Reference material.

§ 171.7 Reference material.

(a) Matter incorporated by reference—(1) General. There is incorporated, by reference in parts 170-189 of this subchapter, matter referred to that is not specifically set forth. This matter is hereby made a part of the regulations in parts 170-189 of this subchapter. The matter subject to change is incorporated only as it is in effect on the date of issuance of the regulation referring to that matter. The material listed in paragraph (a)(3) has been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is incorporated as it exists on the date of the approval and a notice of any change in the material will be published in the Federal Register. Matters referenced by footnote are included as part of the regulations of this subchapter.

(2) Accessibility of materials. All incorporated matter is available for inspection at:

(i) The Office of Hazardous Materials Safety, Office of Hazardous Materials Standards, Room 8422, NASSIF Building, 400 7th Street, SW., Washington, DC 20590; and

(ii) The Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

(3) Table of material incorporated by reference. The following table sets forth material incorporated by reference. The first column lists the name and address of the organization from which the material is available and the name of the material. The second column lists the section(s) of this subchapter, other than § 171.7, in which the matter is referenced. The second column is presented for information only and may not be all inclusive.

Source and name of material 49 CFR reference Air Transport Association of America, 1301 Pennsylvania Avenue, N.W., Washington, DC 20004-1707 ATA Specification No. 300 Packaging of Airline Supplies, Revision 19, July 31, 1996 172.102 The Aluminum Association, 420 Lexington Avenue, New York, NY 10017 Aluminum Standards and Data, Seventh Edition, June 1982 172.102; 178..46 and 178.65 American National Standards Institute, Inc., 25 West 43rd Street, New York, NY 10036 ANSI/ASHRAE 15-94, Safety Code for Mechanical Refrigeration 173.306 ANSI B16.5-77, Steel Pipe Flanges, Flanged Fittings 178.345; 178.360 ANSI N14.1 Uranium Hexafluoride—Packaging for Transport, 1971, 1982, 1987, 1990, 1995 and 2001 Editions. 173.417; 173.420 American Pyrotechnics Association (APA), P.O. Box 213, Chestertown, MD 21620 APA Standard 87-1, Standard for Construction and Approval for Transportation of Fireworks, Novelties, and Theatrical Pyrotechnics, January 23, 1998 version 173.56 American Society of Mechanical Engineers, ASME International, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900 ASME Code, Sections II (Parts A and B), V, VIII (Division 1), and IX of 1998 Edition of American Society of Mechanical Engineers Boiler and Pressure Vessel Code 173.32; 173.306; 173.315; 173.318; 173.420; 178.245; 178.255; 178.270; 178.271; 178.272; 178.337; 178.338; 178.345; 178.346; 178.347; 178.348; 179.400; 180.407; 180.417 ASME Code, Section V (FR Nondestructive Examination), 1977 180.407 ASME Code, Section IX (FR Welding and Brazing Qualification), 1977 and Addendum (1979) 178.245; 178.270; 178.337; 178.338 American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428 Noncurrent ASTM Standards are available from: Engineering Societies Library, 354 E. 47th Street, New York, NY 10017 ASTM A 20/A 20M-93a Standard Specification for General Requirements for Steel Plates for Pressure Vessels 178.337-2; 179.102-4; 179.102-17. ASTM A 47-68Malleable Iron Castings 179.200 ASTM A 240/A 240M-99b Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels 178.57; 178.358-5; 179.100-7; 179.100-10; 179.102-1; 179.102-4; 179.102-17; 179.200-7; 179.201-5; 179.220-7; 179.400-5. ASTM A 242-81Standard Specification for High-Strength Low-Alloy Structural Steel 179.100 ASTM A 262-93a Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels 179.100-7; 179.200-7; 179.201-4. ASTM A 300-58Steel Plates for Pressure Vessels for Service at Low Temperatures 178.337 ASTM A 302/A 302M-93 Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum Nickel 179.100-7; 179.200-7; 179.220-7. ASTM A 333-67Seamless and Welded Steel Pipe for Low-Temperature Service 178.45 ASTM A 366/A 366M-91 (1993)e1 Standard Specification for Steel, Sheet, Carbon, Cold-Rolled, Commercial Quality 178.601 ASTM A 370-94 Standard Test Methods and Definitions for Mechanical Testing of Steel Products 179.102-1; 179.102-4; 179.102-17. ASTM A 441-81Standard Specification for High-Strength Low-Alloy Structural Manganese Vanadium Steel 178.338 ASTM A 514-81Standard Specification for High-Yield Strength Quenched and Tempered Alloy Steel Plate, Suitable for Welding 178.338 ASTM A 516/A 516M-90 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower- Temperature Service 178.337-2; 179.100-7; 179.100-20; 179.102-1; 179.102-2; 179.102-4; 179.102-17; 179.200-7; 179.220-7. ASTM A 537/A 537M-91 Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel 179.100-7; 