[Federal Register Volume 77, Number 124 (Wednesday, June 27, 2012)]
[Notices]
[Pages 38324-38336]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-15672]
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Mine Safety and Health Administration
Petitions for Modification of Application of Existing Mandatory
Safety Standards
AGENCY: Mine Safety and Health Administration, Labor.
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: Section 101(c) of the Federal Mine Safety and Health Act of
1977 and 30 CFR Part 44 govern the application, processing, and
disposition of petitions for modification. This notice is a summary of
petitions for modification submitted to the Mine Safety and Health
Administration (MSHA) by the parties listed below to modify the
application of existing mandatory safety standards codified in Title 30
of the Code of Federal Regulations.
DATES: All comments on the petitions must be received by the Office of
Standards, Regulations and Variances on or before July 27, 2012.
ADDRESSES: You may submit your comments, identified by ``docket
number'' on the subject line, by any of the following methods:
1. Electronic Mail: [email protected]. Include the docket
number of the petition in the subject line of the message.
2. Facsimile: 202-693-9441.
3. Regular Mail or Hand Delivery: MSHA, Office of Standards,
Regulations and Variances, 1100 Wilson Boulevard, Room 2350, Arlington,
Virginia 22209-3939, Attention: George F. Triebsch, Director, Office of
Standards, Regulations and Variances. Persons delivering documents are
required to check in at the receptionist's desk on the 21st floor.
Individuals may inspect copies of the petitions and comments during
normal business hours at the address listed above.
MSHA will consider only comments postmarked by the U.S. Postal
Service or proof of delivery from another delivery service such as UPS
or Federal Express on or before the deadline for comments.
FOR FURTHER INFORMATION CONTACT: Barbara Barron, Office of Standards,
Regulations and Variances at 202-693-9447 (Voice),
[email protected] (Email), or 202-693-9441 (Facsimile). [These are
not toll-free numbers.]
SUPPLEMENTARY INFORMATION:
I. Background
Section 101(c) of the Federal Mine Safety and Health Act of 1977
(Mine Act) allows the mine operator or representative of miners to file
a petition to modify the application of any mandatory safety standard
to a coal or other mine if the Secretary of Labor determines that:
(1) An alternative method of achieving the result of such standard
exists which will at all times guarantee no less than the same measure
of
[[Page 38325]]
protection afforded the miners of such mine by such standard; or
(2) That the application of such standard to such mine will result
in a diminution of safety to the miners in such mine.
In addition, the regulations at 30 CFR 44.10 and 44.11 establish
the requirements and procedures for filing petitions for modification.
II. Petitions for Modification
Docket Number: M-2012-096-C.
Petitioner: Mountain Coal Company, LLC, P.O. Box 591, 5174 Highway
133, Somerset, Colorado 81434.
Mine: West Elk Mine, MSHA I.D. No. 05-03672, located in Gunnison
County, Colorado.
Regulation Affected: 30 CFR 75.503 (Permissible electric face
equipment; maintenance) and 30 CFR 18.35(a)(5)(i) (Portable trailing
cables and cords).
Modification Request: The petitioner requests a modification of the
Decision and Order for an existing petition for modification, docket
number M-96-104-C issued on January 14, 1998. That petition was granted
for a three-phase 995-volt continuous mining machine and several other
pieces of equipment. The petitioner states that:
(1) Several stipulations in the Decision and Order address the use
of 2/0 trailing cable supplying power to the continuous miner.
(2) With the purchase of Joy 12CM27 continuous miners, the power
supply cable to these continuous miners is 4/0 rather than 2/0. Using
the minimum amount of current available and having the instantaneous
over-current protection set at 2,500 amps, the use of 1,100 feet of 4/0
trailing cable does not compromise miner safety nor does it adversely
impact electrical protection of the cable. Based on this information,
the petitioner requests a modification of the existing petition for
modification to allow the use of 1,100 feet of 4/0 trailing cable for
the continuous miners.
The petitioner asserts that with the terms and conditions of the
Decision and Order, the use of 1,100 feet of 4/0 cable for the
continuous miners will at all times guarantee no less than the same
measure of protection afforded by the existing standard.
Docket Number: M-2012-097-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene
County, Pennsylvania.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in or inby the last open
crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-098-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene
County, Pennsylvania.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance
meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of
[[Page 38326]]
the most practical and accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways will be examined by surveying personnel prior to use to
ensure the equipment is being maintained in a safe operating condition.
