[Federal Register Volume 75, Number 168 (Tuesday, August 31, 2010)]
[Notices]
[Pages 53301-53303]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2010-21676]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
[FRL-9195-1]
Notice of a Regional Project Waiver of Section 1605 (Buy
American) of the American Recovery and Reinvestment Act of 2009 (ARRA)
to the Town of Sturbridge, MA
AGENCY: Environmental Protection Agency (EPA).
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: The EPA is hereby granting a waiver of the Buy America
requirements of ARRA Section 1605 under the authority of Section
1605(b)(2) [manufactured goods are not produced in the United States in
sufficient and reasonably available quantities and of a satisfactory
quality] to the Town of Sturbridge, Massachusetts (``Town'') for the
purchase of a foreign manufactured submersible mixer to be installed in
a new septage storage tank as part of a proposed wastewater treatment
plant upgrade. This is a project specific waiver and only applies to
the use of the specified product for the ARRA project being proposed.
Any other ARRA recipient that wishes to use the same product must apply
for a separate waiver based on project specific circumstances. Based
upon information submitted by Sturbridge and its consulting engineer,
it has been determined that there are currently no domestic
manufactured submersible mixers available to meet its proposed
technical project specifications. The Regional Administrator is making
this determination based on the review and recommendations of the
Municipal Assistance Unit. The Assistant Administrator of the Office of
Administration and Resources Management has concurred on this decision
to make an exception to Section 1605 of ARRA. This action permits the
purchase of a foreign manufactured submersible mixer by the Town of
Sturbridge, Massachusetts, as specified in its May 25, 2010 request.
DATES: Effective Date: August 19, 2010.
FOR FURTHER INFORMATION CONTACT: David Chin, Environmental Engineer,
(617) 918-1764, or Katie Connors, Environmental Engineer, (617) 918-
1658, Municipal Assistance Unit (CMU), Office of Ecosystem Protection
(OEP), U.S. EPA, 5 Post Office Square, Suite 100, Boston, MA 02109-
3912.
SUPPLEMENTARY INFORMATION: In accordance with ARRA Section 1605(b)(2)
and 1605(c), the EPA hereby provides notice that it is granting a
project waiver of the requirements of
[[Page 53302]]
Section 1605(a) of Public Law 111-5, Buy American requirements, to the
Town of Sturbridge, Massachusetts for the purchase of a non-domestic
manufactured submersible mixer, the Landia Model POPR-1 made in
Denmark, to be installed in a new septage storage tank to meet its
technical design specifications as part of its proposed wastewater
treatment plant upgrade.
EPA has determined that the Town's waiver request is late, but EPA
will evaluate the request as if it were timely made even though the
request was made after the construction contract was signed. Consistent
with the direction of the OMB Guidance at 2 CFR 176.120, EPA will
generally regard waiver requests with respect to components that were
specified in the bid solicitation or in a general/primary construction
contract as ``late'' if submitted after the contract date. However, in
this case EPA has determined that the Town's request, though made after
the date that the contract was signed, can be evaluated as timely
because a domestic submersible mixer meeting project specifications was
found to be unavailable by the contractor only after the shop drawings
had become available, which was after the contract date. The need for a
waiver was not determined until after the contractor had completed its
review and had confirmed that there were no domestic submersible mixers
available to meet project specifications. Accordingly, EPA will
evaluate the request as if it were timely made.
Section 1605 of the ARRA requires that none of the appropriated
funds may be used for the construction, alteration, maintenance, or
repair of a public building or a public works project unless all of the
iron, steel, and manufactured goods used in the project is produced in
the United States, or unless a waiver is provided to the recipient by
the head of the appropriate agency, here the EPA. A waiver may be
provided if EPA determines that (1) applying these requirements would
be inconsistent with the public interest; (2) iron, steel, and the
relevant manufactured goods are not produced in the United States in
sufficient and reasonably available quantities and of a satisfactory
quality; or (3) inclusion of iron, steel, and the relevant manufactured
goods produced in the United States will increase the cost of the
overall project by more than 25 percent.
The Town of Sturbridge is proposing a major upgrade to its existing
secondary treatment facility. It will include the construction of a new
headworks building; renovations to the existing process and filter
buildings; renovations to existing storage tanks and the construction
of new storage tanks; construction of new yard piping and conduit
systems; and other site improvements. The construction will take place
while the existing treatment facility remains fully operational. The
estimated cost of the entire wastewater treatment facility upgrade,
necessary to meet more stringent effluent limits in the future and to
accommodate expansion of the municipal sewer system, is approximately
$16M.
