[Federal Register Volume 78, Number 138 (Thursday, July 18, 2013)]
[Notices]
[Pages 42929-42930]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-17261]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF COMMERCE
Foreign-Trade Zones Board
[B-73-2013]
Foreign-Trade Zone (FTZ) 41--Milwaukee, Wisconsin, Notification
of Proposed Production Activity, Broan-NuTone LLC (Home Ventilation
Products and Heaters), Hartford, Wisconsin
Broan-NuTone, LLC (Broan-NuTone) submitted a notification of
proposed production activity to the FTZ Board for its facility in
Hartford, Wisconsin within Subzone 41L. The notification conforming to
the requirements of the regulations of the FTZ Board (15 CFR 400.22)
was received on June 26, 2013.
The Broan-NuTone facility is used for the manufacturing and
distribution of residential range hoods, subassemblies or component
parts for centrifugal blowers, ceiling exhaust fans, wall or ceiling
heaters, blower assemblies and roof and wall caps. Pursuant to 15 CFR
400.14(b), FTZ activity would be limited to the specific foreign-status
materials and components and specific finished products described in
the submitted notification (as described below) and subsequently
authorized by the FTZ Board.
Production under FTZ procedures could exempt Broan-NuTone from
customs duty payments on the foreign status components used in export
production. On its domestic sales, Broan-NuTone would be able to choose
the duty rates during customs entry procedures that apply to range
hoods/down drafts, blower assemblies, ceiling exhaust fans for
permanent installation, roof/wall caps and heaters (floor, wall or
ceiling) (duty rate ranges from free to 4.7%) for the foreign status
inputs noted below. Customs duties also could possibly be deferred or
reduced on foreign status production equipment.
[[Page 42930]]
The components and materials sourced from abroad include: polymer
paint, label materials, logo materials, packaging materials, plastic
packing, plastic bags, plastic trim pieces and switch covers, rubber
spacers, plastic items, rubber gaskets, gaskets, rubber washers, rubber
stoppers, rubber grommets, other rubber articles, cartons, bags,
corrugated boxes with fillers, instruction sheets, range hood filters,
bathroom mirrors, filters for whole house ventilation systems, cold-
rolled steel for manufacturing, flat-rolled steel for manufacturing,
plated wire, housing for recessed range hood, wire mesh for bird
screens, roof/wall caps, screws, fasteners, stainless steel screws,
nuts, washers, rivet housing assembly, damper or filter springs for
grille, stainless steel kitchen backsplashes, brackets, aluminum
stainless for manufacturing, zinc screws, parts of hinges, hinge
cabinets, mounting brackets, brackets, metal flex ducts, ceiling
exhaust or paddle fans, wall or ceiling exhaust fans, residential range
hood canopies, parts used in ventilation, filters, parts of filters,
central valve dampers, roller down drafts, electric motors for exhaust/
ventilation, electric motors for downdraft range hoods, parts used on
electric motors, light ballasts, transformers, magnets for range hoods,
portable heaters and fans, heating resistors, parts for heaters,
capacitors, ceramic capacitors, resistors, fuses, circuit breakers for
exhaust/heater units, relays, motor starters, wall switches, various
switch types, lamp sockets, other electrical parts, switch parts, male/
female connectors, terminals for switches, other apparatus for
switches, printed circuit boards, membrane covers for switches, halogen
light bulbs, light bulbs, fluorescent light bulbs, light housing for
range hoods, light diodes, coaxial cables, wire harnesses, cable wires,
fuse holders, snap bushing (damper), air pressure switch valves,
thermostat/heat sensor for ventilation, heat regulator/dehumidistat,
timer switch assembly, timer control switch assembly, metal housing
medicine cabinets, wood trimmed medicine cabinets, plastic housing
medicine cabinets, wood components for medicine cabinets, metal
components for cabinets, light kits for fans with base metal, non-base
metal light fittings, base metal parts for light kits, parts for light
kits, glass globes and other parts of lamps (finials) (duty rate ranges
from free to 12%).
Public comment is invited from interested parties. Submissions
shall be addressed to the Board's Executive Secretary at the address
below. The closing period for their receipt is August 27, 2013.
A copy of the notification will be available for public inspection
at the Office of the Executive Secretary, Foreign-Trade Zones Board,
Room 21013, U.S. Department of Commerce, 1401 Constitution Avenue NW.,
Washington, DC 20230-0002, and in the ``Reading Room'' section of the
Board's Web site, which is accessible via www.trade.gov/ftz.
FOR FURTHER INFORMATION CONTACT: Elizabeth Whiteman at
[email protected] or (202) 482-0473.
Dated: July 11, 2013.
Andrew McGilvray,
Executive Secretary.
[FR Doc. 2013-17261 Filed 7-17-13; 8:45 am]
BILLING CODE 3510-DS-P