[Federal Register Volume 77, Number 232 (Monday, December 3, 2012)]
[Rules and Regulations]
[Pages 71491-71492]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2012-28637]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0681; Directorate Identifier 2008-NE-13-AD;
Amendment 39-17268; AD 2012-23-12]
RIN 2120-AA64
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding an existing airworthiness directive (AD)
for all Turbomeca S.A. Arriel 1E2, 1S, and 1S1 turboshaft engines. That
AD currently requires a one-time inspection and torque check of the 3-
way union plug installed on all fuel control units (FCUs). This new AD
requires the same actions. This AD also requires reduction of the
applicability to certain FCUs and references an updated service
bulletin containing additional detailed information to identify the
non-compliant ``red disk.'' This AD also requires replacement of the
plug before further flight if it is found to be non-compliant, and
prohibits installation of FCUs that have not passed the 3-way union
plug inspection and torque check. This AD was prompted by Turbomeca
S.A. informing us that FCUs manufactured, repaired, or overhauled after
March 31, 2008, do not require inspection. We are issuing this AD to
prevent fuel leaks, which could result in a fire and damage to the
helicopter.
DATES: This AD is effective January 7, 2013.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in the AD as of January 7,
2013.
ADDRESSES: For service information identified in this AD, contact
Turbomeca S.A., 40220 Tarnos, France; phone: 33 (0)5 59 74 40 00;
telex: 570 042; fax: 33 (0)5 59 74 45 15. You may view this service
information at the FAA, Engine & Propeller Directorate, 12 New England
Executive Park, Burlington, MA. For information on the availability of
this material at the FAA, call 781-238-7125.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (phone: 800-647-5527) is Document Management Facility,
U.S. Department of Transportation, Docket Operations, M-30, West
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Rose Len, Aerospace Engineer, Engine &
Propeller Directorate, FAA, 12 New England Executive Park, Burlington,
MA 01803; phone: 781-238-7772; fax: 781-238-7199; email:
[email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to supersede AD 2009-03-04, Amendment 39-15805 (74 FR 7796,
February 20, 2009). That AD applies to the specified products. The NPRM
published in the Federal Register on July 25, 2012 (77 FR 43552). That
NPRM proposed to require a one-time inspection and torque check of the
3-way union plug, replacement of the plug before further flight if it
is found to be non-compliant, and would prohibit installation of FCUs
that have not passed the 3-way union plug inspection and torque check.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM.
Conclusion
We reviewed the relevant data and determined that air safety and
the public interest require adopting the AD as proposed.
Costs of Compliance
Based on the updated service information, we estimate that this AD
will affect about 179 engines installed on helicopters of U.S.
registry. We also estimate that it will take about 0.5 hour per product
to comply with this AD. The average labor rate is $85 per hour.
Required parts will cost about $14 per product. Based on these figures,
we estimate the cost of the AD on U.S. operators to be $10,114. Our
cost estimate is exclusive of possible warranty coverage.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more
[[Page 71492]]
detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing airworthiness directive (AD)
2009-03-04, Amendment 39-15805 (74 FR 7796, February 20, 2009), and
adding the following new AD:
2012-23-12 Turbomeca S.A.: Amendment 39-17268; Docket No. FAA-2008-
0681; Directorate Identifier 2008-NE-13-AD.
(a) Effective Date
This airworthiness directive (AD) is effective January 7, 2013.
(b) Affected ADs
This AD supersedes AD 2009-03-04, Amendment 39-15805 (74 FR
7796, February 20, 2009.
(c) Applicability
This AD applies to Turbomeca S.A. models Arriel 1E2, 1S, and 1S1
turboshaft engines with FCUs manufactured, repaired, or overhauled
on or before March 31, 2008.
(d) Unsafe Condition
Turbomeca S.A. informed the European Aviation Safety Agency of a
case of a ``red disk'' plug, adapted for bench testing, which was
installed on the FCU on an engine and released for service
operation. An engine experienced an in-service high pressure leak
event (at the fuel pump outlet) due to cracking of this ``red disk''
plug. This leak could lead to in-flight flame-out and/or possibly a
fire. This AD was prompted by Turbomeca S.A. informing us that FCUs
manufactured, repaired, or overhauled after March 31, 2008, do not
require inspection. We are issuing this AD to prevent fuel leaks,
which could result in a fire and damage to the helicopter.
(e) Compliance
Comply with this AD within the compliance times specified,
unless already done. Within 100 operating hours from the effective
date of this AD, perform a one-time inspection of the plug installed
in the FCU 3-way union, part number 9 932 30 706 0.
(1) If the FCU 3-way union plug is unpainted, verify the plug is
torqued to between 1.3 and 1.5 daN.m, in accordance with Turbomeca
S.A. Mandatory Service Bulletin (MSB) No. 292 73 0817, Version D,
dated February 29, 2012, before further flight.
(2) If the FCU 3-way union plug has any red paint on it, replace
it with a serviceable plug and torque the plug to between 1.3 and
1.5 daN.m, in accordance with Turbomeca S.A. MSB No. 292 73 0817,
Version D, dated February 29, 2012, before further flight.
(f) Installation Prohibition
After the effective date of this AD, do not install any FCU
manufactured, repaired, or overhauled on or before March 31, 2008,
onto any Turbomeca S.A. model Arriel 1E2, 1S, and 1S1 turboshaft
engine, unless the FCU 3-way union plug has passed the one-time
inspection and torque check required by this AD.
(g) Credit for Previous Actions
If you performed the inspections and corrective actions required
by this AD using the original issue or any version up to and
including Version D of Turbomeca S.A. MSB No. 292 73 0817 before the
effective date of this AD, you have met the requirements of this AD.
(h) Alternative Methods of Compliance (AMOCs)
The Manager, Engine Certification Office, may approve AMOCs for
this AD. Use the procedures found in 14 CFR 39.19 to make your
request.
(i) Related Information
(1) For more information about this AD, contact Rose Len,
Aerospace Engineer, Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington, MA
01803; phone: 781-238-7772; fax: 781-238-7199; email:
[email protected].
(2) Refer to European Aviation Safety Agency Airworthiness
Directive 2012-0063, dated April 17, 2012, for related information.
(j) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(i) Turbomeca S.A. Mandatory Service Bulletin No. 292 73 0817,
Version D, dated February 29, 2012.
(ii) Reserved.
(3) For service information identified in this AD, contact
Turbomeca S.A., 40220 Tarnos, France; phone: 33 (0)5 59 74 40 00;
telex: 570 042; fax: 33 (0)5 59 74 45 15.
(4) You may view this service information at the FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington,
MA. For information on the availability of this material at the FAA,
call 781-238-7125.
(5) You may view this service information at the National
Archives and Records Administration (NARA). For information on the
availability of this material at NARA, call 202-741-6030, or go to:
http://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Burlington, Massachusetts, on November 14, 2012.
Colleen M. D'Alessandro,
Assistant Manager, Engine & Propeller Directorate, Aircraft
Certification Service.
[FR Doc. 2012-28637 Filed 11-30-12; 8:45 am]
BILLING CODE 4910-13-P