[Federal Register Volume 77, Number 62 (Friday, March 30, 2012)]
[Rules and Regulations]
[Pages 19063-19065]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-7002]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2012-0017; Directorate Identifier 2011-CE-039-AD;
Amendment 39-16994; AD 2012-06-13]
RIN 2120-AA64
Airworthiness Directives; DG Flugzeugbau GmbH Gliders
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for DG
Flugzeugbau GmbH Models DG-500 Elan Orion, DG-500 Elan Trainer, DG-500/
20 Elan, DG-500/22 Elan, DG-500M, and DG-500MB gliders. This AD results
from mandatory continuing airworthiness information (MCAI) issued by an
aviation authority of another country to identify and correct an unsafe
condition on an aviation product. The MCAI describes the unsafe
condition as damage to the bulkhead of the glider's center of gravity
(CG) tow hook that, if not detected and corrected, may lead to failure
of the fiberglass structure during a winch launch. We are issuing this
AD to require actions to address the unsafe condition on these
products.
DATES: This AD is effective May 4, 2012.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of May 4, 2012.
ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at Document Management Facility, U.S.
Department of Transportation, Docket Operations, M-30, West Building
Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC
20590.
For service information identified in this AD, contact DG-
Flugzeugbau GmbH, Otto-Lilienthal-Weg 2, 76646 Bruchsal, Federal
Republic of Germany; telephone: +49 (0) 7251 3020140, fax: +49 (0) 7251
3020149; email: [email protected]; Internet: www.dg-
flugzeugbau.de. You may review copies of the referenced service
information at the FAA, Small Airplane Directorate, 901 Locust St.,
Kansas City, Missouri 64106. For information on the availability of
this material at the FAA, call (816) 329-4148.
FOR FURTHER INFORMATION CONTACT: Jim Rutherford, Aerospace Engineer,
FAA, Small Airplane Directorate, 901 Locust St., Room 301, Kansas City,
Missouri 64106; telephone: (816) 329-4165; fax: (816) 329-4090; email:
[email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would apply to the specified products.
That NPRM was published in the Federal Register on January 17, 2012 (77
FR 2234). That NPRM proposed to correct an unsafe condition for the
specified products. The MCAI states:
Occurrence of damage of the bulkhead of CG tow hook and its
glued joints to fuselage shell was reported.
Investigation concluded that this damage may occur after wheel
up landing.
Damage of bulkheads for CG tow hook of the sailplane or powered
sailplane, if not detected and corrected, may lead to failure of
glass fibre structure during a winch launch.
DG-Flugzeugbau GmbH developed and published Technical Note (TN)
No 500/04 with the associated Working Instruction No. 1 to detect
and correct damaged CG tow hook bulkhead and its glued joints.
For the above-mentioned reasons, this AD requires a one-time
inspection of the CG tow hook and its reinforcement.
You may obtain further information by examining the MCAI in the AD
docket.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM (77 FR 2234, January 17,
2012) or on the determination of the cost to the public.
Conclusion
We reviewed the relevant data and determined that air safety and
the public interest require adopting the AD as proposed except for
minor editorial changes. We have determined that these minor changes:
Are consistent with the intent that was proposed in the
NPRM (77 FR 2234, January 17, 2012) for correcting the unsafe
condition; and
Do not add any additional burden upon the public than was
already proposed in the NPRM (77 FR 2234, January 17, 2012).
[[Page 19064]]
The MCAI requires you to inspect the CG tow hook bulkhead for damage
and reinforce the bulkhead.
Costs of Compliance
We estimate that this AD will affect 16 products of U.S. registry.
We also estimate that it will take about 5 work-hours per product to
comply with the basic requirements of this AD. The average labor rate
is $85 per work-hour. Required parts will cost about $1,030 per
product.
Based on these figures, we estimate the cost of the AD on U.S.
operators to be $23,280, or $1,455 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains the NPRM (77 FR 2234, January 17,
2012), the regulatory evaluation, any comments received, and other
information. The street address for the Docket Office (telephone (800)
647-5527) is in the ADDRESSES section. Comments will be available in
the AD docket shortly after receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
2012-06-13 DG Flugzeugbau GmbH: Amendment 39-16994; Docket No. FAA-
2012-0017; Directorate Identifier 2011-CE-039-AD.
(a) Effective Date
This airworthiness directive (AD) becomes effective May 4, 2012.
(b) Affected ADs
None.
(c) Applicability
This AD applies to DG Flugzeugbau GmbH Models DG-500 Elan Orion,
DG-500 Elan Trainer, DG-500/20 Elan, DG-500/22 Elan, DG-500M, and
DG-500MB gliders, all serial numbers (S/N), certificated in any
category.
