[Federal Register Volume 76, Number 169 (Wednesday, August 31, 2011)]
[Proposed Rules]
[Pages 54156-54162]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2011-22006]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Highway Administration

23 CFR Part 655

[FHWA Docket No. FHWA-2010-0159]
RIN 2125-AF43


National Standards for Traffic Control Devices; the Manual on 
Uniform Traffic Control Devices for Streets and Highways; Revision

AGENCY: Federal Highway Administration (FHWA), Department of 
Transportation (DOT).

ACTION: Notice of proposed amendments; request for comments.

-----------------------------------------------------------------------

SUMMARY: The MUTCD is incorporated in our regulations, approved by the 
Federal Highway Administration, and recognized as the national standard 
for traffic control devices used on all streets, highways, bikeways, 
and private roads open to public travel. The FHWA proposes to revise 
certain information relating to target compliance dates for traffic 
control devices. Consistent with Executive Order 13563, and in 
particular its emphasis on burden-reduction and on retrospective 
analysis of existing rules, the proposed changes are intended to reduce 
the costs and impacts of compliance dates on State and local highway 
agencies and to streamline and simplify the information.

DATES: Comments must be received on or before October 31, 2011. Late 
comments will be considered to the extent practicable.

ADDRESSES: Mail or hand deliver comments to the U.S. Department of 
Transportation, Dockets Management Facility, 1200 New Jersey Avenue, 
SE., Washington, DC 20590, or submit electronically at http://www.regulations.gov or fax comments to (202) 493-2251. All comments 
should include the docket number that appears in the heading of this 
document. All comments received will be available for examination and 
copying at the above address from 9 a.m. to 5 p.m., E.T., Monday 
through Friday, except Federal holidays. Those desiring notification of 
receipt of comments must include a self-addressed, stamped postcard or 
may print the acknowledgment page that appears after submitting 
comments electronically. Anyone is able to search the electronic form 
of all comments received into any of our dockets by the name of the 
individual submitting the comment (or signing the comment, if submitted 
on behalf of an association, business, labor union, etc.). You may 
review DOT's complete Privacy Act Statement in the Federal Register 
published on April 11, 2000 (Volume 65, Number 70, Page 19477-78) or 
you may visit http://dms.dot.gov.

FOR FURTHER INFORMATION CONTACT: Mr. Hari Kalla, Office of 
Transportation Operations, (202) 366-5915; or Mr. William Winne, Office 
of the Chief Counsel, (202) 366-1397, Federal Highway Administration, 
1200 New Jersey Ave., SE., Washington, DC 20590. Office hours are from 
8 a.m. to 4:30 p.m., E.T., Monday through Friday, except Federal 
holidays.

SUPPLEMENTARY INFORMATION: 

Electronic Access and Filing

    This document, the notice of and request for comments, and all 
comments received may be viewed online through the Federal eRulemaking 
portal at http://www.regulations.gov. Electronic submission and 
retrieval help and guidelines are available under the help section of 
the Web site. It is available 24 hours each day, 365 days each year. 
Please follow the instructions. An electronic copy of this document may 
also be downloaded from the Office of the Federal Register's home page 
at: http://www.archives.gov and the Government Printing Office's Web 
page at: http://www.access.gpo.gov/nara.
    To help make the FHWA's docket comment review process more 
efficient, the FHWA requests that commenters cite the Section number 
identified in Table I-2 for any comment to the docket about a specific 
proposed revision to the text of the table.

Background

    When new provisions are adopted in a new edition or revision of the 
MUTCD, any new or reconstructed traffic control devices installed after 
adoption are required to be in compliance with the new provisions. For 
existing devices in the field that do not comply with the new MUTCD 
provisions, 23 CFR 655.603(d)(1), authorizes the FHWA to establish 
target compliance dates for compliance of particular existing devices. 
Table I-2 in the Introduction of the 2009 edition of the MUTCD lists 58 
specific provisions for which the FHWA has established target 
compliance dates for upgrading existing devices in the field via the 
Federal rulemaking process in Final Rules issued in 2000,\1\ 2003,\2\ 
2007,\3\ and 2009.\4\
---------------------------------------------------------------------------

    \1\ 65 FR 78923, December 18, 2000.
    \2\ 68 FR 65496, November 20, 2003.
    \3\ 72 FR 72574, December 21, 2007.
    \4\ 74 FR 66732, December 16, 2009.
---------------------------------------------------------------------------

