[Title 49 CFR ]
[Code of Federal Regulations (annual edition) - October 1, 2011 Edition]
[From the U.S. Government Printing Office]



[[Page i]]

          

          Title 49

Transportation


________________________

Parts 100 to 177

                         Revised as of October 1, 2011

          Containing a codification of documents of general 
          applicability and future effect

          As of October 1, 2011
                    Published by the Office of the Federal Register 
                    National Archives and Records Administration as a 
                    Special Edition of the Federal Register

[[Page ii]]

          U.S. GOVERNMENT OFFICIAL EDITION NOTICE

          Legal Status and Use of Seals and Logos
          
          
          The seal of the National Archives and Records Administration 
              (NARA) authenticates the Code of Federal Regulations (CFR) as 
              the official codification of Federal regulations established 
              under the Federal Register Act. Under the provisions of 44 
              U.S.C. 1507, the contents of the CFR, a special edition of the 
              Federal Register, shall be judicially noticed. The CFR is 
              prima facie evidence of the original documents published in 
              the Federal Register (44 U.S.C. 1510).

          It is prohibited to use NARA's official seal and the stylized Code 
              of Federal Regulations logo on any republication of this 
              material without the express, written permission of the 
              Archivist of the United States or the Archivist's designee. 
              Any person using NARA's official seals and logos in a manner 
              inconsistent with the provisions of 36 CFR part 1200 is 
              subject to the penalties specified in 18 U.S.C. 506, 701, and 
              1017.

          Use of ISBN Prefix

          This is the Official U.S. Government edition of this publication 
              and is herein identified to certify its authenticity. Use of 
              the 0-16 ISBN prefix is for U.S. Government Printing Office 
              Official Editions only. The Superintendent of Documents of the 
              U.S. Government Printing Office requests that any reprinted 
              edition clearly be labeled as a copy of the authentic work 
              with a new ISBN.

              
              
          U . S . G O V E R N M E N T P R I N T I N G O F F I C E

          ------------------------------------------------------------------

          U.S. Superintendent of Documents  Washington, DC 
              20402-0001

          http://bookstore.gpo.gov

          Phone: toll-free (866) 512-1800; DC area (202) 512-1800

[[Page iii]]




                            Table of Contents



                                                                    Page
  Explanation.................................................       v

  Title 49:
    SUBTITLE B--Other Regulations Relating to Transportation
          Chapter I--Pipeline and Hazardous Materials Safety 
          Administration, Department of Transportation               5
  Finding Aids:
      Table of CFR Titles and Chapters........................     859
      Alphabetical List of Agencies Appearing in the CFR......     879
      List of CFR Sections Affected...........................     889

[[Page iv]]





                     ----------------------------

                     Cite this Code: CFR
                     To cite the regulations in 
                       this volume use title, 
                       part and section number. 
                       Thus, 49 CFR 105.5 refers 
                       to title 49, part 105, 
                       section 5.

                     ----------------------------

[[Page v]]



                               EXPLANATION

    The Code of Federal Regulations is a codification of the general and 
permanent rules published in the Federal Register by the Executive 
departments and agencies of the Federal Government. The Code is divided 
into 50 titles which represent broad areas subject to Federal 
regulation. Each title is divided into chapters which usually bear the 
name of the issuing agency. Each chapter is further subdivided into 
parts covering specific regulatory areas.
    Each volume of the Code is revised at least once each calendar year 
and issued on a quarterly basis approximately as follows:

Title 1 through Title 16.................................as of January 1
Title 17 through Title 27..................................as of April 1
Title 28 through Title 41...................................as of July 1
Title 42 through Title 50................................as of October 1

    The appropriate revision date is printed on the cover of each 
volume.

LEGAL STATUS

    The contents of the Federal Register are required to be judicially 
noticed (44 U.S.C. 1507). The Code of Federal Regulations is prima facie 
evidence of the text of the original documents (44 U.S.C. 1510).

HOW TO USE THE CODE OF FEDERAL REGULATIONS

    The Code of Federal Regulations is kept up to date by the individual 
issues of the Federal Register. These two publications must be used 
together to determine the latest version of any given rule.
    To determine whether a Code volume has been amended since its 
revision date (in this case, October 1, 2011), consult the ``List of CFR 
Sections Affected (LSA),'' which is issued monthly, and the ``Cumulative 
List of Parts Affected,'' which appears in the Reader Aids section of 
the daily Federal Register. These two lists will identify the Federal 
Register page number of the latest amendment of any given rule.

EFFECTIVE AND EXPIRATION DATES

    Each volume of the Code contains amendments published in the Federal 
Register since the last revision of that volume of the Code. Source 
citations for the regulations are referred to by volume number and page 
number of the Federal Register and date of publication. Publication 
dates and effective dates are usually not the same and care must be 
exercised by the user in determining the actual effective date. In 
instances where the effective date is beyond the cut-off date for the 
Code a note has been inserted to reflect the future effective date. In 
those instances where a regulation published in the Federal Register 
states a date certain for expiration, an appropriate note will be 
inserted following the text.

OMB CONTROL NUMBERS

    The Paperwork Reduction Act of 1980 (Pub. L. 96-511) requires 
Federal agencies to display an OMB control number with their information 
collection request.

[[Page vi]]

Many agencies have begun publishing numerous OMB control numbers as 
amendments to existing regulations in the CFR. These OMB numbers are 
placed as close as possible to the applicable recordkeeping or reporting 
requirements.

OBSOLETE PROVISIONS

    Provisions that become obsolete before the revision date stated on 
the cover of each volume are not carried. Code users may find the text 
of provisions in effect on a given date in the past by using the 
appropriate numerical list of sections affected. For the period before 
April 1, 2001, consult either the List of CFR Sections Affected, 1949-
1963, 1964-1972, 1973-1985, or 1986-2000, published in eleven separate 
volumes. For the period beginning April 1, 2001, a ``List of CFR 
Sections Affected'' is published at the end of each CFR volume.

``[RESERVED]'' TERMINOLOGY

    The term ``[Reserved]'' is used as a place holder within the Code of 
Federal Regulations. An agency may add regulatory information at a 
``[Reserved]'' location at any time. Occasionally ``[Reserved]'' is used 
editorially to indicate that a portion of the CFR was left vacant and 
not accidentally dropped due to a printing or computer error.

INCORPORATION BY REFERENCE

    What is incorporation by reference? Incorporation by reference was 
established by statute and allows Federal agencies to meet the 
requirement to publish regulations in the Federal Register by referring 
to materials already published elsewhere. For an incorporation to be 
valid, the Director of the Federal Register must approve it. The legal 
effect of incorporation by reference is that the material is treated as 
if it were published in full in the Federal Register (5 U.S.C. 552(a)). 
This material, like any other properly issued regulation, has the force 
of law.
    What is a proper incorporation by reference? The Director of the 
Federal Register will approve an incorporation by reference only when 
the requirements of 1 CFR part 51 are met. Some of the elements on which 
approval is based are:
    (a) The incorporation will substantially reduce the volume of 
material published in the Federal Register.
    (b) The matter incorporated is in fact available to the extent 
necessary to afford fairness and uniformity in the administrative 
process.
    (c) The incorporating document is drafted and submitted for 
publication in accordance with 1 CFR part 51.
    What if the material incorporated by reference cannot be found? If 
you have any problem locating or obtaining a copy of material listed as 
an approved incorporation by reference, please contact the agency that 
issued the regulation containing that incorporation. If, after 
contacting the agency, you find the material is not available, please 
notify the Director of the Federal Register, National Archives and 
Records Administration, 8601 Adelphi Road, College Park, MD 20740-6001, 
or call 202-741-6010.

CFR INDEXES AND TABULAR GUIDES

    A subject index to the Code of Federal Regulations is contained in a 
separate volume, revised annually as of January 1, entitled CFR Index 
and Finding Aids. This volume contains the Parallel Table of Authorities 
and Rules. A list of CFR titles, chapters, subchapters, and parts and an 
alphabetical list of agencies publishing in the CFR are also included in 
this volume.
    An index to the text of ``Title 3--The President'' is carried within 
that volume.

[[Page vii]]

    The Federal Register Index is issued monthly in cumulative form. 
This index is based on a consolidation of the ``Contents'' entries in 
the daily Federal Register.
    A List of CFR Sections Affected (LSA) is published monthly, keyed to 
the revision dates of the 50 CFR titles.

REPUBLICATION OF MATERIAL

    There are no restrictions on the republication of material appearing 
in the Code of Federal Regulations.

INQUIRIES

    For a legal interpretation or explanation of any regulation in this 
volume, contact the issuing agency. The issuing agency's name appears at 
the top of odd-numbered pages.
    For inquiries concerning CFR reference assistance, call 202-741-6000 
or write to the Director, Office of the Federal Register, National 
Archives and Records Administration, 8601 Adelphi Road, College Park, MD 
20740-6001 or e-mail fedreg.info@nara.gov.

SALES

    The Government Printing Office (GPO) processes all sales and 
distribution of the CFR. For payment by credit card, call toll-free, 
866-512-1800, or DC area, 202-512-1800, M-F 8 a.m. to 4 p.m. e.s.t. or 
fax your order to 202-512-2104, 24 hours a day. For payment by check, 
write to: US Government Printing Office - New Orders, P.O. Box 979050, 
St. Louis, MO 63197-9000.

ELECTRONIC SERVICES

    The full text of the Code of Federal Regulations, the LSA (List of 
CFR Sections Affected), The United States Government Manual, the Federal 
Register, Public Laws, Public Papers of the Presidents of the United 
States, Compilation of Presidential Documents and the Privacy Act 
Compilation are available in electronic format via www.ofr.gov. For more 
information, contact the GPO Customer Contact Center, U.S. Government 
Printing Office. Phone 202-512-1800, or 866-512-1800 (toll-free). E-
mail, gpo@custhelp.com.
    The Office of the Federal Register also offers a free service on the 
National Archives and Records Administration's (NARA) World Wide Web 
site for public law numbers, Federal Register finding aids, and related 
information. Connect to NARA's web site at www.archives.gov/federal-
register.

    Raymond A. Mosley,
    Director,
    Office of the Federal Register.
    October 1, 2011.







[[Page ix]]



                               THIS TITLE

    Title 49--Transportation is composed of nine volumes. The parts in 
these volumes are arranged in the following order: Parts 1-99, parts 
100-177, parts 178-199, parts 200-299, parts 300-399, parts 400-571, 
parts 572-999, parts 1000-1199, and part 1200 to end. The first volume 
(parts 1-99) contains current regulations issued under subtitle A--
Office of the Secretary of Transportation; the second volume (parts 100-
177) and the third volume (parts 178-199) contain the current 
regulations issued under chapter I--Pipeline and Hazardous Materials 
Safety Administration (DOT); the fourth volume (parts 200-299) contains 
the current regulations issued under chapter II--Federal Railroad 
Administration (DOT); the fifth volume (parts 300-399) contains the 
current regulations issued under chapter III--Federal Motor Carrier 
Safety Administration (DOT); the sixth volume (parts 400-571) contains 
the current regulations issued under chapter IV--Coast Guard (DHS), and 
some of chapter V--National Highway Traffic Safety Administration (DOT); 
the seventh volume (parts 572-999) contains the rest of the regulations 
issued under chapter IV, and the current regulations issued under 
chapter VI--Federal Transit Administration (DOT), chapter VII--National 
Railroad Passenger Corporation (AMTRAK), and chapter VIII--National 
Transportation Safety Board; the eighth volume (parts 1000-1199) 
contains the current regulations issued under chapter X--Surface 
Transportation Board and the ninth volume (part 1200 to end) contains 
the current regulations issued under chapter X--Surface Transportation 
Board, chapter XI--Research and Innovative Technology Administration, 
and chapter XII--Transportation Security Administration, Department of 
Transportation. The contents of these volumes represent all current 
regulations codified under this title of the CFR as of October 1, 2011.

    In the volume containing parts 100-177, see Sec.  172.101 for the 
Hazardous Materials Table. The Federal Motor Vehicle Safety Standards 
appear in part 571.

    Redesignation tables for chapter III--Federal Motor Carrier Safety 
Administration, Department of Transportation and chapter XII--
Transportation Security Administration, Department of Transportation 
appear in the Finding Aids section of the fifth and ninth volumes.

    For this volume, Jonn V. Lilyea was Chief Editor. The Code of 
Federal Regulations publication program is under the direction of 
Michael L. White, assisted by Ann Worley.


[[Page 1]]



                        TITLE 49--TRANSPORTATION




                  (This book contains parts 100 to 185)

  --------------------------------------------------------------------

        SUBTITLE B--Other Regulations Relating To Transportation

                                                                    Part

chapter i--Pipeline and Hazardous Materials Safety 
  Administration, Department of Transportation..............         105

[[Page 3]]

        Subtitle B--Other Regulations Relating to Transportation

[[Page 5]]



   CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, 

                      DEPARTMENT OF TRANSPORTATION




  --------------------------------------------------------------------

        SUBCHAPTER A--HAZARDOUS MATERIALS AND OIL TRANSPORTATION
Part                                                                Page
105             Hazardous Materials Program definitions and 
                    general procedures......................           7
106             Rulemaking procedures.......................          13
107             Hazardous materials program procedures......          19
109             Department of Transportation hazardous 
                    materials procedural regulations for 
                    opening of packages, emergency orders, 
                    and emergency recalls...................          66
110             Hazardous materials public sector training 
                    and planning grants.....................          72
                    SUBCHAPTER B--OIL TRANSPORTATION
130             Oil spill prevention and response plans.....          81
              SUBCHAPTER C--HAZARDOUS MATERIALS REGULATIONS
171             General information, regulations, and 
                    definitions.............................          84
172             Hazardous materials table, special 
                    provisions, hazardous materials 
                    communications, emergency response 
                    information, training requirements, and 
                    security plans..........................         130
173             Shippers--general requirements for shipments 
                    and packagings..........................         432
174             Carriage by rail............................         729
175             Carriage by aircraft........................         754
176             Carriage by vessel..........................         775
177             Carriage by public highway..................         835

[[Page 7]]



         SUBCHAPTER A_HAZARDOUS MATERIALS AND OIL TRANSPORTATION



PART 105_HAZARDOUS MATERIALS PROGRAM DEFINITIONS AND GENERAL PROCEDURES--Table 

of Contents



                          Subpart A_Definitions

Sec.
105.5 Definitions.

                      Subpart B_General Procedures

105.15 Defined terms used in this subpart.

                Obtaining Guidance and Public Information

105.20 Guidance and interpretations.
105.25 Reviewing public documents.
105.26 Obtaining records on file with PHMSA.
105.30 Information made available to the public and request for 
          confidential treatment.

                            Serving Documents

105.35 Serving documents in PHMSA proceedings.
105.40 Designated agents for non-residents.

                                Subpoenas

105.45 Issuing a subpoena.
105.50 Serving a subpoena.
105.55 Refusal to obey a subpoena.

    Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.

    Source: 67 FR 42951, June 25, 2002, unless otherwise noted.

    Editorial Note: Nomenclature changes to part 105 appear at 70 FR 
56087, Sept. 23, 2005.



                          Subpart A_Definitions



Sec. 105.5  Definitions.

    (a) This part contains the definitions for certain words and phrases 
used throughout this subchapter (49 CFR parts 105 through 110). At the 
beginning of each subpart, the Pipeline and Hazardous Materials Safety 
Administration (``PHMSA'' or ``we'') will identify the defined terms 
that are used within the subpart--by listing them--and refer the reader 
to the definitions in this part. This way, readers will know that PHMSA 
has given a term a precise meaning and will know where to look for it.
    (b) Terms used in this part are defined as follows:
    Associate Administrator means Associate Administrator for Hazardous 
Materials Safety, Pipeline and Hazardous Materials Safety 
Administration.
    Approval means written consent, including a competent authority 
approval, from the Associate Administrator or other designated 
Department official, to perform a function that requires prior consent 
under subchapter C of this chapter (49 CFR parts 171 through 180).
    Competent Authority means a national agency that is responsible, 
under its national law, for the control or regulation of some aspect of 
hazardous materials (dangerous goods) transportation. Another term for 
Competent Authority is ``Appropriate authority'' which is used in the 
International Civil Aviation Organization's (ICAO) Technical 
Instructions for the Safe Transport of Dangerous Goods by Air. The 
Associate Administrator is the United States Competent Authority for 
purposes of 49 CFR part 107.
    Competent Authority Approval means an approval by the competent 
authority that is required under an international standard (for example, 
the ICAO Technical Instructions for the Safe Transport of Dangerous 
Goods by Air and the International Maritime Dangerous Goods Code). Any 
of the following may be considered a competent authority approval if it 
satisfies the requirement of an international standard:
    (1) A specific regulation in subchapter A or C of this chapter.
    (2) A special permit or approval issued under subchapter A or C of 
this chapter.
    (3) A separate document issued to one or more persons by the 
Associate Administrator.
    Federal hazardous material transportation law means 49 U.S.C. 5101 
et seq.
    File or Filed means received by the appropriate PHMSA or other 
designated office within the time specified in a regulation or 
rulemaking document.

[[Page 8]]

    Hazardous material means a substance or material that the Secretary 
of Transportation has determined is capable of posing an unreasonable 
risk to health, safety, and property when transported in commerce, and 
has designated as hazardous under section 5103 of Federal hazardous 
materials transportation law (49 U.S.C. 5103). The term includes 
hazardous substances, hazardous wastes, marine pollutants, elevated 
temperature materials, materials designated as hazardous in the 
Hazardous Materials Table (see 49 CFR 172.101), and materials that meet 
the defining criteria for hazard classes and divisions in part 173 of 
subchapter C of this chapter.
    Hazardous Materials Regulations or HMR means the regulations at 49 
CFR parts 171 through 180.
    Indian tribe has the same meaning given that term in section 4 of 
the Indian Self-Determination and Education Assistance Act (25 U.S.C. 
450b).
    Person means an individual, firm, copartnership, corporation, 
company, association, or joint-stock association (including any trustee, 
receiver, assignee, or similar representative); or a government or 
Indian tribe (or an agency or instrumentality of any government or 
Indian tribe) that transports a hazardous material to further a 
commercial enterprise or offers a hazardous material for transportation 
in commerce. Person does not include the following:
    (1) The United States Postal Service.
    (2) Any agency or instrumentality of the Federal government, for the 
purposes of 49 U.S.C. 5123 (civil penalties) and 5124 (criminal 
penalties).
    (3) Any government or Indian tribe (or an agency or instrumentality 
of any government or Indian tribe) that transports hazardous material 
for a governmental purpose.
    Political subdivision means a municipality; a public agency or other 
instrumentality of one or more States, municipalities, or other 
political body of a State; or a public corporation, board, or commission 
established under the laws of one or more States.
    Preemption determination means an administrative decision by the 
Associate Administrator that Federal hazardous materials law does or 
does not void a specific State, political subdivision, or Indian tribe 
requirement.
    Regulations issued under Federal hazardous material transportation 
law include this subchapter A (parts 105-110) and subchapter C (parts 
171-180) of this chapter, certain regulations in chapter I (United 
States Coast Guard) of title 46, Code of Federal Regulations, and in 
chapters III (Federal Motor Carrier Safety Administration) and XII 
(Transportation Security Administration) of subtitle B of this title, as 
indicated by the authority citations therein.
    Special permit means a document issued by the Associate 
Administrator under the authority of 49 U.S.C. 5117 permitting a person 
to perform a function that is not otherwise permitted under subchapter A 
or C of this chapter, or other regulations issued under 49 U.S.C. 5101 
et seq. (e.g., Federal Motor Carrier Safety routing requirements). The 
terms ``special permit'' and ``exemption'' have the same meaning for 
purposes of subchapter A or C of this chapter or other regulations 
issued under 49 U.S.C. 5101 through 5127. An exemption issued prior to 
October 1, 2005 remains valid until it is past its expiration date, 
terminated by the Associate Administrator, or is issued as a special 
permit, whichever occurs first.
    State means a State of the United States, the District of Columbia, 
the Commonwealth of Puerto Rico, the Commonwealth of the Northern 
Mariana Islands, the Virgin Islands, American Samoa, Guam, or any other 
territory or possession of the United States designated by the 
Secretary.
    Transports or Transportation means the movement of property and 
loading, unloading, or storage incidental to the movement.
    Waiver of Preemption means a decision by the Associate Administrator 
to forego preemption of a non-Federal requirement--that is, to allow a 
State, political subdivision or Indian tribe requirement to remain in 
effect. The non-Federal requirement must provide at least as much public 
protection as the Federal hazardous materials transportation law and the 
regulations

[[Page 9]]

issued under Federal hazardous materials transportation law, and may not 
unreasonably burden commerce.

[67 FR 42951, June 25, 2002, as amended at 68 FR 52846, Sept. 8, 2003; 
70 FR 56087, Sept. 23, 2005; 70 FR 73158, Dec. 9, 2005]



                      Subpart B_General Procedures



Sec. 105.15  Defined terms used in this subpart.

    The following defined terms (see subpart A of this part) appear in 
this subpart: Approval; Federal hazardous material transportation law; 
Hazardous material; Hazardous materials regulations; Indian tribe; 
Preemption determination; Special permit; State; Transportation; Waiver 
of preemption

[67 FR 42951, June 25, 2002, as amended at 70 FR 73159, Dec. 9, 2005]

                Obtaining Guidance and Public Information



Sec. 105.20  Guidance and interpretations.

    (a) Hazardous materials regulations. You can obtain information and 
answers to your questions on compliance with the hazardous materials 
regulations (49 CFR parts 171 through 180) and interpretations of those 
regulations by contacting PHMSA's Office of Hazardous Materials Safety 
as follows:
    (1) Call the Hazardous Materials Information Center at 1-800-467-
4922 (in Washington, DC, call (202) 366-4488). The Center is staffed 
from 9 a.m. through 5 p.m. Eastern time, Monday through Friday except 
Federal holidays. After hours, you can leave a recorded message and your 
call will be returned by the next business day.
    (2) E-mail the Hazardous Materials Information Center at 
infocntr@dot.gov.
    (3) Obtain hazardous materials safety information via the Internet 
at http://www.phmsa.dot.gov.
    (4) Send a letter, with your return address and a daytime telephone 
number, to: Standards and Rulemaking Division, Pipeline and Hazardous 
Materials Safety Administration, Attn: PHH-10, U.S. Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington, 
DC 20590-0001.
    (b) Federal hazardous materials transportation law and preemption. 
You can obtain information and answers to your questions on Federal 
hazardous materials transportation law, 49 U.S.C. 5101 et seq., and 
Federal preemption of State, local, and Indian tribe hazardous material 
transportation requirements, by contacting PHMSA's Office of the Chief 
Counsel as follows:
    (1) Call the office of the Chief Counsel at (202) 366-4400 from 9 
a.m. to 5 p.m. Eastern time, Monday through Friday except Federal 
holidays.
    (2) Access information from the Office of the Chief Counsel via the 
Internet at http://www.phmsa.dot.gov.
    (3) Send a letter, with your return address and a daytime telephone 
number, to: Office of the Chief Counsel, Pipeline and Hazardous 
Materials Safety Administration, Attn: PHC-10, U.S. Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington, 
DC 20590-0001.
    (4) Contact the Office of the Chief Counsel for a copy of 
applications for preemption determinations, waiver of preemption 
determinations, and inconsistency rulings received by PHMSA before 
February 1, 1997.

[70 FR 56087, Sept. 23, 2005, as amended at 72 FR 55682, Oct. 1, 2007; 
76 FR 56310, Sept. 13, 2011]



Sec. 105.25  Reviewing public documents.

    PHMSA is required by statute to make certain documents and 
information available to the public. You can review and copy publicly 
available documents and information at the locations described in this 
section.
    (a) DOT Docket Management System. Unless a particular document says 
otherwise, the following documents are available for public review and 
copying at the Department of Transportation's Docket Management System, 
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001, or for review and downloading through the 
Internet at http://www.regulations.gov.
    (1) Rulemaking documents in proceedings started after February 1, 
1997, including notices of proposed rulemaking, advance notices of 
proposed rulemaking, public comments, related Federal Register notices, 
final rules, appeals, and PHMSA's decisions in response to appeals.

[[Page 10]]

    (2) Applications for special permits numbered DOT-E or DOT-SP 11832 
and above. Also available are supporting data, memoranda of any informal 
meetings with applicants, related Federal Register notices, public 
comments, and decisions granting or denying applications for special 
permits.
    (3) Applications for preemption determinations and waiver of 
preemption determinations received by PHMSA after February 1, 1997. Also 
available are public comments, Federal Register notices, and PHMSA's 
rulings, determinations, decisions on reconsideration, and orders issued 
in response to those applications.
    (b) Office of Pipeline and Hazardous Materials Safety 
Administration's Office of Hazardous Materials Safety. (1) You may 
obtain documents (e.g., proposed and final rules, notices, letters of 
clarification, safety notices, DOT forms and other documents) by 
contacting the Hazardous Materials Information Center at 1-800-467-4922 
or through the Internet at http://www.phmsa.dot.gov.
    (2) Upon your written request, we will make the following documents 
and information available to you:
    (i) Appeals under 49 CFR part 107 and PHMSA's decisions issued in 
response to those appeals.
    (ii) Records of compliance order proceedings and PHMSA compliance 
orders.
    (iii) Applications for approvals, including supporting data, 
memoranda of any informal meetings with applicants, and decisions 
granting or denying approvals applications.
    (iv) Applications for special permits numbered below DOT-E or DOT-SP 
11832 and related background information are available for public review 
and copying at the Office of Hazardous Materials Safety, Approvals and 
Permits Division, U.S. Department of Transportation, PHH-30, East 
Building, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001.
    (v) Other information about PHMSA's hazardous materials program 
required by statute to be made available to the public for review and 
copying and any other information PHMSA decides should be available to 
the public.
    (3) Your written request to review documents should include the 
following:
    (i) A detailed description of the documents you wish to review.
    (ii) Your name, address, and telephone number.
    (4) Send your written request to: Associate Administrator for 
Hazardous Materials Safety, Pipeline and Hazardous Materials Safety 
Administration, Attn: PHH-1, U.S. Department of Transportation, East 
Building, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001.

[70 FR 56088, Sept. 23, 2005, as amended at 70 FR 73159, Dec. 9, 2005; 
72 FR 55682, Oct. 1, 2007; 76 FR 56310, Sept. 13, 2011]



Sec. 105.26  Obtaining records on file with PHMSA.

    To obtain records on file with PHMSA, other than those described in 
Sec. 105.25, you must file a request with PHMSA under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552). The procedures for filing a FOIA 
request are contained in 49 CFR part 7.



Sec. 105.30  Information made available to the public and request for 

confidential treatment.

    When you submit information to PHMSA during a rulemaking proceeding, 
as part of your application for special permit or approval, or for any 
other reason, we may make that information publicly available unless you 
ask that we keep the information confidential.
    (a) Asking for confidential treatment. You may ask us to give 
confidential treatment to information you give to the agency by taking 
the following steps:
    (1) Mark ``confidential'' on each page of the original document you 
would like to keep confidential.
    (2) Send us, along with the original document, a second copy of the 
original document with the confidential information deleted.
    (3) Explain why the information you are submitting is confidential 
(for example, it is exempt from mandatory public disclosure under the 
Freedom of Information Act, 5 U.S.C. 552 or it is information referred 
to in 18 U.S.C. 1905).

[[Page 11]]

    (b) PHMSA Decision. PHMSA will decide whether or not to treat your 
information as confidential. We will notify you, in writing, of a 
decision to grant or deny confidentiality at least five days before the 
information is publicly disclosed, and give you an opportunity to 
respond.

[67 FR 42951, June 25, 2002, as amended at 70 FR 73159, Dec. 9, 2005]

                            Serving Documents



Sec. 105.35  Serving documents in PHMSA proceedings.

    (a) Service by PHMSA. We may serve the document by one of the 
following methods, except where a different method of service is 
specifically required:
    (1) Registered or certified mail.
    (i) If we serve a document by registered or certified mail, it is 
considered served when mailed.
    (ii) An official United States Postal Service receipt from the 
registered or certified mailing is proof of service.
    (iii) We may serve a person's authorized representative or agent by 
registered or certified mail, or in any other manner authorized by law. 
Service on a person's authorized agent is the same as service on the 
person.
    (2) Personal service.
    (3) Publication in the Federal Register.
    (4) Electronic service. (i) Service by electronic means if consented 
to in writing by the party to be served.
    (ii) For all special permits and approvals actions, electronic 
service is authorized.
    (b) Service by others. If you are required under this subchapter to 
serve a person with a document, serve the document by one of the 
following methods, except where a different method of service is 
specifically required:
    (1) Registered or certified mail.
    (i) If you serve a document by registered or certified mail, it is 
considered served when mailed.
    (ii) An official United States Postal Service receipt from the 
registered or certified mailing is proof of service.
    (iii) You may serve a person's authorized representative or agent by 
registered or certified mail or in any other manner authorized by law. 
Service on a person's authorized agent is the same as service on the 
person.
    (2) Personal service.
    (3) Electronic service.
    (i) In a proceeding under Sec. 107.317 of this subchapter (an 
administrative law judge proceeding), you may electronically serve 
documents on us.
    (ii) Serve documents electronically through the Internet at http://
www.regulations.gov.

[67 FR 42951, June 25, 2002, as amended at 72 FR 55682, Oct. 1, 2007; 76 
FR 460, Jan. 5, 2011]



Sec. 105.40  Designated agents for non-residents.

    (a) General requirement. If you are not a resident of the United 
States but are required by this subchapter or subchapter C of this 
chapter to designate a permanent resident of the United States to act as 
your agent and receive documents on your behalf, you must prepare a 
designation and file it with us.
    (b) Agents. An agent, also known as ``agent for service of 
process'':
    (1) May be an individual, a firm, or a domestic corporation.
    (2) May represent any number of principals.
    (3) May not reassign responsibilities under a designation to another 
person.
    (c) Preparing a designation. Your designation must be written and 
dated, and it must contain the following information:
    (1) The section in the HMR that requires you to file a designation.
    (2) A certification that the designation is in the correct legal 
form required to make it valid and binding on you under the laws, 
corporate bylaws, and other requirements that apply to designations at 
the time and place you are making the designation.
    (3) Your full legal name, the principal name of your business, and 
your mailing address.
    (4) A statement that your designation will remain in effect until 
you withdraw or replace it.
    (5) The legal name and mailing address of your agent.
    (6) A declaration of acceptance signed by your agent.
    (d) Address. Send your designation to: Approvals and Permits 
Division, Pipeline and Hazardous Materials Safety

[[Page 12]]

Administration, Attn: PHH-30, U.S. Department of Transportation, East 
Building, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001.
    (e) Designations are binding. You are bound by your designation of 
an agent, even if you did not follow all the requirements in this 
section, until we reject your designation.

[67 FR 42951, June 25, 2002, as amended at 70 FR 56088, Sept. 23, 2005; 
70 FR 73159, Dec. 9, 2005; 72 FR 55682, Oct. 1, 2007; 75 FR 27211, May 
14, 2010; 76 FR 56310, Sept. 13, 2011]

                                Subpoenas



Sec. 105.45  Issuing a subpoena.

    (a) Subpoenas explained. A subpoena is a document that may require 
you to attend a proceeding, produce documents or other physical evidence 
in your possession or control, or both. PHMSA may issue a subpoena 
either on its initiative or at the request of someone participating in a 
proceeding. Anyone who requests that PHMSA issue a subpoena must show 
that the subpoena seeks information that will materially advance the 
proceeding.
    (b) Attendance and mileage expenses. (1) If you receive a subpoena 
to attend a proceeding under this part, you may receive money to cover 
attendance and mileage expenses. The attendance and mileage fees will be 
the same as those paid to a witness in a proceeding in the district 
courts of the United States.
    (2) If PHMSA issues a subpoena to you based upon a request, the 
requester must serve a copy of the original subpoena on you, as required 
in Sec. 105.50. The requester must also include attendance and mileage 
fees with the subpoena unless the requester asks PHMSA to pay the 
attendance and mileage fees because of demonstrated financial hardship 
and PHMSA agrees to do so.
    (3) If PHMSA issues a subpoena at the request of an officer or 
agency of the Federal government, the officer or agency is not required 
to include attendance and mileage fees when serving the subpoena. The 
officer or agency must pay the fees before you leave the hearing at 
which you testify.



Sec. 105.50  Serving a subpoena.

    (a) Personal service. Anyone who is not an interested party and who 
is at least 18 years of age may serve you with a subpoena and fees by 
handing the subpoena and fees to you, by leaving them at your office 
with the individual in charge, or by leaving them at your house with 
someone who lives there and is capable of making sure that you receive 
them. If PHMSA issues a subpoena to an entity, rather than an 
individual, personal service is made by delivering the subpoena and fees 
to the entity's registered agent for service of process or to any 
officer, director or agent in charge of any of the entity's offices.
    (b) Service by mail. You may be served with a copy of a subpoena and 
fees by certified or registered mail at your last known address. Service 
of a subpoena and fees may also be made by registered or certified mail 
to your agent for service of process or any of your representatives at 
that person's last known address.
    (c) Other methods. You may be served with a copy of a subpoena by 
any method where you receive actual notice of the subpoena and receive 
the fees before leaving the hearing at which you testify.
    (d) Filing after service. After service is complete, the individual 
who served a copy of a subpoena and fees must file the original subpoena 
and a certificate of service with the PHMSA official who is responsible 
for conducting the hearing.



Sec. 105.55  Refusal to obey a subpoena.

    (a) Quashing or modifying a subpoena. If you receive a subpoena, you 
can ask PHMSA to overturn (``quash'') or modify the subpoena within 10 
days after the subpoena is served on you. Your request must briefly 
explain the reasons you are asking for the subpoena to be quashed or 
modified. PHMSA may then do the following:
    (1) Deny your request.
    (2) Quash or modify the subpoena.
    (3) Grant your request on the condition that you satisfy certain 
specified requirements.
    (b) Failure to obey. If you disobey a subpoena, PHMSA may ask the 
Attorney General to seek help from the

[[Page 13]]

United States District Court for the appropriate District to compel you, 
after notice, to appear before PHMSA and give testimony, produce 
subpoenaed documents or physical evidence, or both.



PART 106_RULEMAKING PROCEDURES--Table of Contents



                  Subpart A_PHMSA Rulemaking Documents

Sec.
106.5 Defined terms used in this subpart.
106.10 Process for issuing rules.
106.15 Advance notice of proposed rulemaking.
106.20 Notice of proposed rulemaking.
106.25 Revising regulations without first issuing an ANPRM or NPRM.
106.30 Final rule.
106.35 Interim final rule.
106.40 Direct final rule.
106.45 Tracking rulemaking actions.

            Subpart B_Participating in the Rulemaking Process

106.50 Defined terms used in this subpart.
106.55 Public participation in the rulemaking process.

                            Written Comments

106.60 Filing comments.
106.65 Required information for written comments.
106.70 Where and when to file comments.
106.75 Extension of time to file comments.

                  Public Meetings and Other Proceedings

106.80 Public meeting procedures.
106.85 Requesting a public meeting.
106.90 Other rulemaking proceedings.

                        Petitions for Rulemaking

106.95 Requesting a change to the regulations.
106.100 Required information for a petition for rulemaking.
106.105 PHMSA response to a petition for rulemaking.

                                 Appeals

106.110 Appealing a PHMSA action.
106.115 Required information for an appeal.
106.120 Appeal deadline.
106.125 Filing an appeal.
106.130 PHMSA response to an appeal.

    Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.

    Source: 67 FR 42954, June 25, 2002, unless otherwise noted.

    Editorial Note: Nomenclature changes to part 106 appear at 70 FR 
56088, Sept. 23, 2005.



                  Subpart A_PHMSA Rulemaking Documents



Sec. 106.5  Defined terms used in this subpart.

    The following defined terms (see part 105, subpart A, of this 
subchapter) appear in this subpart: File; Person; State.



Sec. 106.10  Process for issuing rules.

    (a) PHMSA (``we'') uses informal rulemaking procedures under the 
Administrative Procedure Act (5 U.S.C. 553) to add, amend, or delete 
regulations. To propose or adopt changes to a regulation, PHMSA may 
issue one or more of the following documents. We publish the following 
rulemaking documents in the Federal Register unless we name and 
personally serve a copy of a rule on every person subject to it:
    (1) An advance notice of proposed rulemaking.
    (2) A notice of proposed rulemaking.
    (3) A final rule.
    (4) An interim final rule.
    (5) A direct final rule.
    (b) Each of the rulemaking documents in paragraph (a) of this 
section generally contains the following information:
    (1) The topic involved in the rulemaking document.
    (2) PHMSA's legal authority for issuing the rulemaking document.
    (3) How interested persons may participate in the rulemaking 
proceeding (for example, by filing written comments or making oral 
presentations).
    (4) Whom to call if you have questions about the rulemaking 
document.
    (5) The date, time, and place of any public meetings being held to 
discuss the rulemaking document.
    (6) The docket number and regulation identifier number (RIN) for the 
rulemaking proceeding.

[67 FR 42954, June 25, 2002, as amended at 70 FR 56088, Sept. 23, 2005]



Sec. 106.15  Advance notice of proposed rulemaking.

    An advance notice of proposed rulemaking (ANPRM) tells the public 
that

[[Page 14]]

PHMSA is considering an area for rulemaking and requests written 
comments on the appropriate scope of the rulemaking or on specific 
topics. An advance notice of proposed rulemaking may or may not include 
the text of potential changes to a regulation.



Sec. 106.20  Notice of proposed rulemaking.

    A notice of proposed rulemaking (NPRM) contains PHMSA's specific 
proposed regulatory changes for public comment and contains supporting 
information. It generally includes proposed regulatory text.



Sec. 106.25  Revising regulations without first issuing an ANPRM or NPRM.

    PHMSA may add, amend, or delete regulations without first issuing an 
ANPRM or NPRM in the following situations:
    (a) We may go directly to a final rule or interim final rule if, for 
good cause, we find that a notice of proposed rulemaking is 
impracticable, unnecessary, or contrary to the public interest. We must 
place that finding and a brief statement of the reasons for it in the 
final rule or interim final rule.
    (b) We may issue a direct final rule (see Sec. 106.40).



Sec. 106.30  Final rule.

    A final rule sets out new regulatory requirements and their 
effective date. A final rule will also identify issues raised by 
commenters in response to the notice of proposed rulemaking and give the 
agency's response.



Sec. 106.35  Interim final rule.

    An interim final rule is issued without first issuing a notice of 
proposed rulemaking and accepting public comments and sets out new 
regulatory requirements and their effective date. PHMSA may issue an 
interim final rule if it finds, for good cause, that notice and public 
procedure are impracticable, unnecessary, or contrary to the public 
interest. PHMSA will clearly set out this finding in the interim final 
rule. After receiving and reviewing public comments, as well as any 
other relevant documents, PHMSA may revise the interim final rule and 
then issue a final rule.



Sec. 106.40  Direct final rule.

    A direct final rule makes regulatory changes and states that the 
regulatory changes will take effect on a specified date unless PHMSA 
receives an adverse comment or notice of intent to file an adverse 
comment within the comment period--generally 60 days after the direct 
final rule is published in the Federal Register.
    (a) Actions taken by direct final rule. We may use direct final 
rulemaking procedures to issue rules that do any of the following:
    (1) Make minor substantive changes to regulations.
    (2) Incorporate by reference the latest edition of technical or 
industry standards.
    (3) Extend compliance dates.
    (4) Make noncontroversial changes to regulations. We must determine 
and publish a finding that use of direct final rulemaking, in this 
situation, is in the public interest and unlikely to result in adverse 
comment.
    (b) Adverse comment. An adverse comment explains why a rule would be 
inappropriate, or would be ineffective or unacceptable without a change. 
It may challenge the rule's underlying premise or approach. Under the 
direct final rule process, we do not consider the following types of 
comments to be adverse:
    (1) A comment recommending another rule change, in addition to the 
change in the direct final rule at issue, unless the commenter states 
why the direct final rule would be ineffective without the change.
    (2) A frivolous or irrelevant comment.
    (c) Confirmation of effective date. We will publish a confirmation 
document in the Federal Register, generally within 15 days after the 
comment period closes, if we have not received an adverse comment or 
notice of intent to file an adverse comment. The confirmation document 
tells the public the effective date of the rule--either the date stated 
in the direct final rule or at least 30 days after the publication date 
of the confirmation document, whichever is later.
    (d) Withdrawing a direct final rule. (1) If we receive an adverse 
comment or

[[Page 15]]

notice of intent to file an adverse comment, we will publish a document 
in the Federal Register before the effective date of the direct final 
rule advising the public and withdrawing the direct final rule in whole 
or in part.
    (2) If we withdraw a direct final rule because of an adverse 
comment, we may incorporate the adverse comment into a later direct 
final rule or may publish a notice of proposed rulemaking.
    (e) Appeal. You may appeal PHMSA's issuance of a direct final rule 
(see Sec. 106.115) only if you have previously filed written comments 
(see Sec. 106.60) to the direct final rule.



Sec. 106.45  Tracking rulemaking actions.

    The following identifying numbers allow you to track PHMSA's 
rulemaking activities:
    (a) Docket number. We assign an identifying number, called a docket 
number, to each rulemaking proceeding. Each rulemaking document that 
PHMSA issues in a particular rulemaking proceeding will display the same 
docket number. This number allows you to do the following:
    (1) Associate related documents that appear in the Federal Register.
    (2) Search the DOT Docket Management System (``DMS'') for 
information on particular rulemaking proceedings--including notices of 
proposed rulemaking, public comments, petitions for rulemaking, appeals, 
records of additional rulemaking proceedings and final rules. There are 
two ways you can search the DMS:
    (i) Visit the public docket room and review and copy any docketed 
materials during regular business hours. The DOT Docket Management 
System is located at the U.S. Department of Transportation, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001.
    (ii) View and download docketed materials through the Internet at 
http://www.regulations.gov.
    (b) Regulation identifier number. The Department of Transportation 
publishes a semiannual agenda of all current and projected Department of 
Transportation rulemakings, reviews of existing regulations, and 
completed actions. This semiannual agenda appears in the Unified Agenda 
of Federal Regulations that is published in the Federal Register in 
April and October of each year. The semiannual agenda tells the public 
about the Department's--including PHMSA's--regulatory activities. The 
Department assigns a regulation identifier number (RIN) to each 
individual rulemaking proceeding in the semiannual agenda. This number 
appears on all rulemaking documents published in the Federal Register 
and makes it easy for you to track those rulemaking proceedings in both 
the Federal Register and the semiannual regulatory agenda itself, as 
well as to locate all documents in the Docket Management System 
pertaining to a particular rulemaking.

[70 FR 56088, Sept. 23, 2005, as amended at 72 FR 55682, Oct. 1, 2007]



            Subpart B_Participating in the Rulemaking Process



Sec. 106.50  Defined terms used in this subpart.

    The following defined terms (see part 105, subpart A, of this 
subchapter) appear in this subpart: File; Person; Political subdivision; 
State.



Sec. 106.55  Public participation in the rulemaking process.

    You may participate in PHMSA's rulemaking process by doing any of 
the following:
    (a) File written comments on any rulemaking document that asks for 
comments, including an advance notice of proposed rulemaking, notice of 
proposed rulemaking, interim final rule, or direct final rule.
    (b) Ask that we hold a public meeting in any rulemaking proceeding 
and participate in any public meeting that we hold.
    (c) File a petition for rulemaking that asks us to add, amend, or 
delete a regulation.
    (d) File an appeal that asks us to reexamine our decision to issue 
all or part of a final rule, interim final rule, or direct final rule.

[[Page 16]]

                            Written Comments



Sec. 106.60  Filing comments.

    Anyone may file written comments about proposals made in any 
rulemaking document that requests public comments, including any State 
government agency, any political subdivision of a State, and any 
interested person invited by PHMSA to participate in the rulemaking 
process.



Sec. 106.65  Required information for written comments.

    Your comments must be in English and must contain the following:
    (a) The docket number of the rulemaking document you are commenting 
on, clearly set out at the beginning of your comments.
    (b) Information, views, or arguments that follow the instructions 
for participation that appear in the rulemaking document on which you 
are commenting.
    (c) All material that is relevant to any statement of fact in your 
comments.
    (d) The document title and page number of any material that you 
reference in your comments.



Sec. 106.70  Where and when to file comments.

    (a) Unless you are told to do otherwise in the rulemaking document 
on which you are commenting, send your comments to us in either of the 
following ways:
    (1) By mail to: Docket Management System, U.S. Department of 
Transportation, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590-0001.
    (2) Through the Internet at http://www.regulations.gov.
    (b) Make sure that your comments reach us by the deadline set out in 
the rulemaking document on which you are commenting. We will consider 
late filed comments to the extent possible.
    (c) We may reject comments that are not relevant to the rulemaking. 
We may reject comments you file electronically if you do not follow the 
electronic filing instructions at the DOT Web site.

[67 FR 42954, June 25, 2002, as amended at 69 FR 54044, Sept. 7, 2004; 
72 FR 55682, Oct. 1, 2007]



Sec. 106.75  Extension of time to file comments.

    You may ask for more time to file comments on a rulemaking 
proceeding. If PHMSA grants your request, it is granted to all persons. 
We will notify the public of the extension by publishing a document in 
the Federal Register. If PHMSA denies your request, PHMSA will notify 
you of the denial. To ask for more time, you must do the following:
    (a) File a request for extension at least ten days before the end of 
the comment period established in the rulemaking document.
    (b) Show that you have good cause for the extension and that an 
extension is in the public interest.
    (c) Include the docket number of the rulemaking document you are 
seeking additional time to comment on, clearly set out at the beginning 
of your request.
    (d) Send your request to: Docket Management System, U.S. Department 
of Transportation, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590-0001.

[67 FR 42954, June 25, 2002, as amended at 72 FR 55682, Oct. 1, 2007]

                  Public Meetings and Other Proceedings



Sec. 106.80  Public meeting procedures.

    A public meeting is a non-adversarial, fact-finding proceeding 
conducted by a PHMSA representative. Generally, public meetings are 
announced in the Federal Register. Interested persons are invited to 
attend and to present their views to the agency on specific issues. 
There are no formal pleadings and no adverse parties, and any regulation 
issued afterward is not necessarily based exclusively on the record of 
the meeting. Sections 556 and 557 of the Administrative Procedure Act (5 
U.S.C. 556 and 557) do not apply to public meetings under this part.

[[Page 17]]



Sec. 106.85  Requesting a public meeting.

    (a) You may ask for a public meeting by filing a written request 
with PHMSA no later than 20 days before the expiration of the comment 
period specified in the rulemaking document. Send your request for a 
public meeting to: Docket Management System, U.S. Department of 
Transportation, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590-0001.
    (b) PHMSA will review your request and, if you have shown good cause 
for a public meeting, we will grant it and publish a notice of the 
meeting in the Federal Register.

[67 FR 42954, June 25, 2002, as amended at 72 FR 55682, Oct. 1, 2007]



Sec. 106.90  Other rulemaking proceedings.

    During a rulemaking proceeding, PHMSA may invite you to do the 
following:
    (a) Participate in a conference at which minutes are taken.
    (b) Make an oral presentation.
    (c) Participate in any other public proceeding to ensure that PHMSA 
makes informed decisions during the rulemaking process and to protect 
the public interest, including a negotiated rulemaking or work group led 
by a facilitator.

                        Petitions for Rulemaking



Sec. 106.95  Requesting a change to the regulations.

    You may ask PHMSA to add, amend, or delete a regulation by filing a 
petition for rulemaking as follows:
    (a) For regulations in 49 CFR parts 110, 130, 171 through 180, 
submit the petition to: Standards and Rulemaking Division, Pipeline and 
Hazardous Materials Safety Administration, Attn: PHH-10, U.S. Department 
of Transportation, East Building, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001.
    (b) For regulations in 49 CFR parts 105, 106, or 107, submit the 
petition to: Office of the Chief Counsel, Pipeline and Hazardous 
Materials Safety Administration, Attn: PHC-10, U.S. Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington, 
DC 20590-0001.

[70 FR 56089, Sept. 23, 2005, as amended at 72 FR 55683, Oct. 1, 2007; 
76 FR 56310, Sept. 13, 2011]



Sec. 106.100  Required information for a petition for rulemaking.

    (a) You must include the following information in your petition for 
rulemaking:
    (1) A summary of your proposed action and an explanation of its 
purpose.
    (2) The language you propose for a new or amended rule, or the 
language you would delete from a current rule.
    (3) An explanation of your interest in your proposed action and the 
interest of anyone you may represent.
    (4) Information and arguments that support your proposed action, 
including relevant technical and scientific data available to you.
    (5) Any specific cases that support or demonstrate the need for your 
proposed action.
    (b) If the impact of your proposed action is substantial, and data 
or other information about that impact are available to you, we may ask 
that you provide information about the following:
    (1) The costs and benefits of your proposed action to society in 
general, and identifiable groups within society in particular.
    (2) The direct effects, including preemption effects under section 
5125 of Federal hazardous materials transportation law, of your proposed 
action on States, on the relationship between the Federal government and 
the States, and on the distribution of power and responsibilities among 
the various levels of government. (See 49 CFR part 107, subpart C, 
regarding preemption.)
    (3) The regulatory burden of your proposed action on small 
businesses, small organizations, small governmental jurisdictions, and 
Indian tribes.
    (4) The recordkeeping and reporting burdens of your proposed action 
and whom they would affect.
    (5) The effect of your proposed action on the quality of the natural 
and social environments.

[[Page 18]]



Sec. 106.105  PHMSA response to a petition for rulemaking.

    We will review and respond to your petition for rulemaking as 
follows:

------------------------------------------------------------------------
                                       And if we
    If your petition is . . .      determine  that .      Then . . .
                                          . .
------------------------------------------------------------------------
(a) Incomplete..................  ..................  We may return your
                                                       petition with a
                                                       written
                                                       explanation.
------------------------------------------------------------------------
(b) Complete....................  Your petition does  We will notify you
                                   not justify a       in writing that
                                   rulemaking action.  we will not start
                                                       a rulemaking
                                                       proceeding.
------------------------------------------------------------------------
(c) Complete....................  Your petition does  We will notify you
                                   justify a           in writing that
                                   rulemaking action.  we will start a
                                                       rulemaking
                                                       proceeding.
------------------------------------------------------------------------

                                 Appeals



Sec. 106.110  Appealing a PHMSA Action.

    You may appeal the following PHMSA actions:
    (a) PHMSA's issuance of a final rule or PHMSA's withdrawal of a 
notice of proposed rulemaking under the rulemaking procedures in this 
part. However, you may appeal PHMSA's issuance of a direct final rule 
only if you previously filed comments to the direct final rule (see 
Sec. 106.40(e)).
    (b) Any PHMSA decision on a petition for rulemaking.



Sec. 106.115  Required information for an appeal.

    (a) Appeal of a final rule or withdrawal of a notice of proposed 
rulemaking. If you appeal PHMSA's issuance of a final rule or PHMSA's 
withdrawal of a notice of proposed rulemaking, your appeal must include 
the following:
    (1) The docket number of the rulemaking you are concerned about, 
clearly set out at the beginning of your appeal.
    (2) A brief statement of your concern about the final rule or the 
withdrawal of notice of proposed rulemaking at issue.
    (3) An explanation of why compliance with the final rule is not 
practical, reasonable, or in the public interest.
    (4) If you want PHMSA to consider more facts, the reason why you did 
not present those facts within the time given during the rulemaking 
process for public comment.
    (b) Appeal of a decision. If you appeal PHMSA's decision on a 
petition for rulemaking, you must include the following:
    (1) The contested aspects of the decision.
    (2) Any new arguments or information.



Sec. 106.120  Appeal deadline.

    (a) Appeal of a final rule or withdrawal of a notice of proposed 
rulemaking. If you appeal PHMSA's issuance of a final rule or PHMSA's 
withdrawal of a proposed rulemaking, your appeal document must reach us 
no later than 30 days after the date PHMSA published the regulation or 
the withdrawal notice in the Federal Register. After that time, PHMSA 
will consider your appeal to be a petition for rulemaking under Sec. 
106.100.
    (b) Appeal of a decision. If you appeal PHMSA's decision on a 
petition for rulemaking, your appeal document must reach us no later 
than 30 days from the date PHMSA served you with written notice of 
PHMSA's decision.

[70 FR 56089, Sept. 23, 2005]



Sec. 106.125  Filing an appeal.

    Send your appeal to: Docket Management System, U.S. Department of 
Transportation, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590-0001.

[67 FR 42954, June 25, 2002, as amended at 72 FR 55682, Oct. 1, 2007]



Sec. 106.130  PHMSA response to an appeal.

    Unless PHMSA provides otherwise, filing an appeal will not keep a 
final rule from becoming effective. We will handle an appeal according 
to the following procedures:
    (a) Appeal of a final rule or withdrawal of a notice of proposed 
rulemaking. (1) We may consolidate your appeal with other appeals of the 
same rule.
    (2) We may grant or deny your appeal, in whole or in part, without 
further rulemaking proceedings, unless granting your appeal would result 
in the issuance of a new final rule.

[[Page 19]]

    (3) If we decide to grant your appeal, we may schedule further 
proceedings and an opportunity to comment.
    (4) PHMSA will notify you, in writing, of the action on your appeal 
within 90 days after the date that PHMSA published the final rule or 
withdrawal of notice of proposed rulemaking at issue in the Federal 
Register. If we do not issue a decision on your appeal within the 90-day 
period and we anticipate a substantial delay, we will notify you 
directly about the delay and will give you an expected decision date. We 
will also publish a notice of the delay in the Federal Register.
    (b) Appeal of a decision. (1) We will not consider your appeal if it 
merely repeats arguments that PHMSA has previously rejected.
    (2) PHMSA will notify you, in writing, of the action on your appeal 
within 90 days after the date that PHMSA served you with written notice 
of its decision on your petition for rulemaking. If we do not issue a 
decision on your appeal within the 90-day period, and we anticipate a 
substantial delay, we will notify you directly about the delay and will 
give you an expected decision date.



PART 107_HAZARDOUS MATERIALS PROGRAM PROCEDURES--Table of Contents



                          Subpart A_Definitions

Sec.
107.1 Definitions.

                        Subpart B_Special Permits

107.101 Purpose and scope.
107.105 Application for special permit.
107.107 Application for party status.
107.109 Application for renewal.
107.111 Withdrawal.
107.113 Application processing and evaluation.
107.117 Emergency processing.
107.121 Modification, suspension or termination of special permit or 
          grant of party status.
107.123 Reconsideration.
107.125 Appeal.
107.127 Availability of documents for public inspection.

                          Subpart C_Preemption

107.201 Purpose and scope.
107.202 Standards for determining preemption.

                        Preemption Determinations

107.203 Application.
107.205 Notice.
107.207 Processing.
107.209 Determination.
107.211 Petition for reconsideration.
107.213 Judicial review.

                   Waiver of Preemption Determinations

107.215 Application.
107.217 Notice.
107.219 Processing.
107.221 Determination.
107.223 Petition for reconsideration.
107.227 Judicial review.

                          Subpart D_Enforcement

107.301 Delegated authority for enforcement.
107.303 Purpose and scope.
107.305 Investigations.

                  Compliance Orders and Civil Penalties

107.307 General.
107.309 Warning letters.
107.310 Ticketing.
107.311 Notice of probable violation.
107.313 Reply.
107.315 Admission of violations.
107.317 Informal response.
107.319 Request for a hearing.
107.321 Hearing.
107.323 ALJ's decision.
107.325 Appeals.
107.327 Compromise and settlement.
107.329 Maximum penalties.
107.331 Assessment considerations.

                           Criminal Penalties

107.333 Criminal penalties generally.
107.335 Referral for prosecution.
107.336 Limitation on fines and penalties.

                            Injunctive Action

107.337 Injunctions generally.
107.339 Imminent hazards.

Appendix A to Subpart D of Part 107--Guidelines for Civil Penalties

      Subpart E_Designation of Approval and Certification Agencies

107.401 Purpose and scope.
107.402 Application for designation as an approval or certification 
          agency.
107.403 Designation of approval agencies.
107.404 Conditions of designation.
107.405 Termination of designation.

   Subpart F_Registration of Cargo Tank and Cargo Tank Motor Vehicle 
 Manufacturers, Assemblers, Repairers, Inspectors, Testers, and Design 
                          Certifying Engineers

107.501 Scope.

[[Page 20]]

107.502 General registration requirements.
107.503 Registration statement.
107.504 Period of registration, updates, and record retention.

   Subpart G_Registration of Persons Who Offer or Transport Hazardous 
                                Materials

107.601 Applicability.
107.606 Exceptions.
107.608 General registration requirements.
107.612 Amount of fee.
107.616 Payment procedures.
107.620 Recordkeeping requirements.

           Subpart H_Approvals, Registrations and Submissions

107.701 Purpose and scope.
107.705 Registrations, reports, and applications for approval.
107.709 Processing of an application for approval, including an 
          application for renewal or modification.
107.711 Withdrawal.
107.713 Approval modification, suspension or termination.
107.715 Reconsideration.
107.717 Appeal.

    Subpart I_Approval of Independent Inspection Agencies, Cylinder 
   Requalifiers, and Non-domestic Chemical Analyses and Tests of DOT 
                         Specification Cylinders

107.801 Purpose and scope.
107.803 Approval of an independent inspection agency (IIA).
107.805 Approval of cylinder and pressure receptacle requalifiers.
107.807 Approval of non-domestic chemical analyses and tests.
107.809 Conditions of UN pressure receptacle approvals.

    Authority: 49 U.S.C. 5101-5128, 44701; Pub. L. 101-410 section 4 (28 
U.S.C. 2461 note); Pub. L. 104-121 sections 212-213; Pub. L. 104-134 
section 31001; 49 CFR 1.45, 1.53.

    Editorial Note: Nomenclature changes to part 107 appear at 67 FR 
61011, Sept. 27, 2002, 70 FR 56089, Sept. 23, 2005, and 70 FR 73159, 
Dec. 9, 2005.



                          Subpart A_Definitions



Sec. 107.1  Definitions.

    All terms defined in 49 U.S.C. 5102 are used in their statutory 
meaning. Other terms used in this part are defined as follows:
    Acting knowingly means acting or failing to act while
    (1) Having actual knowledge of the facts giving rise to the 
violation, or
    (2) Having the knowledge that a reasonable person acting in the same 
circumstances and exercising due care would have had.
    Administrator means the Administrator, Pipeline and Hazardous 
Materials Safety Administration or his or her delegate.
    Applicant means the person in whose name a special permit, approval, 
registration, a renewed or modified special permit or approval, or party 
status to a special permit is requested to be issued.
    Application means a request under subpart B of this part for a 
special permit, a renewal or modification of a special permit, party 
status to a special permit, or a request under subpart H of this part 
for an approval, or renewal or modification of an approval.
    Approval means written consent, including a competent authority 
approval, from the Associate Administrator or other designated 
Department official, to perform a function that requires prior consent 
under subchapter C of this chapter (49 CFR parts 171 through 180).
    Approval Agency means an organization or a person designated by the 
PHMSA to certify packagings as having been designed, manufactured, 
tested, modified, marked or maintained in compliance with applicable DOT 
regulations.
    Associate Administrator means the Associate Administrator for 
Hazardous Materials Safety, Pipeline and Hazardous Materials Safety 
Administration.
    Competent Authority means a national agency that is responsible, 
under its national law, for the control or regulation of some aspect of 
hazardous materials (dangerous goods) transportation. Another term for 
Competent Authority is ``Appropriate authority,'' which is used in the 
International Civil Aviation Organization's (ICAO) Technical 
Instructions for the Safe Transport of Dangerous Goods by Air. The 
Associate Administrator is the United States Competent Authority for 
purposes of this part 107.
    Competent Authority Approval means an approval by the competent 
authority that is required under an international standard (for example, 
the

[[Page 21]]

ICAO Technical Instructions for the Safe Transport of Dangerous Goods by 
Air and the International Maritime Dangerous Goods Code). Any of the 
following may be considered a competent authority approval if it 
satisfies the requirement of an international standard:
    (1) A specific regulation in subchapter A or C of this chapter.
    (2) A special permit or approval issued under subchapter A or C of 
this chapter.
    (3) A separate document issued to one or more persons by the 
Associate Administrator.
    DOT or Department means U.S. Department of Transportation.
    Federal hazardous material transportation law means 49 U.S.C. 5101 
et seq.
    Filed means received by the appropriate PHMSA or other designated 
office within the time specified in a regulation or rulemaking document.
    Holder means the person in whose name a special permit or approval 
has been issued.
    Imminent Hazard means the existence of a condition which presents a 
substantial likelihood that death, serious illness, severe personal 
injury, or substantial endangerment to health, property, or the 
environment may occur before the reasonably foreseeable completion of an 
administrative hearing or other formal proceeding initiated to abate the 
risks of those effects.
    Incident means an event resulting in the unintended and 
unanticipated release of a hazardous material or an event meeting 
incident reporting requirements in Sec. 171.15 or Sec. 171.16 of this 
chapter.
    Indian Tribe has the same meaning given that term in section 4 of 
the Indian Self-Determination and Education Assistance Act (25 U.S.C. 
450b).
    Investigation includes investigations authorized under 49 U.S.C. 
5121 and inspections authorized under 49 U.S.C. 5118 and 5121.
    Manufacturing special permit means a special permit from compliance 
with specified requirements that otherwise must be met before 
representing, marking, certifying (including requalifying, inspecting, 
and testing), selling or offering a packaging or container as meeting 
the requirements of subchapter C of this chapter governing its use in 
the transportation in commerce of a hazardous material. A manufacturing 
special permit is a special permit issued to a manufacturer of 
packagings who does not offer for transportation or transport hazardous 
materials in packagings subject to the special permit.
    Party means a person, other than a holder, authorized to act under 
the terms of a special permit.
    Person means an individual, firm, copartnership, corporation, 
company, association, or joint-stock association (including any trustee, 
receiver, assignee, or similar representative); or a government or 
Indian tribe (or an agency or instrumentality of any government or 
Indian tribe) that transports a hazardous material to further a 
commercial enterprise or offers a hazardous material for transportation 
in commerce. Person does not include the following:
    (1) The United States Postal Service.
    (2) Any agency or instrumentality of the Federal government, for the 
purposes of 49 U.S.C. 5123 (civil penalties) and 5124 (criminal 
penalties.)
    (3) Any government or Indian tribe (or an agency or instrumentality 
of any government or Indian tribe) that transports hazardous material 
for a governmental purpose.
    Registration means a written acknowledgment from the Associate 
Administrator that a registrant is authorized to perform a function for 
which registration is required under subchapter C of this chapter (e.g., 
registration in accordance with 49 CFR 178.503 regarding marking of 
packagings). For purposes of subparts A through E, ``registration'' does 
not include registration under subpart F or G of this part.
    Report means information, other than an application, registration or 
part thereof, required to be submitted to the Associate Administrator 
pursuant to this subchapter, subchapter B or subchapter C of this 
chapter.
    Respondent means a person upon whom the PHMSA has served a notice of 
probable violation.
    Special permit means a document issued by the Associate 
Administrator,

[[Page 22]]

or other designated Department official, under the authority of 49 
U.S.C. 5117 permitting a person to perform a function that is not 
otherwise permitted under subchapters A or C of this chapter, or other 
regulations issued under 49 U.S.C. 5101 et seq. (e.g., Federal Motor 
Carrier Safety routing requirements).
    State means a State of the United States, the District of Columbia, 
the Commonwealth of Puerto Rico, the Commonwealth of the Northern 
Mariana Islands, the Virgin Islands, American Samoa, Guam, or any other 
territory or possession of the United States designated by the 
Secretary.
    Transports or transportation means the movement of property and 
loading, unloading, or storage incidental to the movement.

[Amdt. 107-3, 41 FR 38170, Sept. 9, 1976]

    Editorial Note: For Federal Register citations affecting Sec. 
107.1, see the List of CFR Sections Affected which appears in the 
Finding Aids section of the printed volume and at www.fdsys.gov.



                        Subpart B_Special Permits

    Source: Amdt. 107-38, 61 FR 21095, May 9, 1996, unless otherwise 
noted.



Sec. 107.101  Purpose and scope.

    This subpart prescribes procedures for the issuance, modification 
and termination of special permits from requirements of this subchapter, 
subchapter C of this chapter, or regulations issued under chapter 51 of 
49 U.S.C.



Sec. 107.105  Application for special permit.

    (a) General. Each application for a special permit or modification 
of a special permit and all supporting documents must be written in 
English and submitted for timely consideration at least 120 days before 
the requested effective date and conform to the following requirements:
    (1) The application, including a table of contents, must:
    (i) Be submitted to the Associate Administrator for Hazardous 
Materials Safety (Attention: General Approvals and Permits, PHH-31), 
Pipeline and Hazardous Materials Safety Administration, U.S. Department 
of Transportation, East Building, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001;
    (ii) Be submitted with any attached supporting documentation by 
facsimile (fax) to: (202) 366-3753 or (202) 366-3308;
    (iii) Be submitted electronically by e-mail to: 
specialpermits@dot.gov; or
    (iv) Be submitted using PHMSA's online system (table of contents 
omitted) at: http://www.phmsa.dot.gov/hazmat/regs/sp-a.
    (2) The application must state the name, mailing address, physical 
address(es) of all known locations where the special permit would be 
used, e-mail address (if available), and telephone number of the 
applicant. If the applicant is not an individual, the application must 
state the company name, mailing address, physical address(es) of all 
known locations where the special permit would be used, e-mail address 
(if available), and telephone number of an individual designated as the 
point of contact for the applicant for all purposes related to the 
application, the name of the company Chief Executive Officer (CEO) or 
president, or ranking officer; and the Dun and Bradstreet Data Universal 
Numbering System (D-U-N-S) identifier.
    (3) If the applicant is not a resident of the United States, in 
addition to the information listed in paragraph (a)(2) of this section, 
the application must identify and designate an agent that is a permanent 
resident of the United States for service in accordance with Sec. 
105.40 of this part.
    (4) For a manufacturing special permit, in addition to the 
information listed in paragraph (a)(2) of this section, the application 
must state the name and street address of each of the facilities of the 
applicant where manufacturing under the special permit will occur, and 
the symbol of the packaging manufacturer (``M'' number), if applicable.
    (5) For persons required to be registered in accordance with Subpart 
F or G of this part, in addition to the information listed in paragraph 
(a)(2) of this section, the application must provide the registration 
number or the

[[Page 23]]

name of the company to which the registration number is assigned if 
different from the applicant. For persons not required to be registered 
in accordance with Subpart F or G of this part, in addition to the 
information listed in paragraph (a)(2) of this section, the application 
must provide a statement indicating that registration is not required.
    (b) Confidential treatment. To request confidential treatment for 
information contained in the application, the applicant must comply with 
Sec. 105.30(a).
    (c) Description of special permit proposal. The application must 
include the following information that is relevant to the special permit 
proposal:
    (1) A citation of the specific regulation from which the applicant 
seeks relief;
    (2) The proposed mode or modes of transportation, including a 
description of all operational controls required;
    (3) A detailed description of the proposed special permit (e.g., 
alternative packaging, test, procedure, activity, or hazard 
communication, including marking and labeling requirements) including, 
as appropriate, written descriptions, drawings, flow charts, plans and 
other supporting documents;
    (4) A specification of the proposed duration or schedule of events 
for which the special permit is sought;
    (5) A statement outlining the applicant's basis for seeking relief 
from compliance with the specified regulations and, if the special 
permit is requested for a fixed period, a description of how compliance 
will be achieved at the end of that period. For transportation by air, a 
statement outlining the reason(s) the hazardous material is being 
transported by air if other modes are available;
    (6) If the applicant seeks emergency processing specified in Sec. 
107.117, a statement of supporting facts and reasons;
    (7) Identification and description, including an estimated quantity 
of each shipment of the hazardous materials planned for transportation 
under the special permit or;
    (8) Description of each packaging, including specification or 
special permit number, as applicable, to be used in conjunction with the 
requested special permit;
    (9) For alternative packagings, documentation of quality assurance 
controls, package design, manufacture, performance test criteria, in-
service performance and service-life limitations;
    (10) An estimate of the number of operations expected to be 
conducted or number of shipments to be transported under the special 
permit;
    (11) An estimate of the number of packagings expected to be 
manufactured under the special permit, if applicable;
    (12) A statement as to whether the special permit being sought is 
related to a compliance review, inspection activity, or enforcement 
action; and
    (13) When a Class 1 material is forbidden for transportation by 
aircraft except under a special permit (see Columns 9A and 9B in the 
table in 49 CFR 172.101), a certification from an applicant for a 
special permit to transport such Class 1 material on passenger-carrying 
or cargo-only aircraft with a maximum certificated takeoff weight of 
less than 12,500 pounds that no person within the categories listed in 
18 U.S.C. 842(i) will participate in the transportation of the Class 1 
material.
    (14) A statement indicating whether the applicant will be acting as 
a shipper (offeror), carrier or both under the terms of the special 
permit.
    (d) Justification of special permit proposal. The application must 
demonstrate that a special permit achieves a level of safety at least 
equal to that required by regulation, or if a required safety level does 
not exist, is consistent with the public interest. At a minimum, the 
application must provide the following:
    (1) Information describing all relevant shipping and incident 
experience of which the applicant is aware that relates to the 
application; and
    (2) A statement identifying any increased risk to safety or property 
that may result if the special permit is granted, and a description of 
the measures to be taken to address that risk; and
    (3) Either:
    (i) Substantiation, with applicable analyses, data or test results 
(e.g., failure mode and effect analysis), that the proposed alternative 
will achieve a

[[Page 24]]

level of safety that is at least equal to that required by the 
regulation from which the special permit is sought; or
    (ii) If the regulations do not establish a level of safety, an 
analysis that identifies each hazard, potential failure mode and the 
probability of its occurrence, and how the risks associated with each 
hazard and failure mode are controlled for the duration of an activity 
or life-cycle of a packaging.

[76 FR 460, Jan. 5, 2011, as amended at 76 FR 44500, July 26, 2011; 76 
FR 43524, July 20, 2011; 76 FR 56310, Sept. 13, 2011]



Sec. 107.107  Application for party status.

    (a) Any person eligible to apply for a special permit may apply to 
be a party to an application or an existing special permit, other than a 
manufacturing special permit.
    (b) Each application filed under this section must conform to the 
following requirements:--
    (1) The application must:
    (i) Be submitted to the Associate Administrator for Hazardous 
Materials Safety (Attention: General Approvals and Permits, PHH-31), 
Pipeline and Hazardous Materials Safety Administration, U.S. Department 
of Transportation, East Building, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001;
    (ii) Be submitted with any attached supporting documentation by 
facsimile (fax) to: (202) 366-3753 or (202) 366-3308; or
    (iii) Be submitted by electronically by e-mail to: 
specialpermits@dot.gov, or on-line at: http://www.phmsa.dot.gov/hazmat/
regs/sp-a.
    (2) The application must identify by number the special permit 
application or special permit to which the applicant seeks to become a 
party.
    (3) The application must state the name, mailing address, physical 
address(es) of all known locations where the special permit would be 
used, e-mail address (if available), and telephone number of the 
applicant. If the applicant is not an individual, the application must 
state the company name, mailing address, physical address(es) of all 
known locations where the special permit would be used, e-mail address 
(if available), and telephone number of an individual designated as the 
point of contact for the applicant for all purposes related to the 
application, the name of the company Chief Executive Officer (CEO), 
president, or ranking executive officer and the Dun and Bradstreet Data 
Universal Numbering System (D-U-N-S) identifier. In addition, each 
applicant must state why party status to the special permit is needed 
and must submit a certification of understanding of the provisions of 
the special permit to which party status is being requested.
    (4) If the applicant is not a resident of the United States, the 
application must identify and designate an agent that is a permanent 
resident of the United States for service in accordance with Sec. 
105.40 of part.
    (5) For a Class 1 material that is forbidden for transportation by 
aircraft except under a special permit (see Columns 9A and 9B in the 
table in 49 CFR 172.101), a certification from an applicant for party 
status to a special permit to transport such Class 1 material on 
passenger-carrying or cargo-only aircraft with a maximum certificated 
takeoff weight of less than 12,500 pounds that no person within the 
categories listed in 18 U.S.C. 842(i) will participate in the 
transportation of the Class 1 material.
    (6) The applicant must certify that the applicant has not previously 
been granted party status to the special permit. If the applicant has 
previously been granted party status, the applicant must follow renewal 
procedures as specified in Sec. 107.109.
    (7) A statement indicating whether the applicant will be acting as a 
shipper (offeror), carrier or both under the terms of the special 
permit.
    (c) The Associate Administrator may grant or deny an application for 
party status in the manner specified in Sec. 107.113(e) and (f) of this 
subpart.
    (d) A party to a special permit is subject to all terms of that 
special permit, including the expiration date. If a party to a special 
permit wishes to renew party status, the special permit renewal 
procedures set forth in Sec. 107.109 apply.

[76 FR 461, Jan. 5, 2011, as amended at 76 FR 44500, July 26, 2011; 76 
FR 43524, July 20, 2011; 76 FR 56310, Sept. 13, 2011]

[[Page 25]]



Sec. 107.109  Application for renewal.

    (a) Each application for renewal of a special permit or party status 
to a special permit must conform to the following requirements:
    (1) The application must:
    (i) Be submitted to the Associate Administrator for Hazardous 
Materials Safety (Attention: General Approvals and Permits, PHH-31), 
Pipeline and Hazardous Materials Safety Administration, U.S. Department 
of Transportation, East Building, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001;
    (ii) Be submitted with any attached supporting documentation 
submitted in an appropriate format by facsimile (fax) to: (202) 366-3753 
or (202) 366-3308; or
    (iii) Be submitted electronically by e-mail to: 
specialpermits@dot.gov; or on-line at: http://www.phmsa.dot.gov/hazmat/
regs/sp-a.
    (2) The application must identify by number the special permit for 
which renewal is requested.
    (3) The application must state the name, mailing address, physical 
address(es) of all known new locations not previously identified in the 
application where the special permit would be used and all locations not 
previously identified where the special permit was used, e-mail address 
(if available), and telephone number of the applicant. If the applicant 
is not an individual, the application must state the name, mailing 
address, physical address(es) of all known new locations not previously 
identified in the application where the special permit would be used and 
all locations not previously identified where the special permit was 
used, e-mail address (if available), and telephone number of an 
individual designated as the point of contact for the applicant for all 
purposes related to the application, the name of the company Chief 
Executive Officer (CEO), president, or ranking executive officer, and 
the Dun and Bradstreet Data Universal Numbering System (D-U-N-S) 
identifier. In addition, each applicant for renewal of party status must 
state why party status to the special permit is needed and must submit a 
certification of understanding of the provisions of the special permit 
to which party status is being requested.
    (4) The application must include either a certification by the 
applicant that the original application, as it may have been updated by 
any application for renewal, remains accurate (e.g., all section 
references, shipping descriptions, etc.) and complete; or include an 
amendment to the previously submitted application as is necessary to 
update and ensure the accuracy and completeness of the application, with 
certification by the applicant that the application as amended is 
accurate and complete.
    (5) The application must include a statement describing all relevant 
operational, shipping, and incident experience of which the applicant is 
aware in connection with the special permit since its issuance or most 
recent renewal. If the applicant is aware of no incidents, the applicant 
must so certify. When known to the applicant, the statement must 
indicate the approximate number of shipments made or packages shipped, 
as applicable, and the number of shipments or packages involved in any 
loss of contents, including loss by venting other than as authorized in 
subchapter C.
    (6) When a Class 1 material is forbidden for transportation by 
aircraft, except under a special permit (see Columns 9A and 9B in the 
table in 49 CFR 172.101), an application to renew a special permit to 
transport such Class 1 material on passenger-carrying or cargo-only 
aircraft with a maximum certificated takeoff weight of less than 12,500 
pounds must certify that no person within the categories listed in 18 
U.S.C. 842(i) will participate in the transportation of the Class 1 
material.
    (7) If the renewal is requested after the expiration date of the 
special permit, the following information is required:
    (i) The reason the special permit authorization was allowed to 
expire;
    (ii) A certification statement that no shipments were transported 
after the expiration date of the special permit, or a statement 
describing any transportation under the terms of the special permit 
after the expiration date, if applicable; and

[[Page 26]]

    (iii) A statement describing the action(s) the applicant will take 
to ensure future renewal is requested before the expiration date.
    (8) If no operations or shipments have been made since the issuance 
or renewal of the special permit, the applicant must provide specific 
justification as to why the special permit should be renewed.
    (9) A statement indicating whether the applicant will be acting as a 
shipper (offeror), carrier or both under the terms of the special 
permit.
    (b) If, at least 60 days before an existing special permit expires 
the holder files an application for renewal that is complete and 
conforms to the requirements of this section, the special permit will 
not expire until final administrative action on the application for 
renewal has been taken.

[76 FR 462, Jan. 5, 2011, as amended at 76 FR 44501, July 26, 2011; 76 
FR 43524, July 20, 2011; 76 FR 56310, Sept. 13, 2011]



Sec. 107.111  Withdrawal.

    An application may be withdrawn at any time before a decision to 
grant or deny it is made. Withdrawal of an application does not 
authorize the removal of any related records from the PHMSA dockets or 
files. Applications that are eligible for confidential treatment under 
Sec. 105.30 will remain confidential after the application is 
withdrawn. The duration of this confidential treatment for trade secrets 
and commercial or financial information is indefinite, unless the party 
requesting the confidential treatment of the materials notifies the 
Associate Administrator that the confidential treatment is no longer 
required.



Sec. 107.113  Application processing and evaluation.

    (a) The Associate Administrator reviews an application for a special 
permit, modification of a special permit, party to a special permit, or 
renewal of a special permit to determine if it is complete and conforms 
with the requirements of this subpart. This determination will be made 
within 30 days of receipt of the application for a special permit, 
modification of a special permit, or party to a special permit, and 
within 15 days of receipt of an application for renewal of a special 
permit. If an application is determined to be incomplete, the applicant 
is informed of the deficiency.
    (b) An application, that is not a renewal, party to, or emergency 
special permit application, and is determined to be complete is 
docketed. Notice of the application is published in the Federal 
Register, and an opportunity for public comment is provided. All 
comments received during the comment period are considered before final 
action is taken on the application.
    (c) No public hearing or other formal proceeding is required under 
this subpart before the disposition of an application. Unless emergency 
processing under Sec. 107.117 is requested and granted, applications 
are usually processed in the order in which they are filed.
    (d) During the processing and evaluation of an application, the 
Associate Administrator may conduct an on-site review or request 
additional information from the applicant. A failure to cooperate with 
an on-site review may result in the application being deemed incomplete 
and subsequently being denied. If the applicant does not respond to a 
written or electronic request for additional information within 30 days 
of the date the request was received, the application may be deemed 
incomplete and denied. However, if the applicant responds in writing or 
by electronic means within the 30-day period requesting an additional 30 
days within which it will gather the requested information, the 
Associate Administrator may grant the 30-day extension.
    (e) The Associate Administrator may grant or deny an application, in 
whole or in part. In the Associate Administrator's discretion, an 
application may be granted subject to provisions that are appropriate to 
protect health, safety or property. The Associate Administrator may 
impose additional provisions not specified in the application or remove 
conditions in the application that are unnecessary.
    (f) The Associate Administrator may grant an application on finding 
that--
    (1) The application complies with this subpart;
    (2) The application demonstrates that the proposed alternative will 
achieve a level of safety that:

[[Page 27]]

    (i) Is at least equal to that required by the regulation from which 
the special permit is sought, or
    (ii) If the regulations do not establish a level of safety, is 
consistent with the public interest and adequately will protect against 
the risks to life and property inherent in the transportation of 
hazardous materials in commerce;
    (3) The application states all material facts, and contains no 
materially false or materially misleading statement;
    (4) The applicant meets the qualifications required by applicable 
regulations; and
    (5) The applicant is fit to conduct the activity authorized by the 
special permit. This assessment may be based on information in the 
application, prior compliance history of the applicant, and other 
information available to the Associate Administrator.
    (g) An applicant is notified in writing or by electronic means 
whether the application is granted or denied. A denial contains a brief 
statement of reasons.
    (h) The initial special permit terminates according to its terms or, 
if not otherwise specified, 24 months from the date of issuance. A 
subsequent renewal of a special permit terminates according to its terms 
or, if not otherwise specified, 48 months after the date of issuance. A 
grant of party status to a special permit, unless otherwise stated, 
terminates on the date that the special permit expires.
    (i) The Associate Administrator, on determining that an application 
concerns a matter of general applicability and future effect and should 
be the subject of rulemaking, may initiate rulemaking under part 106 of 
this chapter in addition to or instead of acting on the application.
    (j) The Associate Administrator publishes in the Federal Register a 
list of all special permit grants, denials, and modifications and all 
special permit applications withdrawn under this section.

[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 67 FR 61011, 
Sept. 27, 2002; 70 FR 73161, Dec. 9, 2005; 76 FR 463, Jan. 5, 2011]



Sec. 107.117  Emergency processing.

    (a) An application is granted emergency processing if the Associate 
Administrator, on the basis of the application and any inquiry 
undertaken, finds that--
    (1) Emergency processing is necessary to prevent significant injury 
to persons or property (other than the hazardous material to be 
transported) that could not be prevented if the application were 
processed on a routine basis; or
    (2) Emergency processing is necessary for immediate national 
security purposes or to prevent significant economic loss that could not 
be prevented if the application were processed on a routine basis.
    (b) Where the significant economic loss is to the applicant, or to a 
party in a contractual relationship to the applicant with respect to the 
activity to be undertaken, the Associate Administrator may deny 
emergency processing if timely application could have been made.
    (c) A request for emergency processing on the basis of potential 
economic loss must reasonably describe and estimate the potential loss.
    (d) An application submitted under this section must conform to 
Sec. 107.105 to the extent that the receiving Department official deems 
necessary to process the application. An application on an emergency 
basis must be submitted to the Department modal contact official for the 
initial mode of transportation to be utilized, as follows:
    (1) Certificate-Holding Aircraft: The Federal Aviation 
Administration Civil Aviation Security Office that serves the place 
where the flight will originate or that is responsible for the aircraft 
operator's overall aviation security program. The nearest Civil Aviation 
Security Office may be located by calling the FAA Duty Officer, 202-267-
3333 (any hour).
    (2) Noncertificate-Holding Aircraft (Those Which Operate Under 14 
CFR Part 91): The Federal Aviation Administration Civil Aviation 
Security Office that serves the place where the flight will originate. 
The nearest Civil Aviation Security Office may be located by calling the 
FAA Duty Officer, 202-267-3333 (any hour).
    (3) Motor Vehicle Transportation: Chief, Hazardous Materials 
Division,

[[Page 28]]

Federal Motor Carrier Safety Administration, U.S. Department of 
Transportation, Washington, DC 20590-0001, 202-385-2400 (day); 1-800-
424-8802 (night).
    (4) Rail Transportation: Staff Director, Hazardous Materials 
Division, Office of Safety Assurance and Compliance, Federal Railroad 
Administration, U.S. Department of Transportation, Washington, DC 20590-
0001, 202-493-6248 or 202-493-6244 (day); 1-800-424-8802 (night).
    (5) Water Transportation: Chief, Hazardous Materials Standards 
Division, Office of Operating and Environmental Standards, U.S. Coast 
Guard, U.S. Department of Homeland Security, Washington, DC 20593-0001; 
202-372-1420 (day); 1-800-424-8802 (night).
    (e) On receipt of all information necessary to process the 
application, the receiving Department official transmits to the 
Associate Administrator, by the most rapid available means of 
communication, an evaluation as to whether an emergency exists under 
Sec. 107.117(a) and, if appropriate, recommendations as to the 
conditions to be included in the special permit. If the Associate 
Administrator determines that an emergency exists under Sec. 107.117(a) 
and that, with reference to the criteria of Sec. 107.113(f), granting 
of the application is in the public interest, the Associate 
Administrator grants the application subject to such terms as necessary 
and immediately notifies the applicant. If the Associate Administrator 
determines that an emergency does not exist or that granting of the 
application is not in the public interest, the applicant immediately is 
so notified.
    (f) A determination that an emergency does not exist is not subject 
to reconsideration under Sec. 107.123 of this part.
    (g) Within 90 days following issuance of an emergency special 
permit, the Associate Administrator will publish, in the Federal 
Register, a notice of issuance with a statement of the basis for the 
finding of emergency and the scope and duration of the special permit.

[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 62 FR 51556, Oct. 
1, 1997; 64 FR 51914, Sept. 27, 1999; 65 FR 58618, Sept. 29, 2000; 66 FR 
45377, Aug. 28, 2001; 67 FR 61011, Sept. 27, 2002; 70 FR 56090, Sept. 
23, 2005; 75 FR 53596, Sept. 1, 2010; 76 FR 463, Jan. 5, 2011]



Sec. 107.121  Modification, suspension or termination of special permit or 

grant of party status.

    (a) The Associate Administrator may modify a special permit or grant 
of party status on finding that:
    (1) Modification is necessary so that the special permit reflects 
current statutes and regulations; or
    (2) Modification is required by changed circumstances to meet the 
standards of Sec. 107.113(f).
    (b) The Associate Administrator may modify, suspend or terminate a 
special permit or grant of party status, as appropriate, on finding 
that:
    (1) Because of a change in circumstances, the special permit or 
party status no longer is needed or no longer would be granted if 
applied for;
    (2) The application contained inaccurate or incomplete information, 
and the special permit or party status would not have been granted had 
the application been accurate and complete;
    (3) The application contained deliberately inaccurate or incomplete 
information; or
    (4) The holder or party knowingly has violated the terms of the 
special permit or an applicable requirement of this chapter in a manner 
demonstrating the holder or party is not fit to conduct the activity 
authorized by the special permit.
    (c) Except as provided in paragraph (d) of this section, before a 
special permit or grant of party status is modified, suspended, or 
terminated, the Associate Administrator notifies the holder or party in 
writing or by electronic means of the proposed action and the reasons 
for it, and provides an opportunity to show cause why the proposed 
action should not be taken.
    (1) Within 30 days of receipt of notice of the proposed action, the 
holder or party may file a response in writing or by electronic means 
that shows cause

[[Page 29]]

why the proposed action should not be taken.
    (2) After considering the holder's or party's response, or after 30 
days have passed without response since receipt of the notice, the 
Associate Administrator notifies the holder or party in writing or by 
electronic means of the final decision with a brief statement of 
reasons.
    (d) The Associate Administrator, if necessary to avoid a risk of 
significant harm to persons or property, may, in the notification, 
declare the proposed action immediately effective.

[76 FR 463, Jan. 5, 2011]



Sec. 107.123  Reconsideration.

    (a) An applicant for special permit, a special permit holder, or an 
applicant for party status to a special permit may request that the 
Associate Administrator reconsider a decision under Sec. 107.113(g), 
Sec. 107.117(e) or Sec. 107.121(c) of this part. The request must--
    (1) Be in writing or by electronic means and filed within 20 days of 
receipt of the decision;
    (2) State in detail any alleged errors of fact and law;
    (3) Enclose any additional information needed to support the request 
to reconsider; and
    (4) State in detail the modification of the final decision sought.
    (b) The Associate Administrator grants or denies, in whole or in 
part, the relief requested and informs the requesting person in writing 
or by electronic means of the decision. If necessary to avoid a risk of 
significant harm to persons or property, the Associate Administrator 
may, in the notification, declare the action immediately effective.

[76 FR 463, Jan. 5, 2011]



Sec. 107.125  Appeal.

    (a) A person who requested reconsideration under Sec. 107.123 and 
is denied the relief requested may appeal to the Administrator. The 
appeal must--
    (1) Be in writing or by electronic means and filed within 30 days of 
receipt of the Associate Administrator's decision on reconsideration; 
(2) state in detail any alleged errors of fact and law;
    (2) State in detail any alleged errors of fact and law;
    (3) Enclose any additional information needed to support the appeal; 
and
    (4) State in detail the modification of the final decision sought.
    (b) The Administrator, if necessary to avoid a risk of significant 
harm to persons or property, may declare the Associate Administrator's 
action effective pending a decision on appeal.
    (c) The Administrator grants or denies, in whole or in part, the 
relief requested and informs the appellant in writing or by electronic 
means of the decision. The Administrator's decision is the final 
administrative action.

[ Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 76 FR 463, Jan. 
5, 2011]



Sec. 107.127  Availability of documents for public inspection.

    (a) Documents related to an application under this subpart, 
including the application itself, are available for public inspection, 
except as specified in paragraph (b) of this section, at the Office of 
the Associate Administrator for Hazardous Materials Safety, Pipeline and 
Hazardous Materials Safety Administration, Approvals and Permits 
Division, U.S. Department of Transportation, East Building, PHH-30, 1200 
New Jersey Avenue, SE., Washington, DC 20590-0001. Office hours are 8:30 
a.m. to 5 p.m., Monday through Friday, except Federal holidays when the 
office is closed. Copies of available documents may be obtained as 
provided in part 7 of this title. Documents numbered 11832 and above may 
also be viewed at the website address http://www.regulations.gov.
    (b) Documents available for inspection do not include materials 
determined to be withheld from public disclosure under Sec. 105.30 and 
in accordance with the applicable provisions of section 552(b) of title 
5, United States Code, and part 7 of this title.

[Amdt. 107-38, 61 FR 21095, May 9, 1996, as amended at 65 FR 58618, 
Sept. 29, 2000; 66 FR 45377, Aug. 28, 2001; 67 FR 61011, Sept. 27, 2002; 
70 FR 73162, Dec. 9, 2005; 72 FR 55683, Oct. 1, 2007; 76 FR 56310, Sept. 
13, 2011]

[[Page 30]]



                          Subpart C_Preemption



Sec. 107.201  Purpose and scope.

    (a) This subpart prescribes procedures by which:
    (1) Any person, including a State, political subdivision, or Indian 
tribe, directly affected by a requirement of a State, political 
subdivision, or Indian tribe, may apply for a determination as to 
whether that requirement is preempted under 49 U.S.C. 5125.
    (2) A State, political subdivision, or Indian tribe may apply for a 
waiver of preemption with respect to any requirement that the State, 
political subdivision, or Indian tribe acknowledges to be preempted by 
49 U.S.C. 5125, or that has been determined by a court of competent 
jurisdiction to be so preempted.
    (b) For purposes of this subpart ``political subdivision'' includes 
a municipality; a public agency or other instrumentality of one or more 
States, municipalities, or other political subdivisions of a State; or a 
public corporation, board, or commission established under the laws of 
one or more States.
    (c) [Reserved]
    (d) An application for a preemption determination that includes an 
application for a waiver of preemption will be treated and processed 
solely as an application for a preemption determination.

