[Federal Register Volume 78, Number 92 (Monday, May 13, 2013)]
[Notices]
[Pages 27951-27953]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-11196]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

Foreign-Trade Zones Board

[B-41-2013]


Foreign-Trade Zone (FTZ) 75--Phoenix, Arizona; Notification of 
Proposed Production Activity; Honeywell Aerospace, Inc., (Aircraft 
Engines, Systems and Components), Phoenix and Tempe, Arizona

    The City of Phoenix, grantee of FTZ 75, submitted a notification of 
proposed production activity to the FTZ Board on behalf of Honeywell 
Aerospace, Inc (Honeywell), located in Phoenix and Tempe, Arizona. The 
notification conforming to the requirements of the regulations of the 
FTZ Board (15 CFR 400.22) was received on May 3, 2013.
    The Honeywell facilities are located within Subzone 75J. The 
facilities are used for the production of aircraft engines, systems and 
components. Pursuant to 15 CFR 400.14(b), FTZ activity would be limited 
to the specific foreign-status materials and components and specific 
finished products described in the submitted notification (as described 
below) and subsequently authorized by the FTZ Board.
    Production under FTZ procedures could exempt Honeywell from customs 
duty payments on the foreign status components used in export 
production. On its domestic sales, Honeywell would be able to choose 
the duty rates during customs entry procedures that apply to: Turbofan 
engines; turbo-propeller engines; turbo-shaft engines; auxiliary power 
units; rotor assemblies; tube assemblies; hydraulic actuators; air-
turbine starters; wheel turbines; air-turbine pump systems; duct 
temperature limiters; air/oil heat exchangers; oil cooler fans; fuel 
filter assemblies; shutoffs and regulators valves; dual 3-way valves; 
check valves; pneumatic overpressure outline valves; regulating and 
shutoff pressure valves; center-drive units; shaft assemblies; bearing 
housings; gearbox assemblies; shaft couplings; spur gears; tertiary 
outline locks; power supplies; outline brake modules; data 
transmitters; XM receivers; XM antennas; head-up displays and 
components; electrical control panels; EPROMS; microcircuits; air-data 
transducers; axles with wheel and brake assemblies; aeronautical 
instruments; duct temperature sensors; flow-sensing modules; air/
outflow-sensing modules; air-data modules; thermo switches; and, 
temperature control valves (duty rate free--3.30%) for the foreign 
status inputs noted below. Customs duties also could

[[Page 27952]]