    In the absence of a specific target compliance date, existing 
devices in the

[[Page 54157]]

field that do not meet the new MUTCD provisions are expected to be 
upgraded by highway agencies over time to meet the new provisions via a 
systematic upgrading process as required by 23 CFR 655.603(d)(1), but 
there are no specific dates for required completion of the upgrades. 
Systematic upgrading programs enable highway agencies to prioritize 
traffic control upgrades based on a variety of factors such as relative 
safety needs, costs, and available resources. Agencies can decide, 
where appropriate, to defer upgrading certain non-compliant devices 
until the device wears out, is damaged or destroyed, or is replaced.
    In response to concerns about the potential costs and impact of 
previously adopted MUTCD compliance dates on State and local 
governments in the current economic climate, on November 30, 2010, the 
FHWA published in the Federal Register a Request for Comments \5\ on 
traffic control device compliance dates. The FHWA asked for responses 
to a series of seven questions about compliance dates, their benefits 
and potential economic impacts, especially economic hardships to State 
and local governments that might result from specific target compliance 
dates for upgrading certain non-compliant existing devices.
---------------------------------------------------------------------------

    \5\ 75 FR 74128, November 30, 2010.
---------------------------------------------------------------------------

    By the end of the comment period, the FHWA received 592 letters to 
the docket. The comments were submitted by 360 private citizens, 168 
local government highway agencies, 28 State DOTs, 16 industry 
representatives, 6 national associations representing practitioners, 5 
national associations representing safety advocates, 5 elected 
officials, and 4 traffic engineering consultants.
    The overwhelming majority of comments from all responders addressed 
the target compliance dates associated with maintaining minimum levels 
of sign retroreflectivity and with minimum letter heights for street 
name signs. There were also many comments from private citizens 
expressing concerns about requiring the use of mixed-case lettering for 
street name signs and other guide signs.
    Comments from private citizens were evenly balanced between support 
for and opposition to compliance dates for upgrading existing signs 
that do not meet minimum levels of retroreflectivity. Often emphasizing 
the current economic climate, local highway agencies predominantly 
expressed concerns about the target compliance dates for sign 
retroreflectivity because of economic concerns. Similarly, State DOTs 
and national associations representing practitioners generally 
suggested that all dates should be eliminated or extended because of 
current economic conditions. Representatives of the traffic control 
materials industry and national safety associations supported retaining 
all existing compliance dates for safety reasons, often specifically 
citing concerns about the needs of older road users. Also, a variety of 
comments indicated confusion about target compliance dates in general 
and that the number and complexity of compliance dates listed in Table 
I-2 makes it difficult for agencies to understand what is required in 
order to take appropriate actions.
    In general, the FHWA has intended that target compliance dates 
coincide with the useful service life of the devices that would need to 
be replaced to meet any new requirements, thus minimizing economic and 
logistical impacts on highway agencies. This approach is consistent 
with Executive Order 13563 and in particular its emphasis on the 
avoidance of unjustified costs. Some comments indicated that variations 
in climate and other environmental conditions around the country may 
result in considerably longer useful service lives of certain devices 
than the estimates used by the FHWA in establishing the compliance 
dates. In such cases, compliance dates can create an undue burden for 
the agency, requiring device replacement before the end of actual 
useful service life.
    The FHWA has carefully reviewed and considered all of the comments 
received in response to the request for comments. It has decided to 
propose revisions to Table I-2 to simplify it and reduce the impacts of 
target compliance dates on agencies by eliminating, extending, or 
otherwise revising most of the dates. This approach is consistent with 
the requirements of Executive Order 13563, including its emphasis on 
consideration of benefits and costs (sections 1(a) and 1(b)), its 
requirement of an open exchange of information with stakeholders 
(section 2(a)), and, in particular, its call for retrospective analysis 
of existing rules, including streamlining and modification to make such 
rules less burdensome (section 6). This approach is also consistent 
with Presidential Memorandum, Administrative Flexibility, which calls 
for reducing burdens and promoting flexibility for State and local 
governments.

Proposed Amendment

    Of the 58 items for which target compliance dates are currently 
listed in Table I-2, the FHWA proposes to eliminate altogether the 
compliance dates for 46 items (8 that have already expired and 38 that 
have future compliance dates) and to extend and/or revise the dates for 
4 items. We are not proposing a change for the dates for the other 
eight items, which actually represent only six specific requirements in 
the MUTCD, since three of the eight items are all related to the 
required use of high-visibility apparel by workers in the right-of-way. 
For these six requirements, the compliance dates would remain in 
effect.
    A summary of the specific proposed changes in Table I-2 of the 
MUTCD is included in the following section.
    The text of this proposed revision to the 2009 edition of the MUTCD 
is available for inspection and copying, as prescribed in 49 CFR part 
7, at the FHWA Office of Transportation Operations (HOTO-1), 1200 New 
Jersey Avenue, SE., Washington, DC 20590. Furthermore, the text of the 
proposed revision is available on the MUTCD Internet Web site http://mutcd.fhwa.dot.gov and on the docket for this rulemaking at http://www.regulations.gov. The proposed text is available in two formats. The 
first format shows the current MUTCD text of Table I-2 with proposed 
additions in blue, underlined text and proposed deletions as red 
strikeout text. The second format shows a ``clean'' version of Table I-
2, with all the proposed changes incorporated. The complete 2009 
edition of the MUTCD is also available on the same Internet Web site.
    This NPA is being issued to provide an opportunity for public 
comment on the desirability of these proposed amendments to the MUTCD. 
The FHWA is interested in receiving comments regarding the safety 
benefits provided by traffic device uniformity, the costs and other 
burdens associated with achieving compliance for existing non-compliant 
devices, and the proposed revisions, extensions, eliminations, and 
retention of compliance dates outlined in this notice. In all cases, 
and consistent with Executive Order 13563, section 2, the FHWA seeks 
comments not only on its proposals but also on possible alternative 
approaches. Based on the comments received and its own experience, the 
FHWA may issue a Final Rule concerning the proposed changes included in 
this notice.

