and 2.2 UN1952 ....... 2.2....... 306........... 304........ 314, 315... 75 kg 150 kg A .......
carbon dioxide
mixtures with not
more than 9 percent
ethylene oxide.
Ethylene oxide and 2.2 UN3297 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
chlorotetrafluoroet
hane mixture with
not more than 8.8
percent ethylene
oxide.
[[Page 169]]
Ethylene oxide and 2.2 UN3070 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
dichlorodifluoromet
hane mixture, with
not more than 12.5
percent ethylene
oxide.
Ethylene oxide and 2.2 UN3298 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
pentafluoroethane
mixture with not
more than 7.9
percent ethylene
oxide.
Ethylene oxide and 3 UN2983 I 3, 6.1.... 5, A11, N4, N34, None.......... 201........ 243........ Forbidden 30 L E 40
propylene oxide T14, TP2, TP7,
mixtures, with not TP13
more than 30
percent ethylene
oxide.
Ethylene oxide and 2.2 UN3299 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
tetrafluoroethane
mixture with not
more than 5.6
percent ethylene
oxide.
Ethylene oxide or 2.3 UN1040 ....... 2.3, 2.1.. 4, T50, TP20 None.......... 323........ 323........ Forbidden 25 kg D 40
Ethylene oxide with
nitrogen up to a
total pressure of
1MPa (10 bar) at 50
degrees C.
Ethylene, 2.1 UN1038 ....... 2.1....... T75, TP5 None.......... 316........ 318, 319... Forbidden Forbidden D 40
refrigerated liquid
(cryogenic liquid).
Ethylenediamine..... 8 UN1604 II 8, 3...... IB2, T7, TP2 154........... 202........ 243........ 1 L 30 L A 40
Ethyleneimine, 6.1 UN1185 I 6.1, 3.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
stabilized. B72, B77, N25,
N32, T22, TP2,
TP13, TP38, TP44
Ethylhexaldehyde, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Octyl aldehydes
etc.
2-Ethylhexyl 6.1 UN2748 II 6.1, 8.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 30 L A 12, 13,
chloroformate. TP13 21, 25,
40, 100
2-Ethylhexylamine... 3 UN2276 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A 40
Ethylphenyldichloros 8 UN2435 II 8......... A7, B2, IB2, None.......... 202........ 242........ Forbidden 30 L C .......
ilane. N34, T7, TP2,
TP13
1-Ethylpiperidine... 3 UN2386 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
N-Ethyltoluidines... 6.1 UN2754 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
Ethyltrichlorosilane 3 UN1196 II 3, 8...... A7, IB1, N34, None.......... 202........ 243........ 1 L 5 L B 40
T7, TP2, TP13
Etiologic agent, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Infectious
substances, etc.
Explosive articles, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Articles,
explosive , n.o.s.
etc.
Explosive, blasting, 1.1D UN0081 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 21E
type A.
Explosive, blasting, 1.1D UN0082 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
type B.
Explosive, blasting, 1.5D UN0331 II 1.5D...... 105, 106 None.......... 62......... None....... Forbidden Forbidden 10 .......
type B or Agent
blasting, Type B.
Explosive, blasting, 1.1D UN0083 II 1.1D...... 123 None.......... 62......... None....... Forbidden Forbidden 10 22E
type C.
[[Page 170]]
Explosive, blasting, 1.1D UN0084 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
type D.
Explosive, blasting, 1.1D UN0241 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 19E
type E.
Explosive, blasting, 1.5D UN0332 II 1.5D...... 105, 106 None.......... 62......... None....... Forbidden Forbidden 10 .......
type E or Agent
blasting, Type E.
Explosive, Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
forbidden. See Sec.
173.54.
Explosive ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
substances, see
Substances,
explosive, n.o.s.
etc.
Explosives, slurry, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Explosive,
blasting, type E.
Explosives, water ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gels, see
Explosive,
blasting, type E.
Extracts, aromatic, 3 UN1169 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
liquid. TP8
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Extracts, flavoring, 3 UN1197 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
liquid. TP8
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Fabric with animal ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
or vegetable oil,
see Fibers or
fabrics, etc.
Ferric arsenate..... 6.1 UN1606 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Ferric arsenite..... 6.1 UN1607 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Ferric chloride, 8 UN1773 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
anhydrous.
Ferric chloride, 8 UN2582 III 8......... B15, IB3, T4, 154........... 203........ 241........ 5 L 60 L A .......
solution. TP1
Ferric nitrate...... 5.1 UN1466 III 5.1....... A1, A29, IB8, 152........... 213........ 240........ 25 kg 100 kg A .......
IP3
Ferrocerium......... 4.1 UN1323 II 4.1....... 59, A19, IB8, 151........... 212........ 240........ 15 kg 50 kg A .......
IP2, IP4
Ferrosilicon, with 4.3 UN1408 III 4.3, 6.1.. A1, A19, IB8, 151........... 213........ 240........ 25 kg 100 kg A 13, 40,
30 percent or more IP4 85, 103
but less than 90
percent silicon.
Ferrous arsenate.... 6.1 UN1608 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
D Ferrous chloride, 8 NA1759 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
solid.
D Ferrous chloride, 8 NA1760 II 8......... B3, IB2, T11, 154........... 202........ 242........ 1 L 30 L B 40
solution. TP2, TP27
[[Page 171]]
Ferrous metal 4.2 UN2793 III 4.2....... A1, A19, IB8, None.......... 213........ 241........ 25 kg 100 kg A .......
borings or Ferrous IP3, IP6
metal shavings or
Ferrous metal
turnings or Ferrous
metal cuttings in a
form liable to self-
heating.
Fertilizer 2.2 UN1043 ....... 2.2....... 306........... 304........ 314, 315... Forbidden 150 kg E 40
ammoniating
solution with free
ammonia.
A W Fibers or Fabrics, 4.2 UN1373 III 4.2....... 137, IB8, IP3 None.......... 213........ 241........ Forbidden Forbidden A .......
animal or vegetable
or Synthetic,
n.o.s. with animal
or vegetable oil.
Fibers or Fabrics 4.1 UN1353 III 4.1....... A1, IB8, IP3 None.......... 213........ 240........ 25 kg 100 kg D .......
impregnated with
weakly nitrated
nitrocellulose,
n.o.s..
Films, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrocellulose
base, from which
gelatine has been
removed; film
scrap, see
Celluloid scrap.
Films, 4.1 UN1324 III 4.1....... None.......... 183........ None....... 25 kg 100 kg D 91
nitrocellulose
base, gelatine
coated (except
scrap).
Fire extinguisher 8 UN1774 II 8......... N41 154........... 202........ None....... 1 L 30 L A .......
charges, corrosive
liquid.
Fire extinguisher ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
charges, expelling,
explosive, see
Cartridges, power
device.
Fire extinguishers 2.2 UN1044 ....... 2.2....... 18, 110 309........... 309........ None....... 75 kg 150 kg A .......
containing
compressed or
liquefied gas.
Firelighters, solid 4.1 UN2623 III 4.1....... A1, A19 None.......... 213........ None....... 25 kg 100 kg A .......
with flammable
liquid.
Fireworks........... 1.1G UN0333 II 1.1G...... 108 None.......... 62......... None....... Forbidden Forbidden 07 .......
Fireworks........... 1.2G UN0334 II 1.2G...... 108 None.......... 62......... None....... Forbidden Forbidden 07 .......
Fireworks........... 1.3G UN0335 II 1.3G...... 108 None.......... 62......... None....... Forbidden Forbidden 07 .......
Fireworks........... 1.4G UN0336 II 1.4G...... 108 None.......... 62......... None....... Forbidden 75 kg 06 .......
Fireworks........... 1.4S UN0337 II 1.4S...... 108 None.......... 62......... None....... 25 kg 100 kg 05 .......
First aid kits...... 9 UN3316 ....... 9......... 15 None.......... None....... None....... 10 kg 10 kg A .......
W Fish meal, 9 UN2216 III None...... IB8 155........... 218........ 218........ No limit No limit A 88
stabilized or Fish
scrap, stabilized.
Fish meal, 4.2 UN1374 II 4.2....... A1, A19, IB8, None.......... 212........ 241........ 15 kg 50 kg A 119,
unstablized or Fish IP2 120
scrap, unstabilized.
Fissile radioactive ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
materials, see
Radioactive
material, fissile,
n.o.s..
Flammable compressed ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gas, see Compressed
or Liquefied gas,
flammable, etc.
Flammable compressed ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gas (small
receptacles not
fitted with a
dispersion device,
not refillable),
see Receptacles,
etc.
[[Page 172]]
Flammable gas in ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
lighters, see
Lighters or lighter
refills,
cigarettes,
containing
flammable gas.
G Flammable liquid, 3 UN3286 I 3, 6.1, 8. T14, TP2, TP13, None.......... 201........ 243........ Forbidden 2.5 L E 21, 40,
toxic, corrosive, TP27 100
n.o.s..
.................... ........... .................. II 3, 6.1, 8. IB2, T11, TP2, None.......... 202........ 243........ 1 L 5 L B 21, 40,
TP13, TP27 100
G Flammable liquids, 3 UN2924 I 3, 8...... T14, TP2 None.......... 201........ 243........ 0.5 L 2.5 L E 40
corrosive, n.o.s..
.................... ........... .................. II 3, 8...... IB2, T11, TP2, None.......... 202........ 243........ 1 L 5 L B 40
TP27
.................... ........... .................. III 3, 8...... B1, IB3, T7, 150........... 203........ 242........ 5 L 60 L A 40
TP1, TP28
G Flammable liquids, 3 UN1993 I 3......... T11, TP1 150........... 201........ 243........ 1 L 30 L E .......
n.o.s..
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, B52, IB3, 150........... 203........ 242........ 60 L 220 L A .......
T4, TP1, TP29
G Flammable liquids, 3 UN1992 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L E 40
toxic, n.o.s.. TP27
.................... ........... .................. II 3, 6.1.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13
.................... ........... .................. III 3, 6.1.... B1, IB3, T7, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP28
G Flammable solid, 4.1 UN3180 II 4.1, 8.... A1, IB6, IP2 151........... 212........ 242........ 15 kg 50 kg D 40
corrosive,
inorganic, n.o.s..
.................... ........... .................. III 4.1, 8.... A1, IB6 151........... 213........ 242........ 25 kg 100 kg D 40
G Flammable solid, 4.1 UN3178 II 4.1....... A1, IB8, IP2, 151........... 212........ 240........ 15 kg 50 kg B .......
inorganic, n.o.s.. IP4
.................... ........... .................. III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg B .......
G Flammable solid, 4.1 UN3176 II 4.1....... IB1, T3, TP3, 151........... 212........ 240........ Forbidden Forbidden C .......
organic, molten, TP26
n.o.s..
.................... ........... .................. III 4.1....... IB1, T1, TP3, 151........... 213........ 240........ Forbidden Forbidden C .......
TP26
G Flammable solid, 4.1 UN3097 II 4.1, 5.1.. 131 None.......... 214........ 214........ Forbidden Forbidden E 40
oxidizing, n.o.s..
.................... ........... .................. III 4.1, 5.1.. 131 None.......... 214........ 214........ Forbidden Forbidden D 40
[[Page 173]]
G Flammable solid, 4.1 UN3179 II 4.1, 6.1.. A1, IB6, IP2 151........... 212........ 242........ 15 kg 50 kg B 40
toxic, inorganic,
n.o.s..
.................... ........... .................. III 4.1, 6.1.. A1, IB6 151........... 213........ 242........ 25 kg 100 kg B 40
G Flammable solids, 4.1 UN2925 II 4.1, 8.... A1, IB6, IP2 None.......... 212........ 242........ 15 kg 50 kg D 40
corrosive, organic,
n.o.s..
