[Federal Register Volume 76, Number 55 (Tuesday, March 22, 2011)]
[Rules and Regulations]
[Pages 15798-15800]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-6618]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 25
[Docket No. NM428; Special Condition No. 25-417-SC]
Special Conditions: Boeing 747-468, Installation of a Medical
Lift
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final special conditions.
-----------------------------------------------------------------------
SUMMARY: These special conditions are issued for the Boeing 747-468
airplane. This airplane, as modified by Jet Aviation, will have a novel
or unusual design feature associated with the installation of a medical
lift. The applicable airworthiness regulations do not contain adequate
or appropriate safety standards for this design feature. These special
conditions contain the additional safety standards that the
Administrator considers necessary to establish a level of safety
equivalent to that established by the existing airworthiness standards.
DATES: Effective Date: March 22, 2011.
FOR FURTHER INFORMATION CONTACT: Jayson Claar, Transport Airplane
Directorate, Aircraft Certification Service, 1601 Lind Avenue, SW.,
Renton, Washington 98057-3356; telephone (425) 227-2194; fax (425) 227-
1149; e-mail jayson.claar@faa.gov.
SUPPLEMENTARY INFORMATION:
Background
On March 2, 2007, Jet Aviation Engineering Services L.P. (JAES), of
Teterboro, New Jersey, applied for a supplemental type certificate for
a reconfiguration of an aircraft interior in a 747-468. The Boeing
Model 747-468 airplane is FAA approved under Type Certificate A20WE as
a large transport-category airplane that is limited to 660 passengers
or fewer, depending on the interior configuration.
This modification includes the installation of a medical lift
between the main deck and upper deck. The lift allows the transport of
a single occupant between the decks during cruise or ramp operations.
The applicable airworthiness regulations do not contain adequate or
appropriate safety standards for this design feature.
Type Certification Basis
Under the provisions of Title 14, Code of Federal Regulations (14
CFR) 21.101, JAES must show that the 747-468, as changed, continues to
meet the applicable provisions of the regulations incorporated by
reference in Type Certificate A20WE, or of the applicable regulations
in effect on the date of application for the change. The regulations
incorporated by reference in the type certificate are commonly referred
to as the ``original type-certification basis.'' The regulations
incorporated by reference in Type Certificate A20WE are as follows:
Part 36, as amended by Amendments 36-1 through 36-15, and
any later amendments in existence at the time of certification.
Special Federal Aviation Regulation (SFAR) 27, as amended
by Amendments 27-1 through 27-6 and any later amendments in existence
at the time of type certification.
Part 25, effective February 1, 1965, as amended by
Amendments 25-1 through 25-59, and the part 25 section-number
exceptions itemized in Type Certificate A20WE.
The following special conditions, exemptions, and equivalent safety
findings, which are part of the Model 747-300 certification basis, are
also part of the certification basis for the Model 747-400.
The special conditions include those enclosed with an FAA letter to
The Boeing Company dated February 20, 1970, and the following:
1. Special Condition 4A, revised to apply to airplanes with the
landing-gear load-evener system deleted, was recorded as an enclosure
to an FAA letter to The Boeing Company dated May 12, 1971.
2. Special Condition No. 25-61-NW-1, for occupancy not to exceed 32
passengers on the upper deck of airplanes with a spiral staircase, was
transmitted to The Boeing Company by FAA letter dated February 26,
1975.
3. Special Condition No. 25-71-NW-3, for occupancy not to exceed 45
passengers on the upper deck of airplanes with a straight-segmented
stairway, was transmitted to The Boeing Company by FAA letter dated
September 8, 1976.
4. Modification of Special Condition No. 25-71-NW-3, for occupancy
not to exceed 110 passengers on the upper deck of airplanes with a
straight-segmented stairway, was transmitted to The Boeing Company by
FAA letter dated August 3, 1981.
5. Special Condition No. 25-77-NW-4, modification of the autopilot
system to approve the airplane for use of the system under Category
IIIb landing conditions, was transmitted to The Boeing Company by FAA
letter dated July 8, 1977.
6. Special Condition No. 25-ANM-16, for use of an overhead crew-
rest area, occupancy not to exceed ten crewmembers, was transmitted to
The Boeing Company by FAA letter dated November 19, 1987. The FAA-
approved procedures required for compliance with paragraph 13 of the
special condition are located in Boeing Document D926U303, Appendix D.
7. Special Condition no. 25-ANM-24, applicable to flight-deck
displays and propulsion-control systems, was provided to Boeing on
December 22, 1988.
8. Special Condition No. 25-ANM-25, which established lightning-
and radio-frequency-energy protection requirements, was provided to
Boeing on December 22, 1988.
Exemptions From Part 25
Exemption no. 1013A, dated December 24, 1969: Exemption from
Section 25.471(b) to allow lateral displacement of the center of
gravity from the airplane centerline.