[[Page 54158]]

Discussion of Proposed Amendments to Table I-2
    1. The FHWA proposes to eliminate target compliance dates, which 
were based on estimated useful service lives, for 33 items in Table I-2 
that were established in the Final Rules for the 2000 and 2003 editions 
of the MUTCD, that have not yet expired. These 33 target compliance 
dates proposed for elimination are for provisions in Sections 2B.03, 
2B.10, 2B.11, 2B.13, 2B.26, 2B.55, 2C.04, 2C.13, 2C.20, 2C.38, 2C.40, 
2C.41, 2C.42, 2C.46, 2C.49, 2C.61, 2C.63, 2D.43 (two provisions), 
2D.44, 2G.01 through 2G.07, 2G.11 through 2G.15, 2H.05 and 2H.06, 
2I.09, 2I.10, 2N.03, 3B.18, 4D.01, 4D.31, 4E.07, 5C.05, 7B.16, and 
8C.09. These items mostly involve new or revised sign designs, 
including larger letter heights and/or larger sizes for some signs, and 
certain other changes in traffic control device design, location, or 
operation that have made some existing devices in the field obsolete. 
Based on comments received and other communications with State and 
local highway agencies, the FHWA believes that these 33 dates in Table 
I-2 may create fiscal and logistical burdens on highway agencies. Based 
on comments received, the FHWA believes that agencies can better 
organize and track the replacement or upgrade of these devices in the 
ordinary course of implementation of their systematic upgrading 
programs. Additionally, highway agencies are in the best position to 
make decisions on device replacements based on actual useful service 
lives in their particular climates and environments, rather than having 
a universal compliance date based on estimated useful service life. The 
FHWA requests comments on the safety benefits, the costs, and other 
burdens associated with achieving compliance for existing non-compliant 
devices, and the proposed elimination of these compliance dates. The 
FHWA also requests comments on alternative approaches, such as 
extending rather than eliminating these compliance dates.
    2. The FHWA proposes to eliminate the target compliance dates for 
three items in Table I-2 that were established with the Final Rule for 
the 2009 edition of the MUTCD. Although these dates were recently 
established, the FHWA believes their elimination is warranted based on 
consideration of specific concerns raised in responses to the November 
30, 2010, Request for Comments, as explained below. For each of these 
three items, the FHWA requests comments on the safety benefits, the 
costs, and other burdens associated with achieving compliance for these 
existing non-compliant devices, and the proposed elimination of these 
compliance dates.
    The December 31, 2019, target compliance date would be eliminated 
for a provision in Section 2D.45 that requires multilane conventional 
road approaches to interchanges to have guide signs to identify which 
direction of turn is necessary for access to each direction of the 
freeway or expressway. Agencies expressed confusion about this date 
because they interpreted it as requiring the replacement of existing 
overhead sign structures (which typically have a very long useful 
service life, well beyond 10 years) in order to install the required 
new signs. The MUTCD allows post-mounted signs to be used to provide 
the needed information to road users about turn directions at the 
interchange, even if overhead sign structures are present for other 
signs. The FHWA believes that eliminating this target compliance date 
will reduce the confusion. Highway agencies will still need to install 
the required signs under their systematic upgrading programs, but will 
not have a specific date by which this must be accomplished.
    The target compliance date of December 31, 2016, or at resurfacing, 