(d) Subject
Air Transport Association of America (ATA) Code 53: Fuselage.
(e) Reason
This AD was prompted by damage to the bulkhead of the glider's
center of gravity (CG) tow hook that, if not detected and corrected,
may lead to failure of the fiberglass structure during a winch
launch. We are issuing this AD to require actions to address the
unsafe condition on these products.
(f) Actions and Compliance
Unless already done, do the following actions:
(1) For all gliders: Within 30 days after May 4, 2012 (the
effective date of this AD), inspect the bulkhead of the CG tow hook
and the bulkhead's glued joints for damage following DG Flugzeugbau
GmbH Technical Note No. 500/04, dated August 30, 2011; and DG
Flugzeugbau Working Instruction No. 1 for TN500/04, dated August 30,
2011.
(2) For all gliders: If you find damage during the inspection
required by paragraph (f)(1) of this AD, before further flight,
reinforce the bulkhead of the CG tow hook following DG Flugzeugbau
GmbH Technical Note No. 500/04, dated August 30, 2011; and DG
Flugzeugbau Working Instruction No. 1 for TN500/04, dated August 30,
2011.
(3) For all gliders: Unless already done as required by
paragraph (f)(2) of this AD, within 5 months after May 4, 2012 (the
effective date of this AD), reinforce the bulkhead of the CG tow
hook following DG Flugzeugbau GmbH Technical Note No. 500/04, dated
August 30, 2011; and DG Flugzeugbau Working Instruction No. 1 for
TN500/04, dated August 30, 2011.
(4) For gliders with S/N 5E1 through S/N 5E23: While doing the
modification required by paragraph (f)(2) or (f)(3) of this AD,
install a new adapted tow hook access cover following DG Flugzeugbau
GmbH Technical Note No. 500/04, dated August 30, 2011; and DG
Flugzeugbau Working Instruction No. 1 for TN500/04, dated August 30,
2011.
(5) For all gliders: Although the European Aviation Safety
Agency (EASA) MCAI and DG Flugzeugbau GmbH Technical Note No. 500/
04, dated August 30, 2011, allow the inspection required by
paragraph (f)(1) of this AD to be done by a pilot-owner, the U.S.
regulatory system requires all actions of this AD to be done by a
certified mechanic.
(g) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Standards Office, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Jim Rutherford, Aerospace Engineer, FAA, Small
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri
64106; telephone: (816) 329-4165; fax: (816) 329-4090; email:
[email protected]. Before using any approved AMOC on any
airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, a federal agency may not conduct or sponsor, and a person
is not required to respond to, nor shall a person be subject to a
penalty for failure to comply with a collection of information
subject to the requirements of
[[Page 19065]]
the Paperwork Reduction Act unless that collection of information
displays a current valid OMB Control Number. The OMB Control Number
for this information collection is 2120-0056. Public reporting for
this collection of information is estimated to be approximately 5
minutes per response, including the time for reviewing instructions,
completing and reviewing the collection of information. All
responses to this collection of information are mandatory. Comments
concerning the accuracy of this burden and suggestions for reducing
the burden should be directed to the FAA at: 800 Independence Ave.
SW., Washington, DC 20591, Attn: Information Collection Clearance
Officer, AES-200.
(h) Related Information
Refer to MCAI EASA AD No.: 2011-0209, dated October 26, 2011; DG
Flugzeugbau GmbH TN No 500/4, dated August 30, 2011; and DG
Flugzeugbau Working Instruction No. 1, dated August 30, 2011, for
related information.
(i) Material Incorporated by Reference
(1) You must use the following service information to do the
actions required by this AD, unless the AD specifies otherwise. The
Director of the Federal Register approved the incorporation by
reference (IBR) under 5 U.S.C. 552(a) and 1 CFR part 51 of the
following service information:
(i) DG Flugzeugbau GmbH Technical Note No. 500/04, dated August
30, 2011; and
(ii) DG Flugzeugbau Working Instruction No. 1 for TN500/04,
dated August 30, 2011.
(2) For service information identified in this AD, contact DG-
Flugzeugbau GmbH, Otto-Lilienthal-Weg 2, 76646 Bruchsal, Federal
Republic of Germany; telephone: +49 (0) 7251 3020140, fax: +49 (0)
7251 3020149; email: [email protected]; Internet: www.dg-
flugzeugbau.de.
(3) You may review copies of the service information at the FAA,
Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106.
For information on the availability of this material at the FAA,
call (816) 329-4148.
(4) You may also review copies of the service information that
is incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
Issued in Kansas City, Missouri, on March 19, 2012.
Earl Lawrence,
Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 2012-7002 Filed 3-29-12; 8:45 am]
BILLING CODE 4910-13-P