[Federal Register Volume 78, Number 186 (Wednesday, September 25, 2013)]
[Proposed Rules]
[Pages 58982-58985]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-23274]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0796; Directorate Identifier 2013-NM-111-AD]
RIN 2120-AA64
Airworthiness Directives; The Boeing Company Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to supersede airworthiness directive (AD) 2013-07-
07, which applies to all The Boeing Company Model 737-600, -700, -700C,
-800, -900, and -900ER series airplanes. AD 2013-07-07 requires
inspecting to determine the part number of the attach pins of the
horizontal stabilizer rear spar, and replacing certain attach pins.
Since we issued AD 2013-07-07, we received inquiries from affected
operators regarding the parts installation limitation and prohibition,
and re-installation of certain attach pins that were removed for
inspection. This proposed AD would clarify the parts installation
limitation and prohibition, and would add a new requirement for certain
airplanes on which certain attach pins were installed. We are proposing
this AD to prevent premature failure of the attach pins, which could
cause reduced structural integrity of the horizontal stabilizer to
fuselage attachment, resulting in loss of control of the airplane.
DATES: We must receive comments on this proposed AD by November 12,
2013.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this AD, contact Boeing
Commercial Airplanes, Attention: Data & Services Management, P.O. Box
3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000,
extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com.
You may review copies of the referenced service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For
information on the availability of this material at the FAA, call 425-
227-1221.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES
section. Comments will be
[[Page 58983]]
available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Nancy Marsh, Aerospace Engineer,
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office,
1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6440; fax:
425-917-6590; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2013-0796;
Directorate Identifier 2013-NM-111-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
On March 28, 2013, we issued AD 2013-07-07, Amendment 39-17411 (78
FR 22182, April 15, 2013) (``AD 2013-07-07''), for all Model 737-600, -
700, -700C, -800, -900, and -900ER series airplanes. AD 2013-07-07
requires inspecting to determine the part number of the attach pins of
the horizontal stabilizer rear spar, and replacing certain attach pins.
For airplanes having line numbers 1 through 3534, AD 2013-07-07 also
prohibited installing attach pins having part number (P/N) 180A1612-3
or 180A1612-4 that have 56,000 or greater flight cycles, unless certain
actions had been done. AD 2013-07-07 resulted from reports of an
incorrect procedure used to apply the wear and corrosion protection
surface coating to attach pins of the horizontal stabilizer rear spar.
We issued AD 2013-07-07 to prevent premature failure of the attach
pins, which could cause reduced structural integrity of the horizontal
stabilizer to fuselage attachment, resulting in loss of control of the
airplane.
Actions Since AD 2013-07-07, Amendment 39-17411 (78 FR 22182, April 15,
2013) Was Issued
Since we issued AD 2013-07-07, Amendment 39-17411 (78 FR 22182,
April 15, 2013), we have received inquiries from affected operators
regarding the parts installation limitation and prohibition (i.e.,
paragraph (i)(1)) of AD 2013-07-07, and re-installation of certain
attach pins of the horizontal stabilizer rear spar removed for
inspection during maintenance.
We have re-reviewed our response to commenter Japan Airlines (JAL)
in AD 2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013), and
have determined it is necessary to provide further clarification. JAL
requested approval of re-installation of any non-discrepant attach pins
having P/N 180A1612-3 or 180A1612-4 removed for inspection during
maintenance.
We clarify that the term ``install,'' as used in AD 2013-07-07,
Amendment 39-17411 (78 FR 22182, April 15, 2013), can be interpreted as
meaning ``replace'' while remaining within the intent of AD 2013-07-07.
That is, by simply re-installing non-discrepant attach pins having P/N
180A1612-3 or 180A1612-4 on the same airplane from which they were
removed, the operator is not ``installing'' a new or different attach
pin. Therefore, no alternative method of compliance is necessary to re-
install non-discrepant attach pins having P/N 180A1612-3 or 180A1612-4
on the same airplane from which they were removed during maintenance
not associated with AD 2013-07-07.