whichever comes first, would be eliminated for provisions in Sections 
3B.04 and 3B.05 that require dotted, rather than broken, lane lines for 
dropped lanes and for acceleration, deceleration, and auxiliary lanes. 
Some agencies indicated that they have durable markings for lane lines 
that have a useful service life that will extend beyond the 2016 date. 
Some agencies also use recessed or inlaid markings, for which it is not 
practical to change the marking pattern from broken to dotted until the 
next resurfacing occurs, but resource constraints will cause the 
resurfacing cycle to exceed 7 years. Some agencies also indicated it 
would be very difficult to meet the 2016 compliance date because of the 
large number of individual pavement marking layout drawings for 
individual existing intersections and interchanges that need to be 
revised to show the locations and lengths of dotted lane lines before 
crews can be instructed to revise the markings in the field. 
Eliminating this target compliance date would allow agencies to 
implement the new marking requirement when existing lines become 
significantly worn to the point they can be marked over without causing 
road user confusion, or when resurfacing occurs.
    The December 31, 2014, target compliance date for the provision in 
Section 8C.12 that requires a traffic queuing study of grade crossings 
within 200 feet of roundabouts or other circular intersections would be 
eliminated. Based on knowledge gained from frequent interactions with 
State and local agencies, the FHWA believes that there are extremely 
few existing roundabouts or other circular intersections within 200 
feet of a grade crossing and that those that do exist have likely 
already been studied for queuing issues as a part of or subsequent to 
their original design. As roundabouts are increasingly being given 
consideration as an alternative to installing a traffic signal, any 
such considerations at locations near grade crossings will be required 
by the language in Section 8C.12 to be studied as a part of the process 
of evaluating whether to construct a roundabout.
    The FHWA requests comments on the safety benefits, the costs, and 
other burdens associated with the proposed elimination of these 
compliance dates. The FHWA also requests comments on alternative 
approaches, such as extending rather than eliminating these compliance 
dates.
    3. The FHWA proposes to eliminate from Table I-2 eight items for 
which the previously established target compliance dates have expired. 
These dates (pertaining to certain provisions in Sections 2B.09, 2C.30, 
2C.50, 2J.05, 7B.11, 7B.12, 8B.19 and 8C.02 through 8C.05, and 9B.18) 
were established in the Final Rules for the 2000 and 2003 editions of 
the MUTCD. Elimination of these items from the table is consistent with 
the FHWA's previous practice of eliminating target compliance dates 
from subsequent MUTCD editions after they have expired. Based on 
frequent communications and interactions with numerous State and local 
highway agencies, the FHWA believes that most agencies have already 
upgraded these devices as their useful service lives have been reached. 
Although some of these non-compliant devices might still exist in the 
field, they are expected to be replaced with compliant devices under 
agencies' systematic upgrading programs. The FHWA requests comments on 
this proposal.
    4. The FHWA proposes to revise the January 22, 2012, target 
compliance date that was established in December 2007, with the Final 
Rule for Revision 2 of the 2003 edition of the MUTCD, for the Section 
2A.08 provision that requires agencies to implement an assessment or 
management method designed to maintain sign retroreflectivity at or 
above the established minimum levels.