.................... ........... .................. III 4.1, 8.... A1, IB6 151........... 213........ 242........ 25 kg 100 kg D 40
G Flammable solids, 4.1 UN1325 II 4.1....... A1, IB8, IP2, 151........... 212........ 240........ 15 kg 50 kg B .......
organic, n.o.s.. IP4, T3, TP1
.................... ........... .................. III 4.1....... A1, IB8, IP3, 151........... 213........ 240........ 25 kg 100 kg B .......
T1, TP1
G Flammable solids, 4.1 UN2926 II 4.1, 6.1.. A1, IB6, IP2 None.......... 212........ 242........ 15 kg 50 kg B 40
toxic, organic,
n.o.s..
.................... ........... .................. III 4.1, 6.1.. A1, IB6 151........... 213........ 242........ 25 kg 100 kg B 40
Flares, aerial...... 1.3G UN0093 II 1.3G...... None.......... 62......... None....... Forbidden 75 kg 07 .......
Flares, aerial...... 1.4G UN0403 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Flares, aerial...... 1.4S UN0404 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
Flares, aerial...... 1.1G UN0420 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Flares, aerial...... 1.2G UN0421 II 1.2G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Flares, airplane, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Flares, aerial.
Flares, signal, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Cartridges, signal.
Flares, surface..... 1.3G UN0092 II 1.3G...... None.......... 62......... None....... Forbidden 75 kg 07 .......
Flares, surface..... 1.1G UN0418 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Flares, surface..... 1.2G UN0419 II 1.2G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Flares, water- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
activated, see
Contrivances, water-
activated, etc.
Flash powder........ 1.1G UN0094 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 15 .......
Flash powder........ 1.3G UN0305 II 1.3G...... None.......... 62......... None....... Forbidden Forbidden 15 .......
Flue dusts, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
poisonous, see
Arsenical dust.
Fluoric acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hydrofluoric acid,
etc.
Fluorine, compressed 2.3 UN1045 ....... 2.3, 5.1, 1 None.......... 302........ None....... Forbidden Forbidden D 40, 89,
8. 90
Fluoroacetic acid... 6.1 UN2642 I 6.1....... IB7, IP1 None.......... 211........ 242........ 1 kg 15 kg E .......
Fluoroanilines...... 6.1 UN2941 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Fluorobenzene....... 3 UN2387 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Fluoroboric acid.... 8 UN1775 II 8......... A6, A7, B2, B15, 154........... 202........ 242........ 1 L 30 L A .......
IB2, N3, N34,
T7, TP2
Fluorophosphoric 8 UN1776 II 8......... A6, A7, B2, IB2, None.......... 202........ 242........ 1 L 30 L A .......
acid anhydrous. N3, N34, T8,
TP2, TP12
Fluorosilicates, 6.1 UN2856 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 26
n.o.s..
[[Page 174]]
Fluorosilicic acid.. 8 UN1778 II 8......... A6, A7, B2, B15, None.......... 202........ 242........ 1 L 30 L A .......
IB2, N3, N34,
T8, TP2, TP12
Fluorosulfonic acid. 8 UN1777 I 8......... A3, A6, A7, A10, None.......... 201........ 243........ 0.5 L 2.5 L D 40
B6, B10, N3,
T10, TP2, TP12
Fluorotoluenes...... 3 UN2388 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
Forbidden materials. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
See Sec. 173.21.
Formaldehyde, 3 UN1198 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A 40
solutions,
flammable.
Formaldehyde, 8 UN2209 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
solutions, with not
less than 25
percent
formaldehyde.
Formalin, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Formaldehyde,
solutions.
Formic acid......... 8 UN1779 II 8......... B2, B28, IB2, 154........... 202........ 242........ 1 L 30 L A 40
T7, TP2
Fracturing devices, 1.1D UN0099 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
explosive, without
detonators for oil
wells.
Fuel, aviation, 3 UN1863 I 3......... T11, TP1, TP8 150........... 201........ 243........ 1 L 30 L E .......
turbine engine.
.................... ........... .................. II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
D Fuel oil (No. 1, 2, 3 NA1993 III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
4, 5, or 6). TP1, TP29
Fuel system ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
components
(including fuel
control units
(FCU), carburetors,
fuel lines, fuel
pumps) see
Dangerous Goods in
Apparatus or
Dangerous Goods in
Machinery.
Fulminate of mercury Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Fulminate of ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mercury, wet, see
Mercury fulminate,
etc.
Fulminating gold.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Fulminating mercury. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Fulminating platinum Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Fulminating silver.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
[[Page 175]]
Fulminic acid....... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Fumaryl chloride.... 8 UN1780 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L C 8, 40
Fumigated lading, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Secs.
172.302(g), 173.9
and 176.76(h).
Fumigated transport ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
vehicle or freight
container see 173.9.
Furaldehydes........ 6.1 UN1199 II 6.1, 3.... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L A .......
Furan............... 3 UN2389 I 3......... T12, TP2, TP13 None.......... 201........ 243........ 1 L 30 L E 40
Furfuryl alcohol.... 6.1 UN2874 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A 26, 74
Furfurylamine....... 3 UN2526 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A 40
Fuse, detonating, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
metal clad, see
Cord, detonating,
metal clad.
Fuse, detonating, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mild effect, metal
clad, see Cord,
detonating, mild
effect, metal clad.
Fuse, igniter 1.4G UN0103 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
tubular metal clad.
Fuse, non-detonating 1.3G UN0101 II 1.3G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
instantaneous or
quickmatch.
Fuse, safety........ 1.4S UN0105 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
D Fusee (railway or 4.1 NA1325 II 4.1....... None.......... 184........ None....... 15 kg 50 kg B .......
highway).
Fusel oil........... 3 UN1201 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
.................... ........... .................. III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Fuses, tracer, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Tracers for
ammunition.
Fuzes, combination, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
percussion and
time, see Fuzes,
detonating (UN0257,
UN0367); Fuzes,
igniting (UN0317,
UN0368).
Fuzes, detonating... 1.1B UN0106 II 1.1B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
Fuzes, detonating... 1.2B UN0107 II 1.2B...... None.......... 62......... None....... Forbidden Forbidden 11 .......
Fuzes, detonating... 1.4B UN0257 II 1.4B...... 116 None.......... 62......... None....... Forbidden 75 kg 06 .......
Fuzes, detonating... 1.4S UN0367 II 1.4S...... 116 None.......... 62......... None....... 25 kg 100 kg 05 .......
Fuzes, detonating, 1.1D UN0408 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
with protective
features.
Fuzes, detonating, 1.2D UN0409 II 1.2D...... None.......... 62......... None....... Forbidden Forbidden 07 .......
with protective
features.
Fuzes, detonating, 1.4D UN0410 II 1.4D...... 116 None.......... 62......... None....... Forbidden 75 kg 06 .......
with protective
features.
Fuzes, igniting..... 1.3G UN0316 II 1.3G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Fuzes, igniting..... 1.4G UN0317 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Fuzes, igniting..... 1.4S UN0368 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
Galactsan trinitrate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Gallium............. 8 UN2803 III 8......... None.......... 162........ 240........ 20 kg 20 kg B 48
Gas cartridges, 2.1 UN2037 ....... 2.1....... 306........... 304........ None....... 1 kg 15 kg B 40
(flammable) without
a release device,
non-refillable.
[[Page 176]]
Gas generator 2.2 .................. ....... 2.2....... None.......... 335........ None....... 75 kg 150 kg A .......
assemblies
(aircraft),
containing a non-
flammable non-toxic
gas and a
propellant
cartridge.
D Gas identification 2.3 NA9035 ....... 2.3....... 6 None.......... 194........ None....... Forbidden Forbidden D .......
set.
Gas oil............. 3 UN1202 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
G Gas, refrigerated 2.1 UN3312 ....... 2.1....... T75, TP5 None.......... 316........ 318........ Forbidden Forbidden D 40
liquid, flammable,
n.o.s. (cryogenic
liquid).
G Gas, refrigerated 2.2 UN3158 ....... 2.2....... T75, TP5 320........... 316........ 318........ 50 kg 500 kg D .......
liquid, n.o.s.
(cryogenic liquid).
G Gas, refrigerated 2.2 UN3311 ....... 2.2, 5.1.. T75, TP5 320........... 316........ 318........ Forbidden Forbidden D .......
liquid, oxidizing,
n.o.s. (cryogenic
liquid).
Gas sample, non- 2.1 UN3167 ....... 2.1....... 306........... 302, 304... None....... 1 L 5 L D .......
pressurized,
flammable, n.o.s.,
not refrigerated
liquid.
Gas sample, non- 2.3 UN3168 ....... 2.3, 2.1.. 306........... 302........ None....... Forbidden 1 L D .......
pressurized, toxic,
flammable, n.o.s.,
not refrigerated
liquid.
Gas sample, non- 2.3 UN3169 ....... 2.3....... 306........... 302, 304... None....... Forbidden 1 L D .......
pressurized, toxic,
n.o.s., not
refrigerated liquid.
D Gasohol gasoline 3 NA1203 II 3......... 150........... 202........ 242........ 5 L 60 L E .......
mixed with ethyl
alcohol, with not
more than 20
percent alcohol.
Gasoline............ 3 UN1203 II 3......... B33, IB2, T4, 150........... 202........ 242........ 5 L 60 L E .......
TP1
Gasoline, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
casinghead, see
Gasoline.
Gelatine, blasting, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Explosive,
blasting, type A.
Gelatine dynamites, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Explosive,
blasting, type A.
Germane............. 2.3 UN2192 ....... 2.3, 2.1.. 2 None.......... 192........ 245........ Forbidden Forbidden D 40
Glycerol-1,3- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrate.
Glycerol gluconate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
trinitrate.
Glycerol lactate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
trinitrate.
Glycerol alpha- 6.1 UN2689 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
monochlorohydrin.
[[Page 177]]
Glyceryl trinitrate, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Nitroglycerin,
etc.
Glycidaldehyde...... 3 UN2622 II 3, 6.1.... IB2, IP8, T7, 150........... 202........ 243........ 1 L 60 L A 40
TP1
Grenades, hand or 1.1D UN0284 II 1.1D...... ............. 62......... None....... Forbidden Forbidden 07 .......
rifle, with
bursting charge.
Grenades, hand or 1.2D UN0285 II 1.2D...... ............. 62......... None....... Forbidden Forbidden 07 .......
rifle, with
bursting charge.
Grenades, hand or 1.1F UN0292 II 1.1F...... ............. 62......... None....... Forbidden Forbidden 08 .......
rifle, with
bursting charge.
Grenades, hand or 1.2F UN0293 II 1.2F...... ............. 62......... None....... Forbidden Forbidden 08 .......
rifle, with
bursting charge.
Grenades, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
illuminating, see
Ammunition,
illuminating, etc.
Grenades, practice, 1.4S UN0110 II 1.4S...... ............. 62......... None....... 25 kg 100 kg 05 .......
hand or rifle.
Grenades, practice, 1.3G UN0318 II 1.3G...... ............. 62......... None....... Forbidden Forbidden 07 .......
hand or rifle.
Grenades, practice, 1.2G UN0372 II 1.2G...... ............. 62......... None....... Forbidden Forbidden 07 .......
hand or rifle.
Grenades practice 1.4G UN0452 II 1.4G...... ............. 62......... None....... Forbidden 75 kg 06 .......
Hand or rifle.
Grenades, smoke, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Ammunition, smoke,
etc.
Guanidine nitrate... 5.1 UN1467 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A 73
Guanyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrosaminoguanylid
ene hydrazine (dry).
Guanyl 1.1A UN0113 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
nitrosaminoguanylid
ene hydrazine,
wetted with not
less than 30
percent water, by
mass.
Guanyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitrosaminoguanylte
trazene (dry).
Guanyl 1.1A UN0114 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
nitrosaminoguanylte
trazene, wetted or
Tetrazene, wetted
with not less than
30 percent water or
mixture of alcohol
and water, by mass.
Gunpowder, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
compressed or
Gunpowder in
pellets, see Black
powder (UN 0028).
Gunpowder, granular ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
or as a meal, see
Black powder (UN
0027).
Hafnium powder, dry. 4.2 UN2545 I 4.2....... None.......... 211........ 242........ Forbidden Forbidden D .......
.................... ........... .................. II 4.2....... A19, A20, IB6, None.......... 212........ 241........ 15 kg 50 kg D .......
IP2, N34
.................... ........... .................. III 4.2....... IB8, IP3 None.......... 213........ 241........ 25 kg 100 kg D .......
[[Page 178]]
Hafnium powder, 4.1 UN1326 II 4.1....... A6, A19, A20, None.......... 212........ 241........ 15 kg 50 kg E .......
wetted with not IB6, IP2, N34
less than 25
percent water (a
visible excess of
water must be
present) (a)
mechanically
produced, particle
size less than 53
microns; (b)
chemically
produced, particle
size less than 840
microns.
Hand signal device, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Signal devices,
hand.
Hazardous ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
substances, liquid
or solid, n.o.s.,
see Environmentally
hazardous
substances, etc.
D G Hazardous waste, 9 NA3082 III 9......... IB3, T2, TP1 155........... 203........ 241........ No limit No limit A .......
liquid, n.o.s..
D G Hazardous waste, 9 NA3077 III 9......... B54, IB8, IP2 155........... 213........ 240........ No limit No limit A .......
solid, n.o.s..
Heating oil, light.. 3 UN1202 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Helium, compressed.. 2.2 UN1046 ....... 2.2....... 306........... 302........ 302, 314... 75 kg 150 kg A 85
Helium-oxygen ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixture, see Rare
gases and oxygen
mixtures.
Helium, refrigerated 2.2 UN1963 ....... 2.2....... T75, TP5 320........... 316........ 318........ 50 kg 500 kg B .......
liquid (cryogenic
liquid).
Heptafluoropropane 2.2 UN3296 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
or Refrigerant gas
R 227.
n-Heptaldehyde...... 3 UN3056 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Heptanes............ 3 UN1206 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
n-Heptene........... 3 UN2278 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Hexachloroacetone... 6.1 UN2661 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L B 12, 40
Hexachlorobenzene... 6.1 UN2729 III 6.1....... IB3 153........... 203........ 241........ 60 L 220 L A .......
Hexachlorobutadiene. 6.1 UN2279 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
Hexachlorocyclopenta 6.1 UN2646 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40
diene. B74, B77, T20,
TP2, TP13, TP38,
TP45
Hexachlorophene..... 6.1 UN2875 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Hexadecyltrichlorosi 8 UN1781 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
lane. N34, T7, TP2
[[Page 179]]
Hexadienes.......... 3 UN2458 II 3......... IB2, T4, TP1 None.......... 202........ 242........ 5 L 60 L B .......
Hexaethyl 2.3 UN1612 ....... 2.3....... 3 None.......... 334........ None....... Forbidden Forbidden D 40
tetraphosphate and
compressed gas
mixtures.
Hexaethyl 6.1 UN1611 II 6.1....... IB2, IP2, IP4, None.......... 202........ 243........ 5 L 60 L E 40
tetraphosphate, N76
liquid.
Hexaethyl 6.1 UN1611 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg E 40
tetraphosphate, N76
solid.
Hexafluoroacetone... 2.3 UN2420 ....... 2.3, 8.... 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
Hexafluoroacetone 6.1 UN2552 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L B 40
hydrate.
Hexafluoroethane, 2.2 UN2193 ....... 2.2....... 306........... 304........ 314, 315... 75 kg 150 kg A .......
compressed or
Refrigerant gas R
116.
Hexafluorophosphoric 8 UN1782 II 8......... A6, A7, B2, IB2, None.......... 202........ 242........ 1 L 30 L A .......
acid. N3, N34, T8,
TP2, TP12
Hexafluoropropylene 2.2 UN1858 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
compressed or
Refrigerant gas R
1216.
Hexaldehyde......... 3 UN1207 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Hexamethylene 6.1 UN2281 II 6.1....... IB2, T7, TP2, None.......... 202........ 243........ 5 L 60 L C 13, 40
diisocyanate. TP13
Hexamethylene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
triperoxide diamine
(dry).
Hexamethylenediamine 8 UN2280 III 8......... IB8, IP3, T4, 154........... 213........ 240........ 25 kg 100 kg A 12
, solid. TP1
Hexamethylenediamine 8 UN1783 II 8......... IB2, T7, TP2 None.......... 202........ 242........ 1 L 30 L A .......
solution.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Hexamethyleneimine.. 3 UN2493 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 40
Hexamethylenetetrami 4.1 UN1328 III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A .......
ne.
Hexamethylol benzene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
hexanitrate.
Hexanes............. 3 UN1208 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
2,2',4,4',6,6'- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitro-3,3'-
dihydroxyazobenzene
(dry).
Hexanitroazoxy Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
benzene.
N,N'- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(hexanitrodiphenyl)
ethylene
dinitramine (dry).
Hexanitrodiphenyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
urea.
2,2',3',4,4',6- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrodiphenylam
ine.
Hexanitrodiphenylami 1.1D UN0079 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
ne or Dipicrylamine
or Hexyl.
2,3',4,4',6,6'- Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrodiphenylet
her.
Hexanitroethane..... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrooxanilide.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrostilbene... 1.1D UN0392 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
Hexanoic acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Corrosive liquids,
n.o.s..
Hexanols............ 3 UN2282 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
1-Hexene............ 3 UN2370 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
[[Page 180]]
Hexogen and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
cyclotetramethylene
tetranitramine
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Hexogen and HMX ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Hexogen and octogen ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixtures, wetted or
desensitized see
RDX and HMX
mixtures, wetted or
desensitized etc.
Hexogen, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Cyclotrimethylenetr
initramine, etc.
Hexolite, or Hexotol 1.1D UN0118 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
dry or wetted with
less than 15
percent water, by
mass.
Hexotonal........... 1.1D UN0393 II 1.1D...... None.......... 62......... None....... Forbidden Forbidden 10 .......
Hexyl, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanitrodiphenylam
ine.
Hexyltrichlorosilane 8 UN1784 II 8......... A7, B2, B6, IB2, None.......... 202........ 242........ Forbidden 30 L C 40
N34, T7, TP2,
TP13
High explosives, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
individual
explosives' entries.
HMX, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Cyclotetramethylene
te tranitramine,
etc.
Hydrazine, anhydrous 8 UN2029 I 8, 3, 6.1. A3, A6, A7, A10, None.......... 201........ 243........ Forbidden 2.5 L D 21, 40,
or Hydrazine B7, B16, B53 42, 100
aqueous solutions
with more than 64
percent hydrazine,
by mass.
Hydrazine, aqueous 6.1 UN3293 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
solution with not
more than 37
percent hydrazine,
by mass.
Hydrazine azide..... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hydrazine chlorate.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
[[Page 181]]
Hydrazine dicarbonic Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
acid diazide.
Hydrazine hydrate or 8 UN2030 II 8, 6.1.... B16, B53, IB2, None.......... 202........ 243........ Forbidden 30 L D 40, 42,
Hydrazine aqueous T7, TP2, TP13 82
solutions, with not
less than 37
percent but not
more than 64
percent hydrazine,
by mass.
Hydrazine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
perchlorate.
Hydrazine selenate.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Hydriodic acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
anhydrous, see
Hydrogen iodide,
anhydrous.
Hydriodic acid...... 8 UN1787 II 8......... A3, A6, B2, IB2, 154........... 202........ 242........ 1 L 30 L C .......
N41, T7, TP2
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L C 8
Hydrobromic acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
anhydrous, see
Hydrogen bromide,
anhydrous.
Hydrobromic acid, 8 UN1788 II 8......... B2, B15, IB2, 154........... 202........ 242........ Forbidden Forbidden C .......
with more than 49 N41, T7, TP2
percent hydrobromic
acid.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ Forbidden Forbidden C 8
Hydrobromic acid, 8 UN1788 II 8......... A3, A6, B2, B15, 154........... 202........ 242........ 1 L 30 L C .......
with not more than IB2, N41, T7,
49 percent TP2
hydrobromic acid.
.................... ........... .................. III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 30 L C 8
Hydrocarbon gas 2.1 UN1964 ....... 2.1....... 306........... 302........ 314, 315... Forbidden 150 kg E 40
mixture,
compressed, n.o.s..
Hydrocarbon gas 2.1 UN1965 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg E 40
mixture, liquefied,
n.o.s..
Hydrocarbons, 3 UN3295 I 3......... T11, TP1, TP8 150........... 201........ 243........ 1 L 30 L E .......
liquid, n.o.s..
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
Hydrochloric acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
anhydrous, see
Hydrogen chloride,
anhydrous.
Hydrochloric acid... 8 UN1789 II 8......... A3, A6, B3, B15, 154........... 202........ 242........ 1 L 30 L C .......
IB2, N41, T8,
TP2, TP12
.................... ........... .................. III 8......... IB3, T4, TP1, 154........... 203........ 241........ 5 L 60 L C 8
TP12
Hydrocyanic acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
anhydrous, see
Hydrogen cyanide
etc.
Hydrocyanic acid, 6.1 UN1613 I 6.1....... 2, B61, B65, None.......... 195........ 244........ Forbidden Forbidden D 40
aqueous solutions B77, B82, T20,
or Hydrogen TP2, TP13
cyanide, aqueous
solutions with not
more than 20
percent hydrogen
cyanide.
[[Page 182]]
D Hydrocyanic acid, 6.1 NA1613 II 6.1....... IB1, T14, TP2, None.......... 195........ 243........ Forbidden 5 L D 40
aqueous solutions TP13, TP27
with less than 5
percent hydrogen
cyanide.
Hydrocyanic acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
liquefied, see
Hydrogen cyanide,
etc.
Hydrocyanic acid Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(prussic),
unstabilized.
Hydrofluoric acid 8 UN1786 I 8, 6.1.... A6, A7, B15, None.......... 201........ 243........ Forbidden 2.5 L D 40
and Sulfuric acid B23, N5, N34,
mixtures. T10, TP2, TP12,
TP13
Hydrofluoric acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
anhydrous, see
Hydrogen fluoride,
anhydrous.
Hydrofluoric acid, 8 UN1790 I 8, 6.1.... A6, A7, B4, B15, None.......... 201........ 243........ 0.5 L 2.5 L D 12, 40
with more than 60 B23, N5, N34,
percent strength. T10, TP2, TP12,
TP13
Hydrofluoric acid, 8 UN1790 II 8, 6.1.... A6, A7, B15, None.......... 202........ 243........ 1 L 30 L D 12, 40
with not more than IB2, N5, N34,
60 percent strength. T8, TP2, TP12
Hydrofluoroboric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
acid, see
Fluoroboric acid.
Hydrofluorosilicic ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
acid, see
Fluorosilicic acid.
Hydrogen and Methane 2.1 UN2034 ....... 2.1....... 306........... 302........ 302, 314, Forbidden 150 kg E 40
mixtures, 315.
compressed.
Hydrogen bromide, 2.3 UN1048 ....... 2.3, 8.... 3, B14 None.......... 304........ 314, 315... Forbidden 25 kg D 40
anhydrous.
Hydrogen chloride, 2.3 UN1050 ....... 2.3, 8.... 3 None.......... 304........ None....... Forbidden Forbidden D 40
anhydrous.