To clarify paragraph (i)(1) of AD AD 2013-07-07, Amendment 39-17411
(78 FR 22182, April 15, 2013), for airplanes having line numbers 1
through 3534, we have removed that paragraph and have added new
paragraph (k) to this proposed AD. New paragraph (k) of this proposed
AD would provide for installation of a attach pin of the horizontal
stabilizer rear spar having P/N 180A1612-3 or 180A1612-4, provided it
is replaced with an attach pin having P/N 180A1612-7 or 180A1612-8
prior to the accumulation of 56,000 total flight cycles on the pin.
In addition, for those same airplanes, paragraph (i)(1) of AD 2013-
07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013), inadvertently
allowed installation of an attach pin having P/N 180A1612-3 or
180A1612-4, even though the attach pin had been replaced with an attach
pin having P/N 180A1612-7 or 180A1612-8, as required by paragraph (h)
of AD 2013-07-07. In light of this, we have added new paragraph (l) to
this proposed AD for those airplanes on which attach pins having P/N
180A1612-3 or 180A1612-4 were installed. New paragraph (l) of this
proposed AD would require replacement of those attach pins with attach
pins having P/N 180A1612-7 or 180A1612-8 prior to the accumulation of
56,000 total flight cycles on the attach pin, or within 1,000 flight
cycles on the airplane after the effective date of this AD, whichever
occurs later.
FAA's Determination
We are proposing this AD because we evaluated all the relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the same type design.
Proposed AD Requirements
This proposed AD would retain certain requirements of AD 2013-07-
07, Amendment 39-17411 (78 FR 22182, April 15, 2013). This proposed AD
would clarify the parts installation limitation and prohibition, and
would add a new requirement for certain airplanes on which certain
attach pins were installed.
Costs of Compliance
We estimate that this proposed AD affects 1,050 airplanes of U.S.
registry. The new proposed requirements add no significant economic
burden over that specified in AD 2013-07-07, Amendment 39-17411 (78 FR
22182, April 15, 2013). Those costs are repeated for the convenience of
affected operators, as follows:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per product operators
----------------------------------------------------------------------------------------------------------------
Inspection and attach pin 39 work-hours x Up to $6,312...... Up to $9,627...... Up to $10,108,350.
replacement [retained actions $85 per hour =
from AD 2013-07-07, Amendment $3,315.
39-17411 (78 FR 22182, April
15, 2013)].
----------------------------------------------------------------------------------------------------------------
[[Page 58984]]
According to the manufacturer, some of the costs of this proposed
AD may be covered under warranty, thereby reducing the cost impact on
affected individuals. We do not control warranty coverage for affected
individuals. As a result, we have included all costs in our cost
estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing airworthiness directive (AD)
2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013), and
adding the following new AD:
The Boeing Company: Docket No. FAA-2013-0796; Directorate Identifier
2013-NM-111-AD.
(a) Comments Due Date
The FAA must receive comments on this AD action by November 12,
2013.
(b) Affected ADs
(1) This AD supersedes AD 2013-07-07, Amendment 39-17411 (78 FR
22182, April 15, 2013).
(2) This AD affects certain requirements of AD 2004-05-19,
Amendment 39-13514 (69 FR 10921, March 9, 2004; corrected April 13,
2004 (69 FR 19313).
(c) Applicability
(1) This AD applies to all The Boeing Company Model 737-600, -
700, -700C, -800, -900, and -900ER series airplanes, certificated in
any category.
(2) Installation of Supplemental Type Certificate (STC)
ST00830SE (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/408E012E008616A7862578880060456C?OpenDocument&Highlight=st00830se)
does not affect the ability to accomplish the actions required by
this AD. Therefore, for airplanes on which STC ST00830SE is
installed, a ``change in product'' alternative method of compliance
(AMOC) approval request is not necessary to comply with the
requirements of 14 CFR 39.17. For all other AMOC requests, the
operator must request approval for an AMOC in accordance with the
procedures specified in paragraph (m) of this AD.
(d) Subject
Joint Aircraft System Component (JASC)/Air Transport Association
(ATA) of America Code 55, Stabilizers.