The following optional requirements, which are part of the Model
747-300 certification basis, apply also to the 747-400:
Table 1--Optional Requirements
------------------------------------------------------------------------
Requirement Section
------------------------------------------------------------------------
Ditching provisions..................................... 25.801
Ice-protection provisions............................... 25.1419
------------------------------------------------------------------------
The following equivalent-safety findings, previously made for
earlier models under the provisions of
[[Page 15799]]
Sec. 21.21(b)(1), are also applicable to the Model 747-400:
Table 2--Equivalent-Safety Findings
------------------------------------------------------------------------
Requirement Section
------------------------------------------------------------------------
Width of aisle............... 25.815.
Pilot-compartment view....... 25.773.
Use of 1-g stall speed Several (747-400 only).
(nonstructural items).
Use of 1-g stall speed Several (747-400 only).
(structural items).
Position-light distribution 25.1389(b)(3) (747-400 only).
and intensities.
Fire-detection system........ 25.1203.\1\
Pressure relief.............. 25.1103(d).\1\
Emergency-locator transmitter 25.1415(d).
(ELT).
Emergency-exit marking....... 25.811(f).
------------------------------------------------------------------------
\1\ Applies to RB211-524G/H series engine installations only.
If the Administrator finds that the applicable airworthiness
regulations (i.e., 14 CFR part 25) do not contain adequate or
appropriate safety standards for the 747-468 because of a novel or
unusual design feature, special conditions are prescribed under the
provisions of Sec. 21.16.
In addition to the applicable airworthiness regulations and special
conditions, the 747-468 must comply with the fuel-vent and exhaust-
emission requirements of 14 CFR part 34, and the noise certification
requirements of 14 CFR part 36.
The FAA issues special conditions, as defined in 14 CFR 11.19, in
accordance with Sec. 11.38, and they become part of the type-
certification basis under Sec. 21.101.
Special conditions are initially applicable to the model for which
they are issued. Should the applicant apply for a supplemental type
certificate to modify any other model included on the same type
certificate to incorporate the same or similar novel or unusual design
feature, the special conditions would also apply to the other model
under Sec. 21.101.
Novel or Unusual Design Features
The original aircraft configuration included a straight stairway
between the main deck and upper deck at Fuselage Station 870. The
stairway is relocated in the new configuration, and the existing
stairway is replaced with an electrically powered medical lift using
the opening in the upper deck formerly occupied by the stairs. When the
lift is not in operation, the upper-deck opening is covered by floor
panels. These floor panels are opened up prior to operation of the lift
and form a protective fencing around the upper-deck opening.
The purpose of the medical lift is to move an occupant between the
master lounge in the upper deck and the medical room on the lower deck.
The lift platform is driven by two redundant electrical motors,
mounted to the rear wall, between the struts. A lifting gear-drive with
shafts and gear boxes is powered on the front and rear of the lift
platform. The spindles are supported at the lifting gear on the lower
support structure and with a strut support on the upper deck. The lift
platform is guided in lateral directions with the guiding rails mounted
on the struts.
Discussion
Due to the novel or unusual features associated with the
installation of this medical lift, the following special conditions are
considered necessary to provide a level of safety equal to that
established by the airworthiness regulations incorporated by reference
in the type-certificate.
Discussion of Comments
Notice of proposed special conditions no. 25-99-11-SC for the
Boeing Model 747-468 airplane was published in the Federal Register on
May 18, 2010 (75 FR 27662). No public comments were received and the
special conditions are adopted as proposed.
After the public-comment deadline on June 17, 2010, the FAA added
text referenced in Note 1 in Table 2, and added special conditions 14e
and f, and additional text to special condition 15a. The FAA has
determined that this additional information enhances, and does not
compromise, safety; does not materially affect the intent of the
special conditions upon which the pubic had opportunity to comment; and
therefore does not warrant a second public-comment period.
Applicability
As discussed above, these special conditions are applicable to the
747-468. Should JAES apply at a later date for a supplemental type
certificate to modify any other model included on Type Certificate
A20WE, to incorporate the same novel or unusual design feature, the
special conditions would apply to that model as well.
Conclusion
This action affects only certain novel or unusual design features
on one model of airplanes. It is not a rule of general applicability
and it affects only the applicant who applied to the FAA for approval
of these features on the airplane.
List of Subjects in 14 CFR Part 25
Aircraft, Aviation safety, Reporting and recordkeeping
requirements.
The authority citation for these special conditions is as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704.
The Special Conditions
Accordingly, pursuant to the authority delegated to me by the
Administrator, the following special conditions are issued as part of
the type-certification basis for Boeing 747-468 airplanes modified by
JAES.
1. A functional verification must be conducted to ensure the
adequacy of the lift design features that are supposed to prevent
injury to the lift occupant, lift operator, and lift observer.
2. The occupied lift must be designed to withstand the non-
emergency load conditions imposed by the aircraft according to loads
report SIE-327-301, revision D.
3. Occupancy or operation of the lift must not be permitted during
taxi, takeoff, landing (TTL), or turbulent conditions.