These examinations will include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-099-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Bailey Mine, MSHA I.D. No. 36-07230, located in Greene
County, Pennsylvania.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and
[[Page 38327]]
limitations associated with the use of nonpermissible surveying
equipment in areas where methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-100-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in
Washington County, Pennsylvania.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard: (a) Nonpermissible electronic surveying equipment will be
used when equivalent permissible electronic surveying equipment is not
available. Such nonpermissible surveying equipment includes portable
battery-operated total station surveying equipment, mine transits,
distance meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in or inby the last open
crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-101-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in
Washington County, Pennsylvania.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements). Modification Request: The petitioner
requests a modification of the existing standard to permit an
alternative method of compliance to permit the use of battery-powered
nonpermissible surveying equipment in return airways, including, but
not limited to, portable battery-operated mine transits, total station
surveying equipment, distance meters, and data loggers. The petitioner
states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways will be examined by surveying personnel prior to use to
ensure the equipment is being maintained in a safe operating condition.
These examinations will include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
[[Page 38328]]
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-102-C.
Petitioner: Consol Pennsylvania Coal Company, LLC, Three Gateway
Center, Suite 1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-
1000.
Mine: Enlow Fork Mine, MSHA I.D. No. 36-07416, located in
Washington County, Pennsylvania.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and limitations associated
with the use of nonpermissible surveying equipment in areas where
methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-103-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
[[Page 38329]]
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in or inby the last open
crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-104-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance
meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways will be examined by surveying personnel prior to use to
ensure the equipment is being maintained in a safe operating condition.
These examinations will include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper
[[Page 38330]]
operating condition as defined in 30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-105-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Alma No. 1 Deep Mine, MSHA I.D. No. 46-09277, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and limitations associated
with the use of nonpermissible surveying equipment in areas where
methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-106-C.
Petitioner: Consolidation Coal Company, Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in
Buchanan County, Virginia.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying
[[Page 38331]]
equipment, mine transits, distance meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in or inby the last open
crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-107-C.
Petitioner: Consolidation Coal Company, Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in
Buchanan County, Virginia.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance
meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways will be examined by surveying personnel prior to use to
ensure the equipment is being maintained in a safe operating condition.
These examinations will include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-108-C.
[[Page 38332]]
Petitioner: Consolidation Coal Company, Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Buchanan 1 Mine, MSHA I.D. No. 44-04856, located in
Buchanan County, Virginia.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and limitations associated
with the use of nonpermissible surveying equipment in areas where
methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-109-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: MT-41 (Bronzite II) Mine, MSHA I.D. No. 46-09307, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying
equipment, mine transits, distance meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before
[[Page 38333]]
and during the use of nonpermissible surveying equipment in or inby the
last open crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-110-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: MT-41 (Bronzite II) Mine, MSHA I.D. No. 46-09307, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance
meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways or inby the last open crosscut will be examined by
surveying personnel prior to use to ensure the equipment is being
maintained in a safe operating condition. These examinations will
include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-111-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: MT-41 (Bronzite II) Mine), MSHA I.D. No. 46-09307, located in
Mingo County, West Virginia.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact
[[Page 38334]]
location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and limitations associated
with the use of nonpermissible surveying equipment in areas where
methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-112-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Bronzite III Mine, MSHA I.D. No. 46-05978, located in Mingo
County, West Virginia.
Regulation Affected: 30 CFR 75.500(d) (Permissible electric
equipment).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
or inby the last open crosscut, including, but not limited to, portable
battery-operated mine transits, total station surveying equipment,
distance meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
or inby the last open crosscut will be examined by surveying personnel
prior to use to ensure the equipment is being maintained in a safe
operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in or inby the last open
crosscut.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn outby the last open crosscut.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air outby the last open crosscut.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in
[[Page 38335]]
compliance with all the terms and conditions in this petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-113-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Bronzite III, MSHA I.D. No. 46-05978, located in Mingo
County, West Virginia.
Regulation Affected: 30 CFR 75.507-1(a) (Electric equipment other
than power-connection points; outby the last open crosscut; return air;
permissibility requirements).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment in
return airways, including, but not limited to, portable battery-
operated mine transits, total station surveying equipment, distance
meters, and data loggers. The petitioner states that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used in
return airways will be examined by surveying personnel prior to use to
ensure the equipment is being maintained in a safe operating condition.