179.102-4; 179.102-17. ASTM A 568/A 568M-95 Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for 178.601 ASTM A 572-82Standard Specification for High-Strength Low-Alloy Columbian-Vanadium Steels of Structural Quality 178.338; 179.100 ASTM A 588-81Standard Specification for High-Strength Low-Alloy Structural Steel with 50 Ksi Minimum Yield Point to 4 in. Thick 179.100; 178.338 ASTM A 606-75Standard Specification for Steel Sheet and Strip Hot-Rolled and Cold-Rolled, High-Strength, Low-Alloy, with Improved Atmospheric Corrosion Resistance, 1975 (Reapproved 1981) 178.338 ASTM A 612-72aHigh Strength Steel Plates for Pressure Vessels for Moderate and Lower Temperature Service 178.337 ASTM A 633-79aStandard Specification for Normalized High-Strength Low-Alloy Structural Steel, 1979 Edition 178.338 ASTM A 715-81Standard Specification for Steel Sheet and Strip, Hot-Rolled, High-Strength, Low-Alloy with Improved Formability, 1981 178.338 ASTM B 162-93a Standard Specification for Nickel Plate, Sheet, and Strip 179.200-7. ASTM B 209-93 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate 179.100-7; 179.200-7; 179.220-7. ASTM B 557-84 Tension Testing Wrought and Cast Aluminum and Magnesium-Alloy Products 178.46. ASTM B 580-79 Standard Specification for Anodic Oxide Coatings on Aluminum, (Re-approved 2000) 173.316; 173.318; 178.338-17 ASTM D 56-97aStandard Test Method for Flash Point by Tag Closed Tester 173.120 ASTM D 93-97Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 173.120 ASTM D 445-88Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) 171.8 ASTM D 1200-88Viscosity by Ford Viscosity Cup 171.8 ASTM D 1835-97Standard Specification for Liquefied Petroleum (LP) Gases 180.209 ASTM D 1838-64Copper Strip Corrosion by Liquefied Petroleum (LP) Gases 173.315 ASTM D 3278-96Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus 173.120 ASTM D 3828-97, Standard Test Methods for Flash Point by Small Scale Closed Tester 173.120. ASTM D 4206-96 Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus 173.120. ASTM D 4359-90Standard Test Method for Determining Whether a Material is a Liquid or a Solid 171.8 ASTM E 8-99Standard Test Methods for Tension Testing of Metallic Materials 178.36; 178.37; 178.38; 178.39; 178.44; 178.45; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.68. ASTM E 23-98Standard Test Methods for Notched Bar Impact Testing of Metallic Materials 178.57 ASTM E 112-88 Standard Test Methods for Determining Average Grain Size 178.44. ASTM E 112-96Standard Test Methods for Determining Average Grain Size, 1996 Edition 178.274 ASTM E 213-98Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing 178.45 ASTM E 290-92Standard Test Method for Semi-Guided Bend Test for Ductility of Metallic Materials 178.46. ASTM E 681-85Standard Test Method for Concentration Limits of Flammability of Chemicals 173.115 ASTM G 23-69Standard Recommended Practice for Operating Light-and-Water Exposure Apparatus (Carbon-Arc Type) for Exposure of Nonmetallic Materials 172.407; 172.519 ASTM G 26-70Standard Recommended Practice for Operating Light-and-Water Exposure Apparatus (Xenon-Arc-Type) for Exposure of Nonmetallic Materials 172.407; 172.519 ASTM G 31-72 (Reapproved 1995) Standard Practice for Laboratory Immersion Corrosion Testing of Metals 173.137 American Water Works Association, 1010 Vermont Avenue, NW., Suite 810, Washington, DC 20005 AWWA Standard C207-55, Steel Pipe Flanges, 1955 178.360 American Welding Society, 550 N. W. Le Jeune Road, Miami, Florida 33126 AWS Code B 3.0; Standard Qualification Procedure; 1972 (FRB 3.0-41, rev. May 1973) 178.356 AWS Code D 1.0; Code for Welding in Building Construction (FR D 1.0-66) 178.356 Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 AAR Manual of Standards and Recommended Practices, Section C—Part III, Specifications for Tank Cars, Specification M-1002, September 1992 173.31. AAR Manual of Standards and Recommended Practices, Section C—Part III, Specifications for Tank Cars, Specification M-1002, January 1996 174.63; 179.6; 179.7; 179.12; 179.15; 179.16; 179.20; 179.22; 179.100; 179.101; 179.102; 179.103; 179.200; 179.201; 179.220; 179.300; 179.400; 180.509; 180.513; 180.515; 180.517. AAR Manual of Standards and Recommended Practices, Section I, Specially Equipped Freight Car and Intermodal Equipment, 1988 174.55; 174.63. AAR Specifications for Design, Fabrication and Construction of Freight Cars, Volume 1, 1988 179.16. Chlorine Institute, Inc., 2001 L Street, NW., Suite 506, Washington, DC 20036 Type 11/2 JQ 225, Dwg, H51970, Revision D, April 5, 1989; or Type 11/2 JQ 225, Dwg. H50155, Revision F, April 4, 1989 173.315 Section 3, Pamphlet 57, Emergency Shut-Off Systems for Bulk Transfer of Chlorine, 3rd Edition, October 1997 177.840 Standard Chlorine Angle Valve Assembly, Dwg. 104-8, July 1993 178.337-9 Excess Flow Valve with Removable Seat, Dwg. 101-7, July 1993 178.337-8 Excess Flow Valve with Removable Basket, Dwg. 106-6, July 1993 178.337-8 