Hydrogen chloride, 2.3 UN2186 ....... 2.3, 8.... 3, B6 None.......... None....... 314, 315... Forbidden Forbidden B 40
refrigerated liquid.
Hydrogen, compressed 2.1 UN1049 ....... 2.1....... 306........... 302........ 302, 314... Forbidden 150 kg E 40, 57
Hydrogen cyanide, 6.1 UN3294 I 6.1, 3.... 2, 25, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
solution in alcohol B32, B74, T20,
with not more than TP2, TP13, TP38,
45 percent hydrogen TP45
cyanide.
[[Page 183]]
Hydrogen cyanide, 6.1 UN1051 I 6.1, 3.... 1, B35, B61, None.......... 195........ 244........ Forbidden Forbidden D 40
stabilized with B65, B77, B82
less than 3 percent
water.
Hydrogen cyanide, 6.1 UN1614 I 6.1....... 5 None.......... 195........ None....... Forbidden Forbidden D 25, 40
stabilized, with
less than 3 percent
water and absorbed
in a porous inert
material.
Hydrogen fluoride, 8 UN1052 I 8, 6.1.... 3, B7, B46, B71, None.......... 163........ 243........ Forbidden Forbidden D 40
anhydrous. B77, T10, TP2
Hydrogen iodide, 2.3 UN2197 ....... 2.3....... 3, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
anhydrous.
Hydrogen iodide ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solution, see
Hydriodic acid,
solution.
Hydrogen peroxide 5.1 UN3149 II 5.1, 8.... A2, A3, A6, B53, None.......... 202........ 243........ 1 L 5 L D 25, 66,
and peroxyacetic IB2, IP5, T7, 75, 106
acid mixtures, TP2, TP6, TP24
stabilized with
acids, water and
not more than 5
percent
peroxyacetic acid.
Hydrogen peroxide, 5.1 UN2014 II 5.1, 8.... 12, A3, A6, B53, None.......... 202........ 243........ Forbidden Forbidden D 25, 66,
aqueous solutions B80, B81, B85, 75, 106
with more than 40 IB2, IP5, T7,
percent but not TP2, TP6, TP24
more than 60
percent hydrogen
peroxide
(stabilized as
necessary).
Hydrogen peroxide, 5.1 UN2014 II 5.1, 8.... A2, A3, A6, B53, None.......... 202........ 243........ 1 L 5 L D 25, 66,
aqueous solutions IB2, IP5, T7, 75, 106
with not less than TP2, TP6, TP24
20 percent but not
more than 40
percent hydrogen
peroxide
(stabilized as
necessary).
Hydrogen peroxide, 5.1 UN2984 III 5.1....... A1, IB2, IP5, 152........... 203........ 241........ 2.5 L 30 L B 25, 75,
aqueous solutions T4, TP1, TP6, 106
with not less than TP24
8 percent but less
than 20 percent
hydrogen peroxide
(stabilized as
necessary).
Hydrogen peroxide, 5.1 UN2015 I 5.1, 8.... 12, A3, A6, B53, None.......... 201........ 243........ Forbidden Forbidden D 25, 66,
stabilized or B80, B81, B85, 75, 106
Hydrogen peroxide T10, TP2, TP6,
aqueous solutions, TP24
stabilized with
more than 60
percent hydrogen
peroxide.
Hydrogen, 2.1 UN1966 ....... 2.1....... T75, TP5 None.......... 316........ 318, 319... Forbidden Forbidden D 40
refrigerated liquid
(cryogenic liquid).
Hydrogen selenide, 2.3 UN2202 ....... 2.3, 2.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
anhydrous.
Hydrogen sulfate, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Sulfuric acid.
Hydrogen sulfide.... 2.3 UN1053 ....... 2.3, 2.1.. 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
Hydrogendifluorides, 8 UN1740 II 8......... IB5, IP2, IP4, None.......... 212........ 240........ 15 kg 50 kg A 25, 26,
n.o.s. solid. N3, N34 40
.................... ........... .................. III 8......... IB8, IP3, N3, 154........... 213........ 240........ 25 kg 100 kg A 25, 26,
N34 40
[[Page 184]]
Hydrogendifluorides, 8 UN1740 II 8......... IB2, N3, N34 None.......... 202........ 242........ 1 L 30 L A 25, 26,
n.o.s. solutions. 40
.................... ........... .................. III 8......... IB3, IP3, N3, 154........... 203........ 241........ 5 L 60 L A 25, 26,
N34 40
Hydroquinone........ 6.1 UN2662 III 6.1....... IB8, IP3, T4, 153........... 213........ 240........ 100 kg 200 kg A .......
TP1
Hydrosilicofluoric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
acid, see
Fluorosilicic acid.
Hydroxyl amine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
iodide.
Hydroxylamine 8 UN2865 III 8......... IB8, IP3 154........... 213........ 240........ 25 kg 100 kg A .......
sulfate.
Hypochlorite 8 UN1791 II 8......... A7, B2, B15, 154........... 202........ 242........ 1 L 30 L B 26
solutions. IB2, IP5, N34,
T7, TP2, TP24
.................... ........... .................. III 8......... IB3, N34, T4, 154........... 203........ 241........ 5 L 60 L B 26
TP2, TP24
Hypochlorites, 5.1 UN3212 II 5.1....... IB8, IP2, IP4 152........... 212........ 240........ 5 kg 25 kg D 48, 56,
inorganic, n.o.s.. 58, 69,
106,
116,
118
Hyponitrous acid.... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Igniter fuse, metal ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
clad, see Fuse,
igniter, tubular,
metal clad.
Igniters............ 1.1G UN0121 II 1.1G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Igniters............ 1.2G UN0314 II 1.2G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Igniters............ 1.3G UN0315 II 1.3G...... None.......... 62......... None....... Forbidden Forbidden 07 .......
Igniters............ 1.4G UN0325 II 1.4G...... None.......... 62......... None....... Forbidden 75 kg 06 .......
Igniters............ 1.4S UN0454 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
3,3'- 8 UN2269 III 8......... IB3, T4, TP2 154........... 203........ 241........ 5 L 60 L A .......
Iminodipropylamine.
G Infectious 6.2 UN2900 ....... 6.2....... 134........... 196........ None....... 50 mL or 50 4 L or 4 kg B .......
substances, g
affecting animals
only.
G Infectious 6.2 UN2814 ....... 6.2....... 134........... 196........ None....... 50 mL or 50 4 L or 4 kg B .......
substances, g
affecting humans.
Inflammable, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Flammable.
Initiating Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
explosives (dry).
Inositol hexanitrate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
G Insecticide gases, 2.2 UN1968 ....... 2.2....... 306........... 304........ 314, 315... 75 kg 150 kg A .......
n.o.s..
[[Page 185]]
G Insecticide gases, 2.1 UN3354 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg D 40
flammable, n.o.s..
G Insecticide gases, 2.3 UN3355 ....... 2.3, 2.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
hazard Zone A.
G Insecticide gases, 2.3 UN3355 ....... 2.3, 2.1.. 2, B9, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
hazard Zone B.
G Insecticide gases, 2.3 UN3355 ....... 2.3, 2.1.. 3, B14 None.......... 302, 305... 314, 315... Forbidden Forbidden D .......
toxic, flammable,
n.o.s. Inhalation
hazard Zone C.
G Insecticide gases, 2.3 UN3355 ....... 2.3, 2.1.. 4 None.......... 302, 305... 314, 315... Forbidden Forbidden D .......
toxic, flammable,
n.o.s. Inhalation
hazard Zone D.
G Insecticide gases, 2.3 UN1967 ....... 2.3....... 3 None.......... 193, 334... 245........ Forbidden Forbidden D 40
toxic, n.o.s..
Inulin trinitrate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Iodine azide (dry).. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Iodine monochloride. 8 UN1792 II 8......... B6, IB8, IP2, None.......... 212........ 240........ Forbidden 50 kg D 40, 66,
IP4, N41, T7, 74, 89,
TP2 90
Iodine pentafluoride 5.1 UN2495 I 5.1, 6.1, None.......... 205........ 243........ Forbidden 2.5 L D 25, 40,
8. 66, 90
2-Iodobutane........ 3 UN2390 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Iodomethylpropanes.. 3 UN2391 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Iodopropanes........ 3 UN2392 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Iodoxy compounds Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Iridium Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitratopentamine
iridium nitrate.
Iron chloride, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Ferric chloride.
Iron oxide, spent, 4.2 UN1376 III 4.2....... B18, IB8, IP3 None.......... 213........ 240........ Forbidden Forbidden E .......
or Iron sponge,
spent obtained from
coal gas
purification.
Iron pentacarbonyl.. 6.1 UN1994 I 6.1, 3.... 1, B9, B14, B30, None.......... 192........ 244........ Forbidden Forbidden D 40
B72, B77, T22,
TP2, TP13, TP38,
TP44
Iron sesquichloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ferric chloride.
Irritating material, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Tear gas
substances, etc.
Isobutane see also 2.1 UN1969 ....... 2.1....... 19, T50 306........... 304........ 314, 315... Forbidden 150 kg E 40
Petroleum gases,
liquefied.
Isobutanol or 3 UN1212 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Isobutyl alcohol.
Isobutyl acetate.... 3 UN1213 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isobutyl acrylate, 3 UN2527 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
stabilized.
Isobutyl alcohol, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Isobutanol.
Isobutyl aldehyde, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see
Isobutyraldehyde.
[[Page 186]]
D Isobutyl 6.1 NA2742 I 6.1, 3, 8. 2, B9, B14, B32, None.......... 227........ 244........ 1 L 30 L A 12, 13,
chloroformate. B74, T20, TP4, 22, 25,
TP12, TP13, 40, 48,
TP38, TP45 100
Isobutyl formate.... 3 UN2393 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isobutyl isobutyrate 3 UN2528 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
+ Isobutyl isocyanate. 3 UN2486 I 3, 6.1.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
B72, T22, TP2,
TP13, TP27
Isobutyl 3 UN2283 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
methacrylate,
stabilized.
Isobutyl propionate. 3 UN2394 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L B .......
Isobutylamine....... 3 UN1214 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 40
Isobutylene see also 2.1 UN1055 ....... 2.1....... 19, T50 306........... 304........ 314, 315... Forbidden 150 kg E 40
Petroleum gases,
liquefied.
Isobutyraldehyde or 3 UN2045 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E 40
Isobutyl aldehyde.
Isobutyric acid..... 3 UN2529 III 3, 8...... B1, IB3, T4, TP1 150........... 203........ 242........ 5 L 60 L A .......
Isobutyronitrile.... 3 UN2284 II 3, 6.1.... IB2, T7, TP2, None.......... 202........ 243........ 1 L 60 L E 40
TP13
Isobutyryl chloride. 3 UN2395 II 3, 8...... IB1, T7, TP2 None.......... 202........ 243........ 1 L 5 L C 40
G Isocyanates, 3 UN2478 II 3, 6.1.... 5, A3, A7, IB2, None.......... 202........ 243........ 1 L 60 L D 40
flammable, toxic, T11, TP2, TP13,
n.o.s. or TP27
Isocyanate
solutions,
flammable, toxic,
n.o.s. flash point
less than 23
degrees C.
G Isocyanates, toxic, 6.1 UN3080 II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 25, 40,
flammable, n.o.s. TP13, TP27 48
or Isocyanate
solutions, toxic,
flammable, n.o.s.,
flash point not
less than 23
degrees C but not
more than 61
degrees C and
boiling point less
than 300 degrees C.
G Isocyanates, toxic, 6.1 UN2206 II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L E 25, 40,
n.o.s. or TP13, TP27 48
Isocyanate
solutions, toxic,
n.o.s., flash point
more than 61
degrees C and
boiling point less
than 300 degrees C.