[[Page 54159]]

This compliance date does not require any signs to be replaced by a 
given date. It requires highway agencies to implement an assessment or 
management method for maintaining sign retroreflectivity by the 
compliance date in accordance with section 406 of the Department of 
Transportation and Related Agencies Appropriations Act, 1993 (Pub. L. 
102-388; October 6, 1992). The compliance date for this requirement 
would be extended to a date 2 years after the effective date of the 
Final Rule for this proposed revision of the MUTCD. This would provide 
agencies with an estimated additional 1 to 2 years to implement their 
chosen assessment or management method. Additionally, the FHWA proposes 
to make the new compliance date apply only to implementing an 
assessment or management method for regulatory and warning signs. The 
requirement in the MUTCD language to implement a method for all types 
of signs would remain, but there would not be a specific target 
compliance date for required implementation of the method for signs 
other than regulatory and warning signs. Based on our subject matter 
expertise and experience with the benefits and impacts of traffic 
control devices, the FHWA believes that, because of the critical safety 
nature of the messages they convey, especially for older road users, 
regulatory and warning signs constitute the highest priority for 
assessing retroreflectivity of existing signs. The proposed revisions 
to the compliance date and its applicability will provide relief and 
enable agencies to determine when their resources will allow them to 
add signs other than regulatory and warning signs to their 
retroreflectivity assessment or management method.
    Additionally, the FHWA proposes to eliminate the two existing 
target compliance dates for replacement of signs that are identified 
using the assessment or management method as failing to meet the 
established minimum retroreflectivity levels. The January 22, 2015, 
date for regulatory, warning, and post-mounted guide (except street 
name) signs and the January 22, 2018, date for street name signs and 
overhead guide signs would both be eliminated. Without specific 
compliance dates for these items, agencies will still need to replace 
any sign they identify as not meeting the established minimum 
retroreflectivity levels.
    The FHWA requests comments on the safety benefits, the costs, and 
other burdens associated with achieving compliance with this 
requirement, and the proposed revisions of these compliance dates. The 
FHWA also requests comments on alternative approaches, including 
retention of the current compliance dates and extending rather than 
eliminating some of them.
    5. The FHWA proposes to revise the target compliance date of 
December 31, 2014, or when timing adjustments are made to the 
individual intersection and/or corridor, whichever occurs first, that 
applies to provisions on timing requirements for vehicular yellow and 
red clearance intervals in Section 4D.26 and pedestrian clearance 
intervals in Section 4E.06. These compliance dates were established 
with the Final Rule for the 2009 edition of the MUTCD. As noted in that 
Final Rule, the compliance dates were established to achieve a more 
rapid implementation of these new requirements at existing locations, 
because safety studies found that significant crash reductions were 
achieved where the required timing methods were used to determine the 
yellow and red clearance intervals, and because the FHWA believes that 
the new requirements for pedestrian clearance intervals are needed to 
provide a buffer between pedestrian movements and vehicular movements. 
The compliance dates were based on what FHWA believed to be the typical 
signal retiming frequency of about 5 years. Some agencies commented 
that current budgetary constraints have made it difficult to retime all 
of their traffic signals on a 5-year cycle. The FHWA proposes to extend 
the existing compliance date to a date of 5 years after the effective 
date of the Final Rule for this proposed revision of the MUTCD, or when 
timing adjustments are made to the individual intersection and/or 
corridor, whichever occurs first. This would provide agencies with an 
estimated additional 2 years to implement the new requirements of 
Sections 4D.26 and 4E.06 at any locations that have not already been 
made compliant under a previous intersection or corridor retiming.
    The FHWA requests comments on the safety benefits, the costs, and 
other burdens associated with achieving compliance for these existing 
non-compliant devices, and the proposed revision of this compliance 
date. The FHWA also requests comments on alternative approaches, 
including retention of the current compliance dates and extending them 
for a longer period.
    6. The FHWA proposes to revise and extend the compliance date for 
the provisions in Sections 8B.03 and 8B.04 that require a 
retroreflective strip on the back of Crossbuck signs and on the front 
and back of supports for Crossbuck signs at passive grade crossings. 
The existing compliance date of January 17, 2011, was established with 
the Final Rule for the 2000 edition of the MUTCD. The 2003 edition of 
the MUTCD eliminated the requirement to install the retroreflective 
strips on the fronts of Crossbuck sign supports, if a Yield or Stop 
sign is present along with the Crossbuck sign. During the last decade, 
the FHWA was considering establishing requirements to add a Yield or 
Stop sign at all passive railroad crossings. The addition of a Yield or 
Stop sign could necessitate replacing the Crossbuck support post in 
order to achieve minimum mounting heights. As a result, many railroad 
companies and highway agencies have deferred installing the 
retroreflective strips until a final decision was made on this issue in 
order to avoid unnecessary expense and to achieve the economies of 
sending sign crews to crossings only once rather than twice. The 
December 2009 Final Rule for the 2009 MUTCD did incorporate the 
requirement for YIELD or STOP signs at passive crossings in Section 
8B.04, and a target compliance date for adding these signs at existing 
crossings was established as December 31, 2019. The January 12, 2011, 
compliance date for the retroreflective strips provided railroads and 
public agencies with only 1 year after the final decision on the rule 
for Yield or Stop signs to install the retroreflective strips at the 
thousands of crossings where such work was deferred.
    The FHWA proposes to extend the target compliance date for the 
retroreflective strips to December 31, 2019, to coincide with the date 
for adding Yield or Stop signs with Crossbuck signs at passive grade 
crossings. As noted in the Final Rule that established the target 
compliance date for the retroreflective strips, the addition of such 
strips provides safety benefits that justify having a target compliance 
date, but having a single compliance date for both the retroreflective 
strips and the Yield or Stop signs at grade crossings is more 
practical. The FHWA also proposes to adjust the item for Section 8B.03 
in Table I-2 to more accurately reflect that the requirements for 
retroreflective strips are in Section 8B.04 as well as in Section 8B.03 
and to accurately reflect that the compliance date was also intended to 
apply to the retroreflective strips on the backs of the Crossbuck 
signs.
    The FHWA requests comments on the safety benefits, the costs, and 
other burdens associated with achieving compliance for these existing 
non-compliant devices, and the proposed revision of this compliance 
date. The

[[Page 54160]]