4. The lift must be stowed for TTL. The stowed position requires
the lift platform positioned at the main-deck level with the floor
panels closed.
5. A portable oxygen bottle must be present in the lift and easily
accessible to the occupant.
[[Page 15800]]
6. Occupancy of the lift must be limited to a single occupant
secured in one of two possible configurations:
a. The occupant must be secured to a medical stretcher that is
attached to the lift platform. The occupied stretcher must be designed
to withstand the non-emergency load conditions defined in loads report
SIE-327-301, revision D.
b. The occupant must be secured to a wheelchair that is attached to
the lift platform.
7. Control panels must be located on both main and upper decks,
connected with full duplex audio communications. On both operator
control units, an emergency shut-off switch must be installed. In an
emergency, this switch must immediately interrupt the main power supply
to the motors. Lift operation must be stopped until the emergency shut-
off switch is reset. As soon as one of the operators commands operation
in a direction, the ``Up'' and ``Down'' option buttons must be disabled
and the stop button enabled. Before one of the operators is able to
change the lift-travel direction again, the lift must first be stopped.
8. Lift operation must require a trained operator at the main-deck
control panel and a trained observer at the upper-deck control panel.
9. Sensors must be installed to detect the following conditions,
and to prevent the start or continuation of lift travel if any
conditions are not met:
a. Upper-deck seat, located on the left side of the aircraft and
just forward of the master-bath bulkhead, is in its most forward,
outboard position.
b. Upper-deck master-bedroom/lavatory port bulkhead is opened and
secured.
c. Upper-deck shower door is closed and secured.
d. Upper-deck master-lavatory door is opened and secured.
e. Upper-deck floor panels are opened and configured to form the
protective fencing.
f. Main-deck inboard doors are closed and secured. The doors must
be lockable only from the outside of the lift. This ensures that the
operator has control of this area and that nobody is located under the
lift.
g. Aircraft seat-belt-fasten signs must not be illuminated.
10. Sensors must be installed to detect the following conditions
during operation, and to prevent continued lift travel if any of these
conditions occur:
a. Over-temperature of lift motors and/or power-frequency
converter.
b. Presence of smoke at motors and in electrical-control cabinet.
c. Over-current at the lift motors.
d. Asynchronous operation of the spindles.
11. A built-in fire extinguisher must be installed in the motor and
electrical-control cabinet. This fire extinguisher must be designed to
discharge automatically upon the occurrence of a fire.
12. The lift must have the provision for manual operation in the
event of a malfunction such as a loss of power to the lift and/or
associated systems.
13. A separate battery backup system must provide lighting for the
lift-control system, lift control/sensors, communication system, and
lift lights for a minimum of 10 minutes in the event of loss of power
to the lift and/or associated systems.
14. Lift placards must be installed near or adjacent the control
panels identified in special condition 7. The placards must be stated
as follows:
a. THIS LIFT IS APPROVED FOR MOVING ONLY A SINGLE OCCUPANT BETWEEN
THE MAIN AND UPPER DECKS AND ONLY WHEN SECURED TO EITHER AN APPROVED
MEDICAL STRETCHER OR WHEELCHAIR. NO OTHER USES OF THIS LIFT ARE
APPROVED.
b. DO NOT OPERATE LIFT DURING TAXI, TAKEOFF, LANDING, OR
TURBULENCE.
c. AN APPROVED MEDICAL STRETCHER OR WHEELCHAIR MUST BE PROPERLY
SECURED TO THE LIFT PLATFORM BEFORE OPERATING THIS LIFT.
d. THE LIFT MUST BE STOWED FOR TAXI, TAKEOFF, AND LANDING. THE
STOWED POSITION REQUIRES THE LIFT PLATFORM POSITIONED AT THE MAIN-DECK
LEVEL WITH THE FLOOR PANELS CLOSED.
e. DURING MEDICAL-STRETCHER TRANSPORT, ALL PERSONNEL, MATERIEL, AND
PATIENT EXTREMETIES MUST BE POSITIONED BETWEEN THE HEAD AND FOOT OF THE
STRETCHER.
f. LIFT MAXIMUM CAPACITY: X LBS (X KG)
15. Lift operational-instruction placards must be installed near
the control panels and must describe how to:
a. Configure the lift for operation, including ensuring that the
bottom of the lift is clear of personnel and materiel before lowering
the lift from the upper deck.
b. Operate the lift.
c. Stow the lift for non-operation such as during TTL and
turbulence.
d. Operate the mechanical-override features in the event of a
malfunction such as a loss of power to the lift and/or associated
systems.
16. Training and related manuals must include:
a. Limitations and procedures for normal lift operation.
b. Backup and override procedure for evacuating the lift and
returning it to TTL configuration.
17. Special conditions nos. 3, 4, and 14 must be documented in the
Limitations section of the airplane flight manual.
Issued in Renton, Washington, on February 3, 2011.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2011-6618 Filed 3-21-11; 8:45 am]
BILLING CODE 4910-13-P