[Federal Register Volume 78, Number 161 (Tuesday, August 20, 2013)]
[Proposed Rules]
[Pages 51123-51126]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-20309]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0734; Directorate Identifier 2012-SW-080-AD]
RIN 2120-AA64
Airworthiness Directives; Bell Helicopter Textron
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to supersede an existing airworthiness directive
(AD) for Bell Helicopter Textron (Bell) Model 222, 222B, 222U, 230, and
430 helicopters. The existing AD currently requires inspecting parts of
the main rotor hydraulic servo actuator (servo actuator) for certain
conditions and
[[Page 51124]]
replacing any unairworthy parts before further flight. Since we issued
the AD, a new stainless steel piston rod has been manufactured. We
propose requiring the installation of a servo actuator assembly with
this piston rod and setting an interval for the next overhaul at 10,000
hours time-in-service (TIS) or 10 years, whichever comes first. The
proposed actions are intended to detect pitting or penetration of the
base metal of the piston rod that could lead to the piston rod's
failure, the servo actuator's failure, and the loss of helicopter
control.
DATES: We must receive comments on this proposed AD by October 21,
2013.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Docket: Go to http://www.regulations.gov. Follow the online instructions for sending your
comments electronically.
Fax: 202-493-2251.
Mail: Send comments to the U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590-0001.
Hand Delivery: Deliver to the ``Mail'' address between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the Docket Operations Office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the foreign
authority's AD, the economic evaluation, any comments received and
other information. The street address for the Docket Operations Office
(telephone 800-647-5527) is in the ADDRESSES section. Comments will be
available in the AD docket shortly after receipt.
For service information identified in this proposed AD, contact
Bell Helicopter Textron, 12,800 Rue de l'Avenir, Mirabel, Quebec
J7J1R4; telephone (450) 437-2862 or (800) 363-8023; fax (450) 433-0272;
or at http://www.bellcustomer.com/files/. You may review service
information at the FAA, Office of the Regional Counsel, Southwest
Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137.
FOR FURTHER INFORMATION CONTACT: Matt Wilbanks, Aviation Safety
Engineer, Rotorcraft Certification Office, Rotorcraft Directorate, FAA,
2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817) 222-5110;
email [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to participate in this rulemaking by submitting
written comments, data, or views. We also invite comments relating to
the economic, environmental, energy, or federalism impacts that might
result from adopting the proposals in this document. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. To
ensure the docket does not contain duplicate comments, commenters
should send only one copy of written comments, or if comments are filed
electronically, commenters should submit only one time.
We will file in the docket all comments that we receive, as well as
a report summarizing each substantive public contact with FAA personnel
concerning this proposed rulemaking. Before acting on this proposal, we
will consider all comments we receive on or before the closing date for
comments. We will consider comments filed after the comment period has
closed if it is possible to do so without incurring expense or delay.
We may change this proposal in light of the comments we receive.
Discussion
On November 24, 2010, we published AD 2010-19-51, Amendment 39-
16523 (75 FR 71540), for Bell Model 222, 222B, 222U, 230, and 430
helicopters. AD 2010-19-51 requires inspecting parts of the servo
actuator for certain conditions and replacing any unairworthy parts
before further flight. AD 2010-19-51 was prompted by a collective servo
actuator malfunction. A subsequent investigation revealed that the
output piston rod assembly had fractured at the threaded end because of
corrosion cracking. The investigation also showed a nonconforming grind
relief on a separate piston rod. The actions of AD 2010-19-51 were
intended to detect corrosion or a nonconforming piston rod that, if not
corrected, could result in the failure of the piston rod, failure of
the servo actuator, and subsequent loss of the helicopter.
Actions Since Existing AD Was Issued
Since we issued AD 2010-19-51 (75 FR 71540, November 24, 2010),
Transport Canada Civil Aviation (TCCA), which is the aviation authority
for Canada, issued Canadian AD No. CF-2010-29R1, dated July 26, 2012,
to correct an unsafe condition for Bell Model 222, 222B, 222U, 230, and
430 helicopters with servo actuator part number (P/N) 222-382-001-107.