possibly be deferred or reduced on foreign status production equipment.
    The components and materials sourced from abroad include: Unwrought 
titanium alloy; Kevlar-woven fabric; sample oil; scandium oxide; 
silicon nitride; turbine oil; varnish; X-ray films; guide springs; 
plastic tubes; plastic hose assemblies; plastic markers; plastic hose 
ducts; decals; tape; foam strips; ignition-exciter spacers and 
insulators; shielding bags; plastic caps; plastic thrust washers; 
rubber inserts; rubber tooth belts; pre-formed rubber gaskets; rubber 
tips; pine shipping guards; wood boards; corrugated packing boxes; 
logbooks; technical manuals; spinner decals; air diaphragms; duct 
gaskets; grinding wheels and tooling; asbestos gaskets; carbon washers; 
carbon seals; thermal carbon-fiber insulation blankets; ceramic turbine 
blisks; sight glasses; glass tubes; insulation and fire-protection 
shields; fiberglass covers and blankets; iron or steel angles; exhaust 
ducks; pneumatic tubes; metal tube actuators; double-ended union tubes; 
adaptor valve assemblies; flared union tubes; union assemblies; 
spherical-end adaptors; engine oil tanks; cable lifts; cable 
assemblies; chain assemblies; screws; double-hex bolts; threaded 
covers; turnbuckles; springs; thrust washers; rivets; retaining 
springs; tube sleeves; leaf springs; drain springs; torsion rods; 
forgings; wire clips; tube nipple assemblies; balancing wire; jumper-
cable assemblies; seals; floating nuts; stiffener bars; nickel alloy 
bars; tubes and pipe fittings; straight-headed pins; test blocks; 
protective shipping devices; high voltage covers; gear plates; plates; 
XFR tubes; tubes; flow restrictor plugs; inserts; rig-pin brackets; 
grooved, headless pins; adaptor assemblies; filter extractors; de-
coupler/disassembly wrenches; torque wrench adaptors; test benches; 
drills; screwdrivers; retract nut fixtures; clamp and baffle flappers; 
riveting anvils; alignment kits; crimp fixtures; assembly drill 
fixtures; carbide reamers; taper cutters; small wire brushes; bits; 
grooved pins; position stops; servo brackets; nameplates; turbojets; 
turbo-propellers; gas-turbine engines; stop mechanisms; internal gear 
hubs; linear hydraulic actuators; piston-spacer rings; electro-
pneumatic outline actuators; engine air starters; actuator motor 
valves; piston-ring sets; pump assemblies; air-turbine pump systems; 
lubrication pump assemblies; turbine engine pumps; lube pump shafts; 
turbine stators; vacuum test equipment; fan assemblies; air 
compressors; cabinet fans; cooling packs; duct temperature limiters; 
environmental control units; split ducts; oil temperature regulators; 
outlet coolers; fuel heaters; oil cooler fans; filter assemblies; oil 
filter install kits; cartridge screens; filter housings; trim balance 
weights; fire bottles; water-spray nozzles; lift fixtures; inlet 
lifting slings; flight deck printers; laser drilling systems; grinding 
fixture set; machining tools; hydraulic presses; test equipment 
fixtures; turbine seal driver fixtures; hydraulic press/housing removal 
fixtures; bearing install tools; laptops; computer servers; computer 
systems; touch screens; disk drives; electronic flight-bag interface 
units; programmers; computer parts; dual-layer spinnerets; wet vacuum 
impregnation machines; translating nuts; piston housing assemblies; 
investment dies; cast die tooling; regulator valves; outline pressure 
regulator valves; outline check valves; safety valves; temperature 
control valves; switch interrupter assemblies; annular ball bearings; 
roller bearings; plain bearings, radial needle-roller bearings; sun-
gear bearings; ball kits; bushings; butterfly shafts; planetary-gear 
bearings; turbine carriers; screw and nut ball bearings; ratchet shaft 
splines; spur-gear assemblies; shaft seals; nozzle gaskets; encased 
seals; actuator assembly motors; servo-drive assemblies; actuators; 
starter motors; rotary actuators; geared AC-motors; AC generators; 
brake assembly arms; power units, DV modulators; power supplies; 
transducers; interface cards; magnets; brake modules; solenoid 
assemblies; lithium batteries; ignition exciters; electric starters; 
igniters; aluminum castings; plasma arc welding machines and fixtures; 
electric furnace components ; heater plates; computer displays; 
encryption boxes; power supply assemblies; remote microphones; 
loudspeakers; amplifiers; cockpit voice recorders; diskettes; software 
CDs; memory cards; aircraft identification modules; video tapes; 
international receiver and decoder module assemblies; weather radar 
receivers and transmitters; radio altimeter receivers and transmitters; 
LCD monitors; VLF antennas; nuclear instrumentation modules; emergency 
locator transmitters with alarm; multi-function displays; CRT display 
units; circuit card assemblies; ceramic capacitors; capacitors; 
aluminum electrolytic capacitors; ceramic, surface-mounted capacitors; 
mica capacitors; resistors; fixed-film resistors; linear variable-
resistor assemblies; variable-resistor assemblies; resistor assemblies; 
angular potentiometers; temperature sensors/resistors; printed circuit 
boards; switch assembly actuators; contacts; radio frequency filters; 
relays; switch assemblies; switches; light-board switches; electrical-
connector receptacles; housings; control boxes; printed wiring boards; 
adapter switches; lamps; CRT assemblies; tube and bezel assemblies; 
magnetron tubes; diodes; microwave power transistors; transistors; 
semiconductor devices; light-emitting diodes; surface-mount 
semiconductors; oscillators; microcircuits; masks; IC switches; 
integrated-circuit heat sinks; signal generator test equipment; linear, 
dual transformers; printed board assemblies; coaxial cable; electrical 
wiring harnesses; strain-gage cable; test adaptors; fiber-optic 
couplers; electrodes; insulators; insulator sleeves; ceramic filters; 
transport carts; aircraft; brake rotor piston housings; pneumatic 
actuators; spacer retainers; computer interface cards; LCD glass; glass 
LCD covers; mach trim couplers; integrated computers; nozzle castings; 
ultrasound instruments; concave gauges; shim-checking gauges; gauge 
dials; test vehicles and machinery; chemise thermo-couplers; duct 
temperature sensors; calibration thermostats; liquid level gauges; air-
flow sensor outlets; flow meters; air quality monitors; photometers; 
densitometers; reflectance standards; start counter meters; hand-held 
tachometers; oscilloscopes; multi-meters; light-wave multi-meters; 
bleed valves; signal generators and decoders; digital multi-meters; 
waveform analyzers; electrical test equipment holding fixtures; balance 
arbors; simulator test fixtures; optical protractors; borescope tube 
assemblies; piezoelectric accelerometers; bearing housings; body 
thermostats; controllers; generator control units; relief valves; time 
meters; metal engine stands; incandescent lamps; and, igniter leads 
(duty rate ranges from 0 to 15%).
    Public comment is invited from interested parties. Submissions 
shall be addressed to the Board's Executive Secretary at the address 
below. The closing period for their receipt is June 24, 2013.
    A copy of the notification will be available for public inspection 
at the Office of the Executive Secretary, Foreign-Trade Zones Board, 
Room 21013, U.S. Department of Commerce, 1401 Constitution Avenue NW., 
Washington, DC 20230-0002, and in the ``Reading Room'' section of the 
Board's Web site, which is accessible via www.trade.gov/ftz.

FOR FURTHER INFORMATION CONTACT: Christopher Kemp at 
[email protected] or (202) 482-0862.


[[Page 27953]]


    Dated: May 6, 2013.
Andrew McGilvray,
Executive Secretary.
[FR Doc. 2013-11196 Filed 5-10-13; 8:45 am]
BILLING CODE 3510-DS-P