Standards for Housing and Manway Covers for Steel Cargo Tanks, Dwg. 137-3, September 1, 1982 178.337-10 Compressed Gas Association, Inc., 4221 Walney Road, 5th Floor, Chantilly, Virginia 20151 CGA Pamphlet C-3, Standards for Welding on Thin-Walled Steel Cylinders, 1994 178.47; 178.50; 178.51; 178.53; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.65; 178.68; 180.211. CGA Pamphlet C-5, Cylinder Service Life—Seamless Steel High Pressure Cylinders, 1991 173.302a CGA Pamphlet C-6, Standards for Visual Inspection of Steel Compressed Gas Cylinders, 1993 173.198; 180.205; 180.209; 180.211; 180.519. CGA Pamphlet C-6.1, Standards for Visual Inspection of High Pressure Aluminum Compressed Gas Cylinders, 1995 180.205; 180.209 CGA Pamphlet C-6.2, Guidelines for Visual Inspection and Requalification of Fiber Reinforced High Pressure Cylinders, 1988 180.205 CGA Pamphlet C-6.3, Guidelines for Visual Inspection and Requalification of Low Pressure Aluminum Compressed Gas Cylinders, 1991 180.205; 180.209 CGA Pamphlet C-7, A Guide for the Preparation of Precautionary Markings for Compressed Gas Containers, appendix A, issued 1992 (6th Edition) 172.400a CGA Pamphlet C-8, Standard for Requalification of DOT-3HT Cylinder Design, 1985 180.205 CGA Pamphlet C-11, Recommended Practices for Inspection of Compressed Gas Cylinders at Time of Manufacture, 1993 178.35. CGA Pamphlet C-12, Qualification Procedure for Acetylene Cylinder Design, 1994 173.301; 173.303; 178.59; 178.60. CGA Pamphlet C-13, Guidelines for Periodic Visual Inspection and Requalification of Acetylene Cylinders, 1992 173.303; 180.205; 180.209. CGA Pamphlet C-14, Procedures for Fire Testing of DOT Cylinder Pressure Relief Device Systems, 1979 173.301 CGA Pamphlet G-2.2 Tentative Standard Method for Determining Minimum of 0.2% Water in Anhydrous Ammonia, 1985 173.315 CGA Pamphlet G-4.1, Cleaning Equipment for Oxygen Service, 1985 178.338 CGA Pamphlet P-20, Standard for the Classification of Toxic Gas Mixtures, 1995 173.115 CGA Pamphlet S-1.1., Pressure Relief Device Standards—Part 1—Cylinders for Compressed Gases, 1994 (with the exception of paragraph 9.1.1.1) 173.301; 173.304a. CGA Pamphlet S-1.2, Safety Relief Device Standards Part 2—Cargo and Portable Tanks for Compressed Gases, 1980 173.315; 173.318 CGA Pamphlet S-7, Method for Selecting Pressure Relief Devices for Compressed Gas Mixtures in Cylinders, 1996 173.301 CGA Technical Bulletin TB-2, Guidelines for Inspection and Repair of MC-330 and MC-331 Cargo Tanks, 1980 180.413 Department of Defense (DOD), 2461 Eisenhower Avenue, Alexandria, VA 22331 DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1-47; DLAR 8220.1: Explosives Hazard Classification Procedures, January 1998 173.56 Department of Energy (USDOE), 100 Independence Avenue SW., Washington, DC 20545 USDOE publications available from: Superintendent of Documents, Government Printing Office (GPO) or The National Technical Information Service (NTIS) USDOE, CAPE-1662, Revision 1, and Supplement 1, Civilian Application Program Engineering Drawings 178.356; 178.358 USDOE, Material and Equipment Specification No. SP-9, Rev. 1, and Supplement—Fire Resistant Phenolic Foam 178.356; 178.358 USDOE, ORO 651—Uranium Hexafloride; A Manual of Good Practices, Revision 6, 1991 edition 173.417 USDOE, KSS-471, November 30, 1986—Proposal for Modifications to U.S. Department of Transportation Specification 21PF-1, Fire and Shock Resistant Phenolic Foam—Insulated Metal Overpack 178.358 General Services Administration, Specification Office, Rm. 6662, 7th and D Street, SW., Washington, DC 20407 Federal Specification RR-C-901C, Cylinders, Compressed Gas: High Pressure Steel DOT 3AA, and Aluminum Applications, January 15, 1981 (Superseding RR-C-901B, August 1, 1967) 173.302; 173.336; 173.337 Health and Human Services Centers for Disease Control and Prevention, 1600 Clifton Road N.E., Atlanta GA 30333 Also available from: Superintendent of Documents, Government Printing Office (GPO), HHS Publication No. (CDC) 93-8395, Biosafety in Microbiological and Biomedical Laboratories, 3rd Edition, May 1993, Section II 173.134 Institute of Makers of Explosives, 1120 19th Street, Suite 310, Washington, DC 20036-3605 IME Safety Library Publication No. 22 (IME Standard 22), Recommendation for the Safe Transportation of Detonators in a Vehicle with Certain Other Explosive Materials, May 1993 173.63, 177.835 International Atomic Energy Agency (IAEA), P.O. Box 100, Wagramer Strasse 5, A-1400 Vienna, Austria Also available from: Bernan Associates, 4611-F Assembly Drive, Lanham, MD 20706-4391, USA; or Renouf Publishing Company, Ltd., 812 Proctor Avenue, Ogdensburg, New York 13669, USA IAEA, Regulations for the Safe Transport of Radioactive Material, No. TS-R-1, 1996 Edition (Revised), (ST-1, Revised) 171.12 IAEA, Regulations for the Safe Transport of Radioactive Material, Safety Series No. 6, 1985 Edition (as Amended 1990) 171.12; 173.415; 173.416; 173.417; 