[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56 
FR 8622, Feb. 28, 1991; Amdt. 107-25, 57 FR 20428, May 13, 1992; Amdt. 
107-32, 59 FR 49130, Sept. 26, 1994; Amdt. 107-35, 60 FR 49108, Sept. 
21, 1995; Amdt. 107-38, 61 FR 21098, May 9, 1996; 68 FR 52846, Sept. 8, 
2003; 71 FR 30067, May 25, 2006]



Sec. 107.202  Standards for determining preemption.

    (a) Except as provided in Sec. 107.221 and unless otherwise 
authorized by Federal law, any requirement of a State or political 
subdivision thereof or an Indian tribe that concerns one of the 
following subjects and that is not substantively the same as any 
provision of the Federal hazardous materials transportation law, a 
regulation issued under the Federal hazardous material transportation 
law, or a hazardous material transportation security regulation or 
directive issued by the Secretary of Homeland Security that concerns 
that subject, is preempted:
    (1) The designation, description, and classification of hazardous 
material.
    (2) The packing, repacking, handling, labeling, marking, and 
placarding of hazardous material.
    (3) The preparation, execution, and use of shipping documents 
pertaining to hazardous material and requirements related to the number, 
content, and placement of those documents.
    (4) The written notification, recording, and reporting of the 
unintentional release in transportation of hazardous material.
    (5) The design, manufacturing, fabrication, marking, maintenance, 
reconditioning, repairing, or testing of a packaging or a container 
which is represented, marked, certified, or sold as qualified for use in 
the transportation of hazardous material.
    (b) Except as provided in Sec. 107.221 and unless otherwise 
authorized by Federal law, any requirement of a State or political 
subdivision or Indian tribe is preempted if--
    (1) It is not possible to comply with a requirement of the State, 
political subdivision, or Indian tribe and a requirement under the 
Federal hazardous material transportation law, a regulation issued under 
the Federal hazardous material transportation law, or a hazardous 
material transportation security regulation or directive issued by the 
Secretary of Homeland Security;
    (2) The requirement of the State, political subdivision, or Indian 
tribe, as applied or enforced, is an obstacle to accomplishing and 
carrying out the Federal hazardous material transportation law, a 
regulation issued under the Federal hazardous material transportation 
law, or a hazardous material transportation security regulation or 
directive issued by the Secretary of Homeland Security.
    (3) It is preempted under 49 U.S.C. 5125 (c).
    (c) A State, political subdivision, or Indian tribe may impose a fee 
related to transporting hazardous material only if the fee is fair and 
used for a purpose related to transporting hazardous material, including 
enforcement and planning, developing and

[[Page 31]]

maintaining a capability for emergency response.
    (d) For purposes of this section, ``substantively the same'' means 
that the non-Federal requirement conforms in every significant respect 
to the Federal requirement. Editorial and other similar de minimis 
changes are permitted.

[Amdt. 107-24, 56 FR 8622, Feb. 28, 1991, as amended by Amdt. 107-25, 57 
FR 20428, May 13, 1992; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; Amdt. 
107-32, 59 FR 49130, Sept. 26, 1994; Amdt. 107-38, 61 FR 21098, May 9, 
1996; Amdt. 107-39, 61 FR 51337, Oct. 1, 1996; 68 FR 52847, Sept. 8, 
2003]

                        Preemption Determinations



Sec. 107.203  Application.

    (a) With the exception of highway routing matters covered under 49 
U.S.C. 5125(c), any person, including a State or political subdivision 
thereof or an Indian tribe, directly affected by any requirement of a 
State or political subdivision thereof or an Indian tribe, may apply to 
the Chief Counsel for a determination as to whether that requirement is 
preempted by Sec. 107.202(a), (b), or (c).
    (b) Each application filed under this section for a determination 
must:
    (1) Be submitted to the Chief Counsel:
    (i) By mail addressed to the Chief Counsel, Pipeline and Hazardous 
Materials Safety Administration, U.S. Department of Transportation, East 
Building, PHC-1, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001;
    (ii) By facsimile to 202-366-7041; or
    (iii) Electronically to the Chief Counsel at 
phmsachiefcounsel@dot.gov.
    (2) Set forth the text of the State or political subdivision or 
Indian tribe requirement for which the determination is sought;
    (3) Specify each requirement of the Federal hazardous materials 
transportation law, regulations issued under the Federal hazardous 
material transportation law, or hazardous material transportation 
security regulations or directives issued by the Secretary of Homeland 
Security with which the applicant seeks the State or political 
subdivision or Indian tribe requirement to be compared;
    (4) Explain why the applicant believes the State or political 
subdivision or Indian tribe requirement should or should not be 
preempted under the standards of Sec. 107.202; and
    (5) State how the applicant is affected by the State or political 
subdivision or Indian tribe requirement.
    (c) The filing of an application for a determination under this 
section does not constitute grounds for noncompliance with any 
requirement of the Federal hazardous materials transportation law, 
regulations issued under the Federal hazardous material transportation 
law, or hazardous material transportation security regulations or 
directives issued by the Secretary of Homeland Security.
    (d) Once the Chief Counsel has published notice in the Federal 
Register of an application received under paragraph (a) of this section, 
no applicant for such determination may seek relief with respect to the 
same or substantially the same issue in any court until final action has 
been taken on the application or until 180 days after filing of the 
application, whichever occurs first. Nothing in Sec. 107.203(a) 
prohibits a State or political subdivision thereof or Indian tribe, or 
any other person directly affected by any requirement of a State or 
political subdivision thereof or Indian tribe, from seeking a 
determination of preemption in any court of competent jurisdiction in 
lieu of applying to the Chief Counsel under paragraph (a) of this 
section.

[Amdt. 107-24, 56 FR 8622, Feb. 28, 1991, as amended by Amdt. 107-25, 57 
FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 
107-38, 61 FR 21098, May 9, 1996; 68 FR 52847, Sept. 8, 2003; 71 FR 
30067, May 25, 2006; 72 FR 55683, Oct. 1, 2007]



Sec. 107.205  Notice.

    (a) If the applicant is other than a State, political subdivision, 
or Indian tribe, the applicant shall mail a copy of the application to 
the State, political subdivision, or Indian tribe concerned accompanied 
by a statement that the State, political subdivision, or Indian tribe 
may submit comments regarding the application to the Chief Counsel. The 
application filed with the Chief Counsel must include a certification 
that the applicant has complied with

[[Page 32]]

this paragraph and must include the names and addresses of each State, 
political subdivision, or Indian tribe official to whom a copy of the 
application was sent.
    (b) The Chief Counsel will publish notice of, including an 
opportunity to comment on, an application in the Federal Register and 
may notify in writing any person readily identifiable as affected by the 
outcome of the determination.
    (c) Each person submitting written comments to the Chief Counsel 
with respect to an application filed under this section must send a copy 
of the comments to the applicant and certify to the Chief Counsel that 
he or she has complied with this requirement. The Chief Counsel may 
notify other persons participating in the proceeding of the comments and 
provide an opportunity for those other persons to respond. Late-filed 
comments are considered so far as practicable.

[Amdt. 107-38, 61 FR 21098, May 9, 1996, as amended at 71 FR 30067, May 
25, 2006]



Sec. 107.207  Processing.

    (a) The Chief Counsel may initiate an investigation of any statement 
in an application and utilize in his or her evaluation any relevant 
facts obtained by that investigation. The Chief Counsel may solicit and 
accept submissions from third persons relevant to an application and 
will provide the applicant an opportunity to respond to all third person 
submissions. In evaluating an application, the Chief Counsel may 
consider any other source of information. The Chief Counsel on his or 
her own initiative may convene a hearing or conference, if he or she 
considers that a hearing or conference will advance his or her 
evaluation of the application.
    (b) The Chief Counsel may dismiss the application without prejudice 
if:
    (1) He or she determines that there is insufficient information upon 
which to base a determination; or
    (2) He or she requests additional information from the applicant and 
it is not submitted.

[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56 
FR 8621, 8622, Feb. 28, 1991; Amdt. 107-38, 61 FR 21098, May 9, 1996; 71 
FR 30067, May 25, 2006]



Sec. 107.209  Determination.

    (a) Upon consideration of the application and other relevant 
information received, the Chief Counsel issues a determination.
    (b) The determination includes a written statement setting forth the 
relevant facts and the legal basis for the determination, and provides 
that any person aggrieved thereby may file a petition for 
reconsideration with the Chief Counsel.
    (c) The Chief Counsel provides a copy of the determination to the 
applicant and to any other person who substantially participated in the 
proceeding or requested in comments to the docket to be notified of the 
determination. A copy of each determination is placed on file in the 
public docket. The Chief Counsel will publish the determination or 
notice of the determination in the Federal Register, at which time the 
determination becomes a final agency action.
    (d) A determination issued under this section constitutes an 
administrative determination as to whether a particular requirement of a 
State or political subdivision or Indian tribe is preempted under the 
Federal hazardous materials transportation law. The fact that a 
determination has not been issued under this section with respect to a 
particular requirement of a State or political subdivision or Indian 
tribe carries no implication as to whether the requirement is preempted 
under the Federal hazardous materials transportation law.

[Amdt. 107-24, 56 FR 8623, Feb. 28, 1991, as amended by Amdt. 107-25, 57 
FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 
107-38, 61 FR 21098, May 9, 1996; 68 FR 52847, Sept. 8, 2003; 71 FR 
30067, May 25, 2006]



Sec. 107.211  Petition for reconsideration.

    (a) Any person aggrieved by a determination issued under Sec. 
107.209 may file a petition for reconsideration. The petition must be 
filed with the Chief Counsel, in the same manner specified for filing an 
application in Sec. 107.203(b), within 20 days of publication of the 
determination in the Federal Register.
    (b) The petition must contain a concise statement of the basis for 
seeking review, including any specific factual

[[Page 33]]

or legal error alleged. If the petition requests consideration of 
information that was not previously made available to the Chief Counsel, 
the petition must include the reasons why such information was not 
previously made available.
    (c) The petitioner shall mail a copy of the petition to each person 
who participated, either as an applicant or commenter, in the preemption 
determination proceeding, accompanied by a statement that the person may 
submit comments concerning the petition to the Chief Counsel within 20 
days. The petition filed with the Chief Counsel must contain a 
certification that the petitioner has complied with this paragraph and 
include the names and addresses of all persons to whom a copy of the 
petition was sent. Late-filed comments are considered so far as 
practicable.
    (d) The Chief Counsel will publish the decision on the petition for 
reconsideration or notice of the decision in the Federal Register, at 
which time the decision on the petition for reconsideration becomes a 
final agency action.

[Amdt. 107-25, 57 FR 20428, May 13, 1992, as amended by Amdt. 107-38, 61 
FR 21099, May 9, 1996; 71 FR 30067, May 25, 2006]



Sec. 107.213  Judicial review.

    A party to a proceeding under Sec. 107.203(a) may seek review of a 
determination of the Chief Counsel by filing a petition, within 60 days 
after the determination becomes final, in the United States Court of 
Appeals for the District of Columbia or in the Court of Appeals for the 
United States for the circuit in which the person resides or has its 
principal place of business.

[71 FR 30068, May 25, 2006]

                   Waiver of Preemption Determinations



Sec. 107.215  Application.

    (a) With the exception of requirements preempted under 49 U.S.C. 
5125(c), a State or political subdivision thereof, or Indian tribe may 
apply to the Chief Counsel for a waiver of preemption with respect to 
any requirement that the State or political subdivision thereof or 
Indian tribe acknowledges to be preempted under the Federal hazardous 
materials transportation law, or that has been determined by a court of 
competent jurisdiction to be so preempted. The Chief Counsel may waive 
preemption with respect to such requirement upon a determination that 
such requirement--
    (1) Affords an equal or greater level of protection to the public 
than is afforded by the requirements of the Federal hazardous material 
transportation law or the regulations issued thereunder, and
    (2) Does not unreasonably burden commerce.
    (b) Each application filed under this section for a waiver of 
preemption determination must:
    (1) Be submitted to the Chief Counsel:
    (i) By mail addressed to the Chief Counsel, Pipeline and Hazardous 
Materials Safety Administration, U.S. Department of Transportation, East 
Building, PHC-1, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001;
    (ii) By facsimile to 202-366-7041; or
    (iii) Electronically to the Chief Counsel at 
phmsachiefcounsel@dot.gov.
    (2) Set forth the text of the State or political subdivision 
requirement for which the determination is being sought;
    (3) Include a copy of any court order and any ruling issued under 
Sec. 107.209 having a bearing on the application;
    (4) Contain an express acknowledgment by the applicant that the 
State, political subdivision, or Indian tribe requirement is preempted 
under Federal hazardous materials transportation law, unless it has been 
so determined by a court of competent jurisdiction or in a determination 
issued under Sec. 107.209;
    (5) Specify each requirement of the Federal hazardous materials 
transportation law that preempts the State, political subdivision, or 
Indian tribe requirement;
    (6) State why the applicant believes the State, political 
subdivision or Indian tribe requirements affords an equal or greater 
level of protection to the public than is afforded by the requirements 
of the Federal hazardous material transportation law or the regulations 
issued thereunder;

[[Page 34]]

    (7) State why the applicant believes the State, political 
subdivision or Indian tribe requirement does not unreasonably burden 
commerce; and
    (8) Specify what steps the State, political subdivision or Indian 
tribe is taking to administer and enforce effectively its inconsistent 
requirement.

[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-22, 55 
FR 39978, Oct. 1, 1990; Amdt. 107-24, 56 FR 8621, 8623, Feb. 28, 1991; 
56 FR 15510, Apr. 17, 1991; Amdt. 107-23, 56 FR 66156, Dec. 20, 1991; 
Amdt. 107-25, 57 FR 20428, May 13, 1992; Amdt. 107-32, 59 FR 49131, 
Sept. 26, 1994; Amdt. 107-38, 61 FR 21099, May 9, 1996; 68 FR 52847, 
Sept. 8, 2003; 71 FR 30068, May 25, 2006; 72 FR 55683, Oct. 1, 2007]



Sec. 107.217  Notice.

    (a) The applicant shall mail a copy of the application and any 
subsequent amendments or other documents relating to the application to 
each person who is reasonably ascertainable by the applicant as a person 
who will be affected by the determination sought. The copy of the 
application must be accompanied by a statement that the person may 
submit comments regarding the application within 45 days. The 
application must include a certification that the application has 
complied with this paragraph and must include the names and addresses of 
each person to whom the application was sent.
    (b) Notwithstanding the provisions of paragraph (a) of this section, 
if the State or political subdivision determines that compliance with 
paragraph (a) of this section would be impracticable, the applicant 
shall:
    (1) Comply with the requirements of paragraph (a) of this section 
with regard to those persons whom it is reasonable and practicable to 
notify; and
    (2) Include with the application a description of the persons or 
class or classes of persons to whom notice was not sent.
    (c) The Chief Counsel may require the applicant to provide notice in 
addition to that required by paragraphs (a) and (b) of this section, or 
may determine that the notice required by paragraph (a) of the section 
is not impracticable, or that notice should be published in the Federal 
Register. Late-filed comments are considered so far as practicable.
    (d) The Chief Counsel may notify any other persons who may be 
affected by the outcome of a determination on the application.
    (e) Any person submitting written comments with respect to an 
application filed under this section shall send a copy of the comments 
to the applicant. The person shall certify that he has complied with the 
requirements of this paragraph. The Chief Counsel may notify other 
persons participating in the proceeding of the comments and provide an 
opportunity for those other persons to respond.

[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56 
FR 8621, Feb. 28, 1991; Amdt. 107-25, 57 FR 20429, May 13, 1992; Amdt. 
107-38, 61 FR 21099, May 9, 1996; 71 FR 30068, May 25, 2006]



Sec. 107.219  Processing.

    (a) The Chief Counsel may initiate an investigation of any statement 
in an application and utilize in his or her evaluation any relevant 
facts obtained by that investigation. The Chief Counsel may solicit and 
accept submissions from third persons relevant to an application and 
will provide the applicant an opportunity to respond to all third person 
submissions. In evaluating an application, the Chief Counsel on his or 
her own initiative may convene a hearing or conference, if he or she 
considers that a hearing or conference will advance his or her 
evaluation of the application.
    (b) The Chief Counsel may dismiss the application without prejudice 
if:
    (1) He or she determines that there is insufficient information upon 
which to base a determination;
    (2) Upon his or her request, additional information is not submitted 
by the applicant; or
    (3) The applicant fails to provide the notice required by Sec. 
107.217.
    (c) The Chief Counsel will only consider an application for waiver 
of preemption determination if--
    (1) The applicant State or political subdivision thereof or Indian 
tribe expressly acknowledges in its application that the State or 
political subdivision or Indian tribe requirement for which the 
determination is sought is inconsistent with the requirements of the

[[Page 35]]

Federal hazardous materials transportation law, regulations issued under 
the Federal hazardous material transportation law, or hazardous material 
transportation security regulations or directives issued by the 
Secretary of Homeland Security.
    (2) The State or political subdivision thereof or Indian tribe 
requirement has been determined by a court of competent jurisdiction or 
in a ruling issued under Sec. 107.209 to be inconsistent with the 
requirements of the Federal hazardous materials transportation law, 
regulations issued under the Federal hazardous material transportation 
law, or hazardous material transportation security regulations or 
directives issued by the Secretary of Homeland Security.
    (d) When the Chief Counsel has received all substantive information 
it considers necessary to process an application for a waiver of 
preemption determination, it serves notice of that fact upon the 
applicant and all other persons who received notice of the proceeding 
pursuant to Sec. 107.217.
    (e) To the extent possible, each application for a waiver of 
preemption determination will be acted upon in a manner consistent with 
the disposition of previous applications for waiver of preemption 
determinations.

[Amdt. 107-3, 41 FR 38171, Sept. 9, 1976, as amended by Amdt. 107-24, 56 
FR 8621, 8623, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; 
Amdt. 107-38, 61 FR 21099, May 9, 1996; 65 FR 58618, Sept. 29, 2000; 68 
FR 52847, Sept. 8, 2003; 69 FR 54044, Sept. 7, 2004; 71 FR 30068, May 
25, 2006]



Sec. 107.221  Determination.

    (a) After considering the application and other relevant information 
received or obtained during the proceeding, the Chief Counsel issues a 
determination.
    (b) The Chief Counsel may issue a waiver of preemption only on 
finding that the requirement of the State or political subdivision 
thereof or Indian tribe affords the public a level of safety at least 
equal to that afforded by the requirements of the Federal hazardous 
material transportation law or the regulations issued thereunder and 
does not unreasonably burden commerce. In determining if the requirement 
of the State or political subdivision thereof or Indian tribe 
unreasonably burdens commerce, the Chief Counsel considers:
    (1) The extent to which increased costs and impairment of efficiency 
result from the requirement of the State or political subdivision 
thereof or Indian tribe.
    (2) Whether the requirement of the State or political subdivision 
thereof or Indian tribe has a rational basis.
    (3) Whether the requirement of the State or political subdivision 
thereof or Indian tribe achieves its stated purpose.
    (4) Whether there is need for uniformity with regard to the subject 
concerned and if so, whether the requirement of the State or political 
subdivision thereof or Indian tribe competes or conflicts with those of 
other States or political subdivisions thereof or Indian tribes.
    (c) The determination includes a written statement setting forth 
relevant facts and legal bases and providing that any person aggrieved 
by the determination may file a petition for reconsideration with the 
Chief Counsel.
    (d) The Chief Counsel provides a copy of the determination to the 
applicant and to any other person who substantially participated in the 
proceeding or requested in comments to the docket to be notified of the 
determination. A copy of the determination is placed on file in the 
public docket. The Chief Counsel will publish the determination or 
notice of the determination in the Federal Register, at which time the 
determination becomes a final agency action.
    (e) A determination under this section constitutes an administrative 
finding of whether a particular requirement of a State or political 
subdivision thereof or Indian tribe is preempted under the Federal 
hazardous materials transportation law, or whether preemption is waived.

[Amdt. 107-38, 61 FR 21099, May 9, 1996, as amended at 68 FR 52848, 
Sept. 8, 2003; 71 FR 30068, May 25, 2006]



Sec. 107.223  Petition for reconsideration.

    (a) Any person aggrieved by a determination under Sec. 107.221 may 
file a petition for reconsideration. The petition

[[Page 36]]

must be filed with the Chief Counsel, in the same manner specified for 
filing an application in Sec. 107.215(b), within 20 days of publication 
of the determination in the Federal Register.
    (b) The petition must contain a concise statement of the basis for 
seeking review, including any specific factual or legal error alleged. 
If the petition requests consideration of information that was not 
previously made available to the Chief Counsel, the petition must 
include the reasons why such information was not previously made 
available.
    (c) The petitioner shall mail a copy of the petition to each person 
who participated, either as an applicant or commenter, in the waiver of 
preemption proceeding, accompanied by a statement that the person may 
submit comments concerning the petition to the Chief Counsel within 20 
days. The petition filed with the Chief Counsel must contain a 
certification that the petitioner has complied with this paragraph and 
include the names and addresses of all persons to whom a copy of the 
petition was sent. Late-filed comments are considered so far as 
practicable.
    (d) The Chief Counsel will publish the decision on the petition for 
reconsideration or notice of the decision in the Federal Register, at 
which time the decision on the petition for reconsideration becomes a 
final agency action.

[Amdt. 107-25, 57 FR 20429, May 13, 1992, as amended by Amdt. 107-38, 61 
FR 21099, May 9, 1996; 71 FR 30068, May 25, 2006]



Sec. 107.227  Judicial review.

    A party to a proceeding under Sec. 107.215(a) may seek review of a 
determination of the Chief Counsel by filing a petition, within 60 days 
after the determination becomes final, in the United States Court of 
Appeals for the District of Columbia or in the Court of Appeals for the 
United States for the circuit in which the person resides or has its 
principal place of business.

[71 FR 30068, May 25, 2006]



                          Subpart D_Enforcement

    Source: Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, unless otherwise 
noted.



Sec. 107.301  Delegated authority for enforcement.

    Under redelegation from the Administrator, Pipeline and Hazardous 
Materials Safety Administration, the Associate Administrator for 
Hazardous Materials Safety and the Office of the Chief Counsel exercise 
their authority for enforcement of the Federal hazardous material 
transportation law, this subchapter, and subchapter C of this 
subchapter, in accordance with Sec. 1.53 of this title.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-24, 56 
FR 8621, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994]



Sec. 107.303  Purpose and scope.

    This subchapter describes the various enforcement authorities 
exercised by the Associate Administrator for Hazardous Materials Safety 
and the Office of Chief Counsel and the associated sanctions and 
prescribes the procedures governing the exercise of those authorities 
and the imposition of those sanctions.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51 
FR 34986, Oct. 1, 1986; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991]



Sec. 107.305  Investigations.

    (a) General. In accordance with its delegated authority under part 1 
of this title, the Associate Administrator may initiate investigations 
relating to compliance by any person with any provisions of this 
subchapter or subchapter C of this chapter, or any special permit, 
approval, or order issued thereunder, or any court decree relating 
thereto. The Associate Administrator encourages voluntary production of 
documents in accordance with and subject to Sec. 105.45, and hearings 
may be conducted, and depositions taken pursuant to 49 U.S.C. 5121(a). 
The Associate Administrator may conduct investigative conferences and 
hearings in the course of any investigation.
    (b) Investigations and Inspections. Investigations under 49 U.S.C. 
5121(a) are conducted by personnel duly authorized for that purpose by 
the Associate Administrator. Inspections under 49

[[Page 37]]

U.S.C. 5121(c) are conducted by Hazardous Materials Enforcement 
Specialists or Hazardous Materials Compliance Investigators, also known 
as ``hazmat investigators'' or ``investigators,'' whom the Associate 
Administrator has designated for that purpose.
    (1) An investigator will, on request, present his or her credentials 
for examination, but the credentials may not be reproduced.
    (2) An investigator may administer oaths and receive affirmations in 
any matter under investigation by the Associate Administrator.
    (3) An investigator may gather information by reasonable means 
including, but not limited to, interviews, statements, photocopying, 
photography, and video- and audio-recording.
    (4) With concurrence of the Director, Field Operations, Pipeline and 
Hazardous Materials Safety Administration, an investigator may issue a 
subpoena for the production of documentary or other tangible evidence 
if, on the basis of information available to the investigator, the 
documents and evidence materially will advance a determination of 
compliance with this subchapter or subchapter C. Service of a subpoena 
shall be in accordance with Sec. 105.50. A person to whom a subpoena is 
directed may seek review of the subpoena by applying to the Office of 
Chief Counsel in accordance with Sec. 105.55(a). A subpoena issued 
under this paragraph may be enforced in accordance with Sec. 105.55(b).
    (c) Notification. Any person who is the subject of an Associate 
Administrator investigation and who is requested to furnish information 
or documentary evidence is notified as to the general purpose for which 
the information or evidence is sought.
    (d) Termination. When the facts disclosed by an investigation 
indicate that further action is unnecessary or unwarranted at that time, 
the person being investigated is notified and the investigative file is 
closed without prejudice to further investigation by the Associate 
Administrator.
    (e) Confidentiality. Information received in an investigation under 
this section, including the identity of the person investigated and any 
other person who provides information during the investigation, shall 
remain confidential under the investigatory file exception, or other 
appropriate exception, to the public disclosure requirements of 5 U.S.C. 
552.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-24, 56 
FR 8621, Feb. 28, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 
107-38, 61 FR 21099, May 9, 1996; 66 FR 45377, Aug. 28, 2001; 67 FR 
61011, Sept. 27, 2002; 73 FR 4711, Jan. 28, 2008; 76 FR 56311, Sept. 13, 
2011]

                  Compliance Orders and Civil Penalties



Sec. 107.307  General.

    (a) When the Associate Administrator and the Office of Chief Counsel 
have reason to believe that a person is knowingly engaging or has 
knowingly engaged in conduct which is a violation of the Federal 
hazardous material transportation law or any provision of this 
subchapter or subchapter C of this chapter, or any exemption, special 
permit, or order issued thereunder, for which the Associate 
Administrator or the Office of Chief Counsel exercise enforcement 
authority, they may--
    (1) Issue a warning letter, as provided in Sec. 107.309;
    (2) Initiate proceedings to assess a civil penalty, as provided in 
either Sec. Sec. 107.310 or 107.311;
    (3) Issue an order directing compliance, regardless of whether a 
warning letter has been issued or a civil penalty assessed; and
    (4) Seek any other remedy available under the Federal hazardous 
material transportation law.
    (b) In the case of a proceeding initiated for failure to comply with 
an exemption or special permit, the allegation of a violation of a term 
or condition thereof is considered by the Associate Administrator and 
the Office of Chief Counsel to constitute an allegation that the special 
permit holder or party to the special permit is failing, or has failed 
to comply with the underlying regulations from which relief was granted 
by the special permit.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-32, 59 
FR 49131, Sept. 26, 1994; Amdt. 107-36, 61 FR 7183, Feb. 26, 1996; 66 FR 
45377, Aug. 28, 2001; 70 FR 73162, Dec. 9, 2005]

[[Page 38]]



Sec. 107.309  Warning letters.

    (a) The Associate Administrator may issue a warning letter to any 
person whom the Associate Administrator believes to have committed a 
probable violation of the Federal hazardous material transportation law 
or any provision of this subchapter, subchapter C of this chapter, or 
any special permit issued thereunder.
    (b) A warning letter issued under this section includes:
    (1) A statement of the facts upon which the Associate Administrator 
bases its determination that the person has committed a probable 
violation;
    (2) A statement that the recurrence of the probable violations cited 
may subject the person to enforcement action; and
    (3) An opportunity to respond to the warning letter by submitting 
pertinent information or explanations concerning the probable violations 
cited therein.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51 
FR 34986, Oct. 1, 1986; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; Amdt. 
107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 107-36, 61 FR 7183, Feb. 26, 
1996; 66 FR 45377, Aug. 28, 2001]



Sec. 107.310  Ticketing.

    (a) For an alleged violation that does not have a direct or 
substantial impact on safety, the Associate Administrator may issue a 
ticket.
    (b) The Associate Administrator issues a ticket by mailing it by 
certified or registered mail to the person alleged to have committed the 
violation. The ticket includes:
    (1) A statement of the facts on which the Associate Administrator 
bases the conclusion that the person has committed the alleged 
violation;
    (2) The maximum penalty provided for by statute, the proposed full 
penalty determined according to PHMSA's civil penalty guidelines and the 
statutory criteria for penalty assessment, and the ticket penalty 
amount; and
    (3) A statement that within 45 days of receipt of the ticket, the 
person must pay the penalty in accordance with paragraph (d) of this 
section, make an informal response under Sec. 107.317, or request a 
formal administrative hearing under Sec. 107.319.
    (c) If the person makes an informal response or requests a formal 
administrative hearing, the Associate Administrator forwards the 
inspection report, ticket and response to the Office of the Chief 
Counsel for processing under Sec. Sec. 107.307-107.339, except that the 
Office of the Chief Counsel will not issue a Notice of Probable 
Violation under Sec. 107.311. The Office of the Chief Counsel may 
impose a civil penalty that does not exceed the proposed full penalty 
set forth in the ticket.
    (d) Payment of the ticket penalty amount must be made in accordance 
with the instructions on the ticket.
    (e) If within 45 days of receiving the ticket the person does not 
pay the ticket amount, make an informal response, or request a formal 
administrative hearing, the person has waived the right to make an 
informal response or request a hearing, has admitted the violation and 
owes the ticket penalty amount to PHMSA.

[Amdt. 107-36, 61 FR 7183, Feb. 26, 1996, as amended at 66 FR 45377, 
Aug. 28, 2001]



Sec. 107.311  Notice of probable violation.

    (a) The Office of Chief Counsel may serve a notice of probable 
violation on a person alleging the violation of one or more provisions 
of the Federal hazardous material transportation law or any provision of 
this subchapter or subchapter C of this chapter, or any special permit, 
or order issued thereunder.
    (b) A notice of probable violation issued under this section 
includes the following information:
    (1) A citation of the provisions of the Federal hazardous material 
transportation law, an order issued thereunder, this subchapter, 
subchapter C of this chapter, or the terms of any special permit issued 
thereunder which the Office of Chief Counsel believes the respondent is 
violating or has violated.
    (2) A statement of the factual allegations upon which the demand for 
remedial action, a civil penalty, or both, is based.
    (3) A statement of the respondent's right to present written or oral 
explanations, information, and arguments in answer to the allegations 
and in mitigation of the sanction sought in the notice of probable 
violation.

[[Page 39]]

    (4) A statement of the respondent's right to request a hearing and 
the procedures for requesting a hearing.
    (5) In addition, in the case of a notice of probable violation 
proposing a compliance order, a statement of the proposed actions to be 
taken by the respondent to achieve compliance.
    (6) In addition, in the case of a notice of probable violation 
proposing a civil penalty:
    (i) A statement of the maximum civil penalty for which the 
respondent may be liable;
    (ii) The amount of the preliminary civil penalty being sought by the 
Office of Chief Counsel, constitutes the maximum amount the Chief 
Counsel may seek throughout the proceeding; and
    (iii) A description of the manner in which the respondent makes 
payment of any money due the United States as a result of the 
proceeding.
    (c) The Office of Chief Counsel may amend a notice of probable 
violation at any time before issuance of a compliance order or an order 
assessing a civil penalty. If the Office of Chief Counsel alleges any 
new material facts or seeks new or additional remedial action or an 
increase in the amount of the proposed civil penalty, it issues a new 
notice of probable violation under this section.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 50 FR 45730, 
Nov. 1, 1985; Amdt. 107-24, 56 FR 8624, Feb. 28, 1991; Amdt. 107-32, 59 
FR 49131, Sept. 26, 1994; Amdt. 107-35, 60 FR 49108, Sept. 21, 1995; 
Amdt. 107-36, 61 FR 7184, Feb. 26, 1996]



Sec. 107.313  Reply.

    (a) Within 30 days of receipt of a notice of probable violation, the 
respondent must either:
    (1) Admit the violation under Sec. 107.315;
    (2) Make an informal response under Sec. 107.317; or
    (3) Request a hearing under Sec. 107.319.
    (b) Failure of the respondent to file a reply as provided in this 
section constitutes a waiver of the respondent's right to appear and 
contest the allegations and authorizes the Chief Counsel, without 
further notice to the respondent, to find the facts to be as alleged in 
the notice of probable violation and issue an order directing compliance 
or assess a civil penalty, or, if proposed in the notice, both. Failure 
to request a hearing under paragraph (a)(3) of this section constitutes 
a waiver of the respondent's right to a hearing.
    (c) Upon the request of the respondent, the Office of Chief Counsel 
may, for good cause shown and filed within the 30 days prescribed in the 
notice of probable violation, extend the 30-day response period.



Sec. 107.315  Admission of violations.

    (a) In responding to a notice of probable violation issued under 
Sec. 107.311, the respondent may admit the alleged violations and agree 
to accept the terms of a proposed compliance order or to pay the amount 
of the preliminarily assessed civil penalty, or, if proposed in the 
notice, both.
    (b) If the respondent agrees to the terms of a proposed compliance 
order, the Chief Counsel issues a final order prescribing the remedial 
action to be taken by the respondent.
    (c) Payment of a civil penalty, when the amount of the penalty 
exceeds $10,000, must be made by wire transfer, through the Federal 
Reserve Communications System (Fedwire), to the account of the U.S. 
Treasury. Detailed instructions on making payments by wire transfer may 
be obtained from the Financial Operations Division (AMZ-120), Federal 
Aviation Administration, Mike Monroney Aeronautical Center, P.O. Box 
25082, Oklahoma City, OK 73125.
    (d) Payment of a civil penalty, when the amount of the penalty is 
$10,000 or less, must be made either by wire transfer, as set forth in 
paragraph (c) of this section, or certified check or money order payable 
to ``U.S. Department of Transportation'' and submitted to the Financial 
Operations Division (AMZ-120), Federal Aviation Administration, Mike 
Monroney Aeronautical Center, P.O. Box 25082, Oklahoma City, OK 73125.

[Amdt. 107-11, 48 FR 265l, Jan. 20, 1983, as amended by Amdt. 107-23, 57 
FR 45453, Oct. 1, 1992; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; Amdt. 
107-38, 61 FR 21100, May 9, 1996; 68 FR 52848, Sept. 8, 2003]

[[Page 40]]



Sec. 107.317  Informal response.

    (a) In responding to a notice of probable violation under Sec. 
107.311, the respondent may submit to the official who issued the 
notice, written explanations, information, or arguments in response to 
the allegations, the terms of a proposed compliance order, or the amount 
of the preliminarily assessed civil penalty.
    (b) The respondent may include in his informal response a request 
for a conference. Upon the request of the respondent, the conference may 
be either in person or by telephone. A request for a conference must set 
forth the issues the respondent will raise at the conference.
    (c) Upon receipt of a request for a conference under paragraph (b) 
of this section, the Chief Counsel's Office, in consultation with the 
Associate Administrator, arranges for a conference as soon as 
practicable at a time and place of mutual convenience.
    (d) The respondent's written explanations, information, and 
arguments as well as the respondent's presentation at a conference are 
considered by the Chief Counsel in reviewing the notice of probable 
violation. Based upon a review of the proceeding, the Chief Counsel may 
dismiss the notice of probable violation in whole or in part. If he does 
not dismiss it in whole, he issues an order directing compliance or 
assessing a civil penalty, or, if proposed in the notice, both.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-23, 56 
FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]



Sec. 107.319  Request for a hearing.

    (a) In responding to a notice of probable violation under Sec. 
107.311, the respondent may request a formal administrative hearing on 
the record before an Administrative Law Judge (ALJ) obtained by the 
Office of the Chief Counsel.
    (b) A request for a hearing under paragraph (a) of this section 
must:
    (1) State the name and address of the respondent and of the person 
submitting the request if different from the respondent;
    (2) State which allegations of violations, if any, are admitted; and
    (3) State generally the issues to be raised by the respondent at the 
hearing. Issues not raised in the request are not barred from 
presentation at the hearing; and
    (4) Be addressed to the official who issued the notice.
    (c) After a request for a hearing that complies with the 
requirements of paragraph (b) of this section, the Chief Counsel obtains 
an ALJ to preside over the hearing and notifies the respondent of this 
fact. Upon assignment of an ALJ, further matters in the proceeding 
generally are conducted by and through the ALJ, except that the Chief 
Counsel and respondent may compromise or settle the case under Sec. 
107.327 of this subpart without order of the ALJ or voluntarily dismiss 
the case under Rule 41(a)(1) of the Federal Rules of Civil Procedure 
without order of the ALJ; in the event of such a compromise, settlement 
or dismissal, the Chief Counsel expeditiously will notify the ALJ 
thereof.
    (d) At any time after requesting a formal administrative hearing but 
prior to the issuance of a decision and final order by the ALJ, the 
respondent may withdraw such request in writing, thereby terminating the 
jurisdication of the ALJ in the case. Such a withdrawal constitutes an 
irrevocable waiver of respondent's right to such a hearing on the facts, 
allegations, and proposed sanction presented in the notice of probable 
violation to which the request for hearing relates.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 48 FR 17094, 
Apr. 21, 1983; Amdt. No. 107-19, 54 FR 22899, May 30, 1989]



Sec. 107.321  Hearing.

    (a) To the extent practicable, the hearing is held in the general 
vicinity of the place where the alleged violation occurred or at a place 
convenient to the respondent. Testimony by witnesses shall be given 
under oath and the hearing shall be recorded verbatim.
    (b) Hearings are conducted in accordance with the Federal Rules of 
Evidence and Federal Rules of Civil Procedure; however, the ALJ may 
modify them as he determines necessary in the interest of a full 
development of the facts. In addition, the ALJ may:

[[Page 41]]

    (1) Administer oaths and affirmations;
    (2) Issue subpoenas as provided by Sec. 105.45;
    (3) Adopt procedures for the submission of motions, evidence, and 
other documents pertinent to the proceeding;
    (4) Take or cause depositions to be taken;
    (5) Rule on offers of proof and receive relevant evidence;
    (6) Examine witnesses at the hearing;
    (7) Convene, recess, reconvene, adjourn and otherwise regulate the 
course of the hearing;
    (8) Hold conferences for settlement, simplification of the issues, 
or any other proper purpose; and
    (9) Take any other action authorized by, or consistent with, the 
provisions of this subpart and permitted by law which may expedite the 
hearing or aid in the disposition of an issue raised therein.
    (c) The official who issued the notice of probable violation, or his 
representative, has the burden of proving the facts alleged therein.
    (d) The respondent may appear and be heard on his own behalf or 
through counsel of his choice. The respondent or his counsel may offer 
relevant information including testimony which he believes should be 
considered in opposition to the allegations or which may bear on the 
sanction being sought and conduct such cross-examination as may be 
required for a full disclosure of the facts.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 67 FR 61011, 
Sept. 27, 2002]



Sec. 107.323  ALJ's decision.

    (a) After consideration of all matters of record in the proceeding, 
the ALJ shall issue an order dismissing the notice of probable violation 
in whole or in part or granting the sanction sought by the Office of 
Chief Counsel in the notice. If the ALJ does not dismiss the notice of 
probable violation in whole, he issues an order directing compliance or 
assessing a civil penalty, or, if proposed in the notice, both. The 
order includes a statement of the findings and conclusions, and the 
reasons therefore, on all material issues of fact, law, and discretion.
    (b) If, within 20 days of receipt of an order issued under paragraph 
(a) of this section, the respondent does not submit in writing his 
acceptance of the terms of an order directing compliance, or, where 
appropriate, pay a civil penalty, or file an appeal under Sec. 107.325, 
the case may be referred to the Attorney General with a request that an 
action be brought in the appropriate United States District Court to 
enforce the terms of a compliance order or collect the civil penalty.



Sec. 107.325  Appeals.

    (a) Hearing proceedings. A party aggrieved by an ALJ's decision and 
order issued under Sec. 107.323, may file a written appeal in 
accordance with paragraph (c) of this section with the Administrator, 
Office of the Administrator, Pipeline and Hazardous Materials Safety 
Administration, East Building, 1200 New Jersey Avenue, SE., Washington, 
DC 20590-0001.
    (b) Non-Hearing proceedings. A respondent aggrieved by an order 
issued under Sec. 107.317, may file a written appeal in accordance with 
paragraph (c) of this section with the Administrator, Office of the 
Administrator, Pipeline and Hazardous Materials Safety Administration, 
East Building, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001.
    (c) An appeal of an order issued under this subpart must:
    (1) Be filed within 20 days of receipt of the order by the appealing 
party; and
    (2) State with particularity the findings in the order that the 
appealing party challenges, and include all information and arguments 
pertinent thereto.
    (d) If the Administrator, PHMSA, affirms the order in whole or in 
part, the respondent must comply with the terms of the decision within 
20 days of the respondent's receipt thereof, or within the time 
prescribed in the order. If the respondent does not comply with the 
terms of the decision within 20 days of receipt, or within the time 
prescribed in the order, the case may be referred to the Attorney 
General for action to enforce the terms of the decision.

[[Page 42]]

    (e) The filing of an appeal stays the effectiveness of an order 
issued under Sec. 107.317 or Sec. 107.323. However, if the 
Administrator, PHMSA, determines that it is in the public interest, he 
may keep an order directing compliance in force pending appeal.

[70 FR 56090, Sept. 23, 2005, as amended at 72 FR 55683, Oct. 1, 2007]



Sec. 107.327  Compromise and settlement.

    (a) At any time before an order issued under Sec. 107.317 or Sec. 
107.323 is referred to the Attorney General for enforcement, the 
respondent or the Office of Chief Counsel may propose a compromise as 
follows:
    (1) In civil penalty cases, the respondent or Chief Counsel may 
offer to compromise the amount of the penalty by submitting an offer for 
a specific amount to the other party. An offer of compromise by the 
respondent shall be submitted to the Chief Counsel who may, after 
consultation with the Associate Administrator, accept or reject it.
    (i) A compromise offer stays the running of any response period then 
outstanding.
    (ii) If a compromise is agreed to by the parties, the respondent is 
notified in writing. Upon receipt of payment by Office of Chief Counsel, 
the respondent is notified in writing that acceptance of payment is in 
full satisfaction of the civil penalty proposed or assessed, and Office 
of Chief Counsel closes the case with prejudice to the respondent.
    (iii) If a compromise cannot be agreed to, the respondent is 
notified in writing and is given 10 days or the amount of time remaining 
in the then outstanding response period, whichever is longer, to respond 
to whatever action was taken by the Office of Chief Counsel or the 
Administrator, PHMSA.
    (2) In compliance order cases, the respondent may propose a consent 
agreement to the Chief Counsel. If the Chief Counsel accepts the 
agreement, he issues an order in accordance with its terms. If the Chief 
Counsel rejects the agreement, he directs that the proceeding continue. 
An agreement submitted to the Chief Counsel must include:
    (i) A statement of any allegations of fact which the respondent 
challenges;
    (ii) The reasons why the terms of a compliance order or proposed 
compliance order are or would be too burdensome for the respondent, or 
why such terms are not supported by the record in the case;
    (iii) A proposed compliance order suitable for issuance by the Chief 
Counsel;
    (iv) An admission of all jurisdictional facts; and
    (v) An express waiver of further procedural steps and all right to 
seek judicial review or otherwise challenge or contest the validity of 
the order.
    (b) Notwithstanding paragraph (a)(1) of this section, the respondent 
or Office of Chief Counsel may propose to settle the case. If the Chief 
Counsel agrees to a settlement, the respondent is notified and the case 
is closed without prejudice to the respondent.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended at 50 FR 45730, 
Nov. 1, 1985; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; 56 FR 15510, Apr. 
17, 1991; Amdt. 107-29, 58 FR 51527, Oct. 1, 1993; 66 FR 45377, Aug. 28, 
2001]



Sec. 107.329  Maximum penalties.

    (a) A person who knowingly violates a requirement of the Federal 
hazardous material transportation law, an order issued thereunder, this 
subchapter, subchapter C of this chapter, or a special permit or 
approval issued under this subchapter applicable to the transportation 
of hazardous materials or the causing of them to be transported or 
shipped is liable for a civil penalty of not more than $55,000 and not 
less than $250 for each violation, except the maximum civil penalty is 
$110,000 if the violation results in death, serious illness or severe 
injury to any person or substantial destruction of property, and a 
minimum $495 civil penalty applies to a violation relating to training. 
When the violation is a continuing one, each day of the violation 
constitutes a separate offense.
    (b) A person who knowingly violates a requirement of the Federal 
hazardous material transportation law, an order issued thereunder, this 
subchapter, subchapter C of this chapter, or a special permit or 
approval issued under

[[Page 43]]

this subchapter applicable to the design, manufacture, fabrication, 
inspection, marking, maintenance, reconditioning, repair or testing of a 
package, container, or packaging component which is represented, marked, 
certified, or sold by that person as qualified for use in the 
transportation of hazardous materials in commerce is liable for a civil 
penalty of not more than $55,000 and not less than $250 for each 
violation, except the maximum civil penalty is $110,000 if the violation 
results in death, serious illness or severe injury to any person or 
substantial destruction of property, and a minimum $495 civil penalty 
applies to a violation relating to training.

[71 FR 8487, Feb. 17, 2006, as amended at 74 FR 68702, Dec. 29, 2009; 75 
FR 53596, Sept. 1, 2010]



Sec. 107.331  Assessment considerations.

    After finding a knowing violation under this subpart, the Office of 
Chief Counsel assesses a civil penalty taking the following into 
account:
    (a) The nature and circumstances of the violation;
    (b) The extent and gravity of the violation;
    (c) The degree of the respondent's culpability;
    (d) The respondent's prior violations;
    (e) The respondent's ability to pay;
    (f) The effect on the respondent's ability to continue in business; 
and
    (g) Such other matters as justice may require.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-30, 58 
FR 50500, Sept. 27, 1993; Amdt. 107-38, 61 FR 21100, May 9, 1996]

                           Criminal Penalties



Sec. 107.333  Criminal penalties generally.

    A person who knowingly violates Sec. 171.2(l) of this title or 
willfully or recklessly violates a requirement of the Federal hazardous 
material transportation law or a regulation, order, special permit, or 
approval issued thereunder shall be fined under title 18, United States 
Code, or imprisoned for not more than 5 years, or both, except the 
maximum amount of imprisonment shall be 10 years in any case in which 
the violation involves the release of a hazardous material which results 
in death or bodily injury to any person.

[71 FR 8487, Feb. 17, 2006]



Sec. 107.335  Referral for prosecution.

    If the Associate Administrator becomes aware of a possible willful 
violation of the Federal hazardous material transportation law, this 
subchapter, subchapter C of this chapter, or any special permit, or 
order issued thereunder, for which the Associate Administrator exercises 
enforcement responsibility, it shall report it to the Office of the 
Chief Counsel, Pipeline and Hazardous Materials Safety Administration, 
U.S. Department of Transportation, Washington, DC 20590-0001. If 
appropriate, the Chief Counsel refers the report to the Department of 
Justice for criminal prosecution of the offender.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-22, 55 
FR 39978, Oct. 1, 1990; Amdt. 107-24, 56 FR 8621, Feb. 28, 1991; 56 FR 
15510, Apr. 17, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; Amdt. 
107-35, 60 FR 49108, Sept. 21, 1995; 66 FR 45377, Aug. 28, 2001]



Sec. 107.336  Limitation on fines and penalties.

    If a State or political subdivision or Indian tribe assesses any 
fine or penalty determined by the Secretary to be appropriate for a 
violation concerning a subject listed in Sec. 107.202(a), no additional 
fine or penalty may be assessed for such violation by any other 
authority.

[Amdt. 107-24, 56 FR 8624, Feb. 28, 1991]

                            Injunctive Action



Sec. 107.337  Injunctions generally.

    Whenever it appears to the Office of Chief Counsel that a person has 
engaged, or is engaged, or is about to engage in any act or practice 
constituting a violation of any provision of the Federal hazardous 
material transportation law, this subchapter, subchapter C of this 
chapter, or any special permit, or order issued thereunder, for which 
the Office of Chief Counsel exercises enforcement responsibility,

[[Page 44]]

the Administrator, PHMSA, or his delegate, may request the Attorney 
General to bring an action in the appropriate United States District 
Court for such relief as is necessary or appropriate, including 
mandatory or prohibitive injunctive relief, interim equitable relief, 
and punitive damages as provided by 49 U.S.C. 5122(a).

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-32, 59 
FR 49131, Sept. 26, 1994]



Sec. 107.339  Imminent hazards.

    Whenever it appears to the Office of the Chief Counsel that there is 
a substantial likelihood that death, serious illness, or severe personal 
injury will result from the transportation of a particular hazardous 
material or hazardous materials container, before a compliance order 
proceeding or other administrative hearing or formal proceeding to abate 
the risk of that harm can be completed, the Administrator, PHMSA, or his 
delegate, may bring an action under 49 U.S.C. 5122(b) in the appropriate 
United States District Court for an order suspending or restricting the 
transporation of that hazardous material or those containers or for such 
other equitable relief as is necessary or appropriate to ameliorate the 
hazard.

[Amdt. 107-11, 48 FR 2651, Jan. 20, 1983, as amended by Amdt. 107-15, 51 
FR 34987, Oct. 1, 1986; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994]



Sec. Appendix A to Subpart D of Part 107--Guidelines for Civil Penalties

    I. This appendix sets forth the guidelines used by the Office of 
Hazardous Materials Safety (as of October 1, 2005) in making initial 
baseline determinations for recommending civil penalties. The first part 
of these guidelines is a list of baseline amounts or ranges for probable 
violations frequently cited in enforcement reports referred for action. 
Following the list of violations are general guidelines used by OHMS in 
making initial penalty determinations in enforcement cases.

                 II. List of Frequently Cited Violations

                 II--List of Frequently Cited Violations
------------------------------------------------------------------------
    Violation description        Section or cite     Baseline assessment
------------------------------------------------------------------------
                          General Requirements
------------------------------------------------------------------------
 
A. Registration               107.608, 107.612....  $1,000 + $500 each
 Requirements: Failure to                            additional year.
 register as an offeror or
 carrier of hazardous
 material and pay
 registration fee.
B. Training Requirements:
    1. Failure to provide     172.702
     initial training to
     hazmat employees
     (general awareness,
     function-specific,
     safety, and security
     awareness training):
        a. More than 10       ....................  $700 and up each
         hazmat employees.                           area.
        b. 10 hazmat          ....................  $450 and up each
         employees or fewer.                         area.
    2. Failure to provide     172.702.............  $450 and up each
     recurrent training to                           area.
     hazmat employees
     (general awareness,
     function-specific,
     safety, and security
     awareness training).
    3. Failure to provide     172.702.............  Included in penalty
     security training when                          for no security
     a security plan is                              plan.
     required but has not
     been developed.
    4. Failure to provide     172.702.............  $2,500.
     security training when
     a security plan has
     been developed but
     hazmat employees have
     not been trained
     concerning the security
     plan and its
     implementation.
    5. Failure to create and  172.704
     maintain training
     records:
        a. more than 10       ....................  $800 and up.
         hazmat employees.
        b. 10 hazmat          ....................  $500 and up.
         employees or fewer.
C. Security Plans:
    1. Failure to develop a   172.800
     security plan; failure
     to adhere to security
     plan:
        a. Sec.  172.504     ....................  $7,500.
         table 1 materials.
        b. Packing Group I..  ....................  $6,000.
        c. Packing Group II.  ....................  $4,500.
        d. Packing Group III  ....................  $3,000.
    2. Incomplete security    ....................  One-quarter (25%) of
     plan or incomplete                              above for each
     adherence (one or more                          element.
     of four required
     elements missing).
    3. Failure to update a    172.802(b)..........  One-third (33%) of
     security plan to                                baseline for no
     reflect changing                                plan.
     circumstances.

[[Page 45]]

 
    4. Failure to put         172.800(b)..........  One-third (33%) of
     security plan in                                baseline for no
     writing; failure to                             plan.
     make all copies
     identical.
D. Notification to a Foreign  171.12(a)...........  $1,500 to $7,500
 Shipper: Failure to provide                         (corresponding to
 information of HMR                                  violations by
 requirements applicable to                          foreign offeror or
 a shipment of hazardous                             forwarding agent).
 materials within the United
 States, to a foreign
 offeror or forwarding agent
 at the place of entry into
 the U.S.
E. Expired Exemption or       171.2(a), (b), (c),   $1,000 + $500 each
 Special Permit: Offering or   Various.              additional year.
 transporting a hazardous
 material, or otherwise
 performing a function
 covered by an exemption or
 special permit, after
 expiration of the exemption
 or special permit
------------------------------------------------------------------------
 
              Offeror Requirements--All hazardous materials
------------------------------------------------------------------------
 
A. Undeclared Shipment:
    Offering for              172.200, 172.300,     $15,000 and up.
     transportation a          172.400, 172.500.
     hazardous material
     without shipping
     papers, package
     markings, labels, or
     placards.
B. Shipping Papers:
    1. Failure to provide a   172.201.............  $3,000 to $6,000.
     shipping paper for a
     shipment of hazardous
     materials.
    2. Failure to follow one  172.201(a)(1).......  $1,200.
     or more of the three
     approved formats for
     listing hazardous
     materials on a shipping
     paper.
    3. Failure to retain
     shipping papers:.
        a. by an offeror,
         for two years after
         the date the
         shipment is
         provided to the
         carrier (or 3 years
         if the material is
         a hazardous waste).
        b. by a carrier, for  172.201(e),           $1,000.
         one year after the    174.24(b),
         date the shipment     175.30(a),
         is provided to the    176.24(b),
         carrier (or 3 years   177.817(f).
         if the material is
         a hazardous waste).
    4. Failure to include a   172.202.............  $800 to $1,600.
     proper shipping name in
     the shipping
     description or using an
     incorrect proper
     shipping name.
    5. Failure to include a   172.202.............  $1,000 to $2,000.
     hazard class/division
     number in the shipping
     description.
    6. Failure to include an  172.202.............  $1,000 to $2,000.
     identification number
     in the shipping
     description.
    7. Using an incorrect     172.202.............
     hazard class/
     identification number:.
        a. that does not      ....................  $800.
         affect
         compatibility
         requirements.
        b. that affects       ....................  $3,000 to $6,000.
         compatibility
         requirements.
    8. Using an incorrect     172.202.............
     identification number:.
        a. that does not      ....................  $800.
         change the response
         information.
        b. that changes the   ....................  $3,000 to $6,000.
         response
         information.
    9. Failure to include     172.202.............  $1,200.
     the Packing Group, or
     using an incorrect
     Packing Group.
    10. Using a shipping      172.202.............  $800.
     description that
     includes additional
     unauthorized
     information (extra or
     incorrect words).
    11. Using a shipping      172.202.............  $500.
     description not in
     required sequence.
    12. Using a shipping      172.202.............
     description with two or
     more required elements
     missing or incorrect:.
        a. such that the      ....................  $3,000.
         material is
         misdescribed.
        b. such that the      ....................  $6,000.
         material is
         misclassified.
    13. Failure to include    172.202(c)..........  $500.
     the total quantity of
     hazardous material
     covered by a shipping
     description.
    14. Failure to list an    172.203(a)..........  $800.
     exemption or special
     permit number in
     association with the
     shipping description.
    15. Failure to indicate   172.203(b)..........  $500.
     ``Limited Quantity'' or
     ``Ltd Qty'' following
     the basic shipping
     description of a
     material offered for
     transportation as a
     limited quantity.
    16. Failure to include    172.203(c)(2).......  $500.
     ``RQ'' in the shipping
     description to identify
     a material that is a
     hazardous substance.
    17. Failure to include a  172.203(k)..........  $1,000.
     required technical name
     in parenthesis for a
     listed generic or
     ``n.o.s.'' material.
    18. Failure to include    172.204.............  $1,000.
     the required shipper's
     certification on a
     shipping paper.
    19. Failure to sign the   172.204.............  $800.
     required shipper's
     certification on a
     shipping paper.
C. Emergency Response
 Information Requirements:
    1. Providing or listing   172.602.............
     incorrect emergency
     response information
     with or on a shipping
     paper.
        a. No significant     ....................  $800.
         difference in
         response.
        b. Significant        ....................  $3,000 to $6,000.
         difference in
         response.

[[Page 46]]

 
    2. Failure to include an  172.604.............  $2,600.
     emergency response
     telephone number on a
     shipping paper.
    3. Failure to have the    172.604.............  $1,300.
     emergency response
     telephone number
     monitored while a
     hazardous material is
     in transportation or
     listing multiple
     telephone numbers
     (without specifying the
     times for each) that
     are not monitored 24
     hours a day.
    4. Listing an             172.604.............  $2,600 to $4,200.
     unauthorized emergency
     response telephone
     number on a shipping
     paper.
    5. Listing an incorrect   172.604.............  $1,300.
     or non-working
     emergency response
     telephone number on a
     shipping paper.
    6. Failure to provide     172.604.............  $1,300.
     required technical
     information when the
     listed emergency
     response telephone
     number is contacted.
D. Package Marking
 Requirements:
    1. Failure to mark the    172.301(a)..........  $800 to $1,600.
     proper shipping name on
     a package or marking an
     incorrect shipping name
     on a package.
    2. Failure to mark the    172.301(a)..........  $1,000 to $2,000.
     identification number
     on a package.
    3. Marking a package      172.301(a)..........
     with an incorrect
     identification number.
        a. that does not      ....................  $800.
         change the response
         information.
        b. that changes the   ....................  $3,000 to $6,000.
         response
         information.
    4. Failure to mark the    172.301(a)..........  $3,000 to $6,000.
     proper shipping name
     and identification
     number on a package.
    5. Marking a package      172.301(a)..........
     with an incorrect
     shipping name and
     identification number.
        a. that does not      ....................  $1,500 to $3,000.
         change the response
         information.
        b. that changes the   ....................  $3,000 to $6,000.
         response
         information.
    6. Failure to include     172.301(c)..........  $1,000.
     the required technical
     name(s) in parenthesis
     for a listed generic or
     ``n.o.s.'' entry.
    7. Marking a package as   172.303(a)..........  $800.
     containing hazardous
     material when it
     contains no hazardous
     material.
    8. Failure to locate      172.304(a)(4).......  $800.
     required markings away
     from other markings
     that could reduce their
     effectiveness.
    9. Failure to mark a      172.312.............  $2,500 to $3,500.
     package containing
     liquid hazardous
     materials with required
     orientation marking.
    10. Failure to mark       172.324(b)..........  $500.
     ``RQ'' on a non-bulk
     package containing a
     hazardous substance.
E. Package Labeling
 Requirements:
    1. Failure to label a     172.400.............  $5,000.
     package.
    2. Placing a label that   172.400.............  $5,000.
     represents a hazard
     other than the hazard
     presented by the
     hazardous material in
     the package.
    3. Placing a label on a   172.401(a)..........  $800.
     package that does not
     contain a hazardous
     material.
    4. Failure to place a     172.402.............  $500 to $2,500.
     required subsidiary
     label on a package.
    5. Placing a label on a   172.406(a)..........  $800.
     different surface of
     the package than, or
     away from, the proper
     shipping name.
    6. Placing an improper    172.407(c)..........  $800.
     size label on a package.
    7. Placing a label on a   172.407(d)..........  $600 to $2,500.
     package that does not
     meet color
     specification
     requirements (depending
     on the variance).
    8. Failure to provide an  172.411.............  $2,500.
     appropriate class or
     division number on a
     label.
F. Placarding Requirements:
    Failure to properly       172.504.............
     placard a freight
     container or vehicle
     containing hazardous
     materials:.
        a. when Table 1 is    ....................  $1,000 to $9,000.
         applicable.
        b. when Table 2 is    ....................  $800 to $7,200.
         applicable.
G. Packaging Requirements:
    1. Offering a hazardous   Various.............
     material for
     transportation in an
     unauthorized non-UN
     standard or
     nonspecification
     packaging (includes
     failure to comply with
     the terms of an
     exemption or special
     permit authorizing use
     of a nonstandard or
     nonspecification
     packaging).
        a. Packing Group I    ....................  $9,000.
         (and Sec.  172.504
         Table I materials).
        b. Packing Group II.  ....................  $7,000.
        c. Packing Group III  ....................  $5,000.
    2. Offering a hazardous   178.601 & Various...
     material for
     transportation in a
     self-certified
     packaging that has not
     been subjected to
     design qualification
     testing:.
        a. Packing Group I    ....................  $10,800.
         (and Sec.  172.504
         Table I materials).
        b. Packing Group II.  ....................  $8,400.
        c. Packing Group III  ....................  $6,000.
    3. Offering a hazardous   178.503(a)..........  $3,600.
     material for
     transportation in a
     packaging that has been
     successfully tested to
     an applicable UN
     standard but is not
     marked with the
     required UN marking.

[[Page 47]]

 
    4. Failure to close a UN  173.22(a)(4)........  $2,500.
     standard packaging in
     accordance with the
     closure instructions.
    5. Offering a hazardous   173.24(b)...........
     material for
     transportation in a
     packaging that leaks
     during conditions
     normally incident to
     transportation:
        a. Packing Group I    ....................  $12,000.
         (and Sec.  172.504
         Table I materials).
        b. Packing Group II.  ....................  $9,000.
        c. Packing Group III  ....................  $6,000.
    6. Overfilling or         173.24(b)...........
     underfilling a package
     so that the
     effectiveness is
     substantially reduced:
        a. Packing Group I    ....................  $9,000.
         (and Sec.  172.504
         Table I materials).
        b. Packing Group II.  ....................  $6,000.
        c. Packing Group III  ....................  $3,000.
    7. Offering a hazardous   171.14..............
     material for
     transportation after
     October 1, 1996, in an
     unauthorized non-UN
     standard packaging
     marked as manufactured
     to a DOT specification:
        a. packaging meets    ....................  $3,000.
         DOT specification.
        b. packaging does     ....................  $5,000 to $9,000.
         not meet DOT
         specification.
    8. Failure to mark an     173.25(a)(4)........  $3,000.
     overpack with a
     statement that the
     inside packages comply
     with prescribed
     specifications or
     standards when
     specification or
     standard packaging is
     required.
    9. Filling an IBC or a    173.32(a), 180.352,
     portable tank (DOT, UN,   180.605.
     or IM) that is out of
     test and offering
     hazardous materials for
     transportation in that
     IBC or portable tank.
        a. All testing        ....................  $3,500 to $7,000.
         overdue.
        b. Only periodic (5   ....................  $3,500.
         year) test overdue.
        c. Only intermediate  ....................  $3,500.
         periodic (2.5 year)
         tests overdue.
    10. Failure to provide    173.32(f)(6)........  $6,000 to $12,000.
     the required outage in
     a portable tank that
     results in a release of
     hazardous materials.
------------------------------------------------------------------------
 
           Offeror Requirements--Specific hazardous materials
------------------------------------------------------------------------
 
A. Cigarette Lighters:
    Offering for              173.21(i)...........  $7,500.
     transportation an
     unapproved cigarette
     lighter, lighter
     refill, or similar
     device, equipped with
     an ignition element and
     containing fuel.
B. Class 1--Explosives:
    1. Failure to mark the    172.320.............  $1,200.
     package with the EX
     number for each
     substance contained in
     the package or,
     alternatively, indicate
     the EX number for each
     substance in
     association with the
     description on the
     shipping description.
    2. Offering an            173.54, 173.56(b)...  ....................
     unapproved explosive
     for transportation:
        a. Div. 1.3 and 1.4   ....................  $5,000 to $10,000.
         fireworks meeting
         the chemistry
         requirements
         (quantity and type)
         of APA Standard 87-
         1.
        b. All other          ....................  $10,000 and up.
         explosives
         (including
         forbidden).
    3. Offering a leaking or  173.54(c)...........  $10,000 and up.
     damaged package of
     explosives for
     transportation.
    4. Packaging explosives   173.61..............  $2,500 to $5,000.
     in the same outer
     packaging with other
     materials.
C. Class 7--Radioactive
 Materials:
    1. Failure to include     172.203(d)..........  $1,000 to $3,000.
     required additional
     entries, or providing
     incorrect information
     for these additional
     entries.
    2. Failure to mark the    172.310(a)..........  $800.
     gross mass on the
     outside of a package of
     Class 7 material that
     exceeds 110 pounds.
    3. Failure to mark each   172.310(b)..........  $800.
     package in letters at
     least 13 mm (\1/2\
     inch) high with the
     words ``Type A'' or
     ``Type B'' as
     appropriate.
    4. Placing a label on     172.403.............  $5,000.
     Class 7 material that
     understates the proper
     label category.
    5. Placing a label on     172.403(g)..........  $2,000 to $4,000.
     Class 7 material that
     fails to contain (or
     has erroneous) entries
     for the name of the
     radionuclide(s),
     activity, and transport
     index.
    6. Failure to meet one    173.410.............  $5,000.
     or more of the general
     design requirements for
     a package used to ship
     a Class 7 material.
    7. Failure to comply      173.411.............  $5,000.
     with the industrial
     packaging (IP)
     requirements when
     offering a Class 7
     material for
     transportation.
    8. Failure to provide a   173.412(a)..........  $2,000.
     tamper-indicating
     device on a Type A
     package used to ship a
     Class 7 material.
    9. Failure to meet the    173.412(b)-(i)......  $5,000.
     additional design
     requirements of a Type
     A package used to ship
     a Class 7 material.
    10. Failure to meet the   173.412(j)-(l)......  $8,400.
     performance
     requirements for a Type
     A package used to ship
     a Class 7 material..

[[Page 48]]

 
    11. Offering a DOT        173.415(a), 173.461   ....................
     specification 7A
     packaging without
     maintaining complete
     documentation of tests
     and an engineering
     evaluation or
     comparative data:
        a. Tests and          ....................  $8,400.
         evaluation not
         performed.
        b. Complete records   ....................  $2,000 to $5,000.
         not maintained.
    12. Offering any Type B,  173.416.............  $9,000.
     Type B(U), Type B(M)
     packaging that failed
     to meet the approved
     DOT, NRC or DOE design,
     as applicable.
    13. Offering a Type B     173.471(a).           ....................
     packaging without
     holding a valid NRC
     approval certificate:
        a. Never having       ....................  $3,000.
         obtained one.
        b. Holding an         ....................  $1,000.
         expired certificate.
    14. Failure to meet one   173.420.............  $10,800.
     or more of the special
     requirements for a
     package used to ship
     uranium hexafluoride.
    15. Offering Class 7      173.421(a)..........  $4,000.
     material for
     transportation as a
     limited quantity
     without meeting the
     requirements for
     limited quantity.
    16. Offering a multiple-  173.423(a)..........  $500 to $2,500.
     hazard limited quantity
     Class 7 material
     without addressing the
     additional hazard.
    17. Offering Class 7 low  173.427(a)(1).......  $6,000.
     specific activity (LSA)
     materials or surface
     contaminated objects
     (SCO) with an external
     dose rate that exceeds
     an external radiation
     level of 1 rem/hr at 3
     meters from the
     unshielded material.
    18. Offering Class 7 LSA  173.427(a)(6).......  $1,000.
     materials or SCO as
     exclusive use without
     providing specific
     instructions to the
     carrier for maintenance
     of exclusive use
     shipment controls.
    19. Offering in excess    173.431.............  $12,000.
     of Type A quantity of a
     Class 7 material in a
     Type A packaging.
    20. Offering a package    173.441.............  $10,000 and up.
     that exceeds the
     permitted limits for
     surface radiation or
     transport index.
    21. Offering a package    173.443.............  $5,000 and up.
     without determining the
     level of removable
     external contamination,
     or that exceeds the
     limit for removable
     external contamination.
    22. Storing packages of   173.447(a)..........  $5,000 and up.
     radioactive material in
     a group with a total
     transport index more
     than 50.
    23. Offering for          173.448(e)..........  $5,000 and up.
     transportation or
     transporting aboard a
     passenger aircraft any
     single package or
     overpack of Class 7
     material with a
     transport index greater
     than 3.0.
    24. Exporting a Type B,   173.471(d)..........  $3,000.
     Type B(U), Type B(M),
     or fissile package
     without obtaining a
     U.S. Competent
     Authority Certificate
     or, after obtaining a
     U.S. Competent
     Authority Certificate,
     failing to submit a
     copy to the national
     competent authority of
     each country into or
     through which the
     package is transported.
    25. Offering special      173.476(a), (b).....  $2,500.
     form radioactive
     materials without
     maintaining a complete
     safety analysis or
     Certificate of
     Competent Authority.
D. Class 2--Compressed Gases                        ....................
 in Cylinders:
    1. Filling and offering   173.301(a)(6).......  $4,200 to $10,400.
     a cylinder with
     compressed gas when the
     cylinder is out of test.
    2. Failure to check each  173.303(d)..........  $5,000.
     day the pressure of a
     cylinder charged with
     acetylene that is
     representative of that
     day's compression,
     after the cylinder has
     cooled to a settled
     temperature, or failure
     to keep a record of
     this test for 30 days.
    3. Offering a limited     173.306(a)(3), (h)..  $1,500 to $6,000.
     quantity of a
     compressed gas in a
     metal container for the
     purpose of propelling a
     nonpoisonous material
     and failure to heat the
     cylinder until the
     pressure is equivalent
     to the equilibrium
     pressure at 130 [deg]F,
     without evidence of
     leakage, distortion, or
     other defect.
------------------------------------------------------------------------
 
          Manufacturing, Reconditioning, Retesting Requirements
------------------------------------------------------------------------
 
A. Third-Party Packaging
 Certifiers (General):
    Issuing a certification   171.2(e), 178.2(b),   $500 per item.
     that directs the          178.3(a),
     packaging manufacturer    178.503(a).
     to improperly mark a
     packaging (e.g., steel
     drum to be marked UN
     4G).
B. Packaging Manufacturers
 (General):
    1. Failure of a           178.2(c)............  $2,500.
     manufacturer or
     distributor to notify
     each person to whom the
     packaging is
     transferred of all the
     requirements not met at
     the time of transfer,
     including closure
     instructions.
    2. Failure to insure a    178.601(b)..........
     packaging certified as
     meeting the UN standard
     is capable of passing
     the required
     performance testing.
        a. Packing Group I    ....................  $10,800.
         (and Sec.  172.504
         Table 1 materials).
        b. Packing Group II.  ....................  $8,400.
        c. Packing Group III  ....................  $6,000.

[[Page 49]]

 
    3. Certifying a           178.601(d)..........
     packaging as meeting a
     UN standard when design
     qualification testing
     was not performed.
        a. Packing Group I    ....................  $10,800.
         (and Sec.  172.504
         table 1 materials).
        b. Packing Group II.  ....................  $8,400.
        c. Packing Group III  ....................  $6,000.
    4. Failure to conduct     178.601(e)..........  $2,000 to $10,800.
     periodic retesting on
     UN standard packaging
     (depending on length of
     time and Packing Group).
    5. Failure to properly
     conduct testing for UN
     standard packaging
     (e.g., testing with
     less weight than marked
     on packaging; drop
     testing from lesser
     height than required;
     failing to condition
     fiberboard boxes before
     design test):.
        a. Design             178.601(d)..........  $2,000 to $10,800.
         qualification
         testing.
        b. Periodic           178.601(e)..........  $500 to $10,800.
         retesting.
    6. Marking, or causing    178.2(b), 178.3(a),   $7,200.
     the marking of, a         178.503(a)(8).
     packaging with the
     symbol of a
     manufacturer or
     packaging certifier
     other than the company
     that actually
     manufactured or
     certified the packaging.
    7. Failure to maintain    178.601(l)..........
     testing records.
        a. Design             ....................  $1,000 to $5,000.
         qualification
         testing.
        b. Periodic           ....................  $500 to $2,000.
         retesting.
    8. Improper marking of    178.503.............  $500 per item.
     UN certification.
    9. Manufacturing DOT      171.14..............
     specification packaging
     after October 1, 1994
     that is not marked as
     meeting a UN
     performance standard.
        a. If packaging does  ....................  $3,000.
         meet DOT
         specification.
        b. If packaging does  ....................  $6,000 to $10,800.
         not meet DOT
         specification.
C. Drum Manufacturers &
 Reconditioners:
    1. Failure to properly    178.604(b), (d),
     conduct production        173.28(b)(2)(i).
     leakproofness test on a
     new or reconditioned
     drum.
        a. Improper testing.  ....................  $2,000.
        b. No testing         ....................  $3,000 to $5,000.
         performed.
    2. Marking an incorrect   173.28(b)(2)(ii)....
     registration number on
     a reconditioned drum.
        a. Incorrect number.  ....................  $800.
        b. Unauthorized use   ....................  $7,200.
         of another
         reconditioner's
         number.
    3. Representing,          173.28(c), (d)......  $6,000 to $10,800.
     marking, or certifying
     a drum as a
     reconditioned UN
     standard packaging when
     the drum does not meet
     a UN standard.
    4. Representing,          173.28(d)...........  $500.
     marking, or certifying
     a drum as altered from
     one UN standard to
     another, when the drum
     has not actually been
     altered.
D. IBC and Portable Tank
 Requalification:
    1. Failure to properly    180.352(e),           $500 per item.
     mark an IBC or portable   178.703(b),
     tank with the most        180.605(k).
     current retest and/or
     inspection information.
    2. Failure to keep        180.352(f),
     complete and accurate     180.605(l).
     records of IBC or
     portable tank retest
     and reinspection.
        a. No records kept..  ....................  $4,000.
        b. Incomplete or      ....................  $1,000 to $3,000.
         inaccurate records.
    3. Failure to make        180.352(f), 49        $1,000.
     reinspection and retest   U.S.C. 5121(b)(2).
     records available to a
     DOT representative upon
     request.
E. Cylinder Manufacturers &
 Rebuilders:
    1. Manufacturing,         Various.............  $7,500 to $15,000.
     representing, marking,
     certifying, or selling
     a DOT high-pressure
     cylinder that was not
     inspected and verified
     by an approved
     independent inspection
     agency.
    2. Failure to have a      Various.............  $800.
     registration number or
     failure to mark the
     registration number on
     the cylinder.
    3. Marking another        Various.............  $7,200.
     company's number on a
     cylinder.
    4. Failure to mark the    178.65(i)...........  $3,000.
     date of manufacture or
     lot number on a DOT-39
     cylinder.
    5. Failure to have a      Various.............  $5,000.
     chemical analysis
     performed in the U.S.
     for a material
     manufactured outside
     the U.S./failure to
     obtain a chemical
     analysis from the
     foreign manufacturer.
    6. Failure to meet wall   Various.............  $7,500 to $15,000.
     thickness requirements.
    7. Failure to heat treat  Various.............  $5,000 to $15,000.
     cylinders prior to
     testing.
    8. Failure to conduct a   Various.............  $2,500 to $6,200.
     complete visual
     internal examination.
    9. Failure to conduct a   Various.............  $2,500 to $6,200.
     hydrostatic test, or
     conducting a
     hydrostatic test with
     inaccurate test
     equipment.
    10. Failure to conduct a  Various.............  $7,500 to $15,000.
     flattening test.
    11. Failure to conduct a  178.65(f)(2)........  $5,000 to $15,000.
     burst test on a DOT-39
     cylinder.
    12. Failure to have       Various.............  $7,500 to $15,000.
     inspections and
     verifications performed
     by an inspector.
    13. Failure to maintain   Various.............
     required inspector's
     reports.
        a. No reports at all  ....................  $5,000.
        b. Incomplete or      ....................  $1,000 to $4,000.
         inaccurate reports.

[[Page 50]]

 
    14. Representing a DOT-4  180.211(a)..........  $6,000 to $10,800.
     series cylinder as
     repaired or rebuilt to
     the requirements of the
     HMR without being
     authorized by the
     Associate Administrator.
F. Cylinder Requalification:
    1. Failure to remark as   173.23(c)...........  $800.
     DOT 3AL an aluminum
     cylinder manufactured
     under a former
     exemption or special
     permit.
    2. Certifying or marking  180.205(a)..........  $800.
     as retested a
     nonspecification
     cylinder.
    3. Failure to have        180.205(b)..........  $4,000.
     retester's
     identification number
     (RIN).
    4. Failure to have        180.205(b)..........  $2,000.
     current authority due
     to failure to renew a
     retester's
     identification number
     (RIN).
    5. Failure to have a      180.205(b)..........  $7,200.
     retester's
     identification number
     and marking another RIN
     on a cylinder.
    6. Marking a RIN before   180.205(b)..........  $800.
     successfully completing
     a hydrostatic retest.
    7. Representing,          171.2(c), (e),        $2,000 to $6,000.
     marking, or certifying    180.205(c),
     a cylinder as meeting     Applicable
     the requirements of an    Exemption or
     exemption or special      Special Permit.
     permit when the
     cylinder was not
     maintained or retested
     in accordance with the
     exemption or special
     permit.
    8. Failure to conduct a   180.205(f)..........  $2,100 to $5,200.
     complete visual
     external and internal
     examination.
    9. Failure to conduct     180.205(f) & (g)....  $4,200 to $10,400.
     visual inspection or
     hydrostatic retest.
    10. Performing            180.205(g)(3).......  $2,100 to $5,200.
     hydrostatic retesting
     without confirming the
     accuracy of the test
     equipment.
    11. Failure to hold       180.205(g)(5).......  $3,100.
     hydrostatic test
     pressure for 30 seconds
     or sufficiently longer
     to allow for complete
     expansion.
    12. Failure to perform a  180.205(g)..........  $3,100.
     second retest, after
     equipment failure, at a
     pressure increased by
     the lesser of 10% or
     100 psi (includes
     exceeding 90% of test
     pressure prior to
     conducting a retest).
    13. Failure to condemn a  180.205(i)..........  $6,000 to $10,800.
     cylinder when required
     (e.g., permanent
     expansion of 10% [5%
     for certain exemption
     or special permit
     cylinders], internal or
     external corrosion,
     denting, bulging,
     evidence of rough
     usage).
    14. Failure to properly   180.205(i)(2).......  $800.
     mark a condemned
     cylinder or render it
     incapable of holding
     pressure.
    15. Failure to notify     180.205(i)(2).......  $1,000.
     the cylinder owner in
     writing when a cylinder
     has been condemned.
    16. Failure to perform    180.209(a)(1).......  $2,100 to $5,200.
     hydrostatic retesting
     at the minimum
     specified test pressure.
    17. Marking a star on a   180.209(b)..........  $2,000 to $4,000.
     cylinder that does not
     qualify for that mark.
    18. Marking a ``+'' sign  173.302a(b).........  $2,000 to $4,000.
     on a cylinder without
     determining the average
     or minimum wall stress
     by calculation or
     reference to CGA
     Pamphlet C-5.
    19. Marking a cylinder    180.213(b)..........  $6,000 to $10,800.
     in or on the sidewall
     when not permitted by
     the applicable
     specification.
    20. Failure to maintain   180.213(b)(1).......  $800.
     legible markings on a
     cylinder.
    21. Marking a DOT 3HT     180.213(c)(2).......  $6,000 to $10,800.
     cylinder with a steel
     stamp other than a low-
     stress steel stamp.
    22. Improper marking of   180.213(d)..........  $800.
     the RIN or retest date
     on a cylinder.
    23. Marking an FRP        Applicable Exemption  $6,000 to $10,800.
     cylinder with steel       or Special Permit.
     stamps in the FRP area
     of the cylinder such
     that the integrity of
     the cylinder is
     compromised.
    24. Failure to maintain   180.215(a)..........  $600 to $1,200.
     current copies of 49
     CFR, DOT exemption or
     special permits, and
     CGA Pamphlets
     applicable to
     inspection, retesting,
     and marking activities.
    25. Failure to keep       180.215(b)..........
     complete and accurate
     records of cylinder
     reinspection and retest.
        a. No records kept..  ....................  $4,000.
        b. Incomplete or      ....................  $1,000 to $3,000.
         inaccurate records.
    26. Failure to report in  171.2(c) & (e),       $600 to $1,200.
     writing a change in       Approval Letter.
     name, address,
     ownership, test
     equipment, management,
     or retester personnel.
------------------------------------------------------------------------
 
                          Carrier Requirements
------------------------------------------------------------------------
 
A. Incident Notification:
    1. Failure to give        171.15..............  $3,000.
     immediate notification
     of a reportable
     hazardous materials
     incident.
    2. Failure to file a      171.16..............  $500 to $2,500.
     written hazardous
     material incident
     report within 30 days
     following an
     unintentional release
     of hazardous materials
     in transportation (or
     other reportable
     incident).
B. Shipping Papers:

[[Page 51]]

 
    Failure to retain         174.24(b),            $1,000.
     shipping papers for 375   175.30(a)(2),
     days after a hazardous    176.24(b),
     material (or 3 years      177.817(f).
     for a hazardous waste)
     is accepted by the
     initial carrier.
C. Stowage/transportation
 Requirements:
    1. Transporting packages  Various.............  $3,000.
     of hazardous material
     that have not been
     secured against
     movement.
    2. Failure to properly    Various.............  $7,500 and up.
     segregate hazardous
     materials.
    3. Transporting           177.835(i)..........  $5,200.
     explosives in a motor
     vehicle containing
     metal or other articles
     or materials likely to
     damage the explosives
     or any package in which
     they are contained,
     without segregating in
     different parts of the
     load or securing them
     in place in or on the
     motor vehicle and
     separated by bulkheads
     or other suitable means
     to prevent damage.
    4. Transporting railway   171.2(b) & (e)......  $7,000.
     track torpedoes outside
     of flagging kits, in
     violation of DOT-E 7991.
    5. Transporting Class 7   177.842(a)..........  $5,000 and up.
     (radioactive) material
     having a total
     transport index greater
     than 50.
    6. Transporting Class 7   177.842(b)..........  $5,000 and up.
     (radioactive) material
     without maintaining the
     required separation
     distance.
    7. Failure to comply      171.2(b) & (e)......
     with requirements of an
     exemption or special
     permit authorizing the
     transportation of Class
     7 (radioactive)
     material having a total
     transportation index of
     50.
        a. Failure to have    ....................  $5,000.
         the required
         radiation survey
         record.
        b. Failure to have    ....................  $500 each.
         other required
         documents.
        c. Other violations.  ....................  $5,000 and up.
------------------------------------------------------------------------

                III. Consideration of Statutory Criteria

    A. These guidelines are used by the Office of Hazardous Materials 
Safety (OHMS) in setting initial proposed penalties for hazmat 
violations. They indicate baseline amounts or ranges for probable 
violations frequently cited in enforcement reports and set forth general 
OHMS policy for considering statutory criteria.
    B. The initial baseline determination partially considers the 
nature, extent, circumstances, and gravity of the alleged violation. 
That determination then is adjusted to consider all other evidence 
concerning the nature, extent, circumstances, and gravity of the alleged 
violation; degree of culpability; history of prior violations; ability 
to pay; effect of the penalty on ability to continue to do business; and 
such other matters as justice may require (a major component of which is 
corrective action taken by a respondent to prevent a recurrence of 
similar violations). In making a penalty recommendation, the baseline or 
range may be increased or decreased on the basis of evidence pertaining 
to these factors.
    C. The following miscellaneous factors are used to implement one or 
more of the statutory assessment criteria.

           IV. Miscellaneous Factors Affecting Penalty Amounts

                          A. Corrective Action

    1. A proposed penalty is mitigated for documented corrective action 
of alleged violations taken by a respondent. Corrective action may 
occur: (1) After an inspection and before a Notice of Probable Violation 
(NOPV) is issued; (2) on receipt of an NOPV; or (3) after receipt of an 
NOPV (possibly after it is solicited by an PHMSA attorney). In general, 
corrective action may reduce a penalty up to 25%. Mitigation may be 
taken into account in the referral memo or may be recommended prior to 
issuance of an Order by PHMSA's Chief Counsel.
    2. The two primary factors in determining the penalty reduction are 
extent and timing of the corrective action. In other words, mitigation 
will be determined on the basis of how much corrective action was taken 
and when it was taken. Systemic action to prevent future violations is 
given greater consideration than action simply to remedy violations 
identified during the inspection.
    3. Mitigation is applied to individual violations. Thus, in a case 
with two violations, if corrective action for the first violation is 
more extensive than for the second, the penalty for the first will be 
mitigated more than that for the second.

                       B. Respondents That Re-Ship

    A shipper that reships materials received from another company, in 
the same packaging and without opening or altering the package, 
independently is responsible for ensuring that the shipment complies 
with Federal hazmat law, and independently may be subject to enforcement 
action if the package does not comply. Nevertheless, the reshipper is 
considered to have a lesser level of responsibility for compliance in 
those respects in which it reasonably relies on the compliance of the 
package as received. In most cases of

[[Page 52]]

this type, OHMS will discount the applicable baseline standard by about 
25%. The specific knowledge and expertise of all parties must be 
considered in discounting for reliance on a prior shipper. This discount 
is applied before any consideration of mitigation based on corrective 
action.

                C. Penalty Increases for Multiple Counts

    Under the Federal hazmat law, 49 U.S.C. 5123(a), each violation of 
the HMR and each day of a continuing violation (except for violations 
pertaining to packaging manufacture or qualification) is subject to a 
civil penalty of up to $55,000 or $110,000 for a violation occurring on 
or after January 1, 2010. Absent aggravating factors, OHMS, in its 
exercise of discretion, ordinarily will apply a single penalty for 
multiple counts or days of violation. In a number of cases, particularly 
those involving shippers, an inspector may cite two or more similar 
packaging violations for different hazardous materials. For example, the 
inspector may cite the same marking violation for two or more packages. 
OHMS usually will consider those additional violations as counts of the 
same violation and will not recommend multiples of the same baseline 
penalty. Rather, OHMS usually will recommend the baseline penalty for a 
single violation, increased by 25% for each additional violation.

                       D. Financial Considerations

    1. Mitigation is appropriate when the baseline penalty would (1) 
exceed an amount that the respondent is able to pay, or (2) have an 
adverse effect on the respondent's ability to continue in business. 
These criteria relate to a respondent's entire business, and not just 
the product line or part of its operations involved in the violation(s). 
Beyond the overall financial size of the respondent's business, the 
relevant items of information on a respondent's balance sheet include 
the current ratio (current assets to current liabilities), the nature of 
current assets, and net worth (total assets minus total liabilities).
    2. These figures are considered on a case-by-case basis. In general, 
however, a current ratio close to or below 1.0 means that the company 
may have difficulty in paying a large penalty, and may justify reduction 
of the penalty or an installment payment plan. A small amount of cash on 
hand representing limited liquidity, even with substantial other current 
assets (such as accounts receivable or inventory), may warrant a short-
term payment plan. Respondent's income statement also will be reviewed 
to determine whether a payment plan is appropriate.
    3. Many companies are able to continue in business for extended 
periods of time with a small or negative net worth, and many respondents 
have paid substantial civil penalties in installments even though net 
worth was negative. For this reason, negative net worth alone does not 
always warrant reduction of a proposed penalty or even, in the absence 
of factors discussed above, a payment plan.
    4. In general, an installment payment plan may be justified where 
reduction of a proposed penalty is not, but the appropriateness of 
either (or both) will depend on the circumstances of the case. The 
length of a payment plan should be as short as possible, but the plan 
may consider seasonal fluctuations in a company's income if the 
company's business is seasonal (e.g., swimming pool chemical sales, 
fireworks sales) or if the company has documented specific reasons for 
current non-liquidity.
    5. Evidence of financial condition is used only to decrease a 
penalty, and not to increase it.

                E. Penalty Increases for Prior Violations

    The baseline penalty presumes an absence of prior violations. If 
prior violations exist, generally they will serve to increase a proposed 
penalty. The general standards for increasing a baseline proposed 
penalty on the basis of prior violations are as follows:
    1. For each prior civil or criminal enforcement case--25% increase 
over the pre-mitigation recommended penalty.
    2. For each prior ticket--10% increase over the pre-mitigation 
recommended penalty.
    3. A baseline proposed penalty will not be increased more than 100% 
on the basis of prior violations.
    4. A case or ticket of prior violations initiated in a calendar year 
more than six years before the calendar year in which the current case 
is initiated normally will not be considered in determining a proposed 
penalty for the current violation(s).

         F. Penalty Increases for Use of Expired Special Permits

    Adjustments to the base line figures for use of expired special 
permits can be made depending on how much material has been shipped 
during the period between the expiration date and the renewal date. If 
the company previously has been found to have operated under an expired 
special permit, the penalty is normally doubled. If the company has been 
previously cited for other violations, the penalty generally will be 
increased by about 25%.

[Amdt. 107-33, 60 FR 12141, Mar. 6, 1995, as amended by Amdt. 107-40, 62 
FR 2972, 2977, Jan. 21, 1997; 62 FR 51556, Oct. 1, 1997; 65 FR 58618, 
Sept. 29, 2000; 66 FR 45180, Aug. 28, 2001; 68 FR 52848, 52855, Sept. 8, 
2003; 69 FR 54044, Sept. 7, 2004; 70 FR 56090, Sept. 23, 2005; 70 FR 
73162, Dec. 9, 2005; 71 FR 8487, Feb. 17, 2006; 74 FR 53185, Oct. 16, 
2009; 74 FR 68702, Dec. 29, 2009]

[[Page 53]]



      Subpart E_Designation of Approval and Certification Agencies



Sec. 107.401  Purpose and scope.

    (a) This subpart establishes procedures for the designation of 
agencies to issue approval certificates and certifications for types of 
packagings designed, manufactured, tested, or maintained in conformance 
with the requirements of this subchapter, subchapter C of this chapter, 
and standards set forth in the United Nations (U.N.) Recommendations 
(Transport of Dangerous Goods). Except for certifications of compliance 
with U.N. packaging standards, this subpart does not apply unless made 
applicable by a rule in subchapter C of this chapter.
    (b) The Associate Administrator may issue approval certificates and 
certifications addressed in paragraph (a) of this section.

[Amdt. 107-31, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23, 
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]



Sec. 107.402  Application for designation as an approval or certification 

agency.