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L E 25, 40,
TP13, TP28 48
[[Page 187]]
Isocyanatobenzotrifl 6.1 UN2285 II 6.1, 3.... 5, IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L D 25, 40,
uorides. 48
Isoheptenes......... 3 UN2287 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isohexenes.......... 3 UN2288 II 3......... IB2, IP8, T11, 150........... 202........ 242........ 5 L 60 L E .......
TP1
Isooctane, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Octanes.
Isooctenes.......... 3 UN1216 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isopentane, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Pentane.
Isopentanoic acid, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Corrosive
liquids, n.o.s..
Isopentenes......... 3 UN2371 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E .......
Isophorone 6.1 UN2290 III 6.1....... IB3, T4, TP2 153........... 203........ 241........ 60 L 220 L B 40
diisocyanate.
Isophoronediamine... 8 UN2289 III 8......... IB3, T4, TP1 154........... 203........ 241........ 5 L 60 L A .......
Isoprene, stabilized 3 UN1218 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E .......
Isopropanol or 3 UN1219 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isopropyl alcohol.
Isopropenyl acetate. 3 UN2403 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isopropenylbenzene.. 3 UN2303 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Isopropyl acetate... 3 UN1220 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isopropyl acid 8 UN1793 III 8......... IB8, IP3, T4, 154........... 213........ 240........ 25 kg 100 kg A .......
phosphate. TP1
Isopropyl alcohol, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Isopropanol.
Isopropyl butyrate.. 3 UN2405 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Isopropyl 3 UN2947 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
chloroacetate.
Isopropyl 6.1 UN2407 I 6.1, 3, 8. 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden B 40
chloroformate. B74, B77, T20,
TP2, TP13, TP38,
TP44
Isopropyl 2- 3 UN2934 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
chloropropionate.
Isopropyl 3 UN2406 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
isobutyrate.
+ Isopropyl isocyanate 3 UN2483 I 3, 6.1.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
B72, T22, TP2,
TP13, TP38, TP44
Isopropyl mercaptan, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Propanethiols.
Isopropyl nitrate... 3 UN1222 II 3......... IB2, IP7 150........... 202........ None....... 5 L 60 L D .......
Isopropyl phosphoric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
acid, see Isopropyl
acid phosphate.
Isopropyl propionate 3 UN2409 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Isopropylamine...... 3 UN1221 I 3, 8...... T11, TP2 None.......... 201........ 243........ 0.5 L 2.5 L E .......
Isopropylbenzene.... 3 UN1918 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Isopropylcumyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
hydroperoxide, with
more than 72
percent in solution.
Isosorbide dinitrate 4.1 UN2907 II 4.1....... IB6, IP2 None.......... 212........ None....... 15 kg 50 kg E .......
mixture with not
less than 60
percent lactose,
mannose, starch or
calcium hydrogen
phosphate.
Isosorbide-5- 4.1 UN3251 III 4.1....... 66, IB8 151........... 213........ 240........ Forbidden Forbidden D 12
mononitrate.
Isothiocyanic acid.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
[[Page 188]]
Jet fuel, see Fuel ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
aviation, turbine
engine.
D Jet perforating 1.1D NA0124 II 1.1D...... 55, 56 None.......... 62......... None....... Forbidden Forbidden 07 .......
guns, charged oil
well, with
detonator.
D Jet perforating 1.4D NA0494 II 1.4D...... 55, 56 None.......... 62......... None....... Forbidden Forbidden 06 .......
guns, charged oil
well, with
detonator.
Jet perforating 1.1D UN0124 II 1.1D...... 55 None.......... 62......... None....... Forbidden Forbidden 07 .......
guns, charged oil
well, without
detonator.
Jet perforating 1.4D UN0494 II 1.4D...... 55, 114 None.......... 62......... None....... Forbidden 300 kg 06 .......
guns, charged, oil
well, without
detonator.
Jet perforators, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Charges, shaped,
etc.
Jet tappers, without ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
detonator, see
Charges, shaped,
etc.
Jet thrust igniters, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
for rocket motors
or Jato, see
Igniters.
Jet thrust unit ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
(Jato), see Rocket
motors.
Kerosene............ 3 UN1223 III 3......... B1, IB3, T2, TP2 150........... 203........ 242........ 60 L 220 L A .......
G Ketones, liquid, 3 UN1224 I 3......... T11, TP1, TP8, None.......... 201........ 243........ 1 L 30 L E .......
n.o.s.. TP27
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B .......
TP8, TP28
.................... ........... .................. III 3......... B1, IB3, T4, 150........... 203........ 242........ 60 L 220 L A .......
TP1, TP29
Krypton, compressed. 2.2 UN1056 ....... 2.2....... 306........... 302........ None....... 75 kg 150 kg A .......
Krypton, 2.2 UN1970 ....... 2.2....... T75, TP5 320........... None....... None....... 50 kg 500 kg B .......
refrigerated liquid
(cryogenic liquid).
Lacquer base or ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
lacquer chips,
nitrocellulose,
dry, see
Nitrocellulose,
etc. (UN 2557).
Lacquer base or ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
lacquer chips,
plastic, wet with
alcohol or solvent,
see Nitrocellulose
(UN2059, UN2555,
UN2556, UN2557) or
Paint etc.(UN1263).
Lead acetate........ 6.1 UN1616 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
Lead arsenates...... 6.1 UN1617 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
[[Page 189]]
Lead arsenites...... 6.1 UN1618 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Lead azide (dry).... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Lead azide, wetted 1.1A UN0129 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
with not less than
20 percent water or
mixture of alcohol
and water, by mass.
Lead compounds, 6.1 UN2291 III 6.1....... 138, IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
soluble, n.o.s..
Lead cyanide........ 6.1 UN1620 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 26
Lead dioxide........ 5.1 UN1872 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
Lead dross, see Lead ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
sulfate, with more
than 3 percent free
acid.
Lead nitrate........ 5.1 UN1469 II 5.1, 6.1.. IB8, IP2, IP4 None.......... 212........ 242........ 5 kg 25 kg A .......
Lead Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitroresorcinate
(dry).
Lead perchlorate, 5.1 UN1470 II 5.1, 6.1.. IB6, IP2, T4, None.......... 212........ 242........ 5 kg 25 kg A 56, 58,
solid. TP1 106
Lead perchlorate, 5.1 UN1470 II 5.1, 6.1.. IB1, T4, TP1 None.......... 202........ 243........ 1 L 5 L A 56, 58,
solution. 106
Lead peroxide, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Lead dioxide.
Lead phosphite, 4.1 UN2989 II 4.1....... IB8, IP2, IP4 None.......... 212........ 240........ 5 kg 25 kg B 34
dibasic.
.................... ........... .................. III 4.1....... IB8, IP3 151........... 213........ 240........ 15 kg 50 kg B 34
Lead picrate (dry).. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Lead styphnate (dry) Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Lead styphnate, 1.1A UN0130 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
wetted or Lead
trinitroresorcinate
, wetted with not
less than 20
percent water or
mixture of alcohol
and water, by mass.
Lead sulfate with 8 UN1794 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
more than 3 percent
free acid.
Lead ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
trinitroresorcinate
, see Lead
styphnate, etc.
Life-saving 9 UN3072 ....... None...... 143 None.......... 219........ None....... No limit No limit A .......
appliances, not
self inflating
containing
dangerous goods as
equipment.
Life-saving 9 UN2990 ....... None...... None.......... 219........ None....... No limit No limit A .......
appliances, self
inflating.
Lighter replacement ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
cartridges
containing
liquefied petroleum
gases (and similar
devices, each not
exceeding 65
grams), see
Lighters or lighter
refills etc.
containing
flammable gas.
Lighters, fuse...... 1.4S UN0131 II 1.4S...... None.......... 62......... None....... 25 kg 100 kg 05 .......
Lighters or Lighter 2.1 UN1057 ....... 2.1....... N10 None.......... 21, 308.... None....... 1 kg 15 kg B 40
refills cigarettes,
containing
flammable gas.
[[Page 190]]
Lime, unslaked, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Calcium oxide.
G Liquefied gas, 2.1 UN3161 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg D 40
flammable, n.o.s..
G Liquefied gas, 2.2 UN3163 ....... 2.2....... T50 306........... 304........ 314, 315... 75 kg 150 kg A .......
n.o.s..
G Liquefied gas, 2.2 UN3157 ....... 2.2, 5.1.. 306........... 304........ 314, 315... 75 kg 150 kg D .......
oxidizing, n.o.s..
G I Liquefied gas, 2.3 UN3308 ....... 2.3, 8.... 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone A.
G I Liquefied gas, 2.3 UN3308 ....... 2.3, 8.... 2 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone B.
G I Liquefied gas, 2.3 UN3308 ....... 2.3, 8.... 3 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone C.
G I Liquefied gas, 2.3 UN3308 ....... 2.3, 8.... 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, corrosive,
n.o.s. Inhalation
Hazard Zone D.
G I Liquefied gas, 2.3 UN3309 ....... 2.3, 2.1, 1 None.......... 192........ 245........ Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone A.
G I Liquefied gas toxic, 2.3 UN3309 ....... 2.3, 2.1, 2 None.......... 304........ 314, 315... Forbidden Forbidden D 17, 40
flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone B.
G I Liquefied gas, 2.3 UN3309 ....... 2.3, 2.1, 3 None.......... 304........ 314, 315... Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone C.
G I Liquefied gas, 2.3 UN3309 ....... 2.3, 2.1, 4 None.......... 304........ 314, 315... Forbidden Forbidden D 17, 40
toxic, flammable, 8.
corrosive, n.o.s.
Inhalation Hazard
Zone D.
G Liquefied gas, 2.3 UN3160 ....... 2.3, 2.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone A.
G Liquefied gas, 2.3 UN3160 ....... 2.3, 2.1.. 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone B.
[[Page 191]]
G Liquefied gas, 2.3 UN3160 ....... 2.3, 2.1.. 3, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone C.
G Liquefied gas, 2.3 UN3160 ....... 2.3, 2.1.. 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, flammable,
n.o.s. Inhalation
Hazard Zone D.
G Liquefied gas, 2.3 UN3162 ....... 2.3....... 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone A.
G Liquefied gas, 2.3 UN3162 ....... 2.3....... 2, B9, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone B.
G Liquefied gas, 2.3 UN3162 ....... 2.3....... 3, B14 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone C.
G Liquefied gas, 2.3 UN3162 ....... 2.3....... 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, n.o.s.
Inhalation Hazard
Zone D.
G I Liquefied gas, 2.3 UN3310 ....... 2.3, 5.1, 1 None.......... 192........ 245........ Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone A.
G I Liquefied gas, 2.3 UN3310 ....... 2.3, 2.1, 2 None.......... 304........ 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone B.
G I Liquefied gas, 2.3 UN3310 ....... 2.3, 2.1, 3 None.......... 304........ 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone C.
G I Liquefied gas, 2.3 UN3310 ....... 2.3, 2.1, 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40, 89,
toxic, oxidizing, 8. 90
corrosive, n.o.s.
Inhalation Hazard
Zone D.
G Liquefied gas, 2.3 UN3307 ....... 2.3, 5.1.. 1 None.......... 192........ 245........ Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone A.
G Liquefied gas, 2.3 UN3307 ....... 2.3, 5.1.. 2 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone B.
G Liquefied gas, 2.3 UN3307 ....... 2.3, 5.1.. 3 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone C.
G Liquefied gas, 2.3 UN3307 ....... 2.3, 5.1.. 4 None.......... 304........ 314, 315... Forbidden Forbidden D 40
toxic, oxidizing,
n.o.s. Inhalation
Hazard Zone D.