According to the Town's design engineer, the corrosive nature of
the septage and landfill leachate to be stored in the new septage
storage tank requires that the submersible mixer be constructed
entirely of stainless steel. Other prominent specifications require
that the mixer be equipped with a single planetary gear box with gear
reduction capability to provide increased longevity and efficiency for
the submersible mixer, and require that the mixer shaft be equipped
with a motor shaft sealing system comprised of three seals. Excerpts
from the submersible mixer specifications document provided by the
Town's design engineer include the following:
(1) Each mixer shall be of the integral-gear, close coupled,
submersible type with a maximum propeller speed of 390 rpm. All
components of the mixer, including the motor and gearbox, shall be
manufactured of solid AISI 316 acid-proof stainless steel and provide
continuous underwater operation while the mixer blades are completely
submerged. No stainless steel jackets that cover a cast iron housing
shall be allowed.
(2) Each mixer shall be provided with a grease chamber in the
propeller hub for the shaft sealing system, and a separate oil chamber
for the gearbox and mechanical seals. Drains and inspection plugs shall
be provided with positive anti-leak seals and shall be accessible from
the outside.
(3) Each mixer shall be provided with a sealing system consisting
of three seals separating the various parts. The outer seal in the
propeller hub shall be a lip seal with a stainless steel spring,
sealing the propeller shaft and hub grease chamber from the mixed
media, running on a stainless steel exchangeable wear bushing.
(4) The gearbox shall be a one-stage planetary reduction gear,
equipped with high precision, low-loaded gears designed for infinite
life and shall have a service factor of not less than 1.5.
The Town provided information on four domestic manufacturers of
submersible mixers and has determined that there are currently no
domestic manufacturers able to provide a submersible mixer that can
meet all of the project technical specifications. The Town also
identified a foreign manufacturer, Landia, Inc., in Denmark, which
produces a submersible mixer, Landia Model POPR-1. According to the
design engineer for the Town, it is the only submersible mixer that is
equipped with a gear reduction capability and is constructed entirely
of stainless steel-wetted parts meeting all project specifications. The
Town has requested a waiver for the Landia submersible mixer, Model
POPR-1, to be installed in the new septage storage tank.
An independent evaluation conducted by EPA's technical review team
supports and confirms the Town' claim that there are currently no
domestic manufacturers that can provide a submersible mixer to meet
project specifications. Research and follow-up communications between
EPA's national contractor and the four identified domestic
manufacturers confirmed that three do not manufacture gear driven
submersible mixers, and the fourth does not produce entirely stainless
steel mixers. Additional research conducted by EPA's national
contractor identified another domestic submersible mixer manufacturer.
However, it is not able to provide a submersible mixer that meets
project specifications. While this manufacturer claims that it plans to
produce a submersible mixer to meet project specifications by the
latter part of 2010, it does not currently do so.
The April 28, 2009 EPA HQ Memorandum, ``Implementation of Buy
American provisions of Public Law 111-5, the `American Recovery and
Reinvestment Act of 2009' '' (``Memorandum''), defines reasonably
available quantity as ``the quantity of iron, steel, or relevant
manufactured good is available or will be available at the time needed
and place needed, and in the proper form or specification as specified
in the project plans and design.'' The same Memorandum defines
``satisfactory quality'' as ``the quality of steel, iron or
manufactured good specified in the project plans and designs.''
Furthermore, the purpose of the ARRA is to stimulate economic
recovery by funding current infrastructure construction, not to delay
or curtail entirely projects that are ``shovel ready'' by requiring
potential SRF eligible recipients, such as the Town of Sturbridge, to
revise their design standards and specifications. To curtail entirely
this construction would directly
[[Page 53303]]
conflict with a fundamental economic purpose of ARRA, which is to
create or retain jobs.
The Municipal Assistance Unit (CMU) has reviewed this waiver
request and has determined that the supporting documentation provided
by Sturbridge establishes both a proper basis to specify a particular
manufactured good, and that the domestic manufactured goods that are
currently available do not meet the design specifications for the
proposed project. The information provided is sufficient to meet the
following criteria listed under Section 1605(b) of the ARRA and in the
April 28, 2009 Memorandum: Iron, steel, and the manufactured goods are
not produced in the United States in sufficient and reasonably
available quantities and of a satisfactory quality.
The March 31, 2009 Delegation of Authority Memorandum provided
Regional Administrators with temporary authority to issue exceptions to
Section 1605 of the ARRA within the geographic boundaries of their
respective regions and with respect to requests by individual grant
recipients.
Having established both a proper basis to specify the particular
good required for this project and that this manufactured good was not
available from a producer in the United States, the Town of Sturbridge,
Massachusetts is hereby granted a waiver from the Buy American
requirements of Section 1605(a) of Public Law 111-5. This waiver
permits use of ARRA funds for the purchase of a foreign manufactured
submersible mixer in Sturbridge's waiver request submittal dated May
25, 2010. This supplementary information constitutes the detailed
written justification required by Section 1605(c) for waivers based on
a finding under subsection (b).
Authority: Pub. L. 111-5, section 1605.
Dated: August 19, 2010.
Ira W. Leighton,
Acting Regional Administrator, EPA Region 1--New England.
[FR Doc. 2010-21676 Filed 8-30-10; 8:45 am]
BILLING CODE 6560-50-P