    (a) Any organization or person seeking designation as an approval or 
certification agency shall apply in writing to the Associate 
Administrator for Hazardous Materials Safety (PHH-32), Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington 
DC 20590-0001. Alternatively, the application with any attached 
supporting documentation in an appropriate format may be submitted by 
facsimile (fax) to: (202) 366-3753 or (202) 366-3308 or by electronic 
mail (e-mail) to: approvals@dot.gov. Each application must be signed and 
certified to be correct by the applicant or, if the applicant is an 
organization, by an authorized officer or official representative of the 
organization. Any false statement or representation, or the knowing and 
willful concealment of a material fact, may subject the applicant to 
prosecution under the provisions of 18 U.S.C. 1001, result in the denial 
or termination of a designation.
    (b) Each application for designation must be in English and include 
the following information:
    (1) Name and address of the applicant, including place of 
incorporation if a corporation. In addition, if the applicant is not a 
resident of the United States, the name and address of a permanent 
resident of the United States designated in accordance with Sec. 105.40 
to serve as agent for service of process.
    (2) If the applicant's principal place of business is in a country 
other than the United States, a copy of the designation from the 
Competent Authority of that country delegating to the applicant an 
approval or designated agency authority for the type of packaging for 
which a DOT designation is sought, and a statement that the Competent 
Authority also delegates similar authority to U.S. Citizens or 
organizations having designations under this subpart from the PHMSA.
    (3) A listing, by DOT specification (or special permit) number, or 
U.N. designation, of the types of packagings for which approval 
authority is sought.
    (4) A personnel qualifications plan listing the qualifications that 
the applicant will require of each person to be used in the performance 
of each packaging approval or certification function. As a minimum, 
these qualifications must include:
    (i) The ability to review and evaluate design drawings, design and 
stress calculations;
    (ii) A knowledge of the applicable regulations of subchapter C of 
this chapter and, when applicable, U.N. standards; and
    (iii) The ability to conduct or monitor and evaluate test procedures 
and results; and
    (iv) The ability to review and evaluate the qualifications of 
materials and fabrication procedures.
    (5) A statement that the applicant will perform its functions 
independent of the manufacturers and owners of the packagings concerned.
    (6) A statement that the applicant will allow the Associate 
Administrator or his representative to inspect its records and 
facilities in so far as they relate to the approval or certification of 
specification packagings and shall cooperate in the conduct of such 
inspections.
    (c) The applicant shall furnish any additional information relevant 
to the

[[Page 54]]

applicant's qualifications, if requested by the Associate Administrator.

[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985; 50 FR 16089, Apr. 24, 1985, 
as amended by Amdt. 107-22, 55 FR 39978, Oct. 1, 1990; Amdt. 107-23, 56 
FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001; 67 FR 61011, Sept. 
27, 2002; 70 FR 56090, Sept. 23, 2005; 72 FR 55683, Oct. 1, 2007]



Sec. 107.403  Designation of approval agencies.

    (a) If the Associate Administrator determines that an application 
contains all the required information, the applicant is sent a letter of 
designation and assigned an identification code.
    (b) If the Associate Administrator determines that an application 
does not contain all the required information, the application is denied 
and the applicant is sent a written notice containing all the reasons 
for the denial.
    (c) Within 30 days of an initial denial of an application under 
paragraph (b) of this section, the applicant may file an amended 
application. If after considering the amended application, the Associate 
Administrator determines that it should be denied, he notifies the 
applicant, and the denial constitutes the final action of the Associate 
Administrator on the application. Within 60 days of receipt of the final 
denial the applicant may appeal the denial to the Administrator, PHMSA, 
setting forth in writing where the Associate Administrator for Hazardous 
Materials Safety erred in this determination.

[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23, 
56 FR 66157, Dec. 20, 1991; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; 
66 FR 45377, Aug. 28, 2001]



Sec. 107.404  Conditions of designation.

    (a) Each designation made under this subpart contains the following 
conditions:
    (1) The designated approval or certification agency may use only 
testing equipment that it has determined, through personal inspection, 
to be suitable for the purpose.
    (2) Each approval certificate and certification issued by the 
designated approval agency must contain the name and identification code 
of the approval agency.
    (3) Each approval certificate and certification must be in a format 
acceptable to the Associate Administrator.
    (b) The designated approval agency shall notify the Associate 
Administrator within 20 days after the date there is any change in the 
information submitted under Sec. 107.402.
    (c) The designated approval agency shall comply with all of the 
terms and conditions stated in its letter of designation under the 
subpart.
    (d) Nothing in this part relieves a manufacturer or owner of a 
packaging of responsibility for compliance with any of the applicable 
requirements of this title.

[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23, 
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]



Sec. 107.405  Termination of designation.

    (a) Any designation issued under Sec. 107.403 of this subchapter 
may be suspended or terminated if the Associate Administrator determines 
that:
    (1) The application for designation contained a misrepresentation, 
or the applicant willfully concealed a material fact.
    (2) The approval agency failed to comply with a term or condition 
stated in the agency's letter of designation.
    (3) The Competent Authority of an approval agency of a country 
outside the United States has failed to initiate, maintain or recognize 
a qualified U.S. approval agency.
    (b) Before a designation is suspended or terminated, the Associate 
Administrator shall give to the approval agency:
    (1) Written notice of the facts or conduct believed to warrant 
suspension or termination of the designation.
    (2) Sixty days in which to show in writing why the designation 
should not be suspended or terminated.

[Amdt. 107-13, 50 FR 10062, Mar. 13, 1985, as amended by Amdt. 107-23, 
56 FR 66157, Dec. 20, 1991; 66 FR 45377, Aug. 28, 2001]

[[Page 55]]



   Subpart F_Registration of Cargo Tank and Cargo Tank Motor Vehicle 

 Manufacturers, Assemblers, Repairers, Inspectors, Testers, and Design 

                          Certifying Engineers



Sec. 107.501  Scope.

    (a) This subpart establishes a registration procedure for persons 
who are engaged in the manufacture, assembly, inspection and testing, 
certification, or repair of a cargo tank or a cargo tank motor vehicle 
manufactured in accordance with a DOT specification under subchapter C 
of this chapter or under terms of a special permit issued under this 
part.
    (b) Persons engaged in continuing qualification and maintenance of 
cargo tanks and cargo tank motor vehicles must be familiar with the 
requirements set forth in part 180, subpart E, of this chapter.

[Amdt. 107-20, 55 FR 37047, Sept. 7, 1990]



Sec. 107.502  General registration requirements.

    (a) Definitions: For purposes of this subpart--
    (1) Assembly means the performance of any of the following functions 
when the function does not involve welding on the cargo tank wall:
    (i) The mounting of one or more tanks or cargo tanks on a motor 
vehicle or to a motor vehicle suspension component;
    (ii) The installation of equipment or components necessary to meet 
the specification requirements prior to the certification of the cargo 
tank motor vehicle; or
    (iii) The installation of linings, coatings, or other materials to 
the inside of a cargo tank wall.
    (2) The terms Authorized Inspector, Cargo tank, Cargo tank motor 
vehicle, Design Certifying Engineer, Registered Inspector, and Person 
are defined in Sec. 171.8 of this chapter.
    (3) The terms cargo tank wall and manufacturer are defined in Sec. 
178.320(a), and repair is defined in Sec. 180.403 of this chapter.
    (b) No person may engage in the manufacture, assembly, 
certification, inspection or repair of a cargo tank or cargo tank motor 
vehicle manufactured under the terms of a DOT specification under 
subchapter C of this chapter or a special permit issued under this part 
unless the person is registered with the Department in accordance with 
the provisions of this subpart. A person employed as an inspector or 
design certifying engineer is considered to be registered if the 
person's employer is registered.
    (c) A person who performs functions which are subject to the 
provisions of this subpart may perform only those functions which have 
been identified to the Department in accordance with the procedures of 
this subpart.
    (d) Registration statements must be in English, contain all of the 
information required by this subpart, and be submitted to: FMCSA 
Hazardous Materials Division--MC-ECH, West Building, MC-ECH, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
    (e) Upon determination that a registration statement contains all 
the information required by this subpart, the Department will send the 
registrant a letter confirming receipt of the registration application 
and assigning a registration number to that person. A separate 
registration number will be assigned for each cargo tank manufacturing, 
assembly, repair facility or other place of business identified by the 
registrant.

[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37047, Sept. 7, 1990, 
as amended by Amdt. 107-22, 55 FR 39978, Oct. 1, 1990; Amdt. 107-23, 56 
FR 66157, Dec. 20, 1991; Amdt. 107-28, 58 FR 46873, Sept. 3, 1993; Amdt. 
107-39, 61 FR 51337, Oct. 1, 1996; 67 FR 61011, Sept. 27, 2002; 68 FR 
19273, Apr. 18, 2003; 72 FR 55683, Oct. 1, 2007]



Sec. 107.503  Registration statement.

    (a) Each registration statement must be in English and contain the 
following information:
    (1) Name;
    (2) Street address, mailing address and telephone number for each 
facility or place of business;
    (3) A statement indicating whether the facility uses mobile testing/
inspection equipment to perform inspections, tests, or repairs at a 
location other than the address listed in paragraph (a)(2) of this 
section.

[[Page 56]]

    (4) A statement signed by the person responsible for compliance with 
the applicable requirements of this chapter, certifying knowledge of 
those requirements and that each employee who is a Registered Inspector 
or Design Certifying Engineer meets the minimum qualification 
requirements set forth in Sec. 171.8 of this chapter for ``Registered 
Inspector'' or ``Design Certifying Engineer''. The following language 
may be used.

    I certify that all Registered Inspectors and Design Certifying 
Engineers used in performance of the prescribed functions meet the 
minimum qualification requirements set forth in 49 CFR 171.8, that I am 
the person responsible for ensuring compliance with the applicable 
requirements of this chapter, and that I have knowledge of the 
requirements applicable to the functions to be performed.

    (5) A description of the specific functions to be performed on cargo 
tanks or cargo tank motor vehicles, e.g.:
    (i) Manufacture,
    (ii) Assembly,
    (iii) Inspection and testing (specify type, e.g., external or 
internal visual inspection, lining inspection, hydrostatic pressure 
test, leakage test, thickness test),
    (iv) Certification,
    (v) Repair, or
    (vi) Equipment manufacture;
    (6) An identification of the types of DOT specification and special 
permit cargo tanks or cargo tank motor vehicles which the registrant 
intends to manufacture, assemble, repair, inspect, test or certify;
    (7) A statement indicating whether the registrant employs Registered 
Inspectors or Design Certifying Engineers to conduct certification, 
inspection or testing functions addressed by this subpart. If the 
registrant engages a person who is not an employee of the registrant to 
perform these functions, provide the name, address and registration 
number of that person; and
    (8) If the registrant is not a resident of the United States, the 
name and address of a permanent resident of the United States designated 
in accordance with Sec. 105.40 to serve as agent for service of 
process.
    (b) In addition to the information required under paragraph (a) of 
this section, each person who manufactures a cargo tank or cargo tank 
motor vehicle must submit a copy of the manufacturer's current ASME 
Certificate of Authorization for the use of the ASME ``U'' stamp.
    (c) In addition to the information required under paragraph (a) of 
this section, each person who repairs a cargo tank or cargo tank motor 
vehicle must submit a copy of the repair facility's current National 
Board Certificate of Authorization for the use of the ``R'' stamp or 
ASME Certificate of Authorization for the use of the ASME ``U'' stamp. 
Any person who repairs MC-series cargo tanks which are not certified to 
the ASME Code must submit a copy of the National Board or ASME 
Certificate of Authorization to PHMSA before June 30, 1992.

[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37047, Sept. 7, 1990; 
57 FR 365, Jan. 6, 1992; Amdt. 107-32, 59 FR 49131, Sept. 26, 1994; 
Amdt. 107-39, 61 FR 51337, Oct. 1, 1996; 63 FR 52846, Oct. 1, 1998; 68 
FR 19273, Apr. 18, 2003]



Sec. 107.504  Period of registration, updates, and record retention.

    (a) Registration will be for a maximum of six years from the date of 
the original registration.
    (b) Any correspondence with the Department must contain the 
registrant's name and registration number.
    (c) A registration must be renewed every six years or within thirty 
days of reissuance of an ASME or National Board Certification, whichever 
occurs first, by submitting an up-to-date registration statement 
containing the information prescribed by Sec. 107.503. Any person 
initially registered under the provisions of Sec. 107.502 and who is in 
good standing is eligible for renewal.
    (d) A registrant shall provide written notification to the 
Department within thirty days of any of the following occurrences:
    (1) Any change in the registration information submitted under Sec. 
107.503;
    (2) Replacement of the person responsible for compliance with the 
requirements in Sec. 107.503(a)(4). If this occurs, the registrant 
shall resubmit the required certification;
    (3) Loss of ASME or National Board Certificate of Authorization; or

[[Page 57]]

    (4) A change in function; such as, from assembly to manufacture, an 
addition of a function, or a change to the types of inspections, tests 
or certifications of cargo tanks or cargo tank motor vehicles.
    (e) Each registrant shall maintain a current copy of the 
registration information submitted to the Department and a current copy 
of the registration number identification received from the Department 
at the location identified in Sec. 107.503(a)(2) during such time the 
person is registered with the Department and for two years thereafter.
    (f) The issuance of a registration number under this subpart is not 
an approval or endorsement by the Department of the qualifications of 
any person to perform the specified functions.

[Amdt. 107-20, 54 FR 25003, June 12, 1989; 55 FR 37048, Sept. 7, 1990, 
as amended by Amdt. 107-20, 56 FR 27875, June 17, 1991; Amdt. 107-37, 61 
FR 18931, Apr. 29, 1996; 71 FR 54390, Sept. 14, 2006]



   Subpart G_Registration of Persons Who Offer or Transport Hazardous 

                                Materials

    Source: Amdt. No. 107-26, 57 FR 30630, July 9, 1992, unless 
otherwise noted.



Sec. 107.601  Applicability.

    (a) The registration and fee requirements of this subpart apply to 
any person who offers for transportation, or transports, in foreign, 
interstate or intrastate commerce--
    (1) A highway route-controlled quantity of a Class 7 (radioactive) 
material, as defined in Sec. 173.403 of this chapter;
    (2) More than 25 kg (55 pounds) of a Division 1.1, 1.2, or 1.3 
(explosive) material (see Sec. 173.50 of this chapter) in a motor 
vehicle, rail car or freight container;
    (3) More than one L (1.06 quarts) per package of a material 
extremely toxic by inhalation (i.e., ``material poisonous by 
inhalation,'' as defined in Sec. 171.8 of this chapter, that meets the 
criteria for ``hazard zone A,'' as specified in Sec. Sec. 173.116(a) or 
173.133(a) of this chapter);
    (4) A shipment of a quantity of hazardous materials in a bulk 
packaging (see Sec. 171.8 of this chapter) having a capacity equal to 
or greater than 13,248 L (3,500 gallons) for liquids or gases or more 
than 13.24 cubic meters (468 cubic feet) for solids;
    (5) A shipment in other than a bulk packaging of 2,268 kg (5,000 
pounds) gross weight or more of one class of hazardous materials for 
which placarding of a vehicle, rail car, or freight container is 
required for that class, under the provisions of subpart F of part 172 
of this chapter; or
    (6) Except as provided in paragraph (b) of this section, a quantity 
of hazardous material that requires placarding, under provisions of 
subpart F of part 172 of this chapter.
    (b) Paragraph (a)(6) of this section does not apply to those 
activities of a farmer, as defined in Sec. 171.8 of this chapter, that 
are in direct support of the farmer's farming operations.
    (c) In this subpart, the term ``shipment'' means the offering or 
loading of hazardous material at one loading facility using one 
transport vehicle, or the transport of that transport vehicle.

[65 FR 7309, Feb. 14, 2000, as amended at 67 FR 61011, Sept. 27, 2002]



Sec. 107.606  Exceptions.

    (a) The following are excepted from the requirements of this 
subpart:
    (1) An agency of the Federal government.
    (2) A State agency.
    (3) An agency of a political subdivision of a State.
    (4) An Indian tribe.
    (5) An employee of any of those entities in paragraphs (a)(1) 
through (a)(4) of this section with respect to the employee's official 
duties.
    (6) A hazmat employee (including, for purposes of this subpart, the 
owner-operator of a motor vehicle that transports in commerce hazardous 
materials, if that vehicle at the time of those activities, is leased to 
a registered motor carrier under a 30-day or longer lease as prescribed 
in 49 CFR part 376 or an equivalent contractual agreement).
    (7) A person domiciled outside the United States, who offers solely 
from a location outside the United States, hazardous materials for 
transportation in commerce, provided that the country of which such a 
person is a domiciliary does not require persons domiciled in

[[Page 58]]

the United States, who solely offer hazardous materials for 
transportation to the foreign country from places in the United States, 
to file a registration statement or to pay a registration fee.
    (b) Upon making a determination that persons domiciled in the United 
States, who offer hazardous materials for transportation to a foreign 
country solely from places in the United States, must file registration 
statements or pay fees to that foreign country, the U.S. Competent 
Authority will provide notice of such determination directly to the 
Competent Authority of that foreign country and by publication in the 
Federal Register. Persons who offer hazardous materials for 
transportation to the United States from that foreign country must file 
a registration statement and pay the required fee no later than 60 days 
following publication of the determination in the Federal Register.

[Amdt 107-34, 60 FR 27233, May 23, 1995, as amended at 63 FR 52847, Oct. 
1, 1998; 72 FR 24538, May 3, 2007]



Sec. 107.608  General registration requirements.

    (a) Each person subject to this subpart must submit a complete and 
accurate registration statement on DOT Form F 5800.2 not later than June 
30 for each registration year, or in time to comply with paragraph (b) 
of this section, whichever is later. Each registration year begins on 
July 1 and ends on June 30 of the following year.
    (b) No person required to file a registration statement may 
transport a hazardous material or cause a hazardous material to be 
transported or shipped, unless such person has on file, in accordance 
with Sec. 107.620, a current Certificate of Registration in accordance 
with the requirements of this subpart.
    (c) A registrant whose name or principal place of business has 
changed during the year of registration must notify PHMSA of that change 
by submitting an amended registration statement not later than 30 days 
after the change.
    (d) Copies of DOT Form F 5800.2 and instructions for its completion 
may be obtained from the Outreach, Training and Grants Division, PHH-50, 
U.S. Department of Transportation, Washington, DC 20590-0001, by calling 
202-366-4109, or via the Internet at http://phmsa.dot.gov/hazmat/
registration.
    (e) If the registrant is not a resident of the United States, the 
registrant must attach to the registration statement the name and 
address of a permanent resident of the United States, designated in 
accordance with Sec. 105.40, to serve as agent for service of process.

[Amdt. No. 107-26, 57 FR 30630, July 9, 1992, as amended by Amdt. 107-
31, 59 FR 32932, June 27, 1994; 65 FR 7309, Feb. 14, 2000; 67 FR 61011, 
Sept. 27, 2002; 70 FR 56090, Sept. 23, 2005; 72 FR 55683, Oct. 1, 2007; 
76 FR 56311, Sept. 13, 2011]



Sec. 107.612  Amount of fee.

    (a) For the registration year 2010-2011 and subsequent years, each 
person offering for transportation or transporting in commerce a 
material listed in Sec. 107.601(a) must pay an annual registration fee, 
as follows:
    (1) Small business. Each person that qualifies as a small business, 
under criteria specified in 13 CFR part 121 applicable to the North 
American Industry Classification System (NAICS) code that describes that 
person's primary commercial activity, must pay an annual registration 
fee of $250 and the processing fee required by paragraph (a)(4) of this 
section.
    (2) Not-for-profit organization. Each not-for-profit organization 
must pay an annual registration fee of $250 and the processing fee 
required by paragraph (a)(4) of this section. A not-for-profit 
organization is an organization exempt from taxation under 26 U.S.C. 
501(a).
    (3) Other than a small business or not-for-profit organization. Each 
person that does not meet the criteria specified in paragraph (a)(1) or 
(a)(2) of this section must pay an annual registration fee of $2,575 and 
the processing fee required by paragraph (a)(4) of this section.
    (4) Processing fee. The processing fee is $25 for each registration 
statement filed. A single statement may be filed for one, two, or three 
registration years as provided in Sec. 107.616(c).
    (b) For registration years 2009-2010 and prior years, each person 
that offered for transportation or transported in commerce a material 
listed in Sec. 107.601(a) during that year must pay

[[Page 59]]

the annual registration fee, including the processing fee, specified 
under the requirements of this subchapter in effect for the specific 
registration year.
    (c) Registration years 2003-2004, 2004-2005 and 2005-2006. For 
registration years 2003-2004, 2004-2005, and 2005-2006, each person 
subject to the requirements of this subpart must pay an annual 
registration fee as follows:
    (1) Small business. Each person that qualifies as a small business, 
under criteria specified in 13 CFR part 121 applicable to the North 
American Industry Classification System (NAICS) code that describes that 
person's primary commercial activity, must pay an annual registration 
fee of $125 and the processing fee required by paragraph (c)(4) of this 
section.
    (2) Not-for-profit organization. Each not-for-profit organization 
must pay an annual registration fee of $125 and the processing fee 
required by paragraph (c)(4) of this section. A not-for-profit 
organization is an organization exempt from taxation under 26 U.S.C. 
501(a).
    (3) Other than a small business or not-for-profit organization. Each 
person that does not meet the criteria specified in paragraph (c)(1) or 
(c)(2) of this section must pay an annual registration fee of $275 and 
the processing fee required by paragraph (c)(4) of this section.
    (4) Processing fee. The processing fee is $25 for each registration 
statement filed. A single statement may be filed for one, two, or three 
registration years as provided in Sec. 107.616(c).
    (d) Registration years 2006-2007 and following. For each 
registration year beginning with 2006-2007, each person subject to the 
requirements of this subpart must pay an annual fee as follows:
    (1) Small business. Each person that qualifies as a small business, 
under criteria specified in 13 CFR part 121 applicable to the North 
American Industry Classification System (NAICS) code that describes that 
person's primary commercial activity, must pay an annual registration 
fee of $250 and the processing fee required by paragraph (d)(4) of this 
section.
    (2) Not-for-profit organization. Each not-for-profit organization 
must pay an annual registration fee of $250 and the processing fee 
required by paragraph (d)(4) of this section. A not-for-profit 
organization is an organization exempt from taxation under 26 U.S.C. 
501(a).
    (3) Other than a small business or not-for-profit organization. Each 
person that does not meet the criteria specified in paragraph (d)(1) or 
(d)(2) of this section must pay an annual registration fee of $975 and 
the processing fee required by paragraph (d)(4) of this section.
    (4) Processing fee. The processing fee is $25 for each registration 
statement filed. A single statement may be filed for one, two, or three 
registration years as provided in Sec. 107.616(c).

[65 FR 7309, Feb. 14, 2000, as amended at 67 FR 58345, Sept. 16, 2002; 
68 FR 1345, Jan. 9, 2003; 75 FR 15619, Mar. 30, 2010]



Sec. 107.616  Payment procedures.

    (a) Each person subject to the requirements of this subpart must 
mail the registration statement and payment in full to the U.S. 
Department of Transportation, Hazardous Materials Registration, P.O. Box 
530273, Atlanta, GA 30353-0273, or submit the statement and payment 
electronically through the Department's e-Commerce Internet site. Access 
to this service is provided at http://phmsa.dot.gov/hazmat/registration. 
A registrant required to file an amended registration statement under 
Sec. 107.608(c) must mail it to the same address or submit it through 
the same Internet site.
    (b) Payment must be made by certified check, cashier's check, 
personal check, or money order in U.S. funds and drawn on a U.S. bank, 
payable to the U.S. Department of Transportation and identified as 
payment for the ``Hazmat Registration Fee,'' or by completing an 
authorization for payment by credit card or other electronic means of 
payment acceptable to the Department on the registration statement or as 
part of an Internet registration as provided in paragraph (a) of this 
section.
    (c) Payment must correspond to the total fees properly calculated in 
the ``Amount Due'' block of the DOT form F 5800.2. A person may elect to 
register and pay the required fees for up to three registration years by 
filing one

[[Page 60]]

complete and accurate registration statement.

[Amdt. 107-26, 57 FR 30630, July 9, 1992, as amended by Amdt. 107-26, 58 
FR 12545, Mar. 5, 1993; 65 FR 7310, Feb. 14, 2000; 67 FR 58345, Sept. 
16, 2002; 68 FR 1346, Jan. 9, 2003; 71 FR 54390, Sept. 14, 2006; 72 FR 
24538, May 3, 2007; 76 FR 56311, Sept. 13, 2011]



Sec. 107.620  Recordkeeping requirements.

    (a) Each person subject to the requirements of this subpart, or its 
agent designated under Sec. 107.608(e), must maintain at its principal 
place of business for a period of three years from the date of issuance 
of each Certificate of Registration:
    (1) A copy of the registration statement filed with PHMSA; and
    (2) The Certificate of Registration issued to the registrant by 
PHMSA.
    (b) After January 1, 1993, each motor carrier subject to the 
requirements of this subpart must carry a copy of its current 
Certificate of Registration issued by PHMSA or another document bearing 
the registration number identified as the ``U.S. DOT Hazmat Reg. No.'' 
on board each truck and truck tractor (not including trailers and semi-
trailers) used to transport hazardous materials subject to the 
requirements of this subpart. The Certificate of Registration or 
document bearing the registration number must be made available, upon 
request, to enforcement personnel.
    (c) In addition to the requirements of paragraph (a) of this 
section, after January 1, 1995, each person who transports by vessel a 
hazardous material subject to the requirements of this subpart must 
carry on board the vessel a copy of its current Certificate of 
Registration or another document bearing the current registration number 
identified as the ``U.S. DOT Hazmat Reg. No.''
    (d) Each person subject to this subpart must furnish its Certificate 
of Registration (or a copy thereof) and all other records and 
information pertaining to the information contained in the registration 
statement to an authorized representative or special agent of DOT upon 
request.

[Amdt. No. 107-26, 57 FR 30630, July 9, 1992, as amended at 57 FR 37902, 
August 21, 1992; Amdt. 107-26, 58 FR 12545, Mar. 5, 1993; Amdt. 107-31, 
59 FR 32932, June 27, 1994]



           Subpart H_Approvals, Registrations and Submissions

    Source: Amdt. 107-38, 61 FR 21100, May 9, 1996, unless otherwise 
noted.



Sec. 107.701  Purpose and scope.

    (a) This subpart prescribes procedures for the issuance, 
modification and termination of approvals, and the submission of 
registrations and reports, as required by this chapter.
    (b) The procedures of this subpart are in addition to any 
requirements in subchapter C of this chapter applicable to a specific 
approval, registration or report. If compliance with both a specific 
requirement of subchapter C of this chapter and a procedure of this 
subpart is not possible, the specific requirement applies.
    (c) Registration under subpart F or G of this part is not subject to 
the procedures of this subpart.

[Amdt. 107-38, 61 FR 21100, May 9, 1996; Amdt. 107-38, 61 FR 27948, June 
3, 1996]



Sec. 107.705  Registrations, reports, and applications for approval.

    (a) A person filing a registration, report, or application for an 
approval, or a renewal or modification of an approval subject to the 
provisions of this subpart must--
    (1) File the registration, report, or application with the Associate 
Administrator for Hazardous Materials Safety (Attention: Approvals, PHH-
32), Pipeline and Hazardous Materials Safety Administration, U.S. 
Department of Transportation, East Building, 1200 New Jersey Avenue, 
SE., Washington, DC 20590-0001. Alternatively, the document with any 
attached supporting documentation in an appropriate format may be filed 
by facsimile (fax) to: (202) 366-3753 or (202) 366-3308 or by electronic 
mail (e-mail) to: approvals@dot.gov.

[[Page 61]]

    (2) Identify the section of the chapter under which the 
registration, report, or application is made;
    (3) If a report is required by an approval, a registration or a 
special permit, identify the approval, registration or special permit 
number;
    (4) Provide the name, street and mailing addresses, e-mail address 
optional, and telephone number of the person on whose behalf the 
registration, report, or application is made and, if different, the 
person making the filing;
    (5) If the person on whose behalf the filing is made is not a 
resident of the United States, provide a designation of agent for 
service in accordance with Sec. 105.40;
    (6) Provide a description of the activity for which the registration 
or report is required; and
    (7) Provide additional information as requested by the Associate 
Administrator, if the Associate Administrator determines that a filing 
lacks pertinent information or otherwise does not comply with applicable 
requirements.
    (b) In addition to the provisions in paragraph (a) for an approval, 
an application for an approval, or an application for modification or 
renewal of an approval, the applicant must provide--
    (1) A description of the activity for which the approval is 
required;
    (2) The proposed duration of the approval;
    (3) The transport mode or modes affected, as applicable;
    (4) Any additional information specified in the section containing 
the approval; and
    (5) For an approval which provides exceptions from regulatory 
requirements or prohibitions--
    (i) Identification of any increased risk to safety or property that 
may result if the approval is granted, and specification of the measures 
that the applicant considers necessary or appropriate to address that 
risk; and
    (ii) Substantiation, with applicable analyses or evaluations, if 
appropriate, demonstrating that the proposed activity will achieve a 
level of safety that is at least equal to that required by the 
regulation.
    (c) For an approval with an expiration date, each application for 
renewal or modification must be filed in the same manner as an original 
application. If a complete and conforming renewal application is filed 
at least 60 days before the expiration date of an approval, the 
Associate Administrator, on written request from the applicant, will 
issue a written extension to permit operation under the terms of the 
expired approval until a final decision on the application for renewal 
has been made. Operation under an expired approval is prohibited absent 
a written extension. This paragraph does not limit the authority of the 
Associate Administrator to modify, suspend or terminate an approval 
under Sec. 107.713.
    (d) To request confidential treatment for information contained in 
the application, the applicant shall comply with Sec. 105.30(a).

[Amdt. 107-38, 61 FR 21100, May 9, 1996, as amended at 65 FR 50457, Aug. 
18, 2000; 67 FR 61011, Sept. 27, 2002; 70 FR 56090, Sept. 23, 2005; 70 
FR 73162, Dec. 9, 2005; 72 FR 55683, Oct. 1, 2007]



Sec. 107.709  Processing of an application for approval, including an 

application for renewal or modification.

    (a) No public hearing or other formal proceeding is required under 
this subpart before the disposition of an application.
    (b) At any time during the processing of an application, the 
Associate Administrator may request additional information from the 
applicant. If the applicant does not respond to a written request for 
additional information within 30 days of the date the request was 
received, the application may be deemed incomplete and denied. However, 
if the applicant responds in writing within the 30-day period requesting 
an additional 30 days within which it will gather the requested 
information, the Associate Administrator may grant the 30-day extension.
    (c) The Associate Administrator may grant or deny an application, in 
whole or in part. At the Associate Administrator's discretion, an 
application may be granted subject to provisions that are appropriate to 
protect health, safety and property. The Associate Administrator may 
impose additional provisions not specified in the application,

[[Page 62]]

or delete conditions in the application which are unnecessary.
    (d) The Associate Administrator may grant an application on finding 
that--
    (1) The application complies with this subpart;
    (2) The application demonstrates that the proposed activity will 
achieve a level of safety that--
    (i) Is at least equal to that required by the regulation, or
    (ii) If the regulations do not establish a level of safety, is 
consistent with the public interest and adequately will protect against 
the risks to life and property inherent in the transportation of 
hazardous materials in commerce;
    (3) The application states all material facts, and contains no 
materially false or materially misleading statement;
    (4) The applicant meets the qualifications required by applicable 
regulations; and
    (5) The applicant is fit to conduct the activity authorized by the 
approval, or renewal or modification of approval. This assessment may be 
based on information in the application, prior compliance history of the 
applicant, and other information available to the Associate 
Administrator.
    (e) Unless otherwise specified in this chapter or by the Associate 
Administrator, an approval in which a term is not specified does not 
expire.
    (f) The Associate Administrator notifies the applicant in writing of 
the decision on the application. A denial contains a brief statement of 
reasons.



Sec. 107.711  Withdrawal.

    An application may be withdrawn at any time before a decision to 
grant or deny it is made. Withdrawal of an application does not 
authorize the removal of any related records from the PHMSA dockets or 
files. Applications that are eligible for confidential treatment under 
Sec. 105.30 will remain confidential after the application is 
withdrawn. The duration of this confidential treatment for trade secrets 
and commercial or financial information is indefinite, unless the party 
requesting the confidential treatment of the materials notifies the 
Associate Administrator that the confidential treatment is no longer 
required.

[Amdt. 107-38, 61 FR 21100, May 9, 1996, as amended at 67 FR 61011, 
Sept. 27, 2002]



Sec. 107.713  Approval modification, suspension or termination.

    (a) The Associate Administrator may modify an approval on finding 
that--
    (1) Modification is necessary to conform an existing approval to 
relevant statutes and regulations as they may be amended from time to 
time; or
    (2) Modification is required by changed circumstances to enable the 
approval to continue to meet the standards of Sec. 107.709(d).
    (b) The Associate Administrator may modify, suspend or terminate an 
approval, as appropriate, on finding that--
    (1) Because of a change in circumstances, the approval no longer is 
needed or no longer would be granted if applied for;
    (2) The application contained inaccurate or incomplete information, 
and the approval would not have been granted had the application been 
accurate and complete;
    (3) The application contained deliberately inaccurate or incomplete 
information; or
    (4) The holder knowingly has violated the terms of the approval or 
an applicable requirement of this chapter in a manner demonstrating lack 
of fitness to conduct the activity for which the approval is required.
    (c) Except as provided in paragraph (d) of this section, before an 
approval is modified, suspended or terminated, the Associate 
Administrator notifies the holder in writing of the proposed action and 
the reasons for it, and provides an opportunity to show cause why the 
proposed action should not be taken.
    (1) The holder may file a written response with the Associate 
Administrator within 30 days of receipt of notice of the proposed 
action.
    (2) After considering the holder's or party's written response, or 
after 30 days have passed without response since receipt of the notice, 
the Associate Administrator notifies the holder in writing of the final 
decision with a brief statement of reasons.

[[Page 63]]

    (d) The Associate Administrator, if necessary to avoid a risk of 
significant harm to persons or property, may in the notification declare 
the proposed action immediately effective.



Sec. 107.715  Reconsideration.

    (a) An applicant or a holder may request that the Associate 
Administrator reconsider a decision under Sec. 107.709(f) or Sec. 
107.713(c). The request must:
    (1) Be in writing and filed within 20 days of receipt of the 
decision;
    (2) State in detail any alleged errors of fact and law;
    (3) Enclose any additional information needed to support the request 
to reconsider; and
    (4) State in detail the modification of the final decision sought.
    (b) The Associate Administrator considers newly submitted 
information on a showing that the information could not reasonably have 
been submitted during application processing.
    (c) The Associate Administrator grants or denies, in whole or in 
part, the relief requested and informs the requesting person in writing 
of the decision.



Sec. 107.717  Appeal.

    (a) A person who requested reconsideration under Sec. 107.715 may 
appeal to the Administrator the Associate Administrator's decision on 
the request. The appeal must:
    (1) Be in writing and filed within 30 days of receipt of the 
Associate Administrator's decision on reconsideration;
    (2) State in detail any alleged errors of fact and law;
    (3) Enclose any additional information needed to support the appeal; 
and
    (4) State in detail the modification of the final decision sought.
    (b) The Administrator, if necessary to avoid a risk of significant 
harm to persons or property, may declare the Associate Administrator's 
action effective pending a decision on appeal.
    (c) The Administrator grants or denies, in whole or in part, the 
relief requested and informs the appellant in writing of the decision on 
appeal. The Administrator's decision on appeal is the final 
administrative action.



    Subpart I_Approval of Independent Inspection Agencies, Cylinder 

   Requalifiers, and Non-domestic Chemical Analyses and Tests of DOT 

                         Specification Cylinders

    Source: 67 FR 51639, Aug. 8, 2002, unless otherwise noted.



Sec. 107.801  Purpose and scope.

    (a) This subpart prescribes procedures for--
    (1) A person who seeks approval to be an independent inspection 
agency to perform tests, inspections, verifications and certifications 
of DOT specification cylinders or UN pressure receptacles as required by 
parts 178 and 180 of this chapter;
    (2) A person who seeks approval to engage in the requalification 
(e.g. inspection, testing, or certification), rebuilding, or repair of a 
cylinder manufactured in accordance with a DOT specification or a 
pressure receptacle in accordance with a UN standard, under subchapter C 
of this chapter or under the terms of a special permit issued under this 
part;
    (3) A person who seeks approval to perform the manufacturing 
chemical analyses and tests of DOT specification cylinders, special 
permit cylinders, or UN pressure receptacles outside the United States.
    (b) No person may engage in a function identified in paragraph (a) 
of this section unless approved by the Associate Administratior in 
accordance with the provisions of this subpart. Each person must comply 
with the applicable requirements in this subpart. In addition, the 
procedural requirements in subpart H of this part apply to the filing, 
processing, and termination of an approval issued under this subpart.

[67 FR 51639, Aug. 8, 2002, as amended at 71 FR 33873, June 12, 2006]



Sec. 107.803  Approval of an independent inspection agency (IIA).

    (a) General. Prior to performing cylinder inspections and 
verifications required by parts 178 and 180 of this chapter, a person 
must apply to the Associate Administrator for an approval as

[[Page 64]]

an independent inspection agency. A person approved as an independent 
inspection agency is not an PHMSA agent or representative.
    (b) Criteria. No applicant for approval as an independent inspection 
agency may be engaged in the manufacture of cylinders for use in the 
transportation of hazardous materials, or be directly or indirectly 
controlled by, or have a financial involvement with, any entity that 
manufactures cylinders for use in the transportation of hazardous 
materials, except for providing services as an independent inspector.
    (c) Application information. Each applicant must submit an 
application in conformance with Sec. 107.705 containing the information 
prescribed in Sec. 107.705(a). In addition, the application must 
contain the following information:
    (1) Name and address of each facility where tests and inspections 
are to be performed.
    (2) Detailed description of the inspection and testing facilities to 
be used by the applicant.
    (3) Detailed description of the applicant's qualifications and 
ability to perform the inspections and to verify the inspections 
required by part 178 of this chapter or under the terms of a special 
permit issued under this part.
    (4) Name, address, and principal business activity of each person 
having any direct or indirect ownership interest in the applicant 
greater than three percent and any direct or indirect ownership interest 
in each subsidiary or division of the applicant.
    (5) Name of each individual whom the applicant proposes to employ as 
an inspector and who will be responsible for certifying inspection and 
test results, and a statement of that person's qualifications.
    (6) An identification or qualification number assigned to each 
inspector who is supervised by a certifying inspector identified in 
paragraph (c)(3) of this section.
    (7) A statement that the applicant will perform its functions 
independent of the manufacturers and owners of the cylinders.
    (8) If the applicant's principal place of business is in a country 
other than the United States, the Associate Administrator may approve 
the applicant on the basis of an approval issued by the Competent 
Authority of the country of manufacture. The Competent Authority must 
maintain a current listing of approved IIAs and their identification 
marks. The applicant must provide a copy of the designation from the 
Competent Authority of that country delegating to the applicant an 
approval or designated agency authority for the type of packaging for 
which a DOT or UN designation is sought; and
    (9) The signature of the person certifying the approval application 
and the date on which it was signed.
    (d) Facility inspection. Upon the request of the Associate 
Administrator, the applicant must allow the Associate Administrator or 
the Associate Administrator's designee to inspect the applicant's 
facilities and records. The person seeking approval must bear the cost 
of the inspection.
    (e) After approval, the Associate Administrator may authorize, upon 
request, the independent inspection agency to perform other inspections 
and functions for which the Associate Administrator finds the applicant 
to be qualified. Such additional authorizations will be noted on each 
inspection agency's approval documents.

[67 FR 51639, Aug. 8, 2002, as amended at 68 FR 24659, May 8, 2003; 71 
FR 33873, June 12, 2006]



Sec. 107.805  Approval of cylinder and pressure receptacle requalifiers.

    (a) General. A person must meet the requirements of this section to 
be approved to inspect, test, certify, repair, or rebuild a cylinder in 
accordance with a DOT specification or a UN pressure receptacle under 
subpart C of part 178 or subpart C of part 180 of this chapter, or under 
the terms of a special permit issued under this part.
    (b) Independent Inspection Agency Review. Each applicant must 
arrange for an independent inspection agency, approved by the Associate 
Administrator pursuant to this subpart, to perform a review of its 
inspection or requalification operation. The person seeking approval 
must bear the cost of the inspection. A list of approved independent 
inspection agencies is available from the Associate Administrator at the 
address

[[Page 65]]

listed in Sec. 107.705. Assistance in obtaining an approval is 
available from the same address.
    (c) Application for approval. If the inspection performed by an 
independent inspection agency is completed with satisfactory results, 
the applicant must submit a letter of recommendation from the 
independent inspection agency, an inspection report, and an application 
containing the information prescribed in Sec. 107.705(a). In addition, 
the application must contain--
    (1) The name of the facility manager;
    (2) The types of DOT specification or special permit cylinders, or 
UN pressure receptacles that will be inspected, tested, repaired, or 
rebuilt at the facility;
    (3) A certification that the facility will operate in compliance 
with the applicable requirements of subchapter C of this chapter; and
    (4) The signature of the person making the certification and the 
date on which it was signed.
    (d) Issuance of requalifier identification number (RIN). The 
Associate Administrator issues a RIN as evidence of approval to 
requalify DOT specification or special permit cylinders, or UN pressure 
receptacles if it is determined, based on the applicant's submission and 
other available information, that the applicant's qualifications and, 
when applicable, facility are adequate to perform the requested 
functions in accordance with the criteria prescribed in subpart C of 
part 180 of this subchapter.
    (e) Expiration of RIN. Unless otherwise provided in the issuance 
letter, an approval expires five years from the date of issuance, 
provided the applicant's facility and qualifications are maintained at 
or above the level observed at the time of inspection by the independent 
inspection agency, or at the date of the certification in the 
application for approval for requalifiers only performing inspections 
made under Sec. 180.209(g) of this chapter.
    (f) Exceptions. Notwithstanding the requirements in paragraphs (b) 
and (c) of this section, a person who only performs inspections in 
accordance with Sec. 180.209(g) of this chapter may submit an 
application that, in addition to the information prescribed in Sec. 
107.705(a), identifies the DOT specification/special permit cylinders to 
be inspected; certifies the requalifier will operate in compliance with 
the applicable requirements of subchapter C of this chapter; certifies 
the persons performing inspections have been trained and have the 
information contained in each applicable CGA pamphlet incorporated by 
reference in Sec. 171.7 of this chapter applicable to the requalifiers' 
activities; and includes the signature of the person making the 
certification and the date on which it was signed. Each person must 
comply with the applicable requirements in this subpart. In addition, 
the procedural requirements in subpart H of this part apply to the 
filing, processing and termination of an approval issued under this 
subpart. No person may requalify a DOT specification/special permit 
cylinder in accordance with Sec. 180.209(g) of this chapter unless that 
person has been issued a RIN as provided in paragraph (d) of this 
section.
    (g) Each holder of a current RIN shall report in writing any change 
in its name, address, ownership, testing equipment, or management or 
personnel performing any function under this section, to the Associate 
Administrator (PHH-32) within 20 days of the change.

[67 FR 51639, Aug. 8, 2002, as amended at 68 FR 24659, May 8, 2003; 68 
FR 55544, Sept. 26, 2003; 70 FR 56090, Sept. 23, 2005; 70 FR 73162, Dec. 
9, 2005; 71 FR 33873, June 12, 2006; 76 FR 56311, Sept. 13, 2011]



Sec. 107.807  Approval of non-domestic chemical analyses and tests.

    (a) General. A person who seeks to manufacture DOT specification or 
special permit cylinders outside the United States must seek an approval 
from the Associate Administrator to perform the chemical analyses and 
tests of those cylinders outside the United States.
    (b) Application for approval. Each applicant must submit an 
application containing the information prescribed in Sec. 107.705(a). 
In addition, the application must contain--
    (1) The name, address, and a description of each facility at which 
cylinders are to be manufactured and chemical analyses and tests are to 
be performed;

[[Page 66]]

    (2) Complete details concerning the dimensions, materials of 
construction, wall thickness, water capacity, shape, type of joints, 
location and size of openings and other pertinent physical 
characteristics of each specification or special permit cylinder for 
which approval is being requested, including calculations for cylinder 
wall stress and wall thickness, which may be shown on a drawing or on 
separate sheets attached to a descriptive drawing;
    (3) The name of the independent inspection agency to be used; and
    (4) The signature of the person making the certification and the 
date on which it was signed.
    (c) Facility inspections. Upon the request of the Associate 
Administrator, the applicant must allow the Associate Administrator or 
the Associate Administrator's designee to inspect the applicant's 
cylinder manufacturing and testing facilities and records, and must 
provide such materials and cylinders for analyses and tests as the 
Associate Administrator may specify. The applicant or holder must bear 
the cost of the initial and subsequent inspections, analyses, and tests.



Sec. 107.809  Conditions of UN pressure receptacle approvals.

    (a) Each approval issued under this subpart contains the following 
conditions:
    (1) Upon the request of the Associate Administrator, the applicant 
or holder must allow the Associate Administrator or the Associate 
Administrator's designee to inspect the applicant's pressure receptacle 
manufacturing and testing facilities and records, and must provide such 
materials and pressure receptacles for analyses and tests as the 
Associate Administrator may specify. The applicant or holder must bear 
the cost of the initial and subsequent inspections, analyses, and tests.
    (2) Each holder must comply with all of the terms and conditions 
stated in the approval letter issued under this subpart.
    (b) In addition to the conditions specified in Sec. 107.713, an 
approval may be denied or if issued, suspended or terminated if the 
Competent Authority of the country of manufacture fails to initiate, 
maintain or recognize an IIA approved under this subpart; fails to 
recognize UN standard packagings manufactured in accordance with this 
subchapter; or implements a condition or limitation on United States 
citizens or organizations that is not required of its own citizenry.

[71 FR 33874, June 12, 2006]



PART 109_DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS PROCEDURAL 

REGULATIONS FOR OPENING OF PACKAGES, EMERGENCY ORDERS, AND EMERGENCY RECALLS--

Table of Contents



                          Subpart A_Definitions

Sec.
109.1 Definitions.

                Subpart B_Inspections and investigations

109.3 Inspections and investigations.
109.5 Opening of packages.
109.7 Removal from transportation.
109.9 Transportation for examination and analysis.
109.11 Assistance of properly qualified personnel.
109.13 Closing packages/safe resumption of transportation.
109.15 Termination.

                       Subpart C_Emergency Orders

109.17 Emergency orders.
109.19 Petitions for review of emergency orders.
109.21 Remedies generally.

    Authority: 49 U.S.C. Sec. Sec. 5101-5128, 44701; Pub. L. 101-410 
Sec. 4 (28 U.S.C. 2461 note); Pub. L. 104-121 Sec. Sec. 212-213; Pub. 
L. 104-134 Sec. 31001; 49 CFR 1.45, 1.53.

    Source: 76 FR 11592, Mar. 2, 2011, unless otherwise noted.



                          Subpart A_Definitions



Sec. 109.1  Definitions.

    For purposes of this part, all terms defined in 49 U.S.C. 5102 are 
used in their statutory meaning. Other terms used in this part are 
defined as follows:
    Administrator means the head of any operating administration within 
the Department of Transportation, and includes the Administrators of the 
Federal Aviation Administration, Federal

[[Page 67]]

Motor Carrier Safety Administration, Federal Railroad Administration, 
and Pipeline and Hazardous Materials Safety Administration, to whom the 
Secretary has delegated authority in part 1 of this title, and any 
person within an operating administration to whom an Administrator has 
delegated authority to carry out this part.
    Agent of the Secretary or agent means a Federal officer, employee, 
or agent authorized by the Secretary to conduct inspections or 
investigations under the Federal hazardous material transportation law.
    Chief Safety Officer or CSO means the Assistant Administrator of the 
Pipeline and Hazardous Materials Safety Administration.
    Emergency order means an emergency restriction, prohibition, recall, 
or out-of-service order set forth in writing.
    Freight container means a package configured as a reusable container 
that has a volume of 64 cubic feet or more, designed and constructed to 
permit being lifted with its contents intact and intended primarily for 
containment of smaller packages (in unit form) during transportation.
    Immediately adjacent means a packaging that is in direct contact 
with the hazardous material or is otherwise the primary means of 
containment of the hazardous material.
    Imminent hazard means the existence of a condition relating to 
hazardous material that presents a substantial likelihood that death, 
serious illness, severe personal injury, or a substantial endangerment 
to health, property, or the environment may occur before the reasonably 
foreseeable completion date of a formal proceeding begun to lessen the 
risk of that death, illness, injury, or endangerment.
    In writing means unless otherwise specified, the written expression 
of any actions related to this part, rendered in paper or digital 
format, and delivered in person; via facsimile, commercial delivery, 
U.S. Mail; or electronically.
    Objectively reasonable and articulable belief means a belief based 
on particularized and identifiable facts that provide an objective basis 
to believe or suspect that a package may contain a hazardous material.
    Out-of-service order means a written requirement issued by the 
Secretary, or a designee, that an aircraft, vessel, motor vehicle, 
train, railcar, locomotive, other vehicle, transport unit, transport 
vehicle, freight container, portable tank, or other package not be moved 
or cease operations until specified conditions have been met.
    Packaging means a receptacle and any other components or materials 
necessary for the receptacle to perform its containment function in 
conformance with the minimum packing requirements of this subchapter. 
For radioactive materials packaging, see Sec. 173.403 of subchapter C 
of this chapter.
    Perishable hazardous material means a hazardous material that is 
subject to significant risk of speedy decay, deterioration, or spoilage, 
or hazardous materials consigned for medical use, in the prevention, 
treatment, or cure of a disease or condition in human beings or animals 
where expeditious shipment and delivery meets a critical medical need.
    Properly qualified personnel means a company, partnership, 
proprietorship, or individual who is technically qualified to perform 
designated tasks necessary to assist an agent in inspecting, examining, 
opening, removing, testing, or transporting packages.
    Related packages means any packages in a shipment, series or group 
of packages that can be traced to a common nexus of facts, including, 
but not limited to: The same offeror or packaging manufacturer; the same 
hazard communications information (marking, labeling, shipping 
documentation); or other reasonable and articulable facts that may lead 
an agent to believe such packages are related to a package that may pose 
an imminent hazard. Packages that are located within the same trailer, 
freight container, unit load device, etc. as a package removed subject 
to this enhanced authority without additional facts to substantiate its 
nexus to an imminent hazard are not ``related packages'' for purposes of 
removal. The related packages must also demonstrate that they may pose 
an imminent hazard. They must exhibit a commonality or nexus of origin, 
which may include, but are not limited to, a common offeror, package 
manufacturer,

[[Page 68]]

marking, labeling, shipping documentation, hazard communications, etc.
    Remove means to keep a package from entering the stream of 
transportation in commerce; to take a package out of the stream of 
transportation in commerce by physically detaining a package that was 
offered for transportation in commerce; or stopping a package from 
continuing in transportation in commerce.
    Safe and expeditious means prudent measures or procedures designed 
to minimize delay.



                Subpart B_Inspections and Investigations



Sec. 109.3  Inspections and Investigations.

    (a) General authority. An Administrator may initiate an inspection 
or investigation to determine compliance with Federal hazardous material 
transportation law, or a regulation, order, special permit, or approval 
prescribed or issued under the Federal hazardous material transportation 
law, or any court decree or order relating thereto.
    (b) Inspections and investigations. Inspections and investigations 
are conducted by designated agents of the Secretary who will, upon 
request, present their credentials for examination. Such an agent is 
authorized to:
    (1) Administer oaths and receive affirmations in any matter under 
investigation.
    (2) Gather information by any reasonable means, including, but not 
limited to, gaining access to records and property (including packages), 
interviewing, photocopying, photographing, and video- and audio-
recording in a reasonable manner.
    (3) Serve subpoenas for the production of documents or other 
tangible evidence if, on the basis of information available to the 
agent, the evidence is relevant to a determination of compliance with 
the Federal hazardous material transportation law, regulation, order, 
special permit, or approval prescribed or issued under the Federal 
hazardous material transportation law, or any court decree or order 
relating thereto. Service of a subpoena shall be in accordance with the 
requirements of the agent's operating administration as set forth in 14 
CFR 13.3 (Federal Aviation Administration); 49 CFR 209.7 (Federal 
Railroad Administration), 49 U.S.C. 502(d), 5121(a) (Federal Motor 
Carrier Safety Administration), and 49 CFR 105.45-105.55 (Pipeline and 
Hazardous Materials Safety Administration).



Sec. 109.5  Opening of packages.

    (a) When an agent has an objectively reasonable and articulable 
belief that a package offered for or in transportation in commerce may 
contain a hazardous material and that such a package does not otherwise 
comply with this chapter, the agent may--
    (1) Stop movement of the package in transportation and gather 
information from any person to learn the nature and contents of the 
package;
    (2) Open any overpack, outer packaging, or other component of the 
package that is not immediately adjacent to the hazardous materials 
contained in the package and examine the inner packaging(s) or packaging 
components.



Sec. 109.7  Removal from transportation.

    An agent may remove a package and related packages in a shipment or 
a freight container from transportation in commerce for up to forty-
eight (48) hours when the agent has an objectively reasonable and 
articulable belief that the packages may pose an imminent hazard. The 
agent must record this belief in writing as soon as practicable and 
provide written notification stating the reason for removal to the 
person in possession.



Sec. 109.9  Transportation for examination and analysis.

    (a) An agent may direct a package to be transported to a facility 
for examination and analysis when the agent determines that:
    (1) Further examination of the package is necessary to evaluate 
whether the package conforms to subchapter C of this chapter;
    (2) Conflicting information concerning the package exists; or
    (3) Additional investigation is not possible on the immediate 
premises.
    (b) In the event of a determination in accordance with paragraph (a) 
of this section, an agent may:

[[Page 69]]

    (1) Direct the offeror of the package, or other person responsible 
for the package, to have the package transported to a facility where the 
material may be examined and analyzed;
    (2) Direct the packaging manufacturer or tester of the packaging to 
have the package transported to a facility where the packaging may be 
tested in accordance with the HMR; or
    (3) Direct the carrier to transport the package to a facility 
capable of conducting such examination and analysis.
    (c) The 48-hour removal period provided in Sec. 109.7 may be 
extended in writing by the Administrator pending the conclusion of 
examination and analysis under this section.



Sec. 109.11  Assistance of properly qualified personnel.

    An agent may authorize properly qualified personnel to assist in the 
activities conducted under this part if the agent is not properly 
qualified to perform a function that is essential to the agent's 
exercise of authority under this part or when safety might otherwise be 
compromised by the agent's performance of such a function.



Sec. 109.13  Closing packages and safe resumption of transportation.

    (a) No imminent hazard found. If, after an agent exercises an 
authority under Sec. 109.5, the agent finds that no imminent hazard 
exists, and the package otherwise conforms to applicable requirements in 
subchapter C of this chapter, the agent will:
    (1) Assist in preparing the package for safe and prompt 
transportation, when practicable, by reclosing the package in accordance 
with the packaging manufacturer's closure instructions or other 
appropriate closure method;
    (2) Mark and certify the reclosed package to indicate that it was 
opened and reclosed in accordance with this part;
    (3) Return the package to the person from whom the agent obtained 
it, as soon as practicable; and
    (4) For a package containing a perishable hazardous material, assist 
in resuming the safe and expeditious transportation of the package as 
soon as practicable after determining that the package presents no 
imminent hazard.
    (b) Imminent hazard found. If an imminent hazard is found to exist 
after an agent exercises an authority under Sec. 109.5, the 
Administrator or his/her designee may issue an out-of-service order 
prohibiting the movement of the package until the package has been 
brought into compliance with subchapter C of this chapter. Upon receipt 
of the out-of-service order, the person in possession of, or responsible 
for, the package must remove the package from transportation until it is 
brought into compliance.
    (c) Package does not contain hazardous material. If, after an agent 
exercises an authority under Sec. 109.5, the agent finds that a package 
does not contain a hazardous material, the agent shall securely close 
the package, mark and certify the reclosed package to indicate that it 
was opened and reclosed, and return the package to transportation.
    (d) Non-compliant package. If, after an agent exercises an authority 
under Sec. 109.5, the agent finds that a package contains hazardous 
material and does not conform to requirements in subchapter C of this 
chapter, but does not present an imminent hazard, the agent will return 
the package to the person in possession of the package at the time the 
non-compliance is discovered for appropriate corrective action. A non-
compliant package may not continue in transportation until all 
identified non-compliance issues are resolved.



Sec. 109.15  Termination.

    When the facts disclosed by an investigation indicate that further 
action is not warranted under this Part at the time, the Administrator 
will close the investigation without prejudice to further investigation 
and notify the person being investigated of the decision. Nothing herein 
precludes civil enforcement action at a later time related to the 
findings of the investigation.



                       Subpart C_Emergency Orders



Sec. 109.17  Emergency Orders.

    (a) Determination of imminent hazard. When an Administrator 
determines

[[Page 70]]

that a violation of a provision of the Federal hazardous material 
transportation law, or a regulation or order prescribed under that law, 
or an unsafe condition or practice, constitutes or is causing an 
imminent hazard, as defined in Sec. 109.1, the Administrator may issue 
or impose emergency restrictions, prohibitions, recalls, or out-of-
service orders, without advance notice or an opportunity for a hearing. 
The basis for any action taken under this section shall be set forth in 
writing which must--
    (1) Describe the violation, condition, or practice that constitutes 
or is causing the imminent hazard;
    (2) Set forth the terms and conditions of the emergency order;
    (3) Be limited to the extent necessary to abate the imminent hazard; 
and,
    (4) Advise the recipient that, within 20 calendar days of the date 
the order is issued, recipient may request review; and that any request 
for a formal hearing in accordance with 5 U.S.C. 554 must set forth the 
material facts in dispute giving rise to the request for a hearing; and
    (5) Set forth the filing and service requirements contained in Sec. 
109.19(f), including the address of DOT Docket Operations and of all 
persons to be served with the petition for review.
    (b) Out-of-service order. An out-of-service order is issued to 
prohibit the movement of an aircraft, vessel, motor vehicle, train, 
railcar, locomotive, transport unit, transport vehicle, or other 
vehicle, or a freight container, portable tank, or other package until 
specified conditions of the out-of-service order have been met.
    (1) Upon receipt of an out-of-service order, the person in 
possession of, or responsible for, the package must remove the package 
from transportation until it is brought into compliance with the out-of-
service order.
    (2) A package subject to an out-of-service order may be moved from 
the place where it was found to present an imminent hazard to the 
nearest location where the package can be brought into compliance, 
provided that the agent who issued the out-of-service order is notified 
before the move.
    (3) The recipient of the out-of-service order must notify the 
operating administration that issued the order when the package is 
brought into compliance.
    (4) Upon receipt of an out-of-service order, a recipient may appeal 
the decision of the agent issuing the order to PHMSA's Chief Safety 
Officer. A petition for review of an out-of-service order must meet the 
requirements of Sec. 109.19.
    (c) Recalls. PHMSA's Associate Administrator, Office of Hazardous 
Materials Safety, may issue an emergency order mandating the immediate 
recall of any packaging, packaging component, or container certified, 
represented, marked, or sold as qualified for use in the transportation 
of hazardous materials in commerce when the continued use of such item 
would constitute an imminent hazard. All petitions for review of such an 
emergency order will be governed by the procedures set forth at Sec. 
109.19.



Sec. 109.19  Petitions for review of emergency orders.

    (a) Petitions for review. A petition for review must--
    (1) Be in writing;
    (2) State with particularity each part of the emergency order that 
is sought to be amended or rescinded and include all information, 
evidence and arguments in support thereof;
    (3) State whether a formal hearing in accordance with 5 U.S.C. 554 
is requested, and, if so, the material facts in dispute giving rise to 
the request for a hearing; and,
    (4) Be filed and served in accordance with Sec. 109.19(f).
    (b) Response to the petition for review. An attorney designated by 
the Office of Chief Counsel of the operating administration issuing the 
emergency order may file and serve, in accordance with Sec. 109.19(f), 
a response, including appropriate pleadings, within five calendar days 
of receipt of the petition by the Chief Counsel of the operating 
administration issuing the emergency order.
    (c) Chief Safety Officer Responsibilities.
    (1) Hearing requested. Upon receipt of a petition for review of an 
emergency order that includes a formal hearing request and states 
material facts in dispute, the Chief Safety Officer shall immediately 
assign the petition to the

[[Page 71]]

Office of Hearings. Unless the Chief Safety Officer issues an order 
stating that the petition fails to set forth material facts in dispute 
and will be decided under paragraph (c)(2) of this section, a petition 
for review including a formal hearing request will be deemed assigned to 
the Office of Hearings three calendar days after the Chief Safety 
Officer receives it.
    (2) No hearing requested. For a petition for review of an emergency 
order that does not include a formal hearing request or fails to state 
material facts in dispute, the Chief Safety Officer shall issue an 
administrative decision on the merits within 30 days of receipt of the 
petition. The Chief Safety Officer's decision constitutes final agency 
action.
    (d) Hearings. Formal hearings shall be conducted by an 
Administrative Law Judge assigned by the Chief Administrative Law Judge 
of the Office of Hearings. The Administrative Law Judge may:
    (1) Administer oaths and affirmations;
    (2) Issue subpoenas as provided by the appropriate agency 
regulations (49 CFR 209.7, 49 CFR 105.45, 14 CFR 13.3, and 49 U.S.C. 502 
and 31133);
    (3) Adopt the relevant Federal Rules of Civil Procedure for the 
United States District Courts for the procedures governing the hearings 
when appropriate;
    (4) Adopt the relevant Federal Rules of Evidence for United States 
Courts and Magistrates for the submission of evidence when appropriate;
    (5) Take or cause depositions to be taken;
    (6) Examine witnesses at the hearing;
    (7) Rule on offers of proof and receive relevant evidence;
    (8) Convene, recess, adjourn or otherwise regulate the course of the 
hearing;
    (9) Hold conferences for settlement, simplification of the issues, 
or any other proper purpose; and,
    (10) Take any other action authorized by or consistent with the 
provisions of this part and permitted by law that may expedite the 
hearing or aid in the disposition of an issue raised therein.
    (e) Parties. The petitioner may appear and be heard in person or by 
an authorized representative. The operating administration issuing the 
emergency order shall be represented by an attorney designated by its 
respective Office of Chief Counsel.
    (f) Filing and service. (1) Each petition, pleading, motion, notice, 
order, or other document submitted in connection with an order issued 
under this subpart must be filed (commercially delivered or submitted 
electronically) with: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590. All documents filed will be 
published on the Department's docket management Web site, http://
www.regulations.gov. The emergency order shall state the above filing 
requirements and the address of DOT Docket Operations.
    (2) Service. Each document filed in accordance with paragraph (f)(1) 
of this section must be concurrently served upon the following persons:
    (i) Chief Safety Officer (Attn: Office of Chief Counsel, PHC), 
Pipeline and Hazardous Materials Safety Administration, U.S. Department 
of Transportation, 1200 New Jersey Avenue, SE., East Building, 
Washington, DC 20590 (facsimile: 202-366-7041) (electronic mail: 
PHMSAChiefCounsel@dot.gov);
    (ii) The Chief Counsel of the operating administration issuing the 
emergency order;
    (iii) If the petition for review requests a formal hearing, the 
Chief Administrative Law Judge, U.S. Department of Transportation, 
Office of Hearings, M-20, Room E12-320, 1200 New Jersey Avenue, SE., 
Washington, DC 20590 (facsimile: 202-366-7536).
    (iv) Service shall be made personally, by commercial delivery 
service, or by electronic means if consented to in writing by the party 
to be served, except as otherwise provided herein. The emergency order 
shall state all relevant service requirements and list the persons to be 
served and may be updated as necessary. The emergency order shall also 
be published in the Federal Register as soon as practicable after its 
issuance.

[[Page 72]]

    (3) Certificate of service. Each order, pleading, motion, notice, or 
other document shall be accompanied by a certificate of service 
specifying the manner in which and the date on which service was made.
    (4) The emergency order shall be served by ``hand delivery,'' unless 
such delivery is not practicable, or by electronic means if consented to 
in writing by the party to be served.
    (5) Service upon a person's duly authorized representative, agent 
for service, or an organization's president constitutes service upon 
that person.
    (g) Report and recommendation. The Administrative Law Judge shall 
issue a report and recommendation at the close of the record. The report 
and recommendation shall:
    (1) Contain findings of fact and conclusions of law and the grounds 
for the decision based on the material issues of fact or law presented 
on the record;
    (2) Be served on the parties to the proceeding; and
    (3) Be issued no later than 25 days after receipt of the petition 
for review by the Chief Safety Officer.
    (h) Expiration of order. If the Chief Safety Officer, or the 
Administrative Law Judge, where appropriate, has not disposed of the 
petition for review within 30 days of receipt, the emergency order shall 
cease to be effective unless the Administrator issuing the emergency 
order determines, in writing, that the imminent hazard providing a basis 
for the emergency order continues to exist. The requirements of such an 
extension shall remain in full force and effect pending decision on a 
petition for review unless stayed or modified by the Administrator.
    (i) Reconsideration.
    (1) A party aggrieved by the Administrative Law Judge's report and 
recommendation may file a petition for reconsideration with the Chief 
Safety Officer within one calendar day of service of the report and 
recommendation. The opposing party may file a response to the petition 
within one calendar day of service of a petition for reconsideration.
    (2) The Chief Safety Officer shall issue a final agency decision 
within three calendar days of service of the final pleading, but no 
later than 30 days after receipt of the original petition for review.
    (3) The Chief Safety Officer's decision on the merits of a petition 
for reconsideration constitutes final agency action.
    (j) Appellate review. A person aggrieved by the final agency action 
may petition for review of the final decision in the appropriate Court 
of Appeals for the United States as provided in 49 U.S.C. 5127. The 
filing of the petition for review does not stay or modify the force and 
effect of the final agency.
    (k) Time. In computing any period of time prescribed by this part or 
by an order issued by the Administrative Law Judge, the day of filing of 
the petition for review or of any other act, event, or default from 
which the designated period of time begins to run shall not be included. 
The last day of the period so computed shall be included, unless it is a 
Saturday, Sunday, or Federal holiday, in which event the period runs 
until the end of the next day which is not one of the aforementioned 
days.



Sec. 109.21  Remedies generally.

    An Administrator may request the Attorney General to bring an action 
in the appropriate United States district court seeking temporary or 
permanent injunctive relief, punitive damages, assessment of civil 
penalties as provided by 49 U.S.C. 5122(a), and any other appropriate 
relief to enforce the Federal hazardous material transportation law, 
regulation, order, special permit, or approval prescribed or issued 
under the Federal hazardous material transportation law.



PART 110_HAZARDOUS MATERIALS PUBLIC SECTOR TRAINING AND PLANNING GRANTS--Table 

of Contents



Sec.
110.1 Purpose.
110.5 Scope.
110.7 Control Number under the Paperwork Reduction Act.
110.10 Eligibility.
110.20 Definitions.
110.30 Grant application.
110.40 Activities eligible for funding.
110.50 Disbursement of Federal funds.
110.60 Cost sharing for planning and training.
110.70 Financial administration.

[[Page 73]]

110.80 Procurement.
110.90 Grant monitoring, reports, and records retention.
110.100 Enforcement.
110.110 After-grant requirements.
110.120 Deviation from this part.
110.130 Disputes.

    Authority: 49 U.S.C. 5101-5127; 49 CFR 1.53.

    Source: Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, unless otherwise 
noted.

    Editorial Note: Nomenclature changes to part 110 appear at 70 FR 
56090, Sept. 23, 2005.



Sec. 110.1  Purpose.

    This part sets forth procedures for reimbursable grants for public 
sector planning and training in support of the emergency planning and 
training efforts of States, Indian tribes, and local communities to deal 
with hazardous materials emergencies, particularly those involving 
transportation. These grants will enhance the implementation of the 
Emergency Planning and Community Right-to-Know Act of 1986 (42 U.S.C. 
11001).



Sec. 110.5  Scope.

    (a) This part applies to States and Indian tribes and contains the 
program requirements for public sector training and planning grants to 
support hazardous materials emergency planning and training efforts.
    (b) The requirements contained in 49 CFR part 18, ``Uniform 
Administrative Requirements for Grants and Cooperative Agreements to 
State and Local Governments'', apply to grants issued under this part.
    (c) Copies of standard forms and OMB circulars referenced in this 
part are available from the HMTUSA Grants Manager, Pipeline and 
Hazardous Materials Safety Administration, U.S. Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington 
DC 20590-0001.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended at 72 FR 55683, 
Oct. 1, 2007]



Sec. 110.7  Control Number under the Paperwork Reduction Act.

    The Office of Management and Budget control number assigned to 
collection of information in Sec. Sec. 110.30, 110.70, 110.80, and 
110.90 is 2137-0586.



Sec. 110.10  Eligibility.

    This part applies to States and Indian tribes. States may apply for 
planning and training grants. Federally-recognized Indian tribes may 
apply for training grants.



Sec. 110.20  Definitions.

    Unless defined in this part, all terms defined in 49 U.S.C. 5102 are 
used in their statutory meaning and all terms defined in 49 CFR part 18 
and OMB Circular A-102, with respect to administrative requirements for 
grants, are used as defined therein. Other terms used in this part are 
defined as follows:
    Allowable costs means those costs that are: eligible, reasonable, 
necessary, and allocable to the project permitted by the appropriate 
Federal cost principles, and approved in the grant.
    Associate Administrator means the Associate Administrator for 
Hazardous Materials Safety, Pipeline and Hazardous Materials Safety 
Administration.
    Budget period means the period of time specified in the grant 
agreement during which the project manager may expend or obligate 
project funds.
    Cost review means the review and evaluation of costs to determine 
reasonableness, allocability, and allowability.
    Indian country means Indian country as defined in 18 U.S.C. 1151. 
That section defines Indian country as all land within the limits of any 
reservation under the jurisdiction of the U.S. Government, 
notwithstanding the issuance of any patent, and, including rights-of-way 
running through the reservation; all dependent Indian communities within 
the borders of the United States whether within the original or 
subsequently acquired territory thereof, and whether within or without 
the limits of a State; and all Indian allotments, the Indian titles to 
which have not been extinguished, including rights-of-way running 
through the same.
    Indian tribe means a tribe ``Federally-recognized'' by the Secretary 
of the Interior under 25 CFR 272.2.
    Local Emergency Planning Committee (LEPC) means a committee 
appointed by the State Emergency Response Commission under section 
301(c) of the Emergency Planning and Community

[[Page 74]]

Right-to-Know Act of 1986 (42 U.S.C. 11001(c)) that includes at a 
minimum, representatives from each of the following groups or 
organizations: elected State and local officials; law enforcement, 
firefighting, civil defense, first aid, health, local environmental, 
hospital, and transportation personnel; broadcast and print media; 
community groups; and owners and operators of facilities subject to the 
emergency planning requirements.
    National curriculum means the curriculum required to be developed 
under 49 U.S.C. 5115 and necessary to train public sector emergency 
response and preparedness teams, enabling them to comply with 
performance standards as stated in 49 U.S.C. 5115(c).
    Political subdivision means a county, municipality, city, town, 
township, local public authority (including any public and Indian 
housing agency under the United States Housing Act of 1937 (42 U.S.C. 
1401 et seq.), school district, special district, intrastate district, 
council of governments (whether or not incorporated as a nonprofit 
corporation under State law), any other regional or interstate 
government entity, or any agency or instrumentality of a local 
government.
    Project means the activities and tasks identified in the grant 
agreement.
    Project manager means the State or Indian tribal official designated 
in a grant as the recipient agency's principal program contact with the 
Federal Government.
    Project officer means the Federal official designated in a grant as 
the program contact with the project manager. The project officer is 
responsible for monitoring the project.
    Project period means the length of time specified in a grant for 
completion of all work associated with that project.
    State Emergency Response Commission (SERC) means the State Emergency 
Response Commission appointed by the Governor of each State and 
Territory under the Emergency Planning and Community Right-to-Know Act 
of 1986.
    Statement of Work means that portion of a grant that describes the 
purpose and scope of activities and tasks to be carried out as part of 
the proposed project.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59 
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001]



Sec. 110.30  Grant application.

    (a) General. An applicant for a planning or training grant shall use 
only the standard application forms approved by the Office of Management 
and Budget (OMB) (SF-424 and SF-424A) under the Paperwork Reduction Act 
of 1980 (44 U.S.C. 3502). Applicants are required to submit an original 
and two copies of the application package to: Grants Manager, Pipeline 
and Hazardous Materials Safety Administration, U.S. Department of 
Transportation, East Building, 1200 New Jersey Avenue, SE., Washington, 
DC 20590-0001. Applications received on or before January 1st and July 
1st of each year will be considered in that cycle of the semi-annual 
review and award process. An initial round of the review and award 
process will consider applications received on or before November 15, 
1992. Requests and continuation applications must include an original 
and two copies of the affected pages; previously submitted pages with 
information that is still current do not have to be resubmitted. The 
application must include the following:
    (1) Application for Federal Assistance for non-construction programs 
(SF-424) and Budget sheets (SF-424A). A single application may be used 
for both planning and training if the budgets for each are entered 
separately on all budget sheets.
    (2) For States, a letter from the Governor designating the State 
agency that is authorized to apply for a grant and to provide the 
written certifications required to receive a grant.
    (3) For Indian tribes, a letter from the tribal government, 
governing body, or tribal council to the effect that the applicant is 
authorized to apply for a grant and to provide the written 
certifications required to receive a grant.
    (4) A written statement explaining whether the State or tribe 
assesses and collects fees on the transportation of hazardous materials 
and whether such assessments or fees are used solely to

[[Page 75]]

carry out purposes related to the transportation of hazardous materials.
    (5) A statement designating a project manager and providing the 
name, position, address and phone number of that individual who will be 
responsible for coordinating the funded activities with other agencies/
organizations.
    (6) A project narrative statement of the goals and objectives of the 
proposed project, project design, and long range plans. The proposed 
grant project and budget periods may be one or more years.
    (7) A statement of work in support of the proposed project that 
describes and sets priorities for the activities and tasks to be 
conducted, the costs associated with each activity, the number and types 
of deliverables and products to be completed, and a schedule for 
implementation.
    (8) A description of the major items of costs needed to implement 
the statement of work and a copy of any cost or price analysis if 
conducted.
    (9) Drug-Free Workplace Certification. The applicant must certify as 
specified in appendix C of 49 CFR part 29 that it will comply with the 
Drug-Free Workplace Act of 1988 (Pub. L. 100-690, title V, subtitle D; 
51 U.S.C. 701 et seq.).
    (10) Anti-Lobbying Certification. The applicant must certify as 
specified in appendix A of 49 CFR part 20 that no Federal funds will be 
expended to pay any person for influencing or attempting to influence an 
officer or employee of any agency, a Member of Congress, an officer or 
employee of Congress, or an employee of a Member of Congress (section 
319 of Pub. L. 101-121, 31 U.S.C. 1352).
    (11) Debarment and Suspension Certification. The applicant must 
certify as specified in subpart G of 49 CFR part 29 that it will not 
make an award or permit any award to any party which is debarred or 
suspended or is otherwise excluded from or ineligible for participation 
in Federal assistance programs.
    (b) Planning. In addition to the requirements specified in paragraph 
(a) of this section, eligible State applicants must include the 
following in their application package:
    (1) A written certification that the State is complying with 
sections 301 and 303 of the Emergency Planning and Community Right-to-
Know Act of 1986, including a brief explanation of how compliance has 
been achieved.
    (2) A written statement specifying the aggregate expenditure of 
funds of the State, exclusive of Federal funds, for each of its last 
five fiscal years for developing, improving, and implementing emergency 
plans under the Emergency Planning and Community Right-to-Know Act of 
1986, including an explanation specifying the sources of these funds. A 
written certification that the State's aggregate expenditures, as 
defined by the State, of funds for this purpose, exclusive of Federal 
funds, will not fall below the average level of its expenditures for its 
last five fiscal years. The applicant may not claim any of these 
expenditures for cost-sharing.
    (3) A written statement agreeing to make at least 75 percent of the 
Federal funds awarded available to LEPCs and an explanation of how the 
applicant intends to make such funds available to them for developing, 
improving, or implementing emergency plans.
    (4) Designation of a project manager to serve as contact for 
coordinating planning funds under this program.
    (5) A project narrative statement of the goals and objectives of 
each proposed project, including the following:
    (i) A background statement describing the applicant's long-term 
goals and objectives with respect to:
    (A) The current abilities and authorities of the applicant's program 
for preparedness planning;
    (B) The need to sustain or increase program capability;
    (C) Current degree of participation in or intention to assess the 
need for a regional hazardous materials emergency response team; and
    (D) The impact that the grant will have on the program.
    (ii) A discussion of whether the applicant's program currently 
knows, or intends to assess, transportation flow patterns of hazardous 
materials within the State and between that State and another State.
    (iii) A schedule for implementing the proposed grant activities.
    (iv) A statement describing the ways in which planning will be 
monitored by the project manager.

[[Page 76]]

    (v) A statement indicating that all members of the State Emergency 
Response Commission were provided the opportunity to review the grant 
application.
    (c) Training. In addition to the requirements specified in paragraph 
(a) of this section, eligible State and Indian tribe applicants must 
include the following in their application package:
    (1) For a State applicant, a written certification explaining how 
the State is complying with sections 301 and 303 of the Emergency 
Planning and Community Right-to-Know Act.
    (2) A written statement specifying the aggregate expenditure of 
funds of the State or Indian tribe, exclusive of Federal funds, for each 
of its last five fiscal years for training public sector employees to 
respond to accidents and incidents involving hazardous materials, 
including an explanation specifying the sources of these funds. A 
written certification that the applicant's aggregate expenditure, as 
defined by the State or tribe, of funds for this purpose, exclusive of 
Federal funds, will not fall below the average level of its expenditures 
for its last five fiscal years. The applicant may not claim any of these 
expenditures for cost-sharing purposes.
    (3) For a State applicant, a written statement agreeing to make at 
least 75 percent of the Federal funds awarded available for the purpose 
of training public sector employees employed or used by political 
subdivisions. A State applicant may elect to pass all or some portion of 
the grant on to political subdivisions for this purpose. The applicant 
must include a specific explanation of how it intends to meet this 
requirement.
    (4) Designation of a primary point of contact for coordinating 
training funded under this program. Identification of a single 
repository for copies of course materials delivered under the grant as 
specified in Sec. 110.90 of this part.
    (5) A project narrative statement of the long-range goals and 
objectives of each proposed project, including the following:
    (i) A background statement describing:
    (A) The current hazardous materials training program(s);
    (B) Training audience, including numbers and levels of training and 
accreditation program for each level or criterion required to advance to 
the next level;
    (C) Estimated total number of persons to be trained under the 
proposed project;
    (D) The ways in which training grants will support the integrated 
delivery of training to meet the needs of individualized geographic and 
resource needs and time considerations of local responders. When 
appropriate, a statement describing how the proposed project will 
accommodate the different training needs for rural versus urban 
environments; and
    (E) The impact that the grant and the National Curriculum will have 
on the program.
    (ii) A statement describing how the National Curriculum will be used 
or modified to train public sector employees at the local level to 
respond to accidents and incidents involving hazardous materials.
    (iii) A statement describing the ways in which effectiveness of 
training will be monitored by the project manager, including, but not 
limited to, examinations, critiques, and instructor evaluations.
    (iv) A schedule for implementing the proposed training grant 
activities.
    (v) A statement indicating that all members of the State or Tribal 
Emergency Response Commission were provided the opportunity to review 
the grant application.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59 
FR 49132, Sept. 26, 1994; 70 FR 73162, Dec. 9, 2005; 72 FR 55683, Oct. 
1, 2007]



Sec. 110.40  Activities eligible for funding.

    (a) Planning. Eligible State applicants may receive funding for the 
following activities:
    (1) Development, improvement, and implementation of emergency plans 
required under the Emergency Planning and Community Right-to-Know Act of 
1986, as well as exercises which test the emergency plan. Enhancement of 
emergency plans to include hazard analysis as well as response 
procedures for

[[Page 77]]

emergencies involving transportation of hazardous materials, including 
radioactive materials.
    (2) An assessment to determine flow patterns of hazardous materials 
within a State, between a State and another State or Indian country, and 
development and maintenance of a system to keep such information 
current.
    (3) An assessment of the need for regional hazardous materials 
emergency response teams.
    (4) An assessment of local response capabilities.
    (5) Conduct of emergency response drills and exercises associated 
with emergency preparedness plans.
    (6) Provision of technical staff to support the planning effort.
    (7) Additional activities the Associate Administrator deems 
appropriate to implement the scope of work for the proposed project plan 
and approved in the grant.
    (b) Training. Eligible State and Indian tribe applicants may receive 
funding for the following activities:
    (1) An assessment to determine the number of public sector employees 
employed or used by a political subdivision who need the proposed 
training and to select courses consistent with the National Curriculum.
    (2) Delivery of comprehensive preparedness and response training to 
public sector employees. Design and delivery of preparedness and 
response training to meet specialized needs. Financial assistance for 
trainees and for the trainers, if appropriate, such as tuition, travel 
expenses to and from a training facility, and room and board while at 
the training facility.
    (3) Emergency response drills and exercises associated with 
training, a course of study, and tests and evaluation of emergency 
preparedness plans.
    (4) Expenses associated with training by a person (including a 
department, agency, or instrumentality of a State or political 
subdivision thereof or an Indian tribe) and activities necessary to 
monitor such training including, but not limited to examinations, 
critiques and instructor evaluations.
    (5) Provision of staff to manage the training effort designed to 
result in increased benefits, proficiency, and rapid deployment of local 
and regional responders.
    (6) Additional activities the Associate Administrator deems 
appropriate to implement the scope of work for the proposed project and 
approved in the grant.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377, 
Aug. 28, 2001]



Sec. 110.50  Disbursement of Federal funds.

    (a) Preaward expenditures may not be reimbursed.
    (b) Reimbursement may not be made for a project plan unless approved 
in the grant award.
    (c) If a recipient agency seeks additional funds, the amendment 
request will be evaluated on the basis of needs, performance and 
availability of funds. An existing grant is not a commitment of future 
Federal funding.



Sec. 110.60  Cost sharing for planning and training.

    (a) The recipient agency must provide 20 percent of the direct and 
indirect costs of all activities covered under the grant award program 
with non-Federal funds. Recipients may either use cash (hard-match), in-
kind (soft-match) contributions, or a combination of in-kind plus hard-
match to meet this requirement. In-kind (soft-match) contributions are 
in addition to the maintenance of effort required of recipients of grant 
awards. The types of contributions allowed are as follows:
    (1) Any funds from a State, local, or other non-Federal source used 
for an eligible activity as defined in Sec. 110.40 in this part.
    (2) The dollar equivalent value of an eligible activity as defined 
in Sec. 110.40 of this part provided by a State, local, or other non-
Federal source.
    (3) The value of participants' salary while attending a planning or 
training activity contained in the approved grant application provided 
by a State, local, or other non-Federal source.
    (4) Additional types of in-kind contributions the Associate 
Administrator deems appropriate.
    (b) Funds used for matching purposes under any other Federal grant 
or cooperative agreement may not be used for matching purposes. The 
funds expended

[[Page 78]]

by a recipient agency to qualify for the grant may not be used for cost-
sharing purposes.
    (c) Acceptable contributions for matching and cost sharing purposes 
must conform to 49 CFR part 18.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59 
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001]



Sec. 110.70  Financial administration.

    (a) A State must expend and account for grant funds in accordance 
with State laws and procedures for expending and accounting for its own 
funds. Fiscal control and accounting procedures of the State, as well as 
its subgrantees and cost-type contractors, must be sufficient to:
    (1) Permit the preparation of reports required by 49 CFR part 18 and 
this part, including the tracing of funds provided for planning to a 
level of expenditure adequate to establish that at least 75 percent of 
the funds provided were made available to LEPCs for developing, 
improving, and implementing emergency plans; and the tracing of funds 
provided for training to a level of expenditure adequate to establish 
that at least 75 percent of the funds provided were made available for 
the purposes of training public sector employees employed or used by 
political subdivisions.
    (2) Permit the tracing of funds to a level of expenditure adequate 
to establish that such funds have not been used in violation of the 
restrictions and prohibitions of applicable statutes.
    (b) The financial management systems of Indian tribes and any 
subgrantees must meet the standards of 49 CFR 18.20, including the 
ability to trace funds provided for training to a level of expenditure 
adequate to establish that at least 75 percent of the funds provided 
were made available for the purposes of training public sector employees 
employed or used by political subdivisions.
    (c) Advances shall be made to States and Indian tribes consistent 
with 49 CFR part 18 and 31 CFR part 205. The Associate Administrator 
shall base these advances on demonstrated need, which will be determined 
on a case-by-case basis, considering such factors as State/Tribal budget 
constraints and reductions in amounts budgeted for hazardous materials 
activities. To obtain an advance, a State or Indian tribe must comply 
with the following requirements:
    (1) A letter from the Governor or Tribal leader or their designee is 
required specifying the extenuating circumstances requiring the funding 
advance for the grant;
    (2) The maximum advance request may not be more than $25,000 for 
each State or Indian tribe;
    (3) Recipients of advance funding must obligate those funds within 3 
months of receipt;
    (4) Advances including interest will be deducted from the initial 
reimbursement to the State or Indian tribe; and
    (5) The State or Indian tribe will have its allocation of current 
grant funds reduced and will not be permitted to apply for future grant 
funds until the advance is covered by a request for reimbursement. For 
example, if $25,000 is advanced for personnel costs, this advance would 
be deducted from the initial reimbursement in the year the advance was 
made.
    (d) To be allowable, costs must be eligible, reasonable, necessary, 
and allocable to the approved project in accordance with OMB Circular A-
87 and included in the grant award. Costs incurred prior to the award of 
any grant are not allowable. Recipient agencies are responsible for 
obtaining audits in accordance with the Single Audit Act of 1984 (31 
U.S.C. 7501), 49 CFR part 90, and OMB Circular A-128. Audits shall be 
made by an independent auditor in accordance with generally accepted 
government auditing standards covering financial and compliance audits. 
The Associate Administrator may audit a recipient agency at any time.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377, 
Aug. 28, 2001]



Sec. 110.80  Procurement.

    Project managers shall use procurement procedures and practices 
which reflect applicable State laws and regulations and Federal 
requirements as specified in 49 CFR 18.36.

[[Page 79]]



Sec. 110.90  Grant monitoring, reports, and records retention.

    (a) Grant monitoring. Project managers are responsible for managing 
the day-to-day operations of grant, subgrant and contract-supported 
activities. Project managers must monitor performance of supported 
activities to assure compliance with applicable Federal requirements and 
achievement of performance goals. Monitoring must cover each program, 
function, activity, or task covered by the grant. Monitoring and 
reporting requirements for planning and training are contained in this 
part; general grant reporting requirements are specified in 49 CFR 
18.40.
    (b) Reports. (1) The project manager shall submit a performance 
report at the completion of an activity for which reimbursement is being 
requested or with a request to amend the grant. The final performance 
report is due 90 days after the expiration or termination of the grant.
    (2) Project managers shall submit an original and two copies of all 
performance reports. Performance reports for planning and training must 
include comparison of actual accomplishments to the stated goals and 
objectives established for the performance period, and the reasons for 
not achieving those goals and objectives, if applicable.
    (3) Project managers shall report developments or events that occur 
between the required performance reporting dates which have significant 
impact upon the planning and training activity such as:
    (i) Problems, delays, or adverse conditions which will impair the 
ability to meet the objective of the grant; and
    (ii) Favorable developments which enable meeting time schedules and 
objectives sooner or at less cost than anticipated or producing more 
beneficial results than originally planned.
    (4) Financial reporting, except as provided in Sec. 110.70 and 49 
CFR 18.41, shall be supplied quarterly using Standard Form 270, Request 
for Advance or Reimbursement, to report the status of funds. The project 
manager shall report separately on planning and training.
    (c) Records retention. In accordance with 49 CFR 18.42, all 
financial and programmatic records, supporting documents, statistical 
records, training materials, and other documents generated under a grant 
shall be maintained by the project manager for three years from the date 
the project manager submits the final financial status report (SF 269) 
or Request for Advance or Reimbursement (SF 270). The project manager 
shall designate a repository and single-point of contact for planning 
and for training, or both, for these purposes. If any litigation, claim, 
negotiation, audit or other action involving the records has been 
started before the expiration of the 3-year period, the records must be 
retained until completion of the action and resolution of all issues 
which arise from it, or until the end of the regular 3-year period, 
whichever is later.



Sec. 110.100  Enforcement.

    If a recipient agency fails to comply with any term of an award 
(whether stated in a Federal statute or regulation, an assurance, a 
State plan or application, a notice of award, or elsewhere) a 
noncompliance action may be taken as specified in 40 CFR 18.43. The 
recipient agency may appeal any such actions as specified in 49 CFR part 
18. Costs incurred by the recipient agency during a suspension or after 
termination of an award are not allowable unless the Associate 
Administrator authorizes it in writing. Grant awards may be terminated 
in whole or in part with the consent of the recipient at any agreed upon 
effective date, or by the recipient upon written notification.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377, 
Aug. 28, 2001]



Sec. 110.110  After-grant requirements.

    The Associate Administrator will close out the award upon 
determination that all applicable administrative actions and all 
required work of the grant are complete in accordance with subpart D of 
49 CFR part 18. The project manager must submit all financial, 
performance, and other reports required as a condition of the grant, 
within 90 days after the expiration or termination of the grant. This 
time

[[Page 80]]

frame may be extended by the Associate Administrator for Hazardous 
Materials Safety for cause.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by 66 FR 45377, 
Aug. 28, 2001]



Sec. 110.120  Deviation from this part.

    Recipient agencies may request a deviation from the non-statutory 
provisions of this part. The Associate Administrator will respond to 
such requests in writing. If appropriate, the decision will be included 
in the grant agreement. Request for deviations from part 110 must be 
submitted to: Grants Manager, Pipeline and Hazardous Materials Safety 
Administration, U.S. Department of Transportation, East Building, 1200 
New Jersey Avenue, SE., Washington, DC 20590-0001.

[Amdt. 110-1, 57 FR 43067, Sept. 17, 1992, as amended by Amdt. 110-3, 59 
FR 49132, Sept. 26, 1994; 66 FR 45377, Aug. 28, 2001; 72 FR 55683, Oct. 
1, 2007]



Sec. 110.130  Disputes.

    Disputes should be resolved at the lowest level possible, beginning 
with the project manager and the project officer. If an agreement cannot 
be reached, the Administrator, PHMSA, will serve as the dispute 
resolution official, whose decision will be final.

[[Page 81]]



                     SUBCHAPTER B_OIL TRANSPORTATION



PART 130_OIL SPILL PREVENTION AND RESPONSE PLANS--Table of Contents



Sec.
130.1 Purpose.
130.2 Scope.
130.3 General requirements.
130.5 Definitions.
130.11 Communication requirements.
130.21 Packaging requirements.
130.31 Response plans.
130.33 Response plan implementation.

    Authority: 33 U.S.C. 1321.

    Source: Amdt. 130-2, 61 FR 30541, June 17, 1996, unless otherwise 
noted.



Sec. 130.1  Purpose.

    This part prescribes prevention, containment and response planning 
requirements of the Department of Transportation applicable to 
transportation of oil by motor vehicles and rolling stock.



Sec. 130.2  Scope.