Liquefied gases, non- 2.2 UN1058 ....... 2.2....... 306........... 304........ None....... 75 kg 150 kg A .......
flammable charged
with nitrogen,
carbon dioxide or
air.
Liquefied ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydrocarbon gas,
see Hydrocarbon gas
mixture, liquefied,
n.o.s..
Liquefied natural ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gas, see Methane,
etc. (UN 1972).
Liquefied petroleum ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gas see Petroleum
gases, liquefied.
Lithium............. 4.3 UN1415 I 4.3....... A7, A19, IB1, None.......... 211........ 244........ Forbidden 15 kg E .......
IP1, N45
[[Page 192]]
Lithium acetylide ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
ethylenediamine
complex, see Water
reactive solid etc.
Lithium alkyls...... 4.2 UN2445 I 4.2, 4.3.. B11, T21, TP2, None.......... 181........ 244........ Forbidden Forbidden D .......
TP7
Lithium aluminum 4.3 UN1410 I 4.3....... A19 None.......... 211........ 242........ Forbidden 15 kg E .......
hydride.
Lithium aluminum 4.3 UN1411 I 4.3, 3.... A2, A3, A11, N34 None.......... 201........ 244........ Forbidden 1 L D 40
hydride, ethereal.
Lithium batteries, 9 UN3091 II 9......... 29 185(i)........ 185........ None....... 5 kg 5 kg A .......
contained in
equipment.
Lithium batteries 9 UN3091 II 9......... 29 185........... 185........ None....... 5 kg gross 35 kg gross A .......
packed with
equipment.
Lithium battery..... 9 UN3090 II 9......... 29 185........... 185........ None....... 5 kg gross 35 kg gross A .......
Lithium borohydride. 4.3 UN1413 I 4.3....... A19, N40 None.......... 211........ 242........ Forbidden 15 kg E .......
Lithium ferrosilicon 4.3 UN2830 II 4.3....... A19, IB7, IP2 151........... 212........ 241........ 15 kg 50 kg E 40, 85,
103
Lithium hydride..... 4.3 UN1414 I 4.3....... A19, N40 None.......... 211........ 242........ Forbidden 15 kg E .......
Lithium hydride, 4.3 UN2805 II 4.3....... A8, A19, A20, 151........... 212........ 241........ 15 kg 50 kg E .......
fused solid. IB4
Lithium hydroxide, 8 UN2680 II 8......... IB8, IP2, IP4 154........... 212........ 240........ 15 kg 50 kg A .......
monohydrate or
Lithium hydroxide,
solid.
Lithium hydroxide, 8 UN2679 II 8......... B2, IB2, T7, TP2 154........... 202........ 242........ 1 L 30 L A .......
solution.
.................... ........... .................. III 8......... IB3, T4, TP2 154........... 203........ 241........ 5 L 60 L A 96
Lithium 5.1 UN1471 II 5.1....... A9, IB8, IP2, 152........... 212........ 240........ 5 kg 25 kg A 48, 56,
hypochlorite, dry IP4, N34 58, 69,
with more than 39% 106,
available chlorine 116
(8.8% available
oxygen) or Lithium
hypochlorite
mixtures, dry with
more than 39%
available chlorine
(8.8% available
oxygen).
Lithium in ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
cartridges, see
Lithium.
Lithium nitrate..... 5.1 UN2722 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
Lithium nitride..... 4.3 UN2806 I 4.3....... A19, IB4, IP1, None.......... 211........ 242........ Forbidden 15 kg E .......
N40
Lithium peroxide.... 5.1 UN1472 II 5.1....... A9, IB6, IP2, 152........... 212........ None....... 5 kg 25 kg A 13, 75,
N34 106
Lithium silicon..... 4.3 UN1417 II 4.3....... A19, A20, IB7, 151........... 212........ 241........ 15 kg 50 kg A 85, 103
IP2
[[Page 193]]
LNG, see Methane ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
etc. (UN 1972).
London purple....... 6.1 UN1621 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
LPG, see Petroleum ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
gases, liquefied.
Lye, see Sodium ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydroxide,
solutions.
Magnesium alkyls.... 4.2 UN3053 I 4.2, 4.3.. B11, T21, TP2, None.......... 181........ 244........ Forbidden Forbidden D 18
TP7
Magnesium aluminum 4.3 UN1419 I 4.3, 6.1.. A19, N34, N40 None.......... 211........ 242........ Forbidden 15 kg E 40, 85
phosphide.
+ Magnesium arsenate.. 6.1 UN1622 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Magnesium bisulfite ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
solution, see
Bisulfites, aqueous
solutions, n.o.s..
Magnesium bromate... 5.1 UN1473 II 5.1....... A1, IB8, IP4 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
106
Magnesium chlorate.. 5.1 UN2723 II 5.1....... IB8, IP2, IP4 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
106
Magnesium diamide... 4.2 UN2004 II 4.2....... A8, A19, A20, None.......... 212........ 241........ 15 kg 50 kg C .......
IB6
Magnesium diphenyl.. 4.2 UN2005 I 4.2....... None.......... 187........ 244........ Forbidden Forbidden C .......
Magnesium dross, wet Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
or hot.
Magnesium 6.1 UN2853 III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 26
fluorosilicate.
Magnesium granules, 4.3 UN2950 III 4.3....... A1, A19, IB8, 151........... 213........ 240........ 25 kg 100 kg A .......
coated, particle IP4
size not less than
149 microns.
Magnesium hydride... 4.3 UN2010 I 4.3....... A19, N40 None.......... 211........ 242........ Forbidden 15 kg E .......
Magnesium or 4.1 UN1869 III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A 39
Magnesium alloys
with more than 50
percent magnesium
in pellets,
turnings or ribbons.
Magnesium nitrate... 5.1 UN1474 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
Magnesium 5.1 UN1475 II 5.1....... IB6, IP2 152........... 212........ 242........ 5 kg 25 kg A 56, 58,
perchlorate. 106
Magnesium peroxide.. 5.1 UN1476 II 5.1....... IB6, IP2 152........... 212........ 242........ 5 kg 25 kg A 13, 75,
106
Magnesium phosphide. 4.3 UN2011 I 4.3, 6.1.. A19, N40 None.......... 211........ None....... Forbidden 15 kg E 40, 85
Magnesium, powder or 4.3 UN1418 I 4.3, 4.2.. A19, B56 None.......... 211........ 244........ Forbidden 15 kg A 39
Magnesium alloys,
powder.
.................... ........... .................. II 4.3, 4.2.. A19, B56, IB5, None.......... 212........ 241........ 15 kg 50 kg A 39
IP2
.................... ........... .................. III 4.3, 4.2.. A19, B56, IB8, None.......... 213........ 241........ 25 kg 100 kg A 39
IP4
Magnesium scrap, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Magnesium, etc. (UN
1869).
Magnesium silicide.. 4.3 UN2624 II 4.3....... A19, A20, IB7, 151........... 212........ 241........ 15 kg 50 kg B 85, 103
IP2
[[Page 194]]
Magnetized material, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Sec. 173.21.
Maleic anhydride.... 8 UN2215 III 8......... IB8, IP3, T4, 154........... 213........ 240........ 25 kg 100 kg A .......
TP1
Malononitrile....... 6.1 UN2647 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 12
Mancozeb (manganese ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
ethylenebisdithioca
rbamate complex
with zinc) see
Maneb.
Maneb or Maneb 4.2 UN2210 III 4.2, 4.3.. 57, A1, A19, IB6 None.......... 213........ 242........ 25 kg 100 kg A 34
preparations with
not less than 60
percent maneb.
Maneb stabilized or 4.3 UN2968 III 4.3....... 54, A1, A19, 151........... 213........ 242........ 25 kg 100 kg B 34
Maneb preparations, IB8, IP4
stabilized against
self-heating.
Manganese nitrate... 5.1 UN2724 III 5.1....... A1, IB8, IP3 152........... 213........ 240........ 25 kg 100 kg A .......
Manganese resinate.. 4.1 UN1330 III 4.1....... A1, IB6 151........... 213........ 240........ 25 kg 100 kg A .......
Mannitan Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetranitrate.
Mannitol hexanitrate Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Mannitol 1.1D UN0133 II 1.1D...... 121 None.......... 62......... None....... Forbidden Forbidden 10 .......
hexanitrate, wetted
or Nitromannite,
wetted with not
less than 40
percent water, or
mixture of alcohol
and water, by mass.
Marine pollutants, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
liquid or solid,
n.o.s., see
Environmentally
hazardous
substances, liquid
or solid, n.o.s..
Matches, block, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Matches, 'strike
anywhere'.
Matches, fusee...... 4.1 UN2254 III 4.1....... 186........... 186........ None....... Forbidden Forbidden A .......
Matches, safety 4.1 UN1944 III 4.1....... 186........... 186........ None....... 25 kg 100 kg A .......
(book, card or
strike on box).
Matches, strike 4.1 UN1331 III 4.1....... 186........... 186........ None....... Forbidden Forbidden B .......
anywhere.
Matches, wax, Vesta. 4.1 UN1945 III 4.1....... 186........... 186........ None....... 25 kg 100 kg B .......
Matting acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Sulfuric acid.
Medicine, liquid, 3 UN3248 II 3, 6.1.... 36, IB2 None.......... 202........ None....... 1 L 5 L B 40
flammable, toxic,
n.o.s..
.................... ........... .................. III 3, 6.1.... 36, IB3 150........... 203........ None....... 5 L 5 L A .......
Medicine, liquid, 6.1 UN1851 II 6.1....... 153........... 202........ 243........ 5 L 5 L C 40
toxic, n.o.s..
.................... ........... .................. III 6.1....... 153........... 203........ 241........ 5 L 5 L C 40
[[Page 195]]
Medicine, solid, 6.1 UN3249 II 6.1....... 36 153........... 212........ None....... 5 kg 5 kg C 40
toxic, n.o.s..
.................... ........... .................. III 6.1....... 36 153........... 213........ None....... 5 kg 5 kg C 40
Memtetrahydrophthali ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
c anhydride, see
Corrosive liquids,
n.o.s..
Mercaptans, liquid, 3 UN3336 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E 95
flammable, n.o.s.
or Mercaptan
mixture, liquid,
flammable, n.o.s..
.................... ........... .................. II 3......... IB2, T7, TP1, 150........... 202........ 242........ 5 L 60 L B 95
TP8, TP28
.................... ........... .................. III 3......... B1, B52, IB3, 150........... 203........ 241........ 60 L 220 L B 95
T4, TP1, TP29
Mercaptans, liquid, 3 UN1228 II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ Forbidden 60 L B 40, 95
flammable, toxic, TP27
n.o.s. or Mercaptan
mixtures, liquid,
flammable, toxic,
n.o.s..
.................... ........... .................. III 3, 6.1.... B1, IB3, T7, 150........... 203........ 242........ 5 L 220 L A 40, 95
TP1, TP28
Mercaptans, liquid, 6.1 UN3071 II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L C 40, 121
toxic, flammable, TP13, TP27
n.o.s. or Mercaptan
mixtures, liquid,
toxic, flammable,
n.o.s., flash point
not less than 23
degrees C.
5-Mercaptotetrazol-1- 1.4C UN0448 II 1.4C...... None.......... 62......... None....... Forbidden 75 kg 09 .......
acetic acid.
Mercuric arsenate... 6.1 UN1623 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercuric chloride... 6.1 UN1624 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercuric compounds, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Mercury
compounds, etc.
Mercuric nitrate.... 6.1 UN1625 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......
N73
+ Mercuric potassium 6.1 UN1626 I 6.1....... IB7, IP1, N74, None.......... 211........ 242........ 5 kg 50 kg A 26
cyanide. N75
Mercuric ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
sulfocyanate, see
Mercury thiocyanate.