TCCA AD No. CF-2010-29R1 supersedes AD No. CF-2010-29, dated August 26,
2010. The original TCCA AD required a one-time inspection of the servo
actuator for corrosion or a crack, and if needed, repair of the servo
actuator. AD No. CF-2010-29 also set intervals for a required overhaul
of the servo actuator, depending on the primer or plating on the piston
rod.
TCCA's subsequent AD No. CF-2010-29R1 requires an inspection of the
servo actuator and either overhauling or replacing the piston rod with
a stainless steel piston rod. Replacement of the piston rod extends the
overhaul interval of the servo actuator to 10,000 hours TIS or 10
years, whichever comes first. AD No. CF-2010-29R1 allows different
compliance times for overhaul or replacement of the piston rod,
depending on the condition of the piston rod when inspected.
FAA's Determination
These helicopters have been approved by the aviation authority of
Canada and are approved for operation in the United States. Pursuant to
our bilateral agreement with Canada, TCCA, its technical
representative, has notified us of the unsafe condition described in
its AD. We are proposing this AD because we evaluated all known
relevant information and determined that an unsafe condition is likely
to exist or develop on other products of the same type design.
Related Service Information
We reviewed Bell Alert Service Bulletin (ASB) 222-11-111 for Model
222 and 222B helicopters, ASB 222U-11-82 for Model 222U helicopters,
ASB 230-11-43 for Model 230 helicopters, and ASB 430-11-46 for Model
430 helicopters, all Revision A and all dated June 22, 2012. The ASBs
contain, and require compliance with, Woodward HRT Service Bulletin
141600-67-03, dated February 14, 2012, to upgrade the servo actuator by
replacing the piston rod and then re-identifying the servo actuator
dash number with ``-111FM.'' The compliance time for upgrading the
servo actuator varies depending on the color and amount of corrosion
found and type of plating on the piston rod. The Bell ASBs also provide
an alternative inspection and procedure for servo actuator P/N 222-382-
001-107 which have not reached certain hours TIS and where the servo
actuator cannot be upgraded.
TCCA classified these ASBs as mandatory and issued AD No. CF-2010-
29R1, dated July 26, 2012, to
[[Page 51125]]
ensure the continued airworthiness of these helicopters.
Proposed AD Requirements
This proposed AD would supersede AD 2010-19-51, Amendment 39-16523
(75 FR 71540, November 24, 2010) and would require within 5 hours time-
in-service (TIS), inspecting servo actuator, P/N 222-382-001-107, using
a 10X or higher power magnifying glass to determine whether the piston
rod has any pitting or penetration of the base metal.
If the piston rod has pitting or penetration of the base metal, the
proposed AD would require, before further flight, replacing the servo
actuator with servo actuator P/N 222-382-001-111 or P/N 222-382-001-
111FM. Thereafter, the proposed AD would require overhauling servo
actuator P/N 222-382-001-111 or P/N 222-382-001-111FM at intervals not
to exceed 10 years or 10,000 hours TIS, whichever comes first.
Differences Between the Proposed AD and the TCCA AD
This proposed AD differs from the TCCA AD as follows:
The TCCA AD sets three different timelines or time-in-service
requirements for the overhaul or upgrade of the applicable servo
actuators, depending on the damage and type of material applied to
protect the piston rod.
We would require replacing, before further flight, the piston rod
if it has pitting or any penetration of the base metal.
The TCCA AD requires returning parts to the manufacturer, and this
proposed AD would not.
Costs of Compliance
We estimate that this proposed AD would affect 146 helicopters of
U.S. Registry and that labor costs average $85 an hour. Based on these
estimates, we expect the following costs:
Inspecting the servo actuators would require 4 work-hours
for a labor cost of $340 per helicopter, and $49,640 for the U.S.
fleet.