    (a) The requirements of this part apply to--
    (1) Any liquid petroleum oil in a packaging having a capacity of 
3,500 gallons or more; and
    (2) Any liquid petroleum or non-petroleum oil in a quantity greater 
than 42,000 gallons per packaging.
    (b) The requirements of this part have no effect on--
    (1) The applicability of the Hazardous Materials Regulations set 
forth in subchapter C of this chapter; and
    (2) The discharge notification requirements of the United States 
Coast Guard (33 CFR part 153) and EPA (40 CFR part 110).
    (c) The requirements of this part do not apply to--
    (1) Any mixture or solution in which oil is in a concentration by 
weight of less than 10 percent.
    (2) Transportation of oil by aircraft or vessel.
    (3) Any petroleum oil carried in a fuel tank for the purpose of 
supplying fuel for propulsion of the transport vehicle to which it is 
attached.
    (4) Oil transport exclusively within the confines of a non-
transportation-related or terminal facility in a vehicle not intended 
for use in interstate or intrastate commerce (see 40 CFR part 112, 
appendix A).
    (d) The requirements in Sec. 130.31(b) of this part do not apply to 
mobile marine transportation-related facilities (see 33 CFR part 154).



Sec. 130.3  General requirements.

    No person may offer or accept for transportation or transport oil 
subject to this part unless that person--
    (a) Complies with this part; and
    (b) Has been instructed on the applicable requirements of this part.



Sec. 130.5  Definitions.

    In this subchapter: Animal fat means a non-petroleum oil, fat, or 
grease derived from animals, not specifically identified elsewhere in 
this part.
    Contract or other means is:
    (1) A written contract with a response contractor identifying and 
ensuring the availability of the necessary personnel or equipment within 
the shortest practicable time;
    (2) A written certification by the owner or operator that the 
necessary personnel or equipment can and will be made available by the 
owner or operator within the shortest practicable time; or
    (3) Documentation of membership in an oil spill response 
organization that ensures the owner's or operator's access to the 
necessary personnel or equipment within the shortest practicable time.
    EPA means the U.S. Environmental Protection Agency.
    Liquid means a material that has a vertical flow of over two inches 
(50 mm) within a three-minute period, or a material having one gram or 
more liquid separation, when determined in accordance with the 
procedures specified in ASTM D 4359-84, ``Standard Test Method for 
Determining Whether a Material is a Liquid or a Solid,'' 1990 edition, 
which is incorporated by reference.

    Note: This incorporation by reference has been approved by the 
Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 
1 CFR part 51. A copy may be obtained

[[Page 82]]

from the American Society for Testing and Materials, 1916 Race Street, 
Philadelphia, PA 19103. Copies may be inspected at the Office of 
Hazardous Materials Safety, Office of Hazardous Materials Standards, 
Room 8422, DOT headquarters building, 400 7th St., SW, Washington, DC 
20590, or at the National Archives and Records Administration (NARA). 
For information on the availability of this material at NARA, call 202-
741-6030, or go to: http://www.archives.gov/federal--register/code--of--
federal--regulations/ibr--locations.html.

    Maximum extent practicable means the limits of available technology 
and the practical and technical limits on an owner or operator of an 
onshore facility in planning the response resources required to provide 
the on-water recovery capability and the shoreline protection and 
cleanup capability to conduct response activities for a worst-case 
discharge of oil in adverse weather.
    Non-petroleum oil means any animal fat, vegetable oil or other non-
petroleum oil.
    Oil means oil of any kind or in any form, including, but not limited 
to, petroleum, fuel oil, sludge, oil refuse, and oil mixed with wastes 
other than dredged spoil.

    Note: This definition does not include hazardous substances (see 40 
CFR part 116).

    Other non-petroleum oil means a non-petroleum oil of any kind that 
is not an animal fat or vegetable oil.
    Packaging means a receptacle and any other components or materials 
necessary for the receptacle to perform its containment function in 
conformance with the packaging requirements of this part. A 
compartmented tank is a single packaging.
    Person means an individual, firm, corporation, partnership, 
association, State, municipality, commission, or political subdivision 
of a State, or any interstate body, as well as a department, agency, or 
instrumentality of the executive, legislative or judicial branch of the 
Federal Government.
    Petroleum oil means any oil extracted or derived from geological 
hydrocarbon deposits, including fractions thereof.
    Qualified individual means an individual familiar with the response 
plan, trained in his or her responsibilities in implementing the plan, 
and authorized, on behalf of the owner or operator, to initiate all 
response activities identified in the plan, to enter into response-
related contracts and obligate funds for such contracts, and to act as a 
liaison with the on-scene coordinator and other responsible officials. 
The qualified individual must be available at all times the owner or 
operator is engaged in transportation subject to part 130 (alone or in 
conjunction with an equally qualified alternate), must be fluent in 
English, and must have in his or her possession documentation of the 
required authority.
    Transports or Transportation means any movement of oil by highway or 
rail, and any loading, unloading, or storage incidental thereto.
    Vegetable oil means a non-petroleum oil or fat derived from plant 
seeds, nuts, kernels or fruits, not specifically identified elsewhere in 
this part.
    Worst-case discharge means ``the largest foreseeable discharge in 
adverse weather conditions,'' as defined at 33 U.S.C. 1321(a)(24). The 
largest foreseeable discharge from a motor vehicle or rail car is the 
capacity of the cargo container. The term ``maximum potential 
discharge,'' used in Sec. 130.31(a), is synonymous with ``worst-case 
discharge.''

[Amdt. 130-2, 61 FR 30541, June 17, 1996, as amended by 66 FR 45378, 
Aug. 28, 2001; 67 FR 61011, Sept. 27, 2002; 69 FR 18803, Apr. 9, 2004]



Sec. 130.11  Communication requirements.

    (a) No person may offer oil subject to this part for transportation 
unless that person provides the person accepting the oil for 
transportation a document indicating the shipment contains oil.
    (b) No person may transport oil subject to this part unless a 
readily available document indicating that the shipment contains oil is 
in the possession of the transport vehicle operator during 
transportation.
    (c) A material subject to the requirements of this part need not be 
specifically identified as oil when the shipment document accurately 
describes the material as: aviation fuel, diesel fuel, fuel oil, 
gasoline, jet fuel, kerosene, motor fuel, or petroleum.



Sec. 130.21  Packaging requirements.

    Each packaging used for the transportation of oil subject to this 
part

[[Page 83]]

must be designed, constructed, maintained, closed, and loaded so that, 
under conditions normally incident to transportation, there will be no 
release of oil to the environment.



Sec. 130.31  Response plans.

    (a) No person may transport oil subject to this part unless that 
person has a current basic written plan that:
    (1) Sets forth the manner of response to discharges that may occur 
during transportation;
    (2) Takes into account the maximum potential discharge of the 
contents from the packaging;
    (3) Identifies private personnel and equipment available to respond 
to a discharge;
    (4) Identifies the appropriate persons and agencies (including their 
telephone numbers) to be contacted in regard to such a discharge and its 
handling, including the National Response Center; and
    (5) For each motor carrier, is retained on file at that person's 
principal place of business and at each location where dispatching of 
motor vehicles occurs; and for each railroad, is retained on file at 
that person's principal place of business and at the dispatcher's 
office.
    (b) No person may transport an oil subject to this part in a 
quantity greater than 1,000 barrels (42,000 gallons) unless that person 
has a current comprehensive written plan that:
    (1) Conforms with all requirements specified in paragraph (a) of 
this section;
    (2) Is consistent with the requirements of the National Contingency 
Plan (40 CFR part 300) and Area Contingency Plans;
    (3) Identifies the qualified individual having full authority to 
implement removal actions, and requires immediate communications between 
that individual and the appropriate Federal official and the persons 
providing spill response personnel and equipment;
    (4) Identifies, and ensures by contract or other means the 
availability of, private personnel (including address and phone number), 
and the equipment necessary to remove, to the maximum extent 
practicable, a worst case discharge (including a discharge resulting 
from fire or explosion) and to mitigate or prevent a substantial threat 
of such a discharge;
    (5) Describes the training, equipment testing, periodic unannounced 
drills, and response actions of facility personnel, to be carried out 
under the plan to ensure the safety of the facility and to mitigate or 
prevent the discharge, or the substantial threat of such a discharge; 
and
    (6) Is submitted, and resubmitted in the event of any significant 
change, to the Federal Railroad Administrator (for tank cars), or to the 
Federal Highway Administrator (for cargo tanks) at East Building, 1200 
New Jersey Avenue, SE., Washington, DC 20590-0001.

(Approved by the Office of Management and Budget under control number 
2137-0591)

[Amdt. 130-2, 61 FR 30541, June 17, 1996, as amended at 72 FR 55683, 
Oct. 1, 2007; 76 FR 56311, Sept. 13, 2011]



Sec. 130.33  Response plan implementation.

    If, during transportation of oil subject to this part, a discharge 
occurs--into or on the navigable waters of the United States; on the 
adjoining shorelines to the navigable waters; or that may affect natural 
resources belonging to, appertaining to, or under the exclusive 
management authority of, the United States--the person transporting the 
oil shall implement the plan required by Sec. 130.31, in a manner 
consistent with the National Contingency Plan, 40 CFR part 300, or as 
otherwise directed by the Federal on-scene coordinator.

[[Page 84]]



              SUBCHAPTER C_HAZARDOUS MATERIALS REGULATIONS



PART 171_GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS--Table of Contents



Sec.

   Subpart A_Applicability, General Requirements, and North American 
                                Shipments

171.1 Applicability of Hazardous Materials Regulations (HMR) to persons 
          and functions.
171.2 General requirements.
171.3 Hazardous waste.
171.4 Marine pollutants.
171.6 Control numbers under the Paperwork Reduction Act.
171.7 Reference material.
171.8 Definitions and abbreviations.
171.9 Rules of construction.
171.10 Units of measure.
171.11 [Reserved]
171.12 North American Shipments.
171.12a [Reserved]
171.14 [Reserved]

     Subpart B_Incident Reporting, Notification, BOE Approvals and 
                              Authorization

171.15 Immediate notice of certain hazardous materials incidents.
171.16 Detailed hazardous materials incident reports.
171.17-171.18 [Reserved]
171.19 Approvals or authorizations issued by the Bureau of Explosives.
171.20 Submission of Examination Reports.
171.21 Assistance in investigations and special studies.

 Subpart C_Authorization and Requirements for the Use of International 
                   Transport Standards and Regulations

171.22 Authorization and conditions for the use of international 
          standards and regulations.
171.23 Requirements for specific materials and packagings transported 
          under the ICAO Technical Instructions, IMDG Code, Transport 
          Canada TDG Regulations, or the IAEA Regulations.
171.24 Additional requirements for the use of the ICAO Technical 
          Instructions.
171.25 Additional requirements for the use of the IMDG Code.
171.26 Additional requirements for the use of the IAEA Regulations.

    Authority: 49 U.S.C. 5101-5128, 44701; 49 CFR 1.45 and 1.53; Pub. L. 
101-410 section 4 (28 U.S.C. 2461 note); Pub. L. 104-134 section 31001.

    Editorial Note: Nomenclature changes to part 171 appear at 70 FR 
56090, Sept. 23, 2005.



   Subpart A_Applicability, General Requirements, and North American 

                                Shipments



Sec. 171.1  Applicability of Hazardous Materials Regulations (HMR) to persons 

and functions.

    Federal hazardous materials transportation law (49 U.S.C. 5101 et 
seq.) directs the Secretary of Transportation to establish regulations 
for the safe and secure transportation of hazardous materials in 
commerce, as the Secretary considers appropriate. The Secretary is 
authorized to apply these regulations to persons who transport hazardous 
materials in commerce. In addition, the law authorizes the Secretary to 
apply these regulations to persons who cause hazardous materials to be 
transported in commerce. The law also authorizes the Secretary to apply 
these regulations to persons who manufacture or maintain a packaging or 
a component of a packaging that is represented, marked, certified, or 
sold as qualified for use in the transportation of a hazardous material 
in commerce. Federal hazardous material transportation law also applies 
to anyone who indicates by marking or other means that a hazardous 
material being transported in commerce is present in a package or 
transport conveyance when it is not, and to anyone who tampers with a 
package or transport conveyance used to transport hazardous materials in 
commerce or a required marking, label, placard, or shipping description. 
Regulations prescribed in accordance with Federal hazardous materials 
transportation law shall govern safety aspects, including security, of 
the transportation of hazardous materials that the Secretary considers 
appropriate. In 49 CFR 1.53, the Secretary delegated authority to issue 
regulations for the safe and secure transportation of hazardous 
materials in commerce to the Pipeline and Hazardous Materials Safety 
Administrator. The Administrator issues the Hazardous Materials 
Regulations (HMR; 49 CFR

[[Page 85]]

Parts 171 through 180) under that delegated authority. This section 
addresses the applicability of the HMR to packagings represented as 
qualified for use in the transportation of hazardous materials in 
commerce and to pre-transportation and transportation functions.
    (a) Packagings. Requirements in the HMR apply to each person who 
manufactures, fabricates, marks, maintains, reconditions, repairs, or 
tests a packaging or a component of a packaging that is represented, 
marked, certified, or sold as qualified for use in the transportation of 
a hazardous material in commerce, including each person under contract 
with any department, agency, or instrumentality of the executive, 
legislative, or judicial branch of the Federal government who 
manufactures, fabricates, marks, maintains, reconditions, repairs, or 
tests a packaging or a component of a packaging that is represented, 
marked, certified, or sold as qualified for use in the transportation of 
a hazardous material in commerce.
    (b) Pre-transportation functions. Requirements in the HMR apply to 
each person who offers a hazardous material for transportation in 
commerce, causes a hazardous material to be transported in commerce, or 
transports a hazardous material in commerce and who performs or is 
responsible for performing a pre-transportation function, including each 
person performing pre-transportation functions under contract with any 
department, agency, or instrumentality of the executive, legislative, or 
judicial branch of the Federal government. Pre-transportation functions 
include, but are not limited to, the following:
    (1) Determining the hazard class of a hazardous material.
    (2) Selecting a hazardous materials packaging.
    (3) Filling a hazardous materials packaging, including a bulk 
packaging.
    (4) Securing a closure on a filled or partially filled hazardous 
materials package or container or on a package or container containing a 
residue of a hazardous material.
    (5) Marking a package to indicate that it contains a hazardous 
material.
    (6) Labeling a package to indicate that it contains a hazardous 
material.
    (7) Preparing a shipping paper.
    (8) Providing and maintaining emergency response information.
    (9) Reviewing a shipping paper to verify compliance with the HMR or 
international equivalents.
    (10) For each person importing a hazardous material into the United 
States, providing the shipper with timely and complete information as to 
the HMR requirements that will apply to the transportation of the 
material within the United States.
    (11) Certifying that a hazardous material is in proper condition for 
transportation in conformance with the requirements of the HMR.
    (12) Loading, blocking, and bracing a hazardous materials package in 
a freight container or transport vehicle.
    (13) Segregating a hazardous materials package in a freight 
container or transport vehicle from incompatible cargo.
    (14) Selecting, providing, or affixing placards for a freight 
container or transport vehicle to indicate that it contains a hazardous 
material.
    (c) Transportation functions. Requirements in the HMR apply to 
transportation of a hazardous material in commerce and to each person 
who transports a hazardous material in commerce, including each person 
under contract with any department, agency, or instrumentality of the 
executive, legislative, or judicial branch of the Federal government who 
transports a hazardous material in commerce. Transportation of a 
hazardous material in commerce begins when a carrier takes physical 
possession of the hazardous material for the purpose of transporting it 
and continues until the package containing the hazardous material is 
delivered to the destination indicated on a shipping document, package 
marking, or other medium, or, in the case of a rail car, until the car 
is delivered to a private track or siding. For a private motor carrier, 
transportation of a hazardous material in commerce begins when a motor 
vehicle driver takes possession of a hazardous

[[Page 86]]

material for the purpose of transporting it and continues until the 
driver relinquishes possession of the package containing the hazardous 
material at its destination and is no longer responsible for performing 
functions subject to the HMR with respect to that particular package. 
Transportation of a hazardous material in commerce includes the 
following:
    (1) Movement. Movement of a hazardous material by rail car, 
aircraft, motor vehicle, or vessel (except as delegated by Department of 
Homeland Security Delegation No. 0170 at 2(103)).
    (2) Loading incidental to movement of a hazardous material. Loading 
of packaged or containerized hazardous material onto a transport 
vehicle, aircraft, or vessel for the purpose of transporting it, 
including blocking and bracing a hazardous materials package in a 
freight container or transport vehicle, and segregating a hazardous 
materials package in a freight container or transport vehicle from 
incompatible cargo, when performed by carrier personnel or in the 
presence of carrier personnel. For a bulk packaging, loading incidental 
to movement is filling the packaging with a hazardous material for the 
purpose of transporting it when performed by carrier personnel or in the 
presence of carrier personnel (except as delegated by Department of 
Homeland Security Delegation No. 0170 at 2(103)), including 
transloading.
    (3) Unloading incidental to movement of a hazardous material. 
Removing a package or containerized hazardous material from a transport 
vehicle, aircraft, or vessel; or for a bulk packaging, emptying a 
hazardous material from the bulk packaging after the hazardous material 
has been delivered to the consignee when performed by carrier personnel 
or in the presence of carrier personnel or, in the case of a private 
motor carrier, while the driver of the motor vehicle from which the 
hazardous material is being unloaded immediately after movement is 
completed is present during the unloading operation. (Emptying a 
hazardous material from a bulk packaging while the packaging is on board 
a vessel is subject to separate regulations as delegated by Department 
of Homeland Security Delegation No. 0170 at 2(103).) Unloading 
incidental to movement includes transloading.
    (4) Storage incidental to movement of a hazardous material. Storage 
of a transport vehicle, freight container, or package containing a 
hazardous material by any person between the time that a carrier takes 
physical possession of the hazardous material for the purpose of 
transporting it until the package containing the hazardous material has 
been delivered to the destination indicated on a shipping document, 
package marking, or other medium, or, in the case of a private motor 
carrier, between the time that a motor vehicle driver takes physical 
possession of the hazardous material for the purpose of transporting it 
until the driver relinquishes possession of the package at its 
destination and is no longer responsible for performing functions 
subject to the HMR with respect to that particular package.
    (i) Storage incidental to movement includes--
    (A) Storage at the destination shown on a shipping document, 
including storage at a transloading facility, provided the original 
shipping documentation identifies the shipment as a through-shipment and 
identifies the final destination or destinations of the hazardous 
material; and
    (B) A rail car containing a hazardous material that is stored on 
track that does not meet the definition of ``private track or siding'' 
in Sec. 171.8, even if the car has been delivered to the destination 
shown on the shipping document.
    (ii) Storage incidental to movement does not include storage of a 
hazardous material at its final destination as shown on a shipping 
document.
    (d) Functions not subject to the requirements of the HMR. The 
following are examples of activities to which the HMR do not apply:
    (1) Storage of a freight container, transport vehicle, or package 
containing a hazardous material at an offeror facility prior to a 
carrier taking possession of the hazardous material for movement in 
transportation in commerce or, for a private motor carrier, prior to a 
motor vehicle driver

[[Page 87]]

taking physical possession of the hazardous material for movement in 
transportation in commerce.
    (2) Unloading of a hazardous material from a transport vehicle or a 
bulk packaging performed by a person employed by or working under 
contract to the consignee following delivery of the hazardous material 
by the carrier to its destination and departure from the consignee's 
premises of the carrier's personnel or, in the case of a private 
carrier, departure of the driver from the unloading area.
    (3) Storage of a freight container, transport vehicle, or package 
containing a hazardous material after its delivery by a carrier to the 
destination indicated on a shipping document, package marking, or other 
medium, or, in the case of a rail car, storage of a rail car on private 
track.
    (4) Rail and motor vehicle movements of a hazardous material 
exclusively within a contiguous facility boundary where public access is 
restricted, except to the extent that the movement is on or crosses a 
public road or is on track that is part of the general railroad system 
of transportation, unless access to the public road is restricted by 
signals, lights, gates, or similar controls.
    (5) Transportation of a hazardous material in a motor vehicle, 
aircraft, or vessel operated by a Federal, state, or local government 
employee solely for noncommercial Federal, state, or local government 
purposes.
    (6) Transportation of a hazardous material by an individual for non-
commercial purposes in a private motor vehicle, including a leased or 
rented motor vehicle.
    (7) Any matter subject to the postal laws and regulations of the 
United States.
    (e) Requirements of other Federal agencies. Each facility at which 
pre-transportation or transportation functions are performed in 
accordance with the HMR may be subject to applicable standards and 
regulations of other Federal agencies.
    (f) Requirements of state and local government agencies. (1) Under 
49 U.S.C. 5125, a requirement of a state, political subdivision of a 
state, or an Indian tribe is preempted, unless otherwise authorized by 
another Federal statute or DOT issues a waiver of preemption, if--
    (i) Complying with both the non-Federal requirement and Federal 
hazardous materials transportation law, the regulations issued under 
Federal hazardous material transportation law or a hazardous material 
transportation security regulation or directive issued by the Secretary 
of Homeland Security is not possible;
    (ii) The non-Federal requirement, as applied or enforced, is an 
obstacle to accomplishing and carrying out Federal hazardous materials 
transportation law, the regulations issued under Federal hazardous 
material transportation law, or a hazardous material transportation 
security regulation or directive issued by the Secretary of Homeland 
Security;
    (iii) The non-Federal requirement is not substantively the same as a 
provision of Federal hazardous materials transportation law, the 
regulations issued under Federal hazardous material transportation law, 
or a hazardous material transportation security regulation or directive 
issued by the Secretary of Homeland Security with respect to--
    (A) The designation, description, and classification of hazardous 
material;
    (B) The packing, repacking, handling, labeling, marking, and 
placarding of hazardous material;
    (C) The preparation, execution, and use of shipping documents 
related to hazardous material and requirements related to the number, 
contents, and placement of those documents;
    (D) The written notification, recording, and reporting of the 
unintentional release of hazardous material; or
    (E) The design, manufacturing, fabricating, marking, maintenance, 
reconditioning, repairing, or testing of a package or container 
represented, marked, certified, or sold as qualified for use in 
transporting hazardous material.
    (iv) A non-Federal designation, limitation or requirement on highway 
routes over which hazardous material may or may not be transported does 
not comply with the regulations in subparts C and D of part 397 of this 
title; or

[[Page 88]]

    (v) A fee related to the transportation of a hazardous material is 
not fair or is used for a purpose that is not related to transporting 
hazardous material, including enforcement and planning, developing, and 
maintaining a capability for emergency response.
    (2) Subject to the limitations in paragraph (f)(1) of this section, 
each facility at which functions regulated under the HMR are performed 
may be subject to applicable laws and regulations of state and local 
governments and Indian tribes.
    (3) The procedures for DOT to make administrative determinations of 
preemption are set forth in subpart E of part 397 of this title with 
respect to non-Federal requirements on highway routing (paragraph 
(f)(1)(iv) of this section) and in subpart C of part 107 of this chapter 
with respect to all other non-Federal requirements.
    (g) Penalties for noncompliance. Each person who knowingly violates 
a requirement of the Federal hazardous material transportation law, an 
order issued under Federal hazardous material transportation law, 
subchapter A of this chapter, or a special permit or approval issued 
under subchapter A or C of this chapter is liable for a civil penalty of 
not more than $55,000 and not less than $250 for each violation, except 
the maximum civil penalty is $110,000 if the violation results in death, 
serious illness or severe injury to any person or substantial 
destruction of property, and a minimum $495 civil penalty applies to a 
violation relating to training. When a violation is a continuing one and 
involves transporting of hazardous material or causing them to be 
transported, each day of the violation is a separate offense. Each 
person who knowingly violates Sec. 171.2(l) or willfully or recklessly 
violates a provision of the Federal hazardous material transportation 
law, an order issued under Federal hazardous material transportation 
law, subchapter A of this chapter, or a special permit or approval 
issued under subchapter A or C of this chapter, shall be fined under 
title 18, United States Code, or imprisoned for not more than 5 years, 
or both, except the maximum amount of imprisonment shall be 10 years in 
any case in which a violation involves the release of a hazardous 
material which results in death or bodily injury to any person.

[68 FR 61937, Oct. 30, 2003; 70 FR 20031, Apr. 15, 2005, as amended at 
70 FR 73162, Dec. 9, 2005; 71 FR 8488, Feb. 17, 2006; 71 FR 44931, Aug. 
8, 2006; 74 FR 68702, Dec. 29, 2009; 75 FR 53596, Sept. 1, 2010]



Sec. 171.2  General requirements.

    (a) Each person who performs a function covered by this subchapter 
must perform that function in accordance with this subchapter.
    (b) Each person who offers a hazardous material for transportation 
in commerce must comply with all applicable requirements of this 
subchapter, or an exemption or special permit, approval, or registration 
issued under this subchapter or under subchapter A of this chapter. 
There may be more than one offeror of a shipment of hazardous materials. 
Each offeror is responsible for complying with the requirements of this 
subchapter, or an exemption or special permit, approval, or registration 
issued under this subchapter or subchapter A of this chapter, with 
respect to any pre-transportation function that it performs or is 
required to perform; however, each offeror is responsible only for the 
specific pre-transportation functions that it performs or is required to 
perform, and each offeror may rely on information provided by another 
offeror, unless that offeror knows or, a reasonable person, acting in 
the circumstances and exercising reasonable care, would have knowledge 
that the information provided by the other offeror is incorrect.
    (c) Each person who performs a function covered by or having an 
effect on a specification or activity prescribed in part 178, 179, or 
180 of this subchapter, an approval issued under this subchapter, or an 
exemption or special permit issued under subchapter A of this chapter, 
must perform the function in accordance with that specification, 
approval, an exemption or special permit, as appropriate.
    (d) No person may offer or accept a hazardous material for 
transportation in commerce or transport a hazardous material in commerce 
unless that person is registered in conformance with

[[Page 89]]

subpart G of part 107 of this chapter, if applicable.
    (e) No person may offer or accept a hazardous material for 
transportation in commerce unless the hazardous material is properly 
classed, described, packaged, marked, labeled, and in condition for 
shipment as required or authorized by applicable requirements of this 
subchapter or an exemption or special permit, approval, or registration 
issued under this subchapter or subchapter A of this chapter.
    (f) No person may transport a hazardous material in commerce unless 
the hazardous material is transported in accordance with applicable 
requirements of this subchapter, or an exemption or special permit, 
approval, or registration issued under this subchapter or subchapter A 
of this chapter. Each carrier who transports a hazardous material in 
commerce may rely on information provided by the offeror of the 
hazardous material or a prior carrier, unless the carrier knows or, a 
reasonable person, acting in the circumstances and exercising reasonable 
care, would have knowledge that the information provided by the offeror 
or prior carrier is incorrect.
    (g) No person may represent, mark, certify, sell, or offer a 
packaging or container as meeting the requirements of this subchapter 
governing its use in the transportation of a hazardous material in 
commerce unless the packaging or container is manufactured, fabricated, 
marked, maintained, reconditioned, repaired, and retested in accordance 
with the applicable requirements of this subchapter. No person may 
represent, mark, certify, sell, or offer a packaging or container as 
meeting the requirements of an exemption, a special permit, approval, or 
registration issued under this subchapter or subchapter A of this 
chapter unless the packaging or container is manufactured, fabricated, 
marked, maintained, reconditioned, repaired, and retested in accordance 
with the applicable requirements of the exemption, special permit, 
approval, or registration issued under this subchapter or subchapter A 
of this chapter. The requirements of this paragraph apply whether or not 
the packaging or container is used or to be used for the transportation 
of a hazardous material.
    (h) The representations, markings, and certifications subject to the 
prohibitions of paragraph (g) of this section include:
    (1) Specification identifications that include the letters ``ICC'', 
``DOT'', ``CTC'', ``MC'', or ``UN'';
    (2) Exemption, special permit, approval, and registration numbers 
that include the letters ``DOT'', ``EX'', ``M'', or ``R''; and
    (3) Test dates associated with specification, registration, 
approval, retest, exemption, or special permit markings indicating 
compliance with a test or retest requirement of the HMR, or an 
exemption, special permit, approval, or registration issued under the 
HMR or under subchapter A of this chapter.
    (i) No person may certify that a hazardous material is offered for 
transportation in commerce in accordance with the requirements of this 
subchapter unless the hazardous material is properly classed, described, 
packaged, marked, labeled, and in condition for shipment as required or 
authorized by applicable requirements of this subchapter or an exemption 
or special permit, approval, or registration issued under this 
subchapter or subchapter A of this chapter. Each person who offers a 
package containing a hazardous material for transportation in commerce 
in accordance with the requirements of this subchapter or an exemption 
or special permit, approval, or registration issued under this 
subchapter or subchapter A of this chapter, must assure that the package 
remains in condition for shipment until it is in the possession of the 
carrier.
    (j) No person may, by marking or otherwise, represent that a 
container or package for transportation of a hazardous material is safe, 
certified, or in compliance with the requirements of this chapter unless 
it meets the requirements of all applicable regulations issued under 
Federal hazardous material transportation law.
    (k) No person may, by marking or otherwise, represent that a 
hazardous material is present in a package, container, motor vehicle, 
rail car, aircraft, or vessel if the hazardous material is not present.

[[Page 90]]

    (l) No person may alter, remove, deface, destroy, or otherwise 
unlawfully tamper with any marking, label, placard, or description on a 
document required by Federal hazardous material transportation law or 
the regulations issued under Federal hazardous material transportation 
law. No person may alter, deface, destroy, or otherwise unlawfully 
tamper with a package, container, motor vehicle, rail car, aircraft, or 
vessel used for the transportation of hazardous materials.
    (m) No person may falsify or alter an exemption or special permit, 
approval, registration, or other grant of authority issued under this 
subchapter or subchapter A of this chapter. No person may offer a 
hazardous material for transportation or transport a hazardous material 
in commerce under an exemption or special permit, approval, registration 
or other grant of authority issued under this subchapter or subchapter A 
of this chapter if such grant of authority has been altered without the 
consent of the issuing authority. No person may represent, mark, 
certify, or sell a packaging or container under an exemption or special 
permit, approval, registration or other grant of authority issued under 
this subchapter or subchapter A of this chapter if such grant of 
authority has been altered without the consent of the issuing authority.

[68 FR 61937, Oct. 30, 2003, as amended at 70 FR 43643, July 28, 2005; 
70 FR 73162, Dec. 9, 2005]



Sec. 171.3  Hazardous waste.

    (a) No person may offer for transportation or transport a hazardous 
waste (as defined in Sec. 171.8 of this subchapter) in interstate or 
intrastate commerce except in accordance with the requirements of this 
subchapter.
    (b) No person may accept for transportation, transport, or deliver a 
hazardous waste for which a manifest is required unless that person:
    (1) Has marked each motor vehicle used to transport hazardous waste 
in accordance with Sec. 390.21 of this title even though placards may 
not be required;
    (2) Complies with the requirements for manifests set forth in Sec. 
172.205 of this subchapter; and
    (3) Delivers, as designated on the manifest by the generator, the 
entire quantity of the waste received from the generator or a 
transporter to:
    (i) The designated facility or, if not possible, to the designated 
alternate facility;
    (ii) The designated subsequent carrier; or
    (iii) A designated place outside the United States.

    Note: Federal law specifies penalties up to $250,000 fine for an 
individual and $500,000 for a company and 5 years imprisonment for the 
willful discharge of hazardous waste at other than designated 
facilities. 49 U.S.C. 5124.

    (c) If a discharge of hazardous waste or other hazardous material 
occurs during transportation, and an official of a State or local 
government or a Federal agency, acting within the scope of his official 
responsibilities, determines that immediate removal of the waste is 
necessary to prevent further consequence, that official may authorize 
the removal of the waste without the preparation of a manifest. [Note: 
In such cases, EPA does not require carriers to have EPA identification 
numbers.]

    Note 1: EPA requires shippers (generators) and carriers 
(transporters) of hazardous wastes to have identification numbers which 
must be displayed on hazardous waste manifests. See 40 CFR parts 262 and 
263. (Identification number application forms may be obtained from EPA 
regional offices.)
    Note 2: In 40 CFR part 263, the EPA sets forth requirements for the 
cleanup of releases of hazardous wastes.

[Amdt. 171-53, 45 FR 34586, May 22, 1980, as amended by Amdt. 171-53, 45 
FR 74648, Nov. 10, 1980; Amdt. 171-78, 49 FR 10510, Mar. 20, 1984; Amdt. 
171-107, 54 FR 40068, Sept. 29, 1989; Amdt. 171-111, 55 FR 52466, Dec. 
21, 1990; 56 FR 66157, Dec. 20, 1991; Amdt. 171-2, 59 FR 49132, Sept. 
26, 1994; Amdt. 171-141, 61 FR 21102, May 9, 1996; 73 FR 57004, Oct. 1, 
2008]



Sec. 171.4  Marine pollutants.

    (a) Except as provided in paragraph (c) of this section, no person 
may offer for transportation or transport a marine pollutant, as defined 
in Sec. 171.8, in intrastate or interstate commerce except in 
accordance with the requirements of this subchapter.

[[Page 91]]

    (b) The requirements of this subchapter for the transportation of 
marine pollutants are based on the provisions of Annex III of the 1973 
International Convention for Prevention of Pollution from Ships, as 
modified by the Protocol of 1978 (MARPOL 73/78).
    (c) Exceptions. Except when all or part of the transportation is by 
vessel, the requirements of this subchapter specific to marine 
pollutants do not apply to non-bulk packagings transported by motor 
vehicle, rail car or aircraft.

[Amdt. 171-116, 57 FR 52934, Nov. 5, 1993, as amended by Amdt. 107-39, 
61 FR 51337, Oct. 1, 1996; 73 FR 4712, Jan. 28, 2008]



Sec. 171.6  Control numbers under the Paperwork Reduction Act.

    (a) Purpose and scope. This section collects and displays the 
control numbers assigned to the HMR collections of information by the 
Office of Management and Budget (OMB) under the Paperwork Reduction Act 
of 1995. This section complies with the requirements of 5 CFR 1320.7(f), 
1320.12, 1320.13 and 1320.14 (OMB regulations implementing the Paperwork 
Reduction Act of 1995) for the display of control numbers assigned by 
OMB to collections of information of the HMR.
    (b) OMB control numbers. The table in paragraph (b)(2) of this 
section sets forth the control numbers assigned to collection of 
information in the HMR by the Office of Management and Budget (OMB) 
under the Paperwork Reduction Act of 1995.
    (1) Column 1 lists the OMB control number assigned to the HMR 
collections of information. Column 2 contains the Report Title of the 
approved collection of information. Column 3 lists the part(s) or 
section(s) in 49 CFR identified or described in the collection of 
information.
    (2) Table.

------------------------------------------------------------------------
                                                    Title 49 CFR part or
                                                       section where
  Current OMB control No.           Title              identified and
                                                         described
------------------------------------------------------------------------
2137-0014.................  Cargo Tank             Sec. Sec.  107.503,
                             Specification          107.504, 178.320,
                             Requirements.          178.337, 178.338,
                                                    178.345, 180.407,
                                                    180.409, 180.413,
                                                    180.417.
2137-0018.................  Inspection and         Sec. Sec.  173.24,
                             Testing of Portable    173.32, 178.3,
                             Tanks and              178.255, 178.273,
                             Intermediate Bulk      178.274, 178.703,
                             Containers.            178.801, 180.352,
                                                    180.605.
2137-0022.................  Testing, Inspection,   Sec. Sec.  173.5b,
                             and Marking            173.302a, 173.303,
                             Requirements for       173.304, 173.309,
                             Cylinders.             178.2, 178.3,
                                                    178.35, 178.44,
                                                    178.45, 178.46,
                                                    178.57, 178.59,
                                                    178.60, 178.61,
                                                    178.68, 180.205,
                                                    180.207, 180.209,
                                                    180.211, 180.213,
                                                    180.215, 180.217,
                                                    Appendix C to Part
                                                    180.
2137-0034.................  Hazardous Materials    Sec. Sec.  172.200,
                             Shipping Papers and    172.201, 172.202,
                             Emergency Response     172.203, 172.204,
                             Information.           172.505, 172.600,
                                                    172.602, 172.604,
                                                    172.606, 173.6,
                                                    173.7, 173.22,
                                                    173.56, 174.24,
                                                    174.26, 174.114,
                                                    175.30, 175.31,
                                                    175.33, 176.24,
                                                    176.27, 176.30,
                                                    176.36, 176.89,
                                                    177.817.
2137-0039.................  Hazardous Materials    Sec. Sec.  171.15,
                             Incidents Reports.     171.16, 171.21.
2137-0051.................  Rulemaking and         Sec. Sec.  105.30,
                             Special Permit         105.40, 106.95,
                             Petitions.             106.110, 107.105,
                                                    107.107, 107.109,
                                                    107.113, 107.117,
                                                    107.121, 107.123,
                                                    107.125, 107.205,
                                                    107.211, 107.215,
                                                    107.217, 107.219,
                                                    107.221, 107.223.
2137-0510.................  RAM Transportation     Part 173, Subpart I,
                             Requirements.          Sec. Sec.  173.22,
                                                    173.411, 173.415,
                                                    173.416, 173.417,
                                                    173.457, 173.471,
                                                    173.472, 173.473,
                                                    173.476.
2137-0542.................  Flammable Cryogenic    Sec. Sec.  173.318,
                             Liquids.               177.816, 177.840,
                                                    180.405.

[[Page 92]]

 
2137-0557.................  Approvals for          Sec. Sec.  107.402,
                             Hazardous Materials    107.403, 107.405,
                                                    107.502, 107.503,
                                                    107.705, 107.713,
                                                    107.715, 107.717,
                                                    107.803, 107.805,
                                                    107.807, 110.30,
                                                    172.101, 172.102,
                                                    Special Provisions
                                                    19, 26, 53, 55, 60,
                                                    105, 118, 121, 125,
                                                    129, 131, 133, 136,
                                                    B45, B55, B61, B69,
                                                    B77, B81, N10, N72,
                                                    173.2a, 173.4,
                                                    173.7, 173.21,
                                                    173.22, 173.24,
                                                    173.31, 173.38,
                                                    173.51, 173.56,
                                                    173.58, 173.59,
                                                    173.124, 173.128,
                                                    173.159, 173.166,
                                                    173.171, 173.214,
                                                    173.222, 173.224,
                                                    173.225, 173.245,
                                                    173.301, 173.305,
                                                    173.306, 173.314,
                                                    173.315, 173.316,
                                                    173.318, 173.334,
                                                    173.340, 173.411,
                                                    173.433, 173.457,
                                                    173.471, 173.472,
                                                    173.476, 174.50,
                                                    174.63, 175.8,
                                                    175.85, 175.701,
                                                    175.703, 176.168,
                                                    176.340, 176.704,
                                                    178.3, 178.35,
                                                    178.47, 178.53,
                                                    178.273, 178.274,
                                                    178.503, 178.509,
                                                    178.605, 178.606,
                                                    178.608, 178.801,
                                                    178.813, 180.213.
2137-0559.................  (Rail Carriers and     Sec. Sec.  172.102,
                             Tank Car Tank          Special provisions:
                             Requirements)          B45, B46, B55, B61,
                             Requirements for       B69, B77, B78, B81;
                             Rail Tank Car Tanks--  173.10, 173.31,
                             Transportation of      174.20, 174.50,
                             Hazardous Materials    174.63, 174.104,
                             by Rail..              174.114, 174.204,
                                                    179.3, 179.4, 179.5,
                                                    179.6, 179.7,
                                                    179.11, 179.18,
                                                    179.22, 179.100-9,
                                                    179.100-12, 179.100-
                                                    13, 179.100-16,
                                                    179.100-17, 179.102-
                                                    4, 179.102-17,
                                                    179.103-1, 179.103-
                                                    2, 179.103-3,
                                                    179.103-5, 179.200-
                                                    10, 179.200-14,
                                                    179.200-15, 179.200-
                                                    16, 179.200-17,
                                                    179.200-19, 179.201-
                                                    3, 179.201-8,
                                                    179.201-9, 179.220-
                                                    4, 179.220-7,
                                                    179.220-8, 179.220-
                                                    13, 179.220-15,
                                                    179.220-17, 179.220-
                                                    18, 179.220-20,
                                                    179.220-22, 179.300-
                                                    3, 179.300-7,
                                                    179.300-9, 179.300-
                                                    12, 179.300-13,
                                                    179.300-15, 179.300-
                                                    20, 179.400-3,
                                                    179.400-4, 179.400-
                                                    11, 179.400-13,
                                                    179.400-16, 179.400-
                                                    17, 179.400-19,
                                                    179.400-20, 179.500-
                                                    5, 179.500-8,
                                                    179.500-12, 179.500-
                                                    18, 180.505,
                                                    180.509, 180.515,
                                                    180.517.
2137-0572.................  Testing requirements   Sec. Sec.  173.168,
                             for non-bulk           178.2, 178.601,
                             packages.              Appendix C to Part
                                                    178, Appendix D to
                                                    Part 178.
2137-0582.................  Container              Sec. Sec.  176.27,
                             Certification          176.172.
                             Statement.
2137-0586.................  Hazardous Materials    Part 110.
                             Public Sector
                             Training and
                             Planning Grants.
2137-0591.................  Response Plans for     Part 130.
                             Shipments of Oil.
2137-0595.................  Cargo Tank Motor       Sec. Sec.  173.315,
                             Vehicles in            178.337-8, 178.337-
                             Liquefied Compressed   9, 180.405, 180.416.
                             Gas Service.
2137-0612.................  Hazardous Materials    Part 172, Subpart I,
                             Security Plans.        Sec. Sec.
                                                    172.800, 172.802,
                                                    172.804.
2137-0613.................  Subsidiary Hazard      Sec. Sec.  172.202,
                             Class and Number/      172.203
                             Type of Packagings.
2137-0620.................  Inspection and         Part 173, Subpart A,
                             Testing of Meter       Sec.  173.5a.
                             Provers.
2137-0621.................  Requirements for       Sec. Sec.  173.301,
                             United Nations (UN)    173.304, 173.304b,
                             Cylinders.             178.69, 178.70,
                                                    178.74, 178.75,
                                                    180.207, 180.209,
                                                    180.212, 180.215,
                                                    180.217.
------------------------------------------------------------------------


[Amdt. 171-111, 56 FR 66157]

    Editorial Note: For Federal Register citations affecting Sec. 
171.6, see the List of CFR Sections Affected which appears in the 
Finding Aids section of the printed volume and at www.fdsys.gov.



Sec. 171.7  Reference material.

    (a) Matter incorporated by reference--(1) General. There is 
incorporated, by reference in parts 170-189 of this subchapter, matter 
referred to that is not specifically set forth. This matter is hereby 
made a part of the regulations in parts 170-189 of this subchapter. The 
matter subject to change is incorporated only as it is in effect on the

[[Page 93]]

date of issuance of the regulation referring to that matter. The 
material listed in paragraph (a)(3) has been approved for incorporation 
by reference by the Director of the Federal Register in accordance with 
5 U.S.C 552(a) and 1 CFR part 51. Material is incorporated as it exists 
on the date of the approval and a notice of any change in the material 
will be published in the Federal Register. Matters referenced by 
footnote are included as part of the regulations of this subchapter.
    (2) Accessibility of materials. All incorporated matter is available 
for inspection at:
    (i) The Office of Hazardous Materials Safety, Office of Hazardous 
Materials Standards, East Building, PHH-10, 1200 New Jersey Avenue, SE., 
Washington, DC 20590-0001. For information on the availability of this 
material at PHH-10, call 1-800-467-4922, or go to: http://
www.phmsa.dot.gov; and
    (ii) The National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, call 202-741-
6030, or go to: http://www.archives.gov/federal--register/code--of--
federal--regulations/ibr--locations.html.
    (3) Table of material incorporated by reference. The following table 
sets forth material incorporated by reference. The first column lists 
the name and address of the organization from which the material is 
available and the name of the material. The second column lists the 
section(s) of this subchapter, other than Sec. 171.7, in which the 
matter is referenced. The second column is presented for information 
only and may not be all inclusive.

------------------------------------------------------------------------
           Source and name of material               49 CFR reference
------------------------------------------------------------------------
Air Transport Association of America, 1301
 Pennsylvania Avenue, N.W., Washington, DC 20004-
 1707:
    ATA Specification No. 300 Packaging of        172.102.
     Airline Supplies, Revision 19, July 31,
     1996.
The Aluminum Association, 1525 Wilson Blvd,
 Suite 6000, Arlington, VA 22209, telephone 703-
 358-2960, http://www.aluminum.org.
    Aluminum Standards and Data, Seventh          172.102; 178.65.
     Edition, June 1982.
    Welding Aluminum: Theory and Practice, 2002   178.68
     Fourth Edition.
American National Standards Institute, Inc., 25
 West 43rd Street, New York, NY 10036:
    ANSI/ASHRAE 15-94, Safety Code for            173.306; 173.307.
     Mechanical Refrigeration.
    ANSI B16.5-77, Steel Pipe Flanges, Flanged    178.360-4.
     Fittings.
    ANSI N14.1 Uranium Hexafluoride--Packaging    173.417; 173.420.
     for Transport, 1971, 1982, 1987, 1990, 1995
     and 2001 Editions.
American Petroleum Institute, 1220 L Street, NW,
 Washington, D.C. 20005-4070:
    API Recommended Practice Closures of          172.102.
     Underground Petroleum Storage Tanks, 3rd
     Edition, March 1996.
American Pyrotechnics Association (APA), P.O.
 Box 30438, Bethesda, MD 20824, (301) 907-8181,
 www.americanpyro.com:
    APA Standard 87-1, Standard for Construction  173.56.
     and Approval for Transportation of
     Fireworks, Novelties, and Theatrical
     Pyrotechnics, December 1, 2001 version.
American Society of Mechanical Engineers, ASME
 International, 22 Law Drive, P.O. Box 2900,
 Fairfield, NJ 07007-2900, telephone 1-800-843-
 2763 or 1-973-882-1170, http://www.asme.org:

[[Page 94]]

 
    `ASME Code'; ASME Code, Sections II (Parts A  172.102; 173.5b;
     and B), V, VIII (Division 1), and IX of       173.24b; 173.32;
     1998 Edition of American Society of           173.306; 173.315;
     Mechanical Engineers Boiler and Pressure      173.318; 173.420;
     Vessel Code.                                  178.245-1; 178.245-3;
                                                   178.245-4; 178.245-6;
                                                   178.245-7; 178.255-1;
                                                   178.255-2; 178.255-
                                                   14; 178.255-15;
                                                   178.270-2; 178.270-3;
                                                   178.270-7; 178.270-9;
                                                   178.270-11; 178.270-
                                                   12; 178.271-1;
                                                   178.272-1; 178.273;
                                                   178.274; 178.276;
                                                   178.277; 178.320;
                                                   178.337-1; 178.337-2;
                                                   178.337-3; 178.337-4;
                                                   178.337-6; 178.337-
                                                   16; 178.337-18;
                                                   178.338-1; 178.338-2;
                                                   178.338-3; 178.338-4;
                                                   178.338-5; 178.338-6;
                                                   178.338-13; 178.338-
                                                   16; 178.338-18;
                                                   178.338-19; 178.345-
                                                   1; 178.345-2; 178.345-
                                                   3; 178.345-4; 178.345-
                                                   7; 178.345-14;
                                                   178.345-15; 178.346-
                                                   1; 178.347-1; 178.348-
                                                   1; 179.400-3;
                                                   180.407.
    Pipeline Transportation Systems for Liquid    173.5a.
     Hydrocarbons and other Liquids, Chapters
     II, III, IV, V and VI, ASME B31.4-1998
     Edition.
American Society for Testing and Materials, 100
 Barr Harbor Drive, West Conshohocken, PA 1942,
 telephone (610) 832-9585, http://www.astm.org:
    Noncurrent ASTM Standards are available
     from: Engineering Societies Library, 354
     East 47th Street, New York, NY 10017
    ASTM A 20/A 20M-93a Standard Specification    178.337-2; 179.102-4;
     for General Requirements for Steel Plates     179.102-1; 179.102-
     for Pressure Vessels.                         17.
    ASTM A 47-68 Malleable Iron Castings........  179.200-15.
    ASTM A 53, ASTM A 53/A 53M-06a Standard       173.5b.
     Specification for Pipe, Steel, Black and
     Hot-Dipped, Zinc-Coated, Welded and
     Seamless.
    ASTM A 106, ASTM A 106/A 106M-06a Standard    173.5b.
     Specification for Seamless Carbon Steel
     Pipe for High-Temperature Service.

[[Page 95]]

 
    ASTM A 240/A 240M-99b Standard Specification  178.57; 178.358-5;
     for Heat-Resisting Chromium and Chromium-     179.100-7; 179.100-
     Nickel Stainless Steel Plate, Sheet and       10; 179.102-1;
     Strip for Pressure Vessels.                   179.102-4; 179.102-
                                                   17; 179.200-7;
                                                   179.201-5; 179.220-7;
                                                   179.300-7; 179.400-5.
    ASTM A 242-81 Standard Specification for      178.338-2.
     High-Strength Low-Alloy Structural Steel.
    ASTM A 262-93a Standard Practices for         179.100-7; 179.200-7;
     Detecting Susceptibility to Intergranular     179.201-4.
     Attack in Austenitic Stainless Steels.
    ASTM A 285-78 Pressure Vessel Plates, Carbon  179.300-7.
     Steel, Low- and Intermediate-Tensile
     Strength.
    ASTM A 300-58 Steel Plates for Pressure       178.337-2.
     Vessels for Service at Low Temperatures.
    ASTM A 302/A 302M-93 Standard Specification   179.100-7; 179.200-7;
     for Pressure Vessel Plates, Alloy Steel,      179.220-7.
     Manganese-Molybdenum and Manganese-
     Molybdenum Nickel.
    ASTM A 333-67 Seamless and Welded Steel Pipe  178.45.
     for Low-Temperature Service.
    ASTM A 370-94 Standard Test 179.102-1;        179.102-17.
     179.102-4; Methods and Definitions for
     Mechanical Testing of Steel Products.
    ASTM A 441-81 Standard Specification for      178.338-2.
     High-Strength Low-Alloy Structural
     Manganese Vanadium Steel.
    ASTM A 514-81 Standard Specification for      178.338-2.
     High-Yield Strength Quenched and Tempered
     Alloy Steel Plate, Suitable for Welding.
    ASTM A 515/A 515M-03 Standard Specification   179.300-7.
     for Pressure Vessel Plates, Carbon Steel,
     for Intermediate- and Higher-Temperature
     Service.
    ASTM A 516/A 516M-90 Standard Specification   178.337-2; 179.100-7;
     for Pressure Vessel Plates, Carbon Steel,     179.102-1; 179.102-2;
     for Moderate and Lower-Temperature Service.   179.102-4; 179.102-
                                                   17; 179.200-7;
                                                   179.220-7; 179.300-7.
    ASTM A 537/A 537M-91 Standard Specification   179.100-7; 179.102-4;
     for Pressure Vessel Plates, Heat-Treated,     179.102-17.
     Carbon-Manganese-Silicon Steel.
    ASTM A 572-82 Standard Specification for      178.338-2.
     High-Strength Low-Alloy Columbian-Vanadium
     Steels of Structural Quality.
    ASTM A 588-81 Standard Specification for      178.338-2.
     High-Strength Low-Alloy Structural Steel
     with 50 Ksi Minimum Yield Point to 4 in.
     Thick.
    ASTM A 606-75 Standard Specification for      178.338-2.
     Steel Sheet and Strip Hot- Rolled and Cold-
     Rolled, High-Strength, Low-Alloy, with
     Improved Atmospheric Corrosion Resistance,
     1975 (Reapproved 1981).
    ASTM A 607-98 Standard Specification for      178.338-2.
     Steel, Sheet and Strip, High-Strength, Low-
     Alloy, Columbium or Vanadium, or Both, Hot-
     Rolled and Cold-Rolled.
    ASTM A 612-72a High Strength Steel Plates     178.337-2.
     for Pressure Vessels for Moderate and Lower
     Temperature Service.
    ASTM A 633-79a Standard Specification for     178.338-2.
     Normalized High-Strength Low-Alloy
     Structural Steel, 1979 Edition.
    ASTM A 715-81 Standard Specification for      178.338-2.
     Steel Sheet and Strip, Hot-Rolled, High-
     Strength, Low-Alloy with Improved
     Formability, 1981.
    ASTM A 1008/A 1008M--03 Standard              178.338-2; 178.345-2
     Specification for Steel, Sheet, Cold-
     Rolled, Carbon, Structural, High-Strength
     Low-Alloy and High Strength Low-Alloy with
     Improved Formability.
    ASTM A 1011/A 1011M--03a Standard             178.338-2; 178.345-2
     Specification for Steel, Sheet and Strip,
     Hot-Rolled, Carbon, Structural, High-
     Strength Low Alloy and High Strength Low-
     Alloy with Improved Formability.
    ASTM B 162-93a Standard Specification for     173.249; 179.200-7.
     Nickel Plate, Sheet, and Strip.
    ASTM B 209-93 Standard Specification for      179.100-7; 179.200-7;
     Aluminum and Aluminum-Alloy Sheet and Plate.  179.220-7.
    ASTM B 221-76 Aluminum Alloy Extruded Bars,   178.46.
     Rods, Shapes, and Tubes.
    ASTM B 557-84 Tension Testing Wrought and     178.46.
     Cast Aluminum and Magnesium-Alloy Products.
    ASTM B 580-79 Standard Specification for      173.316; 173.318;
     Anodic Oxide Coatings on Aluminum, (Re-       178.338-17.
     approved 2000).
ASTM D 56-05, Standard Test Method for Flash      173.120
 Point by Tag Closed Cup Tester, approved May 1,
 2005.
ASTM D 86-07a, Standard Test Method for           173.121
 Distillation of Petroleum Products at
 Atmospheric Pressure, approved April 1, 2007.
ASTM D 93-08, Standard Test Methods for Flash     173.120
 Point by Pensky-Martens Closed Cup Tester,
 approved October 15, 2008.

[[Page 96]]

 
ASTM D 1078-05, Standard Test Method for          173.121
 Distillation Range of Volatile Organic Liquids,
 approved May 15, 2005.
    ASTM D 1238-90b Standard Test Method for      173.225.
     Flow Rates of Thermoplastics for Extrusion
     Plastometer.
    ASTM D 1709-01 Standard Text Methods for      173.197.
     Impact Resistance of Plastic Film by the
     Free-Falling Dart Method.
    ASTM D 1835-97 Standard Specification for     180.209.
     Liquefied Petroleum (LP) Gases.
    ASTM D 1838-64 Copper Strip Corrosion by      173.315.
     Liquefied Petroleum (LP) Gases.
    ASTM D 1922-00a Standard Test Method for      173.197.
     Propogation Tear Resistance of Plastic Film
     and Thin Sheeting by Pendulum Method.
ASTM D 3278-96 (Reapproved 2004) E \1\, Standard  173.120
 Test Methods for Flash Point of Liquids by
 Small Scale Closed-Cup Apparatus, approved
 November 1, 2004.
ASTM D 3828-07a, Standard Test Methods for Flash  173.120
 Point by Small Scale Closed Cup Tester,
 approved July 15, 2007.
    ASTM D 4206-96 Standard Test Method for       173.120.
     Sustained Burning of Liquid Mixtures Using
     the Small Scale Open-Cup Apparatus.
    ASTM D 4359-90 Standard Test Method for       171.8.
     Determining Whether a Material is a Liquid
     or a Solid.
    ASTM E 8-99 Standard Test Methods for         178.36; 178.37;
     Tension Testing of Metallic Materials.        178.38; 178.39;
                                                   178.44; 178.45;
                                                   178.50; 178.51;
                                                   178.53; 178.55;
                                                   178.56; 178.57;
                                                   178.58; 178.59;
                                                   178.60; 178.61;
                                                   178.68.
    ASTM E 23-98 Standard Test Methods for        178.57.
     Notched Bar Impact Testing of Metallic
     Materials.
    ASTM E 112-88 Standard Test Methods for       178.44.
     Determining Average Grain Size.
    ASTM E 112-96 Standard Test Methods for       178.274; Part 178,
     Determining Average Grain Size, 1996          appendix A.
     Edition.
    ASTM E 114-95 Standard Practice for           178.45.
     Ultrasonic Pulse-Echo Straight-Beam
     Examination by the Contact Method.
    ASTM E 213-98 Standard Practice for           178.45.
     Ultrasonic Examination of Metal Pipe and
     Tubing.
ASTM E 290-97a Standard Test Methods for Bend     178.37.
 Testing of Material for Ductility, published
 February 1998.
American Water Works Association, 1010 Vermont
 Avenue, N.W., Suite 810, Washington, DC 20005:
    AWWA Standard C207-55, Steel Pipe Flanges,    178.360-4.
     1955.
American Welding Society, 550 N.W. Le Jeune
 Road, Miami, Florida 33126:
    AWS Code B 3.0; Standard Qualification        178.356-2, 178.358-2.
     Procedure; 1972 (FRB 3.0-41, rev. May 1973).
    AWS Code D 1.0; Code for Welding in Building  178.356-2; 178.358-2.
     Construction (FR D 1.0-66, 1966).
Association of American Railroads, American
 Railroads Building, 50 F Street, NW.,
 Washington, DC 20001; telephone (877) 999-8824,
 http://www.aar.org/publications.com;

[[Page 97]]

 
    AAR Manual of Standards and Recommended       173.31; 174.63; 179.6;
     Practices, Section C--Part III,               179.7; 179.15;
     Specifications for Tank Cars, Specification   179.16; 179.20;
     M-1002, (AAR Specifications for Tank Cars),   179.22; 179.100-9;
     December 2000.                                179.100-10; 179.100-
                                                   12; 179.100-13;
                                                   179.100-14; 179.100-
                                                   18; 179.101-1;
                                                   179.102-1; 179.102-4;
                                                   179.102-17; 179.103-
                                                   5; 179.200-7; 179.200-
                                                   9; 179.200-10;
                                                   179.200-11; 179.200-
                                                   13; 179.200-17;
                                                   179.200-22; 179.201-
                                                   6; 179.220-6; 179.220-
                                                   7; 179.220-10;
                                                   179.220-11; 179.220-
                                                   14; 179.220-18;
                                                   179.220-26; 179.300-
                                                   9; 179.300-10;
                                                   179.300-15; 179.300-
                                                   17; 179.400-5;
                                                   179.400-6; 179.400-8;
                                                   179.400-11; 179.400-
                                                   12; 179.400-15;
                                                   179.400-18; 179.400-
                                                   20; 179.400-25;
                                                   180.509; 180.513;
                                                   180.515; 180.517.
    AAR Manual of Standards and Recommended       174.55; 174.63.
     Practices, Section I, Specially Equipped
     Freight Car and Intermodal Equipment, 1988.
    AAR Specifications for Design, Fabrication    179.16.
     and Construction of Freight Cars, Volume 1,
     1988.
Chlorine Institute, Inc., 1300 Wilson Boulevard,
 Arlington, VA 22209
    AAR Standard 286; AAR Manual of Standards     179.13
     and Recommended Practices, Section C, Car
     Construction Fundamentals and Details,
     Standard S-286, Free/Unrestricted
     Interchange for 286,000 lb Gross Rail Load
     Cars (Adopted 2002; Revised: 2003, 2005,
     2006).
    Chlorine Institute Emergency Kit ``A'' for    173.3
     100-lb. & 150 lb. Chlorine Cylinders (with
     the exception of repair method using Device
     8 for side leaks), Edition 10, June 2003.
    Chlorine Institute Emergency Kit ``B'' for    173.3
     Chlorine Ton Containers (with the exception
     of repair method using Device 9 for side
     leaks), Edition 9, June 2003.
    Type 1\1/2\ JQ 225, Dwg., H51970, Revision    173.315.
     F, November 1996; or Type 1\1/2\ JQ 225,
     Dwg. H50155, Revision H, November 1996.
    Section 3, Pamphlet 57, Emergency Shut-Off    177.840.
     Systems for Bulk Transfer of Chlorine,
     Edition 4, October 2003.
    Section 3, Pamphlet 166, Angle Valve          178.337-9.
     Guidelines for Chlorine Bulk
     Transportation, 1st Edition, October 2002.
    Standard Chlorine Angle Valve Assembly, Dwg.  178.337-9.
     104-8, July 1993.
    Excess Flow Valve with Removable Seat, Dwg.   178.337-8.
     101-7, July 1993.
    Excess Flow Valve with Removable Basket,      178.337-8.
     Dwg. 106-6, July 1993.
    Standards for Housing and Manway Covers for   178.337-10.
     Steel Cargo Tanks, Dwgs. 137-1 and 137-2,
     September 1, 1982.
    Typical Manway Arrangement Chlorine Cargo     178.337-10.
     Tank, Dwg 137-5, November 1996.
Canadian General Standards Board, Place du        171.12
 Portage III, 6B1 11.
Laurier Street, Gatineau, Quebec, Canada K1A 1G6
    National Standard of Canada (CAN/CGSB
     43.147--2005) Construction, Modification,
     Qualification, Maintenance, and Selection
     and Use of Means of Containment for the
     Handling, Offering for Transport, or
     Transportation of Dangerous Goods by Rail.

[[Page 98]]

 
    CGA Pamphlet C-3, Standards for Welding on    178.47; 178.50;
     Thin-Walled Steel Cylinders, 1994.            178.51; 178.53;
                                                   178.55; 178.56;
                                                   178.57; 178.58;
                                                   178.59; 178.60;
                                                   178.61; 178.65;
                                                   178.68; 180.211.
    CGA C-5, Cylinder Service Life--Seamless      173.302a.
     Steel High Pressure Cylinders, 1991
     (reaffirmed 1995).
    CGA Pamphlet C-6, Standards for Visual        173.3, 173.198,
     Inspection of Steel Compressed Gas            180.205, 180.209,
     Cylinders, 1993.                              180.211, 180.411,
                                                   180.519.
    CGA Pamphlet C-6.1, Standards for Visual      180.205; 180.209
     Inspection of High Pressure Aluminum
     Compressed Gas Cylinders, 2002, Fourth
     Edition.
    CGA Pamphlet C-6.2, Guidelines for Visual     180.205.
     Inspection and Requalification of Fiber
     Reinforced High Pressure Cylinders, 1996,
     Third Edition.
    CGA Pamphlet C-6.3, Guidelines for Visual     180.205; 180.209.
     Inspection and Requalification of Low
     Pressure Aluminum Compressed Gas Cylinders,
     1991.
    CGA C-7, Guide to Preparation of              172.400a.
     Precautionary Labeling and Marking of
     Compressed Gas Containers, Appendix A,
     issued 2004 (8th Edition).
    CGA Pamphlet C-8, Standard for                180.205; 180.209.
     Requalification of DOT-3HT Cylinder Design,
     1985.
    CGA Pamphlet C-11, Recommended Practices for  178.35.
     Inspection of Compressed Gas Cylinders at
     Time of Manufacture, 2001, Third Edition.
    CGA Pamphlet C-12, Qualification Procedure    173.301; 173.303;
     for Acetylene Cylinder Design, 1994.          178.59; 178.60.
    CGA Pamphlet C-13, Guidelines for Periodic    173.303; 180.205;
     Visual Inspection and Requalification of      180.209.
     Acetylene Cylinders, 2000, Fourth Edition.
    CGA Pamphlet C-14, Procedures for Fire        173.301; 173.323.
     Testing of DOT Cylinder Pressure Relief
     Device Systems, 1979.
    CGA Pamphlet G-2.2, Guideline Method for      173.315.
     Determining Minimum of 0.2% Water in
     Anhydrous Ammonia, 1985, Second Edition,
     Reaffirmed 1997.
    CGA Pamphlet G-4.1, Cleaning Equipment for    178.338-15.
     Oxygen Service, 1985.
CGA Pamphlet P-20, Standard for the               173.115.
 Classification of Toxic Gas Mixtures, 2003,
 Third Edition.
    CGA Pamphlet P-20, Standard for the           173.115.
     Classification of Toxic Gas Mixtures, 1995.
    CGA S-1.1, Pressure Relief Device Standards-- 173.301, 173.304a
     Part 1--Cylinders for Compressed Gases,       178.75.
     2005 (with the exception of paragraph
     9.1.1.1), Twelfth Edition.
    CGA Pamphlet S-1.2, Safety Relief Device      173.315; 173.318;
     Standards Part 2--Cargo and Portable Tanks    178.276; 178.277.
     for Compressed Gases, 1980.
    CGA S-7, Method for Selecting Pressure        173.301.
     Relief Devices for Compressed Gas Mixtures
     in Cylinders, 2005.
    CGA Technical Bulletin TB-2, Guidelines for   180.407; 180.413.
     Inspection and Repair of MC-330 and MC-331
     Cargo Tanks, 1980.
    CGA Technical Bulletin TB-25, Design          173.301.
     Considerations for Tube Trailers, 2008
     Edition.
Department of Defense (DOD), 2461 Eisenhower
 Avenue, Alexandria, VA 22331:
    DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1- 173.56.
     47; DLAR 8220.1: Explosives Hazard
     Classification Procedures, January 1998.
    Packaging of Hazardous Material, DLAD         173.7
     4145.41/ AR 700-143/AFJI 24-210/NAVSUPINST
     4030.55B/MCO 4030.40B, January 14, 2000.
Department of Energy (USDOE), 100 Independence
 Avenue SW., Washington, DC 20545:
    USDOE publications available from:
     Superintendent of Documents, Government
     Printing Office (GPO) or The National
     Technical Information Service (NTIS).
    USDOE, CAPE-1662, Revision 1, and Supplement  178.356-1; 178.356-2;
     1, Civilian Application Program Engineering   178.358-1; 178.358-2;
     Drawings, April 6, 1988.                      178.358-3; 178.358-4.
    USDOE, Material and Equipment Specification   178.356-2; 178.358-2.
     No. SP-9, Rev. 1, and Supplement--Fire
     Resistant Phenolic Foam, March 28, 1968.
    USDOE, KSS-471, November 30, 1986--Proposal   178.358-1; 178.358-3.
     for Modifications to U.S. Department of
     Transportation Specification 21PF-1, Fire
     and Shock Resistant Phenolic Foam--
     Insulated Metal Overpack.
General Services Administration, Specification
 Office, Room 6662, 7th and D Street, S.W.,
 Washington, DC 20407:
    Federal Specification RR-C-901D, Cylinders,   173.302; 173.336;
     Compressed Gas: Seamless Shatterproof, High   173.337.
     Pressure DOT 3AA Steel, and 3AL Aluminum,
     February 21, 2003 (Superseding RR-C-901C,
     1981).
Institute of Makers of Explosives, 1120 19th
 Street NW., Suite 310, Washington, DC 20036-
 3605:
IME Safety Library Publication No. 22 (IME        173.63; 177.835.
 Standard 22), Recommendations for the Safe
 Transportation of Detonators in a Vehicle with
 Certain Other Explosive Materials, February
 2007.
International Atomic Energy Agency (IAEA), P.O.
 Box 100, Wagramer Strasse 5, A-1400 Vienna,
 Austria:

[[Page 99]]

 
    Also available from: Bernan Associates, 4611-
     F Assembly Drive, Lanham, MD 20706-4391,
     USA; or Renouf Publishing Company, Ltd.,
     812 Proctor Avenue, Ogdensburg, New York
     13669, USA.
    IAEA, Regulations for the Safe Transport of   171.22; 171.23;
     Radioactive Material, (IAEA Regulations),     171.26, 173.415,
     1996 Edition (Revised), No. TS-R-1 (ST-1,     173.416, 173.417,
     Revised).                                     173.473
International Civil Aviation Organization
 (``ICAO''), 999 University Street,
 Montr[eacute]al, Quebec H3C 5H7, Canada, 1-514-
 954-8219, http://www.icao.int:
    ICAO Technical Instructions available from:
     INTEREG, International Regulations,
     Publishing and Distribution Organization,
     P.O. Box 60105, Chicago, IL 60660.
Technical Instructions for the Safe Transport of  171.8; 171.22; 171.23;
 Dangerous Goods by Air (ICAO Technical            171.24; 172.101;
 Instructions), 2011-2012 Edition.                 172.202; 172.401;
                                                   172.512; 172.519;
                                                   172.602; 172.704;
                                                   173.1; 173.56;
                                                   173.320; 175.33;
                                                   178.3.
International Electrotechnical Commission (IEC)
 3, rue de Varemb[eacute], P.O. Box 131, CH--
 1211, GENEVA 20, Switzerland:
    Fuel cell technologies--Part 6-1: Micro fuel  Sec.  175.10.
     cell power systems--Safety, IEC/PAS 62282-6-
     1:2006(E), First Edition 2006-02, with
     Corrigendum 1, First Edition 2007-04.
International Maritime Organization (``IMO''), 4
 Albert Embankment, London, SE1 7SR, United
 Kingdom or New York Nautical Instrument &
 Service Corporation, 140 West Broadway, New
 York, NY 10013, +44 (0) 20 7735 7611, http://
 www.imo.org:
International Convention for the Safety of Life   176.63, 176.84
 at Sea, 1974, as amended (SOLAS), Chapter II-2,
 Construction--Fire protection, fire detection
 and fire extinction, Regulation 19, Carriage of
 dangerous goods, Consolidated Edition 2009.
International Maritime Dangerous Goods Code       171.22; 171.23;
 (IMDG Code), 2010 Edition, Incorporating          171.25; 172.101
 Amendment 35-10 (English Edition), Volumes 1      172.202; 172.203
 and 2.                                            172.401; 172.502;
                                                   172.519; 172.602;
                                                   172.704; 173.1;
                                                   173.21; 173.56;
                                                   173.320; 176.2;
                                                   176.5; 176.11;
                                                   176.27; 176.30;
                                                   176.83; 176.84;
                                                   176.140; 176.720;
                                                   178.3; 178.274.
International Organization for Standardization,
 Case Postale 56, CH-1211, Geneve 20,
 Switzerland, http://www.iso.org:
    Also available from: ANSI 25, West 43rd
     Street, New York, NY 10036, 1-212-642-4900,
     http://www.ansi.org.
    ISO 535-1991(E) Paper and board--             178.516; 178.707;
     Determination of water absorptiveness--Cobb   178.708.
     method.
    ISO 1496-1: 1990 (E)--Series 1 freight        173.411
     containers--Specification and testing, Part
     1: General cargo containers. Fifth Edition,
     (August 15, 1990).
    ISO 1496-3--Series 1 freight containers--     178.74; 178.75;
     Specification and testing--Part 3: Tank       178.274.
     containers for liquids, gases and
     pressurized dry bulk, Fourth edition, March
     1995, (E).
ISO 1516:2002(E), Determination of flash/no       173.120.
 flash--Closed cup equilibrium method, Third
 Edition, 2002-03-01.
ISO 1523:2002(E), Determination of flash point--  173.120.
 Closed cup equilibrium method, Third Edition,
 2002-03-01.
    ISO 2431-1984(E) Standard Cup Method........  173.121.
ISO 2592:2000(E), Determination of flash and      173.120.
 fire points--Cleveland open cup method, Second
 Edition, 2000-09-15.
ISO 2719:2002(E), Determination of flash point--  173.120.
 Pensky-Martens closed cup method, Third
 Edition, 2002-11-15.
    ISO 2919-1980(E) Sealed radioactive sources-- 173.469.
     Classification.
    ISO 3036-1975(E) Board--Determination of      178.708.
     puncture resistance.
ISO 3405:2000(E), Petroleum products--            173.121.
 Determination of distillation characteristics
 at atmospheric pressure, Third Edition, 2000-03-
 01.
    ISO 3574-1986(E) Cold-reduced carbon steel    178.503; Part 178,
     sheet of commercial and drawing qualities.    appendix C.
ISO 3679:2004(E), Determination of flash point--  173.120.
 Rapid equilibrium closed cup method, Third
 Edition, 2004-04-01.
ISO 3680:2004(E), Determination of flash/no       173.120.
 flash--Rapid equilibrium closed cup method,
 Fourth Edition, 2004-04-01.
    ISO 3807-2, Cylinders for acetylene--Basic    173.303; 178.71.
     requirements--Part 2: Cylinders with
     fusible plugs, First edition, March 2000,
     (E).

[[Page 100]]

 
ISO 3924:1999(E), Petroleum products--            173.121.
 Determination of boiling range distribution--
 Gas chromatography method, Second Edition, 1999-
 08-01.
    ISO 4126-1 Safety valves--Part 1: General     178.274.
     Requirements, December 15, 1991, First
     Edition.
ISO 4626:1980(E), Volatile organic liquids--      173.121.
 Determination of boiling range of organic
 solvents used as raw materials, First Edition,
 1980-03-01.
ISO 4706:2008(E), Gas cylinders--Refillable       178.71.
 welded steel cylinders--Test pressure 60 bar
 and below, First Edition, 2008-04-15, Corrected
 Version, 2008-07-01.
    ISO 6406, Gas cylinders--Seamless steel gas   180.207.
     cylinders--Periodic inspection and testing,
     Second edition, February 2005, (E).
    ISO 6892 Metallic materials--Tensile          178.274.
     testing, July 15, 1984, First Edition.
    ISO 7225, Gas cylinders--Precautionary        178.71.
     labels, Second Edition, July 2005, (E).
    ISO 7866, Gas cylinders--Refillable seamless  178.71.
     aluminum alloy gas cylinders--Design,
     construction and testing, First edition,
     June 1999, (E).
    ISO 8115 Cotton bales--Dimensions and         172.102.
     density, 1986 Edition.
    ISO 9809-1: Gas cylinders--Refillable         178.37; 178.71;
     seamless steel gas cylinders--Design,         178.75.
     construction and testing--Part 1: Quenched
     and tempered steel cylinders with tensile
     strength less than 1 100 MPa., First
     edition, June 1999, (E).
    ISO 9809-2: Gas cylinders--Refillable         178.71; 178.75.
     seamless steel gas cylinders--Design,
     construction and testing--Part 2: Quenched
     and tempered steel cylinders with tensile
     strength greater than or equal to 1 100
     MPa., First edition, June 2000, (E).
    ISO 9809-3: Gas cylinders--Refillable         178.71; 178.75.
     seamless steel gas cylinders--Design,
     construction and testing--Part 3:
     Normalized steel cylinders, First edition,
     December 2000, (E).
    ISO 9978:1992(E)--Radiation protection--      173.469.
     Sealed radioactive sources--Leakage test
     methods. First Edition, (February 15, 1992).
ISO 10156:1996, Gases and Gas Mixtures--          173.115.
 Determination of fire potential and oxidizing
 ability for the selection of cylinder valve
 outlets, Second edition, February 1996 (E).
ISO 10156-2:2005, Gas cylinders--Gases and gas    173.115.
 mixtures--Part 2: Determination of oxidizing
 ability of toxic and corrosive gases and gas
 mixtures, First edition, August 2005, (E).
ISO 10297:2006(E), Transportable gas cylinders--  173.301b; 178.71.
 Cylinder valves--Specification and type
 testing, Second Edition, 2006-01-15.
ISO 10461:2005(E), Gas cylinders--Seamless        180.207.
 aluminum-alloy gas cylinders--Periodic
 inspection and testing, Second Edition, 2005-02-
 15 and Amendment 1, 2006-07-15.
    ISO 10462, Gas cylinders--Transportable       180.207.
     cylinders for dissolved acetylene--Periodic
     inspection and maintenance, Second edition,
     February 2005, (E).
ISO 10692-2:2001(E), Gas cylinders--Gas cylinder  173.40.
 valve connections for use in the micro-
 electronics industry--Part 2: Specification and
 type testing for valve to cylinder connections,
 First Edition, 2001-08-01.
    ISO 11114-1, Transportable gas cylinders--    173.301b; 178.71.
     Compatibility of cylinder and valve
     materials with gas contents--Part 1:
     Metallic materials, First edition, October
     1997, (E).
    ISO 11114-2, Transportable gas cylinders--    173.301b; 178.71.
     Compatibility of cylinder and valve
     materials with gas contents--Part 2: Non-
     metallic materials, First edition, December
     2000, (E).
    ISO 11117, Gas cylinders--Valve protection    173.301b.
     caps and valve guards for industrial and
     medical gas cylinders--Design, construction
     and tests, First edition, August 1998, (E).
    ISO 11118, Gas cylinders--Non-refillable      178.71.
     metallic gas cylinders--Specification and
     test methods, First edition, October 1999,
     (E).
    ISO 11119-1, Gas cylinders--Gas cylinders of  178.71.
     composite construction--Specification and
     test methods--Part 1: Hoop-wrapped
     composite gas cylinders, First edition, May
     2002, (E).
    ISO 11119-2, Gas cylinders--Gas cylinders of  178.71.
     composite construction--Specification and
     test methods--Part 2: Fully wrapped fibre
     reinforced composite gas cylinders with
     load-sharing metal liners, First edition,
     May 2002, (E).
    ISO 11119-3, Gas cylinders of composite       178.71.
     construction--Specification and test
     methods--Part 3: Fully wrapped fibre
     reinforced composite gas cylinders with non-
     load-sharing metallic or non-metallic
     liners, First edition, September 2002, (E).
    ISO 11120, Gas cylinders--Refillable          178.71; 178.75.
     seamless steel tubes of water capacity
     between 150 L and 3000 L--Design,
     construction and testing, First edition,
     March 1999, (E).
    ISO 11621, Gas cylinders--Procedures for      173.302, 173.336,
     change of gas service, First edition, April   173.337.
     1997, (E).
    ISO 11623, Transportable gas cylinders--      180.207.
     Periodic inspection and testing of
     composite gas cylinders, First edition,
     March 2002, (E).
ISO 13736:2008(E), Determination of flash point-- 173.120.
 Abel closed-cup method, Second Edition, 2008-09-
 15.
ISO 16111:2008(E), Transportable gas storage      173.301b; 173.311;
 devices--Hydrogen absorbed in reversible metal    178.71.
 hydride, First Edition, 2008-11-15.
ISO 18172-1:2007(E), Gas cylinders--Refillable    178.71.
 welded stainless steel cylinders--Part 1: Test
 pressure 6 MPa and below, First Edition, 2007-
 03-01.
ISO 20703:2006(E), Gas cylinders--Refillable      178.71.
 welded aluminum-alloy cylinders--Design,
 construction and testing, First Edition, 2006-
 05-01.
National Board of Boiler and Pressure Vessel
 Inspectors, 1055 Crupper Avenue, Columbus, Ohio
 43229:
    National Board Inspection Code, A Manual for  180.413.
     Boiler and Pressure Vessel Inspectors, NB-
     23, 1992 Edition.
National Fire Protection Association, 1
 Batterymarch Park, Quincy, MA, 02169-7471 1-617-
 770-3000,, http://www.nfpa.org:.
    NFPA 58-Liquefied Petroleum Gas Code, 2001    173.5, 173.315.
     Edition.
NFPA 498-Standard for Safe Havens and             177.835
 Interchange Lots for Vehicles Transporting
 Explosives, 2010 Edition.

[[Page 101]]

 
National Institute of Standards and Technology,
 Department of Commerce, 5285 Port Royal Road,
 Springfield, VA 22151:
    USDC, NBS Handbook H-28 (1957), 1957          179.2; 178.45; 178.46.
     Handbook of Screw-Thread Standards for
     Federal Services, December 1966 Edition.
Organization for Economic Cooperation and
 Development (OECD), OECD Publications and
 Information Center, 2001 L Street, N.W., Suite
 700, Washington, DC 20036:
OECD (2002), Test No. 404: Acute Dermal           173.137.
 Irritation/Corrosion, OECD Guidelines for the
 Testing of Chemicals, Section 4: Health
 Effects, OECD Publishing, adopted April 24,
 2002.
OECD (2004), Test No. 430: In Vitro Skin          173.137.
 Corrosion: Transcutaneous Electrical Resistance
 Test (TER), OECD Guidelines for the Testing of
 Chemicals, Section 4: Health Effects, OECD
 Publishing, adopted April 13, 2004.
OECD (2004), Test No. 431: In Vitro Skin          173.137.
 Corrosion: Human Skin Model Test, OECD
 Guidelines for the Testing of Chemicals,
 Section 4: Health Effects, OECD Publishing,
 adopted April 13, 2004.
OECD (2006), Test No. 435: In Vitro Membrane      173.137.
 Barrier Test Method for Skin Corrosion, OECD
 Guidelines for the Testing of Chemicals,
 Section 4: Health Effects, OECD Publishing,
 adopted July 19, 2006.
Transport Canada, TDG Canadian Government
 Publishing Center, Supply and Services, Canada,
 Ottawa, Ontario, Canada K1A 059, 416-973-1868,
 http://www.tc.gc.ca:
Transportation of Dangerous Goods Regulations     171.12; 171.22;
 (Transport Canada TDG Regulations), August 2001   171.23; 172.401;
 including Clear Language Amendments SOR 2001-     172.502; 172.519;
 286; SOR/2002-306 August 8, 2002; SOR/2003-273    172.602; 173.31;
 July 24, 2003; SOR/2003-400 December 3, 2003;     173.32; 173.33.
 SOR/2005-216 July 13, 2005; SOR/2005-279
 September 21, 2005; SOR/2008-34 February 7,
 2008 and SOR/2007-179 July 31, 2007.
Truck Trailer Manufacturers Association, 1020
 Princess Street, Alexandria, Virginia 22314:
    TTMA RP No. 61-98, Performance of manhole     180.405.
     and/or Fill Opening Assemblies on MC 306,
     DOT 406, Non-ASME MC 312 and Non-ASME DOT
     412 Cargo Tanks, June 1, 1998.
    TTMA RP No. 81-97, Performance of Spring      178.345-10; 178.346-3.
     Loaded Pressure Relief Valves on MC 306, MC
     307, MC 312, DOT 406, DOT 407, and DOT 412
     Tanks, July 1, 1997 Edition.
    TTMA TB No. 107, Procedure for Testing In-    180.405.
     Service Unmarked and/or Uncertified MC 306
     and Non-ASME MC 312 Type Cargo Tank Manhole
     Covers, June 1, 1998 Edition.
United Nations, Publications, 2 United Nations
 Plaza, Room DC2-853, New York, NY 10017, 1-212-
 963-8302, http://unp.un.org.
UN Recommendations on the Transport of Dangerous  171.8; 171.12;
 Goods, Model Regulations, sixteenth revised       172.202; 172.401;
 edition, Volumes I and II (2009).                 172.407; 172.502;
                                                   173.1; 173.3; 173.22;
                                                   173.24; 173.24b;
                                                   173.40; 173.56;
                                                   173.192; 173.302b;
                                                   173.304b; 178.75;
                                                   178.274; 178.500;
                                                   178.700; 178.900.
UN Recommendations on the Transport of Dangerous  172.102; 173.21;
 Goods, Manual of Tests and Criteria, fifth        173.56; 173.57;
 revised edition (2009).                           173.58; 173.60;
                                                   173.115; 173.124;
                                                   173.125; 173.127;
                                                   173.128; 173.137;
                                                   173.185; 173.220;
                                                   Part 173, appendix H;
                                                   178.274.
United States Enrichment Corporation, Inc.
 (USEC):
    USEC Inc., 6903 Rockledge Drive, Bethesda,
     MD 20817.
    USEC-651--Good Handling Practices for         173.417
     Uranium Hexafluoride, Revision 8, January
     1999.
------------------------------------------------------------------------

    (b) List of informational materials not requiring incorporation by 
reference. The materials listed in this paragraph do not require 
approval for incorporation by reference and are included for 
informational purposes. These materials may be used as noted in those 
sections in which the material is referenced.

------------------------------------------------------------------------
           Source and name of material               49 CFR reference
------------------------------------------------------------------------
American Biological Safety Association
  1202 Allanson Road, Mundelein, IL 60060
Risk Group Classification for Infectious Agents,  173.134
 1998.
American Institute of Chemical Engineers
 (AIChE),
  3 Park Avenue New York, NY 10016-5991
Process Safety Progress Journal, Vol. 21, No. 2.
Example of a Test Method for Venting Sizing:      Note to Sec.  173.
 OPPSD/SPI Methodology.                            225(h)(3)(vi).

[[Page 102]]

 
American Society for Testing and Materials, 100
 Barr Harbor Drive, West Conshohocken, PA 19428:
  Noncurrent ASTM Standards are available from:
   Engineering Societies Library, 354 East 47th
   Street, New York, NY 10017
ASTM E 380-89 Standards for Metric Practice.....  171.10
Association of American Railroads,
  American Railroads Building, 50 F Street, NW.,
   Washington, DC 20001
AAR Catalog Nos. SE60CHT; SE60CC; SE60CHTE;       179.14
 SE60CE; SE60DC; SE60DE.
AAR Catalog Nos. SE67CC; SE67CE; SE67BHT;         179.14
 SE67BC; SE67BHTE; SE67BE.
AAR Catalog Nos. SE68BHT; SE68BC; SE68BHTE;       179.14
 SE68BE.
AAR Catalog Nos. SE69AHTE; SE69AE...............  179.14
AAR Catalog Nos. SF70CHT; SF70CC; SF70CHTE;       179.14
 SF70CE.
AAR Catalog Nos. SF73AC; SF73AE; SF73AHT;         179.14
 SF73AHTE.
AAR Catalog Nos. SF79CHT; SF79CC; SF79CHTE;       179.14
 SF79CE.
Bureau of Explosives,
  Hazardous Materials Systems (BOE), Association
   of American Railroads, American Railroads
   Building, 50 F Street, NW., Washington, DC
   20001
Fetterley's Formula (The Determination of the     173.315
 Relief Dimensions for Safety Valves on
 Containers in which Liquefied gas is charged
 and when the exterior surface of the container
 is exposed to a temperature of 1,200 [deg]F.).
Intermodal Loading Guide for Products in Closed   174.55; 174.101;
 Trailers and Containers, issued June 2001.        174.112; 174.115.
Pamphlet 6, Illustrating Methods for Loading and  174.55; 174.101;
 Bracing Carload and Less-Than-Carload Shipments   174.112; 174.115;
 of Explosives and Other Dangerous Articles,       174.290
 1962.
Pamphlet 6A (includes appendix No. 1, October     174.101; 174.290
 1944 and appendix 2, December 1945),
 Illustrating Methods for Loading and Bracing
 Carload and Less-Than-Carload Shipments of
 Loaded Projectiles, Loaded Bombs, etc., 1943.
Pamphlet 6C, Illustrating Methods for Loading     174.55; 174.63;
 and Bracing Trailers and Less-Than-Trailer        174.101; 174.112;
 Shipments of Explosives and Other Dangerous       174.115
 Articles Via Trailer-on-Flatcar (TOFC) or
 Container-on-Flatcar (COFC), 1985.
Emergency Handling of Hazardous Materials in      171.7
 Surface Transportation, 1989.
Centers for Disease Control and Prevention
  1600 Clifton Road, Atlanta, GA 30333
Biosafety in Microbiological and Biomedical       173.134
 Laboratories, Fourth Edition, April 1999.
Compressed Gas Association, Inc., 4221 Walney
 Road, 5th Floor, Chantilly, Virginia 20151
CGA C-1.1, Personnel Training and Certification   180.209
 Guidelines for Cylinder Requalification By the
 Volumetric Expansion Method, 2004, First
 Edition.
National Institutes of Health
  Bethesda, MD 20892
NIH Guidelines for Research Involving             173.134
 Recombinant DNA Molecules (NIH Guidelines),
 January 2001, Appendix B.
Pantone Incorporated
  590 Commerce Boulevard, Carlstadt, New Jersey
   07072-3098
Pantone [reg] Formula guide coated/uncoated,      172.407, 172.519
 Second Edition 2004.
Society of Plastics Industries, Inc.,
  Organic Peroxide Producers Safety Division,
   1275 K Street, NW., Suite 400, Washington, DC
   20005
Self Accelerating Decomposition Temperature       173.21
 Test, 1972.
Truck Trailer Manufacturers Association,
  1020 Princess Street, Alexandria, Virginia
   22314, telephone (703) 549-3010, http://
   www.ttmanet.org:
TTMA RP No. 96-01, TTMA RP No. 96-01, Structural  178.345-3
 Integrity of DOT 406, DOT 407, and DOT 412
 Cylindrical Cargo Tanks, January 2001 Edition.
------------------------------------------------------------------------


[Amdt. 171-111, 55 FR 52466, Dec. 21, 1990]

    Editorial Note: For Federal Register citations affecting Sec. 
171.7, see the List of CFR Sections Affected which appears in the 
Finding Aids section of the printed volume and at www.fdsys.gov

    Editorial Note: At 68 FR 19273, Apr. 18, 2003, Sec. 171.7(a)(3) was 
amended by removing the entry for ``TTMA TB No. 81'' under ``Truck 
Trailer Manufacturers Association''. The amendment could not be 
incorporated because that entry does not exist.



Sec. 171.8  Definitions and abbreviations.