Mercurol, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Mercury nucleate.
Mercurous azide..... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Mercurous compounds, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Mercury
compounds, etc.
Mercurous nitrate... 6.1 UN1627 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
A W Mercury............. 8 UN2809 III 8......... 164........... 164........ 240........ 35 kg 35 kg B 40, 97
Mercury acetate..... 6.1 UN1629 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury acetylide... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Mercury ammonium 6.1 UN1630 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
chloride.
Mercury based 3 UN2778 I 3, 6.1.... T14, TP2, TP13, None.......... 201........ 243........ Forbidden 30 L B 40
pesticides, liquid, TP27
flammable, toxic,
flash point less
than 23 degrees C.
.................... ........... .................. II 3, 6.1.... IB2, T11, TP2, None.......... 202........ 243........ 1 L 60 L B 40
TP13, TP27
Mercury based 6.1 UN3012 I 6.1....... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic.
[[Page 196]]
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1....... IB3, T7, TP2, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Mercury based 6.1 UN3011 I 6.1, 3.... T14, TP2, TP13, None.......... 201........ 243........ 1 L 30 L B 40
pesticides, liquid, TP27
toxic, flammable,
flash point not
less than 23
degrees C.
.................... ........... .................. II 6.1, 3.... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP13, TP27
.................... ........... .................. III 6.1, 3.... IB3, T7, TP2, 153........... 203........ 242........ 60 L 220 L A 40
TP28
Mercury based 6.1 UN2777 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A 40
pesticides, solid,
toxic.
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 40
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A 40
Mercury benzoate.... 6.1 UN1631 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury bromides.... 6.1 UN1634 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury compounds, 6.1 UN2024 I 6.1....... None.......... 201........ 243........ 1 L 30 L B 40
liquid, n.o.s..
.................... ........... .................. II 6.1....... IB2 None.......... 202........ 243........ 5 L 60 L B 40
.................... ........... .................. III 6.1....... IB3 153........... 203........ 241........ 60 L 220 L B 40
Mercury compounds, 6.1 UN2025 I 6.1....... IB7, IP1 None.......... 211........ 242........ 5 kg 50 kg A .......
solid, n.o.s..
.................... ........... .................. II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
.................... ........... .................. III 6.1....... IB8, IP3 153........... 213........ 240........ 100 kg 200 kg A .......
A Mercury contained in 8 UN2809 III 8......... None.......... 164........ None....... No limit No limit B 40, 97
manufactured
articles.
Mercury cyanide..... 6.1 UN1636 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A 26
N74, N75
Mercury fulminate, 1.1A UN0135 II 1.1A...... 111, 117 None.......... 62......... None....... Forbidden Forbidden 12 .......
wetted with not
less than 20
percent water, or
mixture of alcohol
and water, by mass.
Mercury gluconate... 6.1 UN1637 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury iodide, 6.1 UN1638 II 6.1....... IB2, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
solid.
Mercury iodide Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
aquabasic
ammonobasic (Iodide
of Millon's base).
Mercury iodide, 6.1 UN1638 II 6.1....... IB8, IP2, IP4 None.......... 202........ 243........ 5 L 60 L A .......
solution.
[[Page 197]]
Mercury nitride..... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Mercury nucleate.... 6.1 UN1639 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury oleate...... 6.1 UN1640 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury oxide....... 6.1 UN1641 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury oxycyanide.. Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Mercury oxycyanide, 6.1 UN1642 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A 26, 91
desensitized.
Mercury potassium 6.1 UN1643 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
iodide.
Mercury salicylate.. 6.1 UN1644 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
+ Mercury sulfates.... 6.1 UN1645 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mercury thiocyanate. 6.1 UN1646 II 6.1....... IB8, IP2, IP4 None.......... 212........ 242........ 25 kg 100 kg A .......
Mesityl oxide....... 3 UN1229 III 3......... B1, IB3, T2, TP1 None.......... 203........ 242........ 60 L 220 L A .......
Metal alkyl halides, 4.2 UN3049 I 4.2, 4.3.. B9, B11, T21, None.......... 181........ 244........ Forbidden Forbidden D .......
water-reactive TP2, TP7
n.o.s. or Metal
aryl halides, water-
reactive, n.o.s..
Metal alkyl 4.2 UN3050 I 4.2, 4.3.. B9, B11, T21, None.......... 181........ 244........ Forbidden Forbidden D .......
hydrides, water- TP2, TP7
reactive, n.o.s. or
Metal aryl
hydrides, water-
reactive, n.o.s..
Metal alkyls, water- 4.2 UN2003 I 4.2, 4.3.. B11, T21, TP2, None.......... 181........ 244........ Forbidden Forbidden D .......
reactive, n.o.s. or TP7
Metal aryls, water-
reactive n.o.s..
Metal carbonyls, 6.1 UN3281 I 6.1....... 5, T14, TP2, None.......... 201........ 243........ 1 L 30 L B 40
n.o.s.. TP13, TP27
.................... ........... .................. II 6.1....... IB2, T11, TP2, None.......... 202........ 243........ 5 L 60 L B 40
TP27
.................... ........... .................. III 6.1....... IB3, T7, TP1, 153........... 203........ 241........ 60 L 220 L A 40
TP28
Metal catalyst, dry. 4.2 UN2881 I 4.2....... N34 None.......... 187........ None....... 25 kg 100 kg C .......
.................... ........... .................. II 4.2....... IB6, IP2, N34 None.......... 187........ 242........ Forbidden 50 kg C .......
.................... ........... .................. III 4.2....... IB8, IP3, N34 None.......... 187........ 241........ 25 kg 100 kg C .......
Metal catalyst, 4.2 UN1378 II 4.2....... A2, A8, IB1, N34 None.......... 212........ None....... Forbidden 50 kg C .......
wetted with a
visible excess of
liquid.
Metal hydrides, 4.1 UN3182 II 4.1....... A1, IB4 151........... 212........ 240........ 15 kg 50 kg E .......
flammable, n.o.s..
.................... ........... .................. III 4.1....... A1, IB4 151........... 213........ 240........ 25 kg 100 kg E .......
Metal hydrides, 4.3 UN1409 I 4.3....... A19, N34, N40 None.......... 211........ 242........ Forbidden 15 kg D .......
water reactive,
n.o.s..
.................... ........... .................. II 4.3....... A19, IB4, N34, 151........... 212........ 242........ 15 kg 50 kg D .......
N40
Metal powder, self- 4.2 UN3189 II 4.2....... IB6, IP2 None.......... 212........ 241........ 15 kg 50 kg C .......
heating, n.o.s..
.................... ........... .................. III 4.2....... IB8, IP3 None.......... 213........ 241........ 25 kg 100 kg C .......
Metal powders, 4.1 UN3089 II 4.1....... IB8, IP2, IP4 151........... 212........ 240........ 15 kg 50 kg B .......
flammable, n.o.s..
.................... ........... .................. III 4.1....... IB6 151........... 213........ 240........ 25 kg 100 kg B .......
Metal salts of Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
methyl nitramine
(dry).
G Metal salts of 4.1 UN3181 II 4.1....... A1, IB8, IP2, 151........... 212........ 240........ 15 kg 50 kg B 40
organic compounds, IP4
flammable, n.o.s..
.................... ........... .................. III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg B 40
[[Page 198]]
Metaldehyde......... 4.1 UN1332 III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A .......
G Metallic substance, 4.3 UN3208 I 4.3....... IB4 None.......... 211........ 242........ Forbidden 15 kg E 40
water-reactive,
n.o.s..
.................... ........... .................. II 4.3....... IB7, IP2 151........... 212........ 242........ 15 kg 50 kg E 40
.................... ........... .................. III 4.3....... IB8, IP4 151........... 213........ 241........ 25 kg 100 kg E 40
G Metallic substance, 4.3 UN3209 I 4.3, 4.2.. None.......... 211........ 242........ Forbidden 15 kg E 40
water-reactive,
self-heating,
n.o.s..
.................... ........... .................. II 4.3, 4.2.. IB5, IP2 None.......... 212........ 242........ 15 kg 50 kg E 40
.................... ........... .................. III 4.3, 4.2.. IB8, IP4 None.......... 213........ 242........ 25 kg 100 kg E 40
Methacrylaldehyde, 3 UN2396 II 3, 6.1.... 45, IB2, T7, None.......... 202........ 243........ 1 L 60 L E 40
stabilized. TP1, TP13
Methacrylic acid, 8 UN2531 II 8......... IB3, T4, TP1, 154........... 202........ 242........ 1 L 30 L A .......
stabilized. TP18
+ Methacrylonitrile, 3 UN3079 I 3, 6.1.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 12, 40,
stabilized. B74, T20, TP2, 48
TP13, TP38, TP45
Methallyl alcohol... 3 UN2614 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Methane and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
hydrogen, mixtures,
see Hydrogen and
methane, mixtures,
etc.
Methane, compressed 2.1 UN1971 ....... 2.1....... 306........... 302........ 302........ Forbidden 150 kg E 40
or Natural gas,
compressed (with
high methane
content).
Methane, 2.1 UN1972 ....... 2.1....... T75, TP5 None.......... None....... 318........ Forbidden Forbidden D 40
refrigerated liquid
(cryogenic liquid)
or Natural gas,
refrigerated liquid
(cryogenic liquid),
with high methane
content).
Methanesulfonyl 6.1 UN3246 I 6.1, 8.... 2, 25, B9, B14, None.......... 227........ 244........ Forbidden Forbidden D 40
chloride. B32, B74, T20,
TP2, TP12, TP13,
TP38, TP45
+ I Methanol............ 3 UN1230 II 3, 6.1.... IB2, T7, TP2 150........... 202........ 242........ 1 L 60 L B 40
D Methanol............ 3 UN1230 II 3......... IB2, T7, TP2 150........... 202........ 242........ 1 L 60 L B 40
Methazoic acid...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
[[Page 199]]
4-Methoxy-4- 3 UN2293 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
methylpentan-2-one.
1-Methoxy-2-propanol 3 UN3092 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
+ Methoxymethyl 3 UN2605 I 3, 6.1.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
isocyanate. B72, T22, TP2,
TP13, TP38, TP44
Methyl acetate...... 3 UN1231 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methyl acetylene and 2.1 UN1060 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
propadiene
mixtures,
stabilized.
Methyl acrylate, 3 UN1919 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L B .......
stabilized. TP13
Methyl alcohol, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Methanol.
Methyl allyl 3 UN2554 II 3......... IB2, T4, TP1, 150........... 202........ 242........ 5 L 60 L E .......
chloride. TP13
Methyl amyl ketone, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Amyl methyl
ketone.
Methyl bromide...... 2.3 UN1062 ....... 2.3....... 3, B14, T50 None.......... 193........ 314, 315... Forbidden 25 kg D 40
Methyl bromide and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chloropicrin
mixtures with more
than 2 percent
chloropicrin, see
Chloropicrin and
methyl bromide
mixtures.
Methyl bromide and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chloropicrin
mixtures with not
more than 2 percent
chloropicrin, see
Methyl bromide.
Methyl bromide and 6.1 UN1647 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden C 40
ethylene dibromide B74, N65, T20,
mixtures, liquid. TP2, TP13, TP38,
TP44
Methyl bromoacetate. 6.1 UN2643 II 6.1....... IB2, T7, TP2 None.......... 202........ 243........ 5 L 60 L D 40
2-Methyl-1-butene... 3 UN2459 I 3......... T11, TP2 None.......... 201........ 243........ 1 L 30 L E .......
2-Methyl-2-butene... 3 UN2460 II 3......... IB2, IP8, T7, None.......... 202........ 242........ 5 L 60 L E .......