These examinations will include the following steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment in return airways.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn out of the return airways.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air out of the return.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards associated with the use of
nonpermissible surveying equipment in areas where methane could be
present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Docket Number: M-2012-114-C.
Petitioner: Consol of Kentucky, Inc., Three Gateway Center, Suite
1340, 401 Liberty Avenue, Pittsburgh, Pennsylvania 15222-1000.
Mine: Bronzite III Mine, MSHA I.D. No. 46-05978, located in Mingo
County, West Virginia.
Regulation Affected: 30 CFR 75.1002(a) (Installation of electric
equipment and conductors; permissibility).
Modification Request: The petitioner requests a modification of the
existing standard to permit an alternative method of compliance to
permit the use of battery-powered nonpermissible surveying equipment
within 150 feet of pillar workings, including, but not limited to,
portable battery-operated mine transits, total station surveying
equipment, distance meters, and data loggers. The petitioner states
that:
(1) To comply with requirements for mine ventilation maps and mine
maps in 30 CFR 75.372 and 75.1200, use of the most practical and
accurate surveying equipment is necessary. To ensure the safety of the
miners in active mines and to protect miners in future mines that may
mine in close proximity to these same active mines, it is necessary to
determine the exact location and extent of the mine workings.
(2) Application of the existing standard would result in a
diminution of safety to the miners. Underground mining by its nature
and size, and the complexity of mine plans, requires that accurate and
precise measurements be completed in a prompt and efficient manner. The
petitioner proposes the following as an alternative to the existing
standard:
(a) Nonpermissible electronic surveying equipment will be used when
equivalent permissible electronic surveying equipment is not available.
Such nonpermissible surveying equipment includes portable battery-
operated total station surveying equipment, mine transits, distance
meters, and data loggers.
(b) All nonpermissible electronic surveying equipment to be used
within 150 feet of pillar workings will be examined by surveying
personnel prior to use to ensure the equipment is being maintained in a
safe operating condition. These examinations will include the following
steps:
(i) Checking the instrument for any physical damage and the
integrity of the case.
(ii) Removing the battery and inspecting for corrosion.
[[Page 38336]]
(iii) Inspecting the contact points to ensure a secure connection
to the battery.
(iv) Reinserting the battery and powering up and shutting down to
ensure proper connections.
(v) Checking the battery compartment cover to ensure that it is
securely fastened.
(c) The results of such examinations will be recorded and retained
for one year and made available to MSHA on request.
(d) A qualified person as defined in 30 CFR 75.151 will
continuously monitor for methane immediately before and during the use
of nonpermissible surveying equipment within 150 feet of pillar
workings.
(e) Nonpermissible surveying equipment will not be used if methane
is detected in concentrations at or above one percent for the area
being surveyed. When methane is detected at such levels while the
nonpermissible surveying equipment is being used, the equipment will be
deenergized immediately and the nonpermissible electronic equipment
withdrawn further than 150 feet from pillar workings.
(f) All hand-held methane detectors will be MSHA-approved and
maintained in permissible and proper operating condition as defined in
30 CFR 75.320.
(g) Batteries in the surveying equipment must be changed out or
charged in fresh air more than 150 feet from pillar workings.
(h) Qualified personnel who use surveying equipment will be
properly trained to recognize the hazards and limitations associated
with the use of nonpermissible surveying equipment in areas where
methane could be present.
(i) The nonpermissible surveying equipment will not be put into
service until MSHA has initially inspected the equipment and determined
that it is in compliance with all the terms and conditions in this
petition.
Within 60 days after the Proposed Decision and Order becomes final,
the petitioner will submit proposed revisions for its approved 30 CFR
part 48 training plan to the District Manager. The revisions will
specify initial and refresher training regarding the terms and
conditions in the Proposed Decision and Order.
The petitioner asserts that the proposed alternative method will at
all times guarantee no less than the same measure of protection as that
afforded by the existing standard.
Dated: June 22, 2012.
George F. Triebsch,
Director, Office of Standards, Regulations and Variances.
[FR Doc. 2012-15672 Filed 6-26-12; 8:45 am]
BILLING CODE 4510-43-P