    In this subchapter,
    Administrator means the Administrator, Pipeline and Hazardous 
Materials Safety Administration.
    Aerosol means any non-refillable receptacle containing a gas 
compressed, liquefied or dissolved under pressure, the sole purpose of 
which is to expel a nonpoisonous (other than a Division 6.1 Packing 
Group III material) liquid, paste, or powder and fitted with a self-

[[Page 103]]

closing release device allowing the contents to be ejected by the gas.
    Aggregate lithium content means the sum of the grams of lithium 
content or equivalent lithium content contained by the cells comprising 
a battery.
    Agricultural product means a hazardous material, other than a 
hazardous waste, whose end use directly supports the production of an 
agricultural commodity including, but not limited to a fertilizer, 
pesticide, soil amendment or fuel. An agricultural product is limited to 
a material in Class 3, 8 or 9, Division 2.1, 2.2, 5.1, or 6.1, or an 
ORM-D material.
    Approval means a written authorization, including a competent 
authority approval, from the Associate Administrator or other designated 
Department official, to perform a function for which prior authorization 
by the Associate Administrator is required under subchapter C of this 
chapter (49 CFR parts 171 through 180.)
    Approved means approval issued or recognized by the Department 
unless otherwise specifically indicated in this subchapter.
    Asphyxiant gas means a gas which dilutes or replaces oxygen normally 
in the atmosphere.
    Associate Administrator means the Associate Administrator for 
Hazardous Materials Safety, Pipeline and Hazardous Materials Safety 
Administration.
    Atmospheric gases means air, nitrogen, oxygen, argon, krypton, neon 
and xenon.
    Authorized Inspection Agency means: (1) A jurisdiction which has 
adopted and administers one or more sections of the ASME Boiler and 
Pressure Vessel Code as a legal requirement and has a representative 
serving as a member of the ASME Conference Committee; or (2) an 
insurance company which has been licensed or registered by the 
appropriate authority of a State of the United States or a Province of 
Canada to underwrite boiler and pressure vessel insurance in such State 
or Province.
    Authorized Inspector means an Inspector who is currently 
commissioned by the National Board of Boiler and Pressure Vessel 
Inspectors and employed as an Inspector by an Authorized Inspection 
Agency.
    Bag means a flexible packaging made of paper, plastic film, 
textiles, woven material or other similar materials.
    Bar means 1 BAR = 100 kPa (14.5 psi).
    Barge means a non-selfpropelled vessel.
    Biological product. See Sec. 173.134 of this subchapter.
    Biological substances, Category B. See Sec. 173.134 of this 
subchapter.
    Bottle means an inner packaging having a neck of relatively smaller 
cross section than the body and an opening capable of holding a closure 
for retention of the contents.
    Bottom shell means that portion of a tank car tank surface, 
excluding the head ends of the tank car tank, that lies within two feet, 
measured circumferentially, of the bottom longitudinal center line of 
the tank car tank.
    Box means a packaging with complete rectangular or polygonal faces, 
made of metal, wood, plywood, reconstituted wood, fiberboard, plastic, 
or other suitable material. Holes appropriate to the size and use of the 
packaging, for purposes such as ease of handling or opening, or to meet 
classification requirements, are permitted as long as they do not 
compromise the integrity of the packaging during transportation, and are 
not otherwise prohibited in this subchapter.
    Break-bulk means packages of hazardous materials that are handled 
individually, palletized, or unitized for purposes of transportation as 
opposed to bulk and containerized freight.
    Btu means British thermal unit.
    Bulk packaging means a packaging, other than a vessel or a barge, 
including a transport vehicle or freight container, in which hazardous 
materials are loaded with no intermediate form of containment. A Large 
Packaging in which hazardous materials are loaded with an intermediate 
form of containment, such as one or more articles or inner packagings, 
is also a bulk packaging. Additionally, a bulk packaging has: * * *
    (1) A maximum capacity greater than 450 L (119 gallons) as a 
receptacle for a liquid;

[[Page 104]]

    (2) A maximum net mass greater than 400 kg (882 pounds) and a 
maximum capacity greater than 450 L (119 gallons) as a receptacle for a 
solid; or
    (3) A water capacity greater than 454 kg (1000 pounds) as a 
receptacle for a gas as defined in Sec. 173.115 of this subchapter.
    Bundle of cylinders means assemblies of UN cylinders fastened 
together and interconnected by a manifold and transported as a unit. The 
total water capacity for the bundle may not exceed 3,000 L, except that 
a bundle intended for the transport of gases in Division 2.3 is limited 
to a water capacity of 1,000 L.
    Bureau of Explosives means the Bureau of Explosives (B of E) of the 
Association of American Railroads.
    C means Celsius or Centigrade.
    Captain of the Port (COTP) means the officer of the Coast Guard, 
under the command of a District Commander, so designated by the 
Commandant for the purpose of giving immediate direction to Coast Guard 
law enforcement activities within an assigned area. As used in this 
subchapter, the term Captain of the Port includes an authorized 
representative of the Captain of the Port.
    Carfloat means a vessel that operates on a short run on an irregular 
basis and serves one or more points in a port area as an extension of a 
rail line or highway over water, and does not operate in ocean, 
coastwise, or ferry service.
    Cargo aircraft only means an aircraft that is used to transport 
cargo and is not engaged in carrying passengers. For purposes of this 
subchapter, the terms cargo aircraft only, cargo-only aircraft and cargo 
aircraft have the same meaning.
    Cargo tank means a bulk packaging that:
    (1) Is a tank intended primarily for the carriage of liquids or 
gases and includes appurtenances, reinforcements, fittings, and closures 
(for the definition of a tank, see 49 CFR 178.320, 178.337-1, or 
178.338-1, as applicable);
    (2) Is permanently attached to or forms a part of a motor vehicle, 
or is not permanently attached to a motor vehicle but which, by reason 
of its size, construction or attachment to a motor vehicle is loaded or 
unloaded without being removed from the motor vehicle; and
    (3) Is not fabricated under a specification for cylinders, 
intermediate bulk containers, multi-unit tank car tanks, portable tanks, 
or tank cars.
    Cargo tank motor vehicle means a motor vehicle with one or more 
cargo tanks permanently attached to or forming an integral part of the 
motor vehicle.
    Cargo vessel means: (1) Any vessel other than a passenger vessel; 
and
    (2) Any ferry being operated under authority of a change of 
character certificate issued by a Coast Guard Officer-in-Charge, Marine 
Inspection.
    Carrier means a person who transports passengers or property in 
commerce by rail car, aircraft, motor vehicle, or vessel.
    CC means closed-cup.
    Character of vessel means the type of service in which the vessel is 
engaged at the time of carriage of a hazardous material.
    Class means hazard class. See hazard class.
    Class 1. See Sec. 173.50 of this subchapter.
    Class 2. See Sec. 173.115 of this subchapter.
    Class 3. See Sec. 173.120 of this subchapter.
    Class 4. See Sec. 173.124 of this subchapter.
    Class 5. See Sec. 173.128 of this subchapter.
    Class 6. See Sec. 173.132 of this subchapter.
    Class 7. See Sec. 173.403 of this subchapter.
    Class 8. See Sec. 173.136 of this subchapter.
    Class 9. See Sec. 173.140 of this subchapter.
    Closure means a device which closes an opening in a receptacle.
    COFC means container-on-flat-car.
    Combination packaging means a combination of packaging, for 
transport purposes, consisting of one or more inner packagings secured 
in a non-bulk outer packaging. It does not include a composite 
packaging.
    Combustible liquid. See Sec. 173.120 of this subchapter.
    Commerce means trade or transportation in the jurisdiction of the 
United States within a single state; between a

[[Page 105]]

place in a state and a place outside of the state; that affects trade or 
transportation between a place in a state and place outside of the 
state; or on a United States-registered aircraft.
    Compatibility group letter means a designated alphabetical letter 
used to categorize different types of explosive substances and articles 
for purposes of stowage and segregation. See Sec. 173.52 of this 
subchapter.
    Competent Authority means a national agency responsible under its 
national law for the control or regulation of a particular aspect of the 
transportation of hazardous materials (dangerous goods). The term 
Appropriate Authority, as used in the ICAO Technical Instructions (IBR, 
see Sec. 171.7), has the same meaning as Competent Authority. For 
purposes of this subchapter, the Associate Administrator is the 
Competent Authority for the United States.
    Composite packaging means a packaging consisting of an outer 
packaging and an inner receptacle, so constructed that the inner 
receptacle and the outer packaging form an integral packaging. Once 
assembled it remains thereafter an integrated single unit; it is filled, 
stored, shipped and emptied as such.
    Compressed gas. See Sec. 173.115 of this subchapter.
    Consignee means the person or place shown on a shipping document, 
package marking, or other media as the location to which a carrier is 
directed to transport a hazardous material.
    Consumer commodity means a material that is packaged and distributed 
in a form intended or suitable for sale through retail sales agencies or 
instrumentalities for consumption by individuals for purposes of 
personal care or household use. This term also includes drugs and 
medicines.
    Containership means a cargo vessel designed and constructed to 
transport, within specifically designed cells, portable tanks and 
freight containers which are lifted on and off with their contents 
intact.
    Corrosive material. See Sec. 173.136 of this subchapter.
    Crate means an outer packaging with incomplete surfaces.
    Crewmember means a person assigned to perform duty in an aircraft 
during flight time.
    Cryogenic liquid. See Sec. 173.115(g) of this subchapter.
    Cultures and stocks. See Sec. 173.134 of this subchapter.
    Cylinder means a pressure vessel designed for pressures higher than 
40 psia and having a circular cross section. It does not include a 
portable tank, multi-unit tank car tank, cargo tank, or tank car.
    Dangerous when wet material. See Sec. 173.124 of this subchapter.
    Design Certifying Engineer means a person registered with the 
Department in accordance with subpart F of part 107 of this chapter who 
has the knowledge and ability to perform stress analysis of pressure 
vessels and otherwise determine whether a cargo tank design and 
construction meets the applicable DOT specification. A Design Certifying 
Engineer meets the knowledge and ability requirements of this section by 
meeting any one of the following requirements:
    (1) Has an engineering degree and one year of work experience in 
cargo tank structural or mechanical design;
    (2) Is currently registered as a professional engineer by 
appropriate authority of a state of the United States or a province of 
Canada; or
    (3) Has at least three years' experience in performing the duties of 
a Design Certifying Engineer prior to September 1, 1991.
    Designated facility means a hazardous waste treatment, storage, or 
disposal facility that has been designated on the manifest by the 
generator.
    District Commander means the District Commander of the Coast Guard, 
or his authorized representative, who has jurisdiction in the particular 
geographical area.
    Division means a subdivision of a hazard class.
    DOD means the U.S. Department of Defense.
    Domestic transportation means transportation between places within 
the United States other than through a foreign country.
    DOT or Department means U.S. Department of Transportation.
    Drum means a flat-ended or convex-ended cylindrical packaging made 
of metal, fiberboard, plastic, plywood, or

[[Page 106]]

other suitable materials. This definition also includes packagings of 
other shapes made of metal or plastic (e.g., round taper-necked 
packagings or pail-shaped packagings) but does not include cylinders, 
jerricans, wooden barrels or bulk packagings.
    Elevated temperature material means a material which, when offered 
for transportation or transported in a bulk packaging:
    (1) Is in a liquid phase and at a temperature at or above 100 [deg]C 
(212 [deg]F);
    (2) Is in a liquid phase with a flash point at or above 38 [deg]C 
(100 [deg]F) that is intentionally heated and offered for transportation 
or transported at or above its flash point; or
    (3) Is in a solid phase and at a temperature at or above 240 [deg]C 
(464 [deg]F).
    Engine means a locomotive propelled by any form of energy and used 
by a railroad.
    EPA means U.S. Environmental Protection Agency.
    Equivalent lithium content means, for a lithium-ion cell, the 
product of the rated capacity, in ampere-hours, of a lithium-ion cell 
times 0.3, with the result expressed in grams. The equivalent lithium 
content of a battery equals the sum of the grams of equivalent lithium 
content contained in the component cells of the battery.
    Etiologic agent. See Sec. 173.134 of this subchapter.
    EX number means a number preceded by the prefix ``EX'', assigned by 
the Associate Administrator, to an item that has been evaluated under 
the provisions of Sec. 173.56 of this subchapter.
    Explosive. See Sec. 173.50 of this subchapter.
    F means degree Fahrenheit.
    Farmer means a person engaged in the production or raising of crops, 
poultry, or livestock.
    Federal hazardous material transportation law means 49 U.S.C. 5101 
et seq.
    Ferry vessel means a vessel which is limited in its use to the 
carriage of deck passengers or vehicles or both, operates on a short run 
on a frequent schedule between two points over the most direct water 
route, other than in ocean or coastwise service, and is offered as a 
public service of a type normally attributed to a bridge or tunnel.
    Filling density has the following meanings:
    (1) For compressed gases in cylinders, see Sec. 173.304a(a)(2) 
table note 1.
    (2) For compressed gases in tank cars, see Sec. 173.314(c) table 
note 1.
    (3) For compressed gases in cargo tanks and portable tanks, see 
Sec. 173.315(a) table note 1.
    (4) For cryogenic liquids in cylinders, except hydrogen, see Sec. 
173.316(c)(1).
    (5) For hydrogen, cryogenic liquid in cylinders, see Sec. 
173.316(c)(3) table note 1.
    (6) For cryogenic liquids in cargo tanks, see Sec. 173.318(f)(1).
    (7) For cryogenic liquids in tank cars, see Sec. 173.319(d)(1).
    Flammable gas. See Sec. 173.115 of this subchapter.
    Flammable liquid. See Sec. 173.120 of this subchapter.
    Flammable solid. See Sec. 173.124 of this subchapter.
    Flash point. See Sec. 173.120 of this subchapter.
    Freight container means a reusable container having a volume of 64 
cubic feet or more, designed and constructed to permit being lifted with 
its contents intact and intended primarily for containment of packages 
(in unit form) during transportation.
    Fuel cell means an electrochemical device that converts the energy 
of the chemical reaction between a fuel, such as hydrogen or hydrogen 
rich gases, alcohols, or hydrocarbons, and an oxidant, such as air or 
oxygen, to direct current (d.c.) power, heat, and other reaction 
products.
    Fuel cell cartridge or fuel cartridge means an article that stores 
fuel for discharge into the fuel cell through a valve(s) that controls 
the discharge of fuel into the fuel cell.
    Fuel cell system means a fuel cell with an installed fuel cell 
cartridge together with wiring, valves, and other attachments that 
connect the fuel cell or cartridge to the device it powers. The fuel 
cell or cartridge may be so constructed that it forms an integral part 
of the device or may be removed and connected manually to the device.

[[Page 107]]

    Fuel tank means a tank other than a cargo tank, used to transport 
flammable or combustible liquid, or compressed gas for the purpose of 
supplying fuel for propulsion of the transport vehicle to which it is 
attached, or for the operation of other equipment on the transport 
vehicle.
    Fumigated lading. See Sec. Sec. 172.302(g) and 173.9.
    Gas means a material which has a vapor pressure greater than 300 kPa 
(43.5 psia) at 50 [deg]C (122 [deg]F) or is completely gaseous at 20 
[deg]C (68 [deg]F) at a standard pressure of 101.3 kPa (14.7 psia).
    Gross weight or Gross mass means the weight of a packaging plus the 
weight of its contents.
    Hazard class means the category of hazard assigned to a hazardous 
material under the definitional criteria of part 173 of this subchapter 
and the provisions of the Sec. 172.101 table. A material may meet the 
defining criteria for more than one hazard class but is assigned to only 
one hazard class.
    Hazard zone means one of four levels of hazard (Hazard Zones A 
through D) assigned to gases, as specified in Sec. 173.116(a) of this 
subchapter, and one of two levels of hazards (Hazard Zones A and B) 
assigned to liquids that are poisonous by inhalation, as specified in 
Sec. 173.133(a) of this subchapter. A hazard zone is based on the LC50 
value for acute inhalation toxicity of gases and vapors, as specified in 
Sec. 173.133(a).
    Hazardous material means a substance or material that the Secretary 
of Transportation has determined is capable of posing an unreasonable 
risk to health, safety, and property when transported in commerce, and 
has designated as hazardous under section 5103 of Federal hazardous 
materials transportation law (49 U.S.C. 5103). The term includes 
hazardous substances, hazardous wastes, marine pollutants, elevated 
temperature materials, materials designated as hazardous in the 
Hazardous Materials Table (see 49 CFR 172.101), and materials that meet 
the defining criteria for hazard classes and divisions in part 173 of 
subchapter C of this chapter.
    Hazardous substance for the purposes of this subchapter, means a 
material, including its mixtures and solutions, that--
    (1) Is listed in the appendix A to Sec. 172.101 of this subchapter;
    (2) Is in a quantity, in one package, which equals or exceeds the 
reportable quantity (RQ) listed in the appendix A to Sec. 172.101 of 
this subchapter; and
    (3) When in a mixture or solution--
    (i) For radionuclides, conforms to paragraph 7 of the appendix A to 
Sec. 172.101.
    (ii) For other than radionuclides, is in a concentration by weight 
which equals or exceeds the concentration corresponding to the RQ of the 
material, as shown in the following table:

------------------------------------------------------------------------
                                                      Concentration by
                                                           weight
               RQ pounds (kilograms)               ---------------------
                                                     Percent      PPM
------------------------------------------------------------------------
5000 (2270).......................................         10    100,000
1000 (454)........................................          2     20,000
100 (45.4)........................................        0.2      2,000
10 (4.54).........................................       0.02        200
1 (0.454).........................................      0.002         20
------------------------------------------------------------------------

    The term does not include petroleum, including crude oil or any 
fraction thereof which is not otherwise specifically listed or 
designated as a hazardous substance in appendix A to Sec. 172.101 of 
this subchapter, and the term does not include natural gas, natural gas 
liquids, liquefied natural gas, or synthetic gas usable for fuel (or 
mixtures of natural gas and such synthetic gas).
    Hazardous waste, for the purposes of this chapter, means any 
material that is subject to the Hazardous Waste Manifest Requirements of 
the U.S. Environmental Protection Agency specified in 40 CFR part 262.
    Hazmat means a hazardous material.
    Hazmat employee means: (1) A person who is:
    (i) Employed on a full-time, part time, or temporary basis by a 
hazmat employer and who in the course of such full time, part time or 
temporary employment directly affects hazardous materials transportation 
safety;
    (ii) Self-employed (including an owner-operator of a motor vehicle, 
vessel, or aircraft) transporting hazardous materials in commerce who in 
the course of such self-employment directly affects hazardous materials 
transportation safety;

[[Page 108]]

    (iii) A railroad signalman; or
    (iv) A railroad maintenance-of-way employee.
    (2) This term includes an individual, employed on a full time, part 
time, or temporary basis by a hazmat employer, or who is self-employed, 
who during the course of employment:
    (i) Loads, unloads, or handles hazardous materials;
    (ii) Designs, manufactures, fabricates, inspects, marks, maintains, 
reconditions, repairs, or tests a package, container or packaging 
component that is represented, marked, certified, or sold as qualified 
for use in transporting hazardous material in commerce.
    (iii) Prepares hazardous materials for transportation;
    (iv) Is responsible for safety of transporting hazardous materials;
    (v) Operates a vehicle used to transport hazardous materials.
    Hazmat employer means:
    (1) A person who employs or uses at least one hazmat employee on a 
full-time, part time, or temporary basis; and who:
    (i) Transports hazardous materials in commerce;
    (ii) Causes hazardous materials to be transported in commerce; or
    (iii) Designs, manufactures, fabricates, inspects, marks, maintains, 
reconditions, repairs or tests a package, container, or packaging 
component that is represented, marked, certified, or sold by that person 
as qualified for use in transporting hazardous materials in commerce;
    (2) A person who is self-employed (including an owner-operator of a 
motor vehicle, vessel, or aircraft) transporting materials in commerce; 
and who:
    (i) Transports hazardous materials in commerce;
    (ii) Causes hazardous materials to be transported in commerce; or
    (iii) Designs, manufactures, fabricates, inspects, marks, maintains, 
reconditions, repairs or tests a package, container, or packaging 
component that is represented, marked, certified, or sold by that person 
as qualified for use in transporting hazardous materials in commerce; or
    (3) A department, agency, or instrumentality of the United States 
Government, or an authority of a State, political subdivision of a 
State, or an Indian tribe; and who:
    (i) Transports hazardous materials in commerce;
    (ii) Causes hazardous materials to be transported in commerce; or
    (iii) Designs, manufactures, fabricates, inspects, marks, maintains, 
reconditions, repairs or tests a package, container, or packaging 
component that is represented, marked, certified, or sold by that person 
as qualified for use in transporting hazardous materials in commerce.
    Hermetically sealed means closed by fusion, gasketing, crimping, or 
equivalent means so that no gas or vapor can enter or escape.
    Household waste means any solid waste (including garbage, trash, and 
sanitary waste from septic tanks) derived from households (including 
single and multiple residences, hotels and motels, bunkhouses, ranger 
stations, crew quarters, campgrounds, picnic grounds, and day-use 
recreation areas). This term is not applicable to consolidated shipments 
of household hazardous materials transported from collection centers. A 
collection center is a central location where household waste is 
collected.
    HMR means the Hazardous Materials Regulations, Parts 171 through 180 
of this chapter.
    IAEA means International Atomic Energy Agency.
    IATA means International Air Transport Association.
    ICAO means International Civil Aviation Organization.
    IMO means International Maritime Organization.
    Incorporated by reference or IBR means a publication or a portion of 
a publication that is made a part of the regulations of this subchapter. 
See Sec. 171.7.
    Infectious substance (etiologic agent). See Sec. 173.134 of this 
subchapter.
    Inner packaging means a packaging for which an outer packaging is 
required for transport. It does not include the inner receptacle of a 
composite packaging.

[[Page 109]]

    Inner receptacle means a receptacle which requires an outer 
packaging in order to perform its containment function. The inner 
receptacle may be an inner packaging of a combination packaging or the 
inner receptacle of a composite packaging.
    Intermediate bulk container or IBC means a rigid or flexible 
portable packaging, other than a cylinder or portable tank, which is 
designed for mechanical handling. Standards for IBCs manufactured in the 
United States are set forth in subparts N and O of part 178 of this 
subchapter.
    Intermediate packaging means a packaging which encloses an inner 
packaging or article and is itself enclosed in an outer packaging.
    Intermodal container means a freight container designed and 
constructed to permit it to be used interchangeably in two or more modes 
of transport.
    Intermodal portable tank or IM portable tank means a specific class 
of portable tanks designed primarily for international intermodal use.
    International transportation means transportation--
    (1) Between any place in the United States and any place in a 
foreign country;
    (2) Between places in the United States through a foreign country; 
or
    (3) Between places in one or more foreign countries through the 
United States.
    Irritating material. See Sec. 173.132(a)(2) of this subchapter.
    Jerrican means a metal or plastic packaging of rectangular or 
polygonal cross-section.
    Large packaging means a packaging that--
    (1) Consists of an outer packaging that contains articles or inner 
packagings;
    (2) Is designated for mechanical handling;
    (3) Exceeds 400 kg net mass or 450 liters (118.9 gallons) capacity;
    (4) Has a volume of not more than 3 cubic meters (m\3\) (see Sec. 
178.801(i) of this subchapter); and
    (5) Conforms to the requirements for the construction, testing and 
marking of Large Packagings as specified in subparts P and Q of part 178 
of this subchapter.
    Limited quantity, when specified as such in a section applicable to 
a particular material, means the maximum amount of a hazardous material 
for which there is a specific labeling or packaging exception.
    Lighter means a mechanically operated flame-producing device 
employing an ignition device and containing a Class 3 or a Division 2.1 
material. For design, capacity, and filling density requirements for 
lighters containing a Division 2.1 material, see Sec. 173.308.
    Lighter refill means a pressurized container that does not contain 
an ignition device but does contain a release device and is intended for 
use as a replacement cartridge in a lighter or to refill a lighter with 
a Division 2.1 flammable gas fuel. For capacity limits, see Sec. 
173.306(h) of this subchapter.
    Liquid means a material, other than an elevated temperature 
material, with a melting point or initial melting point of 20 [deg]C (68 
[deg]F) or lower at a standard pressure of 101.3 kPa (14.7 psia). A 
viscous material for which a specific melting point cannot be determined 
must be subjected to the procedures specified in ASTM D 4359 ``Standard 
Test Method for Determining Whether a Material is Liquid or Solid'' 
(IBR, see Sec. 171.7).
    Liquid phase means a material that meets the definition of liquid 
when evaluated at the higher of the temperature at which it is offered 
for transportation or at which it is transported, not at the 38 [deg]C 
(100 [deg]F) temperature specified in ASTM D 4359 (IBR, see Sec. 
171.7).
    Lithium content means the mass of lithium in the anode of a lithium 
metal or lithium alloy cell. The lithium content of a battery equals the 
sum of the grams of lithium content contained in the component cells of 
the battery. For a lithium-ion cell see the definition for ``equivalent 
lithium content''.
    Loading incidental to movement means loading by carrier personnel or 
in the presence of carrier personnel of packaged or containerized 
hazardous material onto a transport vehicle, aircraft, or vessel for the 
purpose of transporting it, including the loading, blocking and bracing 
a hazardous materials package in a freight container or transport 
vehicle, and segregating a

[[Page 110]]

hazardous materials package in a freight container or transport vehicle 
from incompatible cargo. For a bulk packaging, loading incidental to 
movement means filling the packaging with a hazardous material for the 
purpose of transporting it. Loading incidental to movement includes 
transloading.
    Magazine vessel means a vessel used for the receiving, storing, or 
dispensing of explosives.
    Magnetic material. See Sec. 173.21(d) of this subchapter.
    Marine pollutant, means a material which is listed in appendix B to 
Sec. 172.101 of this subchapter (also see Sec. 171.4) and, when in a 
solution or mixture of one or more marine pollutants, is packaged in a 
concentration which equals or exceeds:
    (1) Ten percent by weight of the solution or mixture for materials 
listed in the appendix; or
    (2) One percent by weight of the solution or mixture for materials 
that are identified as severe marine pollutants in the appendix.
    Marking means a descriptive name, identification number, 
instructions, cautions, weight, specification, or UN marks, or 
combinations thereof, required by this subchapter on outer packagings of 
hazardous materials.
    Material of trade means a hazardous material, other than a hazardous 
waste, that is carried on a motor vehicle--
    (1) For the purpose of protecting the health and safety of the motor 
vehicle operator or passengers;
    (2) For the purpose of supporting the operation or maintenance of a 
motor vehicle (including its auxiliary equipment); or
    (3) By a private motor carrier (including vehicles operated by a 
rail carrier) in direct support of a principal business that is other 
than transportation by motor vehicle.
    Material poisonous by inhalation or Material toxic by inhalation 
means:
    (1) A gas meeting the defining criteria in Sec. 173.115(c) of this 
subchapter and assigned to Hazard Zone A, B, C, or D in accordance with 
Sec. 173.116(a) of this subchapter;
    (2) A liquid (other than as a mist) meeting the defining criteria in 
Sec. 173.132(a)(1)(iii) of this subchapter and assigned to Hazard Zone 
A or B in accordance with Sec. 173.133(a) of this subchapter; or
    (3) Any material identified as an inhalation hazard by a special 
provision in column 7 of the Sec. 172.101 table.
    Maximum allowable working pressure or MAWP: For DOT specification 
cargo tanks used to transport liquid hazardous materials, see Sec. 
178.320(a) of this subchapter.
    Maximum capacity means the maximum inner volume of receptacles or 
packagings.
    Maximum net mass means the allowable maximum net mass of contents in 
a single packaging, or as used in subpart M of part 178 of this 
subchapter, the maximum combined mass of inner packaging, and the 
contents thereof.
    Mechanical displacement meter prover means a mechanical device used 
in the oilfield service industry consisting of a pipe assembly that is 
used to calibrate the accuracy and performance of meters that measure 
the quantities of a product being pumped or transferred at facilities 
such as drilling locations, refineries, tank farms, and loading racks.
    Metered delivery service means a cargo tank unloading operation 
conducted at a metered flow rate of 378.5 L (100 gallons) per minute or 
less through an attached delivery hose with a nominal inside diameter of 
3.175 cm (1\1/4\ inches) or less.
    Metal hydride storage system means a single complete hydrogen 
storage system that includes a receptacle, metal hydride, pressure 
relief device, shut-off valve, service equipment and internal components 
used for the transportation of hydrogen only.
    Miscellaneous hazardous material. See Sec. 173.140 of this 
subchapter.
    Mixture means a material composed of more than one chemical compound 
or element.
    Mode means any of the following transportation methods; rail, 
highway, air, or water.
    Motor vehicle includes a vehicle, machine, tractor, trailer, or 
semitrailer, or any combination thereof, propelled or drawn by 
mechanical power and used upon the highways in the transportation of 
passengers or property. It does not include a vehicle, locomotive, or 
car operated exclusively on a rail or

[[Page 111]]

rails, or a trolley bus operated by electric power derived from a fixed 
overhead wire, furnishing local passenger transportation similar to 
street-railway service.
    Movement means the physical transfer of a hazardous material from 
one geographic location to another by rail car, aircraft, motor vehicle, 
or vessel.
    Multiple-element gas container or MEGC means assemblies of UN 
cylinders, tubes, or bundles of cylinders interconnected by a manifold 
and assembled within a framework. The term includes all service 
equipment and structural equipment necessary for the transport of gases.
    Name of contents means the proper shipping name as specified in 
Sec. 172.101 of this subchapter.
    Navigable waters means, for the purposes of this subchapter, waters 
of the United States, including the territorial seas.
    Non-bulk packaging means a packaging which has:
    (1) A maximum capacity of 450 L (119 gallons) or less as a 
receptacle for a liquid;
    (2) A maximum net mass of 400 kg (882 pounds) or less and a maximum 
capacity of 450 L (119 gallons) or less as a receptacle for a solid; or
    (3) A water capacity of 454 kg (1000 pounds) or less as a receptacle 
for a gas as defined in Sec. 173.115 of this subchapter.
    Nonflammable gas. See Sec. 173.115 of this subchapter.
    N.O.S. means not otherwise specified.
    N.O.S. description means a shipping description from the Sec. 
172.101 table which includes the abbreviation n.o.s.
    NPT means an American Standard taper pipe thread conforming to the 
requirements of NBS Handbook H-28 (IBR, see Sec. 171.7).
    NRC (non-reusable container) means a packaging (container) whose 
reuse is restricted in accordance with the provisions of Sec. 173.28 of 
this subchapter.
    Occupied caboose means a rail car being used to transport non-
passenger personnel.
    Officer in Charge, Marine Inspection means a person from the 
civilian or military branch of the Coast Guard designated as such by the 
Commandant and who under the supervision and direction of the Coast 
Guard District Commander is in charge of a designated inspection zone 
for the performance of duties with respect to the enforcement and 
administration of title 52, Revised Statutes, acts amendatory thereof or 
supplemental thereto, rules and regulations thereunder, and the 
inspection required thereby.
    Offshore supply vessel means a cargo vessel of less than 500 gross 
tons that regularly transports goods, supplies or equipment in support 
of exploration or production of offshore mineral or energy resources.
    Open cryogenic receptacle means a transportable thermally insulated 
receptacle for refrigerated liquefied gases maintained at atmospheric 
pressure by continuous venting of the refrigerated gas.
    Operator means a person who controls the use of an aircraft, vessel, 
or vehicle.
    Organic peroxide. See Sec. 173.128 of this subchapter.
    ORM means other regulated material. See Sec. 173.144 of this 
subchapter.
    Outage or ullage means the amount by which a packaging falls short 
of being liquid full, usually expressed in percent by volume.
    Outer packaging means the outermost enclosure of a composite or 
combination packaging together with any absorbent materials, cushioning 
and any other components necessary to contain and protect inner 
receptacles or inner packagings.
    Overpack, except as provided in subpart K of part 178 of this 
subchapter, means an enclosure that is used by a single consignor to 
provide protection or convenience in handling of a package or to 
consolidate two or more packages. Overpack does not include a transport 
vehicle, freight container, or aircraft unit load device. Examples of 
overpacks are one or more packages:
    (1) Placed or stacked onto a load board such as a pallet and secured 
by strapping, shrink wrapping, stretch wrapping, or other suitable 
means; or
    (2) Placed in a protective outer packaging such as a box or crate.
    Oxidizer. See Sec. 173.127 of this subchapter.
    Oxidizing gas means a gas which may, generally by providing oxygen, 
cause

[[Page 112]]

or contribute to the combustion of other material more than air does.
    Oxidizing gas means a gas that may, generally by providing oxygen, 
cause or contribute to the combustion of other material more than air 
does. Specifically, this means a pure gas or gas mixture with an 
oxidizing power greater than 23.5% as determined by a method specified 
in ISO 10156: or 10156-2: (IBR, see Sec. 171.7 of this subchapter) (see 
also Sec. 173.115(k)).
    Oxygen generator (chemical) means a device containing chemicals that 
upon activation release oxygen as a product of chemical reaction.
    Package or Outside Package means a packaging plus its contents. For 
radioactive materials, see Sec. 173.403 of this subchapter.
    Packaging means a receptacle and any other components or materials 
necessary for the receptacle to perform its containment function in 
conformance with the minimum packing requirements of this subchapter. 
For radioactive materials packaging, see Sec. 173.403 of this 
subchapter.
    Packing group means a grouping according to the degree of danger 
presented by hazardous materials. Packing Group I indicates great 
danger; Packing Group II, medium danger; Packing Group III, minor 
danger. See Sec. 172.101(f) of this subchapter.
    Passenger (With respect to vessels and for the purposes of part 176 
only) means a person being carried on a vessel other than:
    (1) The owner or his representative;
    (2) The operator;
    (3) A bona fide member of the crew engaged in the business of the 
vessel who has contributed no consideration for his carriage and who is 
paid for his services; or
    (4) A guest who has not contributed any consideration directly or 
indirectly for his carriage.
    Passenger-carrying aircraft means an aircraft that carries any 
person other than a crewmember, company employee, an authorized 
representative of the United States, or a person accompanying the 
shipment.
    Passenger vessel means--
    (1) A vessel subject to any of the requirements of the International 
Convention for the Safety of Life at Sea, 1974, which carries more than 
12 passengers;
    (2) A cargo vessel documented under the laws of the United States 
and not subject to that Convention, which carries more than 16 
passengers;
    (3) A cargo vessel of any foreign nation that extends reciprocal 
privileges and is not subject to that Convention and which carries more 
than 16 passengers; and
    (4) A vessel engaged in a ferry operation and which carries 
passengers.
    Person means an individual, corporation, company, association, firm, 
partnership, society, joint stock company; or a government, Indian 
Tribe, or authority of a government or Tribe, that offers a hazardous 
material for transportation in commerce, transports a hazardous material 
to support a commercial enterprise, or designs, manufactures, 
fabricates, inspects, marks, maintains, reconditions, repairs, or tests 
a package, container, or packaging component that is represented, 
marked, certified, or sold as qualified for use in transporting 
hazardous material in commerce. This term does not include the United 
States Postal Service or, for purposes of 49 U.S.C. 5123 and 5124, a 
Department, agency, or instrumentality of the government.
    Person who offers or offeror means:
    (1) Any person who does either or both of the following:
    (i) Performs, or is responsible for performing, any pre-
transportation function required under this subchapter for 
transportation of the hazardous material in commerce.
    (ii) Tenders or makes the hazardous material available to a carrier 
for transportation in commerce.
    (2) A carrier is not an offeror when it performs a function required 
by this subchapter as a condition of acceptance of a hazardous material 
for transportation in commerce (e.g., reviewing shipping papers, 
examining packages to ensure that they are in conformance with this 
subchapter, or preparing shipping documentation for its own use) or when 
it transfers a hazardous material to another carrier for continued 
transportation in commerce without performing a pre-transportation 
function.

[[Page 113]]

    PHMSA means the Pipeline and Hazardous Materials Safety 
Administration, U.S. Department of Transportation, Washington, DC 20590.
    Placarded car means a rail car which is placarded in accordance with 
the requirements of part 172 of this subchapter.
    Poisonous gas. See Sec. 173.115 of this subchapter.
    Poisonous materials. See Sec. 173.132 of this subchapter.
    Portable tank means a bulk packaging (except a cylinder having a 
water capacity of 1000 pounds or less) designed primarily to be loaded 
onto, or on, or temporarily attached to a transport vehicle or ship and 
equipped with skids, mountings, or accessories to facilitate handling of 
the tank by mechanical means. It does not include a cargo tank, tank 
car, multi-unit tank car tank, or trailer carrying 3AX, 3AAX, or 3T 
cylinders.
    Preferred route or Preferred highway is a highway for shipment of 
highway route controlled quantities of radioactive materials so 
designated by a State routing agency, and any Interstate System highway 
for which an alternative highway has not been designated by such State 
agency as provided by Sec. 397.103 of this title.
    Pre-transportation function means a function specified in the HMR 
that is required to assure the safe transportation of a hazardous 
material in commerce, including--
    (1) Determining the hazard class of a hazardous material.
    (2) Selecting a hazardous materials packaging.
    (3) Filling a hazardous materials packaging, including a bulk 
packaging.
    (4) Securing a closure on a filled or partially filled hazardous 
materials package or container or on a package or container containing a 
residue of a hazardous material.
    (5) Marking a package to indicate that it contains a hazardous 
material.
    (6) Labeling a package to indicate that it contains a hazardous 
material.
    (7) Preparing a shipping paper.
    (8) Providing and maintaining emergency response information.
    (9) Reviewing a shipping paper to verify compliance with the HMR or 
international equivalents.
    (10) For each person importing a hazardous material into the United 
States, providing the shipper with timely and complete information as to 
the HMR requirements that will apply to the transportation of the 
material within the United States.
    (11) Certifying that a hazardous material is in proper condition for 
transportation in conformance with the requirements of the HMR.
    (12) Loading, blocking, and bracing a hazardous materials package in 
a freight container or transport vehicle.
    (13) Segregating a hazardous materials package in a freight 
container or transport vehicle from incompatible cargo.
    (14) Selecting, providing, or affixing placards for a freight 
container or transport vehicle to indicate that it contains a hazardous 
material.
    Primary hazard means the hazard class of a material as assigned in 
the Sec. 172.101 table.
    Private track or Private siding means: (i) Track located outside of 
a carrier's right-of-way, yard, or terminals where the carrier does not 
own the rails, ties, roadbed, or right-of-way, or
    (ii) Track leased by a railroad to a lessee, where the lease 
provides for, and actual practice entails, exclusive use of that 
trackage by the lessee and/or a general system railroad for purpose of 
moving only cars shipped to or by the lessee, and where the lessor 
otherwise exercises no control over or responsibility for the trackage 
or the cars on the trackage.
    Proper shipping name means the name of the hazardous material shown 
in Roman print (not italics) in Sec. 172.101 of this subchapter.
    Psi means pounds per square inch.
    Psia means pounds per square inch absolute.
    Psig means pounds per square inch gauge.
    Public vessel means a vessel owned by and being used in the public 
service of the United States. It does not include a vessel owned by the 
United States and engaged in a trade or commercial service or a vessel 
under contract or charter to the United States.
    Pyrophoric liquid. See Sec. 173.124(b) of this subchapter.

[[Page 114]]

    Radioactive materials. See Sec. 173.403 of this subchapter for 
definitions relating to radioactive materials.
    Rail car means a car designed to carry freight or non-passenger 
personnel by rail, and includes a box car, flat car, gondola car, hopper 
car, tank car, and occupied caboose.
    Railroad means a person engaged in transportation by rail.
    Receptacle means a containment vessel for receiving and holding 
materials, including any means of closing.
    U.N. Recommendations means the U.N. Recommendations on the Transport 
of Dangerous Goods, Model Regulations (IBR, see Sec. 171.7 of this 
subchapter).
    Reconditioned packaging. See Sec. 173.28 of this subchapter.
    Registered Inspector means a person registered with the Department 
in accordance with subpart F of part 107 of this chapter who has the 
knowledge and ability to determine whether a cargo tank conforms to the 
applicable DOT specification. A Registered Inspector meets the knowledge 
and ability requirements of this section by meeting any one of the 
following requirements:
    (1) Has an engineering degree and one year of work experience 
relating to the testing and inspection of cargo tanks;
    (2) Has an associate degree in engineering and two years of work 
experience relating to the testing and inspection of cargo tanks;
    (3) Has a high school diploma (or General Equivalency Diploma) and 
three years of work experience relating to the testing and inspection of 
cargo tanks; or
    (4) Has at least three years' experience performing the duties of a 
Registered Inspector prior to September 1, 1991.
    Regulated medical waste. See Sec. 173.134 of this subchapter.
    Remanufactured packagings. See Sec. 173.28 of this subchapter.
    Reportable quantity (RQ) for the purposes of this subchapter means 
the quantity specified in column 2 of the appendix to Sec. 172.101 for 
any material identified in column 1 of the appendix.
    Research means investigation or experimentation aimed at the 
discovery of new theories or laws and the discovery and interpretation 
of facts or revision of accepted theories or laws in the light of new 
facts. Research does not include the application of existing technology 
to industrial endeavors.
    Residue means the hazardous material remaining in a packaging, 
including a tank car, after its contents have been unloaded to the 
maximum extent practicable and before the packaging is either refilled 
or cleaned of hazardous material and purged to remove any hazardous 
vapors.
    Reused packaging. See Sec. 173.28 of this subchapter.
    SADT means self-accelerated decomposition temperature. See Sec. 
173.21(f) of this subchapter.
    Salvage packaging means a special packaging conforming to Sec. 
173.3 of this subchapter into which damaged, defective, leaking, or non-
conforming hazardous materials packages, or hazardous materials that 
have spilled or leaked, are placed for purposes of transport for 
recovery or disposal.
    SCF (standard cubic foot) means one cubic foot of gas measured at 60 
[deg]F. and 14.7 psia.
    Secretary means the Secretary of Transportation.
    Self-defense spray means an aerosol or non-pressurized device that:
    (1) Is intended to have an irritating or incapacitating effect on a 
person or animal; and
    (2) Meets no hazard criteria other than for Class 9 (for example, a 
pepper spray; see Sec. 173.140(a) of this subchapter) and, for an 
aerosol, Division 2.1 or 2.2 (see Sec. 173.115 of this subchapter), 
except that it may contain not more than two percent by mass of a tear 
gas substance (e.g., chloroacetophenone (CN) or 0-
chlorobenzylmalonitrile (CS); see Sec. 173.132(a)(2) of this 
subchapter.)
    Settled pressure means the pressure exerted by the contents of a UN 
pressure receptacle in thermal and diffusive equilibrium.
    Sharps. See Sec. 173.134 of this subchapter.
    Shipping paper means a shipping order, bill of lading, manifest or 
other shipping document serving a similar purpose and prepared in 
accordance with subpart C of part 172 of this chapter.

[[Page 115]]

    Siftproof packaging means a packaging impermeable to dry contents, 
including fine solid material produced during transportation.
    Single packaging means a non-bulk packaging other than a combination 
packaging.
    Solid means a material which is not a gas or a liquid.
    Solution means any homogeneous liquid mixture of two or more 
chemical compounds or elements that will not undergo any segregation 
under conditions normal to transportation.
    Special permit means a document issued by the Associate 
Administrator, or other designated Department official, under the 
authority of 49 U.S.C. 5117 permitting a person to perform a function 
that is not otherwise permitted under subchapter A or C of this chapter, 
or other regulations issued under 49 U.S.C. 5101 et seq. (e.g., Federal 
Motor Carrier Safety routing requirements).
    Specification packaging means a packaging conforming to one of the 
specifications or standards for packagings in part 178 or part 179 of 
this subchapter.
    Spontaneously combustible material. See Sec. 173.124(b) of this 
subchapter.
    Stabilized means that the hazardous material is in a condition that 
precludes uncontrolled reaction. This may be achieved by methods such as 
adding an inhibiting chemical, degassing the hazardous material to 
remove dissolved oxygen and inerting the air space in the package, or 
maintaining the hazardous material under temperature control.
    State means a State of the United States, the District of Columbia, 
the Commonwealth of Puerto Rico, the Commonwealth of the Northern 
Mariana Islands, the Virgin Islands, American Samoa, Guam, or any other 
territory or possession of the United States designated by the 
Secretary.
    State-designated route means a preferred route selected in 
accordance with U.S. DOT ``Guidelines for Selecting Preferred Highway 
Routes for Highway Route Controlled Quantities of Radioactive 
Materials'' or an equivalent routing analysis which adequately considers 
overall risk to the public.
    Storage incidental to movement means storage of a transport vehicle, 
freight container, or package containing a hazardous material by any 
person between the time that a carrier takes physical possession of the 
hazardous material for the purpose of transporting it in commerce until 
the package containing the hazardous material is physically delivered to 
the destination indicated on a shipping document, package marking, or 
other medium, or, in the case of a private motor carrier, between the 
time that a motor vehicle driver takes physical possession of the 
hazardous material for the purpose of transporting it in commerce until 
the driver relinquishes possession of the package at its destination and 
is no longer responsible for performing functions subject to the HMR 
with respect to that particular package.
    (1) Storage incidental to movement includes--
    (i) Storage at the destination shown on a shipping document, 
including storage at a transloading facility, provided the shipping 
documentation identifies the shipment as a through-shipment and 
identifies the final destination or destinations of the hazardous 
material; and
    (ii) Rail cars containing hazardous materials that are stored on 
track that does not meet the definition of ``private track or siding'' 
in Sec. 171.8, even if those cars have been delivered to the 
destination shown on the shipping document.
    (2) Storage incidental to movement does not include storage of a 
hazardous material at its final destination as shown on a shipping 
document.
    Stowage means the act of placing hazardous materials on board a 
vessel.
    Strong outer packaging means the outermost enclosure that provides 
protection against the unintentional release of its contents. It is a 
packaging that is sturdy, durable, and constructed so that it will 
retain its contents under normal conditions of transportation. In 
addition, a strong outer packaging must meet the general packaging 
requirements of subpart B of part 173 of this subchapter but need not 
comply with the specification packaging requirements in part 178 of the 
subchapter. For transport by aircraft, a

[[Page 116]]

strong outer packaging is subject to Sec. 173.27 of this subchapter. 
The terms ``strong outside container'' and ``strong outside packaging'' 
are synonymous with ``strong outer packaging.''
    Subsidiary hazard means a hazard of a material other than the 
primary hazard. (See primary hazard).
    Table in Sec. 172.101 or Sec. 172.101 table means the Hazardous 
Materials Table in Sec. 172.101 of this subchapter.
    Technical name means a recognized chemical name or microbiological 
name currently used in scientific and technical handbooks, journals, and 
texts. Generic descriptions are authorized for use as technical names 
provided they readily identify the general chemical group, or 
microbiological group. Examples of acceptable generic chemical 
descriptions are organic phosphate compounds, petroleum aliphatic 
hydrocarbons and tertiary amines. For proficiency testing only, generic 
microbiological descriptions such as bacteria, mycobacteria, fungus, and 
viral samples may be used. Except for names which appear in subpart B of 
part 172 of this subchapter, trade names may not be used as technical 
names.
    TOFC means trailer-on-flat-car.
    Top shell means the tank car tank surface, excluding the head ends 
and bottom shell of the tank car tank.
    Toxin. See Sec. 173.134 of this subchapter.
    Trailership means a vessel, other than a carfloat, specifically 
equipped to carry motor transport vehicles and fitted with installed 
securing devices to tie down each vehicle. The term trailership includes 
Roll-on/Roll-off (RO/RO) vessels.
    Train means one or more engines coupled with one or more rail cars, 
except during switching operations or where the operation is that of 
classifying and assembling rail cars within a railroad yard for the 
purpose of making or breaking up trains.
    Trainship means a vessel other than a rail car ferry or carfloat, 
specifically equipped to transport railroad vehicles, and fitted with 
installed securing devices to tie down each vehicle.
    Transloading means the transfer of a hazardous material by any 
person from one bulk packaging to another bulk packaging, from a bulk 
packaging to a non-bulk packaging, or from a non-bulk packaging to a 
bulk packaging for the purpose of continuing the movement of the 
hazardous material in commerce.
    Transport vehicle means a cargo-carrying vehicle such as an 
automobile, van, tractor, truck, semitrailer, tank car or rail car used 
for the transportation of cargo by any mode. Each cargo-carrying body 
(trailer, rail car, etc.) is a separate transport vehicle.
    Transportation or transport means the movement of property and 
loading, unloading, or storage incidental to that movement.
    UFC means Uniform Freight Classification.
    UN means United Nations.
    UN cylinder means a transportable pressure receptacle with a water 
capacity not exceeding 150 L that has been marked and certified as 
conforming to the applicable requirements in part 178 of this 
subchapter.
    UN portable tank means an intermodal tank having a capacity of more 
than 450 liters (118.9 gallons). It includes a shell fitted with service 
equipment and structural equipment, including stabilizing members 
external to the shell and skids, mountings or accessories to facilitate 
mechanical handling. A UN portable tank must be capable of being filled 
and discharged without the removal of its structural equipment and must 
be capable of being lifted when full. Cargo tanks, rail tank car tanks, 
non-metallic tanks, non-specification tanks, bulk bins, and IBCs and 
packagings made to cylinder specifications are not UN portable tanks.
    UN pressure receptacle means a UN cylinder or tube.
    UN Recommendations means the UN Recommendations on the Transport of 
Dangerous Goods (IBR, see Sec. 171.7).
    UN standard packaging means a packaging conforming to standards in 
the UN Recommendations (IBR, see Sec. 171.7).
    UN tube means a seamless transportable pressure receptacle with a 
water capacity exceeding 150 L but not more than 3,000 L that has been 
marked and certified as conforming to the requirements in part 178 of 
this subchapter.

[[Page 117]]

    Undeclared hazardous material means a hazardous material that is: 
(1) Subject to any of the hazard communication requirements in subparts 
C (Shipping Papers), D (Marking), E (Labeling), and F (Placarding) of 
Part 172 of this subchapter, or an alternative marking requirement in 
Part 173 of this subchapter (such as Sec. Sec. 173.4(a)(10) and 
173.6(c)); and (2) offered for transportation in commerce without any 
visible indication to the person accepting the hazardous material for 
transportation that a hazardous material is present, on either an 
accompanying shipping document, or the outside of a transport vehicle, 
freight container, or package.
    Unintentional release means the escape of a hazardous material from 
a package on an occasion not anticipated or planned. This includes 
releases resulting from collision, package failures, human error, 
criminal activity, negligence, improper packing, or unusual conditions 
such as the operation of pressure relief devices as a result of over-
pressurization, overfill or fire exposure. It does not include releases, 
such as venting of packages, where allowed, and the operational 
discharge of contents from packages.
    Unit load device means any type of freight container, aircraft 
container, aircraft pallet with a net, or aircraft pallet with a net 
over an igloo.
    United States means a State of the United States, the District of 
Columbia, the Commonwealth of Puerto Rico, the Commonwealth of the 
Northern Mariana Islands, the Virgin Islands, American Samoa, Guam, or 
any other territory or possession of the United States designated by the 
Secretary.
    Unloading incidental to movement means removing a packaged or 
containerized hazardous material from a transport vehicle, aircraft, or 
vessel, or for a bulk packaging, emptying a hazardous material from the 
bulk packaging after the hazardous material has been delivered to the 
consignee when performed by carrier personnel or in the presence of 
carrier personnel or, in the case of a private motor carrier, while the 
driver of the motor vehicle from which the hazardous material is being 
unloaded immediately after movement is completed is present during the 
unloading operation. (Emptying a hazardous material from a bulk 
packaging while the packaging is on board a vessel is subject to 
separate regulations as delegated by Department of Homeland Security 
Delegation No. 0170.1 at 2(103).) Unloading incidental to movement 
includes transloading.
    Vessel includes every description of watercraft, used or capable of 
being used as a means of transportation on the water.
    Viscous liquid means a liquid material which has a measured 
viscosity in excess of 2500 centistokes at 25 [deg]C. (77 [deg]F.) when 
determined in accordance with the procedures specified in ASTM Method D 
445-72 ``Kinematic Viscosity of Transparent and Opaque Liquids (and the 
Calculation of Dynamic Viscosity)'' or ASTM Method D 1200-70 ``Viscosity 
of Paints, Varnishes, and Lacquers by Ford Viscosity Cup.''
    Volatility refers to the relative rate of evaporation of materials 
to assume the vapor state.
    Water reactive material. See Sec. 173.124(c) of this subchapter.
    Water resistant means having a degree of resistance to permeability 
by and damage caused by water in liquid form.
    Wooden barrel means a packaging made of natural wood, of round 
cross-section, having convex walls, consisting of staves and heads and 
fitted with hoops.
    Working pressure for purposes of UN pressure receptacles, means the 
settled pressure of a compressed gas at a reference temperature of 15 
[deg]C (59 [deg]F).
    W.T. means watertight.

[Amdt. 171-32, 41 FR 15994, Apr. 15, 1976]

    Editorial Note: For Federal Register citations affecting Sec. 
171.8, see the List of CFR Sections Affected which appears in the 
Finding Aids section of the printed volume and at www.fdsys.gov.



Sec. 171.9  Rules of construction.

    (a) In this subchapter, unless the context requires otherwise:
    (1) Words imparting the singular include the plural;
    (2) Words imparting the plural include the singular; and
    (3) Words imparting the masculine gender include the feminine;

[[Page 118]]

    (b) In this subchapter, the word: (1) ``Shall'' is used in an 
imperative sense;
    (2) ``Must'' is used in an imperative sense;
    (3) ``Should'' is used in a recommendatory sense;
    (4) ``May'' is used in a permissive sense to state authority or 
permission to do the act described, and the words ``no person may * * 
*'' or ``a person may not * * *'' means that no person is required, 
authorized, or permitted to do the act described; and
    (5) ``Includes'' is used as a word of inclusion not limitation.

[Amdt. 171-32, 41 FR 15996, Apr. 15, 1976, as amended by Amdt. 171-32A, 
41 FR 40630, Sept. 20, 1976; Amdt. 171-121, 58 FR 51528, Oct. 1, 1993; 
75 FR 60338, Sept. 30, 2010]



Sec. 171.10  Units of measure.

    (a) General. To ensure compatibility with international 
transportation standards, most units of measure in this subchapter are 
expressed using the International System of Units (``SI'' or metric). 
Where SI units appear, they are the regulatory standard. U.S. standard 
or customary units, which appear in parentheses following the SI units, 
are for information only and are not intended to be the regulatory 
standard.
    (b) Abbreviations for SI units of measure generally used throughout 
this subchapter are as shown in paragraph (c) of this section. Customary 
units shown throughout this subchapter are generally not abbreviated.
    (c) Conversion values. (1) Conversion values are provided in the 
following table and are based on values provided in ASTM E 380, 
``Standard for Metric Practice''.
    (2) If an exact conversion is needed, the following conversion table 
should be used.

                                    Table of Conversion Factors for SI Units
----------------------------------------------------------------------------------------------------------------
            Measurement                  SI to U.S. standard                    U.S. standard to SI
----------------------------------------------------------------------------------------------------------------
Activity...........................  1 TBq=27 Ci................  1 Ci=0.037 TBq
Length.............................  1 cm=0.3937008 in..........  1 in=2.540000 cm
                                     1 m=3.280840 ft............  1 ft=0.3048000 m
Thickness..........................  1 mm=0.03937008 in.........  1 in=25.40000 mm
Mass (weight)......................  1 kg=2.204622 lb...........  1 lb=0.4535924 kg
                                     1 g=0.03527397 oz..........  1 oz=28.34952 g
Pressure...........................  1 kPa=0.1450377 psi........  1 psi=6.894757 kPa
                                     1 Bar=100 kPa=14.504 psi...  1 psi=0.06895 Bar
                                     1 kPa=7.5 mm Hg............
Radiation level....................  1 Sv/hr=100 rem/hr.........  1 rem/hr=0.01 Sv/hr
Volume (liquid)....................  1 L=0.2641720 gal..........  1 gal=3.785412 L
                                     1 mL=0.03381402 oz.........  1 oz=29.57353 mL
                                     1 m\3\=35.31466 ft\3\......  1 ft\3\=0.02831685 m\3\
Density............................  1 kg/m\3\=0.06242797 lb/     1 lb/ft\3\=16.01846 kg/m\3\
                                      ft\3\.
Force..............................  1 Newton = 0.2248 Pound-     1 Pound-force=4.483 N
                                      force.
----------------------------------------------------------------------------------------------------------------
Abbreviation for units of measure are as follows:
Unit of measure and abbreviation:
(SI): millimeter, mm; centimeter, cm; meter, m; gram, g; kilogram, kg; kiloPascal, kPa; liter, L; milliliter,
  mL; cubic meter, m\3\; Terabecquerel, TBq; Gigabecquerel, GBq; millisievert, mSv; Newton, N;
(U.S.): Inch, in; foot, ft; ounce, oz; pound, lb; psig, psi; gallon, gal; cubic feet, ft \3\; Curie, Ci;
  millicurie, mCi; millirem, mrem.


[Amdt. 171-111, 56 FR 66159, Dec. 20, 1991, as amended by Amdt. 171-136, 
60 FR 49108, Sept. 21, 1995; Amdt. 171-135, 60 FR 50302, Sept. 28, 1995; 
66 FR 33335, June 21, 2001; 66 FR 45378, Aug. 28, 2001; 68 FR 75740, 
Dec. 31, 2003]



Sec. 171.11  [Reserved]



Sec. 171.12  North American Shipments.

    (a) Requirements for the use of the Transport Canada TDG 
Regulations. (1) A hazardous material transported from Canada to the 
United States, from the United States to Canada, or transiting the 
United States to Canada or a foreign destination may be offered for 
transportation or transported by motor carrier and rail in accordance 
with the Transport Canada TDG Regulations (IBR, see Sec. 171.7) as 
authorized in Sec. 171.22, provided the requirements in Sec. Sec. 
171.22 and 171.23, as applicable, and this section are met. In addition, 
a cargo tank motor vehicle, portable tank or rail tank car authorized by 
the Transport Canada TDG Regulations

[[Page 119]]

may be used for transportation to, from, or within the United States 
provided the cargo tank motor vehicle, portable tank or rail tank car 
conforms to the applicable requirements of this section. Except as 
otherwise provided in this subpart and subpart C of this part, the 
requirements in parts 172, 173, and 178 of this subchapter do not apply 
for a material transported in accordance with the Transport Canada TDG 
Regulations.
    (2) General packaging requirements. When the provisions of this 
subchapter require a DOT specification or UN standard packaging to be 
used for transporting a hazardous material, a packaging authorized by 
the Transport Canada TDG Regulations may be used, subject to the 
limitations of this part, and only if it is equivalent to the 
corresponding DOT specification or UN packaging (see Sec. 173.24(d)(2) 
of this subchapter) authorized by this subchapter.
    (3) Bulk packagings. A portable tank, cargo tank motor vehicle or 
rail tank car equivalent to a corresponding DOT specification and 
conforming to and authorized by the Transport Canada TDG Regulations may 
be used provided--
    (i) An equivalent type of packaging is authorized for the hazardous 
material according to the Sec. 172.101 table of this subchapter;
    (ii) The portable tank, cargo tank motor vehicle or rail tank car 
conforms to the requirements of the applicable part 173 bulk packaging 
section specified in the Sec. 172.101 table for the material to be 
transported;
    (iii) The portable tank, cargo tank motor vehicle or rail tank car 
conforms to the requirements of all assigned bulk packaging special 
provisions (B codes, and T and TP codes) in Sec. 172.102 of this 
subchapter; and
    (iv) The bulk packaging conforms to all applicable requirements of 
Sec. Sec. 173.31, 173.32, 173.33 and 173.35 of this subchapter, and 
parts 177 and 180 of this subchapter. The periodic retests and 
inspections required by Sec. Sec. 173.31, 173.32 and 173.33 of this 
subchapter may be performed in accordance with part 180 of this 
subchapter or in accordance with the requirements of the TDG Regulations 
provided that the intervals prescribed in part 180 of this subchapter 
are met.
    (v) Rail tank cars must conform to the requirements of Canadian 
General Standards Board standard 43.147 (IBR, see Sec. 171.7).
    (4) Cylinders. When the provisions of this subchapter require that a 
DOT specification or a UN pressure receptacle must be used for a 
hazardous material, a packaging authorized by the Transport Canada TDG 
Regulations may be used only if it corresponds to the DOT specification 
or UN standard authorized by this subchapter. Unless otherwise excepted 
in this subchapter, a cylinder (including a UN pressure receptacle) may 
not be transported unless--
    (i) The packaging is a UN pressure receptacle marked with the 
letters ``CAN'' for Canada as a country of manufacture or a country of 
approval or is a cylinder that was manufactured, inspected and tested in 
accordance with a DOT specification or a UN standard prescribed in part 
178 of this subchapter, except that cylinders not conforming to these 
requirements must meet the requirements in Sec. 171.23. Each cylinder 
must conform to the applicable requirements in part 173 of this 
subchapter for the hazardous material involved.
    (ii) The packaging is a Canadian Transport Commission (CTC) 
specification cylinder manufactured, originally marked and approved in 
accordance with the CTC regulations and in full conformance with the 
Transport Canada TDG Regulations.
    (A) The CTC specification corresponds with a DOT specification and 
the cylinder markings are the same as those specified in this subchapter 
except that they were originally marked with the letters ``CTC'' in 
place of ``DOT'';
    (B) The cylinder has been requalified under a program authorized by 
the Transport Canada TDG Regulations or requalified in accordance with 
the requirements in Sec. 180.205 within the prescribed requalification 
period provided for the corresponding DOT specification;
    (C) When the regulations authorize a cylinder for a specific 
hazardous material with a specification marking prefix

[[Page 120]]

of ``DOT'', a cylinder marked ``CTC'' which otherwise bears the same 
markings that would be required of the specified ``DOT'' cylinder may be 
used; and
    (D) Transport of the cylinder and the material it contains is in all 
other respects in conformance with the requirements of this subchapter 
(e.g. valve protection, filling requirements, operational requirements, 
etc.).
    (5) Class 1 (explosive) materials. When transporting Class 1 
(explosive) material, rail and motor carriers must comply with 49 CFR 
1572.9 and 1572.11 to the extent the requirements apply.
    (6) Primary lithium batteries and cells. Packages containing primary 
lithium batteries and cells that meet the exception in Sec. 172.102, 
Special Provision 188 or 189 of this subchapter must be marked ``PRIMARY 
LITHIUM BATTERIES--FORBIDDEN FOR TRANSPORT ABOARD PASSENGER AIRCRAFT'' 
or ``LITHIUM METAL BATTERIES--FORBIDDEN FOR TRANSPORT ABOARD PASSENGER 
AIRCRAFT.'' The provisions of this paragraph do not apply to packages 
that contain 5 kg (11 pounds) net weight or less of primary lithium 
batteries cells that are contained in or packed with equipment.
    (b) Shipments to or from Mexico. Unless otherwise excepted, 
hazardous materials shipments from Mexico to the United States or from 
the United States to Mexico must conform to all applicable requirements 
of this subchapter. When a hazardous material that is a material 
poisonous by inhalation (see Sec. 171.8) is transported by highway or 
rail from Mexico to the United States, or from the United States to 
Mexico, the following requirements apply:
    (1) The shipping description must include the words ``Toxic 
Inhalation Hazard'' or ``Poison-Inhalation Hazard'' or ``Inhalation 
Hazard'', as required in Sec. 172.203(m) of this subchapter.
    (2) The material must be packaged in accordance with requirements of 
this subchapter.
    (3) The package must be marked in accordance with Sec. 172.313 of 
this subchapter.
    (4) Except as provided in paragraph (e)(5) of this section, the 
package must be labeled or placarded POISON GAS or POISON INHALATION 
HAZARD, as appropriate, in accordance with subparts E and F of this 
subchapter.
    (5) A label or placard that conforms to the UN Recommendations (IBR, 
see Sec. 171.7) specifications for a ``Division 2.3'' or ``Division 
6.1'' label or placard may be substituted for the POISON GAS or POISON 
INHALATION HAZARD label or placard required by Sec. Sec. 172.400(a) and 
172.504(e) of this subchapter on a package transported in a closed 
transport vehicle or freight container. The transport vehicle or freight 
container must be marked with identification numbers for the material, 
regardless of the total quantity contained in the transport vehicle or 
freight container, in the manner specified in Sec. 172.313(c) of this 
subchapter and placarded as required by subpart F of this subchapter.

[Amdt. 171-111, 55 FR 52472, Dec. 21, 1990]

    Editorial Note: For Federal Register citations affecting Sec. 
171.12, see the List of CFR Sections Affected which appears in the 
Finding Aids section of the printed volume and at www.fdsys.gov.



Sec. 171.12a  [Reserved]



Sec. 171.14  [Reserved]



     Subpart B_Incident Reporting, Notification, BOE Approvals and 

                              Authorization



Sec. 171.15  Immediate notice of certain hazardous materials incidents.

    (a) General. As soon as practical but no later than 12 hours after 
the occurrence of any incident described in paragraph (b) of this 
section, each person in physical possession of the hazardous material 
must provide notice by telephone to the National Response Center (NRC) 
on 800-424-8802 (toll free) or 202-267-2675 (toll call) or online at 
http://www.nrc.uscg.mil. Each notice must include the following 
information:
    (1) Name of reporter;
    (2) Name and address of person represented by reporter;
    (3) Phone number where reporter can be contacted;
    (4) Date, time, and location of incident;
    (5) The extent of injury, if any;

[[Page 121]]

    (6) Class or division, proper shipping name, and quantity of 
hazardous materials involved, if such information is available; and
    (7) Type of incident and nature of hazardous material involvement 
and whether a continuing danger to life exists at the scene.
    (b) Reportable incident. A telephone report is required whenever any 
of the following occurs during the course of transportation in commerce 
(including loading, unloading, and temporary storage):
    (1) As a direct result of a hazardous material--
    (i) A person is killed;
    (ii) A person receives an injury requiring admittance to a hospital;
    (iii) The general public is evacuated for one hour or more;
    (iv) A major transportation artery or facility is closed or shut 
down for one hour or more; or
    (v) The operational flight pattern or routine of an aircraft is 
altered;
    (2) Fire, breakage, spillage, or suspected radioactive contamination 
occurs involving a radioactive material (see also Sec. 176.48 of this 
subchapter);
    (3) Fire, breakage, spillage, or suspected contamination occurs 
involving an infectious substance other than a regulated medical waste;
    (4) A release of a marine pollutant occurs in a quantity exceeding 
450 L (119 gallons) for a liquid or 400 kg (882 pounds) for a solid;
    (5) A situation exists of such a nature (e.g., a continuing danger 
to life exists at the scene of the incident) that, in the judgment of 
the person in possession of the hazardous material, it should be 
reported to the NRC even though it does not meet the criteria of 
paragraphs (b)(1), (2), (3) or (4) of this section; or
    (6) During transportation by aircraft, a fire, violent rupture, 
explosion or dangerous evolution of heat (i.e., an amount of heat 
sufficient to be dangerous to packaging or personal safety to include 
charring of packaging, melting of packaging, scorching of packaging, or 
other evidence) occurs as a direct result of a battery or battery-
powered device.
    (c) Written report. Each person making a report under this section 
must also make the report required by Sec. 171.16 of this subpart.

    Note to Sec. 171.15: Under 40 CFR 302.6, EPA requires persons in 
charge of facilities (including transport vehicles, vessels, and 
aircraft) to report any release of a hazardous substance in a quantity 
equal to or greater than its reportable quantity, as soon as that person 
has knowledge of the release, to DOT's National Response Center at (toll 
free) 800-424-8802 or (toll) 202-267-2675.

[68 FR 67759, Dec. 3, 2003, as amended at 72 FR 55684, Oct. 1, 2007; 74 
FR 2233, Jan. 14, 2009; 74 FR 53186, Oct. 16, 2009; 76 FR 43525, July 
20, 2011]



Sec. 171.16  Detailed hazardous materials incident reports.

    (a) General. Each person in physical possession of a hazardous 
material at the time that any of the following incidents occurs during 
transportation (including loading, unloading, and temporary storage) 
must submit a Hazardous Materials Incident Report on DOT Form F 5800.1 
(01/2004) within 30 days of discovery of the incident:
    (1) Any of the circumstances set forth in Sec. 171.15(b);
    (2) An unintentional release of a hazardous material or the 
discharge of any quantity of hazardous waste;
    (3) A specification cargo tank with a capacity of 1,000 gallons or 
greater containing any hazardous material suffers structural damage to 
the lading retention system or damage that requires repair to a system 
intended to protect the lading retention system, even if there is no 
release of hazardous material;
    (4) An undeclared hazardous material is discovered; or
    (5) A fire, violent rupture, explosion or dangerous evolution of 
heat (i.e., an amount of heat sufficient to be dangerous to packaging or 
personal safety to include charring of packaging, melting of packaging, 
scorching of packaging, or other evidence) occurs as a direct result of 
a battery or battery-powered device.
    (b) Providing and retaining copies of the report. Each person 
reporting under this section must--
    (1) Submit a written Hazardous Materials Incident Report to the 
Information Systems Manager, PHH-60, Pipeline and Hazardous Materials 
Safety

[[Page 122]]

Administration, Department of Transportation, East Building, 1200 New 
Jersey Ave., SE., Washington, DC 20590-0001, or an electronic Hazardous 
Material Incident Report to the Information System Manager, PHH-60, 
Pipeline and Hazardous Materials Safety Administration, Department of 
Transportation, Washington, DC 20590-0001 at http://hazmat.dot.gov;
    (2) For an incident involving transportation by aircraft, submit a 
written or electronic copy of the Hazardous Materials Incident Report to 
the FAA Security Field Office nearest the location of the incident; and
    (3) Retain a written or electronic copy of the Hazardous Materials 
Incident Report for a period of two years at the reporting person's 
principal place of business. If the written or electronic Hazardous 
Materials Incident Report is maintained at other than the reporting 
person's principal place of business, the report must be made available 
at the reporting person's principal place of business within 24 hours of 
a request for the report by an authorized representative or special 
agent of the Department of Transportation.
    (c) Updating the incident report. A Hazardous Materials Incident 
Report must be updated within one year of the date of occurrence of the 
incident whenever:
    (1) A death results from injury caused by a hazardous material;
    (2) There was a misidentification of the hazardous material or 
package information on a prior incident report;
    (3) Damage, loss or related cost that was not known when the initial 
incident report was filed becomes known; or
    (4) Damage, loss, or related cost changes by $25,000 or more, or 10% 
of the prior total estimate, whichever is greater.
    (d) Exceptions. Unless a telephone report is required under the 
provisions of Sec. 171.15 of this part, the requirements of paragraphs 
(a), (b), and (c) of this section do not apply to the following 
incidents:
    (1) A release of a minimal amount of material from--
    (i) A vent, for materials for which venting is authorized;
    (ii) The routine operation of a seal, pump, compressor, or valve; or
    (iii) Connection or disconnection of loading or unloading lines, 
provided that the release does not result in property damage.
    (2) An unintentional release of hazardous material when:
    (i) The material is properly classed as--
    (A) ORM-D; or
    (B) a Packing Group III material in Class or Division 3, 4, 5, 6.1, 
8, or 9;
    (ii) Each package has a capacity of less than 20 liters (5.2 
gallons) for liquids or less than 30 kg (66 pounds) for solids;
    (iii) The total aggregate release is less than 20 liters (5.2 
gallons) for liquids or less than 30 kg (66 pounds) for solids; and
    (iv) The material is not--
    (A) Offered for transportation or transported by aircraft,
    (B) A hazardous waste, or
    (C) An undeclared hazardous material.
    (3) An undeclared hazardous material discovered in an air 
passenger's checked or carry-on baggage during the airport screening 
process. (For discrepancy reporting by carriers, see Sec. 175.31 of 
this subchapter.)

[68 FR 67759, Dec. 3, 2003; 69 FR 30119, May 26, 2004, as amended at 70 
FR 56091, Sept. 23, 2005; 74 FR 2233, Jan. 14, 2009; 76 FR 56311, Sept. 
13, 2011]



Sec. Sec. 171.17-171.18  [Reserved]



Sec. 171.19  Approvals or authorizations issued by the Bureau of Explosives.

    Effective December 31, 1998, approvals or authorizations issued by 
the Bureau of Explosives (BOE), other than those issued under part 179 
of this subchapter, are no longer valid.

[63 FR 37459, July 10, 1998]



Sec. 171.20  Submission of Examination Reports.

    (a) When it is required in this subchapter that the issuance of an 
approval by the Associate Administrator be based on an examination by 
the Bureau of Explosives (or any other test facility recognized by 
PHMSA), it is the responsibility of the applicant to

[[Page 123]]

submit the results of the examination to the Associate Administrator.
    (b) Applications for approval submitted under paragraph (a) of this 
section, must be submitted to the Associate Administrator for Hazardous 
Materials Safety, Pipeline and Hazardous Materials Safety 
Administration, Washington, DC 20590-0001.
    (c) Any applicant for an approval aggrieved by an action taken by 
the Associate Administrator, under this subpart may file an appeal with 
the Administrator, PHMSA within 30 days of service of notification of a 
denial.

[Amdt. 171-54, 45 FR 32692, May 19, 1980, as amended by Amdt. 171-66, 47 
FR 43064, Sept. 30, 1982; Amdt. 171-109, 55 FR 39978, Oct. 1, 1990; 
Amdt. 171-111, 56 FR 66162, Dec. 20, 1991; 66 FR 45378, Aug. 28, 2001]



Sec. 171.21  Assistance in investigations and special studies.

    (a) A shipper, carrier, package owner, package manufacturer or 
certifier, repair facility, or person reporting an incident under the 
provisions of Sec. 171.16 must:
    (1) Make all records and information pertaining to the incident 
available to an authorized representative or special agent of the 
Department of Transportation upon request; and
    (2) Give an authorized representative or special agent of the 
Department of Transportation reasonable assistance in the investigation 
of the incident.
    (b) If an authorized representative or special agent of the 
Department of Transportation makes an inquiry of a person required to 
complete an incident report in connection with a study of incidents, the 
person shall:
    (1) Respond to the inquiry within 30 days after its receipt or 
within such other time as the inquiry may specify; and
    (2) Provide true and complete answers to any questions included in 
the inquiry.

[68 FR 67760, Dec. 3, 2003]



 Subpart C_Authorization and Requirements for the Use of International 

                   Transport Standards and Regulations

    Source: 72 FR 25172, May 3, 2007, unless otherwise noted.



Sec. 171.22  Authorization and conditions for the use of international 

standards and regulations.

    (a) Authorized international standards and regulations. This subpart 
authorizes, with certain conditions and limitations, the offering for 
transportation and the transportation in commerce of hazardous materials 
in accordance with the International Civil Aviation Organization's 
Technical Instructions for the Safe Transport of Dangerous Goods by Air 
(ICAO Technical Instructions), the International Maritime Dangerous 
Goods Code (IMDG Code), Transport Canada's Transportation of Dangerous 
Goods Regulations (Transport Canada TDG Regulations), and the 
International Atomic Energy Agency Regulations for the Safe Transport of 
Radioactive Material (IAEA Regulations) (IBR, see Sec. 171.7).
    (b) Limitations on the use of international standards and 
regulations. A hazardous material that is offered for transportation or 
transported in accordance with the international standards and 
regulations authorized in paragraph (a) of this section--
    (1) Is subject to the requirements of the applicable international 
standard or regulation and must be offered for transportation or 
transported in conformance with the applicable standard or regulation; 
and
    (2) Must conform to all applicable requirements of this subpart.
    (c) Materials excepted from regulation under international standards 
and regulations. A material designated as a hazardous material under 
this subchapter, but excepted from or not subject to the international 
transport standards and regulations authorized in paragraph (a) of this 
section (e.g., paragraph 1.16 of the Transport Canada TDG Regulations 
excepts from regulation quantities of hazardous materials less than or 
equal to 500 kg gross transported by rail) must be transported in 
accordance

[[Page 124]]

with all applicable requirements of this subchapter.
    (d) Materials not regulated under this subchapter. Materials not 
designated as hazardous materials under this subchapter but regulated by 
an international transport standard or regulation authorized in 
paragraph (a) of this section may be offered for transportation and 
transported in the United States in full compliance (i.e., packaged, 
marked, labeled, classed, described, stowed, segregated, secured) with 
the applicable international transport standard or regulation.
    (e) Forbidden materials. No person may offer for transportation or 
transport a hazardous material that is a forbidden material or package 
as designated in--
    (1) Section 173.21 of this subchapter;
    (2) Column (3) of the Sec. 172.101 Table of this subchapter;
    (3) Column (9A) of the Sec. 172.101 Table of this subchapter when 
offered for transportation or transported on passenger aircraft or 
passenger railcar; or
    (4) Column (9B) of the Sec. 172.101 Table of this subchapter when 
offered for transportation or transported by cargo aircraft.
    (f) Complete information and certification. (1) Except for shipments 
into the United States from Canada conforming to Sec. 171.12, each 
person importing a hazardous material into the United States must 
provide the forwarding agent at the place of entry into the United 
States timely and complete written information as to the requirements of 
this subchapter applicable to the particular shipment.
    (2) The shipper, directly or through the forwarding agent at the 
place of entry, must provide the initial U.S. carrier with the shipper's 
certification required by Sec. 172.204 of this subchapter, unless the 
shipment is otherwise excepted from the certification requirement. 
Except for shipments for which the certification requirement does not 
apply, a carrier may not accept a hazardous material for transportation 
unless provided a shipper's certification.
    (3) All shipping paper information and package markings required in 
accordance with this subchapter must be in English. The use of shipping 
papers and a package marked with both English and a language other than 
English, in order to dually comply with this subchapter and the 
regulations of a foreign entity, is permitted under this subchapter.
    (4) Each person who provides for transportation or receives for 
transportation (see Sec. Sec. 174.24, 175.30, 176.24 and 177.817 of 
this subchapter) a shipping paper must retain a copy of the shipping 
paper or an electronic image thereof that is accessible at or through 
its principal place of business in accordance with Sec. 172.201(e) of 
this part.
    (g) Additional requirements for the use of international standards 
and regulations. All shipments offered for transportation or transported 
in the United States in accordance with this subpart must conform to the 
following requirements of this subchapter, as applicable:
    (1) The emergency response information requirements in subpart G of 
part 172 of this subchapter;
    (2) The training requirements in subpart H of part 172 of this 
subchapter, including function-specific training in the use of the 
international transport standards and regulations authorized in 
paragraph (a) of this section, as applicable;
    (3) The security requirements in subpart I of part 172 of this 
subchapter;
    (4) The incident reporting requirements in Sec. Sec. 171.15 and 
171.16 of this part for incidents occurring within the jurisdiction of 
the United States including on board vessels in the navigable waters of 
the United States and aboard aircraft of United States registry anywhere 
in air commerce;
    (5) For export shipments, the general packaging requirements in 
Sec. Sec. 173.24 and 173.24a of this subchapter;
    (6) For export shipments, the requirements for the reuse, 
reconditioning, and remanufacture of packagings in Sec. 173.28 of this 
subchapter; and
    (7) The registration requirements in subpart G of part 107 of this 
chapter.

[72 FR 25172, May 3, 2007, as amended at 72 FR 55091 Sept. 28, 2007; 74 
FR 53186, Oct. 16, 2009; 76 FR 56311, Sept. 13, 2011]

[[Page 125]]



Sec. 171.23  Requirements for specific materials and packagings transported 

under the ICAO Technical Instructions, IMDG Code, Transport Canada TDG 

Regulations, or the IAEA Regulations.

    All shipments offered for transportation or transported in the 
United States under the ICAO Technical Instructions, IMDG Code, 
Transport Canada TDG Regulations, or the IAEA Regulations (IBR, see 
Sec. 171.7) must conform to the requirements of this section, as 
applicable.
    (a) Conditions and requirements for cylinders--(1) Except as 
provided in this paragraph, a filled cylinder (pressure receptacle) 
manufactured to other than a DOT specification or a UN standard in 
accordance with part 178 of this subchapter, or a DOT exemption or 
special permit cylinder or a cylinder used as a fire extinguisher in 
conformance with Sec. 173.309(a) of this subchapter, may not be 
transported to, from, or within the United States.
    (2) Cylinders (including UN pressure receptacles) transported to, 
from, or within the United States must conform to the applicable 
requirements of this subchapter. Unless otherwise excepted in this 
subchapter, a cylinder must not be transported unless--
    (i) The cylinder is manufactured, inspected and tested in accordance 
with a DOT specification or a UN standard prescribed in part 178 of this 
subchapter, except that cylinders not conforming to these requirements 
must meet the requirements in paragraphs (a)(3), (a)(4) or (a)(5) of 
this section;
    (ii) The cylinder is equipped with a pressure relief device in 
accordance with Sec. 173.301(f) of this subchapter and conforms to the 
applicable requirements in part 173 of this subchapter for the hazardous 
material involved;
    (iii) The openings on an aluminum cylinder in oxygen service conform 
to the requirements of this paragraph, except when the cylinder is used 
for aircraft parts or used aboard an aircraft in accordance with the 
applicable airworthiness requirements and operating regulations. An 
aluminum DOT specification cylinder must have an opening configured with 
straight (parallel) threads. A UN pressure receptacle may have straight 
(parallel) or tapered threads provided the UN pressure receptacle is 
marked with the thread type, e.g. ``17E, 25E, 18P, or 25P'' and fitted 
with the properly marked valve; and
    (iv) A UN pressure receptacle is marked with ``USA'' as a country of 
approval in conformance with Sec. Sec. 178.69 and 178.70 of this 
subchapter.
    (3) Importation of cylinders for discharge within a single port 
area: A cylinder manufactured to other than a DOT specification or UN 
standard in accordance with part 178 of this subchapter and certified as 
being in conformance with the transportation regulations of another 
country may be authorized, upon written request to and approval by the 
Associate Administrator, for transportation within a single port area, 
provided--
    (i) The cylinder is transported in a closed freight container;
    (ii) The cylinder is certified by the importer to provide a level of 
safety at least equivalent to that required by the regulations in this 
subchapter for a comparable DOT specification or UN cylinder; and
    (iii) The cylinder is not refilled for export unless in compliance 
with paragraph (a)(4) of this section.
    (4) Filling of cylinders for export or for use on board a vessel: A 
cylinder not manufactured, inspected, tested and marked in accordance 
with part 178 of this subchapter, or a cylinder manufactured to other 
than a UN standard, DOT specification, exemption or special permit, may 
be filled with a gas in the United States and offered for transportation 
and transported for export or alternatively, for use on board a vessel, 
if the following conditions are met:
    (i) The cylinder has been requalified and marked with the month and 
year of requalification in accordance with subpart C of part 180 of this 
subchapter, or has been requalified as authorized by the Associate 
Administrator;
    (ii) In addition to other requirements of this subchapter, the 
maximum filling density, service pressure, and pressure relief drive for 
each cylinder conform to the requirements of this part for the gas 
involved; and
    (5) Cylinders not equipped with pressure relief devices: A DOT 
specification

[[Page 126]]

or a UN cylinder manufactured, inspected, tested and marked in 
accordance with part 178 of this subchapter and otherwise conforms to 
the requirements of part 173 for the gas involved, except that the 
cylinder is not equipped with a pressure relief device may be filled 
with a gas and offered for transportation and transported for export if 
the following conditions are met:
    (i) Each DOT specification cylinder or UN pressure receptacle must 
be plainly and durably marked ``For Export Only'';
    (ii) The shipping paper must carry the following certification: 
``This cylinder has (These cylinders have) been retested and refilled in 
accordance with the DOT requirements for export.''; and
    (iii) The emergency response information provided with the shipment 
and available from the emergency response telephone contact person must 
indicate that the pressure receptacles are not fitted with pressure 
relief devices and provide appropriate guidance for exposure to fire.
    (b) Conditions and requirements specific to certain materials--(1) 
Aerosols. Except for a limited quantity of a compressed gas in a 
container of not more than 4 fluid ounces capacity meeting the 
requirements in Sec. 173.306(a)(1) of this subchapter, the proper 
shipping name ``Aerosol,'' UN1950, may be used only for a non-refillable 
receptacle containing a gas compressed, liquefied, or dissolved under 
pressure the sole purpose of which is to expel a nonpoisonous (other 
than Division 6.1, Packing Group III material) liquid, paste, or powder 
and fitted with a self-closing release device (see Sec. 171.8). In 
addition, an aerosol must be in a metal packaging when the packaging 
exceeds 7.22 cubic inches.
    (2) Air bag inflator, air bag module and seat-belt pretensioner. For 
each approved air bag inflator, air bag module and seat-belt 
pretensioner, the shipping paper description must conform to the 
requirements in Sec. 173.166(c) of this subchapter.
    (i) The EX number or product code must be included in association 
with the basic shipping description. When a product code is used, it 
must be traceable to the specific EX number assigned to the inflator, 
module or seat-belt pretensioner by the Associate Administrator. The EX 
number or product code is not required to be marked on the outside 
package.
    (ii) The proper shipping name ``Articles, pyrotechnic for technical 
purposes, UN0431'' must be used for all air bag inflators, air bag 
modules, and seat-belt pretensioners meeting the criteria for a Division 
1.4G material.
    (3) Chemical oxygen generators. Chemical oxygen generators must be 
approved, classed, described, packaged, and transported in accordance 
with the requirements of this subchapter.
    (4) Class 1 (explosive) materials. Prior to being transported, Class 
1 (explosive) materials must be approved by the Associate Administrator 
in accordance with Sec. 173.56 of this subchapter. Each package 
containing a Class 1 (explosive) material must conform to the marking 
requirements in Sec. 172.320 of this subchapter.
    (5) Hazardous substances. A material meeting the definition of a 
hazardous substance as defined in Sec. 171.8, must conform to the 
shipping paper requirements in Sec. 172.203(c) of this subchapter and 
the marking requirements in Sec. 172.324 of this subchapter:
    (i) The proper shipping name must identify the hazardous substance 
by name, or the name of the substance must be entered in parentheses in 
association with the basic description and marked on the package in 
association with the proper shipping name. If the hazardous substance 
meets the definition for a hazardous waste, the waste code (for example, 
D001), may be used to identify the hazardous substance;
    (ii) The shipping paper and the package markings must identify at 
least two hazardous substances with the lowest reportable quantities 
(RQs) when the material contains two or more hazardous substances; and
    (iii) The letters ``RQ'' must be entered on the shipping paper 
either before or after the basic description, and marked on the package 
in association with the proper shipping name for each hazardous 
substance listed.
    (6) Hazardous wastes. A material meeting the definition of a 
hazardous

[[Page 127]]

waste (see Sec. 171.8) must conform to the following:
    (i) The shipping paper and the package markings must include the 
word ``Waste'' immediately preceding the proper shipping name;
    (ii) The shipping paper must be retained by the shipper and by each 
carrier for three years after the material is accepted by the initial 
carrier (see Sec. 172.205(e)(5)); and
    (iii) A hazardous waste manifest must be completed in accordance 
with Sec. 172.205 of this subchapter.
    (7) Marine pollutants. Except for marine pollutants (see Sec. 
171.8) transported in accordance with the IMDG Code, marine pollutants 
transported in bulk packages must meet the shipping paper requirements 
in Sec. 172.203(l) of this subchapter and the package marking 
requirements in Sec. 172.322 of this subchapter.
    (8) Organic peroxides. Organic peroxides not identified by technical 
name in the Organic Peroxide Table in Sec. 173.225(b) of this 
subchapter must be approved by the Associate Administrator in accordance 
with Sec. 173.128(d) of this subchapter.
    (9) [Reserved]
    (10) Poisonous by inhalation materials. A material poisonous by 
inhalation (see Sec. 171.8) must conform to the following requirements:
    (i) The words ``Poison-Inhalation Hazard'' or ``Toxic-Inhalation 
Hazard'' and the words ``Zone A,'' ``Zone B,'' ``Zone C,'' or ``Zone D'' 
for gases, or ``Zone A'' or ``Zone B'' for liquids, as appropriate, must 
be entered on the shipping paper immediately following the basic 
shipping description. The word ``Poison'' or ``Toxic'' or the phrase 
``Poison-Inhalation Hazard'' or ``Toxic-Inhalation Hazard'' need not be 
repeated if it otherwise appears in the shipping description;
    (ii) The material must be packaged in accordance with the 
requirements of this subchapter;
    (iii) The package must be marked in accordance with Sec. 172.313 of 
this subchapter; and
    (iv) Except as provided in subparagraph (B) of this paragraph 
(b)(10)(iv) and for a package containing anhydrous ammonia prepared in 
accordance with the Transport Canada TDG Regulations, the package must 
be labeled or placarded with POISON INHALATION HAZARD or POISON GAS, as 
appropriate, in accordance with Subparts E and F of part 172 of this 
subchapter.
    (A) For a package transported in accordance with the IMDG Code in a 
closed transport vehicle or freight container, a label or placard 
conforming to the IMDG Code specifications for a ``Class 2.3'' or 
``Class 6.1'' label or placard may be substituted for the POISON GAS or 
POISON INHALATION HAZARD label or placard, as appropriate. The transport 
vehicle or freight container must be marked with the identification 
numbers for the hazardous material, regardless of the total quantity 
contained in the transport vehicle or freight container, in the manner 
specified in Sec. 172.313(c) of this subchapter and placarded as 
required by subpart F of part 172 of this subchapter.
    (B) For a package transported in accordance with the Transport 
Canada TDG Regulations in a closed transport vehicle or freight 
container, a label or placard conforming to the TDG Regulations 
specifications for a ``Class 2.3'' or ``Class 6.1'' label or placard may 
be substituted for the POISON GAS or POISON INHALATION HAZARD label or 
placard, as appropriate. The transport vehicle or freight container must 
be marked with the identification numbers for the hazardous material, 
regardless of the total quantity contained in the transport vehicle or 
freight container, in the manner specified in Sec. 172.313(c) of this 
subchapter and placarded as required by subpart F of part 172 of this 
subchapter. While in transportation in the United States, the transport 
vehicle or freight container may also be placarded in accordance with 
the appropriate Transport Canada TDG Regulations in addition to being 
placarded with the POISON GAS or POISON INHALATION HAZARD placards.
    (11) Class 7 (radioactive) materials. (i) Highway route controlled 
quantities (see Sec. 173.403 of this subchapter) must be shipped in 
accordance with Sec. Sec. 172.203(d)(4) and (d)(10); 172.507, and 
173.22(c) of this subchapter;
    (ii) For fissile materials and Type B, Type B(U), and Type B(M) 
packagings,

[[Page 128]]

the competent authority certification and any necessary revalidation 
must be obtained from the appropriate competent authorities as specified 
in Sec. Sec. 173.471, 173.472, and 173.473 of this subchapter, and all 
requirements of the certificates and revalidations must be met;
    (iii) Type A package contents are limited in accordance with Sec. 
173.431 of this subchapter;
    (iv) The country of origin for the shipment must have adopted the 
edition of TS-R-1 of the IAEA Regulations referenced in Sec. 171.7;
    (v) The shipment must conform to the requirements of Sec. 173.448, 
when applicable;
    (vi) The definition for ``radioactive material'' in Sec. 173.403 of 
this subchapter must be applied to radioactive materials transported 
under the provisions of this subpart;
    (vii) Except for limited quantities, the shipment must conform to 
the requirements of Sec. 172.204(c)(4) of this subchapter; and
    (viii) Excepted packages of radioactive material, instruments or 
articles, or articles containing natural uranium or thorium must conform 
to the requirements of Sec. Sec. 173.421, 173.424, or 173.426 of this 
subchapter, as appropriate.
    (12) Self-reactive materials. Self-reactive materials not identified 
by technical name in the Self-reactive Materials Table in Sec. 
173.224(b) of this subchapter must be approved by the Associate 
Administrator in accordance with Sec. 173.124(a)(2)(iii) of this 
subchapter.

[72 FR 25172, May 3, 2007, as amended at 72 FR 55684, Oct. 1, 2007; 73 
FR 57004, Oct. 1, 2008; 76 FR 3345, Jan. 19, 2011; 76 FR 56311, Sept. 
13, 2011]



Sec. 171.24  Additional requirements for the use of the ICAO Technical 

Instructions.

