[Federal Register Volume 77, Number 141 (Monday, July 23, 2012)]
[Rules and Regulations]
[Pages 42988-42989]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-17872]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Occupational Safety and Health Administration
29 CFR Part 1926
[Docket No. OSHA-2011-0184]
RIN 1218-AC65
Updating OSHA Construction Standards Based on National Consensus
Standards; Head Protection; Correction of Direct Final Rule
AGENCY: Occupational Safety and Health Administration (OSHA),
Department of Labor.
ACTION: Direct final rule; correction.
-----------------------------------------------------------------------
SUMMARY: OSHA is correcting a direct final rule (DFR) with regard to
the construction industry head protection standards to eliminate
confusion resulting from a drafting error. OSHA published the DFR on
June 22, 2012 (77 FR 37587). OSHA also is publishing a correction to
the proposed rule that it published the same day in the Federal
Register (77 FR 37617).
DATES: This correction to the direct final rule will become effective
on September 20, 2012.
FOR FURTHER INFORMATION CONTACT:
General information and press inquiries: Contact Frank Meilinger,
OSHA Office of Communications, Room N-3647, U.S. Department of Labor,
200 Constitution Ave. NW., Washington, DC 20210; telephone: (202) 693-
1999; email: [email protected].
Technical inquiries: Contact Kenneth Stevanus, Directorate of
Standards and Guidance, Room N-3609, OSHA, U.S. Department of Labor,
200 Constitution Ave. NW., Washington, DC 20210; telephone: (202) 693-
2260; fax: (202) 693-1663; email: [email protected].
SUPPLEMENTARY INFORMATION: OSHA is making the following correction in
FR document number 2012-15030, appearing on page 37600 in the Federal
Register of Friday, June 22, 2012:
Sec. 1926.100 [Corrected]
On page 37600, correct instruction number 16, to read as follows:
0
16. Amend Sec. 1926.100 as follows:
0
a. Remove paragraph (c).
0
b. Revise paragraph (b) to read as follows:
1926.100 Head protection.
* * * * *
(b) Criteria for head protection. (1) The employer must provide
each employee with head protection that meets the specifications
contained in any of the following consensus standards:
(i) American National Standards Institute (ANSI) Z89.1-2009,
``American National Standard for Industrial Head Protection,''
incorporated by reference in Sec. 1926.6;
(ii) American National Standards Institute (ANSI) Z89.1-2003,
``American National Standard for Industrial Head
[[Page 42989]]
Protection,'' incorporated by reference in Sec. 1926.6; or
(iii) American National Standards Institute (ANSI) Z89.1-1997,
``American National Standard for Personnel Protection--Protective
Headwear for Industrial Workers--Requirements,'' incorporated by
reference in Sec. 1926.6.
(2) The employer must ensure that the head protection provided for
each employee exposed to high-voltage electric shock and burns also
meets the specifications contained in Section 9.7 (``Electrical
Insulation'') of any of the consensus standards identified in paragraph
(b)(1) of this section.
(3) OSHA will deem any head protection device that the employer
demonstrates is at least as effective as a head protection device
constructed in accordance with one of the consensus standards
identified in paragraph (b)(1) of this section to be in compliance with
the requirements of this section.
Signed at Washington, DC, on July 17, 2012.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2012-17872 Filed 7-20-12; 8:45 am]
BILLING CODE P