TP1
3-Methyl-1-butene... 3 UN2561 I 3......... T11, TP2 None.......... 201........ 243........ 1 L 30 L E .......
Methyl tert-butyl 3 UN2398 II 3......... IB2, T7, TP1 150........... 202........ 242........ 5 L 60 L E .......
ether.
Methyl butyrate..... 3 UN1237 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methyl chloride, or 2.1 UN1063 ....... 2.1....... T50 306........... 304........ 314, 315... 5 kg 100 kg D 40
Refrigerant gas R
40.
Methyl chloride and ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chloropicrin
mixtures, see
Chloropicrin and
methyl chloride
mixtures.
Methyl chloride and 2.1 UN1912 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg D 40
methylene chloride
mixtures.
Methyl chloroacetate 6.1 UN2295 I 6.1, 3.... T14, TP2, TP13 None.......... 201........ 243........ 1 L 30 L D .......
Methyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
chlorocarbonate,
see Methyl
chloroformate.
Methyl chloroform, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see 1,1,1-
Trichloroethane.
[[Page 200]]
Methyl chloroformate 6.1 UN1238 I 6.1, 3, 8. 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 21, 40,
B72, N34, T22, 100
TP2, TP13, TP38,
TP44
Methyl chloromethyl 6.1 UN1239 I 6.1, 3.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 40
ether. B72, T22, TP2,
TP38, TP44
Methyl 2- 3 UN2933 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
chloropropionate.
Methyl 6.1 UN2299 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
dichloroacetate.
Methyl ethyl ether, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethyl methyl
ether.
Methyl ethyl ketone, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethyl methyl
ketone.
Methyl ethyl ketone Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
peroxide, in
solution with more
than 9 percent by
mass active oxygen.
2-Methyl-5- 6.1 UN2300 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
ethylpyridine.
Methyl fluoride, or 2.1 UN2454 ....... 2.1....... 306........... 304........ 314, 315... Forbidden 150 kg E 40
Refrigerant gas R
41.
Methyl formate...... 3 UN1243 I 3......... T11, TP2 150........... 201........ 243........ 1 L 30 L E .......
2-Methyl-2- 6.1 UN3023 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden D 40, 102
heptanethiol. B74, T20, TP2,
TP13, TP38, TP45
Methyl iodide....... 6.1 UN2644 I 6.1....... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A 12, 40
B74, T20, TP2,
TP13, TP38, TP45
Methyl isobutyl 3 UN2053 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
carbinol.
Methyl isobutyl 3 UN1245 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
ketone.
Methyl isobutyl Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
ketone peroxide, in
solution with more
than 9 percent by
mass active oxygen.
Methyl isocyanate... 6.1 UN2480 I 6.1, 3.... 1, B9, B14, B30, None.......... 226........ 244........ Forbidden Forbidden D 26, 40
B72, T22, TP2,
TP13, TP38, TP44
[[Page 201]]
Methyl isopropenyl 3 UN1246 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
ketone, stabilized.
Methyl 6.1 UN2477 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden A .......
isothiocyanate. B74, T20, TP2,
TP13, TP38, TP45
Methyl isovalerate.. 3 UN2400 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methyl magnesium 4.3 UN1928 I 4.3, 3.... None.......... 201........ 243........ Forbidden 1 L D .......
bromide, in ethyl
ether.
Methyl mercaptan.... 2.3 UN1064 ....... 2.3, 2.1.. 3, B7, B9, B14, None.......... 304........ 314, 315... Forbidden 25 kg D 40
T50
Methyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mercaptopropionalde
hyde, see Thia-4-
pentanal.
Methyl methacrylate 3 UN1247 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B 40
monomer, stabilized.
Methyl nitramine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(dry).
Methyl nitrate...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Methyl nitrite...... Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
Methyl norbornene ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
dicarboxylic
anhydride, see
Corrosive liquids,
n.o.s..
Methyl orthosilicate 6.1 UN2606 I 6.1, 3.... 2, B9, B14, B32, None.......... 227........ 244........ Forbidden Forbidden E 40
B74, T20, TP2,
TP13, TP38, TP45
D Methyl phosphonic 6.1 NA9206 I 6.1, 8.... 2, A3, B9, B14, None.......... 227........ 244........ Forbidden Forbidden C .......
dichloride. B32, B74, N34,
N43, T20, TP4,
TP12, TP13,
TP38, TP45
Methyl ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
phosphonothioic
dichloride,
anhydrous, see
Corrosive liquid,
n.o.s..
D Methyl phosphonous 6.1 NA2845 I 6.1, 4.2.. 2, B9, B14, B16, None.......... 227........ 244........ Forbidden Forbidden D 18
dichloride, B32, B74, T20,
pyrophoric liquid. TP4, TP12, TP13,
TP38, TP45
Methyl picric acid Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(heavy metal salts
of).
Methyl propionate... 3 UN1248 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methyl propyl ether. 3 UN2612 II 3......... IB2, IP8, T7, 150........... 202........ 242........ 5 L 60 L E 40
TP2
Methyl propyl ketone 3 UN1249 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methyl sulfate, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Dimethyl sulfate.
Methyl sulfide, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Dimethyl sulfide.
Methyl 6.1 UN2533 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
trichloroacetate.
[[Page 202]]
Methyl trimethylol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
methane trinitrate.
Methyl vinyl ketone, 6.1 UN1251 I 6.1, 3, 8. 1, 25, B9, B14, None.......... 226........ 244........ Forbidden Forbidden B 40
stabilized. B30, B72, T22,
TP2, TP13, TP38,
TP44
Methylal............ 3 UN1234 II 3......... IB2, IP8, T7, None.......... 202........ 242........ 5 L 60 L E .......
TP2
Methylamine, 2.1 UN1061 ....... 2.1....... T50 306........... 304........ 314, 315... Forbidden 150 kg B 40
anhydrous.
Methylamine, aqueous 3 UN1235 II 3, 8...... B1, IB2, T7, TP1 150........... 202........ 243........ 1 L 5 L E 41
solution.
Methylamine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitramine and dry
salts thereof.
Methylamine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
nitroform.
Methylamine Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
perchlorate (dry).
Methylamyl acetate.. 3 UN1233 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
N-Methylaniline..... 6.1 UN2294 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
alpha-Methylbenzyl 6.1 UN2937 III 6.1....... IB3, T4, TP1 153........... 203........ 241........ 60 L 220 L A .......
alcohol.
3-Methylbutan-2-one. 3 UN2397 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
N-Methylbutylamine.. 3 UN2945 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 40
Methylchlorosilane.. 2.3 UN2534 ....... 2.3, 2.1, 2, A2, A3, A7, None.......... 226........ 314, 315... Forbidden Forbidden D 17, 40
8. B9, B14, N34
Methylcyclohexane... 3 UN2296 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methylcyclohexanols, 3 UN2617 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
flammable.
Methylcyclohexanone. 3 UN2297 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Methylcyclopentane.. 3 UN2298 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
D Methyldichloroarsine 6.1 NA1556 I 6.1....... 2, T20, TP4, None.......... 192........ None....... Forbidden Forbidden D 40
TP12, TP13,
TP38, TP45
Methyldichlorosilane 4.3 UN1242 I 4.3, 8, 3. A2, A3, A7, B6, None.......... 201........ 243........ Forbidden 1 L D 21, 28,
B77, N34, T10, 40, 49,
TP2, TP7, TP13 100
Methylene chloride, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Dichloromethane.
Methylene glycol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
dinitrate.
2-Methylfuran....... 3 UN2301 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
a-Methylglucoside Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
tetranitrate.
a-Methylglycerol Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
trinitrate.
5-Methylhexan-2-one. 3 UN2302 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
[[Page 203]]
Methylhydrazine..... 6.1 UN1244 I 6.1, 3, 8. 1, B7, B9, B14, None.......... 226........ 244........ Forbidden Forbidden D 21, 40,
B30, B72, B77, 49, 100
N34, T22, TP2,
TP13, TP38, TP44
4-Methylmorpholine 3 UN2535 II 3, 8...... B6, IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B 40
or n-
methylmorpholine.
Methylpentadienes... 3 UN2461 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L E .......
2-Methylpentan-2-ol. 3 UN2560 III 3......... B1, IB3, T2, TP1 150........... 203........ 242........ 60 L 220 L A .......
Methylpentanes, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hexanes.
Methylphenyldichloro 8 UN2437 II 8......... IB2, T7, TP2, 154........... 202........ 242........ 1 L 30 L C 40
silane. TP13
1-Methylpiperidine.. 3 UN2399 II 3, 8...... IB2, T7, TP1 None.......... 202........ 243........ 1 L 5 L B .......
Methyltetrahydrofura 3 UN2536 II 3......... IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
n.
Methyltrichlorosilan 3 UN1250 I 3, 8...... A7, B6, B77, None.......... 201........ 243........ Forbidden 2.5 L B 40
e. N34, T11, TP2,
TP13
alpha- 3 UN2367 II 3......... B1, IB2, T4, TP1 150........... 202........ 242........ 5 L 60 L B .......
Methylvaleraldehyde.
Mine rescue ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
equipment
containing carbon
dioxide, see Carbon
dioxide.
Mines with bursting 1.1F UN0136 II 1.1F...... ............. 62......... None....... Forbidden Forbidden 08 .......
charge.
Mines with bursting 1.1D UN0137 II 1.1D...... ............. 62......... None....... Forbidden Forbidden 03 .......
charge.
Mines with bursting 1.2D UN0138 II 1.2D...... ............. 62......... None....... Forbidden Forbidden 03 .......
charge.
Mines with bursting 1.2F UN0294 II 1.2F...... ............. 62......... None....... Forbidden Forbidden 08 .......
charge.
Mixed acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Nitrating acid,
mixtures etc.
Mobility aids, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Battery powered
equipment or
Battery powered
vehicle'.
D Model rocket motor.. 1.4C NA0276 II 1.4C...... 51 None.......... 62......... None....... Forbidden 75 kg 06 .......
D Model rocket motor.. 1.4S NA0323 II 1.4S...... 51 None.......... 62......... None....... 25 kg 100 kg 05 .......
Molybdenum 8 UN2508 III 8......... IB8, IP3, T4, 154........... 213........ 240........ 25 kg 100 kg C 40
pentachloride. TP1
Monochloroacetone Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
(unstabilized).
Monochloroethylene, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Vinyl chloride,
stabilized.
Monoethanolamine, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
see Ethanolamine,
solutions.
Monoethylamine, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Ethylamine.
Morpholine.......... 8 UN2054 I 8, 3...... T10, TP2 None.......... 201........ 243........ .5 L 2.5 L C 25,40
Morpholine, aqueous, ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
mixture, see
Corrosive liquids,
n.o.s..
Motor fuel anti- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
knock compounds see
Motor fuel anti-
knock mixtures.
+ Motor fuel anti- 6.1 UN1649 I 6.1, 3.... 14, B9, B90, None.......... 201........ 244........ Forbidden 30 L D 25, 40
knock mixtures. T14, TP2, TP13
Motor spirit, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Gasoline.
[[Page 204]]
Muriatic acid, see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Hydrochloric acid.
Musk xylene, see 5- ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
tert-Butyl-2,4,6-
trinitro-m-xylene.
Naphtha see ........... .................. .......... ............. .......... .......... ........... ........... ............ .......
Petroleum
distillates n.o.s..
Naphthalene, crude 4.1 UN1334 III 4.1....... A1, IB8, IP3 151........... 213........ 240........ 25 kg 100 kg A .......
or Naphthalene,
refined.
Naphthalene Forbidden .................. .......... ............. .......... .......... ........... ........... ............ .......
diozonide.
beta-Naphthylamine.. 6.1 UN1650 II 6.1....... IB8, IP2, IP4, None.......... 212........ 242........ 25 kg 100 kg A .......