    (a) A hazardous material that is offered for transportation or 
transported within the United States by aircraft, and by motor vehicle 
or rail either before or after being transported by aircraft in 
accordance with the ICAO Technical Instructions (IBR, see Sec. 171.7), 
as authorized in paragraph (a) of Sec. 171.22, must conform to the 
requirements in Sec. 171.22, as applicable, and this section.
    (b) Any person who offers for transportation or transports a 
hazardous material in accordance with the ICAO Technical Instructions 
must comply with the following additional conditions and requirements:
    (1) All applicable requirements in parts 171 and 175 of this 
subchapter (also see 14 CFR 121.135, 121.401, 121.433a, 135.323, 135.327 
and 135.333);
    (2) The quantity limits prescribed in the ICAO Technical 
Instructions for transportation by passenger-carrying or cargo aircraft, 
as applicable;
    (3) The conditions or requirements of a United States variation, 
when specified in the ICAO Technical Instructions.
    (c) Highway transportation. For transportation by highway prior to 
or after transportation by aircraft, a shipment must conform to the 
applicable requirements of part 177 of this subchapter, and the motor 
vehicle must be placarded in accordance with subpart F of part 172.
    (d) Conditions and requirements specific to certain materials. 
Hazardous materials offered for transportation or transported in 
accordance with the ICAO Technical Instructions must conform to the 
following specific conditions and requirements, as applicable:
    (1) Batteries--(i) Nonspillable wet electric storage batteries. 
Nonspillable wet electric storage batteries are not subject to the 
requirements of this subchapter provided--
    (A) The battery meets the conditions specified in Special Provision 
67 of the ICAO Technical Instructions;
    (B) The battery, its outer packaging, and any overpack are plainly 
and durably marked ``NONSPILLABLE'' or ``NONSPILLABLE BATTERY''; and
    (C) The batteries or battery assemblies are offered for 
transportation or transported in a manner that prevents short circuiting 
or forced discharge, including, but not limited to, protection of 
exposed terminals.
    (ii) Primary lithium batteries and cells. Primary lithium batteries 
and cells are forbidden for transportation aboard passenger-carrying 
aircraft. Equipment containing or packed with primary lithium batteries 
or cells are forbidden

[[Page 129]]

for transport aboard passenger-carrying aircraft except as provided in 
Sec. 172.102, Special Provision A101 of this subchapter. When 
transported aboard cargo-only aircraft, packages containing primary 
lithium batteries and cells transported in accordance with Special 
Provision A45 of the ICAO Technical Instructions must be marked 
``PRIMARY LITHIUM BATTERIES--FORBIDDEN FOR TRANSPORT ABOARD PASSENGER 
AIRCRAFT'' or ``LITHIUM METAL BATTERIES--FORBIDDEN FOR TRANSPORT ABOARD 
PASSENGER AIRCRAFT.'' This marking is not required on packages that 
contain 5 kg (11 pounds) net weight or less of primary lithium batteries 
or cells that are contained in or packed with equipment.
    (iii) Prototype lithium batteries and cells. Prototype lithium 
batteries and cells are forbidden for transport aboard passenger 
aircraft and must be approved by the Associate Administrator prior to 
transportation aboard cargo aircraft, in accordance with the 
requirements of Special Provision A55 in Sec. 172.102 of this 
subchapter.
    (2) A package containing Oxygen, compressed, or any of the following 
oxidizing gases must be packaged as required by Parts 173 and 178 of 
this subchapter: carbon dioxide and oxygen mixtures, compressed; 
compressed gas, oxidizing, n.o.s.; liquefied gas, oxidizing, n.o.s.; 
nitrogen trifluoride; and nitrous oxide.

[72 FR 25172, May 3, 2007, as amended at 72 FR 44847, Aug. 9, 2007; 72 
FR 55097, Sept. 28, 2007]



Sec. 171.25  Additional requirements for the use of the IMDG Code.

    (a) A hazardous material may be offered for transportation or 
transported to, from or within the United States by vessel, and by motor 
carrier and rail in accordance with the IMDG Code (IBR, see Sec. 
171.7), as authorized in Sec. 171.22, provided all or part of the 
movement is by vessel. Such shipments must conform to the requirements 
in Sec. 171.22, as applicable, and this section.
    (b) Any person who offers for transportation or transports a 
hazardous material in accordance with the IMDG Code must conform to the 
following additional conditions and requirements:
    (1) Unless specified otherwise in this subchapter, a shipment must 
conform to the requirements in part 176 of this subchapter. For 
transportation by rail or highway prior to or subsequent to 
transportation by vessel, a shipment must conform to the applicable 
requirements of parts 174 and 177 respectively, of this subchapter, and 
the motor vehicle or rail car must be placarded in accordance with 
subpart F of part 172 of this subchapter. When a hazardous material 
regulated by this subchapter for transportation by highway is 
transported by motor vehicle on a public highway or by rail under the 
provisions of subpart C of part 171, the segregation requirements of 
Part 7, Chapter 7.2 of the IMDG Code are authorized.
    (2) For transportation by vessel, the stowage and segregation 
requirements in Part 7 of the IMDG Code may be substituted for the 
stowage and segregation requirements in part 176 of this subchapter.
    (3) Packages containing primary lithium batteries and cells that are 
transported in accordance with Special Provision 188 of the IMDG Code 
must be marked ``PRIMARY LITHIUM BATTERIES--FORBIDDEN FOR TRANSPORT 
ABOARD PASSENGER AIRCRAFT'' or ``LITHIUM METAL BATTERIES--FORBIDDEN FOR 
TRANSPORT ABOARD PASSENGER AIRCRAFT.'' This marking is not required on 
packages that contain 5 kg (11 pounds) net weight or less of primary 
lithium batteries and cells that are contained in or packed with 
equipment.
    (4) Material consigned under UN3166 and UN3171 (e.g., Engines, 
internal combustion, etc., Vehicles, etc. and Battery-powered equipment) 
may be prepared in accordance with the IMDG Code or this subchapter.
    (c) Conditions and requirements for bulk packagings. Except for IBCs 
and UN portable tanks used for the transportation of liquids or solids, 
bulk packagings must conform to the requirements of this subchapter. 
Additionally, the following requirements apply:
    (1) UN portable tanks must conform to the requirements in Special 
Provisions TP37, TP38, TP44 and TP45 when

[[Page 130]]

applicable, and any applicable bulk special provisions assigned to the 
hazardous material in the Hazardous Materials Table in Sec. 172.101 of 
this subchapter;
    (2) IMO Type 5 portable tanks must conform to DOT Specification 51 
or UN portable tank requirements, unless specifically authorized in this 
subchapter or approved by the Associate Administrator;
    (3) Except as specified in this subpart, for a material poisonous 
(toxic) by inhalation, the T Codes specified in Column 13 of the 
Dangerous Goods List in the IMDG Code may be applied to the 
transportation of those materials in IM, IMO and DOT Specification 51 
portable tanks, when these portable tanks are authorized in accordance 
with the requirements of this subchapter; and
    (4) No person may offer an IM or UN portable tank containing liquid 
hazardous materials of Class 3, PG I or II, or PG III with a flash point 
less than 100 [deg]F (38 [deg]C); Division 5.1, PG I or II; or Division 
6.1, PG I or II, for unloading while it remains on a transport vehicle 
with the motive power unit attached, unless it conforms to the 
requirements in Sec. 177.834(o) of this subchapter.
    (d) Use of IMDG Code in port areas. (1) Except for Division 1.1, 
1.2, and Class 7 materials, a hazardous material being imported into or 
exported from the United States or passing through the United States in 
the course of being shipped between locations outside the United States 
may be offered and accepted for transportation and transported by motor 
vehicle within a single port area, including contiguous harbors, when 
packaged, marked, classed, labeled, stowed and segregated in accordance 
with the IMDG Code, offered and accepted in accordance with the 
requirements of subparts C and F of part 172 of this subchapter 
pertaining to shipping papers and placarding, and otherwise conforms to 
the applicable requirements of part 176 of this subchapter.
    (2) The requirement in Sec. 172.201(d) of this subchapter for an 
emergency telephone number does not apply to shipments made in 
accordance with the IMDG Code if the hazardous material is not offloaded 
from the vessel, or is offloaded between ocean vessels at a U.S. port 
facility without being transported by public highway.

[72 FR 25172, May 3, 2007, as amended at 72 FR 44847, Aug. 9, 2007; 73 
FR 57004, Oct. 1, 2008; 74 FR 2233, Jan. 14, 2009; 76 FR 3345, Jan. 19, 
2011]



Sec. 171.26  Additional requirements for the use of the IAEA Regulations.

    A Class 7 (radioactive) material being imported into or exported 
from the United States or passing through the United States in the 
course of being shipped between places outside the United States may be 
offered for transportation or transported in accordance with the IAEA 
Regulations (IBR, see Sec. 171.7) as authorized in paragraph (a) of 
Sec. 171.22, provided the requirements in Sec. 171.22, as applicable, 
are met.



PART 172_HAZARDOUS MATERIALS TABLE, SPECIAL PROVISIONS, HAZARDOUS MATERIALS 

COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING REQUIREMENTS, AND 

SECURITY PLANS--Table of Contents



                            Subpart A_General

Sec.
172.1 Purpose and scope.
172.3 Applicability.

      Subpart B_Table of Hazardous Materials and Special Provisions

172.101 Purpose and use of hazardous materials table.
172.102 Special provisions.

                        Subpart C_Shipping Papers

172.200 Applicability.
172.201 Preparation and retention of shipping papers.
172.202 Description of hazardous material on shipping papers.
172.203 Additional description requirements.
172.204 Shipper's certification.
172.205 Hazardous waste manifest.

                            Subpart D_Marking

172.300 Applicability.
172.301 General marking requirements for non-bulk packagings.
172.302 General marking requirements for bulk packagings.
172.303 Prohibited marking.
172.304 Marking requirements.

[[Page 131]]

172.306 [Reserved]
172.308 Authorized abbreviations.
172.310 Class 7 (radioactive) materials.
172.312 Liquid hazardous materials in non-bulk packagings.
172.313 Poisonous hazardous materials.
172.315 Limited quantities.
172.316 Packagings containing materials classed as ORM-D.
172.317 KEEP AWAY FROM HEAT handling mark.
172.320 Explosive hazardous materials.
172.322 Marine pollutants.
172.323 Infectious substances.
172.324 Hazardous substances in non-bulk packagings.
172.325 Elevated temperature materials.
172.326 Portable tanks.
172.327 Petroleum sour crude oil in bulk packaging.
172.328 Cargo tanks.
172.330 Tank cars and multi-unit tank car tanks.
172.331 Bulk packagings other than portable tanks, cargo tanks, tank 
          cars and multi-unit tank car tanks.
172.332 Identification number markings.
172.334 Identification numbers; prohibited display.
172.336 Identification numbers; special provisions.
172.338 Replacement of identification numbers.

                           Subpart E_Labeling

172.400 General labeling requirements.
172.400a Exceptions from labeling.
172.401 Prohibited labeling.
172.402 Additional labeling requirements.
172.403 Class 7 (radioactive) material.
172.404 Labels for mixed and consolidated packaging.
172.405 Authorized label modifications.
172.406 Placement of labels.
172.407 Label specifications.
172.411 EXPLOSIVE 1.1, 1.2, 1.3, 1.4, 1.5 and 1.6 labels, and EXPLOSIVE 
          Subsidiary label.
172.415 NON-FLAMMABLE GAS label.
172.416 POISON GAS label.
172.417 FLAMMABLE GAS label.
172.419 FLAMMABLE LIQUID label.
172.420 FLAMMABLE SOLID label.
172.422 SPONTANEOUSLY COMBUSTIBLE label.
172.423 DANGEROUS WHEN WET label.
172.426 OXIDIZER label.
172.427 ORGANIC PEROXIDE label.
172.429 POISON INHALATION HAZARD label.
172.430 POISON label.
172.431 [Reserved]
172.432 INFECTIOUS SUBSTANCE label.
172.436 RADIOACTIVE WHITE-I label.
172.438 RADIOACTIVE YELLOW-II label.
172.440 RADIOACTIVE YELLOW-III label.
172.441 FISSILE label.
172.442 CORROSIVE label.
172.444 [Reserved]
172.446 CLASS 9 label.
172.448 CARGO AIRCRAFT ONLY label.
172.450 EMPTY label.

                          Subpart F_Placarding

172.500 Applicability of placarding requirements.
172.502 Prohibited and permissive placarding.
172.503 Identification number display on placards.
172.504 General placarding requirements.
172.505 Placarding for subsidiary hazards.
172.506 Providing and affixing placards: Highway.
172.507 Special placarding provisions: Highway.
172.508 Placarding and affixing placarding: Rail.
172.510 Special placarding provisions: Rail.
172.512 Freight containers and aircraft unit load devices.
172.514 Bulk packagings.
172.516 Visibility and display of placards.
172.519 General specifications for placards.
172.521 DANGEROUS placard.
172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.
172.523 EXPLOSIVES 1.4 placard.
172.524 EXPLOSIVES 1.5 placard.
172.525 EXPLOSIVES 1.6 placard.
172.526 [Reserved]
172.527 Background requirements for certain placards.
172.528 NON-FLAMMABLE GAS placard.
172.530 OXYGEN placard.
172.532 FLAMMABLE GAS placard.
172.536 [Reserved]
172.540 POISON GAS placard.
172.542 FLAMMABLE placard.
172.544 COMBUSTIBLE placard.
172.546 FLAMMABLE SOLID placard.
172.547 SPONTANEOUSLY COMBUSTIBLE placard.
172.548 DANGEROUS WHEN WET placard.
172.550 OXIDIZER placard.
172.552 ORGANIC PEROXIDE placard.
172.553 [Reserved]
172.554 POISON placard.
172.555 POISON INHALATION HAZARD placard.
172.556 RADIOACTIVE placard.
172.558 CORROSIVE placard.
172.560 CLASS 9 placard.

                Subpart G_Emergency Response Information

172.600 Applicability and general requirements.
172.602 Emergency response information.
172.604 Emergency response telephone number.

[[Page 132]]

172.606 Carrier information contact.

                           Subpart H_Training

172.700 Purpose and scope.
172.701 Federal-State relationship.
172.702 Applicability and responsibility for training and testing.
172.704 Training requirements.

                   Subpart I_Safety and Security Plans

172.800 Purpose and applicability.
172.802 Components of a security plan.
172.804 Relationship to other Federal requirements.
172.820 Additional planning requirements for transportation by rail.
172.822 Limitation on actions by states, local governments, and Indian 
          tribes.

Appendix A to Part 172--Office of Hazardous Materials Transportation 
          Color Tolerance Charts and Tables
Appendix B to Part 172--Trefoil Symbol
Appendix C to Part 172--Dimensional Specifications for Recommended 
          Placard Holder
Appendix D to Part 172--Rail Risk Analysis Factors

    Authority: 49 U.S.C. 5101-5128, 44701; 49 CFR 1.53.

    Source: Amdt. 172-29, 41 FR 15996, Apr. 15, 1976, unless otherwise 
noted.



                            Subpart A_General



Sec. 172.1  Purpose and scope.

    This part lists and classifies those materials which the Department 
has designated as hazardous materials for purposes of transportation and 
prescribes the requirements for shipping papers, package marking, 
labeling, and transport vehicle placarding applicable to the shipment 
and transportation of those hazardous materials.

[Amdt. 172-29, 41 FR 15997, Apr. 15, 1976, as amended by 66 FR 45379, 
Aug. 28, 2001]



Sec. 172.3  Applicability.

    (a) This part applies to--
    (1) Each person who offers a hazardous material for transportation, 
and
    (2) Each carrier by air, highway, rail, or water who transports a 
hazardous material.
    (b) When a person, other than one of those provided for in paragraph 
(a) of this section, performs a packaging labeling or marking function 
required by this part, that person shall perform the function in 
accordance with this part.

[Amdt. 172-29, 41 FR 15996, Apr. 15, 1976, as amended by Amdt. 172-32, 
41 FR 38179, Sept. 9, 1976]



      Subpart B_Table of Hazardous Materials and Special Provisions



Sec. 172.101  Purpose and use of hazardous materials table.

    (a) The Hazardous Materials Table (Table) in this section designates 
the materials listed therein as hazardous materials for the purpose of 
transportation of those materials. For each listed material, the Table 
identifies the hazard class or specifies that the material is forbidden 
in transportation, and gives the proper shipping name or directs the 
user to the preferred proper shipping name. In addition, the Table 
specifies or references requirements in this subchapter pertaining to 
labeling, packaging, quantity limits aboard aircraft and stowage of 
hazardous materials aboard vessels.
    (b) Column 1: Symbols. Column 1 of the Table contains six symbols 
(``+'', ``A'', ``D'', ``G'', ``I'' and ``W'') as follows:
    (1) The plus (+) sign fixes the proper shipping name, hazard class 
and packing group for that entry without regard to whether the material 
meets the definition of that class, packing group or any other hazard 
class definition. When the plus sign is assigned to a proper shipping 
name in Column (1) of the Sec. 172.101 Table, it means that the 
material is known to pose a risk to humans. When a plus sign is assigned 
to mixtures or solutions containing a material where the hazard to 
humans is significantly different from that of the pure material or 
where no hazard to humans is posed, the material may be described using 
an alternative shipping name that represents the hazards posed by the 
material. An appropriate alternate proper shipping name and hazard class 
may be authorized by the Associate Administrator.
    (2) The letter ``A'' denotes a material that is subject to the 
requirements of this subchapter only when offered or intended for 
transportation by aircraft, unless the material is a hazardous substance 
or a hazardous waste. A shipping description entry preceded by an

[[Page 133]]

``A'' may be used to describe a material for other modes of 
transportation provided all applicable requirements for the entry are 
met.
    (3) The letter ``D'' identifies proper shipping names which are 
appropriate for describing materials for domestic transportation but may 
be inappropriate for international transportation under the provisions 
of international regulations (e.g., IMO, ICAO). An alternate proper 
shipping name may be selected when either domestic or international 
transportation is involved.
    (4) The letter ``G'' identifies proper shipping names for which one 
or more technical names of the hazardous material must be entered in 
parentheses, in association with the basic description. (See Sec. 
172.203(k).)
    (5) The letter ``I'' identifies proper shipping names which are 
appropriate for describing materials in international transportation. An 
alternate proper shipping name may be selected when only domestic 
transportation is involved.
    (6) The letter ``W'' denotes a material that is subject to the 
requirements of this subchapter only when offered or intended for 
transportation by vessel, unless the material is a hazardous substance 
or a hazardous waste. A shipping description entry preceded by a ``W'' 
may be used to describe a material for other modes of transportation 
provided all applicable requirements for the entry are met.
    (c) Column 2: Hazardous materials descriptions and proper shipping 
names. Column 2 lists the hazardous materials descriptions and proper 
shipping names of materials designated as hazardous materials. 
Modification of a proper shipping name may otherwise be required or 
authorized by this section. Proper shipping names are limited to those 
shown in Roman type (not italics).
    (1) Proper shipping names may be used in the singular or plural and 
in either capital or lower case letters. Words may be alternatively 
spelled in the same manner as they appear in the ICAO Technical 
Instructions or the IMDG Code. For example ``aluminum'' may be spelled 
``aluminium'' and ``sulfur'' may be spelled ``sulphur''. However, the 
word ``inflammable'' may not be used in place of the word ``flammable''.
    (2) Punctuation marks and words in italics are not part of the 
proper shipping name, but may be used in addition to the proper shipping 
name. The word ``or'' in italics indicates that there is a choice of 
terms in the sequence that may alternately be used as the proper 
shipping name or as part of the proper shipping name, as appropriate. 
For example, for the hazardous materials description ``Carbon dioxide, 
solid or Dry ice'' either ``Carbon dioxide, solid'' or ``Dry ice'' may 
be used as the proper shipping name; and for the hazardous materials 
description ``Articles, pressurized pneumatic or hydraulic,'' either 
``Articles, pressurized pneumatic'' or ``Articles, pressurized 
hydraulic'' may be used as the proper shipping name.
    (3) The word ``poison'' or ``poisonous'' may be used interchangeably 
with the word ``toxic'' when only domestic transportation is involved. 
The abbreviation ``n.o.i.'' or ``n.o.i.b.n.'' may be used 
interchangeably with ``n.o.s.''.
    (4) Except for hazardous wastes, when qualifying words are used as 
part of the proper shipping name, their sequence in the package markings 
and shipping paper description is optional. However, the entry in the 
Table reflects the preferred sequence.
    (5) When one entry references another entry by use of the word 
``see'', if both names are in Roman type, either name may be used as the 
proper shipping name (e.g., Ethyl alcohol, see Ethanol).
    (6) When a proper shipping name includes a concentration range as 
part of the shipping description, the actual concentration, if it is 
within the range stated, may be used in place of the concentration 
range. For example, an aqueous solution of hydrogen peroxide containing 
30 percent peroxide may be described as ``Hydrogen peroxide, aqueous 
solution with not less than 20 percent but not more than 40 percent 
hydrogen peroxide'' or ``Hydrogen peroxide, aqueous solution with 30 
percent hydrogen peroxide''.
    (7) Use of the prefix ``mono'' is optional in any shipping name, 
when appropriate. Thus, Iodine monochloride

[[Page 134]]

may be used interchangeably with Iodine chloride. In ``Glycerol alpha-
monochlorohydrin'' the term ``mono'' is considered a prefix to the term 
``chlorohydrin'' and may be deleted.
    (8) Use of the word ``liquid'' or ``solid''. The word ``liquid'' or 
``solid'' may be added to a proper shipping name when a hazardous 
material specifically listed by name may, due to differing physical 
states, be a liquid or solid. When the packaging specified in Column 8 
is inappropriate for the physical state of the material, the table 
provided in paragraph (i)(4) of this section should be used to determine 
the appropriate packaging section.
    (9) Hazardous wastes. If the word ``waste'' is not included in the 
hazardous material description in Column 2 of the Table, the proper 
shipping name for a hazardous waste (as defined in Sec. 171.8 of this 
subchapter), shall include the word ``Waste'' preceding the proper 
shipping name of the material. For example: Waste acetone.
    (10) Mixtures and solutions. (i) A mixture or solution not 
identified specifically by name, comprised of a single predominant 
hazardous material identified in the Table by technical name and one or 
more hazardous and/or non-hazardous material, must be described using 
the proper shipping name of the hazardous material and the qualifying 
word ``mixture'' or ``solution'', as appropriate, unless--
    (A) Except as provided in Sec. 172.101(i)(4) the packaging 
specified in Column 8 is inappropriate to the physical state of the 
material;
    (B) The shipping description indicates that the proper shipping name 
applies only to the pure or technically pure hazardous material;
    (C) The hazard class, packing group, or subsidiary hazard of the 
mixture or solution is different from that specified for the entry;
    (D) There is a significant change in the measures to be taken in 
emergencies;
    (E) The material is identified by special provision in Column 7 of 
the Sec. 172.101 Table as a material poisonous by inhalation; however, 
it no longer meets the definition of poisonous by inhalation or it falls 
within a different hazard zone than that specified in the special 
provision; or
    (F) The material can be appropriately described by a shipping name 
that describes its intended application, such as ``Coating solution'', 
``Extracts, flavoring'' or ``Compound, cleaning liquid.''.
    (ii) If one or more of the conditions specified in paragraph 
(c)(10)(i) of this section is satisfied, then a proper shipping name 
shall be selected as prescribed in paragraph (c)(12)(ii) of this 
section.
    (iii) A mixture or solution not identified in the Table specifically 
by name, comprised of two or more hazardous materials in the same hazard 
class, shall be described using an appropriate shipping description 
(e.g., ``Flammable liquid, n.o.s.''). The name that most appropriately 
describes the material shall be used; e.g., an alcohol not listed by its 
technical name in the Table shall be described as ``Alcohol, n.o.s.'' 
rather than ``Flammable liquid, n.o.s.''. Some mixtures may be more 
appropriately described according to their application, such as 
``Coating solution'' or ``Extracts, flavoring liquid'' rather than by an 
n.o.s. entry. Under the provisions of subparts C and D of this part, the 
technical names of at least two components most predominately 
contributing to the hazards of the mixture or solution may be required 
in association with the proper shipping name.
    (11) Except for a material subject to or prohibited by Sec. 173.21, 
173.54, 173.56(d), 173.56(e), 173.224(c) or 173.225(b) of this 
subchapter, a material that is considered to be a hazardous waste or a 
sample of a material for which the hazard class is uncertain and must be 
determined by testing may be assigned a tentative proper shipping name, 
hazard class, identification number and packing group, if applicable, 
based on the shipper's tentative determination according to:
    (i) Defining criteria in this subchapter;
    (ii) The hazard precedence prescribed in Sec. 173.2a of this 
subchapter;
    (iii) The shipper's knowledge of the material;
    (iv) In addition to paragraphs (c)(11)(i) through (iii) of this 
section,

[[Page 135]]

for a sample of a material other than a waste, the following must be 
met:
    (A) Except when the word ``Sample'' already appears in the proper 
shipping name, the word ``Sample'' must appear as part of the proper 
shipping name or in association with the basic description on the 
shipping paper.
    (B) When the proper shipping description for a sample is assigned a 
``G'' in Column (1) of the Sec. 172.101 Table, and the primary 
constituent(s) for which the tentative classification is based are not 
known, the provisions requiring a technical name for the constituent(s) 
do not apply; and
    (C) A sample must be transported in a combination packaging that 
conforms to the requirements of this subchapter that are applicable to 
the tentative packing group assigned, and may not exceed a net mass of 
2.5 kg (5.5 pounds) per package.

    Note to paragraph (c)(11): For the transportation of samples of 
self-reactive materials, organic peroxides, explosives or lighters, see 
Sec. Sec. 173.224(c)(3), 173.225(c)(2), 173.56(d) or 173.308(b)(2) of 
this subchapter, respectively.

    (12) Except when the proper shipping name in the Table is preceded 
by a plus (+)--
    (i) If it is specifically determined that a material meets the 
definition of a hazard class, packing group or hazard zone, other than 
the class, packing group or hazard zone shown in association with the 
proper shipping name, or does not meet the defining criteria for a 
subsidiary hazard shown in Column 6 of the Table, the material shall be 
described by an appropriate proper shipping name listed in association 
with the correct hazard class, packing group, hazard zone, or subsidiary 
hazard for the material.
    (ii) Generic or n.o.s. descriptions. If an appropriate technical 
name is not shown in the Table, selection of a proper shipping name 
shall be made from the generic or n.o.s. descriptions corresponding to 
the specific hazard class, packing group, hazard zone, or subsidiary 
hazard, if any, for the material. The name that most appropriately 
describes the material shall be used; e.g., an alcohol not listed by its 
technical name in the Table shall be described as ``Alcohol, n.o.s.'' 
rather than ``Flammable liquid, n.o.s.''. Some mixtures may be more 
appropriately described according to their application, such as 
``Coating solution'' or ``Extracts, flavoring, liquid'', rather than by 
an n.o.s. entry, such as ``Flammable liquid, n.o.s.'' It should be 
noted, however, that an n.o.s. description as a proper shipping name may 
not provide sufficient information for shipping papers and package 
markings. Under the provisions of subparts C and D of this part, the 
technical name of one or more constituents which makes the product a 
hazardous material may be required in association with the proper 
shipping name.
    (iii) Multiple hazard materials. If a material meets the definition 
of more than one hazard class, and is not identified in the Table 
specifically by name (e.g., acetyl chloride), the hazard class of the 
material shall be determined by using the precedence specified in Sec. 
173.2a of this subchapter, and an appropriate shipping description 
(e.g., ``Flammable liquid, corrosive n.o.s.'') shall be selected as 
described in paragraph (c)(12)(ii) of this section.
    (iv) If it is specifically determined that a material is not a 
forbidden material and does not meet the definition of any hazard class, 
the material is not a hazardous material.
    (13) Self-reactive materials and organic peroxides. A generic proper 
shipping name for a self-reactive material or an organic peroxide, as 
listed in Column 2 of the Table, must be selected based on the 
material's technical name and concentration, in accordance with the 
provisions of Sec. Sec. 173.224 or 173.225 of this subchapter, 
respectively.
    (14) A proper shipping name that describes all isomers of a material 
may be used to identify any isomer of that material if the isomer meets 
criteria for the same hazard class or division, subsidiary risk(s) and 
packing group, unless the isomer is specifically identified in the 
Table.
    (15) Unless a hydrate is specifically listed in the Table, a proper 
shipping name for the equivalent anhydrous substance may be used, if the 
hydrate meets the same hazard class or division, subsidiary risk(s) and 
packing group.

[[Page 136]]

    (16) Unless it is already included in the proper shipping name in 
the Sec. 172.101 Table, the qualifying words ``liquid'' or ``solid'' 
may be added in association with the proper shipping name when a 
hazardous material specifically listed by name in the Sec. 172.101 
Table may, due to the differing physical states of the various isomers 
of the material, be either a liquid or a solid (for example 
``Dinitrotoluenes, liquid'' and ``Dinitrotoluenes, solid''). Use of the 
words ``liquid'' or ``solid'' is subject to the limitations specified 
for the use of the words ``mixture'' or ``solution'' in paragraph 
(c)(10) of this section. The qualifying word ``molten'' may be added in 
association with the proper shipping name when a hazardous material, 
which is a solid in accordance with the definition in Sec. 171.8 of 
this subchapter, is offered for transportation in the molten state (for 
example, ``Alkylphenols, solid, n.o.s., molten'').
    (d) Column 3: Hazard class or Division. Column 3 contains a 
designation of the hazard class or division corresponding to each proper 
shipping name, or the word ``Forbidden''.
    (1) A material for which the entry in this column is ``Forbidden'' 
may not be offered for transportation or transported. This prohibition 
does not apply if the material is diluted, stabilized or incorporated in 
a device and it is classed in accordance with the definitions of 
hazardous materials contained in part 173 of this subchapter.
    (2) When a reevaluation of test data or new data indicates a need to 
modify the ``Forbidden'' designation or the hazard class or packing 
group specified for a material specifically identified in the Table, 
this data should be submitted to the Associate Administrator.
    (3) A basic description of each hazard class and the section 
reference for class definitions appear in Sec. 173.2 of this 
subchapter.
    (4) Each reference to a Class 3 material is modified to read 
``Combustible liquid'' when that material is reclassified in accordance 
with Sec. 173.150(e) or (f) of this subchapter or has a flash point 
above 60 [deg]C (140 [deg]F) but below 93 [deg]C (200 [deg]F).
    (e) Column 4: Identification number. Column 4 lists the 
identification number assigned to each proper shipping name. Those 
preceded by the letters ``UN'' are associated with proper shipping names 
considered appropriate for international transportation as well as 
domestic transportation. Those preceded by the letters ``NA'' are 
associated with proper shipping names not recognized for international 
transportation, except to and from Canada. Identification numbers in the 
``NA9000'' series are associated with proper shipping names not 
appropriately covered by international hazardous materials (dangerous 
goods) transportation standards, or not appropriately addressed by 
international transportation standards for emergency response 
information purposes, except for transportation between the United 
States and Canada. Those preceded by the letters ``ID'' are associated 
with proper shipping names recognized by the ICAO Technical Instructions 
(IBR, see Sec. 171.7 of this subchapter).
    (f) Column 5: Packing group. Column 5 specifies one or more packing 
groups assigned to a material corresponding to the proper shipping name 
and hazard class for that material. Class 2, Class 7, Division 6.2 
(other than regulated medical wastes), and ORM-D materials, do not have 
packing groups. Packing Groups I, II and III indicate the degree of 
danger presented by the material is either great, medium or minor, 
respectively. If more than one packing group is indicated for an entry, 
the packing group for the hazardous material is determined using the 
criteria for assignment of packing groups specified in subpart D of part 
173. When a reevaluation of test data or new data indicates a need to 
modify the specified packing group(s), the data should be submitted to 
the Associate Administrator. Each reference in this column to a material 
which is a hazardous waste or a hazardous substance, and whose proper 
shipping name is preceded in Column 1 of the Table by the letter ``A'' 
or ``W'', is modified to read ``III'' on those occasions when the 
material is offered for transportation or transported by a mode in which 
its transportation is not otherwise subject to requirements of this 
subchapter.
    (g) Column 6: Labels. Column 6 specifies codes which represent the 
hazard warning labels required for a package

[[Page 137]]

filled with a material conforming to the associated hazard class and 
proper shipping name, unless the package is otherwise excepted from 
labeling by a provision in subpart E of this part, or part 173 of this 
subchapter. The first code is indicative of the primary hazard of the 
material. Additional label codes are indicative of subsidiary hazards. 
Provisions in Sec. 172.402 may require that a label other than that 
specified in Column 6 be affixed to the package in addition to that 
specified in Column 6. No label is required for a material classed as a 
combustible liquid or for a Class 3 material that is reclassed as a 
combustible liquid. For ``Empty'' label requirements, see Sec. 173.428 
of this subchapter. The codes contained in Column 6 are defined 
according to the following table:

                        Label Substitution Table
------------------------------------------------------------------------
                Label code                           Label name
------------------------------------------------------------------------
1.........................................  Explosive
1.1 \1\...................................  Explosive 1.1\1\
1.2 \1\...................................  Explosive 1.2\1\
1.3 \1\...................................  Explosive 1.3\1\
1.4 \1\...................................  Explosive 1.4\1\
1.5 \1\...................................  Explosive 1.5\1\
1.6 \1\...................................  Explosive 1.6\1\
2.1.......................................  Flammable Gas
2.2.......................................  Non-Flammable Gas
2.3.......................................  Poison Gas
3.........................................  Flammable Liquid
4.1.......................................  Flammable Solid
4.2.......................................  Spontaneously Combustible
4.3.......................................  Dangerous When Wet
5.1.......................................  Oxidizer
5.2.......................................  Organic Peroxide
6.1 (inhalation hazard, Zone A or B)......  Poison Inhalation Hazard
6.1 (other than inhalation hazard, Zone A   Poison
 or B) \2\.
6.2.......................................  Infectious substance
7.........................................  Radioactive
8.........................................  Corrosive
9.........................................  Class 9
------------------------------------------------------------------------
\1\ Refers to the appropriate compatibility group letter.
\2\ The packing group for a material is indicated in column 5 of the
  table.

    (h) Column 7: Special provisions. Column 7 specifies codes for 
special provisions applicable to hazardous materials. When Column 7 
refers to a special provision for a hazardous material, the meaning and 
requirements of that special provision are as set forth in Sec. 172.102 
of this subpart.
    (i) Column 8: Packaging authorizations. Columns 8A, 8B and 8C 
specify the applicable sections for exceptions, non-bulk packaging 
requirements and bulk packaging requirements, respectively, in part 173 
of this subchapter. Columns 8A, 8B and 8C are completed in a manner 
which indicates that ``Sec. 173.'' precedes the designated numerical 
entry. For example, the entry ``202'' in Column 8B associated with the 
proper shipping name ``Gasoline'' indicates that for this material 
conformance to non-bulk packaging requirements prescribed in Sec. 
173.202 of this subchapter is required. When packaging requirements are 
specified, they are in addition to the standard requirements for all 
packagings prescribed in Sec. 173.24 of this subchapter and any other 
applicable requirements in subparts A and B of part 173 of this 
subchapter.
    (1) Exceptions. Column 8A contains exceptions from some of the 
requirements of this subchapter. The referenced exceptions are in 
addition to those specified in subpart A of part 173 and elsewhere in 
this subchapter. A ``None'' in this column means no packaging exceptions 
are authorized, except as may be provided by special provisions in 
Column 7.
    (2) Non-bulk packaging. Column 8B references the section in part 173 
of this subchapter which prescribes packaging requirements for non-bulk 
packagings. A ``None'' in this column means non-bulk packagings are not 
authorized, except as may be provided by special provisions in Column 7. 
Each reference in this column to a material which is a hazardous waste 
or a hazardous substance, and whose proper shipping name is preceded in 
Column 1 of the Table by the letter ``A'' or ``W'', is modified to 
include ``Sec. 173.203'' or ``Sec. 173.213'', as appropriate for 
liquids and solids, respectively, on those occasions when the material 
is offered for transportation or transported by a mode in which its 
transportation is not otherwise subject to the requirements of this 
subchapter.
    (3) Bulk packaging. Column (8C) specifies the section in part 173 of 
this subchapter that prescribes packaging requirements for bulk 
packagings, subject to the limitations, requirements, and additional 
authorizations of Columns (7) and (8B). A ``None'' in Column (8C) means 
bulk packagings are not authorized, except as may be provided by special 
provisions in Column (7) and in packaging authorizations Column (8B).

[[Page 138]]

Additional authorizations and limitations for use of UN portable tanks 
are set forth in Column 7. For each reference in this column to a 
material that is a hazardous waste or a hazardous substance, and whose 
proper shipping name is preceded in Column 1 of the Table by the letter 
``A'' or ``W'' and that is offered for transportation or transported by 
a mode in which its transportation is not otherwise subject to the 
requirements of this subchapter:
    (4) For a hazardous material which is specifically named in the 
Table and whose packaging sections specify packagings not applicable to 
the form of the material (e.g., packaging specified is for solid 
material and the material is being offered for transportation in a 
liquid form) the following table should be used to determine the 
appropriate packaging section:

------------------------------------------------------------------------
                                                 Corresponding packaging
Packaging section reference for solid materials     section for liquid
                                                        materials
------------------------------------------------------------------------
Sec.  173.187.................................           Sec.  173.181
Sec.  173.211.................................           Sec.  173.201
Sec.  173.212.................................           Sec.  173.202
Sec.  173.213.................................           Sec.  173.203
Sec.  173.240.................................           Sec.  173.241
Sec.  173.242.................................           Sec.  173.243
------------------------------------------------------------------------

    (5) Cylinders. For cylinders, both non-bulk and bulk packaging 
authorizations are set forth in Column (8B). Notwithstanding a 
designation of ``None'' in Column (8C), a bulk cylinder may be used when 
specified through the section reference in Column (8B).
    (j) Column 9: Quantity limitations. Columns 9A and 9B specify the 
maximum quantities that may be offered for transportation in one package 
by passenger-carrying aircraft or passenger-carrying rail car (Column 
9A) or by cargo aircraft only (Column 9B), subject to the following:
    (1) ``Forbidden'' means the material may not be offered for 
transportation or transported in the applicable mode of transport.
    (2) The quantity limitation is ``net'' except where otherwise 
specified, such as for ``Consumer commodity'' which specifies ``30 kg 
gross.''
    (3) When articles or devices are specifically listed by name, the 
net quantity limitation applies to the entire article or device (less 
packaging and packaging materials) rather than only to its hazardous 
components.
    (4) A package offered or intended for transportation by aircraft and 
which is filled with a material forbidden on passenger-carrying aircraft 
but permitted on cargo aircraft only, or which exceeds the maximum net 
quantity authorized on passenger-carrying aircraft, shall be labelled 
with the CARGO AIRCRAFT ONLY label specified in Sec. 172.448 of this 
part.
    (5) The total net quantity of hazardous material for an outer non-
bulk packaging that contains more than one hazardous material may not 
exceed the lowest permitted maximum net quantity per package as shown in 
Column 9A or 9B, as appropriate. If one material is a liquid and one is 
a solid, the maximum net quantity must be calculated in kilograms. See 
Sec. 173.24a(c)(1)(iv).
    (k) Column 10: Vessel stowage requirements. Column 10A [Vessel 
stowage] specifies the authorized stowage locations on board cargo and 
passenger vessels. Column 10B [Other provisions] specifies codes for 
stowage requirements for specific hazardous materials. The meaning of 
each code in Column 10B is set forth in Sec. 176.84 of this subchapter. 
Section 176.63 of this subchapter sets forth the physical requirements 
for each of the authorized locations listed in Column 10A. (For bulk 
transportation by vessel, see 46 CFR parts 30 to 40, 70, 98, 148, 151, 
153 and 154.) The authorized stowage locations specified in Column 10A 
are defined as follows:
    (1) Stowage category ``A'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel and on a passenger vessel.
    (2) Stowage category ``B'' means--
    (i) The material may be stowed ``on deck'' or ``under deck'' on a 
cargo vessel and on a passenger vessel carrying a number of passengers 
limited to not more than the larger of 25 passengers, or one passenger 
per each 3 m of overall vessel length; and
    (ii) ``On deck only'' on passenger vessels in which the number of 
passengers specified in paragraph (k)(2)(i) of this section is exceeded.
    (3) Stowage category ``C'' means the material must be stowed ``on 
deck

[[Page 139]]

only'' on a cargo vessel and on a passenger vessel.
    (4) Stowage category ``D'' means the material must be stowed ``on 
deck only'' on a cargo vessel and on a passenger vessel carrying a 
number of passengers limited to not more than the larger of 25 
passengers or one passenger per each 3 m of overall vessel length, but 
the material is prohibited on passenger vessels in which the limiting 
number of passengers is exceeded.
    (5) Stowage category ``E'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel and on a passenger vessel 
carrying a number of passengers limited to not more than the larger of 
25 passengers, or one passenger per each 3 m of overall vessel length, 
but is prohibited from carriage on passenger vessels in which the 
limiting number of passengers is exceeded.
    (6) Stowage category ``01'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and on 
a passenger vessel.
    (7) Stowage category ``02'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and 
``on deck'' in closed cargo transport units or ``under deck'' in closed 
cargo transport units on a passenger vessel.
    (8) Stowage category ``03'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) and 
``on deck'' in closed cargo transport units on a passenger vessel.
    (9) Stowage category ``04'' means the material may be stowed ``on 
deck'' or ``under deck'' on a cargo vessel (up to 12 passengers) but the 
material is prohibited on a passenger vessel.
    (10) Stowage category ``05'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' on a cargo 
vessel (up to 12 passengers) and on a passenger vessel.
    (11) Stowage category ``06'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' on a cargo 
vessel (up to 12 passengers) and ``on deck'' in closed cargo transport 
units or ``under deck'' in closed cargo transport units on a passenger 
vessel.
    (12) Stowage category ``07'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' on a cargo 
vessel (up to 12 passengers) and ``on deck'' only in closed cargo 
transport units on a passenger vessel.
    (13) Stowage category ``08'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' on a cargo 
vessel (up to 12 passengers) but the material is prohibited on a 
passenger vessel.
    (14) Stowage category ``09'' means the material may be stowed ``on 
deck only'' in closed cargo transport units or ``under deck'' in closed 
cargo transport units on a cargo vessel (up to 12 passengers) and on a 
passenger vessel.
    (15) Stowage category ``10'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' in closed cargo 
transport units on a cargo vessel (up to 12 passengers) and ``on deck'' 
only in closed cargo transport units on a passenger vessel.
    (16) Stowage category ``11'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' in magazine 
stowage type ``c'' on a cargo vessel (up to 12 passengers) and ``on 
deck'' only in closed cargo transport units on a passenger vessel.
    (17) Stowage category ``12'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' in magazine 
stowage type ``c'' on a cargo vessel (up to 12 passengers) but the 
material is prohibited on a passenger vessel.
    (18) Stowage category ``13'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' in magazine 
stowage type ``A'' on a cargo vessel (up to 12 passengers) and ``on 
deck'' only in closed cargo transport units on a passenger vessel.
    (19) Stowage category ``14'' means the material may be stowed ``on 
deck'' in closed cargo transport units on a cargo vessel (up to 12 
passengers) but the material is prohibited on a passenger vessel.
    (20) Stowage category ``15'' means the material may be stowed ``on 
deck'' in closed cargo transport units or ``under deck'' in closed cargo 
transport units on a cargo vessel (up to 12 passengers)

[[Page 140]]

but the material is prohibited on a passenger vessel.
    (l) Changes to the Table. (1) Unless specifically stated otherwise 
in a rule document published in the Federal Register amending the 
Table--
    (i) Such a change does not apply to the shipment of any package 
filled prior to the effective date of the amendment; and
    (ii) Stocks of preprinted shipping papers and package markings may 
be continued in use, in the manner previously authorized, until depleted 
or for a one-year period, subsequent to the effective date of the 
amendment, whichever is less.
    (2) Except as otherwise provided in this section, any alteration of 
a shipping description or associated entry which is listed in the Sec. 
172.101 Table must receive prior written approval from the Associate 
Administrator.
    (3) The proper shipping name of a hazardous material changed in the 
May 6, 1997 final rule, in effect on October 1, 1997, only by the 
addition or omission of the word ``compressed,'' ``inhibited,'' 
``liquefied'' or ``solution'' may continue to be used to comply with 
package marking requirements, until January 1, 2003.

[[Page 141]]



                                                                            Sec.  172.101 Hazardous Materials Table
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                                          (8)                             (9)             (10)  Vessel  stowage
                                                                                                        ----------------------------------------------------------------------------------------
                                                                                                              Packaging  (Sec.  173.***)        Quantity limitations
         Hazardous materials    Hazard                                                                  ---------------------------------------     (see Sec. Sec.
Symbols    descriptions and    class or    Identification      PG      Label       Special provisions                                             173.27 and 175.75)
           proper shipping     Division        Numbers                 Codes        (Sec.  172.102)                                           ------------------------   Location      Other
                names                                                                                      Exceptions     Non-bulk      Bulk     Passenger     Cargo
                                                                                                                                                 aircraft/   aircraft
                                                                                                                                                   rail        only
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
(1)      (2)................        (3)  (4)                   (5)  (6).......                      (7)  (8A)..........  (8B)......  (8C).....        (9A)        (9B)  (10A)              (10B)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
 
         Accellerene, see p-  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Nitrosodimethylani
          line.
         Accumulators,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          electric, see
          Batteries, wet etc.
         Accumulators,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          pressurized,
          pneumatic or
          hydraulic
          (containing non-
          flamable gas), see
          Articles
          pressurized,
          pneumatic or
          hydraulic
          (containing non-
          flamable gas).
         Acetal.............          3  UN1088                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Acetaldehyde.......          3  UN1089                  I  3.........   A3, B16, T11, TP2, TP7  None..........  201.......  243......   Forbidden        30 L  E            ...........
    A    Acetaldehyde                 9  UN1841                III  9.........  IB8, IP3, IP7, T1, TP33  155...........  204.......  240......      200 kg      200 kg  A                     34
          ammonia.
         Acetaldehyde oxime.          3  UN2332                III  3.........         B1, IB3, T4, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Acetic acid,                 8  UN2789                 II  8, 3......     A3, A6, A7, A10, B2,  154...........  202.......  243......         1 L        30 L  A            ...........
          glacial or Acetic                                                                IB2, T7, TP2
          acid solution,
          with more than 80
          percent acid, by
          mass.
         Acetic acid                  8  UN2790                 II  8.........     A3, A6, A7, A10, B2,  154...........  202.......  242......         1 L        30 L  A            ...........
          solution, not less                                                               IB2, T7, TP2
          than 50 percent
          but not more than
          80 percent acid,
          by mass.
         Acetic acid                  8  UN2790                III  8.........             IB3, T4, TP1  154...........  203.......  242......         5 L        60 L  A            ...........
          solution, with
          more than 10
          percent and less
          than 50 percent
          acid, by mass.
         Acetic anhydride...          8  UN1715                 II  8, 3......     A3, A6, A7, A10, B2,  154...........  202.......  243......         1 L        30 L  A                     40
                                                                                           IB2, T7, TP2
         Acetone............          3  UN1090                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Acetone                    6.1  UN1541                  I  6.1.......    2, B9, B14, B32, B76,  None..........  227.......  244......   Forbidden   Forbidden  D            25, 40, 52,
          cyanohydrin,                                                              B77, N34, T20, TP2,                                                                                       53
          stabilized.                                                                  TP13, TP38, TP45
         Acetone oils.......          3  UN1091                 II  3.........        IB2, T4, TP1, TP8  150...........  202.......  242......         5 L        60 L  B            ...........
         Acetonitrile.......          3  UN1648                 II  3.........             IB2, T7, TP2  150...........  202.......  242......         5 L        60 L  B                     40
         Acetyl acetone       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxide with more
          than 9 percent by
          mass active oxygen.
         Acetyl benzoyl       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxide, solid,
          or with more than
          40 percent in
          solution.

[[Page 142]]

 
         Acetyl bromide.....          8  UN1716                 II  8.........         B2, IB2, T8, TP2  154...........  202.......  242......         1 L        30 L  C                     40
         Acetyl chloride....          3  UN1717                 II  3, 8......    A3, A6, A7, IB1, N34,  150...........  202.......  243......         1 L         5 L  B                     40
                                                                                                T8, TP2
         Acetyl               Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          cyclohexanesulfony
          l peroxide, with
          more than 82
          percent wetted
          with less than 12
          percent water.
         Acetyl iodide......          8  UN1898                 II  8.........   B2, IB2, T7, TP2, TP13  154...........  202.......  242......         1 L        30 L  C                     40
         Acetyl methyl                3  UN2621                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          carbinol.
         Acetyl peroxide,     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solid, or with
          more than 25
          percent in
          solution.
         Acetylene,                 2.1  UN1001              .....  2.1.......                 N86, N88  None..........  303.......  None.....   Forbidden       15 kg  D             25, 40, 57
          dissolved.
         Acetylene            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (liquefied).
         Acetylene silver     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrate.
         Acetylene, solvent   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          free.
         Acetylene            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tetrabromide, see
          Tetrabromoethane.
         Acid butyl           .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          phosphate, see
          Butyl acid
          phosphate.
         Acid, sludge, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Sludge acid.
         Acridine...........        6.1  UN2713                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Acrolein dimer,              3  UN2607                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                     40
          stabilized.
         Acrolein,                  6.1  UN1092                  I  6.1, 3....    1, B9, B14, B30, B42,  None..........  226.......  244......   Forbidden   Forbidden  D                     40
          stabilized.                                                               B77, T22, TP2, TP7,
                                                                                       TP13, TP38, TP44
         Acrylamide, solid..        6.1  UN2074                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     12
         Acrylamide solution        6.1  UN3426                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                     12
         Acrylic acid,                8  UN2218                 II  8, 3......         B2, IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  C                 25, 40
          stabilized.
         Acrylonitrile,               3  UN1093                  I  3, 6.1....       B9, T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  E                     40
          stabilized.
         Actuating            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          cartridge,
          explosive, see
          Cartridges, power
          device.
         Adhesives,                   3  UN1133                  I  3.........      T11, TP1, TP8, TP27  150...........  201.......  243......         1 L        30 L  B
          containing a
          flammable liquid.
                              .........  ..................     II  3.........  149, B52, IB2, T4, TP1,  150...........  173.......  242......         5 L        60 L  B            ...........
                                                                                                    TP8
                              .........  ..................    III  3.........    B1, B52, IB3, T2, TP1  150...........  173.......  242......        60 L       220 L  A            ...........
         Adiponitrile.......        6.1  UN2205                III  6.1.......             IB3, T3, TP1  153...........  203.......  241......        60 L       220 L  A            ...........

[[Page 143]]

 
         Aerosols, poison,          2.2  UN1950              .....  2.2, 6.1..  .......................  306...........  None......  None.....   Forbidden   Forbidden  A            48, 87, 126
          Packing Group III
          (each not
          exceeding 1 L
          capacity).
         Aerosols,                  2.1  UN1950              .....  2.1.......                      N82  306...........  None......  None.....       75 kg      150 kg  A            48, 87, 126
          flammable, (each
          not exceeding 1 L
          capacity).
         Aerosols,                  2.1  UN1950              .....  2.1.......                      N82  306...........  304.......  None.....   Forbidden      150 kg  A            48, 87, 126
          flammable, n.o.s.
          (engine starting
          fluid) (each not
          exceeding 1 L
          capacity).
         Aerosols, non-             2.2  UN1950              .....  2.2.......  .......................  306...........  None......  None.....       75 kg      150 kg  A                48, 87,
          flammable,(each                                                                                                                                                                   126.
          not exceeding 1 L
          capacity).
         Aerosols, poison,          2.2  UN1950              .....  2.2, 6.1..  .......................  306...........  None......  None.....   Forbidden   Forbidden  A            48, 87, 126
          (each not
          exceeding 1 L
          capacity).
    I    Air bag inflators,        1.4G  UN0503                 II  1.4G......                      161  None..........  62........  None.....   Forbidden       75 kg  02           ...........
          or Air bag
          modules, or Seat-
          belt
          pretensioners..
         Air bag inflators,           9  UN3268                III  9.........                      160  166...........  166.......  166......       25 kg      100 kg  A            ...........
          or Air bag
          modules, or Seat-
          belt
          pretensioners..
         Air, compressed....        2.2  UN1002              .....  2.2.......                       78  306, 307......  302.......  302......       75 kg      150 kg  A            ...........
         Air, refrigerated          2.2  UN1003              .....  2.2, 5.1..           T75, TP5, TP22  320...........  316.......  318, 319.   Forbidden   Forbidden  D                     51
          liquid, (cryogenic
          liquid).
         Air, refrigerated          2.2  UN1003              .....  2.2, 5.1..           T75, TP5, TP22  320...........  316.......  318, 319.   Forbidden   Forbidden  D                     51
          liquid, (cryogenic
          liquid) non-
          pressurized.
         Aircraft engines     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (including
          turbines), see
          Engines, internal
          combustion.
         Aircraft evacuation  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          slides, see Life
          saving appliances
          etc.
         Aircraft hydraulic           3  UN3165                  I  3, 6.1, 8.  .......................  None..........  172.......  None.....   Forbidden        42 L  E            ...........
          power unit fuel
          tank (containing a
          mixture of
          anhydrous
          hydrazine and
          monomethyl
          hydrazine) (M86
          fuel).
         Aircraft survival    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          kits, see Life
          saving appliances
          etc.
    G    Alcoholates                  3  UN3274                 II  3, 8......                      IB2  150...........  202.......  243......         1 L         5 L  B            ...........
          solution, n.o.s.,
          in alcohol.
         Alcoholic beverages          3  UN3065                 II  3.........    24, 149, B1, IB2, T4,  150...........  202.......  242......         5 L        60 L  A            ...........
                                                                                                    TP1
         ...................  .........  ..................    III  3.........    24, B1, IB3, N11, T2,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                    TP1
         Alcohols, n.o.s....          3  UN1987                  I  3.........      172, T11, TP1, TP8,  4b............  201.......  243......         1 L        30 L  E
                                                                                                   TP27
                              .........  ..................     II  3.........  172, IB2, T7, TP1, TP8,  4b, 150.......  202.......  242......         5 L        60 L  B
                                                                                                   TP28
                              .........  ..................    III  3.........   172, B1, IB3, T4, TP1,  4b, 150.......  203.......  242......        60 L       220 L  A
                                                                                                   TP29
    G    Alcohols,                    3  UN1986                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  E                     40
          flammable, toxic
          n.o.s.
                                                                II  3, 6.1....      IB2, T11, TP2, TP27  150...........  202.......  243......         1 L        60 L  B                     40
                                                               III  3, 6.1....   B1, IB3, T7, TP1, TP28  150...........  203.......  242......        60 L       220 L  A            ...........

[[Page 144]]

 
         Aldehydes, n.o.s...          3  UN1989                  I  3.........           T11, TP1, TP27  None..........  201.......  243......         1 L        30 L  E            ...........
         ...................  .........  ..................     II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, IB3, T4, TP1, TP29  150...........  203.......  242......        60 L       220 L  A            ...........
    G    Aldehydes,                   3  UN1988                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  E                     40
          flammable, toxic,
          n.o.s..
         ...................  .........  ..................     II  3, 6.1....      IB2, T11, TP2, TP27  150...........  202.......  243......         1 L        60 L  B                     40
         ...................  .........  ..................    III  3, 6.1....   B1, IB3, T7, TP1, TP28  150...........  203.......  242......        60 L       220 L  A            ...........
         Aldol..............        6.1  UN2839                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     12
    G    Alkali metal               4.2  UN3206                 II  4.2, 8....    64, A7, IB5, IP2, T3,  None..........  212.......  242......       15 kg       50 kg  B            ...........
          alcoholates, self-                                                                       TP33
          heating,
          corrosive, n.o.s..
         ...................  .........  ..................    III  4.2, 8....    64, A7, IB8, IP3, T1,  None..........  213.......  242......       25 kg      100 kg  B            ...........
                                                                                                   TP33
         Alkali metal               4.3  UN1421                  I  4.3.......     A2, A3, A7, B48, N34  None..........  201.......  244......   Forbidden         1 L  D                     52
          alloys, liquid,
          n.o.s..
         Alkali metal               4.3  UN1389                  I  4.3.......          A2, A3, A7, N34  None..........  201.......  244......   Forbidden         1 L  D                 40, 52
          amalgam, liquid.
         Alkali metal               4.3  UN3401                  I  4.3.......  IB4, IP1, N40, T9, TP7,  None..........  211.......  242......   Forbidden       15 kg  D                     52
          amalgam, solid.                                                                          TP33
         Alkali metal amides        4.3  UN1390                 II  4.3.......    A6, A7, A8, A19, A20,  151...........  212.......  241......       15 kg       50 kg  E                 40, 52
                                                                                     IB7, IP2, T3, TP33
         Alkali metal               4.3  UN3482                  I  4.3, 3....               A2, A3, A7  None..........  201.......  244......   Forbidden         1 L  D                     52
          dispersions,
          flammable or
          Alkaline earth
          metal dispersions,
          flammable.
         Alkali metal               4.3  UN1391                  I  4.3.......               A2, A3, A7  None..........  201.......  244......   Forbidden         1 L  D                     52
          dispersions, or
          Alkaline earth
          metal dispersions.
         Alkaline corrosive   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          liquids, n.o.s.,
          see Caustic alkali
          liquids, n.o.s..
    G    Alkaline earth             4.2  UN3205                 II  4.2.......    65, A7, IB6, IP2, T3,  None..........  212.......  241......       15 kg       50 kg  B            ...........
          metal alcoholates,                                                                       TP33
          n.o.s..
         ...................  .........  ..................    III  4.2.......    65, A7, IB8, IP3, T1,  None..........  213.......  241......       25 kg      100 kg  B            ...........
                                                                                                   TP33
         Alkaline earth             4.3  UN1393                 II  4.3.......  A19, IB7, IP2, T3, TP33  151...........  212.......  241......       15 kg       50 kg  E                     52
          metal alloys,
          n.o.s..
         Alkaline earth             4.3  UN1392                  I  4.3.......            A19, N34, N40  None..........  201.......  244......   Forbidden         1 L  E                 40, 52
          metal amalgams,
          liquid.
         Alkaline earth             4.3  UN3402                  I  4.3.......  A19, N34, N40, T9, TP7,  None..........  211.......  242......   Forbidden       15 kg  D                     52
          metal amalgams,                                                                          TP33
          solid.
    G    Alkaloids, liquid,         6.1  UN3140                  I  6.1.......       A4, T14, TP2, TP27  None..........  201.......  243......         1 L        30 L  A            ...........
          n.o.s., or
          Alkaloid salts,
          liquid, n.o.s..

[[Page 145]]

 
         ...................  .........  ..................     II  6.1.......      IB2, T11, TP2, TP27  153...........  202.......  243......         5 L        60 L  A            ...........
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP1, TP28  153...........  203.......  241......        60 L       220 L  A            ...........
    G    Alkaloids, solid,          6.1  UN1544                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A            ...........
          n.o.s. or Alkaloid
          salts, solid,
          n.o.s. poisonous.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Alkyl sulfonic               8  UN2584                 II  8.........   B2, IB2, T8, TP2, TP13  154...........  202.......  242......         1 L        30 L  B            ...........
          acids, liquid or
          Aryl sulfonic
          acids, liquid with
          more than 5
          percent free
          sulfuric acid.
         Alkyl sulfonic               8  UN2586                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  B            ...........
          acids, liquid or
          Aryl sulfonic
          acids, liquid with
          not more than 5
          percent free
          sulfuric acid.
         Alkyl sulfonic               8  UN2583                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A            ...........
          acids, solid or
          Aryl sulfonic
          acids, solid, with
          more than 5
          percent free
          sulfuric acid.
         Alkyl sulfonic               8  UN2585                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
          acids, solid or
          Aryl sulfonic
          acids, solid with
          not more than 5
          percent free
          sulfuric acid.
         Alkylphenols,                8  UN3145                  I  8.........             A6, T14, TP2  None..........  201.......  243......       0.5 L       2.5 L  B            ...........
          liquid, n.o.s.
          (including C2-C12
          homologues).
         ...................  .........  ..................     II  8.........      IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B            ...........
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A            ...........
         Alkylphenols,                8  UN2430                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B            ...........
          solid, n.o.s.
          (including C2-C12
          homologues).
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B            ...........
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
         Alkylsulfuric acids          8  UN2571                 II  8.........  B2, IB2, T8, TP2, TP13,  154...........  202.......  242......         1 L        30 L  C                     14
                                                                                                   TP28
         Allethrin, see       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Pesticides,
          liquid, toxic,
          n.o.s..
         Allyl acetate......          3  UN2333                 II  3, 6.1....       IB2, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
         Allyl alcohol......        6.1  UN1098                  I  6.1, 3....    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Allyl bromide......          3  UN1099                  I  3, 6.1....           T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  B                     40
         Allyl chloride.....          3  UN1100                  I  3, 6.1....           T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  E                     40
         Allyl                .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          chlorocarbonate,
          see Allyl
          chloroformate.
         Allyl chloroformate        6.1  UN1722                  I  6.1, 3, 8.    2, B9, B14, B32, N41,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Allyl ethyl ether..          3  UN2335                 II  3, 6.1....       IB2, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
         Allyl formate......          3  UN2336                  I  3, 6.1....           T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  E                     40
         Allyl glycidyl               3  UN2219                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          ether.

[[Page 146]]

 
         Allyl iodide.......          3  UN1723                 II  3, 8......    A3, A6, IB1, N34, T7,  150...........  202.......  243......         1 L         5 L  B                     40
                                                                                              TP2, TP13
         Allyl                      6.1  UN1545                 II  6.1, 3....     A3, A7, IB2, T7, TP2  None..........  202.......  243......   Forbidden        60 L  D                     40
          isothiocyanate,
          stabilized.
         Allylamine.........        6.1  UN2334                  I  6.1, 3....    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  TP2, TP13, TP38, TP45
         Allyltrichlorosilan          8  UN1724                 II  8, 3......    A7, B2, B6, N34, T10,  None..........  206.......  243......   Forbidden        30 L  C                     40
          e, stabilized.                                                                 TP2, TP7, TP13
         Aluminum                   4.2  UN2870                  I  4.2, 4.3..      B11, T21, TP7, TP33  None..........  181.......  244......   Forbidden   Forbidden  D            ...........
          borohydride or
          Aluminum
          borohydride in
          devices.
         Aluminum bromide,            8  UN1725                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                     40
          anhydrous.
         Aluminum bromide,            8  UN2580                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          solution.
         Aluminum carbide...        4.3  UN1394                 II  4.3.......  A20, IB7, IP2, N41, T3,  151...........  212.......  242......       15 kg       50 kg  A                     52
                                                                                                   TP33
         Aluminum chloride,           8  UN1726                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                     40
          anhydrous.
         Aluminum chloride,           8  UN2581                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          solution.
         Aluminum dross, wet  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          or hot.
         Aluminum                   4.3  UN1395                 II  4.3, 6.1..  A19, IB5, IP2, T3, TP33  151...........  212.......  242......       15 kg       50 kg  A            39, 40, 52,
          ferrosilicon                                                                                                                                                               53, 85, 103
          powder.
         ...................  .........  ..................    III  4.3, 6.1..            A19, A20, IB4  151...........  213.......  241......       25 kg      100 kg  A            39, 40, 52,
                                                                                                                                                                                     53, 85, 103
         Aluminum hydride...        4.3  UN2463                  I  4.3.......                 A19, N40  None..........  211.......  242......   Forbidden       15 kg  E            ...........
    D    Aluminum, molten...          9  NA9260                III  9.........             IB3, T1, TP3  None..........  None......  247......   Forbidden   Forbidden  D            ...........
         Aluminum nitrate...        5.1  UN1438                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            ...........
                                                                                                   TP33
         Aluminum phosphate   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solution, see
          Corrosive liquids,
          etc.
         Aluminum phosphide.        4.3  UN1397                  I  4.3, 6.1..             A8, A19, N40  None..........  211.......  242......   Forbidden       15 kg  E             40, 52, 85
         Aluminum phosphide         6.1  UN3048                  I  6.1.......   A8, IB7, IP1, T6, TP33  None..........  211.......  242......   Forbidden       15 kg  E                 40, 85
          pesticides.
         Aluminum powder,           4.1  UN1309                 II  4.1.......  IB8, IP2, IP4, T3, TP33  151...........  212.......  240......       15 kg       50 kg  A            13, 39, 52,
          coated.                                                                                                                                                                    53, 74, 101
         ...................  .........  ..................    III  4.1.......       IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A            13, 39, 52,
                                                                                                                                                                                     53, 74, 101
         Aluminum powder,           4.3  UN1396                 II  4.3.......  A19, A20, IB7, IP2, T3,  151...........  212.......  242......       15 kg       50 kg  A             39, 52, 53
          uncoated.                                                                                TP33
         ...................  .........  ..................    III  4.3.......  A19, A20, IB8, IP4, T1,  151...........  213.......  241......       25 kg      100 kg  A             39, 52, 53
                                                                                                   TP33
         Aluminum resinate..        4.1  UN2715                III  4.1.......            IB6, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A            ...........

[[Page 147]]

 
         Aluminum silicon           4.3  UN1398                III  4.3.......   A1, A19, IB8, IP4, T1,  151...........  213.......  241......       25 kg      100 kg  A            39, 40, 52,
          powder, uncoated.                                                                        TP33                                                                              53, 85, 103
         Aluminum smelting          4.3  UN3170                 II  4.3.......     128, B115, IB7, IP2,  None..........  212.......  242......       15 kg       50 kg  B                85, 103
          by-products or                                                                       T3, TP33
          Aluminum remelting
          by-products.
         ...................  .........  ..................    III  4.3.......     128, B115, IB8, IP4,  None..........  213.......  241......       25 kg      100 kg  B                85, 103
                                                                                               T1, TP33
         Amatols, see         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Explosives,
          blasting, type B.
    G    Amine, flammable,            3  UN2733                  I  3, 8......           T14, TP1, TP27  None..........  201.......  243......       0.5 L       2.5 L  D                 40, 52
          corrosive, n.o.s.
          or Polyamines,
          flammable,
          corrosive, n.o.s.
                                                                II  3, 8......      IB2, T11, TP1, TP27  150...........  202.......  243......         1 L         5 L  B                 40, 52
                                                               III  3, 8......   B1, IB3, T7, TP1, TP28  150...........  203.......  242......         5 L        60 L  A                 40, 52
    G    Amine, liquid,               8  UN2734                  I  8, 3......   A3, A6, N34, T14, TP2,  None..........  201.......  243......       0.5 L       2.5 L  A                     52
          corrosive,                                                                               TP27
          flammable, n.o.s.
          or Polyamines,
          liquid, corrosive,
          flammable, n.o.s.
                                                                II  8, 3......      IB2, T11, TP2, TP27  None..........  202.......  243......         1 L        30 L  A                     52
    G    Amines, liquid,              8  UN2735                  I  8.........   A3, A6, B10, N34, T14,  None..........  201.......  243......       0.5 L       2.5 L  A                     52
          corrosive, n.o.s.,                                                                  TP2, TP27
          or Polyamines,
          liquid, corrosive,
          n.o.s..
         ...................  .........  ..................     II  8.........  B2, IB2, T11, TP1, TP27  154...........  202.......  242......         1 L        30 L  A                     52
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     52
    G    Amines, solid,               8  UN3259                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  A                     52
          corrosive, n.o.s.,
          or Polyamines,
          solid, corrosive
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                     52
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                     52
         2-Amino-4-                 6.1  UN2673                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
          chlorophenol.
         2-Amino-5-                 6.1  UN2946                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          diethylaminopentan
          e.
         2-Amino-4,6-               4.1  UN3317                  I  4.1.......    23, A8, A19, A20, N41  None..........  211.......  None.....        1 kg       15 kg  E                 28, 36
          Dinitrophenol,
          wetted with not
          less than 20
          percent water by
          mass.
         2-(2-Aminoethoxy)            8  UN3055                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          ethanol.
         N-                           8  UN2815                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                     12
          Aminoethylpiperazi
          ne.
    +    Aminophenols (o-; m-       6.1  UN2512                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          ; p-).
         Aminopropyldiethano  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          lamine, see
          Amines, etc.
         n-                   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Aminopropylmorphol
          ine, see Amines,
          etc.
         Aminopyridines (o-;        6.1  UN2671                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B            12, 40, 52.
          m-; p-).
    I    Ammonia, anhydrous.        2.3  UN1005              .....  2.3, 8....              4, N87, T50  None..........  304.......  314, 315.   Forbidden   Forbidden  D             40, 52, 57
    D    Ammonia, anhydrous.        2.2  UN1005              .....  2.2.......                  13, T50  None..........  304.......  314, 315.   Forbidden   Forbidden  D             40, 52, 57
    I    Ammonia solution,          2.3  UN3318              .....  2.3, 8....              4, N87, T50  None..........  304.......  314, 315.   Forbidden   Forbidden  D             40, 52, 57
          relative density
          less than 0.880 at
          15 degrees C in
          water, with more
          than 50 percent
          ammonia.

[[Page 148]]

 
    D    Ammonia solution,          2.2  UN3318              .....  2.2.......                  13, T50  None..........  304.......  314, 315.   Forbidden   Forbidden  D             40, 52, 57
          relative density
          less than 0.880 at
          15 degrees C in
          water, with more
          than 50 percent
          ammonia.
         Ammonia solutions,         2.2  UN2073              .....  2.2.......                      N87  306...........  304.......  314, 315.   Forbidden      150 kg  E             40, 52, 57
          relative density
          less than 0.880 at
          15 degrees C in
          water, with more
          than 35 percent
          but not more than
          50 percent ammonia.
         Ammonia solution,            8  UN2672                III  8.........        IB3, IP8, T7, TP1  154...........  203.......  241......         5 L        60 L  A             40, 52, 85
          relative density
          between 0.880 and
          0.957 at 15
          degrees C in
          water, with more
          than 10 percent
          but not more than
          35 percent ammonia.
         Ammonium arsenate..        6.1  UN1546                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     53
         Ammonium azide.....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ammonium             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          bifluoride, solid,
          see Ammonium
          hydrogen
          difluoride, solid.
         Ammonium bifluoride  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solution, see
          Ammonium hydrogen
          difluoride,
          solution.
         Ammonium bromate...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ammonium chlorate..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ammonium dichromate        5.1  UN1439                 II  5.1.......  IB8, IP2, IP4, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A                     52
         Ammonium dinitro-o-        6.1  UN1843                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B            36, 65, 66,
          cresolate, solid.                                                                                                                                                                   77
         Ammonium dinitro-o-        6.1  UN3424                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B            36, 66, 78,
          cresolate solution.                                                                                                                                                                 91
         ...................  .........  ..................    III  6.1.......             IB2, T7, TP2  153...........  203.......  241......        60 L       220 L  A            36, 66, 78,
                                                                                                                                                                                              91
         Ammonium fluoride..        6.1  UN2505                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     52
         Ammonium                   6.1  UN2854                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     52
          fluorosilicate.
         Ammonium fulminate.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ammonium hydrogen            8  UN2506                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                     40
          sulfate.

[[Page 149]]

 
         Ammonium                     8  UN1727                 II  8.........  IB8, IP2, IP4, N34, T3,  154...........  212.......  240......       15 kg       50 kg  A             25, 40, 52
          hydrogendifluoride                                                                       TP33
          , solid.
         Ammonium                     8  UN2817                 II  8, 6.1....  IB2, N34, T8, TP2, TP13  154...........  202.......  243......         1 L        30 L  B                     40
          hydrogendifluoride
          , solution.
         ...................  .........  ..................    III  8, 6.1....  IB3, N3, T4, TP1 , TP13  154...........  203.......  241......         5 L        60 L  B                 40, 95
         Ammonium             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydrosulfide,
          solution, see
          Ammonium sulfide
          solution.
    D    Ammonium hydroxide,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ammonia
          solutions, etc.
         Ammonium                   6.1  UN2859                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                44, 89,
          metavanadate.                                                                                                                                                                 100, 141
         Ammonium nitrate           5.1  UN2067                III  5.1.......   52, 150, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  B            48, 59, 60,
          based fertilizer.                                                                        TP33                                                                                  66, 117
  A W    Ammonium nitrate             9  UN2071                III  9.........            132, IB8, IP3  155...........  213.......  240......      200 kg      200 kg  A            ...........
          based fertilizer.
         Ammonium nitrate           5.1  UN3375                 II  5.1.......                 147, 163  None..........  214.......  214......   Forbidden   Forbidden  D            48, 59, 60,
          emulsion or                                                                                                                                                                    66, 124
          Ammonium nitrate
          suspension or
          Ammonium nitrate
          gel, intermediate
          for blasting
          explosives.
    D    Ammonium nitrate-         1.5D  NA0331                 II  1.5D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          fuel oil mixture
          containing only
          prilled ammonium
          nitrate and fuel
          oil.
         Ammonium nitrate,          5.1  UN2426              .....  5.1.......                   B5, T7  None..........  None......  243......   Forbidden   Forbidden  D                 59, 60
          liquid (hot
          concentrated
          solution).
         Ammonium nitrate,         1.1D  UN0222                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          with more than 0.2
          percent
          combustible
          substances,
          including any
          organic substance
          calculated as
          carbon, to the
          exclusion of any
          other added
          substance.
         Ammonium nitrate,          5.1  UN1942                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            48, 59, 60,
          with not more than                                                                       TP33                                                                                      116
          0.2% total
          combustible
          material,
          including any
          organic substance,
          calculated as
          carbon to the
          exclusion of any
          other added
          substance.
         Ammonium nitrite...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ammonium                  1.1D  UN0402                 II  1.1D......                      107  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          perchlorate.
         Ammonium                   5.1  UN1442                 II  5.1.......   107, A9, IB6, IP2, T3,  152...........  212.......  242......        5 kg       25 kg  E                 58, 69
          perchlorate.                                                                             TP33
         Ammonium             Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          permanganate.
         Ammonium persulfate        5.1  UN1444                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            ...........
                                                                                                   TP33
         Ammonium picrate,         1.1D  UN0004                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10               5E, 19E
          dry or wetted with
          less than 10
          percent water, by
          mass.

[[Page 150]]

 
         Ammonium picrate,          4.1  UN1310                  I  4.1.......              23, A2, N41  None..........  211.......  None.....      0.5 kg      0.5 kg  D                 28, 36
          wetted with not
          less than 10
          percent water, by
          mass.
         Ammonium                     8  UN2818                 II  8, 6.1....       IB2, T7, TP2, TP13  154...........  202.......  243......         1 L        30 L  B             12, 40, 52
          polysulfide,
          solution.
         ...................  .........  ..................    III  8, 6.1....       IB3, T4, TP1, TP13  154...........  203.......  241......         5 L        60 L  B             12, 40, 52
         Ammonium                   6.1  UN2861                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                44, 89,
          polyvanadate.                                                                                                                                                                 100, 141
         Ammonium             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          silicofluoride,
          see Ammonium
          fluorosilicate.
         Ammonium sulfide             8  UN2683                 II  8, 6.1, 3.       IB1, T7, TP2, TP13  154...........  202.......  243......         1 L        30 L  B            12, 22, 52,
          solution.                                                                                                                                                                          100
         Ammunition, blank,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Cartridges for
          weapons, blank.
         Ammunition,               1.2G  UN0171                 II  1.2G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          illuminating with
          or without
          burster, expelling
          charge or
          propelling charge.
         Ammunition,               1.3G  UN0254                 II  1.3G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          illuminating with
          or without
          burster, expelling
          charge or
          propelling charge.
         Ammunition,               1.4G  UN0297                 II  1.4G......  .......................  ..............  62........  62.......   Forbidden       75 kg  02           ...........
          illuminating with
          or without
          burster, expelling
          charge or
          propelling charge.
         Ammunition,               1.3J  UN0247                 II  1.3J......  .......................  ..............  62........  None.....   Forbidden   Forbidden  04                   23E
          incendiary liquid
          or gel, with
          burster, expelling
          charge or
          propelling charge.
         Ammunition,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          incendiary (water-
          activated
          contrivances) with
          burster, expelling
          charge or
          propelling charge,
          see Contrivances,
          water-activated,
          etc..
         Ammunition,               1.2H  UN0243                 II  1.2H......  .......................  ..............  62........  62.......   Forbidden   Forbidden  08              8E, 14E,
          incendiary, white                                                                                                                                                             15E, 17E
          phosphorus, with
          burster, expelling
          charge or
          propelling charge.

[[Page 151]]

 
         Ammunition,               1.3H  UN0244                 II  1.3H......  .......................  ..............  62........  62.......   Forbidden   Forbidden  08              8E, 14E,
          incendiary, white                                                                                                                                                             15E, 17E
          phosphorus, with
          burster, expelling
          charge or
          propelling charge.
         Ammunition,               1.2G  UN0009                 II  1.2G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          incendiary with or
          without burster,
          expelling charge,
          or propelling
          charge.
         Ammunition,               1.3G  UN0010                 II  1.3G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          incendiary with or
          without burster,
          expelling charge,
          or propelling
          charge.
         Ammunition,               1.4G  UN0300                 II  1.4G......  .......................  ..............  62........  62.......   Forbidden       75 kg  02           ...........
          incendiary with or
          without burster,
          expelling charge
          or propelling
          charge.
         Ammunition,               1.4G  UN0362                 II  1.4G......  .......................  ..............  62........  62.......   Forbidden       75 kg  02           ...........
          practice.
         Ammunition,               1.3G  UN0488                 II  1.3G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          practice.
         Ammunition, proof..       1.4G  UN0363                 II  1.4G......  .......................  ..............  62........  62.......   Forbidden       75 kg  02           ...........
         Ammunition, rocket,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Warheads,
          rocket etc.
         Ammunition, SA       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (small arms), see
          Cartridges for
          weapons, etc.
         Ammunition, smoke    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (water-activated
          contrivances),
          white phosphorus,
          with burster,
          expelling charge
          or propelling
          charge, see
          Contrivances,
          water-activated,
          etc. (UN 0248).
         Ammunition, smoke    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (water-activated
          contrivances),
          without white
          phosphorus or
          phosphides, with
          burster, expelling
          charge or
          propelling charge,
          see Contrivances,
          water-activated,
          etc. (UN 0249).
         Ammunition smoke,         1.2H  UN0245                 II  1.2H......  .......................  ..............  62........  62.......   Forbidden   Forbidden  08              8E, 14E,
          white phosphorus                                                                                                                                                              15E, 17E
          with
          burster,expelling
          charge, or
          propelling charge.
         Ammunition, smoke,        1.3H  UN0246                 II  1.3H......  .......................  ..............  62........  62.......   Forbidden   Forbidden  08              8E, 14E,
          white phosphorus                                                                                                                                                              15E, 17E
          with burster,
          expelling charge,
          or propelling
          charge.
         Ammunition, smoke         1.2G  UN0015                 II  1.2G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  ...........     8E, 17E,
          with or without                                                                                                                                                                    20E
          burster, expelling
          charge or
          propelling charge.
         Ammunition, smoke         1.3G  UN0016                 II  1.3G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  ...........     8E, 17E,
          with or without                                                                                                                                                                    20E
          burster, expelling
          charge or
          propelling charge.

[[Page 152]]

 
         Ammunition, smoke         1.4G  UN0303                 II  1.4G......  .......................  ..............  62........  62.......   Forbidden       75 kg  ...........      7E, 8E,
          with or without                                                                                                                                                              14E, 15E,
          burster, expelling                                                                                                                                                                 17E
          charge or
          propelling charge.
         Ammunition,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          sporting, see
          Cartridges for
          weapons, etc. (UN
          0012; UN 0328; UN
          0339).
         Ammunition, tear-          6.1  UN2017                 II  6.1, 8....  .......................  None..........  212.......  None.....   Forbidden       50 kg  E                 13, 40
          producing, non-
          explosive, without
          burster or
          expelling charge,
          non-fuzed.
         Ammunition, tear-         1.2G  UN0018                 II  1.2G, 8,    .......................  ..............  62........  62.......   Forbidden   Forbidden  ...........     8E, 17E,
          producing with                                             6.1.                                                                                                                    20E
          burster, expelling
          charge or
          propelling charge.
         Ammunition, tear-         1.3G  UN0019                 II  1.3G, 8,    .......................  ..............  62........  62.......   Forbidden   Forbidden  ...........     8E, 17E,
          producing with                                             6.1.                                                                                                                    20E
          burster, expelling
          charge or
          propelling charge.
         Ammunition, tear-         1.4G  UN0301                 II  1.4G, 8,    .......................  ..............  62........  62.......   Forbidden       75 kg  ...........      7E, 8E,
          producing with                                             6.1.                                                                                                              14E, 15E,
          burster, expelling                                                                                                                                                                 17E
          charge or
          propelling charge.
         Ammunition, toxic,         6.1  UN2016                 II  6.1.......  .......................  None..........  212.......  None.....   Forbidden      100 kg  E                 13, 40
          non-explosive,
          without burster or
          expelling charge,
          non-fuzed.
         Ammunition, toxic    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (water-activated
          contrivances),
          with burster,
          expelling charge
          or propelling
          charge, see
          Contrivances,
          water-activated,
          etc.
    G    Ammunition, toxic         1.2K  UN0020                 II  1.2K, 6.1.  .......................  ..............  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          with burster,                                                                                                                                                                 15E, 17E
          expelling charge,
          or propelling
          charge.
    G    Ammunition, toxic         1.3K  UN0021                 II  1.3K, 6.1.  .......................  ..............  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          with burster,                                                                                                                                                                 15E, 17E
          expelling charge,
          or propelling
          charge.
         Amyl acetates......          3  UN1104                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Amyl acid phosphate          8  UN2819                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Amyl butyrates.....          3  UN2620                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Amyl chlorides.....          3  UN1107                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Amyl formates......          3  UN1109                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........

[[Page 153]]

 
         Amyl mercaptans....          3  UN1111                 II  3.........     A3, A6, IB2, T4, TP1  None..........  202.......  242......         5 L        60 L  B                95, 102
         n-Amyl methyl                3  UN1110                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          ketone.
         Amyl nitrate.......          3  UN1112                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                     40
         Amyl nitrites......          3  UN1113                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E                     40
         Amylamines.........          3  UN1106                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B            ...........
         ...................  .........  ..................    III  3, 8......         B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A            ...........
         Amyltrichlorosilane          8  UN1728                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
                                                                                         TP2, TP7, TP13
         Anhydrous ammonia,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ammonia,
          anhydrous.
         Anhydrous            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydrofluoric acid,
          see Hydrogen
          fluoride,
          anhydrous.
    +    Aniline............        6.1  UN1547                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                 40, 52
         Aniline                    6.1  UN1548                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          hydrochloride.
         Aniline oil, see     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Aniline.
         Anisidines.........        6.1  UN2431                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Anisole............          3  UN2222                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Anisoyl chloride...          8  UN1729                 II  8.........   B2, B4, IB8, IP2, IP4,  154...........  212.......  240......       15 kg       50 kg  A            ...........
                                                                                               T3, TP33
         Anti-freeze,         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          liquid, see
          Flammable liquids,
          n.o.s..
         Antimonous           .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          chloride, see
          Antimony
          trichloride.
    G    Antimony compounds,        6.1  UN3141                III  6.1.......   35, IB3, T7, TP1, TP28  153...........  203.......  241......        60 L       220 L  A
          inorganic, liquid,
          n.o.s.
    G    Antimony compounds,        6.1  UN1549                III  6.1.......   35, IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A
          inorganic, solid,
          n.o.s.
         Antimony lactate...        6.1  UN1550                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Antimony                     8  UN1730                 II  8.........         B2, IB2, T7, TP2  None..........  202.......  242......         1 L        30 L  C                     40
          pentachloride,
          liquid.
         Antimony                     8  UN1731                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  C                     40
          pentachloride,
          solutions.
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  C                     40
         Antimony                     8  UN1732                 II  8, 6.1....    A3, A6, A7, A10, IB2,  None..........  202.......  243......   Forbidden        30 L  D                44, 89,
          pentafluoride.                                                               N3, N36, T7, TP2                                                                                 100, 141
         Antimony potassium         6.1  UN1551                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          tartrate.
         Antimony powder....        6.1  UN2871                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Antimony sulfide     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          and a chlorate,
          mixtures of.
         Antimony sulfide,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solid, see
          Antimony
          compounds,
          inorganic, n.o.s..
         Antimony                     8  UN1733                 II  8.........                  B2, IB2  154...........  202.......  242......         1 L        30 L  C                     40
          trichloride,
          liquid.
         Antimony                     8  UN1733                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                    40.
          trichloride, solid.
         Aqua ammonia, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Ammonia solution,
          etc.
         Argon, compressed..        2.2  UN1006              .....  2.2.......  .......................  306, 307......  302.......  314, 315.       75 kg      150 kg  A
         Argon, refrigerated        2.2  UN1951              .....  2.2.......                 T75, TP5  320...........  316.......  318......       50 kg      500 kg  D
          liquid (cryogenic
          liquid).

[[Page 154]]

 
         Arsenic............        6.1  UN1558                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Arsenic acid,              6.1  UN1553                  I  6.1.......      T20, TP2, TP7, TP13  None..........  201.......  243......         1 L        30 L  B                     46
          liquid.
         Arsenic acid, solid        6.1  UN1554                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Arsenic bromide....        6.1  UN1555                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                 12, 40
         Arsenic chloride,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Arsenic
          trichloride.
    G    Arsenic compounds,         6.1  UN1556                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                40, 137
          liquid, n.o.s.
          inorganic,
          including
          arsenates, n.o.s.;
          arsenites, n.o.s.;
          arsenic sulfides,
          n.o.s.; and
          organic compounds
          of arsenic, n.o.s.
                              .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                40, 137
                                                                                                   TP27
                              .........  ..................    III  6.1.......       IB3, T7, TP2, TP28  153...........  203.......  241......        60 L       220 L  B                40, 137
    G    Arsenic compounds,         6.1  UN1557                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                    137
          solid, n.o.s.
          inorganic,
          including
          arsenates, n.o.s.;
          arsenites, n.o.s.;
          arsenic sulfides,
          n.o.s.; and
          organic compounds
          of arsenic, n.o.s.
                              .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                    137
                              .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                    137
         Arsenic pentoxide..        6.1  UN1559                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Arsenic sulfide and  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          a chlorate,
          mixtures of.
         Arsenic trichloride        6.1  UN1560                  I  6.1.......    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  B                     40
                                                                                  TP2, TP13, TP38, TP45
         Arsenic trioxide...        6.1  UN1561                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Arsenic, white,      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solid, see Arsenic
          trioxide.
         Arsenical dust.....        6.1  UN1562                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Arsenical                    3  UN2760                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  B                     40
          pesticides,
          liquid, flammable,
          toxic, flash point
          less than 23
          degrees C.
         ...................  .........  ..................     II  3, 6.1....     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L        60 L  B                     40
                                                                                                   TP27
         Arsenical                  6.1  UN2994                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic.

[[Page 155]]

 
         ...................  .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP2, TP28  153...........  203.......  241......        60 L       220 L  A                     40
         Arsenical                  6.1  UN2993                  I  6.1, 3....     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic,
          flammable, flash
          point not less
          than 23 degrees C.
         ...................  .........  ..................     II  6.1, 3....     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1, 3....   B1, IB3, T7, TP2, TP28  153...........  203.......  242......        60 L       220 L  A                     40
         Arsenical                  6.1  UN2759                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          pesticides, solid,
          toxic.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40
         Arsenious acid,      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solid, see Arsenic
          trioxide.
         Arsenious and        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mercuric iodide
          solution, see
          Arsenic compounds,
          liquid, n.o.s..
         Arsine.............        2.3  UN2188              .....  2.3, 2.1..                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
         Articles,                 1.6N  UN0486                 II  1.6N......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive,
          extremely
          insensitive or
          Articles, EEI.
    G    Articles,                 1.4S  UN0349                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05
          explosive, n.o.s.
    G    Articles,                 1.4B  UN0350                 II  1.4B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  06
          explosive, n.o.s.
    G    Articles,                 1.4C  UN0351                 II  1.4C......  .......................  None..........  62........  None.....   Forbidden       75 kg  06
          explosive, n.o.s.
    G    Articles,                 1.4D  UN0352                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06
          explosive, n.o.s.
    G    Articles,                 1.4G  UN0353                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06
          explosive, n.o.s.
    G    Articles,                 1.1L  UN0354                 II  1.1L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          explosive, n.o.s.                                                                                                                                                            15E, 17E.
    G    Articles,                 1.2L  UN0355                 II  1.2L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          explosive, n.o.s.                                                                                                                                                            15E, 17E.
    G    Articles,                 1.3L  UN0356                 II  1.3L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          explosive, n.o.s.                                                                                                                                                            15E, 17E.
    G    Articles,                 1.1C  UN0462                 II  1.1C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.1D  UN0463                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.1E  UN0464                 II  1.1E......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.1F  UN0465                 II  1.1F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08
          explosive, n.o.s.
    G    Articles,                 1.2C  UN0466                 II  1.2C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.2D  UN0467                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07.
          explosive, n.o.s.
    G    Articles,                 1.2E  UN0468                 II  1.2E......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.2F  UN0469                 II  1.2F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08
          explosive, n.o.s.
    G    Articles,                 1.3C  UN0470                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          explosive, n.o.s.
    G    Articles,                 1.4E  UN0471                 II  1.4E......  .......................  None..........  62........  None.....   Forbidden       75 kg  06
          explosive, n.o.s.
    G    Articles,                 1.4F  UN0472                 II  1.4F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08
          explosive, n.o.s.
         Articles,                  2.2  UN3164              .....  2.2.......  .......................  306...........  302, 304..  None.....    No limit    No limit  A            ...........
          pressurized
          pneumatic or
          hydraulic
          containing non-
          flammable gas.
         Articles,                 1.2L  UN0380                 II  1.2L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          pyrophoric.                                                                                                                                                                   15E, 17E
         Articles,                 1.1G  UN0428                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          pyrotechnic for
          technical purposes.

[[Page 156]]

 
         Articles,                 1.2G  UN0429                 II  1.2G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          pyrotechnic for
          technical purposes.
         Articles,                 1.3G  UN0430                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          pyrotechnic for
          technical purposes.
         Articles,                 1.4G  UN0431                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          pyrotechnic for
          technical purposes.
         Articles,                 1.4S  UN0432                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
          pyrotechnic for
          technical purposes.
    D    Asbestos...........          9  NA2212                III  9.........       156, IB8, IP2, IP4  155...........  216.......  240......      200 kg      200 kg  A                 34, 40
         Ascaridole (organic  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxide).
    D    Asphalt, at or               3  NA1999                III  3.........             IB3, T1, TP3  150...........  203.......  247......   Forbidden   Forbidden  D            ...........
          above its flash
          point.
    D    Asphalt, cut back,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Tars, liquid,
          etc.
         Automobile,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          motorcycle,
          tractor, other
          self-propelled
          vehicle, engine,
          or other
          mechanical
          apparatus, see
          Vehicles or
          Battery etc.
  A G    Aviation regulated           9  UN3334              .....  9.........                      A35  155...........  204.......  .........    No limit    No limit  A            ...........
          liquid, n.o.s..
  A G    Aviation regulated           9  UN3335              .....  9.........                      A35  155...........  204.......  .........    No limit    No limit  A            ...........
          solid, n.o.s..
         Azaurolic acid       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (salt of) (dry).
         Azido guanidine      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          picrate (dry).
         5-Azido-1-hydroxy    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tetrazole.
         Azido hydroxy        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tetrazole (mercury
          and silver salts).
         3-Azido-1,2-         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Propylene glycol
          dinitrate.
         Azidodithiocarbonic  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          acid.
         Azidoethyl nitrate.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         1-                   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Aziridinylphosphin
          e oxide-(tris),
          see Tris-(1-
          aziridinyl)
          phosphine oxide,
          solution.
         Azodicarbonamide...        4.1  UN3242                 II  4.1.......        38, IB8, T3, TP33  151...........  223.......  240......   Forbidden   Forbidden  D             2, 52, 53,
                                                                                                                                                                                              74
         Azotetrazole (dry).  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Barium.............        4.3  UN1400                 II  4.3.......  A19, IB7, IP2, T3, TP33  151...........  212.......  241......       15 kg       50 kg  E                     52
         Barium alloys,             4.2  UN1854                  I  4.2.......           T21, TP7, TP33  None..........  181.......  None.....   Forbidden   Forbidden  D            ...........
          pyrophoric.

