[Federal Register Volume 78, Number 186 (Wednesday, September 25, 2013)]
[Proposed Rules]
[Pages 58970-58973]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-23273]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0797; Directorate Identifier 2013-NM-007-AD]
RIN 2120-AA64
Airworthiness Directives; The Boeing Company Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for
certain The Boeing Company Model 767-300 and 767-300F series airplanes.
This proposed AD was prompted by reports of malfunctions in the flight
deck display units resulting in blanking, blurring, or loss of color on
the display. This proposed AD would require modification and
installation of components in the main equipment center. For certain
other airplanes this proposed AD would require modification,
replacement, and installation of flight deck air relief system (FDARS)
components. We are proposing this AD to prevent malfunctions of the
flight deck display units, which could affect the ability of the
flightcrew to read the displays for airplane attitude, altitude, or
airspeed, and consequently reduce the ability of the flightcrew to
maintain control of the airplane.
DATES: We must receive comments on this proposed AD by November 12,
2013.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For Boeing service information identified in this proposed AD,
contact Boeing Commercial Airplanes, Attention: Data & Services
Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone
206-544-5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced service
information at the FAA, Transport Airplane Directorate, 1601 Lind
Avenue SW., Renton, Washington. For information on the availability of
this material at the FAA, call 425-227-1221.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES
section. Comments will be available in the AD docket shortly after
receipt.
FOR FURTHER INFORMATION CONTACT: Francis Smith, Aerospace Engineer,
Cabin Safety and Environmental Controls Branch, ANM-150S, FAA, Seattle
Aircraft Certification Office, 1601 Lind Avenue SW., Renton, Washington
98057-3356; phone: 425-917-6596; fax: 425-917-6590; email:
[email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include ``Docket No. FAA-2013-0797;
Directorate Identifier 2013-NM-007-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the
[[Page 58971]]
closing date and may amend this proposed AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
We have received reports of malfunctions in flight compartment
display units on Model 767-300F airplanes. Operators of Model 767-300F
airplanes reported flight deck display unit malfunctions including
blanking, blurring, or loss of color caused by moisture or condensation
being collected inside the display units during operation in hot and
humid environments. The reports range from a malfunction in a single
display unit to malfunctions in multiple display units. Boeing is aware
of the likely causes of display unit malfunctions related to moisture
or condensation ingress. The most frequent instance was display units
being cold soaked by the air delivered from the air conditioning packs
by the electronic cooling system through the 3-way valve in hot and
humid conditions. Malfunctions of the flight deck display units, if not
corrected, could affect the ability of the flightcrew to read the
displays for airplane attitude, altitude, or airspeed, and consequently
reduce the ability of the flightcrew to maintain control of the
airplane.
Model 767-300 airplanes have an electronic cooling system design
similar to the electronic cooling system on the Model 767-300F
airplane; therefore, Model 767-300 airplanes might be subject to the
unsafe condition revealed on Model 767-300F airplanes.
Relevant Service Information
We reviewed the following service information.
Boeing Service Bulletin 767-21-0240, Revision 1, dated
November 12, 2009.
Boeing Service Bulletin 767-21-0244, Revision 1, dated
March 8, 2010.
Boeing Service Bulletin 767-21-0245, Revision 1, dated
September 30, 2010.
Boeing Alert Service Bulletin 767-21A0247, dated October
10, 2011.
Boeing Alert Service Bulletin 767-21A0253, dated October
12, 2012.
For information on the procedures and compliance times, see this
service information at http://www.regulations.gov by searching for
Docket No. FAA-2013-0797.
Concurrent Service Information
Boeing Service Bulletin 767-21-0240, Revision 1, dated November 12,
2009; and Boeing Service Bulletin 767-21-0244, Revision 1, dated March
8, 2010 (both for Model 767-300 series airplanes); specify prior or
concurrent accomplishment of Boeing Service Bulletin 767-31-0073, dated
October 12, 1995 (for certain Model 767-300 series airplanes).
Boeing Service Bulletin 767-21-0245, Revision 1, dated September
30, 2010 (for Model 767-300F series airplanes), specifies that if the
3-way valve control logic change in Boeing Service Bulletin 767-21-
0235, dated July 29, 2011, is done in concurrently with Boeing Service
Bulletin 767-21-0245, Revision 1, dated September 30, 2010, operators
only need to do the functional test in the Accomplishment Instructions
of Boeing Service Bulletin 767-21-0245, Revision 1, dated September 30,
2010.
Boeing Alert Service Bulletin 767-21A0247, dated October 10, 2011
(for Model 767-300F series airplanes), specifies prior or concurrent
accomplishment of Boeing Service Bulletin 767-21-0235, dated October 8,
2009; or Revision 1, dated July 29, 2011 (for certain Model 767-300F
series airplanes).