173.473 International Civil Aviation Organization (ICAO), P.O. Box 400, Place de l'Aviation Internationale, 1000 Sherbrooke Street West, Montreal, Quebec, Canada H3A 2R2 ICAO Technical Instructions available from: INTEREG, International Regulations, Publishing and Distribution Organization, P.O. Box 60105, Chicago, IL 60660 Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO Technical Instructions), DOC 9284-AN/905, 2001-2002 Edition 171.11; 172.202; 172.401; 172.512; 172.602 International Maritime Organization (IMO), 4 Albert Embankment, London, SE17SR, United Kingdom or New York Nautical Instrument & Service Corporation, 140 W. Broadway, New York, NY 10013 International Maritime Dangerous Goods (IMDG) Code, 1994 Consolidated Edition, as amended by Amendment 29 (1998) (English edition) 171.12; 172.401; 172.407; 173.21, 176.2; 176.5; 176.11; 176.27; 176.30; 176.720 International Maritime Dangerous Goods (IMDG) Code, 2000 edition, including Amendment 30-00 (English edition) 171.12; 172.401; 172.502; 173.21; 176.2; 176.5; 176.11; 176.27; 176.30. International Organization for Standardization, Case Postale 56, CH-1211, Geneve 20, Switzerland Also available from: ANSI 25 West 43rd Street, New York, NY 10036 ISO-82-1974(E)Steels Tensile Testing 178.270-3 ISO 535-1991(E)Paper and board—Determination of water absorptiveness—Cobb method 178.516 ISO 1496-3Series 1 freight containers—Specification and testing, Part 3: Tank containers for liquids, gases and pressurized dry bulk, March 1, 1995, Fourth Edition 178.274 ISO 1496-3-1995(E) - Series 1 Freight Containers—Specification and Testing—Part 3: Tank Containers for Liquids, Gases and Pressurized Dry Bulk 173.411 ISO-2431-1984(E)Standard Cup Method 173.121 ISO 2592-1973(E) Petroleum products—Determination of flash and fire points—Cleveland open cup method 173.120 ISO 2919-1980(E) - Sealed radioactive sources—Classification 173.469 ISO 3036-1975(E) Board—Determination of puncture resistance 178.708 ISO 3574-1986(E) Cold-reduced carbon steel sheet of commercial and drawing qualities 178.503 ISO 4126-1Safety valves—Part 1: General Requirements, December 15, 1991, First Edition 178.274 ISO/TR 4826-1979(E) - Sealed radioactive sources—Leak test methods 173.469 ISO 6892Metallic materials—Tensile testing, July 15, 1984, First Edition 178.274 ISO 8115 Cotton bales—Dimensions and density, 1986 Edition 172.102 ISO 9328-1—1991(E) Steel plates and strips for pressure purposes—Technical delivery conditions—Part 1: General requirements 173.137 National Board of Boiler and Pressure Vessel Inspectors, 1055 Crupper Avenue, Columbus, Ohio 43229 National Board Inspection Code, A Manual for Boiler and Pressure Vessel Inspectors, NB-23, 1992 Edition 180.413 National Fire Protection Association, Batterymarch Park, Quincy, MA 02269 NFPA Pamphlet No. 58—Standard for the Storage and Handling of Liquefied Petroleum Gases, 1979 173.315 National Institute of Standards and Technology, Department of Commerce, 5285 Port Royal Road, Springfield, VA 22151 USDC, NBS Handbook H-28 (1957), 1957 Handbook of Screw-Thread Standards for Federal Services, Part II, December 1966 Edition 178.45, 178.46 National Motor Freight Traffic Association, Inc., Agent 1616 P Street, NW., Washington, DC 20036 National Motor Freight Classification NMF 100-I, 1982 177.841 Organization for Economic Cooperation and Development (OECD) OECD Publications and Information Center, 2001 L Street, Suite 700, Washington, DC 20036 OECD Guideline for Testing of Chemicals, No.404 “Acute Dermal Irritation/Corrosion”, 1992 173.137 Transport Canada, TDG Canadian Government Publishing Center, Supply and Services, Canada, Ottawa, Ontario, Canada K1A 059 Transportation of Dangerous Goods Regulations, 1 July 1985, SOR/85/77, incorporating the following Registration Numbers: SOR/85-314, SOR/85-585, SOR/85-609, SOR/86-526, SOR/88-635, SOR/87-335, SOR/87-186, SOR/89-39, SOR/89-294, SOR/90-847, SOR/91-711, SOR/91-712, SOR/92-447, SOR/92-600, SOR/93-203, SOR/93-274, SOR/93-525, SOR/94-146 and SOR/94-264 (English edition), SOR/95-241, and SOR/95-547 171.12a; 172.401; 172.502. Truck Trailer Manufacturers Association, 1020 Princess Street, Alexandria, Virginia 22314 TTMA RP No. 81, Performance of Spring Loaded Pressure Relief Valves on MC 306, MC 307, and MC 312 Tanks, May 24, 1989 Edition 178.345-10 TTMA RP No. 61-94, Performance of Manhole and/or Fill Opening Assemblies on MC 306 and DOT 406 Cargo Tanks, December 28, 1994 Edition. 180.405 TTMA TB No. 107, Procedure for Testing Inservice, Unmarked, and/or Uncertified MC 306 Type Cargo Tank Manhole Covers, May 24, 1989 Edition 180.405 United Nations, United Nations Sales Section, New York, NY 10017 UN Recommendations on the Transport of Dangerous Goods, Eleventh Revised Edition (1999) 172.401; 172.407; 172.502; 173.24. UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, Third Revised Edition (1999) 172.102; 173.21; 173.56; 173.57; 173.124; 173.128; 173.166; 173.185.