[[Page 157]]

 
         Barium azide, dry         1.1A  UN0224                 II  1.1A, 6.1.                 111, 117  None..........  62........  None.....   Forbidden   Forbidden  12           ...........
          or wetted with
          less than 50
          percent water, by
          mass.
         Barium azide,              4.1  UN1571                  I  4.1, 6.1..                  162, A2  None..........  182.......  None.....   Forbidden      0.5 kg  D                     28
          wetted with not
          less than 50
          percent water, by
          mass.
         Barium bromate.....        5.1  UN2719                 II  5.1, 6.1..  IB8, IP2, IP4, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
         Barium chlorate,           5.1  UN1445                 II  5.1, 6.1..   A9, IB6, IP2, N34, T3,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
          solid.                                                                                   TP33
         Barium chlorate,           5.1  UN3405                 II  5.1, 6.1..    A9, IB2, N34, T4, TP1  152...........  202.......  243......         1 L         5 L  A            56, 58, 133
          solution.
         ...................  .........  ..................    III  5.1, 6.1..    A9, IB2, N34, T4, TP1  152...........  203.......  242......       2.5 L        30 L  A            56, 58, 133
    G    Barium compounds,          6.1  UN1564                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A
          n.o.s.
                              .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Barium cyanide.....        6.1  UN1565                  I  6.1.......  IB7, IP1, N74, N75, T6,  None..........  211.......  242......        5 kg       50 kg  A                 40, 52
                                                                                                   TP33
         Barium hypochlorite        5.1  UN2741                 II  5.1, 6.1..   A7, A9, IB8, IP2, IP4,  152...........  212.......  None.....        5 kg       25 kg  B             4, 52, 56,
          with more than 22                                                               N34, T3, TP33                                                                                  58, 106
          percent available
          chlorine.
         Barium nitrate.....        5.1  UN1446                 II  5.1, 6.1..  IB8, IP2, IP4, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A            ...........
         Barium oxide.......        6.1  UN1884                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Barium perchlorate,        5.1  UN1447                 II  5.1, 6.1..       IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
          solid.
         Barium perchlorate,        5.1  UN3406                 II  5.1, 6.1..             IB2, T4, TP1  152...........  202.......  243......         1 L         5 L  A            56, 58, 133
          solution.
         ...................  .........  ..................    III  5.1, 6.1..             IB2, T4, TP1  152...........  203.......  242......       2.5 L        30 L  A            56, 58, 133
         Barium permanganate        5.1  UN1448                 II  5.1, 6.1..       IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  D            56, 58, 138
         Barium peroxide....        5.1  UN1449                 II  5.1, 6.1..   A9, IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A            13, 52, 56,
                                                                                                                                                                                              75
         Barium selenate,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Selenates or
          Selenites.
         Barium selenite,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Selenates or
          Selenites.
         Batteries,                 4.3  UN3292                 II  4.3.......  .......................  189...........  189.......  189......   Forbidden    No limit  A            ...........
          containing sodium.
         Batteries, dry,              8  UN3028                III  8.........                      237  None..........  213.......  None.....       25 kg      230 kg  A                     52
          containing                                                                                                                                 gross       gross
          potassium
          hydroxide solid,
          electric, storage.
         Batteries, dry,      .........  ..................  .....  ..........                      130
          sealed, n.o.s..
    W    Batteries, nickel-           9  UN3496              .....  9.........                      340  ..............  ..........  .........  ..........  ..........  A                     48
          metal hydride see
          Batteries, dry,
          sealed, n.o.s. for
          nickel-metal
          hydride batteries
          transported by
          modes other than
          vessel.

[[Page 158]]

 
         Batteries, wet,              8  UN2794                III  8.........  .......................  159...........  159.......  159......       30 kg    No limit  A                    146
          filled with acid,                                                                                                                          gross
          electric storage.
         Batteries, wet,              8  UN2795                III  8.........  .......................  159...........  159.......  159......       30 kg    No limit  A                52, 146
          filled with                                                                                                                                gross
          alkali, electric
          storage.
         Batteries, wet, non-         8  UN2800                III  8.........  .......................  159a..........  159.......  159......    No limit    No limit  A
          spillable,
          electric storage.
         Battery fluid, acid          8  UN2796                 II  8.........    A3, A7, B2, B15, IB2,  154...........  202.......  242......         1 L        30 L  B            ...........
                                                                                       N6, N34, T8, TP2
         Battery fluid,               8  UN2797                 II  8.........    B2, IB2, N6, T7, TP2,  154...........  202.......  242......         1 L        30 L  A                     29
          alkali.                                                                                  TP28
         Battery lithium      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          type, see Lithium
          batteries etc.
         Battery-powered              9  UN3171              .....  9.........                      134  220...........  220.......  None.....    No limit    No limit  A            ...........
          vehicle or Battery-
          powered equipment.
         Battery, wet,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          filled with acid
          or alkali with
          vehicle or
          mechanical
          equipment
          containing an
          internal
          combustion engine,
          see Vehicle, etc.
          or Engines,
          internal
          combustion, etc.
    +    Benzaldehyde.......          9  UN1990                III  9.........             IB3, T2, TP1  155...........  203.......  241......       100 L       220 L  A            ...........
         Benzene............          3  UN1114                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Benzene diazonium    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          chloride (dry).
         Benzene diazonium    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrate (dry).
         Benzene phosphorus   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dichloride, see
          Phenyl phosphorus
          dichloride.
         Benzene phosphorus   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          thiodichloride,
          see Phenyl
          phosphorus
          thiodichloride.
         Benzene sulfonyl             8  UN2225                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                     40
          chloride.
         Benzene triozonide.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Benzenethiol, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Phenyl mercaptan.
         Benzidine..........        6.1  UN1885                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Benzol, see Benzene  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Benzonitrile.......        6.1  UN2224                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                 40, 52

[[Page 159]]

 
         Benzoquinone.......        6.1  UN2587                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Benzotrichloride...          8  UN2226                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                     40
         Benzotrifluoride...          3  UN2338                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Benzoxidiazoles      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (dry).
         Benzoyl azide......  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Benzoyl chloride...          8  UN1736                 II  8.........   B2, IB2, T8, TP2, TP13  154...........  202.......  242......         1 L        30 L  C                     40
         Benzyl bromide.....        6.1  UN1737                 II  6.1, 8....   A3, A7, IB2, N33, N34,  None..........  202.......  243......         1 L        30 L  D                13, 40.
                                                                                          T8, TP2, TP13
         Benzyl chloride....        6.1  UN1738                 II  6.1, 8....   A3, A7, B70, IB2, N33,  None..........  202.......  243......         1 L        30 L  D                13, 40.
                                                                                     N42, T8, TP2, TP13
         Benzyl chloride            6.1  UN1738                 II  6.1, 8....    A3, A7, B8, B11, IB2,  153...........  202.......  243......         1 L        30 L  D                 13, 40
          unstabilized.                                                         N33, N34, N43, T8, TP2,
                                                                                                   TP13
         Benzyl                       8  UN1739                  I  8.........    A3, A6, B4, N41, T10,  None..........  201.......  243......   Forbidden       2.5 L  D                     40
          chloroformate.                                                                      TP2, TP13
         Benzyl iodide......        6.1  UN2653                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B                 12, 40
         Benzyldimethylamine          8  UN2619                 II  8, 3......         B2, IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  A                 40, 48
         Benzylidene                6.1  UN1886                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  D                     40
          chloride.
    G    Beryllium                  6.1  UN1566                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A
          compounds, n.o.s.
                              .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A
         Beryllium nitrate..        5.1  UN2464                 II  5.1, 6.1..  IB8, IP2, IP4, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A            ...........
         Beryllium, powder..        6.1  UN1567                 II  6.1, 4.1..  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       15 kg       50 kg  A            ...........
         Bicyclo [2,2,1]              3  UN2251                 II  3.........             IB2, T7, TP2  150...........  202.......  242......         5 L        60 L  D            ...........
          hepta-2,5-diene,
          stabilized or 2,5-
          Norbornadiene,
          stabilized.
         Biological                 6.2  UN3373              .....  ..........                      A82  134...........  199.......  None.....    4 L or 4    4 L or 4  A                     40
          substance,                                                                                                                                    kg          kg
          Category B.
         Biphenyl triozonide  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Bipyridilium                 3  UN2782                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  E            ...........
          pesticides,
          liquid, flammable,
          toxic, flash point
          less than 23
          degrees C.
         ...................  .........  ..................     II  3, 6.1....     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L        60 L  B                     40
                                                                                                   TP27
         Bipyridilium               6.1  UN3016                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic.
         ...................  .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP2, TP28  153...........  203.......  241......        60 L       220 L  A                     40
         Bipyridilium               6.1  UN3015                  I  6.1, 3....     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                 21, 40
          pesticides,
          liquid, toxic,
          flammable, flash
          point not less
          than 23 degrees C.
         ...................  .........  ..................     II  6.1, 3....     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                 21, 40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1, 3....   B1, IB3, T7, TP2, TP28  153...........  203.......  242......        60 L       220 L  A                 21, 40
         Bipyridilium               6.1  UN2781                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          pesticides, solid,
          toxic.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40

[[Page 160]]

 
         Bis (Aminopropyl)    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          piperazine, see
          Corrosive liquid,
          n.o.s..
         Bisulfate, aqueous           8  UN2837                 II  8.........    A7, B2, IB2, N34, T7,  154...........  202.......  242......         1 L        30 L  A            ...........
          solution.                                                                                 TP2
         ...................  .........  ..................    III  8.........    A7, IB3, N34, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Bisulfites, aqueous          8  UN2693                III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                 40, 52
          solutions, n.o.s..
         Black powder,             1.1D  UN0028                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          compressed or
          Gunpowder,
          compressed or
          Black powder, in
          pellets or
          Gunpowder, in
          pellets.
         Black powder or           1.1D  UN0027                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          Gunpowder,
          granular or as a
          meal.
    D    Black powder for           4.1  NA0027                  I  4.1.......                       70  None..........  170.......  None.....   Forbidden   Forbidden  E            ...........
          small arms.
         Blasting agent,      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          n.o.s., see
          Explosives,
          blasting etc.
         Blasting cap         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          assemblies, see
          Detonator
          assemblies, non-
          electric, for
          blasting.
         Blasting caps,       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          electric, see
          Detonators,
          electric for
          blasting.
         Blasting caps, non-  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          electric, see
          Detonators, non-
          electric, for
          blasting.
         Bleaching powder,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Calcium
          hypochlorite
          mixtures, etc.
    I    Blue asbestos                9  UN2212                 II  9.........  156, IB8, IP2, IP4, T3,  155...........  216.......  240......   Forbidden   Forbidden  A                 34, 40
          (Crocidolite) or                                                                         TP33
          Brown asbestos
          (amosite,
          mysorite).
         Bombs, photo-flash.       1.1F  UN0037                 II  1.1F......  .......................  ..............  62........  None.....   Forbidden   Forbidden  08           ...........
         Bombs, photo-flash.       1.1D  UN0038                 II  1.1D......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
         Bombs, photo-flash.       1.2G  UN0039                 II  1.2G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
         Bombs, photo-flash.       1.3G  UN0299                 II  1.3G......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
         Bombs, smoke, non-           8  UN2028                 II  8.........  .......................  None..........  160.......  None.....   Forbidden       50 kg  E                     40
          explosive, with
          corrosive liquid,
          without initiating
          device.
         Bombs, with               1.1F  UN0033                 II  1.1F......  .......................  ..............  62........  None.....   Forbidden   Forbidden  08           ...........
          bursting charge.
         Bombs, with               1.1D  UN0034                 II  1.1D......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          bursting charge.

[[Page 161]]

 
         Bombs, with               1.2D  UN0035                 II  1.2D......  .......................  ..............  62........  62.......   Forbidden   Forbidden  03           ...........
          bursting charge.
         Bombs, with               1.2F  UN0291                 II  1.2F......  .......................  ..............  62........  None.....   Forbidden   Forbidden  08           ...........
          bursting charge.
         Bombs with                1.1J  UN0399                 II  1.1J......  .......................  ..............  62........  None.....   Forbidden   Forbidden  04                   23E
          flammable liquid,
          with bursting
          charge.
         Bombs with                1.2J  UN0400                 II  1.2J......  .......................  ..............  62........  None.....   Forbidden   Forbidden  04                   23E
          flammable liquid,
          with bursting
          charge.
         Boosters with             1.1B  UN0225                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
          detonator.
         Boosters with             1.2B  UN0268                 II  1.2B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          detonator.
         Boosters, without         1.1D  UN0042                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          detonator.
         Boosters, without         1.2D  UN0283                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          detonator.
         Borate and chlorate  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures, see
          Chlorate and
          borate mixtures.
         Borneol............        4.1  UN1312                III  4.1.......   A1, IB8, IP3, T1, TP33  None..........  213.......  240......       25 kg      100 kg  A            ...........
    +    Boron tribromide...          8  UN2692                  I  8, 6.1....    2, B9, B14, B32, N34,  None..........  227.......  244......   Forbidden   Forbidden  C                     12
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Boron trichloride..        2.3  UN1741              .....  2.3, 8....               3, B9, B14  None..........  304.......  314......   Forbidden   Forbidden  D                 25, 40
         Boron trifluoride..        2.3  UN1008              .....  2.3, 8....               2, B9, B14  None..........  302.......  314, 315.   Forbidden   Forbidden  D                     40
         Boron trifluoride            8  UN1742                 II  8.........     B2, B6, IB2, T8, TP2  154...........  202.......  242......         1 L        30 L  A            ...........
          acetic acid
          complex, liquid.
         Boron trifluoride            8  UN3419                 II  8.........   B2, B6, IB8, IP2, IP4,  154...........  212.......  240......       15 kg       50 kg  A            ...........
          acetic acid                                                                          T3, TP33
          complex, solid.
         Boron trifluoride            8  UN2604                  I  8, 3......        A3, A19, T10, TP2  None..........  201.......  243......       0.5 L       2.5 L  D                     40
          diethyl etherate.
         Boron trifluoride            8  UN2851                 II  8.........             IB2, T7, TP2  154...........  212.......  240......       15 kg       50 kg  B                12, 40,
          dihydrate.
         Boron trifluoride          4.3  UN2965                  I  4.3, 8, 3.       A19, T10, TP2, TP7  None..........  201.......  243......   Forbidden         1 L  D            21, 28, 40,
          dimethyl etherate.                                                                                                                                                             49, 100
         Boron trifluoride            8  UN1743                 II  8.........         B2, IB2, T8, TP2  154...........  202.......  242......         1 L        30 L  A            ...........
          propionic acid
          complex, liquid.
         Boron trifluoride            8  UN3420                 II  8.........   B2, IB8, IP2, IP4, T3,  154...........  212.......  240......       15 kg       50 kg  A            ...........
          propionic acid                                                                           TP33
          complex, solid.
         Box toe gum, see     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Nitrocellulose etc.
    G    Bromates,                  5.1  UN3213                 II  5.1.......        350, IB2, T4, TP1  152...........  202.......  242......         1 L         5 L  B            56, 58, 133
          inorganic, aqueous
          solution, n.o.s.
                              .........  ..................    III  5.1.......        350, IB2, T4, TP1  152...........  203.......  241......       2.5 L        30 L  B            56, 58, 133
    G    Bromates,                  5.1  UN1450                 II  5.1.......  350, IB8, IP2, IP4, T3,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
          inorganic, n.o.s.                                                                        TP33
    +    Bromine............          8  UN1744                  I  8, 6.1....    1, B9, B85, N34, N43,  None..........  226.......  249......   Forbidden   Forbidden  D            12, 40, 66,
                                                                                   T22, TP2, TP10, TP13                                                                               74, 89, 90
         Bromine azide......  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Bromine chloride...        2.3  UN2901              .....  2.3, 8,             2, B9, B14, N86  None..........  304.......  314, 315.   Forbidden   Forbidden  D             40, 89, 90
                                                                     5.1.
    +    Bromine                    5.1  UN1745                  I  5.1, 6.1,     1, B9, B14, B30, T22,  None..........  228.......  244......   Forbidden   Forbidden  D            25, 40, 66,
          pentafluoride.                                             8.           TP2, TP13, TP38, TP44                                                                                       90
    +    Bromine solutions..          8  UN1744                  I  8, 6.1....    1, B9, B85, N34, N43,  None..........  226.......  249......   Forbidden   Forbidden  D            12, 40, 66,
                                                                                   T22, TP2, TP10, TP13                                                                               74, 89, 90

[[Page 162]]

 
    +    Bromine solutions..          8  UN1744                  I  8, 6.1....    2, B9, B85, N34, N43,  None..........  227.......  249......   Forbidden   Forbidden  D            12, 40, 66,
                                                                                   T22, TP2, TP10, TP13                                                                               74, 89, 90
    +    Bromine trifluoride        5.1  UN1746                  I  5.1, 6.1,     2, B9, B14, B32, T22,  None..........  228.......  244......   Forbidden   Forbidden  D            25, 40, 66,
                                                                     8.           TP2, TP13, TP38, TP45                                                                                       90
         4-Bromo-1,2-         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrobenzene.
         4-Bromo-1,2-         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrobenzene
          (unstable at 59
          degrees C).
         1-Bromo-3-                 6.1  UN2688                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          chloropropane.
         1-Bromo-3-                   3  UN2341                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          methylbutane.
         1-Bromo-3-           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrobenzene
          (unstable at 56
          degrees C).
         2-Bromo-2-                 4.1  UN3241                III  4.1.......             46, IB8, IP3  151...........  213.......  None.....       25 kg       50 kg  C             12, 25, 40
          nitropropane-1,3-
          diol.
         Bromoacetic acid,            8  UN3425                 II  8.........  A7, IB8, IP2, IP4, N34,  154...........  212.......  240......       15 kg       50 kg  A            ...........
          solid.                                                                               T3, TP33
         Bromoacetic acid             8  UN1938                 II  8.........     A7, B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                     40
          solution.
         ...................  .........  ..................    III  8.........         B2, IB3, T7, TP2  154...........  203.......  241......         5 L        60 L  A                     40
    +    Bromoacetone.......        6.1  UN1569                 II  6.1, 3....        2, T20, TP2, TP13  None..........  193.......  245......   Forbidden   Forbidden  D                     40
         Bromoacetyl bromide          8  UN2513                 II  8.........         B2, IB2, T8, TP2  154...........  202.......  242......         1 L        30 L  C                 40, 53
         Bromobenzene.......          3  UN2514                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Bromobenzyl                6.1  UN1694                  I  6.1.......           T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  D             12, 40, 52
          cyanides, liquid.
         Bromobenzyl                6.1  UN3449                  I  6.1.......                 T6, TP33  None..........  211.......  242......        5 kg       50 kg  D             12, 40, 52
          cyanides, solid.
         1-Bromobutane......          3  UN1126                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         2-Bromobutane......          3  UN2339                 II  3.........         B1, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Bromochloromethane.        6.1  UN1887                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         2-Bromoethyl ethyl           3  UN2340                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
          ether.
         Bromoform..........        6.1  UN2515                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                 12, 40
         Bromomethylpropanes          3  UN2342                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         2-Bromopentane.....          3  UN2343                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Bromopropanes......          3  UN2344                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         ...................  .........  ..................    III  3.........             IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         3-Bromopropyne.....          3  UN2345                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  D                     40
         Bromosilane........  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Bromotoluene-alpha,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Benzyl bromide.
         Bromotrifluoroethyl        2.1  UN2419              .....  2.1.......  .......................  None..........  304.......  314, 315.   Forbidden      150 kg  B                     40
          ene.

[[Page 163]]

 
         Bromotrifluorometha        2.2  UN1009              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ne or Refrigerant
          gas, R 13B1..
         Brucine............        6.1  UN1570                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A            ...........
         Bursters, explosive       1.1D  UN0043                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Butadienes,                2.1  UN1010              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  B                     40
          stabilized or
          Butadienes and
          Hydrocarbon
          mixture,
          stabilized
          containing more
          than 40%
          butadienes.
         Butane see also            2.1  UN1011              .....  2.1.......                  19, T50  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
          Petroleum gases,
          liquefied.
         Butane, butane       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures and
          mixtures having
          similar properties
          in cartridges each
          not exceeding 500
          grams, see
          Receptacles, etc.
         Butanedione........          3  UN2346                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         1,2,4-Butanetriol    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trinitrate.
         Butanols...........          3  UN1120                 II  3.........       IB2, T4, TP1, TP29  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         tert-Butoxycarbonyl  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          azide.
         Butyl acetates.....          3  UN1123                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Butyl acid                   8  UN1718                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          phosphate.
         Butyl acrylates,             3  UN2348                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          stabilized.
         Butyl alcohols, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Butanols.
         Butyl benzenes.....          3  UN2709                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         n-Butyl bromide,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see 1-Bromobutane.
         n-Butyl chloride,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Chlorobutanes.
         n-Butyl                    6.1  UN2743                  I  6.1, 8, 3.    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  A            12, 13, 21,
          chloroformate.                                                          TP2, TP13, TP38, TP45                                                                              25, 40, 100
         Butyl ethers, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Dibutyl ethers.
         Butyl ethyl ether,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ethyl butyl
          ether.
         n-Butyl formate....          3  UN1128                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         tert-Butyl           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydroperoxide,
          with more than 90
          percent with water.
         tert-Butyl                 4.2  UN3255                  I  4.2, 8....  .......................  None..........  211.......  243......   Forbidden   Forbidden  D            ...........
          hypochlorite.
         N-n-Butyl imidazole        6.1  UN2690                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
         tert-Butyl                 6.1  UN2484                  I  6.1, 3....    1, B9, B14, B30, B72,  None..........  226.......  244......   Forbidden   Forbidden  D                     40
          isocyanate.                                                             T20, TP2, TP13, TP38,
                                                                                                   TP44
         n-Butyl isocyanate.        6.1  UN2485                  I  6.1, 3....    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Butyl mercaptans...          3  UN2347                 II  3.........     A3, A6, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  D                 52, 95
         n-Butyl                      3  UN2227                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          methacrylate,
          stabilized.
         Butyl methyl ether.          3  UN2350                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........


[[Page 164]]


                                                                            Sec.  172.101 Hazardous Materials Table
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                                                          (8)                             (9)             (10)  Vessel  stowage
                                                                                                        ----------------------------------------------------------------------------------------
                                                                                                              Packaging  (Sec.  173.***)        Quantity limitations
         Hazardous materials    Hazard                                                                  ---------------------------------------     (see Sec. Sec.
Symbols    descriptions and    class or    Identification      PG      Label       Special provisions                                             173.27 and 175.75)
           proper shipping     Division        Numbers                 Codes        (Sec.  172.102)                                           ------------------------   Location      Other
                names                                                                                      Exceptions     Non-bulk      Bulk     Passenger     Cargo
                                                                                                                                                 aircraft/   aircraft
                                                                                                                                                   rail        only
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
(1)      (2)................        (3)  (4)                   (5)  (6).......                      (7)  (8A)..........  (8B)......  (8C).....        (9A)        (9B)  (10A)              (10B)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
 
         Butyl nitrites.....          3  UN2351                  I  3.........      T11, TP1, TP8, TP27  150...........  201.......  243......         1 L        30 L  E                     40
         ...................  .........  ..................     II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                     40
         tert-Butyl           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxyacetate,
          with more than 76
          percent in
          solution.
         n-Butyl              Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxydicarbonate,
          with more than 52
          percent in
          solution.
         tert-Butyl           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxyisobutyrate,
          with more than 77
          percent in
          solution.
         Butyl phosphoric     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          acid, see Butyl
          acid phosphate.
         Butyl propionates..          3  UN1914                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         5-tert-Butyl-2,4,6-        4.1  UN2956                III  4.1.......                      159  None..........  223.......  None.....   Forbidden   Forbidden  D            12, 25, 48,
          trinitro-m-xylene                                                                                                                                                                  127
          or Musk xylene.
         Butyl vinyl ether,           3  UN2352                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
          stabilized.
         n-Butylamine.......          3  UN1125                 II  3, 8......             IB2, T7, TP1  150...........  202.......  242......         1 L         5 L  B                     40
         N-Butylaniline.....        6.1  UN2738                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     74
         tert-                      6.1  UN2747                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A             12, 13, 25
          Butylcyclohexylchl
          oroformate.
         Butylene see also          2.1  UN1012              .....  2.1.......                  19, T50  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
          Petroleum gases,
          liquefied.
         1,2-Butylene oxide,          3  UN3022                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                 27, 49
          stabilized.
         Butyltoluenes......        6.1  UN2667                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Butyltrichlorosilan          8  UN1747                 II  8, 3......    A7, B2, B6, N34, T10,  None..........  206.......  243......   Forbidden        30 L  C                     40
          e.                                                                             TP2, TP7, TP13
         1,4-Butynediol.....        6.1  UN2716                III  6.1.......   A1, IB8, IP3, T1, TP33  None..........  213.......  240......      100 kg      200 kg  C             52, 53, 70
         Butyraldehyde......          3  UN1129                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Butyraldoxime......          3  UN2840                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Butyric acid.......          8  UN2820                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                     12
         Butyric anhydride..          8  UN2739                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Butyronitrile......          3  UN2411                 II  3, 6.1....       IB2, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
         Butyryl chloride...          3  UN2353                 II  3, 8......       IB2, T8, TP2, TP13  150...........  202.......  243......         1 L         5 L  C                     40
         Cacodylic acid.....        6.1  UN1572                 II  6.1.......   IB8, IP2, IP4,T3, TP33  153...........  212.......  242......       25 kg      100 kg  E                     52
    G    Cadmium compounds..        6.1  UN2570                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A
                              .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A

[[Page 165]]

 
                              .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A
         Caesium hydroxide..          8  UN2682                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                29, 52.
         Caesium hydroxide            8  UN2681                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                 29, 52
          solution.
                                                               III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                 29, 52
         Calcium............        4.3  UN1401                 II  4.3.......       IB7, IP2, T3, TP33  151...........  212.......  241......       15 kg        50kg  E                     52
         Calcium arsenate...        6.1  UN1573                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Calcium arsenate           6.1  UN1574                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
          and calcium
          arsenite,
          mixtures, solid.
         Calcium bisulfite    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solution, see
          Bisulfites,
          aqueous solutions,
          n.o.s..
         Calcium carbide....        4.3  UN1402                  I  4.3.......   A1, A8, B55, B59, IB4,  None..........  211.......  242......   Forbidden       15 kg  B                     52
                                                                                IP1, N34, T9, TP7, TP33
         ...................  .........  ..................     II  4.3.......   A1, A8, B55, B59, IB7,  151...........  212.......  241......       15 kg       50 kg  B                     52
                                                                                     IP2, N34, T3, TP33
         Calcium chlorate...        5.1  UN1452                 II  5.1.......  A9, IB8, IP2, IP4, N34,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
                                                                                               T3, TP33
         Calcium chlorate           5.1  UN2429                 II  5.1.......    A2, IB2, N41, T4, TP1  152...........  202.......  242......         1 L         5 L  B            56, 58, 133
          aqueous solution.
         ...................  .........  ..................    III  5.1.......    A2, IB2, N41, T4, TP1  152...........  203.......  241......       2.5 L        30 L  B            56, 68, 133
         Calcium chlorite...        5.1  UN1453                 II  5.1.......  A9, IB8, IP2, IP4, N34,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
                                                                                               T3, TP33
         Calcium cyanamide          4.3  UN1403                III  4.3.......   A1, A19, IB8, IP4, T1,  151...........  213.......  241......       25 kg      100 kg  A                     52
          with more than 0.1                                                                       TP33
          percent of calcium
          carbide.
         Calcium cyanide....        6.1  UN1575                  I  6.1.......  IB7, IP1, N79, N80, T6,  None..........  211.......  242......        5 kg       50 kg  A                 40, 52
                                                                                                   TP33
         Calcium dithionite         4.2  UN1923                 II  4.2.......  A19, A20, IB6, IP2, T3,  None..........  212.......  241......       15 kg       50 kg  E                     13
          or Calcium                                                                               TP33
          hydrosulfite.
         Calcium hydride....        4.3  UN1404                  I  4.3.......                 A19, N40  None..........  211.......  242......   Forbidden       15 kg  E                     52
         Calcium              .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydrosulfite, see
          Calcium dithionite.
         Calcium                    5.1  UN3485                 II  5.1, 8....   165, 166, A7, A9, IB8,  152...........  212.......  None.....        5 kg       25 kg  D             4, 48, 52,
          hypochlorite, dry,                                                    IP2, IP4, IP13, N34, W9                                                                              56, 58, 69,
          corrosive or                                                                                                                                                                       142
          Calcium
          hypochlorite
          mixtures, dry,
          corrosive with
          more than 39%
          available chlorine
          (8.8% available
          oxygen).
         Calcium                    5.1  UN1748                 II  5.1.......   165, 166, A7, A9, IB8,  152...........  212.......  None.....        5 kg       25 kg  D             4, 25, 48,
          hypochlorite, dry                                                     IP2, IP4, IP13, N34, W9                                                                              52, 56, 58,
          or Calcium                                                                                                                                                                     69, 142
          hypochlorite
          mixtures dry with
          more than 39
          percent available
          chlorine (8.8
          percent available
          oxygen).
         ...................  .........  ..................    III  5.1.......   165, 171, A7, A9, IB8,  152...........  213.......  240......       25 kg      100 kg  D             4, 25, 48,
                                                                                     IP4, IP13, N34, W9                                                                              52, 56, 58,
                                                                                                                                                                                         69, 142

[[Page 166]]

 
         Calcium                    5.1  UN3487                 II  5.1, 8....      165, IB8, IP2, IP4,  152...........  212.......  240......        5 kg       25 kg  D             4, 48, 52,
          hypochlorite,                                                                        IP13, W9                                                                              56, 58, 69,
          hydrated,                                                                                                                                                                          142
          corrosive or
          Calcium
          hypochlorite,
          hydrated mixture,
          corrosive with not
          less than 5.5% but
          not more than 16%
          water.
                              .........  ..................    III  5.1, 8....        165, IB8, IP4, W9  152...........  213.......  240......       25 kg      100 kg  D             4, 48, 52,
                                                                                                                                                                                     56, 58, 69,
                                                                                                                                                                                             142
         Calcium                    5.1  UN2880                 II  5.1.......      165, IB8, IP2, IP4,  152...........  212.......  240......        5 kg       25 kg  D             4, 25, 48,
          hypochlorite,                                                                        IP13, W9                                                                              52, 56, 58,
          hydrated or                                                                                                                                                                   69, 142.
          Calcium
          hypochlorite,
          hydrated mixtures,
          with not less than
          5.5 percent but
          not more than 16
          percent water.
         Calcium                    5.1  UN3486                III  5.1, 8....  165, A1, A29, IB8, IP3,  152...........  213.......  240......        5 kg       25 kg  D              4,48, 52,
          hypochlorite                                                                    IP13, N34, W9                                                                              56, 58, 69,
          mixture, dry,                                                                                                                                                                      142
          corrosive with
          more than 10% but
          not more than 39%
          available chlorine.
         Calcium                    5.1  UN2208                III  5.1.......  165, A1, A29, IB8, IP3,  152...........  213.......  240......       25 kg      100 kg  D             4, 25, 48,
          hypochlorite                                                                    IP13, N34, W9                                                                              52, 56, 58,
          mixtures, dry,                                                                                                                                                                 69, 142
          with more than 10
          percent but not
          more than 39
          percent available
          chlorine.
         Calcium manganese          4.3  UN2844                III  4.3.......   A1, A19, IB8, IP4, T1,  151...........  213.......  241......       25 kg      100 kg  A            52, 85, 103
          silicon.                                                                                 TP33
         Calcium nitrate....        5.1  UN1454                III  5.1.......   34, IB8, IP3, T1, TP33  152...........  213.......  240......       25 kg      100 kg  A            ...........
    A    Calcium oxide......          8  UN1910                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
         Calcium perchlorate        5.1  UN1455                 II  5.1.......       IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
         Calcium                    5.1  UN1456                 II  5.1.......       IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  D            56, 58, 138
          permanganate.
         Calcium peroxide...        5.1  UN1457                 II  5.1.......       IB6, IP2, T3, TP33  152...........  212.......  242......        5 kg       25 kg  A            13, 52, 56,
                                                                                                                                                                                              75
         Calcium phosphide..        4.3  UN1360                  I  4.3, 6.1..             A8, A19, N40  None..........  211.......  242......   Forbidden       15 kg  E             40, 52, 85
         Calcium, pyrophoric        4.2  UN1855                  I  4.2.......  .......................  None..........  187.......  None.....   Forbidden   Forbidden  D            ...........
          or Calcium alloys,
          pyrophoric.
         Calcium resinate...        4.1  UN1313                III  4.1.......   A1, A19, IB6, T1, TP33  None..........  213.......  240......       25 kg      100 kg  A            ...........
         Calcium resinate,          4.1  UN1314                III  4.1.......   A1, A19, IB4, T1, TP33  None..........  213.......  240......       25 kg      100 kg  A            ...........
          fused.
         Calcium selenate,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Selenates or
          Selenites.

[[Page 167]]

 
         Calcium silicide...        4.3  UN1405                 II  4.3.......  A19, IB7, IP2, T3, TP33  151...........  212.......  241......       15 kg       50 kg  B            52, 85, 103
         ...................  .........  ..................    III  4.3.......   A1, A19, IB8, IP4, T1,  151...........  213.......  241......       25 kg      100 kg  B            52, 85, 103
                                                                                                   TP33
         Camphor oil........          3  UN1130                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Camphor, synthetic.        4.1  UN2717                III  4.1.......   A1, IB8, IP3, T1, TP33  None..........  213.......  240......       25 kg      100 kg  A            ...........
         Cannon primers, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Primers, tubular.
         Caproic acid.......          8  UN2829                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Caps, blasting, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Detonators, etc.
         Carbamate                    3  UN2758                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  B                     40
          pesticides,
          liquid, flammable,
          toxic, flash point
          less than 23
          degrees C.
         ...................  .........  ..................     II  3, 6.1....     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L        60 L  B                     40
                                                                                                   TP27
         Carbamate                  6.1  UN2992                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic.
         ...................  .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP2, TP28  153...........  203.......  241......        60 L       220 L  A                     40
         Carbamate                  6.1  UN2991                  I  6.1, 3....     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic,
          flammable, flash
          point not less
          than 23 degrees C.
         ...................  .........  ..................     II  6.1, 3....     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1, 3....   B1, IB3, T7, TP2, TP28  153...........  203.......  242......        60 L       220 L  A                     40
         Carbamate                  6.1  UN2757                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          pesticides, solid,
          toxic.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40
         Carbolic acid, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Phenol, solid or
          Phenol, molten.
         Carbolic acid        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solutions, see
          Phenol solutions.
    I    Carbon, activated..        4.2  UN1362                III  4.2.......       IB8, IP3, T1, TP33  None..........  213.......  241......      0.5 kg      0.5 kg  A                     12
    I    Carbon, animal or          4.2  UN1361                 II  4.2.......            IB6, T3, TP33  None..........  212.......  242......   Forbidden   Forbidden  A                     12
          vegetable origin.
         ...................  .........  ..................    III  4.2.......       IB8, IP3, T1, TP33  None..........  213.......  241......   Forbidden   Forbidden  A                     12
         Carbon bisulfide,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Carbon
          disulfide.
         Carbon dioxide.....        2.2  UN1013              .....  2.2.......  .......................  306...........  302, 304..  302, 314,       75 kg      150 kg  A            ...........
                                                                                                                                      315.
         Carbon dioxide,            2.2  UN2187              .....  2.2.......                 T75, TP5  306...........  304.......  314, 315.       50 kg      500 kg  D
          refrigerated
          liquid.
  A W    Carbon dioxide,              9  UN1845              .....  None......  .......................  217...........  217.......  240......      200 kg      200 kg  C                     40
          solid or Dry ice.
         Carbon disulfide...          3  UN1131                  I  3, 6.1....      B16, T14, TP2, TP7,  None..........  201.......  243......   Forbidden   Forbidden  D            40, 78, 115
                                                                                                   TP13
         Carbon monoxide,           2.3  UN1016              .....  2.3, 2.1..                        4  None..........  302.......  314, 315.   Forbidden       25 kg  D                     40
          compressed.

[[Page 168]]

 
    D    Carbon monoxide,           2.3  NA9202              .....  2.3, 2.1..              4, T75, TP5  None..........  316.......  318......   Forbidden   Forbidden  D            ...........
          refrigerated
          liquid (cryogenic
          liquid).
         Carbon tetrabromide        6.1  UN2516                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     25
         Carbon                     6.1  UN1846                 II  6.1.......        IB2, N36, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     40
          tetrachloride.
         Carbonyl chloride,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Phosgene.
         Carbonyl fluoride..        2.3  UN2417              .....  2.3, 8....                        2  None..........  302.......  None.....   Forbidden   Forbidden  D                     40
         Carbonyl sulfide...        2.3  UN2204              .....  2.3, 2.1..                   3, B14  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
         Cartridge cases,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          empty primed, see
          Cases, cartridge,
          empty, with primer.
         Cartridges,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          actuating, for
          aircraft ejector
          seat catapult,
          fire extinguisher,
          canopy removal or
          apparatus, see
          Cartridges, power
          device.
         Cartridges,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          explosive, see
          Charges,
          demolition.
         Cartridges,
          sporting, see
          Cartridges for
          weapons, inert
          projectile, or
          Cartridges, small
          arms.
         Cartridges, flash..       1.1G  UN0049                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Cartridges, flash..       1.3G  UN0050                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden       75 kg  07           ...........
         Cartridges for            1.1C  UN0326                 II  1.1C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          weapons, blank.
         Cartridges for            1.2C  UN0413                 II  1.2C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          weapons, blank.
         Cartridges for            1.4S  UN0014                 II  None......  .......................  63............  62........  None.....       25 kg      100 kg  05           ...........
          weapons, blank or
          Cartridges, small
          arms, blank.
         Cartridges for            1.3C  UN0327                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          weapons, blank or
          Cartridges, small
          arms, blank.
         Cartridges for            1.4C  UN0338                 II  1.4C......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          weapons, blank or
          Cartridges, small
          arms, blank.
         Cartridges for            1.2C  UN0328                 II  1.2C......  .......................  None..........  62........  62.......   Forbidden   Forbidden  03           ...........
          weapons, inert
          projectile.

[[Page 169]]

 
         Cartridges for            1.4S  UN0012                 II  None......  .......................  63............  62........  None.....       25 kg      100 kg  05           ...........
          weapons, inert
          projectile or
          Cartridges, small
          arms.
         Cartridges for            1.4C  UN0339                 II  1.4C......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          weapons, inert
          projectile or
          Cartridges, small
          arms.
         Cartridges for            1.3C  UN0417                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  06           ...........
          weapons, inert
          projectile or
          Cartridges, small
          arms.
         Cartridges for            1.1F  UN0005                 II  1.1F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08           ...........
          weapons, with
          bursting charge.
         Cartridges for            1.1E  UN0006                 II  1.1E......  .......................  None..........  62........  62.......   Forbidden   Forbidden  03           ...........
          weapons, with
          bursting charge.
         Cartridges for            1.2F  UN0007                 II  1.2F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08           ...........
          weapons, with
          bursting charge.
         Cartridges for            1.2E  UN0321                 II  1.2E......  .......................  None..........  62........  62.......   Forbidden   Forbidden  03           ...........
          weapons, with
          bursting charge.
         Cartridges for            1.4F  UN0348                 II  1.4F......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08           ...........
          weapons, with
          bursting charge.
         Cartridges for            1.4E  UN0412                 II  1.4E......  .......................  None..........  62........  62.......   Forbidden       75 kg  02           ...........
          weapons, with
          bursting charge.
         Cartridges, oil           1.3C  UN0277                 II  1.3C......  .......................  None..........  62........  62.......   Forbidden   Forbidden  07           ...........
          well.
         Cartridges, oil           1.4C  UN0278                 II  1.4C......  .......................  None..........  62........  62.......   Forbidden       75 kg  06           ...........
          well.
         Cartridges, power         1.3C  UN0275                 II  1.3C......  .......................  None..........  62........  62.......   Forbidden       75 kg  07           ...........
          device.
         Cartridges, power         1.4C  UN0276                 II  1.4C......                      110  None..........  62........  62.......   Forbidden       75 kg  06           ...........
          device.
         Cartridges, power         1.4S  UN0323                 II  1.4S......                 110, 347  63............  62........  62.......       25 kg       100kg  05
          device.
         Cartridges, power         1.2C  UN0381                 II  1.2C......  .......................  None..........  62........  62.......   Forbidden   Forbidden  07           ...........
          device.
         Cartridges, safety,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          blank, see
          Cartridges for
          weapons, blank (UN
          0014).
         Cartridges, safety,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Cartriges for
          weapons, inert
          projectile, or
          Cartridges, small
          arms or
          Cartridges, power
          device (UN 0323).
         Cartridges, signal.       1.3G  UN0054                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden       75 kg  07           ...........
         Cartridges, signal.       1.4G  UN0312                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Cartridges, signal.       1.4S  UN0405                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
    D    Cartridges, small        ORM-D  ..................  .....  None......  .......................  63............  None......  None.....       30 kg       30 kg  A            ...........
          arms.                                                                                                                                      gross       gross
    D    Cartridges power         ORM-D  None                .....  None......                      347  63............  None......  None.....       30 kg       30 kg  A
          device (used to                                                                                                                            gross       gross
          project fastening
          devices)..
         Cartridges,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          starter, jet
          engine, see
          Cartridges, power
          device.
         Cases, cartridge,         1.4S  UN0055                 II  1.4S......                       50  None..........  62........  None.....       25 kg      100 kg  05           ...........
          empty with primer.
         Cases, cartridges,        1.4C  UN0379                 II  1.4C......                       50  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          empty with primer.
         Cases, combustible,       1.4C  UN0446                 II  1.4C......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          empty, without
          primer.

[[Page 170]]

 
         Cases, combustible,       1.3C  UN0447                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          empty, without
          primer.
         Casinghead gasoline  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Gasoline.
  A W    Castor beans or              9  UN2969                 II  None......  IB8, IP2, IP4, T3, TP33  155...........  204.......  240......    No limit    No limit  E                 34, 40
          Castor meal or
          Castor pomace or
          Castor flake.
    G    Caustic alkali               8  UN1719                 II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  A                 29, 52
          liquids, n.o.s..
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                 29, 52
         Caustic potash, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Potassium
          hydroxide etc.
         Caustic soda,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (etc.) see Sodium
          hydroxide etc.
         Cells, containing          4.3  UN3292                 II  4.3.......  .......................  189...........  189.......  189......       25 kg    No limit  A            ...........
          sodium.                                                                                                                                    gross
         Celluloid, in              4.1  UN2000                III  4.1.......  .......................  None..........  213.......  240......       25 kg      100 kg  A            ...........
          block, rods,
          rolls, sheets,
          tubes, etc.,
          except scrap.
         Celluloid, scrap...        4.2  UN2002                III  4.2.......                 IB8, IP3  None..........  213.......  241......   Forbidden   Forbidden  D            ...........
         Cement, see          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Adhesives
          containing
          flammable liquid.
         Cerium, slabs,             4.1  UN1333                 II  4.1.......       IB8, IP2, IP4, N34  None..........  212.......  240......       15 kg       50 kg  A                 74, 91
          ingots, or rods.
         Cerium, turnings or        4.3  UN3078                 II  4.3.......   A1, IB7, IP2, T3, TP33  151...........  212.......  242......       15 kg       50 kg  E                     52
          gritty powder.
         Cesium or Caesium..        4.3  UN1407                  I  4.3.......  A7, A19, IB4, IP1, N34,  None..........  211.......  242......   Forbidden       15 kg  D                     52
                                                                                                    N40
         Cesium nitrate or          5.1  UN1451                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            ...........
          Caesium nitrate.                                                                         TP33
    D    Charcoal                   4.2  NA1361                III  4.2.......            IB8, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A                     12
          briquettes, shell,
          screenings, wood,
          etc..
         Charges, bursting,        1.1D  UN0457                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          plastics bonded.
         Charges, bursting,        1.2D  UN0458                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          plastics bonded.
         Charges, bursting,        1.4D  UN0459                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          plastics bonded.
         Charges, bursting,        1.4S  UN0460                 II  1.4S......                      347  None..........  62........  None.....       25 kg      100 kg  05
          plastics bonded.

[[Page 171]]

 
         Charges, demolition       1.1D  UN0048                 II  1.1D......  .......................  None..........  62........  62.......   Forbidden   Forbidden  03           ...........
         Charges, depth.....       1.1D  UN0056                 II  1.1D......  .......................  None..........  62........  62.......   Forbidden   Forbidden  03           ...........
         Charges, expelling,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          explosive, for
          fire
          extinguishers, see
          Cartridges, power
          device.
         Charges, explosive,       1.1D  UN0442                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          commercial without
          detonator.
         Charges, explosive,       1.2D  UN0443                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          commercial without
          detonator.
         Charges, explosive,       1.4D  UN0444                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          commercial without
          detonator.
         Charges, explosive,       1.4S  UN0445                 II  1.4S......                      347  None..........  62........  None.....       25 kg      100 kg  05
          commercial without
          detonator.
         Charges, propelling       1.1C  UN0271                 II  1.1C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Charges, propelling       1.3C  UN0272                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Charges, propelling       1.2C  UN0415                 II  1.2C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Charges, propelling       1.4C  UN0491                 II  1.4C......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Charges,                  1.3C  UN0242                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          propelling, for
          cannon.
         Charges,                  1.1C  UN0279                 II  1.1C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          propelling, for
          cannon.
         Charges,                  1.2C  UN0414                 II  1.2C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          propelling, for
          cannon.
         Charges, shaped,          1.4D  UN0237                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          flexible, linear.
         Charges, shaped,          1.1D  UN0288                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07
          flexible, linear.
         Charges, shaped,          1.1D  UN0059                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          without detonator.
         Charges, shaped,          1.2D  UN0439                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          without detonator.
         Charges, shaped,          1.4D  UN0440                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          without detonator.
         Charges, shaped,          1.4S  UN0441                 II  1.4S......                      347  None..........  62........  None.....       25 kg      100 kg  05
          without detonator.
         Charges,                  1.1D  UN0060                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          supplementary
          explosive.
    D    Chemical kit.......          8  NA1760                 II  8.........  .......................  154...........  161.......  None.....         1 L        30 L  B                     40
         Chemical kits......          9  UN3316              .....  9.........                       15  161...........  161.......  None.....       10 kg       10 kg  A            ...........
         Chloral, anhydrous,        6.1  UN2075                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  D                     40
          stabilized.
         Chlorate and borate        5.1  UN1458                 II  5.1.......  A9, IB8, IP2, IP4, N34,  152...........  212.......  240......        5 kg       25 kg  A                 56, 58
          mixtures.                                                                            T3, TP33
         ...................  .........  ..................    III  5.1.......   A9, IB8, IP3, N34, T1,  152...........  213.......  240......       25 kg      100 kg  A                 56, 58
                                                                                                   TP33
         Chlorate and               5.1  UN1459                 II  5.1.......  A9, IB8, IP2, IP4, N34,  152...........  212.......  240......        5 kg       25 kg  A                 56, 58
          magnesium chloride                                                                   T3, TP33
          mixture solid.
                                                               III  5.1.......   A9, IB8, IP3, N34, T1,  152...........  213.......  240......       25 kg      100 kg  A                 56, 58
                                                                                                   TP33
         Chlorate and               5.1  UN3407                 II  5.1.......    A9, IB2, N34, T4, TP1  152...........  202.......  242......         1 L         5 L  A            56, 58, 133
          magnesium chloride
          mixture solution.
         ...................  .........  ..................    III  5.1.......    A9, IB2, N34, T4, TP1  152...........  203.......  241......       2.5 L        30 L  A            56, 58, 133
         Chlorate of potash,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Potassium
          chlorate.
         Chlorate of soda,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Sodium
          chlorate.

[[Page 172]]

 
    G    Chlorates,                 5.1  UN3210                 II  5.1.......        351, IB2, T4, TP1  152...........  202.......  242......         1 L         5 L  B            56, 58, 133
          inorganic, aqueous
          solution, n.o.s.
                              .........  ..................    III  5.1.......        351, IB2, T4, TP1  152...........  203.......  241......       2.5 L        30 L  B            56, 58, 133
    G    Chlorates,                 5.1  UN1461                 II  5.1.......  351, A9, IB6, IP2, N34,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
          inorganic, n.o.s.                                                                    T3, TP33
         Chloric acid               5.1  UN2626                 II  5.1.......             IB2, T4, TP1  None..........  229.......  None.....   Forbidden   Forbidden  D                 56, 58
          aqueous solution,
          with not more than
          10 percent chloric
          acid.
         Chloride of          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          phosphorus, see
          Phosphorus
          trichloride.
         Chloride of sulfur,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Sulfur
          chloride.
         Chlorinated lime,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Calcium
          hypochlorite
          mixtures, etc.
         Chlorine...........        2.3  UN1017              .....  2.3, 5.1,     2, B9, B14, N86, T50,  None..........  304.......  314, 315.   Forbidden   Forbidden  D            40, 51, 55,
                                                                     8.                            TP19                                                                              62, 68, 89,
                                                                                                                                                                                              90
         Chlorine azide.....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
    D    Chlorine dioxide,          5.1  NA9191                 II  5.1, 6.1..  .......................  None..........  229.......  None.....   Forbidden   Forbidden  E            ...........
          hydrate, frozen.
         Chlorine dioxide     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (not hydrate).
         Chlorine                   2.3  UN2548              .....  2.3, 5.1,       1, B7, B9, B14, N86  None..........  304.......  314......   Forbidden   Forbidden  D             40, 89, 90
          pentafluoride.                                             8.
         Chlorine                   2.3  UN1749              .....  2.3, 5.1,       2, B7, B9, B14, N86  None..........  304.......  314......   Forbidden   Forbidden  D             40, 89, 90
          trifluoride.                                               8.
         Chlorite solution..          8  UN1908                 II  8.........     A3, A6, A7, B2, IB2,  154...........  202.......  242......         1 L        30 L  B            26, 44, 89,
                                                                                     N34, T7, TP2, TP24                                                                                 100, 141
         ...................  .........  ..................    III  8.........     A3, A6, A7, B2, IB3,  154...........  203.......  241......         5 L        60 L  B            26, 44, 89,
                                                                                     N34, T4, TP2, TP24                                                                                 100, 141
    G    Chlorites,                 5.1  UN1462                 II  5.1.......  352, A7, IB6, IP2, N34,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
          inorganic, n.o.s.                                                                    T3, TP33
         1-Chloro-1,1-              2.1  UN2517              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  B                     40
          difluoroethane or
          Refrigerant gas R
          142b.
         3-Chloro-4-                6.1  UN2236                 II  6.1.......                      IB2  153...........  202.......  243......         5 L        60 L  B                     40
          methylphenyl
          isocyanate, liquid.

[[Page 173]]

 
         3-Chloro-4-                6.1  UN3428                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B                     40
          methylphenyl
          isocyanate, solid.
         1-Chloro-1,2,2,2-          2.2  UN1021              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          tetrafluoroethaneo
          r Refrigerant gas
          R 124.
         4-Chloro-o-                6.1  UN1579                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          toluidine
          hydrochloride,
          solid.
         4-Chloro-o-                6.1  UN3410                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          toluidine
          hydrochloride,
          solution.
         1-Chloro-2,2,2-            2.2  UN1983              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          trifluoroethane or
          Refrigerant gas R
          133a.
         Chloroacetic acid,         6.1  UN3250                 II  6.1, 8....       IB1, T7, TP3, TP28  None..........  202.......  243......   Forbidden   Forbidden  C                     40
          molten.
         Chloroacetic acid,         6.1  UN1751                 II  6.1, 8....   A3, A7, IB8, IP2, IP4,  153...........  212.......  242......       15 kg       50 kg  C                     40
          solid.                                                                          N34, T3, TP33
         Chloroacetic acid,         6.1  UN1750                 II  6.1, 8....    A7, IB2, N34, T7, TP2  153...........  202.......  243......         1 L        30 L  C                     40
          solution.
         Chloroacetone,             6.1  UN1695                  I  6.1, 3, 8.    2, B9, B14, B32, N12,  None..........  227.......  244......   Forbidden   Forbidden  D            21, 40, 100
          stabilized.                                                               N32, N34, T20, TP2,
                                                                                       TP13, TP38, TP45
         Chloroacetone        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (unstabilized).
    +    Chloroacetonitrile.        6.1  UN2668                  I  6.1, 3....    2, B9, B14, B32, IB9,  None..........  227.......  244......   Forbidden   Forbidden  A             12, 40, 52
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Chloroacetophenone,        6.1  UN3416                 II  6.1.......  A3, IB2, N12, N32, N33,  None..........  202.......  243......   Forbidden        60 L  D                 12, 40
          liquid, (CN).                                                                   T7, TP2, TP13
         Chloroacetophenone,        6.1  UN1697                 II  6.1.......  A3, IB8, IP2, IP4, N12,  None..........  212.......  None.....   Forbidden      100 kg  D                 12, 40
          solid, (CN).                                                          N32, N33, N34, T3, TP2,
                                                                                             TP13, TP33
         Chloroacetyl               6.1  UN1752                  I  6.1, 8....      2, B3, B8, B9, B14,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          chloride.                                                                 B32, B77, N34, N43,
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Chloroanilines,            6.1  UN2019                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     52
          liquid.
         Chloroanilines,            6.1  UN2018                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
          solid.
         Chloroanisidines...        6.1  UN2233                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Chlorobenzene......          3  UN1134                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Chlorobenzol, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Chlorobenzene.
         Chlorobenzotrifluor          3  UN2234                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                     40
          ides.
         Chlorobenzyl               6.1  UN2235                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          chlorides, liquid.
         Chlorobenzyl               6.1  UN3427                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          chlorides, solid.
         Chlorobutanes......          3  UN1127                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Chlorocresols              6.1  UN2669                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     12
          solution.
         ...................  .........  ..................    III  6.1.......             IB3, T7, TP2  153...........  203.......  241......        60 L       220 L  A                     12
         Chlorocresols,             6.1  UN3437                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     12
          solid.
         Chlorodifluorobromo        2.2  UN1974              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          methane or
          Refrigerant gas R
          12B1.

[[Page 174]]

 
         Chlorodifluorometha        2.2  UN1973              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ne and
          chloropentafluoroe
          thane mixture or
          Refrigerant gas R
          502 with fixed
          boiling point,
          with approximately
          49 percent
          chlorodifluorometh
          ane.
         Chlorodifluorometha        2.2  UN1018              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ne or Refrigerant
          gas R 22.
    +    Chlorodinitrobenzen        6.1  UN1577                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B                     91
          es, liquid..
    +    Chlorodinitrobenzen        6.1  UN3441                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     91
          es, solid.
         2-Chloroethanal....        6.1  UN2232                  I  6.1.......    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  TP2, TP13, TP38, TP45
         Chloroform.........        6.1  UN1888                III  6.1.......        IB3, N36, T7, TP2  153...........  203.......  241......        60 L       220 L  A                     40
    G    Chloroformates,            6.1  UN2742                 II  6.1, 8, 3.          5, IB1, T7, TP2  153...........  202.......  243......         1 L        30 L  A            12, 13, 21,
          toxic, corrosive,                                                                                                                                                          25, 40, 100
          flammable, n.o.s..
    G    Chloroformates,            6.1  UN3277                 II  6.1, 8....      IB2, T8, TP2, TP13,  153...........  202.......  243......         1 L        30 L  A            12, 13, 25,
          toxic, corrosive,                                                                        TP28                                                                                       40
          n.o.s..
         Chloromethyl               6.1  UN2745                 II  6.1, 8....       IB2, T7, TP2, TP13  153...........  202.......  243......         1 L        30 L  A            12, 13, 21,
          chloroformate.                                                                                                                                                             25, 40, 100
         Chloromethyl ethyl           3  UN2354                 II  3, 6.1....       IB2, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
          ether.
         Chloronitroanilines        6.1  UN2237                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
    +    Chloronitrobenzenes        6.1  UN3409                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A
          , liquid.
    +    Chloronitrobenzenes        6.1  UN1578                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A
          , solid.
         Chloronitrotoluenes        6.1  UN2433                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                44, 89,
          , liquid.                                                                                                                                                                     100, 141
         Chloronitrotoluenes        6.1  UN3457                III  6.1.......        IB8, IP3,T1, TP33  153...........  213.......  240......       25 kg      200 kg  A            ...........
          , solid.
         Chloropentafluoroet        2.2  UN1020              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          hane or
          Refrigerant gas R
          115.
         Chlorophenolates,            8  UN2904                III  8.........                      IB3  154...........  203.......  241......         5 L        60 L  A            ...........
          liquid or
          Phenolates, liquid.
         Chlorophenolates,            8  UN2905                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
          solid or
          Phenolates, solid.
         Chlorophenols,             6.1  UN2021                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          liquid.
         Chlorophenols,             6.1  UN2020                III  6.1.......  IB8, IP3, T1, TP1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          solid.
         Chlorophenyltrichlo          8  UN1753                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
          rosilane.                                                                            TP2, TP7

[[Page 175]]

 
    +    Chloropicrin.......        6.1  UN1580                  I  6.1.......     2, B7, B9, B14, B32,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                   B46, T22, TP2, TP13,
                                                                                             TP38, TP45
         Chloropicrin and           2.3  UN1581              .....  2.3.......     2, B9, B14, N86, T50  None..........  193.......  314, 315.   Forbidden   Forbidden  D                 25, 40
          methyl bromide
          mixtures.
         Chloropicrin and           2.3  UN1582              .....  2.3.......              2, N86, T50  None..........  193.......  245......   Forbidden   Forbidden  D                 25, 40
          methyl chloride
          mixtures.
         Chloropicrin         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixture, flammable
          (pressure not
          exceeding 14.7
          psia at 115
          degrees F flash
          point below 100
          degrees F) see
          Toxic liquids,
          flammable, etc.
    G    Chloropicrin               6.1  UN1583                  I  6.1.......                        5  None..........  201.......  243......   Forbidden   Forbidden  C                     40
          mixtures, n.o.s.
                              .........  ..................     II  6.1.......                      IB2  153...........  202.......  243......   Forbidden   Forbidden  C                     40
                              .........  ..................    III  6.1.......                      IB3  153...........  203.......  241......   Forbidden   Forbidden  C                     40
    D    Chloropivaloyl             6.1  NA9263                  I  6.1, 8....    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  B                     40
          chloride.                                                               TP4, TP13, TP38, TP45
         Chloroplatinic               8  UN2507                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
          acid, solid.
         Chloroprene,                 3  UN1991                  I  3, 6.1....      B57, T14, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  D                     40
          stabilized.
         Chloroprene,         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          uninhibited.
         1-Chloropropane....          3  UN1278                 II  3.........   IB2, IP8, N34, T7, TP2  None..........  202.......  242......   Forbidden        60 L  E            ...........
         2-Chloropropane....          3  UN2356                  I  3.........      N36, T11, TP2, TP13  150...........  201.......  243......         1 L        30 L  E            ...........
         3-Chloropropanol-1.        6.1  UN2849                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         2-Chloropropene....          3  UN2456                  I  3.........        A3, N36, T11, TP2  150...........  201.......  243......         1 L        30 L  E            ...........
         2-Chloropropionic            8  UN2511                III  8.........             IB3, T4, TP2  154...........  203.......  241......         5 L        60 L  A                      8
          acid.
         2-Chloropyridine...        6.1  UN2822                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     40
         Chlorosilanes,               8  UN2986                 II  8, 3......     T14, TP2, TP7, TP13,  None..........  206.......  243......   Forbidden        30 L  C                     40
          corrosive,                                                                               TP27
          flammable, n.o.s.
         Chlorosilanes,               8  UN2987                 II  8.........       B2, T14, TP2, TP7,  None..........  206.......  242......   Forbidden        30 L  C                     40
          corrosive, n.o.s.                                                                  TP13, TP27
         Chlorosilanes,               3  UN2985                 II  3, 8......     T14, TP2, TP7, TP13,  None..........  206.......  243......         1 L         5 L  B                     40
          flammable,                                                                               TP27
          corrosive, n.o.s.
    G    Chlorosilanes,             6.1  UN3362                 II  6.1, 3, 8.     T14, TP2, TP7, TP13,  None..........  206.......  243......         1 L        30 L  C                40, 125
          toxic, corrosive,                                                                        TP27
          flammable, n.o.s.
    G    Chlorosilanes,             6.1  UN3361                 II  6.1, 8....     T14, TP2, TP7, TP13,  None..........  206.......  243......         1 L        30 L  C                     40
          toxic, corrosive,                                                                        TP27
          n.o.s.
         Chlorosilanes,             4.3  UN2988                  I  4.3, 3, 8.  A2, T14, TP2, TP7, TP13  None..........  201.......  244......   Forbidden         1 L  D            21, 28, 40,
          water-reactive,                                                                                                                                                                49, 100
          flammable,
          corrosive, n.o.s.
    +    Chlorosulfonic acid          8  UN1754                  I  8, 6.1....    2, B9, B10, B14, B32,  None..........  227.......  244......   Forbidden   Forbidden  C                     40
          (with or without                                                         T20, TP2, TP38, TP45
          sulfur trioxide).
         Chlorotoluenes.....          3  UN2238                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Chlorotoluidines,          6.1  UN3429                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          liquid.
         Chlorotoluidines,          6.1  UN2239                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          solid.
         Chlorotrifluorometh        2.2  UN2599              .....  2.2.......  .......................  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ane and
          trifluoromethane
          azeotropic mixture
          or Refrigerant gas
          R 503 with
          approximately 60
          percent
          chlorotrifluoromet
          hane.

[[Page 176]]

 
         Chlorotrifluorometh        2.2  UN1022              .....  2.2.......  .......................  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ane or Refrigerant
          gas R 13.
         Chromic acid                 8  UN1755                 II  8.........         B2, IB2, T8, TP2  154...........  202.......  242......         1 L        30 L  C            40, 44, 89,
          solution.                                                                                                                                                                     100, 141
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  C            40, 44, 89,
                                                                                                                                                                                        100, 141
         Chromic anhydride,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Chromium
          trioxide,
          anhydrous.
         Chromic fluoride,            8  UN1756                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A                     52
          solid.
         Chromic fluoride,            8  UN1757                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A            ...........
          solution.
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Chromium nitrate...        5.1  UN2720                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            ...........
                                                                                                   TP33
         Chromium                     8  UN1758                  I  8.........    A3, A6, A7, B10, N34,  None..........  201.......  243......       0.5 L       2.5 L  C            40, 66, 74,
          oxychloride.                                                                         T10, TP2                                                                                   89, 90
         Chromium trioxide,         5.1  UN1463                 II  5.1, 6.1,   IB8, IP2, IP4, T3, TP33  None..........  212.......  242......        5 kg       25 kg  A                 66, 90
          anhydrous.                                                 8.
         Chromosulfuric acid          8  UN2240                  I  8.........      A3, A6, A7, B4, B6,  None..........  201.......  243......        0.5L        2.5L  B            40, 66, 74,
                                                                                    N34, T10, TP2, TP13                                                                                   89, 90
         Chromyl chloride,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Chromium
          oxychloride.
         Cigar and cigarette  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          lighters, charged
          with fuel, see
          Lighters or
          Lighter refills
          containing
          flammable gas..
         Coal briquettes,     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hot.
         Coal gas,                  2.3  UN1023              .....  2.3, 2.1..                        3  None..........  302.......  314, 315.   Forbidden   Forbidden  D                     40
          compressed.
         Coal tar                     3  UN1136                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          distillates,
          flammable.
         ...................  .........  ..................    III  3.........   B1, IB3, T4, TP1, TP29  150...........  203.......  242......        60 L       220 L  A            ...........
         Coal tar dye,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          corrosive, liquid,
          n.o.s, see Dyes,
          liquid or solid,
          n.o.s. or Dye
          intermediates,
          liquid or solid,
          corrosive, n.o.s..

[[Page 177]]

 
         Coating solution             3  UN1139                  I  3.........      T11, TP1, TP8, TP27  150...........  201.......  243......         1 L        30 L  E            ...........
          (includes surface
          treatments or
          coatings used for
          industrial or
          other purposes
          such as vehicle
          undercoating, drum
          or barrel lining).
         ...................  .........  ..................     II  3.........   149, IB2, T4, TP1, TP8  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cobalt                     4.1  UN2001                III  4.1.......  A19, IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A            ...........
          naphthenates,
          powder.
         Cobalt resinate,           4.1  UN1318                III  4.1.......   A1, A19, IB6, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A            ...........
          precipitated.
         Coke, hot..........  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Collodion, see       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Nitrocellulose etc.
  D G    Combustible liquid,   Comb liq  NA1993                III  None......         IB3, T1, T4, TP1  150...........  203.......  241......        60 L       220 L  A            ...........
          n.o.s..
    G    Components,               1.2B  UN0382                 II  1.2B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11
          explosive train,
          n.o.s.
    G    Components,               1.4B  UN0383                 II  1.4B......  .......................  None..........  62........  None.....   Forbidden       75 kg  06
          explosive train,
          n.o.s.
    G    Components,               1.4S  UN0384                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05
          explosive train,
          n.o.s.
    G    Components,               1.1B  UN0461                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11
          explosive train,
          n.o.s.
         Composition B, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexolite, etc.
  D G    Compounds, cleaning          8  NA1760                  I  8.........  A7, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          liquid.
         ...................  .........  ..................     II  8.........  B2, IB2, N37, T11, TP2,  154...........  202.......  242......         1 L        30 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  8.........  IB3, N37, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     40
  D G    Compounds, cleaning          3  NA1993                  I  3.........                 T11, TP1  150...........  201.......  243......         1 L        30 L  E            ...........
          liquid.
         ...................  .........  ..................     II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, B52, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                   TP29
  D G    Compounds, tree              8  NA1760                  I  8.........  A7, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          killing, liquid or
          Compounds, weed
          killing, liquid.
         ...................  .........  ..................     II  8.........  B2, IB2, N37, T11, TP2,  154...........  202.......  242......         1 L        30 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  8.........  IB3, N37, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     40
  D G    Compounds, tree              3  NA1993                  I  3.........                 T11, TP1  150...........  201.......  243......         1 L        30 L  E            ...........
          killing, liquid or
          Compounds, weed
          killing, liquid.
         ...................  .........  ..................     II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, B52, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                   TP29
  D G    Compounds, tree            6.1  NA2810                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          killing, liquid or
          Compounds, weed
          killing, liquid.
         ...................  .........  ..................     II  6.1.......      IB2, T11, TP2, TP27  153...........  202.......  243......         5 L        60 L  B                     40
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP1, TP28  153...........  203.......  241......        60 L       220 L  A                     40

[[Page 178]]

 
    G    Compressed gas,            2.1  UN1954              .....  2.1.......  .......................  306...........  302, 305..  314, 315.   Forbidden      150 kg  D                     40
          flammable, n.o.s..
    G    Compressed gas,            2.2  UN1956              .....  2.2.......  .......................  306, 307......  302, 305..  314, 315.       75 kg      150 kg  A
          n.o.s.
    G    Compressed gas,            2.2  UN3156              .....  2.2, 5.1..                      A14  306...........  302.......  314, 315.       75 kg      150 kg  D            ...........
          oxidizing, n.o.s..
  G I    Compressed gas,            2.3  UN3304              .....  2.3, 8....                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          toxic, corrosive,
          n.o.s. Inhalation
          Hazard Zone A.
  G I    Compressed gas,            2.3  UN3304              .....  2.3, 8....               2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, corrosive,
          n.o.s. Inhalation
          Hazard Zone B.
  G I    Compressed gas,            2.3  UN3304              .....  2.3, 8....                   3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, corrosive,
          n.o.s. Inhalation
          Hazard Zone C.
  G I    Compressed gas,            2.3  UN3304              .....  2.3, 8....                        4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, corrosive,
          n.o.s. Inhalation
          Hazard Zone D.
  G I    Compressed gas,            2.3  UN3305              .....  2.3, 2.1,                         1  None..........  192.......  245......   Forbidden   Forbidden  D                 17, 40
          toxic, flammable,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone A.
  G I    Compressed gas,            2.3  UN3305              .....  2.3, 2.1,                2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                 17, 40
          toxic, flammable,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone B.
  G I    Compressed gas,            2.3  UN3305              .....  2.3, 2.1,                    3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                 17, 40
          toxic, flammable,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone C.
  G I    Compressed gas,            2.3  UN3305              .....  2.3, 2.1,                         4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                 17, 40
          toxic, flammable,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone D.
    G    Compressed gas,            2.3  UN1953              .....  2.3, 2.1..                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          toxic, flammable,
          n.o.s. Inhalation
          hazard Zone A.
    G    Compressed gas,            2.3  UN1953              .....  2.3, 2.1..               2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, flammable,
          n.o.s. Inhalation
          hazard Zone B.

[[Page 179]]

 
    G    Compressed gas,            2.3  UN1953              .....  2.3, 2.1..                   3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, flammable,
          n.o.s. Inhalation
          Hazard Zone C.
    G    Compressed gas,            2.3  UN1953              .....  2.3, 2.1..                        4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, flammable,
          n.o.s. Inhalation
          Hazard Zone D.
    G    Compressed gas,            2.3  UN1955              .....  2.3.......                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          toxic, n.o.s.
          Inhalation Hazard
          Zone A.
    G    Compressed gas,            2.3  UN1955              .....  2.3.......               2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, n.o.s.
          Inhalation Hazard
          Zone B.
    G    Compressed gas,            2.3  UN1955              .....  2.3.......                   3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, n.o.s.
          Inhalation Hazard
          Zone C.
    G    Compressed gas,            2.3  UN1955              .....  2.3.......                        4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, n.o.s.
          Inhalation Hazard
          Zone D.
  G I    Compressed gas,            2.3  UN3306              .....  2.3, 5.1,                         1  None..........  192.......  244......   Forbidden   Forbidden  D             40, 89, 90
          toxic, oxdizing,                                           8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone A.
  G I    Compressed gas,            2.3  UN3306              .....  2.3, 5.1,                2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D             40, 89, 90
          toxic, oxidizing,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone B.
  G I    Compressed gas,            2.3  UN3306              .....  2.3, 5.1,                    3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D             40, 89, 90
          toxic, oxidizing,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone C.
  G I    Compressed gas,            2.3  UN3306              .....  2.3, 5.1,                         4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D             40, 89, 90
          toxic, oxidizing,                                          8.
          corrosive, n.o.s.
          Inhalation Hazard
          Zone D.
    G    Compressed gas,            2.3  UN3303              .....  2.3, 5.1..                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          toxic, oxidizing,
          n.o.s. Inhalation
          Hazard Zone A.
    G    Compressed gas,            2.3  UN3303              .....  2.3, 5.1..               2, B9, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, oxidizing,
          n.o.s. Inhalation
          Hazard Zone B.
    G    Compressed gas,            2.3  UN3303              .....  2.3, 5.1..                   3, B14  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, oxidizing,
          n.o.s. Inhalation
          Hazard Zone C.
    G    Compressed gas,            2.3  UN3303              .....  2.3, 5.1..                        4  None..........  302, 305..  314, 315.   Forbidden   Forbidden  D                     40
          toxic, oxidizing,
          n.o.s. Inhalation
          Hazard Zone D.
    D    Consumer commodity.      ORM-D  ..................  .....  None......  .......................  156, 306......  156, 306..  None.....       30 kg       30 kg  A            ...........
                                                                                                                                                     gross       gross
         Consumer commodity.          9  ID8000              .....  9.........  .......................  167...........  167.......  None.....       30 kg       30 kg  ...........
                                                                                                                                                     gross       gross
    G    Contrivances, water-      1.2L  UN0248                 II  1.2L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          activated, with                                                                                                                                                               15E, 17E
          burster, expelling
          charge or
          propelling charge.
    G    Contrivances, water-      1.3L  UN0249                 II  1.3L......  .......................  None..........  62........  None.....   Forbidden   Forbidden  08              8E, 14E,
          activated, with                                                                                                                                                               15E, 17E
          burster, expelling
          charge or
          propelling charge.
         Copper                     6.1  UN1585                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
          acetoarsenite.
         Copper acetylide...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........

[[Page 180]]

 
         Copper amine azide.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Copper arsenite....        6.1  UN1586                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Copper based                 3  UN2776                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  B                     40
          pesticides,
          liquid, flammable,
          toxic, flash point
          less than 23
          degrees C.
         ...................  .........  ..................     II  3, 6.1....     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L        60 L  B                     40
                                                                                                   TP27
         Copper based               6.1  UN3010                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic.
         ...................  .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP2, TP28  153...........  203.......  241......        60 L       220 L  A                     40
         Copper based               6.1  UN3009                  I  6.1, 3....     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic,
          flammable, flash
          point not less
          than 23 degrees C.
         ...................  .........  ..................     II  6.1, 3....     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1, 3....   B1, IB3, T7, TP2, TP28  153...........  203.......  242......        60 L       220 L  A                     40
         Copper based               6.1  UN2775                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          pesticides, solid,
          toxic.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40
         Copper chlorate....        5.1  UN2721                 II  5.1.......   A1, IB8, IP2, IP4, T3,  152...........  212.......  242......        5 kg       25 kg  A                 56, 58
                                                                                                   TP33
         Copper chloride....          8  UN2802                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
         Copper cyanide.....        6.1  UN1587                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  204.......  242......       25 kg      100 kg  A                     52
         Copper selenate,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Selenates or
          Selenites.
         Copper selenite,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Selenates or
          Selenites.
         Copper tetramine     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrate.
  A W    Copra..............        4.2  UN1363                III  4.2.......            IB8, IP3, IP7  None..........  213.......  241......   Forbidden   Forbidden  A            13, 19, 48,
                                                                                                                                                                                             119
         Cord, detonating,         1.1D  UN0065                 II  1.1D......                      102  63(a).........  62........  None.....   Forbidden   Forbidden  07           ...........
          flexible.
         Cord, detonating,         1.4D  UN0289                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          flexible.
         Cord detonating or        1.2D  UN0102                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          Fuse detonating
          metal clad.

[[Page 181]]

 
         Cord, detonating or       1.1D  UN0290                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          Fuse, detonating
          metal clad.
         Cord, detonating,         1.4D  UN0104                 II  1.4D......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          mild effect or
          Fuse, detonating,
          mild effect metal
          clad.
         Cord, igniter......       1.4G  UN0066                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Cordeau detonant     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          fuse, see Cord,
          detonating, etc;
          Cord, detonating,
          flexible.
         Cordite, see         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Powder, smokeless.
    G    Corrosive liquid,            8  UN3264                  I  8.........  A6, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          acidic, inorganic,
          n.o.s.
                                                                II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                     40
                                                               III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     40
    G    Corrosive liquid,            8  UN3265                  I  8.........  A6, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          acidic, organic,
          n.o.s..
         ...................  .........  ..................     II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                     40
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     40
    G    Corrosive liquid,            8  UN3266                  I  8.........       A6, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                 40, 52
          basic, inorganic,
          n.o.s..
         ...................  .........  ..................     II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                 40, 52
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                 40, 52
    G    Corrosive liquid,            8  UN3267                  I  8.........  A6, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  B                 40, 52
          basic, organic,
          n.o.s..
         ...................  .........  ..................     II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                 40, 52
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                 40, 52
    G    Corrosive liquid,            8  UN3301                  I  8, 4.2....                  A6, B10  None..........  201.......  243......       0.5 L       2.5 L  D            ...........
          self-heating,
          n.o.s..
         ...................  .........  ..................     II  8, 4.2....                  B2, IB1  154...........  202.......  242......         1 L        30 L  D            ...........
    G    Corrosive liquids,           8  UN2920                  I  8, 3......  A6, B10, T14, TP2, TP27  None..........  201.......  243......       0.5 L       2.5 L  C                 25, 40
          flammable, n.o.s..
         ...................  .........  ..................     II  8, 3......  B2, IB2, T11, TP2, TP27  None..........  202.......  243......         1 L        30 L  C                 25, 40
    G    Corrosive liquids,           8  UN1760                  I  8.........   A6, A7, B10, T14, TP2,  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          n.o.s..                                                                                  TP27
         ...................  .........  ..................     II  8.........  B2, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                     40
         ...................  .........  ..................    III  8.........       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A                     40
    G    Corrosive liquids,           8  UN3093                  I  8, 5.1....                   A6, A7  None..........  201.......  243......   Forbidden       2.5 L  C                     89
          oxidizing, n.o.s..
         ...................  .........  ..................     II  8, 5.1....              A6, A7, IB2  None..........  202.......  243......         1 L        30 L  C                     89
    G    Corrosive liquids,           8  UN2922                  I  8, 6.1....   A6, A7, B10, T14, TP2,  None..........  201.......  243......       0.5 L       2.5 L  B                     40
          toxic, n.o.s..                                                                     TP13, TP27
                                                                II  8, 6.1....         B3, IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  B                     40
                                                               III  8, 6.1....       IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  B                     40
    G    Corrosive liquids,           8  UN3094                  I  8, 4.3....                   A6, A7  None..........  201.......  243......   Forbidden         1 L  E            ...........
          water-reactive,
          n.o.s..
         ...................  .........  ..................     II  8, 4.3....                   A6, A7  None..........  202.......  243......         1 L         5 L  E            ...........
    G    Corrosive solid,             8  UN3260                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B            ...........
          acidic, inorganic,
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B            ...........
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........

[[Page 182]]

 
    G    Corrosive solid,             8  UN3261                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B            ...........
          acidic, organic,
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B            ...........
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
    G    Corrosive solid,             8  UN3262                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B                     52
          basic, inorganic,
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B                     52
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                     52
    G    Corrosive solid,             8  UN3263                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B                     52
          basic, organic,
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B                     52
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                     52
    G    Corrosive solids,            8  UN2921                  I  8, 4.1....            IB6, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B                 12, 25
          flammable, n.o.s..
         ...................  .........  ..................     II  8, 4.1....  IB8, IP2, IP4, T3, TP33  None..........  212.......  242......       15 kg       50 kg  B                 12, 25
    G    Corrosive solids,            8  UN1759                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B            ...........
          n.o.s..
         ...................  .........  ..................     II  8.........  128, IB8, IP2, IP4, T3,  154...........  212.......  240......       15 kg       50 kg  A            ...........
                                                                                                   TP33
         ...................  .........  ..................    III  8.........  128, IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
    G    Corrosive solids,            8  UN3084                  I  8, 5.1....                 T6, TP33  None..........  211.......  242......        1 kg       25 kg  C            ...........
          oxidizing, n.o.s..
         ...................  .........  ..................     II  8, 5.1....       IB6, IP2, T3, TP33  None..........  212.......  242......       15 kg       50 kg  C            ...........
    G    Corrosive solids,            8  UN3095                  I  8, 4.2....                 T6, TP33  None..........  211.......  243......        1 kg       25 kg  C            ...........
          self-heating,
          n.o.s..
         ...................  .........  ..................     II  8, 4.2....       IB6, IP2, T3, TP33  None..........  212.......  242......       15 kg       50 kg  C            ...........
    G    Corrosive solids,            8  UN2923                  I  8, 6.1....            IB7, T6, TP33  None..........  211.......  242......        1 kg       25 kg  B                     40
          toxic, n.o.s..
         ...................  .........  ..................     II  8, 6.1....  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  B                     40
         ...................  .........  ..................    III  8, 6.1....       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  B                 40, 95
    G    Corrosive solids,            8  UN3096                  I  8, 4.3....       IB4, IP1, T6, TP33  None..........  211.......  243......        1 kg       25 kg  D            ...........
          water-reactive,
          n.o.s..
         ...................  .........  ..................     II  8, 4.3....       IB6, IP2, T3, TP33  None..........  212.......  242......       15 kg       50 kg  D            ...........
  D W    Cotton.............          9  NA1365              .....  9.........  137, IB8, IP2, IP4, W41  None..........  None......  None.....    No limit    No limit  A            ...........
  A W    Cotton waste, oily.        4.2  UN1364                III  4.2.......            IB8, IP3, IP7  None..........  213.......  None.....   Forbidden   Forbidden  A                     54
 A I W   Cotton, wet........        4.2  UN1365                III  4.2.......            IB8, IP3, IP7  None..........  204.......  241......   Forbidden   Forbidden  A            ...........
         Coumarin derivative          3  UN3024                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  B                     40
          pesticides,
          liquid, flammable,
          toxic, flash point
          less than 23
          degrees C.

[[Page 183]]

 
         ...................  .........  ..................     II  3, 6.1....     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L        60 L  B                     40
                                                                                                   TP27
         Coumarin derivative        6.1  UN3026                  I  6.1.......     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic.
         ...................  .........  ..................     II  6.1.......      IB2, T11, TP2, TP27  153...........  202.......  243......         5 L        60 L  B                     40
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP1, TP28  153...........  203.......  241......        60 L       220 L  A                     40
         Coumarin derivative        6.1  UN3025                  I  6.1, 3....     T14, TP2, TP13, TP27  None..........  201.......  243......         1 L        30 L  B                     40
          pesticides,
          liquid, toxic,
          flammable, flash
          point not less
          than 23 degrees C.
         ...................  .........  ..................     II  6.1, 3....     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  B                     40
                                                                                                   TP27
         ...................  .........  ..................    III  6.1, 3....   B1, IB3, T7, TP1, TP28  153...........  203.......  242......        60 L       220 L  A                     40
         Coumarin derivative        6.1  UN3027                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          pesticides, solid,
          toxic.
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40
         Cresols, liquid....        6.1  UN2076                 II  6.1, 8....   IB2, IP2, IP4, T7, TP2  153...........  202.......  243......         1 L        30 L  B            ...........
         Cresols, solid.....        6.1  UN3455                 II  6.1, 8....  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       15 kg       50 kg  B            ...........
         Cresylic acid......        6.1  UN2022                 II  6.1, 8....       IB2, T7, TP2, TP13  153...........  202.......  243......         1 L        30 L  B            ...........
         Crotonaldehyde or          6.1  UN1143                  I  6.1, 3....    2, 175, B9, B14, B32,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          Crotonaldehyde,                                                          B77, T20, TP2, TP13,
          stabilized.                                                                        TP38, TP45
         Crotonic acid,               8  UN3472                III  8.........                  IB8, T1  154...........  203.......  241......         5 L        60 L  A                    12.
          liquid.
         Crotonic acid,               8  UN2823                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                    12.
          solid.
         Crotonylene........          3  UN1144                  I  3.........                 T11, TP2  150...........  201.......  243......         1 L        30 L  E            ...........
         Cupriethylenediamin          8  UN1761                 II  8, 6.1....             IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  A            ...........
          e solution.
         ...................  .........  ..................    III  8, 6.1....       IB3, T7, TP1, TP28  154...........  203.......  242......         5 L        60 L  A                     95
         Cutters, cable,           1.4S  UN0070                 II  1.4S......  .......................  None..........  62........  62.......       25 kg      100 kg  05           ...........
          explosive.
         Cyanide or cyanide   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures, dry, see
          Cyanides,
          inorganic, solid,
          n.o.s..
    G    Cyanide solutions,         6.1  UN1935                  I  6.1.......     B37, T14, TP2, TP13,  None..........  201.......  243......         1 L        30 L  B                 40, 52
          n.o.s.                                                                                   TP27
                              .........  ..................     II  6.1.......     IB2, T11, TP2, TP13,  153...........  202.......  243......         5 L        60 L  A                 40, 52
                                                                                                   TP27
                              .........  ..................    III  6.1.......      IB3, T7, TP2, TP13,  153...........  203.......  241......        60 L       220 L  A                 40, 52
                                                                                                   TP28
         Cyanides,                  6.1  UN1588                  I  6.1.......  IB7, IP1, N74, N75, T6,  None..........  211.......  242......        5 kg       50 kg  A                     52
          inorganic, solid,                                                                        TP33
          n.o.s..
         ...................  .........  ..................     II  6.1.......      IB8, IP2, IP4, N74,  153...........  212.......  242......       25 kg      100 kg  A                     52
                                                                                          N75, T3, TP33
         ...................  .........  ..................    III  6.1.......  IB8, IP3, N74, N75, T1,  153...........  213.......  240......      100 kg      200 kg  A                     52
                                                                                                   TP33
         Cyanogen...........        2.3  UN1026              .....  2.3, 2.1..                        2  None..........  304.......  245......   Forbidden   Forbidden  D                     40
         Cyanogen bromide...        6.1  UN1889                  I  6.1, 8....         A6, A8, T6, TP33  None..........  211.......  242......        1 kg       15 kg  D                     40
         Cyanogen chloride,         2.3  UN1589              .....  2.3, 8....                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          stabilized.
         Cyanuric chloride..          8  UN2670                 II  8.........  IB8, IP2, IP4, T3, TP33  None..........  212.......  240......       15 kg       50 kg  A                 12, 40
         Cyanuric triazide..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........

[[Page 184]]

 
         Cyclobutane........        2.1  UN2601              .....  2.1.......  .......................  306...........  304.......  314, 315.   Forbidden      150 kg  B                     40
         Cyclobutyl                 6.1  UN2744                 II  6.1, 8, 3.       IB1, T7, TP2, TP13  153...........  202.......  243......         1 L        30 L  A            12, 13, 21,
          chloroformate.                                                                                                                                                             25, 40, 100
         1,5,9-                     6.1  UN2518                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                     40
          Cyclododecatriene.
         Cycloheptane.......          3  UN2241                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Cycloheptatriene...          3  UN2603                 II  3, 6.1....       IB2, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
         Cycloheptene.......          3  UN2242                 II  3.........         B1, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Cyclohexane........          3  UN1145                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Cyclohexanone......          3  UN1915                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cyclohexene........          3  UN2256                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Cyclohexenyltrichlo          8  UN1762                 II  8.........   A7, B2, N34, T10, TP2,  None..........  206.......  242......   Forbidden        30 L  C                     40
          rosilane.                                                                           TP7, TP13
         Cyclohexyl acetate.          3  UN2243                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cyclohexyl                 6.1  UN2488                  I  6.1, 3....    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          isocyanate.                                                             T20, TP2, TP13, TP38,
                                                                                                   TP45
         Cyclohexyl                   3  UN3054                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                 40, 95
          mercaptan.
         Cyclohexylamine....          8  UN2357                 II  8, 3......             IB2, T7, TP2  None..........  202.......  243......         1 L        30 L  A                     40
         Cyclohexyltrichloro          8  UN1763                 II  8.........   A7, B2, N34, T10, TP2,  None..........  206.......  242......   Forbidden        30 L  C                     40
          silane.                                                                             TP7, TP13
         Cyclonite and        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          cyclotetramethylen
          etetranitramine
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Cyclonite and HMX    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Cyclonite and        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          octogen mixtures,
          wetted or
          desensitized see
          RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Cyclonite, see       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Cyclotrimethylenet
          rinitramine, etc.

[[Page 185]]

 
         Cyclooctadiene       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          phosphines, see 9-
          Phosphabicyclonona
          nes.
         Cyclooctadienes....          3  UN2520                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cyclooctatetraene..          3  UN2358                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Cyclopentane.......          3  UN1146                 II  3.........             IB2, T7, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Cyclopentane,        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          methyl, see
          Methylcyclopentane.
         Cyclopentanol......          3  UN2244                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cyclopentanone.....          3  UN2245                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Cyclopentene.......          3  UN2246                 II  3.........        IB2, IP8, T7, TP2  150...........  202.......  242......         5 L        60 L  E            ...........
         Cyclopropane.......        2.1  UN1027              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
         Cyclotetramethylene  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tetranitramine
          (dry or
          unphlegmatized)
          (HMX).
         Cyclotetramethylene       1.1D  UN0484                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          tetranitramine,
          desensitized or
          Octogen,
          desensitized or
          HMX, desensitized.
         Cyclotetramethylene       1.1D  UN0226                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          tetranitramine,
          wetted or HMX,
          wetted or Octogen,
          wetted with not
          less than 15
          percent water, by
          mass.
         Cyclotrimethyleneni  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tramine and
          octogen, mixtures,
          wetted or
          desensitized see
          RDX and HMX
          mixtures, wetted
          or desensitized,
          etc.
         Cyclotrimethylenetr  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          initramine and
          cyclotetramethylen
          etetranitramine
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Cyclotrimethylenetr  .........                             ..........                           ..............  ..........  .........  ..........  ..........               ...........
          initramine and HMX
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Cyclotrimethylenetr       1.1D  UN0483                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          initramine,
          desensitized or
          Cyclonite,
          desensitized or
          Hexogen,
          desensitized or
          RDX, desensitized.

[[Page 186]]

 
         Cyclotrimethylenetr       1.1D  UN0072                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          initramine, wetted
          or Cyclonite,
          wetted or Hexogen,
          wetted or RDX,
          wetted with not
          less than 15
          percent water by
          mass.
         Cymenes............          3  UN2046                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Dangerous Goods in           9  UN3363              .....  ..........                136, A105  None..........  222.......  None.....    See A105    See A105  A.
          Machinery or
          Dangerous Goods in
          Apparatus.
         Decaborane.........        4.1  UN1868                 II  4.1, 6.1..  A19, A20, IB6, IP2, T3,  None..........  212.......  None.....   Forbidden       50 kg  A                     74
                                                                                                   TP33
         Decahydronaphthalen          3  UN1147                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          e.
         n-Decane...........          3  UN2247                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Deflagrating metal        1.3C  UN0132                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                    5E
          salts of aromatic
          nitroderivatives,
          n.o.s..
         Delay electric       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          igniter, see
          Igniters.
    D    Denatured alcohol..          3  NA1987                 II  3.........                  172, T8  150...........  202.......  242......         5 L        60 L  B            ...........
                              .........  ..................    III  3.........              172, B1, T7  150...........  203.......  242......        60 L       220 L  A            ...........
         Depth charges, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Charges, depth.
    G    Desensitized                 3  UN3379                  I  3.........                      164  None..........  201.......  None.....   Forbidden   Forbidden  D                     36
          explosive, liquid,
          n.o.s..
    G    Desensitized               4.1  UN3380                  I  4.1.......                      164  None..........  211.......  None.....   Forbidden   Forbidden  D                 28, 36
          explosive, solid,
          n.o.s..
         Detonating relays,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Detonators,
          etc.
         Detonator                 1.1B  UN0360                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
          assemblies, non-
          electric for
          blasting.
         Detonator                 1.4B  UN0361                 II  1.4B......                      103  63(f), 63(g)..  62........  None.....   Forbidden       75 kg  06           ...........
          assemblies, non-
          electric, for
          blasting.
         Detonator                 1.4S  UN0500                 II  1.4S......                      347  63(f), 63(g)..  62........  None.....       25 kg      100 kg  05
          assemblies, non-
          electric, for
          blasting.
         Detonators,               1.1B  UN0030                 II  1.1B......  .......................  63(f), 63(g)..  62........  None.....   Forbidden   Forbidden  11           ...........
          electric, for
          blasting.
         Detonators,               1.4B  UN0255                 II  1.4B......                      103  63(f), 63(g)..  62........  None.....   Forbidden       75 kg  06           ...........
          electric, for
          blasting.