FHWA also requests comments on alternative approaches, including 
retention of the current compliance dates and extending them for a 
longer period.
    7. The FHWA proposes to retain the existing target compliance dates 
in Table I-2 for eight items that we deem to be of critical safety 
importance, based on existing evidence and our subject matter expertise 
and experience in traffic control device matters. For each of these 
eight items, the Final Rules establishing the compliance dates clearly 
identified the safety justification for such compliance dates. These 
justifications remain valid, as summarized below. For each of these 
eight items, the FHWA requests comments on the safety benefits, the 
costs, and other burdens associated with achieving compliance for these 
existing non-compliant devices, and the proposed retention of this 
compliance date. The FHWA also requests comments on alternative 
approaches, including extension of the current compliance dates.
    The January 17, 2013, compliance date for Section 2A.19 provisions 
requiring crashworthiness of existing sign supports on roads with 
posted speed limits of 50 mph or higher was established in the Final 
Rule for the 2003 edition of the MUTCD to be consistent with 
information previously communicated to jurisdictions in a variety of 
training and presentations by the FHWA Office of Safety regarding 
roadside safety and countermeasures for run-off-the-road crashes. 
Eliminating fixed-object hazards such as non-crashworthy sign supports 
on high-speed roads remains a critical safety need due to the deaths 
and severe injuries that high-speed run-off-the-road crashes can result 
in when a non-crashworthy sign support is struck. Therefore, the 10-
year period for compliance from the 2003 Final Rule is proposed to be 
retained.
    The Final Rule for the 2009 edition of the MUTCD established new 
requirements in Section 2B.40 to install additional One Way signs at 
certain types of intersections and established a December 31, 2019, 
compliance date for adding the required signs at existing intersections 
where the signs are not in place in the required number and location. 
This 10-year period was established because of the demonstrated safety 
issues associated with wrong-way travel on divided highways, research 
on the needs of older drivers, and because the additional signs would 
provide significant safety benefits to road users. These safety 
benefits justify retaining the existing compliance date for installing 
the critically-needed One Way signs at existing intersections.
    In Sections 2C.06 through 2C.14, revised requirements on the use of 
various horizontal alignment warning signs and determinations of 
advisory speed values were adopted in the Final Rule for the 2009 
edition of the MUTCD and a compliance date of December 31, 2019, was 
established for any required revisions in posted advisory speeds and 
for installing any newly-required horizontal alignment warning signs 
that are not currently in place at existing curves. This 10-year 
compliance date was established because of the demonstrated safety 
issues associated with run-off-the-road crashes at horizontal curves. 
Fatalities at horizontal curves account for approximately 25 percent of 
all highway fatalities, yet horizontal curves are only a small portion 
of the Nation's highway mileage. The more rational and uniform posting 
of advisory speeds and the installation of the required additional 
horizontal alignment warning signs at existing locations will provide 
significant safety benefits to road users and a 10-year period for 
achieving compliance is remains appropriate.
    The Final Rule for the 2009 edition of the MUTCD established new 
requirements in Sections 2E.31, 2E.33, and 2E.36 for the use of black-
on-yellow ``Left'' or ``Left Exit'' plaques on guide signs for all 
left-hand freeway and expressway exits and established a compliance 
date of December 31, 2014, for adding such plaques to existing guide 
signs. This 5-year target compliance date was established to address a 
recommendation of the National Transportation Safety Board as a result 
of a significant safety concern exhibited with left-hand exits. The 
installation of these plaques at all existing left-hand exits within 5 
years is necessary to achieve critical safety improvements for road 
users at left-side exits. The installation of these plaques generally 
does not require replacement of the existing sign or sign supports and 
this change affects relatively few existing locations throughout the 
country.
    The Final Rule for the 2009 edition of the MUTCD also established 
new requirements in Sections 6D.03, 6E.02, and 7D.04 that all workers, 
including flaggers and school crossing guards, within the right-of-way 
of all highways, not just Federal-aid highways, must wear high-
visibility apparel, and established a 2-year target compliance date of 
December 31, 2011. Required compliance of apparel for workers, 
including law enforcement officers, on Federal-aid highways has been in 
effect since November 24, 2008. The 2-year target compliance date for 
these three provisions applicable to non-Federal-aid highways was 
established to be consistent with the 2-year compliance period that was 
previously established for workers on Federal-aid highways. The 
December 31, 2011, compliance date remains appropriate for this low-
cost, but highly critical, safety requirement and no changes are 
proposed to the compliance dates for Sections 6D.03, 6E.02, and 7D.04.
    In Section 8B.04, as discussed above, a new requirement was adopted 
in the Final Rule for the 2009 edition of the MUTCD to require the use 
of either a Yield or Stop sign with the Crossbuck sign at all passive 
grade crossings, and a target compliance date of December 31, 2019, was 
established for adding these signs at existing crossings. This 10-year 
compliance date was established to promote increased safety at passive 
grade crossings, especially during nighttime hours. Although the new 
requirements involve conducting engineering studies for some locations 
and installing signs that do not currently exist at existing grade 
crossings, the existing 10-year target compliance date for installation 
of the required additional signs at existing locations remains 
appropriate.
Conclusion
    The proposed revisions to Table I-2 are intended to reduce the 
regulatory burden and provide increased flexibility to State and local 
highway agencies and to enable those agencies to make decisions on when 
to replace or upgrade existing noncompliant devices in accordance with 
their own local environmental conditions and the competing priorities 
in their communities for a wide variety of safety-related measures that 
might be needed in the context of limited budgets. The proposed 
revisions also simplify procedures for traffic control device 
replacements and reinforce the principle that most noncompliant traffic 
control devices can be replaced in the ordinary course of routine 
maintenance and/or when the useful life of such devices has expired. 
The few items for which target compliance dates are proposed to be 
retained or extended are, based on FHWA's experience and subject matter 
expertise on traffic control device issues, considered to be essential 
for statutory or safety reasons and/or of relatively low-cost to 
implement.
    It is important to understand that elimination of a compliance date 
for a given Standard contained in the MUTCD does not eliminate the