For information on the procedures, see this service information at
http://regulations.gov by searching for Docket No. FAA-2013-0797.
FAA's Determination
We are proposing this AD because we evaluated all the relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the same type design.
Proposed AD Requirements
This proposed AD would require accomplishing the actions specified
in the service information identified previously, except where Boeing
Service Bulletin 767-21-0240, Revision 1, dated November 12, 2009; and
Boeing Service Bulletin 767-21-0244, Revision 1, dated March 8, 2010;
specify installing carpet in the flight deck, this proposed AD would
not specifically require that action because it is not critical to
address the unsafe condition.
Costs of Compliance
We estimate that this proposed AD affects 43 airplanes of U.S.
registry.
We estimate the following costs to comply with this proposed AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Pressure switch installation, relay 16 work-hours x $85 per $6,979 $8,339 $183,458
replacement, wire routing (Boeing hour = $1,360. (22 airplanes)
Alert Service Bulletin 767-21A0247,
dated October 10, 2011).
Carpet, muffler, and drain tube 37 work-hours x $85 per 0 3,145 50,320
installation, relay removal and hour = $3,145. (16 airplanes)
installation, wire bundle changes
(Boeing Service Bulletin
767[dash]21-0240, dated November
12, 2009; and Boeing Service
Bulletin 767-21-0244, Revision 1,
dated March 8, 2010).
Wire bundle and relay changes, 14 work-hours x $85 per 1,148 2,338 11,690
install 2 diodes (Boeing Service hour = $1,190. (5 airplanes)
Bulletin 767-21-0245, Revision 1,
dated September 30, 2010).
Replace duct, install additional 76 work-hours x $85 per 55,663 N/A N/A
duct, valve, altitude switch, and hour = $6,460.
pitot tube (Boeing Alert Service
Bulletin 767-21A0253, dated October
12, 2012).
----------------------------------------------------------------------------------------------------------------
According to the manufacturer, some of the costs of this proposed
AD may be covered under warranty, thereby reducing the cost impact on
affected individuals. We do not control warranty coverage for affected
individuals. As a result, we have included all costs in our cost
estimate.
[[Page 58972]]
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979);
(3) Will not affect intrastate aviation in Alaska; and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
The Boeing Company: Docket No. FAA-2013-0797; Directorate Identifier
2013-NM-007-AD.
(a) Comments Due Date
We must receive comments by November 12, 2013.
(b) Affected ADs
None.
(c) Applicability
This AD applies to The Boeing Company Model 767-300 and 767-300F
series airplanes, certificated in any category; as identified in the
service information specified in paragraphs (c)(1) through (c)(5) of
this AD.
(1) Boeing Service Bulletin 767-21-0240, Revision 1, dated
November 12, 2009.
(2) Boeing Service Bulletin 767-21-0244, Revision 1, dated March
8, 2010.
(3) Boeing Service Bulletin 767-21-0245, Revision 1, dated
September 30, 2010.
(4) Boeing Alert Service Bulletin 767-21A0247, dated October 10,
2011.
(5) Boeing Alert Service Bulletin 767-21A0253, dated October 12,
2012.
(d) Subject
Joint Aircraft System Component (JASC)/Air Transport Association
(ATA) of America Code 2158, Air Conditioning.
(e) Unsafe Condition
This AD was prompted by reports of malfunctions in the flight
deck display units resulting in blanking, blurring, or loss of color
on the display. We are issuing this AD to prevent malfunctions of
the flight deck display units, which could affect the ability of the
flightcrew to read the displays for airplane attitude, altitude, or
airspeed, and consequently reduce the ability of the flightcrew to
maintain control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Modification, Replacement, and Installation of Flight Deck Air
Relief System (FDARS) Components
For Model 767-300F series airplanes as identified in Boeing
Alert Service Bulletin 767-21A0253, dated October 12, 2012: Within
72 months after the effective date of this AD, in the main equipment
center and the area under the left and right sides of the flight
deck door, replace the existing duct with a new duct, install new
FDARS components (including mounting brackets, ducts, orifice,
outlet valve, and screen), modify wiring, modify the relay
installation in panel P36, and install a new altitude switch and
pitot tube, in accordance with the Accomplishment Instructions of
Boeing Alert Service Bulletin 767-21A0253, dated October 12, 2012.
(h) Modification and Installation of Components in the Main Equipment
Center
(1) For Model 767-300F series airplanes as identified in Boeing
Alert Service Bulletin 767-21A0247, dated October 10, 2011: Within
72 months after the effective date of this AD, in the main equipment
center, install a new bracket on the E8 Engine Indication and Crew
Alerting System (EICAS) rack at station 266.5, install a new
pressure switch to the bracket at the E8 EICAS rack, make changes to
wire bundles W176, W596, W1114, W1702, W2000, replace relay K10355
with a new relay K10718, and flush the pitot static system, in
accordance with the Accomplishment Instructions of Boeing Alert
Service Bulletin 767-21A0247, dated October 10, 2011.