(b) List of informational materials not requiring incorporation by reference. The materials listed in this paragraph do not require approval for incorporation by reference and are included for informational purposes. These materials may be used as noted in those sections in which the material is referenced.

Source and name of material 49 CFR reference Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 AAR Catalog Nos. SE60CHT; SE60CC; SE60CHTE; SE60CE; SE60DC; SE60DE 179.14 AAR Catalog Nos. SE67CC; SE67CE; SE67BHT; SE67BC; SE67BHTE; SE67BE 179.14 AAR Catalog Nos. SE68BHT; SE68BC; SE68BHTE; SE68BE 179.14 AAR Catalog Nos. SE69AHTE; SE69AE 179.14 AAR Catalog Nos. SF70CHT; SF70CC; SF70CHTE; SF70CE 179.14 AAR Catalog Nos. SF73AC; SF73AE; SF73AHT; SF73AHTE 179.14 AAR Catalog Nos. SF79CHT; SF79CC; SF79CHTE; SF79CE 179.14 Bureau of Explosives, Hazardous Materials Systems (BOE), Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 Fetterley's Formula (The Determination of the Relief Dimensions for Safety Valves on Containers in which Liquefied gas is charged and when the exterior surface of the container is exposed to a temperature of 1,200 °F.) 173.315 Pamphlet 6, Illustrating Methods for Loading and Bracing Carload and Less-Than-Carload Shipments of Explosives and Other Dangerous Articles, 1962 174.55; 174.101; 174.112; 174.115; 174.290 Pamphlet 6A (includes appendix No. 1, October 1944 and appendix 2, December 1945), Illustrating Methods for Loading and Bracing Carload and Less-Than-Carload Shipments of Loaded Projectiles, Loaded Bombs, etc., 1943 174.101; 174.290 Pamphlet 6C, Illustrating Methods for Loading and Bracing Trailers and Less-Than-Trailer Shipments of Explosives and Other Dangerous Articles Via Trailer-on-Flatcar (TOFC) or Container-on-Flatcar (COFC), 1985 174.55; 174.63; 174.101; 174.112; 174.115 Emergency Handling of Hazardous Materials in Surface Transportation, 1989 171.7 National Association of Corrosion Engineers, 1440 South Creek, Houston, Texas 77084 NACE Standard TM-01-69, Test Method Laboratory Corrosion Testing of Metals for the Process Industries, 1969 173.136 Society of Plastics Industries, Inc., Organic Peroxide Producers Safety Division, 1275 K Street, NW., Suite 400, Washington, DC 20005 Self Accelerating Decomposition Temperature Test, 1972 173.21 [Amdt. 171-111, 55 FR 52466, Dec. 21, 1990] Editorial Note:

For Federal Register citations affecting § 171.7, see the List of CFR Sections Affected which appears in the Finding Aids section of the printed volume and on GPO Access.

Effective Date Note:

At 67 FR 53132, Aug. 14, 2002, § 171.7 was amended in the table in paragraph (a)(3) by adding two new entries in alphanumeric sequence under the American Society for Testing and Materials and in the table in paragraph (b) by adding three new entries in alphabetical order, effective Oct. 1, 2002. At 67 FR 54967, Aug. 27, 2002, the effective date was corrected to Feb. 14, 2003. For the convenience of the user, the added text is set forth as follows:

§ 171.7— Reference material.

(a) * * *

(3) Table of material incorporated by reference.

Source and name of material 49 CFR reference ******* American Society for Testing and Materials * * * ******* ASTM D 1709-01 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method 173.197 ******* ASTM D 1922-00a Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method 173.197 *******

(b) List of informational materials not requiring incorporation by reference. * * *

Source and name of material 49 CFR reference American Biological Safety Association 1202 Allanson Road, Mundelein, IL 60060 Risk Group Classification for Infectious Agents, 1998 173.134 ******* Centers for Disease Control and Prevention 1600 Clifton Road, Atlanta, GA 30333 Biosafety in Microbiological and Biomedical Laboratories, Fourth Edition, April 1999 173.134 ******* National Institutes of Health Bethesda, MD 20892 NIH Guidelines for Research Involving Recombinant DNA Molecules (NIH Guidelines), January 2001, Appendix B 173.134 *******