[[Page 54161]]

regulatory requirement to comply with that Standard. The Standard 
itself remains in the MUTCD and applies to any new installations, but 
the firm fixed date for replacing noncompliant devices that exist in 
the field is eliminated.
    On April 22, 2010, a separate NPA was published in the Federal 
Register \6\ proposing to revise the 2009 edition of the MUTCD 
regarding maintaining minimum retroreflectivity of longitudinal 
pavement markings. The deadline for comments to that docket has passed 
and the FHWA is currently reviewing the docket comments received. In 
that NPA, FHWA suggested that the proposed revisions regarding 
maintaining minimum retroreflectivity of longitudinal pavement markings 
would be designated as Revision 1 to the 2009 edition of the MUTCD. 
Actual designation of revision numbers will depend on the relative 
timing of any Final Rules that may be issued by the FHWA as a result of 
the April 22, 2010, NPA, this NPA, and any other NPAs regarding the 
MUTCD.
---------------------------------------------------------------------------

    \6\ 75 FR 20935, April 22, 2010.
---------------------------------------------------------------------------

Rulemaking Analysis and Notices

Executive Order 12866 (Regulatory Planning and Review), Executive Order 
13563 (Improving Regulation and Regulatory Review), and DOT Regulatory 
Policies and Procedures

    The FHWA has determined that this action would be a significant 
regulatory action within the meaning of Executive Order 12866 and 
within the meaning of DOT regulatory policies and procedures due to the 
significant public interest in issues surrounding the MUTCD. This 
action complies with Executive Orders 12866 and 13563 to improve 
regulation. In particular, this action is consistent with, and can be 
seen as directly responsive to, the requirements of Executive Order 
13563, and in particular its requirement for retrospective analysis of 
existing rules (section 6), with an emphasis on streamlining its 
regulations. This approach is also consistent with Presidential 
Memorandum, Administrative Flexibility, which calls for reducing 
burdens and promoting flexibility for State and local governments.
    The proposed changes in the MUTCD would reduce burdens on State and 
local government in the application of traffic control devices. They 
would provide additional clarification, guidance, and flexibility to 
such governments. The uniform application of traffic control devices 
will greatly improve roadway safety and traffic operations efficiency. 
The standards, guidance, options, and support are also used to create 
uniformity and to enhance safety and mobility. The proposed changes in 
this rulemaking will not require the expenditure of funds, but rather 
will provide State and local governments with the flexibility to 
allocate scarce financial resources based on local conditions and the 
useful service life of its traffic control devices. It is anticipated 
that the economic impact of this rulemaking would be minimal and indeed 
costs and burdens will be reduced, not increased; therefore, a full 
regulatory evaluation is not required.
    As noted, this action streamlines existing significant regulation 
to reduce burden and promote the flexibilities of State and local 
governments under Executive Order 13563. In response to concerns about 
the potential impact of previously adopted MUTCD compliance dates on 
State and local governments in the current economic climate, the FHWA 
published a Request for Comments on traffic control device compliance 
dates. The FHWA asked for responses to a series of seven questions 
about compliance dates, their benefits and potential economic impacts, 
especially economic hardships to State and local governments that might 
result from specific target compliance dates for upgrading certain non-
compliant existing devices. The responses received from that notice 
were considered in the development of this proposal. The FHWA 
anticipates that this proposed rulemaking will reduce the impacts of 
compliance dates on State and local highway agencies and will 
streamline and simplify information contained in the MUTCD.

Regulatory Flexibility Act

    In compliance with the Regulatory Flexibility Act (Pub. L. 96-354, 
5 U.S.C. 601-612), the FHWA has evaluated the effects of these changes 
on small entities and anticipates that this action would not have a 
significant economic impact on a substantial number of small entities. 
This proposed rule would reduce burdens and provide clarification and 
additional flexibility, and would not require an expenditure of funds.

Unfunded Mandates Reform Act of 1995

    This proposed rule would not impose unfunded mandates as defined by 
the Unfunded Mandates Reform Act of 1995 (Pub. L. 104-4, 109 Stat. 48, 
March 22, 1995). On the contrary, the proposed changes provide 
additional guidance, flexibility, and clarification and would not 
require an expenditure of funds. This action would not result in the 
expenditure by State, local, and tribal governments, in the aggregate, 
or by the private sector, of $140.8 million or more in any 1 year (2 
U.S.C. 1532). Further, in compliance with the Unfunded Mandates Reform 
Act of 1995, FHWA will evaluate any regulatory action that might be 
proposed in subsequent stages of the proceeding to assess the effects 
on State, local, and tribal governments and the private sector.

Executive Order 13132 (Federalism)

    This action has been analyzed in accordance with the principles and 
criteria contained in Executive Order 13132 dated August 4, 1999. This 
action would increase flexibility for State and local governments. The 
FHWA has determined that this action would not have sufficient 
federalism implications to warrant the preparation of a federalism 
assessment. The FHWA has also determined that this rulemaking will not 
preempt any State law or State regulation or affect the States' ability 
to discharge traditional State governmental functions. The MUTCD is 
incorporated by reference in 23 CFR part 655, subpart F. These proposed 
amendments are in keeping with the Secretary of Transportation's 
authority under 23 U.S.C. 109(d), 315, and 402(a) to promulgate uniform 
guidelines to promote the safe and efficient use of the highway. The 
overriding safety benefits of the uniformity prescribed by the MUTCD 
are shared by all of the State and local governments, and changes made 
to this rule are directed at enhancing safety. In general, the proposed 
amendments increase flexibility for States and local governments. To 
the extent that these proposed amendments override any existing State 
requirements regarding traffic control devices, they do so in the 
interest of national uniformity.