(2) For Model 767-300F series airplanes as identified in Boeing
Service Bulletin 767-21-0245, Revision 1, dated September 30, 2012:
Within 72 months after the effective date of this AD, in the main
equipment center, replace relay K10355 with a new relay K10718, add
two diodes in the E8 EICAS rack, and make changes to wire bundles
W0176, W596, W1702, W2000, and W2006, in accordance with the
Accomplishment Instruction of Boeing Service Bulletin 767-21-0245,
Revision 1, dated September 30, 2012, except as provided by
paragraph (i) of this AD.
(3) For Model 767-300 series airplanes as identified in Boeing
Service Bulletin 767-21-0240, Revision 1, dated November 12, 2009;
and Boeing Service Bulletin 767-21-0244, Revision 1, dated March 8,
2010: Within 72 months after the effective date of this AD, in the
main equipment center, install drain tubing and muffler assemblies,
change wire bundle W1718, change relays, placards, and wire bundle
W5075 in the P136 left relay panel, change wire bundle W2006 in the
E8 EICAS rack; and change wire bundle W1114 in the P50 electrical
systems card file; in accordance with the Accomplishment
Instructions of Boeing Service Bulletin 767-21-0240, Revision 1,
dated November 12, 2009; or Boeing Service Bulletin 767-21-0244,
Revision 1, dated March 8, 2010; as applicable.
(i) Exception to Paragraph (h) of This AD
For Model 767-300F series airplanes identified as Group 1
airplanes in Boeing Service Bulletin 767-21-0245, Revision 1, dated
September 30, 2010: If the 3-way valve control logic change in
Boeing Service Bulletin 767-21-0235, dated July 29, 2011, is done
prior to or concurrent with the actions required by paragraph (h)(2)
of this AD, operators need to do only the functional test of the
manifold interconnect valve control logic modification, in
accordance with the Accomplishment Instructions of Boeing Service
Bulletin 767-21-0245, Revision 1, dated September 30, 2010.
Operators do not need to do the other actions specified in the
Accomplishment Instructions of Boeing Service Bulletin 767-21-0245,
Revision 1, dated September 30, 2010, if the actions in the
Accomplishment Instructions in Boeing Service Bulletin 767-21-0235,
dated July 29, 2011, are done concurrently. If the functional test
fails, before further flight, do corrective actions that are
approved in accordance with
[[Page 58973]]
the procedures specified in paragraph (l) of this AD.
(j) Concurrent Requirements
For Model 767-300 series airplanes as identified in Boeing
Service Bulletin 767- 21-0240, Revision 1, dated November 12, 2009;
and Boeing Service Bulletin 767-21-0244, Revision 1, dated March 8,
2012: Prior to or concurrently with accomplishing the requirements
of paragraph (h)(3) of this AD, do all of the actions specified in
the Accomplishment Instructions of Boeing Service Bulletin 767-31-
0073, dated October 12, 1995.
(k) Credit for Previous Actions
This paragraph provides credit for the actions required by
paragraph (h)(2) of this AD, if those actions were performed before
the effective date of this AD using Boeing Service Bulletin 767-21-
0245, dated April 16, 2010, which is not incorporated by reference
in this AD.
(l) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Seattle Aircraft Certification Office (ACO),
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or local
Flight Standards District Office, as appropriate. If sending
information directly to the manager of the ACO, send it to the
attention of the person identified in paragraph (m)(1) of this AD.
Information may be emailed to: [email protected].
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair required by this AD if it is approved by the
Boeing Commercial Airplanes Organization Designation Authorization
(ODA) that has been authorized by the Manager, Seattle ACO to make
those findings. For a repair method to be approved, the repair must
meet the certification basis of the airplane, and the approval must
specifically refer to this AD.
(m) Related Information
(1) For more information about this AD, contact Francis Smith,
Aerospace Engineer, Cabin Safety and Environmental Controls Branch,
ANM-150S, FAA, Seattle Aircraft Certification Office, 1601 Lind
Avenue SW., Renton, Washington 98057-3356; phone: 425-917-6596; fax:
425-917-6590; email: [email protected].
(2) For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management,
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced
service information at the FAA, Transport Airplane Directorate, 1601
Lind Avenue SW., Renton, Washington. For information on the
availability of this material at the FAA, call 425-227-1221.
Issued in Renton, Washington, on September 16, 2013.
Ross Landes,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2013-23273 Filed 9-24-13; 8:45 am]
BILLING CODE 4910-13-P