Overhauling the servo actuators would require 8 work-hours
for a labor cost of $680. Parts would cost $11,900 for a total cost of
$12,580 per helicopter.
Replacing the servo actuators would require 8 hours work-
hours for a labor cost of $680. Parts would cost $35,700 for a total
cost of $36,380 per helicopter.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed, I certify this proposed regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska to the extent that
it justifies making a regulatory distinction; and
4. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Amendment 39-16523, 75 FR
71540, and adding the following new airworthiness directive (AD):
Bell Helicopter Textron: Docket No. FAA-2013-0734; Directorate
Identifier 2012-SW-080-AD.
(a) Applicability
This AD applies to Bell Helicopter Textron Canada (Bell) Model
222, 222B, 222U, 230, and 430 helicopters, with a main rotor
hydraulic servo actuator (servo actuator), part number (P/N) 222-
382-001-107, installed, certificated in any category.
(b) Unsafe Condition
This AD defines the unsafe condition as pitting or any other
penetration of the base metal on the output piston rod assembly.
This condition could lead to failure of the piston rod, failure of
the servo actuator, and subsequent loss of helicopter control.
(c) Affected ADs
This AD supersedes AD 2010-19-51, Amendment 39-16523 (75 FR
71540, November 24, 2010).
(d) Comments Due Date
We must receive comments by October 21, 2013.
(e) Compliance
You are responsible for performing each action required by this
AD within the specified compliance time unless it has already been
accomplished prior to that time.
(f) Required Actions
(1) Within 5 hours time-in-service (TIS), inspect servo
actuator, P/N 222-382-001-107, using a 10X or higher power
magnifying glass to determine whether the piston rod has any pitting
or penetration of the base metal.
(2) If the piston rod has pitting or any penetration of the base
metal, replace with servo actuator P/N 222-382-001-111 or P/N 222-
382-001-111FM, before further flight. Thereafter, overhaul servo
actuator P/N 222-382-001-111 or P/N 222-382-001-111FM at intervals
not to exceed 10 years or 10,000 hours TIS, whichever comes first.
(g) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Safety Management Group, FAA, may approve AMOCs
for this AD. Send your proposal to: Matt Wilbanks, Aviation Safety
Engineer, Rotorcraft Certification Office, Rotorcraft Directorate,
FAA, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone (817)
222-5110; email [email protected].
(2) For operations conducted under a 14 CFR part 119 operating
certificate or under 14 CFR part 91, subpart K, we suggest that you
notify your principal inspector, or lacking a principal inspector,
the manager of the local flight standards district office or
certificate holding district office before operating any aircraft
complying with this AD through an AMOC.
[[Page 51126]]
(h) Additional Information
(1) The subject of this AD is addressed in Transport Canada
Civil Aviation AD No. CF-2010-29R1, dated July 26, 2012. A copy of
this document is available for review in Docket No. FAA-2013-0734 on
the Internet at http://www.regulations.gov.
(2) Bell Alert Service Bulletin (ASB) No. 222-11-111 for Model
222 and 222B helicopters, ASB No. 222U-11-82 for Model 222U
helicopters, ASB No. 230-11-43 for Model 230 helicopters, and ASB
No. 430-11-46 for Model 430 helicopters, all Revision A and all
dated June 22, 2012, contain information to replace and overhaul the
servo actuator. You may review service information at the FAA,
Office of the Regional Counsel, Southwest Region, 2601 Meacham
Blvd., Room 663, Fort Worth, Texas 76137.
(i) Subject
Joint Aircraft Service Component (JASC) Code: 6730, Rotorcraft
Servo System.
Issued in Fort Worth, Texas, on August 12, 2013.
Kim Smith,
Directorate Manager, Rotorcraft Directorate, Aircraft Certification
Service.
[FR Doc. 2013-20309 Filed 8-19-13; 8:45 am]
BILLING CODE 4910-13-P