Executive Order 13175 (Tribal Consultation)

    The FHWA has analyzed this action under Executive Order 13175, 
dated November 6, 2000, and believes that it would not have substantial 
direct effects on one or more Indian tribes; would not impose 
substantial direct compliance costs on Indian tribal governments; and 
would not preempt tribal law. Therefore, a tribal summary impact 
statement is not required.

Executive Order 13211 (Energy Effects)

    The FHWA has analyzed this action under Executive Order 13211, 
Actions Concerning Regulations That Significantly Affect Energy Supply, 
Distribution, or Use. We have

[[Page 54162]]

determined that it is not a significant energy action under that order 
because it is not likely to have a significant adverse effect on the 
supply, distribution, or use of energy. Therefore, a Statement of 
Energy Effects under Executive Order 13211 is not required.

Executive Order 12372 (Intergovernmental Review)

    Catalog of Federal Domestic Assistance program Number 20.205, 
Highway Planning and Construction. The regulations implementing 
Executive Order 12372 regarding intergovernmental consultation on 
Federal programs and activities apply to this program.

Paperwork Reduction Act

    Under the Paperwork Reduction Act of 1995 (PRA) (44 U.S.C. 3501, et 
seq.), Federal agencies must obtain approval from the Office of 
Management and Budget for each collection of information they conduct, 
sponsor, or require through regulations. The FHWA has determined that 
this action does not contain collection information requirements for 
purposes of the PRA.

Executive Order 12988 (Civil Justice Reform)

    This action meets applicable standards in sections 3(a) and 3(b)(2) 
of Executive Order 12988, Civil Justice Reform, to minimize litigation, 
eliminate ambiguity, and reduce burden.

Executive Order 13045 (Protection of Children)

    The FHWA has analyzed this action under Executive Order 13045, 
Protection of Children from Environmental Health Risks and Safety 
Risks. The FHWA certifies that this action would not concern an 
environmental risk to health or safety that might disproportionately 
affect children.

Executive Order 12630 (Taking of Private Property)

    The FHWA does not anticipate that this action would affect a taking 
of private property or otherwise have taking implications under 
Executive Order 12630, Governmental Actions and Interference with 
Constitutionally Protected Property Rights.

National Environmental Policy Act

    The agency has analyzed this action for the purpose of the National 
Environmental Policy Act of 1969 (42 U.S.C. 4321-4347) and has 
determined that it would not have any effect on the quality of the 
environment.

Regulation Identification Number

    A regulation identification number (RIN) is assigned to each 
regulatory action listed in the Unified Agenda of Federal Regulations. 
The Regulatory Information Service Center publishes the Unified Agenda 
in April and October of each year. The RIN contained in the heading of 
this document can be used to cross reference this action with the 
Unified Agenda.

List of Subjects in 23 CFR Part 655

    Design standards, Grant programs--transportation, Highways and 
roads, Incorporation by reference, Signs, Traffic regulations.

    Issued on: August 23, 2011.
Victor M. Mendez,
Administrator.

    In consideration of the foregoing, the FHWA proposes to amend title 
23, Code of Federal Regulations part 655 as follows:

PART 655--TRAFFIC OPERATIONS

    1. The authority citation for part 655 continues to read as 
follows:

    Authority: 23 U.S.C. 101(a), 104, 109(d), 114(a), 217, 315, and 
402(a); 23 CFR 1.32; and, 49 CFR 1.48(b).

Subpart F--Traffic Control Devices on Federal-Aid and Other Streets 
and Highways--[Amended]

    2. Revise Sec.  655.601(a), to read as follows:


Sec.  655.601  Purpose.

* * * * *
    (a) Manual on Uniform Traffic Control Devices for Streets and 
Highways (MUTCD), 2009 Edition, with Revision(s) number ------ 
[revision number to be inserted] incorporated, FHWA, dated -------- 
[date to be inserted]. This publication is incorporated by reference in 
accordance with 5 U.S.C. 552(a) and 1 CFR part 51 and is on file at the 
National Archives and Records Administration (NARA). For information on 
the availability of this material at NARA call (202) 741-6030, or go to 
http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. It is available for inspection and 
copying at the Federal Highway Administration, 1200 New Jersey Avenue, 
SE., Washington, DC 20590, telephone 202-366-1993, as provided in 49 
CFR part 7. The text is also available from the FHWA Office of 
Operations Web site at: http//mutcd.fhwa.dot.gov.
* * * * *
[FR Doc. 2011-22006 Filed 8-30-11; 8:45 am]
BILLING CODE 4910-22-P