[[Page 187]]

 
         Detonators,               1.4S  UN0456                 II  1.4S......                      347  63(f), 63(g)..  62........  None.....       25 kg      100 kg  05
          electric for
          blasting.
         Detonators for            1.1B  UN0073                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
          ammunition.
         Detonators for            1.2B  UN0364                 II  1.2B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
          ammunition.
         Detonators for            1.4B  UN0365                 II  1.4B......                      103  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          ammunition.
         Detonators for            1.4S  UN0366                 II  1.4S......                      347  None..........  62........  None.....       25 kg      100 kg  05
          ammunition.
         Detonators, non-          1.1B  UN0029                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
          electric, for
          blasting.
         Detonators, non-          1.4B  UN0267                 II  1.4B......                      103  63(f), 63(g)..  62........  None.....   Forbidden       75 kg  06           ...........
          electric, for
          blasting.
         Detonators, non-          1.4S  UN0455                 II  1.4S......                      347  63(f), 63(g)..  62........  None.....       25 kg      100 kg  05
          electric for
          blasting.
         Deuterium,                 2.1  UN1957              .....  2.1.......                      N89  306...........  302.......  None.....   Forbidden      150 kg  E                     40
          compressed.
         Devices, small,            2.1  UN3150              .....  2.1.......  .......................  306...........  304.......  None.....        1 kg       15 kg  B                     40
          hydrocarbon gas
          powered or
          Hydrocarbon gas
          refills for small
          devices with
          release device.
         Di-n-amylamine.....          3  UN2841                III  3, 6.1....         B1, IB3, T4, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Di-n-butyl           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxydicarbonate,
          with more than 52
          percent in
          solution.
         Di-n-butylamine....          8  UN2248                 II  8, 3......             IB2, T7, TP2  None..........  202.......  243......         1 L        30 L  A            ...........
         2,2-Di-(tert-        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          butylperoxy)
          butane, with more
          than 55 percent in
          solution.
         Di-(tert-            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          butylperoxy)
          phthalate, with
          more than 55
          percent in
          solution.
         2,2-Di-(4,4-di-tert- Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          butylperoxycyclohe
          xyl) propane, with
          more than 42
          percent with inert
          solid.
         Di-2,4-              Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dichlorobenzoyl
          peroxide, with
          more than 75
          percent with water.
         1,2-Di-                      3  UN2372                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          (dimethylamino)eth
          ane.
         Di-2-ethylhexyl      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          phosphoric acid,
          see Diisooctyl
          acid phosphate.
         Di-(1-               Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydroxytetrazole)
          (dry).
         Di-(1-naphthoyl)     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxide.
         a,a'-Di-(nitroxy)    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          methylether.
         Di-(beta-            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitroxyethyl)
          ammonium nitrate.
         Diacetone alcohol..          3  UN1148                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........

[[Page 188]]

 
         Diacetone alcohol    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxides, with
          more than 57
          percent in
          solution with more
          than 9 percent
          hydrogen peroxide,
          less than 26
          percent diacetone
          alcohol and less
          than 9 percent
          water; total
          active oxygen
          content more than
          9 percent by mass.
         Diacetyl, see        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Butanedione.
         Diacetyl peroxide,   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solid, or with
          more than 25
          percent in
          solution.
         Diallylamine.......          3  UN2359                 II  3, 6.1, 8.             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B            21, 40, 100
         Diallylether.......          3  UN2360                 II  3, 6.1....  IB2, N12, T7, TP1, TP13  150...........  202.......  243......         1 L        60 L  E                     40
         4,4'-                      6.1  UN2651                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          Diaminodiphenyl
          methane.
         p-Diazidobenzene...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         1,2-Diazidoethane..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         1,1'-                Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Diazoaminonaphthal
          ene.
         Diazoaminotetrazole  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (dry).
         Diazodinitrophenol   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (dry).
         Diazodinitrophenol,       1.1A  UN0074                 II  1.1A......                 111, 117  None..........  62........  None.....   Forbidden   Forbidden  12           ...........
          wetted with not
          less than 40
          percent water or
          mixture of alcohol
          and water, by mass.
         Diazodiphenylmethan  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          e.
         Diazonium nitrates   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (dry).
         Diazonium            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          perchlorates (dry).
         1,3-Diazopropane...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Dibenzyl             Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxydicarbonate,
          with more than 87
          percent with water.
         Dibenzyldichlorosil          8  UN2434                 II  8.........  B2, T10, TP2, TP7, TP13  154...........  206.......  242......   Forbidden        30 L  C                     40
          ane.
         Diborane...........        2.3  UN1911              .....  2.3, 2.1..                   1, N89  None..........  302.......  None.....   Forbidden   Forbidden  D                 40, 57
    D    Diborane mixtures..        2.1  NA1911              .....  2.1.......                        5  None..........  302.......  245......   Forbidden   Forbidden  D                 40, 57

[[Page 189]]

 
         Dibromoacetylene...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         1,2-Dibromobutan-3-        6.1  UN2648                 II  6.1.......                      IB2  153...........  202.......  243......         5 L        60 L  B                     40
          one.
         Dibromochloropropan        6.1  UN2872                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
          e.
         ...................  .........  ..................    III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
    A    Dibromodifluorometh          9  UN1941                III  None......                 T11, TP2  155...........  203.......  241......       100 L       220 L  A                     25
          ane, R12B2.
         1,2-Dibromoethane,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ethylene
          dibromide.
         Dibromomethane.....        6.1  UN2664                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Dibutyl ethers.....          3  UN1149                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Dibutylaminoethanol        6.1  UN2873                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         N,N'-                Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Dichlorazodicarbon
          amidine (salts of)
          (dry).
         1,1-Dichloro-1-            6.1  UN2650                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A             12, 40, 74
          nitroethane.
    D    3,5-Dichloro-2,4,6-        6.1  NA9264                  I  6.1.......    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  A                     40
          trifluoropyridine.                                                      TP4, TP13, TP38, TP45
         Dichloroacetic acid          8  UN1764                 II  8.........     A3, A6, A7, B2, IB2,  154...........  202.......  242......         1 L        30 L  A            ...........
                                                                                           N34, T8, TP2
         1,3-Dichloroacetone        6.1  UN2649                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B                 12, 40
         Dichloroacetyl               8  UN1765                 II  8.........      A3, A6, A7, B2, B6,  154...........  202.......  242......         1 L        30 L  D                     40
          chloride.                                                                   IB2, N34, T7, TP2
         Dichloroacetylene..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
    +    Dichloroanilines,          6.1  UN1590                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     40
          liquid.
         Dichloroanilines,          6.1  UN3442                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
          solid.
    +    o-Dichlorobenzene..        6.1  UN1591                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         2,2'-                      6.1  UN1916                 II  6.1, 3....   IB2, N33, N34, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
          Dichlorodiethyl
          ether.
         Dichlorodifluoromet        2.2  UN2602              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          hane and
          difluoroethane
          azeotropic mixture
          or Refrigerant gas
          R 500 with
          approximately 74
          percent
          dichlorodifluorome
          thane.
         Dichlorodifluoromet        2.2  UN1028              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          hane or
          Refrigerant gas R
          12.
         Dichlorodimethyl           6.1  UN2249                  I  6.1, 3....  .......................  None..........  201.......  243......   Forbidden   Forbidden  ...........           40
          ether, symmetrical.
         1,1-Dichloroethane.          3  UN2362                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         1,2-Dichloroethane,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ethylene
          dichloride.
         Dichloroethyl        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          sulfide.
         1,2-                         3  UN1150                 II  3.........             IB2, T7, TP2  150...........  202.......  242......         5 L        60 L  B            ...........
          Dichloroethylene.
         Dichlorofluorometha        2.2  UN1029              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          ne or Refrigerant
          gas R21.
         Dichloroisocyanuric        5.1  UN2465                 II  5.1.......   28, IB8, IP2, IP4, T3,  152...........  212.......  240......        5 kg       25 kg  A                     13
          acid, dry or                                                                             TP33
          Dichloroisocyanuri
          c acid salts.
         Dichloroisopropyl          6.1  UN2490                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B            ...........
          ether.
         Dichloromethane....        6.1  UN1593                III  6.1.......   IB3, IP8, N36, T7, TP2  153...........  203.......  241......        60 L       220 L  A            ...........
         Dichloropentanes...          3  UN1152                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Dichlorophenyl             6.1  UN2250                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B             25, 40, 48
          isocyanates.
         Dichlorophenyltrich          8  UN1766                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
          lorosilane.                                                                    TP2, TP7, TP13

[[Page 190]]

 
         1,2-Dichloropropane          3  UN1279                 II  3.........        IB2, N36, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         1,3-                       6.1  UN2750                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                 12, 40
          Dichloropropanol-2.
         Dichloropropene and  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          propylene
          dichloride
          mixture, see 1,2-
          Dichloropropane.
         Dichloropropenes...          3  UN2047                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Dichlorosilane.....        2.3  UN2189              .....  2.3, 2.1,                2, B9, B14  None..........  304.......  314, 315.   Forbidden   Forbidden  D                 17, 40
                                                                     8.
         1,2-Dichloro-              2.2  UN1958              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          1,1,2,2-
          tetrafluoroethane
          or Refrigerant gas
          R 114.
         Dichlorovinylchloro  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          arsine.
         Dicycloheptadiene,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Bicyclo
          [2,2,1] hepta-2,5-
          diene, stabilized.
         Dicyclohexylamine..          8  UN2565                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Dicyclohexylammoniu        4.1  UN2687                III  4.1.......       IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A                     48
          m nitrite.
         Dicyclopentadiene..          3  UN2048                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Didymium nitrate...        5.1  UN1465                III  5.1.......   A1, IB8, IP3, T1, TP33  152...........  213.......  240......       25 kg      100 kg  A            ...........
    D    Diesel fuel........          3  NA1993                III  None......   144, B1, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                   TP29
    I    Diesel fuel........          3  UN1202                III  3.........    144, B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Diethanol            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrosamine
          dinitrate (dry).
         Diethoxymethane....          3  UN2373                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         3,3-Diethoxypropene          3  UN2374                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Diethyl carbonate..          3  UN2366                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Diethyl cellosolve,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ethylene
          glycol diethyl
          ether.
         Diethyl ether or             3  UN1155                  I  3.........                 T11, TP2  150...........  201.......  243......         1 L        30 L  E                     40
          Ethyl ether.
         Diethyl ketone.....          3  UN1156                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Diethyl              Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxydicarbonate,
          with more than 27
          percent in
          solution.
         Diethyl sulfate....        6.1  UN1594                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  C            ...........
         Diethyl sulfide....          3  UN2375                 II  3.........       IB2, T7, TP1, TP13  None..........  202.......  243......         5 L        60 L  E            ...........

[[Page 191]]

 
         Diethylamine.......          3  UN1154                 II  3, 8......    A3, IB2, N34, T7, TP1  150...........  202.......  243......         1 L         5 L  E                     40
         2-                           8  UN2686                 II  8, 3......         B2, IB2, T7, TP2  None..........  202.......  243......         1 L        30 L  A            ...........
          Diethylaminoethano
          l.
         3-Diethyamino-               3  UN2684                III  3, 8......         B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A            ...........
          propylamine..
    +    N, N-Diethylaniline        6.1  UN2432                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Diethylbenzene.....          3  UN2049                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Diethyldichlorosila          8  UN1767                 II  8, 3......   A7, B6, N34, T10, TP2,  None..........  206.......  243......   Forbidden        30 L  C                     40
          ne.                                                                                 TP7, TP13
         Diethylene glycol    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrate.
         Diethyleneglycol          1.1D  UN0075                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  13                   21E
          dinitrate,
          desensitized with
          not less than 25
          percent non-
          volatile water-
          insoluble
          phlegmatizer, by
          mass.
         Diethylenetriamine.          8  UN2079                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                 40, 52
         N,N-                         8  UN2685                 II  8, 3......             IB2, T7, TP2  None..........  202.......  243......         1 L        30 L  A            ...........
          Diethylethylenedia
          mine.
         Diethylgold bromide  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Diethylthiophosphor          8  UN2751                 II  8.........         B2, IB2, T7, TP2  None..........  212.......  240......       15 kg       50 kg  D                 12, 40
          yl chloride.
         Difluorochloroethan  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          es, see 1-Chloro-
          1,1-
          difluoroethanes.
         1,1-Difluoroethane         2.1  UN1030              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  B                     40
          or Refrigerant gas
          R 152a.
         1,1-                       2.1  UN1959              .....  2.1.......  .......................  306...........  304.......  None.....   Forbidden      150 kg  E                     40
          Difluoroethylene
          or Refrigerant gas
          R 1132a.
         Difluoromethane or         2.1  UN3252              .....  2.1.......                      T50  306...........  302.......  314, 315.   Forbidden      150 kg  D                     40
          Refrigerant gas R
          32.
         Difluorophosphoric           8  UN1768                 II  8.........     A6, A7, B2, IB2, N5,  None..........  202.......  242......         1 L        30 L  A                     40
          acid, anhydrous.                                                                 N34, T8, TP2
         2,3-Dihydropyran...          3  UN2376                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         1,8-Dihydroxy-       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          2,4,5,7-
          tetranitroanthraqu
          inone
          (chrysamminic
          acid).
         Diiodoacetylene....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Diisobutyl ketone..          3  UN1157                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Diisobutylamine....          3  UN2361                III  3, 8......         B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A            ...........
         Diisobutylene,               3  UN2050                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          isomeric compounds.
         Diisooctyl acid              8  UN1902                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          phosphate.
         Diisopropyl ether..          3  UN1159                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E                     40
         Diisopropylamine...          3  UN1158                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B            ...........
         Diisopropylbenzene   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hydroperoxide,
          with more than 72
          percent in
          solution.
         Diketene,                  6.1  UN2521                  I  6.1, 3....    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D             26, 27, 40
          stabilized.                                                             TP2, TP13, TP38, TP45
         1,2-Dimethoxyethane          3  UN2252                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         1,1-Dimethoxyethane          3  UN2377                 II  3.........             IB2, T7, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Dimethyl carbonate.          3  UN1161                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Dimethyl             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          chlorothiophosphat
          e, see Dimethyl
          thiophosphoryl
          chloride.

[[Page 192]]

 
         2,5-Dimethyl-2,5-    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dihydroperoxy
          hexane, with more
          than 82 percent
          with water.
         Dimethyl disulfide.          3  UN2381                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Dimethyl ether.....        2.1  UN1033              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  B                     40
         Dimethyl-N-                  3  UN2266                 II  3, 8......       IB2, T7, TP2, TP13  150...........  202.......  243......         1 L         5 L  B                     40
          propylamine.
         Dimethyl sulfate...        6.1  UN1595                  I  6.1, 8....    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Dimethyl sulfide...          3  UN1164                 II  3.........        IB2, IP8, T7, TP2  150...........  202.......  242......         5 L        60 L  E                     40
         Dimethyl                   6.1  UN2267                 II  6.1, 8....             IB2, T7, TP2  153...........  202.......  243......         1 L        30 L  B                     25
          thiophosphoryl
          chloride.
         Dimethylamine,             2.1  UN1032              .....  2.1.......                 N87, T50  None..........  304.......  314, 315.   Forbidden      150 kg  D                     40
          anhydrous.
         Dimethylamine                3  UN1160                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B                    52.
          solution.
         2-                           3  UN2378                 II  3, 6.1....             IB2, T7, TP1  150...........  202.......  243......         1 L        60 L  A                 40, 52
          Dimethylaminoaceto
          nitrile.
         2-                           8  UN2051                 II  8, 3......         B2, IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  A            ...........
          Dimethylaminoethan
          ol.
         2-                         6.1  UN3302                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  D                     25
          Dimethylaminoethyl
          acrylate.
         2-                         6.1  UN2522                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B                     40
          Dimethylaminoethyl
          methacrylate.
         N,N-Dimethylaniline        6.1  UN2253                 II  6.1.......             IB1, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
         2,3-Dimethylbutane.          3  UN2457                 II  3.........             IB2, T7, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         1, 3-                        3  UN2379                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B                    52.
          Dimethylbutylamine.
         Dimethylcarbamoyl            8  UN2262                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                     40
          chloride.
         Dimethylcyclohexane          3  UN2263                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          s.
         N,N-                         8  UN2264                 II  8, 3......         B2, IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  A                     40
          Dimethylcyclohexyl
          amine.
         Dimethyldichlorosil          3  UN1162                 II  3, 8......      B77, T10, TP2, TP7,  None..........  206.......  243......   Forbidden   Forbidden  B                     40
          ane.                                                                                     TP13
         Dimethyldiethoxysil          3  UN2380                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          ane.
         Dimethyldioxanes...          3  UN2707                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         N,N-                         3  UN2265                III  3.........         B1, IB3, T2, TP2  150...........  203.......  242......        60 L       220 L  A            ...........
          Dimethylformamide.
         Dimethylhexane       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dihydroperoxide
          (dry).
         Dimethylhydrazine,         6.1  UN2382                  I  6.1, 3....    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D            40, 52, 74.
          symmetrical.                                                            T20, TP2, TP13, TP38,
                                                                                                   TP45

[[Page 193]]

 
         Dimethylhydrazine,         6.1  UN1163                  I  6.1, 3, 8.     2, B7, B9, B14, B32,  None..........  227.......  244......   Forbidden   Forbidden  D            21, 38, 40,
          unsymmetrical.                                                          T20, TP2, TP13, TP38,                                                                                 52, 100.
                                                                                                   TP45
         2,2-Dimethylpropane        2.1  UN2044              .....  2.1.......  .......................  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
         Dinitro-o-cresol...        6.1  UN1598                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         1,3-Dinitro-5,5-     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dimethyl hydantoin.
         Dinitro-7,8-         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dimethylglycoluril
          (dry).
         1,3-Dinitro-4,5-     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrosobenzene.
         1,4-Dinitro-1,1,4,4- Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          tetramethylolbutan
          etetranitrate
          (dry).
         2,4-Dinitro-1,3,5-   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trimethylbenzene.
         Dinitroanilines....        6.1  UN1596                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     91
         Dinitrobenzenes,           6.1  UN1597                 II  6.1.......         11, IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     91
          liquid.
         ...................  .........  ..................    III  6.1.......         11, IB3, T7, TP2  153...........  203.......  241......        60 L       220 L  A                     91
         Dinitrobenzenes,           6.1  UN3443                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     91
          solid.
         Dinitrochlorobenzen  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          e, see
          Chlorodinitrobenze
          ne.
         1,2-Dinitroethane..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         1,1-Dinitroethane    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (dry).
         Dinitrogen                 2.3  UN1067              .....  2.3, 5.1,     1, B7, B14, B45, B46,  None..........  336.......  314......   Forbidden   Forbidden  D             40, 89, 90
          tetroxide.                                                 8.             B61, B66, B67, B77,
                                                                                              T50, TP21
         Dinitroglycoluril         1.1D  UN0489                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          or Dingu.
         Dinitromethane.....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Dinitrophenol, dry        1.1D  UN0076                 II  1.1D, 6.1.  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                    5E
          or wetted with
          less than 15
          percent water, by
          mass.
         Dinitrophenol              6.1  UN1599                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A                     36
          solutions.
         ...................  .........  ..................    III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                     36
         Dinitrophenol,             4.1  UN1320                  I  4.1, 6.1..    23, A8, A19, A20, N41  None..........  211.......  None.....        1 kg       15 kg  E                 28, 36
          wetted with not
          less than 15
          percent water, by
          mass.
         Dinitrophenolates         1.3C  UN0077                 II  1.3C, 6.1.  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                    5E
          alkali metals, dry
          or wetted with
          less than 15
          percent water, by
          mass.
         Dinitrophenolates,         4.1  UN1321                  I  4.1, 6.1..    23, A8, A19, A20, N41  None..........  211.......  None.....        1 kg       15 kg  E                 28, 36
          wetted with not
          less than 15
          percent water, by
          mass.
         Dinitropropylene     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          glycol.
         Dinitroresorcinol,        1.1D  UN0078                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                    5E
          dry or wetted with
          less than 15
          percent water, by
          mass.
         2,4-                 Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Dinitroresorcinol
          (heavy metal salts
          of) (dry).

[[Page 194]]

 
         4,6-                 Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Dinitroresorcinol
          (heavy metal salts
          of) (dry).
         Dinitroresorcinol,         4.1  UN1322                  I  4.1.......    23, A8, A19, A20, N41  None..........  211.......  None.....        1 kg       15 kg  E                 28, 36
          wetted with not
          less than 15
          percent water, by
          mass.
         3,5-                 Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Dinitrosalicylic
          acid (lead salt)
          (dry).
         Dinitrosobenzene...       1.3C  UN0406                 II  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
         Dinitrosobenzylamid  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          ine and salts of
          (dry).
         2,2-Dinitrostilbene  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Dinitrotoluenes,           6.1  UN2038                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
          liquid.
         Dinitrotoluenes,           6.1  UN1600                 II  6.1.......                  T7, TP3  None..........  202.......  243......   Forbidden   Forbidden  C            ...........
          molten.
         Dinitrotoluenes,           6.1  UN3454                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
          solid.
         1,9-Dinitroxy        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          pentamethylene-
          2,4, 6,8-tetramine
          (dry).
         Dioxane............          3  UN1165                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Dioxolane..........          3  UN1166                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Dipentene..........          3  UN2052                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Diphenylamine              6.1  UN1698                  I  6.1.......                 T6, TP33  None..........  201.......  None.....   Forbidden   Forbidden  D                     40
          chloroarsine.
         Diphenylchloroarsin        6.1  UN1699                  I  6.1.......  A8, B14, B32, N33, N34,  None..........  201.......  243......   Forbidden        30 L  D                     40
          e, liquid.                                                               T14, TP2, TP13, TP27
         Diphenylchloroarsin        6.1  UN3450                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  D                     40
          e, solid.
         Diphenyldichlorosil          8  UN1769                 II  8.........   A7, B2, N34, T10, TP2,  None..........  206.......  242......   Forbidden        30 L  C                     40
          ane.                                                                                TP7, TP13
         Diphenylmethyl               8  UN1770                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  D                     40
          bromide.
         Dipicryl sulfide,         1.1D  UN0401                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          dry or wetted with
          less than 10
          percent water, by
          mass.
         Dipicryl sulfide,          4.1  UN2852                  I  4.1.......        162, A2, N41, N84  None..........  211.......  None.....   Forbidden      0.5 kg  D                     28
          wetted with not
          less than 10
          percent water, by
          mass.
         Dipicrylamine, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexanitrodiphenyla
          mine.
         Dipropionyl          Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          peroxide, with
          more than 28
          percent in
          solution.
         Di-n-propyl ether..          3  UN2384                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Dipropyl ketone....          3  UN2710                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........

[[Page 195]]

 
         Dipropylamine......          3  UN2383                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B            ...........
    G    Disinfectant,                8  UN1903                  I  8.........   A6, A7, B10, T14, TP2,  None..........  201.......  243......       0.5 L       2.5 L  B            ...........
          liquid, corrosive,                                                                       TP27
          n.o.s..
    G    Disinfectants,               8  UN1903                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  B            ...........
          liquid, corrosive
          n.o.s..
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
    G    Disinfectants,             6.1  UN3142                  I  6.1.......       A4, T14, TP2, TP27  None..........  201.......  243......         1 L        30 L  A                     40
          liquid, toxic,
          n.o.s..
         ...................  .........  ..................     II  6.1.......      IB2, T11, TP2, TP27  153...........  202.......  243......         5 L        60 L  A                     40
         ...................  .........  ..................    III  6.1.......       IB3, T7, TP1, TP28  153...........  203.......  241......        60 L       220 L  A                     40
    G    Disinfectants,             6.1  UN1601                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A                     40
          solid, toxic,
          n.o.s..
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A                     40
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     40
         Disodium                     8  UN3253                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                    52.
          trioxosilicate.
    G    Dispersant gases,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          n.o.s. see
          Refrigerant gases,
          n.o.s..
         Divinyl ether,               3  UN1167                  I  3.........             A7, T11, TP2  None..........  201.......  243......         1 L        30 L  E                     40
          stabilized.
         Dodecyltrichlorosil          8  UN1771                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
          ane.                                                                           TP2, TP7, TP13
         Dry ice, see Carbon  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dioxide, solid.
    G    Dyes, liquid,                8  UN2801                  I  8.........   11, A6, B10, T14, TP2,  None..........  201.......  243......       0.5 L       2.5 L  A
          corrosive, n.o.s.                                                                        TP27
          or Dye
          intermediates,
          liquid, corrosive,
          n.o.s.
                                                                II  8.........   11, B2, IB2, T11, TP2,  154...........  202.......  242......         1 L        30 L  A
                                                                                                   TP27
                                                               III  8.........   11, IB3, T7, TP1, TP28  154...........  203.......  241......         5 L        60 L  A
    G    Dyes, liquid,              6.1  UN1602                  I  6.1.......  .......................  None..........  201.......  243......         1 L        30 L  A            ...........
          toxic, n.o.s. or
          Dye intermediates,
          liquid, toxic,
          n.o.s..
         ...................  .........  ..................     II  6.1.......                      IB2  153...........  202.......  243......         5 L        60 L  A            ...........
         ...................  .........  ..................    III  6.1.......                      IB3  153...........  203.......  241......        60 L       220 L  A            ...........
    G    Dyes, solid,                 8  UN3147                  I  8.........       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       25 kg  A            ...........
          corrosive, n.o.s.
          or Dye
          intermediates,
          solid, corrosive,
          n.o.s..
         ...................  .........  ..................     II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A            ...........
         ...................  .........  ..................    III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
    G    Dyes, solid, toxic,        6.1  UN3143                  I  6.1.......   A5, IB7, IP1, T6, TP33  None..........  211.......  242......        5 kg       50 kg  A            ...........
          n.o.s. or Dye
          intermediates,
          solid, toxic,
          n.o.s..
         ...................  .........  ..................     II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         ...................  .........  ..................    III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Dynamite, see        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Explosive,
          blasting, type A.
         Electrolyte (acid    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          or alkali) for
          batteries, see
          Battery fluid,
          acid or Battery
          fluid, alkali.
    G    Elevated                     3  UN3256                III  3.........       IB1, T3, TP3, TP29  None..........  None......  247......   Forbidden   Forbidden  A
          temperature
          liquid, flammable,
          n.o.s., with flash
          point above 37.8
          C, at or above its
          flash point.

[[Page 196]]

 
    G    Elevated                     9  UN3257                III  9.........       IB1, T3, TP3, TP29  None..........  None......  247......   Forbidden   Forbidden  A                     85
          temperature
          liquid, n.o.s., at
          or above 100 C and
          below its flash
          point (including
          molten metals,
          molten salts,
          etc.).
    G    Elevated                     9  UN3258                III  9.........  .......................  247(h)(4).....  None......  247......   Forbidden   Forbidden  A                     85
          temperature solid,
          n.o.s., at or
          above 240 C, see
          Sec.
          173.247(h)(4).
         Engines, internal            9  UN3166              .....  9.........                      135  220...........  220.......  220......   Forbidden    No limit  A
          combustion, or
          Engines, fuel
          cell, flammable
          gas powered.
         Engines internal             9  UN3166              .....  9.........                      135  220...........  220.......  220......    No limit    No limit  A
          combustion, or
          Engines, fuel
          cell, flammable
          liquid powered.
    G    Environmentally              9  UN3082                III  9.........   8, 146, 173, 335, IB3,  155...........  203.......  241......    No limit    No limit  A            ...........
          hazardous                                                                       T4, TP1, TP29
          substance, liquid,
          n.o.s..
    G    Environmentally              9  UN3077                III  9.........  8, 146, 335, A112, B54,  155...........  213.......  240......    No limit    No limit  A
          hazardous                                                             IB8, IP3, N20, T1, TP33
          substance, solid,
          n.o.s.
         Epibromohydrin.....        6.1  UN2558                  I  6.1, 3....           T14, TP2, TP13  None..........  201.......  243......   Forbidden   Forbidden  D                     40
    +    Epichlorohydrin....        6.1  UN2023                 II  6.1, 3....       IB2, T7, TP2, TP13  153...........  202.......  243......         5 L        60 L  A                     40
         1,2-Epoxy-3-                 3  UN2752                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          ethoxypropane.
         Esters, n.o.s......          3  UN3272                 II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, IB3, T4, TP1, TP29  150...........  203.......  242......        60 L       220 L  A            ...........
         Etching acid,
          liquid, n.o.s.,
          see Hydrofluoric
          acid, etc.
         Ethane.............        2.1  UN1035              .....  2.1.......  .......................  306...........  304.......  302......   Forbidden      150 kg  E                     40
    D    Ethane-Propane             2.1  NA1961              .....  2.1.......                 T75, TP5  None..........  316.......  314, 315.   Forbidden   Forbidden  D                     40
          mixture,
          refrigerated
          liquid.
         Ethane,                    2.1  UN1961              .....  2.1.......                 T75, TP5  None..........  None......  315......   Forbidden   Forbidden  D                     40
          refrigerated
          liquid.
         Ethanol amine        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrate.
         Ethanol and                  3  UN3475                 II  3.........   144, 177, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
          gasoline mixture
          or Ethanol and
          motor spirit
          mixture or Ethanol
          and petrol
          mixture, with more
          than 10% ethanol.
         Ethanol or Ethyl             3  UN1170                 II  3.........         24, IB2, T4, TP1  4b, 150.......  202.......  242......         5 L        60 L  A
          alcohol or Ethanol
          solutions or Ethyl
          alcohol solutions.

[[Page 197]]

 
                              .........  ..................    III  3.........     24, B1, IB3, T2, TP1  4b, 150.......  203.......  242......        60 L       220 L  A
         Ethanolamine or              8  UN2491                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                    52.
          Ethanolamine
          solutions.
         Ether, see Diethyl   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          ether.
         Ethers, n.o.s......          3  UN3271                 II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, IB3, T4, TP1, TP29  150...........  203.......  242......        60 L       220 L  A            ...........
         Ethyl acetate......          3  UN1173                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Ethyl acrylate,              3  UN1917                 II  3.........       IB2, T4, TP1, TP13  150...........  202.......  242......         5 L        60 L  B                     40
          stabilized.
         Ethyl alcohol, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Ethanol.
         Ethyl aldehyde, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Acetaldehyde.
         Ethyl amyl ketone..          3  UN2271                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         N-                         6.1  UN3460                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
          Ethylbenzyltoluidi
          nes, solid.
         N-Ethyl-N-                 6.1  UN2274                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          benzylaniline.
         Ethyl borate.......          3  UN1176                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Ethyl bromide......        6.1  UN1891                 II  6.1.......  IB2, IP8, T7, TP2, TP13  153...........  202.......  243......         5 L        60 L  B                 40, 85
         Ethyl bromoacetate.        6.1  UN1603                 II  6.1, 3....             IB2, T7, TP2  None..........  202.......  243......   Forbidden   Forbidden  D                     40
         Ethyl butyl ether..          3  UN1179                 II  3.........         B1, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Ethyl butyrate.....          3  UN1180                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Ethyl chloride.....        2.1  UN1037              .....  2.1.......            B77, N86, T50  None..........  322.......  314, 315.   Forbidden      150 kg  B                     40
         Ethyl chloroacetate        6.1  UN1181                 II  6.1, 3....             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
         Ethyl chloroformate        6.1  UN1182                  I  6.1, 3, 8.    2, B9, B14, B32, N34,  None..........  227.......  244......   Forbidden   Forbidden  D            21, 40, 100
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Ethyl 2-                     3  UN2935                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          chloropropionate.
    +    Ethyl                        8  UN2826                 II  8, 6.1, 3.    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  A                     40
          chlorothioformate.                                                            TP2, TP38, TP45
         Ethyl crotonate....          3  UN1862                 II  3.........             IB2, T4, TP2  150...........  202.......  242......         5 L        60 L  B            ...........
         Ethyl ether, see     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Diethyl ether.
         Ethyl fluoride or          2.1  UN2453              .....  2.1.......  .......................  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
          Refrigerant gas
          R161.
         Ethyl formate......          3  UN1190                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Ethyl hydroperoxide  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Ethyl isobutyrate..          3  UN2385                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
    +    Ethyl isocyanate...        6.1  UN2481                  I  6.1, 3....    1, B9, B14, B30, T20,  None..........  226.......  244......   Forbidden   Forbidden  D                 40, 52
                                                                                  TP2, TP13, TP38, TP44
         Ethyl lactate......          3  UN1192                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Ethyl mercaptan....          3  UN2363                  I  3.........       A6, T11, TP2, TP13  None..........  201.......  243......   Forbidden        30 L  E                95, 102
         Ethyl methacrylate,          3  UN2277                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          stabilized.
         Ethyl methyl ether.        2.1  UN1039              .....  2.1.......  .......................  None..........  201.......  314, 315.   Forbidden      150 kg  B                     40
         Ethyl methyl ketone          3  UN1193                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          or Methyl ethyl
          ketone.
         Ethyl nitrite                3  UN1194                  I  3, 6.1....  .......................  None..........  201.......  None.....   Forbidden   Forbidden  E                40, 105
          solutions.
         Ethyl orthoformate.          3  UN2524                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Ethyl oxalate......        6.1  UN2525                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Ethyl perchlorate..  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........

[[Page 198]]

 
    D    Ethyl                      6.1  NA2927                  I  6.1, 8....    2, B9, B14, B32, B74,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          phosphonothioic                                                         T20, TP4, TP13, TP38,
          dichloride,                                                                              TP45
          anhydrous.
    D    Ethyl phosphonous          6.1  NA2845                  I  6.1, 4.2..    2, B9, B14, B32, B74,  None..........  227.......  244......   Forbidden   Forbidden  D                     18
          dichloride,                                                             T20, TP4, TP13, TP38,
          anhydrous                                                                                TP45
          pyrophoric liquid.
    D    Ethyl                      6.1  NA2927                  I  6.1, 8....    2, B9, B14, B32, B74,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          phosphorodichlorid                                                      T20, TP4, TP13, TP38,
          ate.                                                                                     TP45
         Ethyl propionate...          3  UN1195                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Ethyl propyl ether.          3  UN2615                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Ethyl silicate, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Tetraethyl
          silicate.
         Ethylacetylene,            2.1  UN2452              .....  2.1.......                      N88  None..........  304.......  314, 315.   Forbidden      150 kg  B                     40
          stabilized.
         Ethylamine.........        2.1  UN1036              .....  2.1.......            B77, N87, T50  None..........  321.......  314, 315.   Forbidden      150 kg  D                     40
         Ethylamine, aqueous          3  UN2270                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B                40, 52.
          solution with not
          less than 50
          percent but not
          more than 70
          percent ethylamine.
         N-Ethylaniline.....        6.1  UN2272                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                 52, 74
         2-Ethylaniline.....        6.1  UN2273                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                 52, 74
         Ethylbenzene.......          3  UN1175                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         N-                         6.1  UN2753                III  6.1.......             IB3, T7, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          Ethylbenzyltoluidi
          nes liquid.
         2-Ethylbutanol.....          3  UN2275                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         2-Ethylbutyl                 3  UN1177                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          acetate.
         2-                           3  UN1178                 II  3.........         B1, IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
          Ethylbutyraldehyde.
         Ethyldichloroarsine        6.1  UN1892                  I  6.1.......    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  TP2, TP13, TP38, TP45
         Ethyldichlorosilane        4.3  UN1183                  I  4.3, 8, 3.    A2, A3, A7, N34, T14,  None..........  201.......  244......   Forbidden         1 L  D            21, 28, 40,
                                                                                         TP2, TP7, TP13                                                                                  49, 100

[[Page 199]]

 
         Ethylene, acetylene        2.1  UN3138              .....  2.1.......                 T75, TP5  None..........  304.......  314, 315.   Forbidden   Forbidden  D                 40, 57
          and propylene in
          mixture,
          refrigerated
          liquid with at
          least 71.5 percent
          ethylene with not
          more than 22.5
          percent acetylene
          and not more than
          6 percent
          propylene.
         Ethylene                   6.1  UN1135                  I  6.1, 3....    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          chlorohydrin.                                                           TP2, TP13, TP38, TP45
         Ethylene...........        2.1  UN1962              .....  2.1.......  .......................  306...........  304.......  302......   Forbidden      150 kg  E                     40
         Ethylene diamine     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          diperchlorate.
         Ethylene dibromide.        6.1  UN1605                  I  6.1.......    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
                                                                                  T20, TP2, TP13, TP38,
                                                                                                   TP45
         Ethylene dibromide   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          and methyl bromide
          liquid mixtures,
          see Methyl bromide
          and ethylene
          dibromide, liquid
          mixtures.
         Ethylene dichloride          3  UN1184                 II  3, 6.1....        IB2, N36, T7, TP1  150...........  202.......  243......         1 L        60 L  B                     40
         Ethylene glycol              3  UN1153                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  A            ...........
          diethyl ether.
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Ethylene glycol      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrate.
         Ethylene glycol              3  UN1171                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          monoethyl ether.
         Ethylene glycol              3  UN1172                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          monoethyl ether
          acetate.
         Ethylene glycol              3  UN1188                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          monomethyl ether.
         Ethylene glycol              3  UN1189                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
          monomethyl ether
          acetate.
         Ethylene oxide and         2.3  UN3300              .....  2.3, 2.1..                        4  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
          carbon dioxide
          mixture with more
          than 87 percent
          ethylene oxide.
         Ethylene oxide and         2.1  UN1041              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden       25 kg  B                     40
          carbon dioxide
          mixtures with more
          than 9 percent but
          not more than 87
          percent ethylene
          oxide.
         Ethylene oxide and         2.2  UN1952              .....  2.2.......  .......................  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          carbon dioxide
          mixtures with not
          more than 9
          percent ethylene
          oxide.
         Ethylene oxide and         2.2  UN3297              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          chlorotetrafluoroe
          thane mixture with
          not more than 8.8
          percent ethylene
          oxide.
         Ethylene oxide and         2.2  UN3070              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          dichlorodifluorome
          thane mixture,
          with not more than
          12.5 percent
          ethylene oxide.

[[Page 200]]

 
         Ethylene oxide and         2.2  UN3298              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          pentafluoroethane
          mixture with not
          more than 7.9
          percent ethylene
          oxide.
         Ethylene oxide and           3  UN2983                  I  3, 6.1....    5, A11, N4, N34, T14,  None..........  201.......  243......   Forbidden        30 L  E                     40
          propylene oxide                                                                TP2, TP7, TP13
          mixtures, with not
          more than 30
          percent ethylene
          oxide.
         Ethylene oxide and         2.2  UN3299              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          tetrafluoroethane
          mixture with not
          more than 5.6
          percent ethylene
          oxide.
         Ethylene oxide or          2.3  UN1040              .....  2.3, 2.1..        4, 342, T50, TP20  None..........  323.......  323......   Forbidden   Forbidden  D                     40
          Ethylene oxide
          with nitrogen up
          to a total
          pressure of 1 MPa
          (10 bar) at 50
          degrees C.
         Ethylene,                  2.1  UN1038              .....  2.1.......                 T75, TP5  None..........  316.......  318, 319.   Forbidden   Forbidden  D                     40
          refrigerated
          liquid (cryogenic
          liquid).
         Ethylenediamine....          8  UN1604                 II  8, 3......             IB2, T7, TP2  154...........  202.......  243......         1 L        30 L  A                40, 52.
         Ethyleneimine,             6.1  UN1185                  I  6.1, 3....    1, B9, B14, B30, B77,  None..........  226.......  244......   Forbidden   Forbidden  D                     40
          stabilized.                                                               N25, N32, T22, TP2,
                                                                                       TP13, TP38, TP44
         Ethylhexaldehyde,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Octyl
          aldehydes etc.
         2-Ethylhexyl               6.1  UN2748                 II  6.1, 8....       IB2, T7, TP2, TP13  153...........  202.......  243......         1 L        30 L  A            12, 13, 21,
          chloroformate.                                                                                                                                                             25, 40, 100
         2-Ethylhexylamine..          3  UN2276                III  3, 8......         B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A                     40
         Ethylphenyldichloro          8  UN2435                 II  8.........   A7, B2, N34, T10, TP2,  None..........  206.......  242......   Forbidden        30 L  C
          silane.                                                                             TP7, TP13
         1-Ethylpiperidine..          3  UN2386                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B                    52.
         N-Ethyltoluidines..        6.1  UN2754                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
         Ethyltrichlorosilan          3  UN1196                 II  3, 8......  A7, N34, T10, TP2, TP7,  None..........  206.......  243......         1 L         5 L  B                     40
          e.                                                                                       TP13
         Etiologic agent,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Infectious
          substances, etc.
         Explosive articles,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Articles,
          explosive , n.o.s.
          etc.
         Explosive,                1.1D  UN0081                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10              19E, 21E
          blasting, type A.

[[Page 201]]

 
         Explosive,                1.1D  UN0082                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          blasting, type B.
         Explosive,                1.5D  UN0331                 II  1.5D......                  105,106  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          blasting, type B
          or Agent blasting,
          Type B.
         Explosive,                1.1D  UN0083                 II  1.1D......                      123  None..........  62........  None.....   Forbidden   Forbidden  10                   22E
          blasting, type C.
         Explosive,                1.1D  UN0084                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          blasting, type D.
         Explosive,                1.1D  UN0241                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          blasting, type E.
         Explosive,                1.5D  UN0332                 II  1.5D......                 105, 106  None..........  62........  None.....   Forbidden   Forbidden  10                   19E
          blasting, type E
          or Agent blasting,
          Type E.
         Explosive,           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          forbidden. See
          Sec.  173.54.
         Explosive            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          substances, see
          Substances,
          explosive, n.o.s.
          etc.
         Explosives, slurry,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Explosive,
          blasting, type E.
         Explosives, water    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          gels, see
          Explosive,
          blasting, type E.
         Extracts, aromatic,          3  UN1169                 II  3.........   149, IB2, T4, TP1, TP8  150...........  202.......  242......         5 L        60 L  B            ...........
          liquid.
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Extracts,                    3  UN1197                 II  3.........   149, IB2, T4, TP1, TP8  150...........  202.......  242......         5 L        60 L  B            ...........
          flavoring, liquid.
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Fabric with animal   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          or vegetable oil,
          see Fibers or
          fabrics, etc.
         Ferric arsenate....        6.1  UN1606                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Ferric arsenite....        6.1  UN1607                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
         Ferric chloride,             8  UN1773                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
          anhydrous.
         Ferric chloride,             8  UN2582                III  8.........        B15, IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
          solution.
         Ferric nitrate.....        5.1  UN1466                III  5.1.......   A1, A29, IB8, IP3, T1,  152...........  213.......  240......       25 kg      100 kg  A            ...........
                                                                                                   TP33
         Ferrocerium........        4.1  UN1323                 II  4.1.......  59, A19, IB8, IP2, IP4,  151...........  212.......  240......       15 kg       50 kg  A            ...........
                                                                                               T3, TP33
         Ferrosilicon with          4.3  UN1408                III  4.3, 6.1..   A1, A19, B6, IB8, IP4,  151...........  213.......  240......       25 kg      100 kg  A            13, 40, 52,
          30 percent or more                                                              IP7, T1, TP33                                                                              53, 85, 103
          but less than 90
          percent silicon.
         Ferrous arsenate...        6.1  UN1608                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  A            ...........
    D    Ferrous chloride,            8  NA1759                 II  8.........  IB8, IP2, IP4, T3, TP33  154...........  212.......  240......       15 kg       50 kg  A            ...........
          solid.
    D    Ferrous chloride,            8  NA1760                 II  8.........  B3, IB2, T11, TP2, TP27  154...........  202.......  242......         1 L        30 L  B                     40
          solution.
         Ferrous metal              4.2  UN2793                III  4.2.......   A1, A19, IB8, IP3, IP7  None..........  213.......  241......       25 kg      100 kg  A            ...........
          borings or Ferrous
          metal shavings or
          Ferrous metal
          turnings or
          Ferrous metal
          cuttings in a form
          liable to self-
          heating.
         Fertilizer                 2.2  UN1043              .....  2.2.......                      N87  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
          ammoniating
          solution with free
          ammonia.
A I W    Fibers, animal or          4.2  UN1372                III  4.2.......  .......................  151...........  213.......  240......   Forbidden   Forbidden  A            ...........
          Fibers, vegetable
          burnt, wet or damp.
   IW    Fibers, vegetable,         4.1  UN3360                III  4.1.......                      137  151...........  213.......  240......    No Limit    No Limit  A            ...........
          dry.
  A W    Fibers or Fabrics,         4.2  UN1373                III  4.2.......  137, IB8, IP3, T1, TP33  None..........  213.......  241......   Forbidden   Forbidden  A            ...........
          animal or
          vegetable or
          Synthetic, n.o.s.
          with animal or
          vegetable oil.

[[Page 202]]

 
         Fibers or Fabrics          4.1  UN1353                III  4.1.......             A1, IB8, IP3  None..........  213.......  240......       25 kg      100 kg  D            ...........
          impregnated with
          weakly nitrated
          nitrocellulose,
          n.o.s..
         Films,               .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrocellulose
          base, from which
          gelatine has been
          removed; film
          scrap, see
          Celluloid scrap.
         Films,                     4.1  UN1324                III  4.1.......  .......................  None..........  183.......  None.....       25 kg      100 kg  D                     28
          nitrocellulose
          base, gelatine
          coated (except
          scrap).
         Fire extinguisher            8  UN1774                 II  8.........                      N41  154...........  202.......  None.....         1 L        30 L  A            ...........
          charges, corrosive
          liquid.
         Fire extinguisher    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          charges,
          expelling,
          explosive, see
          Cartridges, power
          device.
         Fire extinguishers         2.2  UN1044              .....  2.2.......                  18, 110  309...........  309.......  None.....       75 kg      150 kg  A            ...........
          containing
          compressed or
          liquefied gas.
         Firelighters, solid        4.1  UN2623                III  4.1.......                  A1, A19  None..........  213.......  None.....       25 kg      100 kg  A                     52
          with flammable
          liquid.
         Fireworks..........       1.1G  UN0333                 II  1.1G......                      108  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Fireworks..........       1.2G  UN0334                 II  1.2G......                      108  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Fireworks..........       1.3G  UN0335                 II  1.3G......                      108  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Fireworks..........       1.4G  UN0336                 II  1.4G......                      108  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Fireworks..........       1.4S  UN0337                 II  1.4S......                      108  None..........  62........  None.....       25 kg      100 kg  05           ...........
         First aid kits.....          9  UN3316              .....  9.........                       15  161...........  161.......  None.....       10 kg       10 kg  A            ...........
    W    Fish meal,                   9  UN2216                III  None......  155, IB8, IP3, T1, TP33  155...........  218.......  218......    No limit    No limit  B               88, 122,
          stabilized or Fish                                                                                                                                                                 128
          scrap, stabilized.
         Fish meal,                 4.2  UN1374                 II  4.2.......  155, A1, A19, IB8, IP2,  None..........  212.......  241......       15 kg       50 kg  B                18, 128
          unstablized or                                                                  IP4, T3, TP33
          Fish scrap,
          unstabilized.
         Flammable            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          compressed gas,
          see Compressed or
          Liquefied gas,
          flammable, etc.
         Flammable            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          compressed gas
          (small receptacles
          not fitted with a
          dispersion device,
          not refillable),
          see Receptacles,
          etc.

[[Page 203]]

 
         Flammable gas in     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          lighters, see
          Lighters or
          lighter refills,
          cigarettes,
          containing
          flammable gas.
    G    Flammable liquid,            3  UN3286                  I  3, 6.1, 8.     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden       2.5 L  E            21, 40, 100
          toxic, corrosive,
          n.o.s..
         ...................  .........  ..................     II  3, 6.1, 8.     IB2, T11, TP2, TP13,  150...........  202.......  243......         1 L         5 L  B            21, 40, 100
                                                                                                   TP27
    G    Flammable liquids,           3  UN2924                  I  3, 8......                 T14, TP2  None..........  201.......  243......       0.5 L       2.5 L  E                     40
          corrosive, n.o.s..
         ...................  .........  ..................     II  3, 8......      IB2, T11, TP2, TP27  150...........  202.......  243......         1 L         5 L  B                     40
         ...................  .........  ..................    III  3, 8......   B1, IB3, T7, TP1, TP28  150...........  203.......  242......         5 L        60 L  A                     40
    G    Flammable liquids,           3  UN1993                  I  3.........           T11, TP1, TP27  150...........  201.......  243......         1 L        30 L  E            ...........
          n.o.s..
         ...................  .........  ..................     II  3.........  IB2, T7, TP1, TP8, TP28  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........   B1, B52, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                   TP29
    G    Flammable liquids,           3  UN1992                  I  3, 6.1....     T14, TP2, TP13, TP27  None..........  201.......  243......   Forbidden        30 L  E                     40
          toxic, n.o.s..
         ...................  .........  ..................     II  3, 6.1....       IB2, T7, TP2, TP13  150...........  202.......  243......         1 L        60 L  B                     40
         ...................  .........  ..................    III  3, 6.1....   B1, IB3, T7, TP1, TP28  150...........  203.......  242......        60 L       220 L  A            ...........
    G    Flammable solid,           4.1  UN3180                 II  4.1, 8....   A1, IB6, IP2, T3, TP33  151...........  212.......  242......       15 kg       50 kg  D                     40
          corrosive,
          inorganic, n.o.s..
         ...................  .........  ..................    III  4.1, 8....        A1, IB6, T1, TP33  151...........  213.......  242......       25 kg      100 kg  D                     40
    G    Flammable solid,           4.1  UN3178                 II  4.1.......   A1, IB8, IP2, IP4, T3,  151...........  212.......  240......       15 kg       50 kg  B            ...........
          inorganic, n.o.s..                                                                       TP33
         ...................  .........  ..................    III  4.1.......   A1, IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  B            ...........
    G    Flammable solid,           4.1  UN3176                 II  4.1.......       IB1, T3, TP3, TP26  151...........  212.......  240......   Forbidden   Forbidden  C            ...........
          organic, molten,
          n.o.s..
         ...................  .........  ..................    III  4.1.......       IB1, T1, TP3, TP26  151...........  213.......  240......   Forbidden   Forbidden  C            ...........
    G    Flammable solid,           4.1  UN3097                 II  4.1, 5.1..                      131  None..........  214.......  214......   Forbidden   Forbidden  E                     40
          oxidizing, n.o.s..
         ...................  .........  ..................    III  4.1, 5.1..            131, T1, TP33  None..........  214.......  214......   Forbidden   Forbidden  D                     40
    G    Flammable solid,           4.1  UN3179                 II  4.1, 6.1..   A1, IB6, IP2, T3, TP33  151...........  212.......  242......       15 kg       50 kg  B                     40
          toxic, inorganic,
          n.o.s..
         ...................  .........  ..................    III  4.1, 6.1..        A1, IB6, T1, TP33  151...........  213.......  242......       25 kg      100 kg  B                     40
    G    Flammable solids,          4.1  UN2925                 II  4.1, 8....   A1, IB6, IP2, T3, TP33  None..........  212.......  242......       15 kg       50 kg  D                     40
          corrosive,
          organic, n.o.s..
         ...................  .........  ..................    III  4.1, 8....        A1, IB6, T1, TP33  151...........  213.......  242......       25 kg      100 kg  D                     40
    G    Flammable solids,          4.1  UN1325                 II  4.1.......   A1, IB8, IP2, IP4, T3,  151...........  212.......  240......       15 kg       50 kg  B            ...........
          organic, n.o.s..                                                                         TP33
         ...................  .........  ..................    III  4.1.......   A1, IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  B            ...........
    G    Flammable solids,          4.1  UN2926                 II  4.1, 6.1..   A1, IB6, IP2, T3, TP33  151...........  212.......  242......       15 kg       50 kg  B                     40
          toxic, organic,
          n.o.s..
         ...................  .........  ..................    III  4.1, 6.1..        A1, IB6, T1, TP33  151...........  213.......  242......       25 kg      100 kg  B                     40
         Flares, aerial.....       1.3G  UN0093                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden       75 kg  07           ...........
         Flares, aerial.....       1.4G  UN0403                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Flares, aerial.....       1.4S  UN0404                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
         Flares, aerial.....       1.1G  UN0420                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........

[[Page 204]]

 
         Flares, aerial.....       1.2G  UN0421                 II  1.2G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Flares, airplane,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Flares, aerial.
         Flares, signal, see  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Cartridges, signal.
         Flares, surface....       1.3G  UN0092                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden       75 kg  07           ...........
         Flares, surface....       1.1G  UN0418                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Flares, surface....       1.2G  UN0419                 II  1.2G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Flares, water-       .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          activated, see
          Contrivances,
          water-activated,
          etc.
         Flash powder.......       1.1G  UN0094                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  15           ...........
         Flash powder.......       1.3G  UN0305                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  15           ...........
         Flue dusts,          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          poisonous, see
          Arsenical dust.
         Fluoric acid, see    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hydrofluoric acid,
          etc.
         Fluorine,                  2.3  UN1045              .....  2.3, 5.1,                    1, N86  None..........  302.......  None.....   Forbidden   Forbidden  D             40, 89, 90
          compressed.                                                8.
         Fluoroacetic acid..        6.1  UN2642                  I  6.1.......       IB7, IP1, T6, TP33  None..........  211.......  242......        1 kg       15 kg  E            ...........
         Fluoroanilines.....        6.1  UN2941                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Fluorobenzene......          3  UN2387                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Fluoroboric acid...          8  UN1775                 II  8.........    A6, A7, B2, B15, IB2,  154...........  202.......  242......         1 L        30 L  A            ...........
                                                                                       N3, N34, T7, TP2
         Fluorophosphoric             8  UN1776                 II  8.........     A6, A7, B2, IB2, N3,  None..........  202.......  242......         1 L        30 L  A            ...........
          acid anhydrous.                                                                  N34, T8, TP2
    G    Fluorosilicates,           6.1  UN2856                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A                     52
          n.o.s.
         Fluorosilicic acid.          8  UN1778                 II  8.........    A6, A7, B2, B15, IB2,  None..........  202.......  242......         1 L        30 L  A            ...........
                                                                                       N3, N34, T8, TP2
         Fluorosulfonic acid          8  UN1777                  I  8.........     A3, A6, A7, A10, B6,  None..........  201.......  243......       0.5 L       2.5 L  D                     40
                                                                                 B10, N3, N36, T10, TP2
         Fluorotoluenes.....          3  UN2388                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B                     40
         Forbidden            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          materials. See
          Sec.  173.21.
         Formaldehyde                 3  UN1198                III  3, 8......    176, B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A                     40
          solutions,
          flammable.

[[Page 205]]

 
         Formaldehyde         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........
          solutions (with
          not less than 10%
          and less than 25%
          formaldehyde), see
          Aviation regulated
          liquid, n.o.s. or
          Other regulated
          substances,
          liquid, n.o.s..
         Formaldehyde                 8  UN2209                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L          60
          solutions, with
          not less than 25
          percent
          formaldehyde.
         Formalin, see        .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Formaldehyde,
          solutions.
         Formic acid with             8  UN3412                 II  8.........             IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                    40.
          not less than 10%
          but not more than
          85% acid by mass.
         Formic acid with             8  UN3412                III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A                     40
          not less than 5%
          but less than 10%
          acid by mass.
         Formic acid with             8  UN1779                 II  8, 3......    B2, B28, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A                    40.
          more than 85% acid
          by mass.
         Fracturing devices,       1.1D  UN0099                 II  1.1D......  .......................  None..........  62........  62.......   Forbidden   Forbidden  07           ...........
          explosive, without
          detonators for oil
          wells.
         Fuel, aviation,              3  UN1863                  I  3.........      144, T11, TP1, TP8,  150...........  201.......  243......         1 L        30 L  E            ...........
          turbine engine.                                                                          TP28
         ...................  .........  ..................     II  3.........   144, IB2, T4, TP1, TP8  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........    144, B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Fuel cell                    8  UN3477              .....  8.........  .......................  230...........  230.......  230......        5 kg       50 kg  A
          cartridges or Fuel
          cell cartridges
          contained in
          equipment or Fuel
          cell cartridges
          packed with
          equipment,
          containing
          corrosive
          substances.
         Fuel cell                    3  UN3473              .....  3.........  .......................  230...........  230.......  230......        5 kg       50 kg  A
          cartridges or Fuel
          cell cartridges
          contained in
          equipment or Fuel
          cell cartridges
          packed with
          equipment,
          containing
          flammable liquids.
         Fuel cell                  2.1  UN3479              .....  2.1.......  .......................  230...........  230.......  230......        1 kg       15 kg  B
          cartridges or Fuel
          cell cartridges
          contained in
          equipment or Fuel
          cell cartridges
          packed with
          equipment,
          containing
          hydrogen in metal
          hydride.
         Fuel cell                  2.1  UN3478              .....  2.1.......  .......................  230...........  230.......  230......        1 kg       15 kg  B
          cartridges or Fuel
          cell cartridges
          contained in
          equipment or Fuel
          cell cartridges
          packed with
          equipment,
          containing
          liquefied
          flammable gas.

[[Page 206]]

 
         Fuel cell                  4.3  UN3476              .....  4.3.......  .......................  230...........  230.......  230......        5 kg       50 kg  A
          cartridges or Fuel
          cell cartridges
          contained in
          equipment or Fuel
          cell cartridges
          packed with
          equipment,
          containing water-
          reactive
          substances.
    D    Fuel oil (No. 1, 2,          3  NA1993                III  3.........   144, B1, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
          4, 5, or 6).                                                                             TP29
         Fuel system          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          components
          (including fuel
          control units
          (FCU),
          carburetors, fuel
          lines, fuel pumps)
          see Dangerous
          Goods in Apparatus
          or Dangerous Goods
          in Machinery.
         Fulminate of         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mercury (dry).
         Fulminate of         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mercury, wet, see
          Mercury fulminate,
          etc.
         Fulminating gold...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Fulminating mercury  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Fulminating          Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          platinum.
         Fulminating silver.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Fulminic acid......  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Fumaryl chloride...          8  UN1780                 II  8.........         B2, IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  C                  8, 40
         Fumigated lading,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Sec. Sec.
          172.302(g), 173.9
          and 176.76(h).
         Fumigated transport  .........                             ..........                           ..............  ..........  .........  ..........  ..........               ...........
          vehicle or freight
          container see Sec.
            173.9.
         Furaldehydes.......        6.1  UN1199                 II  6.1, 3....             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  A            ...........
         Furan..............          3  UN2389                  I  3.........           T12, TP2, TP13  None..........  201.......  243......         1 L        30 L  E                     40
         Furfuryl alcohol...        6.1  UN2874                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                 52, 74
         Furfurylamine......          3  UN2526                III  3, 8......         B1, IB3, T4, TP1  150...........  203.......  242......         5 L        60 L  A                     40
         Fuse, detonating,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          metal clad, see
          Cord, detonating,
          metal clad.
         Fuse, detonating,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mild effect, metal
          clad, see Cord,
          detonating, mild
          effect, metal clad.

[[Page 207]]

 
         Fuse, igniter             1.4G  UN0103                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          tubular metal clad.
         Fuse, non-                1.3G  UN0101                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          detonating
          instantaneous or
          quickmatch.
         Fuse, safety.......       1.4S  UN0105                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
    D    Fusee (railway or          4.1  NA1325                 II  4.1.......  .......................  None..........  184.......  None.....       15 kg       50 kg  B            ...........
          highway).
         Fusel oil..........          3  UN1201                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         ...................  .........  ..................    III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Fuses, tracer, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Tracers for
          ammunition.
         Fuzes, combination,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          percussion and
          time, see Fuzes,
          detonating
          (UN0257, UN0367);
          Fuzes, igniting
          (UN0317, UN0368).
         Fuzes, detonating..       1.1B  UN0106                 II  1.1B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
         Fuzes, detonating..       1.2B  UN0107                 II  1.2B......  .......................  None..........  62........  None.....   Forbidden   Forbidden  11           ...........
         Fuzes, detonating..       1.4B  UN0257                 II  1.4B......                      116  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Fuzes, detonating..       1.4S  UN0367                 II  1.4S......                      116  None..........  62........  None.....       25 kg      100 kg  05           ...........
         Fuzes, detonating,        1.1D  UN0408                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          with protective
          features.
         Fuzes, detonating,        1.2D  UN0409                 II  1.2D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
          with protective
          features.
         Fuzes, detonating,        1.4D  UN0410                 II  1.4D......                      116  None..........  62........  None.....   Forbidden       75 kg  06           ...........
          with protective
          features.
         Fuzes, igniting....       1.3G  UN0316                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Fuzes, igniting....       1.4G  UN0317                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Fuzes, igniting....       1.4S  UN0368                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
         Galactsan            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trinitrate.
         Gallium............          8  UN2803                III  8.........                 T1, TP33  None..........  162.......  240......       20 kg       20 kg  B                     48
         Gas cartridges,            2.1  UN2037              .....  2.1.......  .......................  306...........  304.......  None.....        1 kg       15 kg  B                     40
          (flammable)
          without a release
          device, non-
          refillable.
    D    Gas identification         2.3  NA9035              .....  2.3.......                        6  None..........  194.......  None.....   Forbidden   Forbidden  D            ...........
          set.
         Gas oil............          3  UN1202                III  3.........    144, B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
    G    Gas, refrigerated          2.1  UN3312              .....  2.1.......                 T75, TP5  None..........  316.......  318......   Forbidden   Forbidden  D                     40
          liquid, flammable,
          n.o.s. (cryogenic
          liquid).
    G    Gas, refrigerated          2.2  UN3158              .....  2.2.......                 T75, TP5  320...........  316.......  318......       50 kg      500 kg  D            ...........
          liquid, n.o.s.
          (cryogenic liquid).
    G    Gas, refrigerated          2.2  UN3311              .....  2.2, 5.1..           T75, TP5, TP22  320...........  316.......  318......   Forbidden   Forbidden  D            ...........
          liquid, oxidizing,
          n.o.s. (cryogenic
          liquid).
         Gas sample, non-           2.1  UN3167              .....  2.1.......  .......................  306...........  302, 304..  None.....         1 L         5 L  D            ...........
          pressurized,
          flammable, n.o.s.,
          not refrigerated
          liquid.
         Gas sample, non-           2.3  UN3168              .....  2.3, 2.1..                        6  306...........  302.......  None.....   Forbidden         1 L  D            ...........
          pressurized,
          toxic, flammable,
          n.o.s., not
          refrigerated
          liquid.

[[Page 208]]

 
         Gas sample, non-           2.3  UN3169              .....  2.3.......                        6  306...........  302, 304..  None.....   Forbidden         1 L  D                      D
          pressurized,
          toxic, n.o.s., not
          refrigerated
          liquid.
          Gasohol gasoline            3  NA1203                 II  3.........                 144, 177  150...........  202.......  242......         5 L        60 L  E            ...........
          mixed with ethyl
          alcohol, with not
          more than 10%
          alcohol.
          Gasoline includes           3  UN1203                 II  3.........  144, 177, B1, B33, IB2,  150...........  202.......  242......         5 L        60 L  E            ...........
          gasoline mixed                                                                             T8
          with ethyl
          alcohol, with not
          more than 10%
          alcohol.
         Gasoline,            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          casinghead, see
          Gasoline.
         Gelatine, blasting,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Explosive,
          blasting, type A.
         Gelatine dynamites,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Explosive,
          blasting, type A.
         Germane............        2.3  UN2192              .....  2.3, 2.1..                        2  None..........  302.......  245......   Forbidden   Forbidden  D                     40
         Glycerol-1,3-        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dinitrate.
         Glycerol gluconate   Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trinitrate.
         Glycerol lactate     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trinitrate.
         Glycerol alpha-            6.1  UN2689                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
          monochlorohydrin.
         Glyceryl             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          trinitrate, see
          Nitroglycerin, etc.
         Glycidaldehyde.....          3  UN2622                 II  3, 6.1....        IB2, IP8, T7, TP1  150...........  202.......  243......         1 L        60 L  A                     40
         Grenades, hand or         1.1D  UN0284                 II  1.1D......  .......................  ..............  62........  None.....   Forbidden   Forbidden  07           ...........
          rifle, with
          bursting charge.
         Grenades, hand or         1.2D  UN0285                 II  1.2D......  .......................  ..............  62........  None.....   Forbidden   Forbidden  07           ...........
          rifle, with
          bursting charge.
         Grenades, hand or         1.1F  UN0292                 II  1.1F......  .......................  ..............  62........  None.....   Forbidden   Forbidden  08           ...........
          rifle, with
          bursting charge.
         Grenades, hand or         1.2F  UN0293                 II  1.2F......  .......................  ..............  62........  None.....   Forbidden   Forbidden  08           ...........
          rifle, with
          bursting charge.
         Grenades,            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          illuminating, see
          Ammunition,
          illuminating, etc.
         Grenades, practice,       1.4S  UN0110                 II  1.4S......  .......................  ..............  62........  None.....       25 kg      100 kg  05           ...........
          hand or rifle.
         Grenades, practice,       1.3G  UN0318                 II  1.3G......  .......................  ..............  62........  None.....   Forbidden   Forbidden  07           ...........
          hand or rifle.
         Grenades, practice,       1.2G  UN0372                 II  1.2G......  .......................  ..............  62........  None.....   Forbidden   Forbidden  07           ...........
          hand or rifle.

[[Page 209]]

 
         Grenades practice         1.4G  UN0452                 II  1.4G......  .......................  ..............  62........  None.....   Forbidden       75 kg  06           ...........
          Hand or rifle.
         Grenades, smoke,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Ammunition,
          smoke, etc.
         Guanidine nitrate..        5.1  UN1467                III  5.1.......   A1, IB8, IP3, T1, TP33  152...........  213.......  240......       25 kg      100 kg  A                     73
         Guanyl               Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrosaminoguanyli
          dene hydrazine
          (dry).
         Guanyl                    1.1A  UN0113                 II  1.1A......                 111, 117  None..........  62........  None.....   Forbidden   Forbidden  12           ...........
          nitrosaminoguanyli
          dene hydrazine,
          wetted with not
          less than 30
          percent water, by
          mass.
         Guanyl               Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          nitrosaminoguanylt
          etrazene (dry).
         Guanyl                    1.1A  UN0114                 II  1.1A......                 111, 117  None..........  62........  None.....   Forbidden   Forbidden  12           ...........
          nitrosaminoguanylt
          etrazene, wetted
          or Tetrazene,
          wetted with not
          less than 30
          percent water or
          mixture of alcohol
          and water, by mass.
         Gunpowder,           .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          compressed or
          Gunpowder in
          pellets, see Black
          powder (UN 0028).
         Gunpowder, granular  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          or as a meal, see
          Black powder (UN
          0027).
         Hafnium powder, dry        4.2  UN2545                  I  4.2.......  .......................  None..........  211.......  242......   Forbidden   Forbidden  D            ...........
         ...................  .........  ..................     II  4.2.......      A19, A20, IB6, IP2,  None..........  212.......  241......       15 kg       50 kg  D            ...........
                                                                                          N34, T3, TP33
         ...................  .........  ..................    III  4.2.......       IB8, IP3, T1, TP33  None..........  213.......  241......       25 kg      100 kg  D            ...........
         Hafnium powder,            4.1  UN1326                 II  4.1.......  A6, A19, A20, IB6, IP2,  None..........  212.......  241......       15 kg       50 kg  E                     74
          wetted with not                                                                 N34, T3, TP33
          less than 25
          percent water (a
          visible excess of
          water must be
          present) (a)
          mechanically
          produced, particle
          size less than 53
          microns; (b)
          chemically
          produced, particle
          size less than 840
          microns.
         Hand signal device,  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Signal
          devices, hand.
         Hazardous            .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          substances, liquid
          or solid, n.o.s.,
          see
          Environmentally
          hazardous
          substances, etc.
  D G    Hazardous waste,             9  NA3082                III  9.........             IB3, T2, TP1  155...........  203.......  241......    No limit    No limit  A            ...........
          liquid, n.o.s..
  D G    Hazardous waste,             9  NA3077                III  9.........  B54, IB8, IP2, T1, TP33  155...........  213.......  240......    No limit    No limit  A            ...........
          solid, n.o.s..
         Heating oil, light.          3  UN1202                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Helium, compressed.        2.2  UN1046              .....  2.2.......  .......................  306...........  302.......  302, 314.       75 kg      150 kg  A                     85

[[Page 210]]

 
         Helium,                    2.2  UN1963              .....  2.2.......                 T75, TP5  320...........  316.......  318......       50 kg      500 kg  D
          refrigerated
          liquid (cryogenic
          liquid).
         Heptafluoropropane         2.2  UN3296              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          or Refrigerant gas
          R 227.
         n-Heptaldehyde.....          3  UN3056                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Heptanes...........          3  UN1206                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         n-Heptene..........          3  UN2278                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  B            ...........
         Hexachloroacetone..        6.1  UN2661                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  B                 12, 40
         Hexachlorobenzene..        6.1  UN2729                III  6.1.......   B3, IB8, IP3, T1, TP33  153...........  203.......  241......        60 L       220 L  A            ...........
         Hexachlorobutadiene        6.1  UN2279                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A            ...........
         Hexachlorocyclopent        6.1  UN2646                  I  6.1.......    2, B9, B14, B32, B77,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          adiene.                                                                 T20, TP2, TP13, TP38,
                                                                                                   TP45
         Hexachlorophene....        6.1  UN2875                III  6.1.......       IB8, IP3, T1, TP33  153...........  213.......  240......      100 kg      200 kg  A            ...........
         Hexadecyltrichloros          8  UN1781                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
          ilane.                                                                         TP2, TP7, TP13
         Hexadienes.........          3  UN2458                 II  3.........             IB2, T4, TP1  None..........  202.......  242......         5 L        60 L  B            ...........
         Hexaethyl                  2.3  UN1612              .....  2.3.......                        3  None..........  334.......  None.....   Forbidden   Forbidden  D                     40
          tetraphosphate and
          compressed gas
          mixtures.
         Hexaethyl                  6.1  UN1611                 II  6.1.......        IB2, N76, T7, TP2  153...........  202.......  243......         5 L        60 L  E                     40
          tetraphosphate,
          liquid.
         Hexaethyl                  6.1  UN1611                 II  6.1.......       IB8, IP2, IP4, N76  153...........  212.......  242......       25 kg      100 kg  E                     40
          tetraphosphate,
          solid.
         Hexafluoroacetone..        2.3  UN2420              .....  2.3, 8....               2, B9, B14  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
         Hexafluoroacetone          6.1  UN2552                 II  6.1.......             IB2, T7, TP2  153...........  202.......  243......         5 L        60 L  B                     40
          hydrate, liquid.
         Hexafluoroacetone          6.1  UN3436                 II  6.1.......  IB8, IP2, IP4, T3, TP33  153...........  212.......  242......       25 kg      100 kg  B                     40
          hydrate, solid.
         Hexafluoroethane,          2.2  UN2193              .....  2.2.......  .......................  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          or Refrigerant gas
          R 116.
         Hexafluorophosphori          8  UN1782                 II  8.........     A6, A7, B2, IB2, N3,  None..........  202.......  242......         1 L        30 L  A            ...........
          c acid.                                                                          N34, T8, TP2
         Hexafluoropropylene        2.2  UN1858              .....  2.2.......                      T50  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          compressed or
          Refrigerant gas R
          1216.
         Hexaldehyde........          3  UN1207                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A            ...........
         Hexamethylene              6.1  UN2281                 II  6.1.......       IB2, T7, TP2, TP13  153...........  202.......  243......         5 L        60 L  C                 13, 40
          diisocyanate.
         Hexamethylene        Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          triperoxide
          diamine (dry).

[[Page 211]]

 
         Hexamethylenediamin          8  UN2280                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A                     12
          e, solid.
         Hexamethylenediamin          8  UN1783                 II  8.........             IB2, T7, TP2  None..........  202.......  242......         1 L        30 L  A            ...........
          e solution.
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            ...........
         Hexamethyleneimine.          3  UN2493                 II  3, 8......             IB2, T7, TP1  150...........  202.......  243......         1 L         5 L  B                     40
         Hexamethylenetetram        4.1  UN1328                III  4.1.......   A1, IB8, IP3, T1, TP33  151...........  213.......  240......       25 kg      100 kg  A            ...........
          ine.
         Hexamethylol         Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          benzene
          hexanitrate.
         Hexanes............          3  UN1208                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         2,2',4,4',6,6'-      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexanitro-3,3'-
          dihydroxyazobenzen
          e (dry).
         Hexanitroazoxy       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          benzene.
         N,N'-                Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (hexanitrodiphenyl
          ) ethylene
          dinitramine (dry).
         Hexanitrodiphenyl    Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          urea.
         2,2',3',4,4',6-      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexanitrodiphenyla
          mine.
         Hexanitrodiphenylam       1.1D  UN0079                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          ine or
          Dipicrylamine or
          Hexyl.
         2,3',4,4',6,6'-      Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexanitrodiphenyle
          ther.
         Hexanitroethane....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Hexanitrooxanilide.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Hexanitrostilbene..       1.1D  UN0392                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
         Hexanoic acid, see   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Corrosive liquids,
          n.o.s..
         Hexanols...........          3  UN2282                III  3.........         B1, IB3, T2, TP1  150...........  203.......  242......        60 L       220 L  A                     74
         1-Hexene...........          3  UN2370                 II  3.........             IB2, T4, TP1  150...........  202.......  242......         5 L        60 L  E            ...........
         Hexogen and          .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          cyclotetramethylen
          etetranitramine
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Hexogen and HMX      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Hexogen and octogen  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          mixtures, wetted
          or desensitized
          see RDX and HMX
          mixtures, wetted
          or desensitized
          etc.
         Hexogen, see         .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Cyclotrimethylenet
          rinitramine, etc.
         Hexolite, or              1.1D  UN0118                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
          Hexotol dry or
          wetted with less
          than 15 percent
          water, by mass.
         Hexotonal..........       1.1D  UN0393                 II  1.1D......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10           ...........
         Hexyl, see           .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Hexanitrodiphenyla
          mine.

[[Page 212]]

 
         Hexyltrichlorosilan          8  UN1784                 II  8.........    A7, B2, B6, N34, T10,  None..........  206.......  242......   Forbidden        30 L  C                     40
          e.                                                                             TP2, TP7, TP13
         High explosives,     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see individual
          explosives'
          entries.
         HMX, see             .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Cyclotetramethylen
          ete tranitramine,
          etc.
         Hydrazine,                   8  UN2029                  I  8, 3, 6.1.     A3, A6, A7, A10, B7,  None..........  201.......  243......   Forbidden       2.5 L  D                40, 52,
          anhydrous.                                                                           B16, B53                                                                                     125.
         Hydrazine, aqueous         6.1  UN3293                III  6.1.......             IB3, T4, TP1  153...........  203.......  241......        60 L       220 L  A                    52.
          solution, with not
          more than 37
          percent hydrazine,
          by mass.
         Hydrazine aqueous            8  UN3484                  I  8, 3, 6.1.      B16, B53, T10, TP2,  None..........  201.......  243......   Forbidden       2.5 L  D            40, 52, 125
          solution,                                                                                TP13
          flammable with
          more than 37%
          hydrazine, by mass.
         Hydrazine aqueous            8  UN2030                  I  8, 6.1....      B16, B53, T10, TP2,  None..........  201.......  243......   Forbidden       2.5 L  D                 40, 52
          solution, with                                                                           TP13
          more than 37%
          hydrazine, by mass.
                                                                II  8, 6.1....  B16, B53, IB2, T7, TP2,  None..........  202.......  243......   Forbidden        30 L  D                 40, 52
                                                                                                   TP13
                                                               III  8, 6.1....   B16, B53, IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  D                 40, 52
         Hydrazine azide....  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Hydrazine chlorate.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Hydrazine            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          dicarbonic acid
          diazide.
         ...................  .........  ..................     II  8, 6.1....  B16, B53, IB2, T7, TP2,  None..........  202.......  243......   Forbidden        30 L  D                     40
                                                                                                   TP13
         ...................  .........  ..................    III  8, 6.1....   B16, B53, IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  D                     40
         Hydrazine            Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          perchlorate.
         Hydrazine selenate.  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Hydriodic acid,      .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          anhydrous, see
          Hydrogen iodide,
          anhydrous.
         Hydriodic acid.....          8  UN1787                 II  8.........    A3, A6, B2, IB2, N41,  154...........  202.......  242......         1 L        30 L  C            ...........
                                                                                                T7, TP2
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  C                      8
         Hydrobromic acid,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          anhydrous, see
          Hydrogen bromide,
          anhydrous.

[[Page 213]]

 
         Hydrobromic acid,            8  UN1788                 II  8.........   B2, B15, IB2, N41, T7,  154...........  202.......  242......   Forbidden   Forbidden  C            ...........
          with more than 49                                                                         TP2
          percent
          hydrobromic acid.
         ...................  .........  ..................    III  8.........             IB3, T4, TP1  154...........  203.......  241......   Forbidden   Forbidden  C                      8
         Hydrobromic acid,            8  UN1788                 II  8.........    A3, A6, B2, B15, IB2,  154...........  202.......  242......         1 L        30 L  C            ...........
          with not more than                                                               N41, T7, TP2
          49 percent
          hydrobromic acid.
         ...................  .........  ..................    III  8.........         A3, IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  C                      8
         Hydrocarbon gas            2.1  UN1964              .....  2.1.......  .......................  306...........  302.......  314, 315.   Forbidden      150 kg  E                     40
          mixture,
          compressed, n.o.s..
         Hydrocarbon gas            2.1  UN1965              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  E                     40
          mixture,
          liquefied, n.o.s..
         Hydrocarbons,                3  UN3295                  I  3.........      144, T11, TP1, TP8,  150...........  201.......  243......         1 L        30 L  E            ...........
          liquid, n.o.s..                                                                          TP28
         ...................  .........  ..................     II  3.........  144, IB2, T7, TP1, TP8,  150...........  202.......  242......         5 L        60 L  B            ...........
                                                                                                   TP28
         ...................  .........  ..................    III  3.........   144, B1, IB3, T4, TP1,  150...........  203.......  242......        60 L       220 L  A            ...........
                                                                                                   TP29
         Hydrochloric acid,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          anhydrous, see
          Hydrogen chloride,
          anhydrous.
         Hydrochloric acid..          8  UN1789                 II  8.........    A3, A6, B3, B15, IB2,  154...........  202.......  242......         1 L        30 L  C            ...........
                                                                                           N41, T8, TP2
         ...................  .........  ..................    III  8.........         A3, IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  C                      8
         Hydrocyanic acid,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          anhydrous, see
          Hydrogen cyanide
          etc.
         Hydrocyanic acid,          6.1  UN1613                  I  6.1.......   2, B61, B65, B77, B82,  None..........  195.......  244......   Forbidden   Forbidden  D                     40
          aqueous solutions                                                              T20, TP2, TP13
          or Hydrogen
          cyanide, aqueous
          solutions with not
          more than 20
          percent hydrogen
          cyanide.
    D    Hydrocyanic acid,          6.1  NA1613                 II  6.1.......     IB1, T14, TP2, TP13,  None..........  195.......  243......   Forbidden         5 L  D                     40
          aqueous solutions                                                                        TP27
          with less than 5
          percent hydrogen
          cyanide.
         Hydrocyanic acid,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          liquefied, see
          Hydrogen cyanide,
          etc.
         Hydrocyanic acid     Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          (prussic),
          unstabilized.
         Hydrofluoric acid            8  UN1786                  I  8, 6.1....    A6, A7, B15, B23, N5,  None..........  201.......  243......   Forbidden       2.5 L  D                     40
          and Sulfuric acid                                                         N34, T10, TP2, TP13
          mixtures.
         Hydrofluoric acid,   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          anhydrous, see
          Hydrogen fluoride,
          anhydrous.
         Hydrofluoric acid,           8  UN1790                  I  8, 6.1....    A6, A7, B4, B15, B23,  None..........  201.......  243......       0.5 L       2.5 L  D                 12, 40
          with more than 60                                                     N5, N34, T10, TP2, TP13
          percent strength.
         Hydrofluoric acid,           8  UN1790                 II  8, 6.1....    A6, A7, B15, IB2, N5,  154...........  202.......  243......         1 L        30 L  D                 12, 40
          with not more than                                                               N34, T8, TP2
          60 percent
          strength.
         Hydrofluoroboric     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          acid, see
          Fluoroboric acid.

[[Page 214]]

 
         Hydrofluorosilicic   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          acid, see
          Fluorosilicic acid.
         Hydrogen and               2.1  UN2034              .....  2.1.......                      N89  306...........  302.......  302, 314,   Forbidden      150 kg  E                 40, 57
          Methane mixtures,                                                                                                           315.
          compressed.
         Hydrogen bromide,          2.3  UN1048              .....  2.3, 8....         3, B14, N86, N89  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
          anhydrous.
         Hydrogen chloride,         2.3  UN1050              .....  2.3, 8....              3, N86, N89  None..........  304.......  None.....   Forbidden   Forbidden  D                     40
          anhydrous.
         Hydrogen chloride,         2.3  UN2186              .....  2.3, 8....                    3, B6  None..........  None......  314, 315.   Forbidden   Forbidden  B                     40
          refrigerated
          liquid.
         Hydrogen,                  2.1  UN1049              .....  2.1.......                      N89  306...........  302.......  302, 314.   Forbidden      150 kg  E                 40, 57
          compressed.
         Hydrogen cyanide,          6.1  UN3294                  I  6.1, 3....    2, B9, B14, B32, T20,  None..........  227.......  244......   Forbidden   Forbidden  D                     40
          solution in                                                             TP2, TP13, TP38, TP45
          alcohol with not
          more than 45
          percent hydrogen
          cyanide.
         Hydrogen cyanide,          6.1  UN1051                  I  6.1, 3....   1, B35, B61, B65, B77,  None..........  195.......  244......   Forbidden   Forbidden  D                     40
          stabilized with                                                                           B82
          less than 3
          percent water.
         Hydrogen cyanide,          6.1  UN1614                  I  6.1.......                        5  None..........  195.......  None.....   Forbidden   Forbidden  D                 25, 40
          stabilized, with
          less than 3
          percent water and
          absorbed in a
          porous inert
          material.
         Hydrogen fluoride,           8  UN1052                  I  8.6.1.....    3, B7, B46, B77, N86,  None..........  163.......  244......   Forbidden   Forbidden  D                     40
          anhydrous.                                                                           T10, TP2
         Hydrogen in a metal        2.1  UN3468              .....  2.1.......                      167  None..........  311.......  None.....   Forbidden      100 kg  D
          hydride storage                                                                                                                                        gross
          system or Hydrogen
          in a metal hydride
          storage system
          contained in
          equipment or
          Hydrogen in a
          metal hydride
          storage system
          packed with
          equipment.
         Hydrogen iodide,           2.3  UN2197              .....  2.3, 8....         3, B14, N86, N89  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
          anhydrous.
         Hydrogen iodide      .........                             ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          solution, see
          Hydriodic acid.
                                                               III  8.........   IB8, IP3, N3, N34, T1,  154...........  213.......  240......       25 kg      100 kg  A            25, 40, 52.
                                                                                                   TP33
         Hydrogendifluoride,          8  UN1740                 II  8.........  IB8, IP2, IP4, N3, N34,  None..........  212.......  240......       15 kg       50 kg  A             25, 40, 52
          solid, n.o.s.                                                                        T3, TP33

[[Page 215]]

 
                                                               III  8.........   IB8, IP3, N3, N34, T1,  154...........  213.......  240......       25 kg      100 kg  A             25, 40, 52
                                                                                                   TP33
         Hydrogendifluoride           8  UN3471                 II  8, 6.1....             IB2, T7, TP2  154...........  202.......  242......         1 L        30 L  A            25, 40, 52.
          solution, n.o.s.
                                                               III  8, 6.1....             IB3, T4, TP1  154...........  203.......  241......         5 L        60 L  A            25, 40, 52.
         Hydrogen peroxide          5.1  UN3149                 II  5.1, 8....    145, A2, A3, A6, B53,  None..........  202.......  243......         1 L         5 L  D            25, 66, 75.
          and peroxyacetic                                                      IB2, IP5, T7, TP2, TP6,
          acid mixtures,                                                                           TP24
          stabilized with
          acids, water, and
          not more than 5
          percent
          peroxyacetic acid.
         Hydrogen, peroxide,        5.1  UN2014                 II  5.1, 8....  12, A60, B53, B80, B81,  None..........  202.......  243......   Forbidden   Forbidden  D             25, 66, 75
          aqueous solutions                                                     B85, IB2, IP5, T7, TP2,
          with more than 40                                                             TP6, TP24, TP37
          percent but not
          more than 60
          percent hydrogen
          peroxide
          (stabilized as
          necessary).
         Hydrogen peroxide,         5.1  UN2014                 II  5.1, 8....    A2, A3, A6, B53, IB2,  None..........  202.......  243......         1 L         5 L  D            25, 66, 75.
          aqueous solutions                                                          IP5, T7, TP2, TP6,
          with not less than                                                                 TP24, TP37
          20 percent but not
          more than 40
          percent hydrogen
          peroxide
          (stabilized as
          necessary).
         Hydrogen, peroxide,        5.1  UN2984                III  5.1.......   A1, IB2, IP5, T4, TP1,  152...........  203.......  241......       2.5 L        30 L  B             25, 66, 75
          aqueous solutions                                                             TP6, TP24, TP37
          with not less than
          8 percent but less
          than 20 percent
          hydrogen peroxide
          (stabilized as
          necessary).
         Hydrogen peroxide,         5.1  UN2015                  I  5.1, 8....  12, B53, B80, B81, B85,  None..........  201.......  243......   Forbidden   Forbidden  D            25, 66, 75.
          stabilized or                                                             T9, TP2, TP6, TP24,
          Hydrogen peroxide                                                                        TP37
          aqueous solutions,
          stabilized with
          more than 60
          percent hydrogen
          peroxide.
         Hydrogen,                  2.1  UN1966              .....  2.1.......                 T75, TP5  None..........  316.......  318, 319.   Forbidden   Forbidden  D                     40
          refrigerated
          liquid (cryogenic
          liquid).
         Hydrogen selenide,         2.3  UN2202              .....  2.3, 2.1..                        1  None..........  192.......  245......   Forbidden   Forbidden  D                     40
          anhydrous.
         Hydrogen sulfate,    .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          see Sulfuric acid.
         Hydrogen sulfide...        2.3  UN1053              .....  2.3, 2.1..          2, B9, B14, N89  None..........  304.......  314, 315.   Forbidden   Forbidden  D                     40
         Hydrosilicofluoric   .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          acid, see
          Fluorosilicic acid.
         1-                        1.3C  UN0508              .....  1.3C......  .......................  None..........  62........  None.....   Forbidden   Forbidden  10
          Hydroxybenzotriazo
          le, anhydrous, dry
          or wetted with
          less than 20
          percent water, by
          mass.
         1-Hydroxybenzotriaz        4.1  UN3474                  I  4.1.......                      N90  None..........  211.......  None.....      0.5 kg      0.5 kg  D                 28, 36
          ole, monohydrate.
         Hydroxyl amine       Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          iodide.
         Hydroxylamine                8  UN2865                III  8.........       IB8, IP3, T1, TP33  154...........  213.......  240......       25 kg      100 kg  A            ...........
          sulfate.
         Hypochlorite                 8  UN1791                 II  8.........   A7, B2, B15, IB2, IP5,  154...........  202.......  242......         1 L        30 L  B                     26
          solutions.                                                                 N34, T7, TP2, TP24

[[Page 216]]

 
                                                               III  8.........  IB3, N34, T4, TP2, TP24  154...........  203.......  241......         5 L        60 L  B                     26
    G    Hypochlorites,             5.1  UN3212                 II  5.1.......  349, A9, IB8, IP2, IP4,  152...........  212.......  240......        5 kg       25 kg  D             4, 48, 52,
          inorganic, n.o.s.                                                                    T3, TP33                                                                                      56,
         Hyponitrous acid...  Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
         Igniter fuse, metal  .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          clad, see Fuse,
          igniter, tubular,
          metal clad.
         Igniters...........       1.1G  UN0121                 II  1.1G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Igniters...........       1.2G  UN0314                 II  1.2G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Igniters...........       1.3G  UN0315                 II  1.3G......  .......................  None..........  62........  None.....   Forbidden   Forbidden  07           ...........
         Igniters...........       1.4G  UN0325                 II  1.4G......  .......................  None..........  62........  None.....   Forbidden       75 kg  06           ...........
         Igniters...........       1.4S  UN0454                 II  1.4S......  .......................  None..........  62........  None.....       25 kg      100 kg  05           ...........
         3,3'-                        8  UN2269                III  8.........             IB3, T4, TP2  154...........  203.......  241......         5 L        60 L  A            ...........
          Iminodipropylamine.
    G    Infectious                 6.2  UN2900              .....  6.2.......                      A82  134...........  196.......  None.....    50 mL or    4 L or 4  B                     40
          substances,                                                                                                                                 50 g          kg
          affecting animals
          only.
    G    Infectious                 6.2  UN 2814             .....  6.2.......                      A82  134...........  196.......  None.....    50 mL or    4 L or 4  B                     40
          substances,                                                                                                                                 50 g          kg
          affecting humans.
         Inflammable, see     .........  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          Flammable.
         Initiating           Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          explosives (dry).
         Inositol             Forbidden  ..................  .....  ..........  .......................  ..............  ..........  .........  ..........  ..........  ...........  ...........
          hexanitrate (dry).
    G    Insecticide gases,         2.2  UN1968              .....  2.2.......  .......................  306...........  304.......  314, 315.       75 kg      150 kg  A            ...........
          n.o.s..
    G    Insecticide gases,         2.1  UN3354              .....  2.1.......                      T50  306...........  304.......  314, 315.   Forbidden      150 kg  D                     40
          flammable, n.o.s..
    G    Insecticide gases,         2.3  UN3355              .....  2.3, 2.1..                        1  None...