(e) Unsafe Condition
This AD was prompted by reports of an incorrect procedure used
to apply the wear and corrosion protection surface coating to attach
pins of the horizontal stabilizer rear spar. We are issuing this AD
to prevent premature failure of the attach pins, which could cause
reduced structural integrity of the horizontal stabilizer to
fuselage attachment, resulting in loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Retained Part Number Inspection
This paragraph restates the requirements of paragraph (g) of AD
2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013). For
airplanes having line numbers 1 through 3534 inclusive: Before the
accumulation of 56,000 total flight cycles, or within 3,000 flight
cycles after May 20, 2013 (the effective date of AD 2013-07-07),
whichever occurs later, inspect to determine the part number of the
attach pins of the horizontal stabilizer rear spar. A review of
airplane maintenance records is acceptable in lieu of this
inspection if the part number of the attach pin can be conclusively
determined from that review.
(h) Retained Replacement
This paragraph restates the requirements of paragraph (h) of AD
2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013). If,
during the inspection required by paragraph (g) of this AD, any
horizontal stabilizer rear spar attach pin has P/N 180A1612-3 or
180A1612-4, prior to the accumulation of 56,000 total flight cycles
on the pin, or within 3,000 flight cycles after May 20, 2013 (the
effective date of AD 2013-07-07), whichever occurs later, replace
with a new attach pin having P/N 180A1612-7 or 180A1612-8,
respectively, in accordance with the Accomplishment Instructions of
Boeing Special Attention Service Bulletin 737-55-1093, dated April
9, 2012.
(i) Retained Parts Installation Prohibition
This paragraph restates the requirements of paragraph (i)(2) of
AD 2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013). For
airplanes having line numbers 3535 and subsequent: As of May 20,
2013 (the effective date of AD 2013-07-07), no person may install an
attach pin of the horizontal stabilizer rear spar having P/N
180A1612-3 or 180A1612-4 on any airplane.
(j) Retained Terminating Action for AD 2004-05-19, Amendment 39 13514
(69 FR 10921, March 9, 2004; Corrected April 13, 2004 (69 FR 19313))
This paragraph restates the provisions of paragraph (j) of AD
2013-07-07, Amendment 39-17411 (78 FR 22182, April 15, 2013).
Accomplishment of the actions required by paragraphs (g) and (h) of
this AD terminates the requirements of paragraphs (a), (b), (c),
(d), and (e) of AD 2004-05-19, Amendment 39-13514 (69 FR 10921,
March 9, 2004; corrected April 13, 2004 (69 FR 19313)), for the rear
spar attach pins only.
(k) New Parts Installation Limitation
For airplanes having line numbers 1 through 3534 inclusive: As
of the effective date of this AD, an attach pin of the horizontal
stabilizer rear spar having P/N 180A1612-3 or 180A1612-4 may be
installed on an airplane, provided it is replaced with an attach pin
having P/N 180A1612-7 or 180A1612-8, as applicable, prior to the
accumulation of 56,000 total flight cycles on the attach pin. The
replacement must be done in accordance with the Accomplishment
Instructions of Boeing Special Attention Service Bulletin 737-55-
1093, dated April 9, 2012.
[[Page 58985]]
(l) New Attach Pin Replacement
For airplanes having line numbers 1 through 3534 inclusive on
which an attach pin of the horizontal stabilizer rear spar having P/
N 180A1612-7 or 180A1612-8 has been replaced with an attach pin
having P/N 180A1612-3 or 180A1612-4 before the effective date of
this AD: Prior to the accumulation of 56,000 total flight cycles on
the pin, or within 1,000 flight cycles on the airplane after the
effective date of this AD, whichever occurs later, replace the
attach pin having P/N 180A1612-3 or 180A1612-4 with an attach pin
having P/N 180A1612-7 or 180A1612-8, as applicable, in accordance
with the Accomplishment Instructions of Boeing Special Attention
Service Bulletin 737-55-1093, dated April 9, 2012.
(m) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Seattle Aircraft Certification Office, FAA, has
the authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the ACO, send it to the attention of the
person identified in paragraph (n)(1) of this AD. Information may be
emailed to 9-ANM-Seattle-ACO-AMOC-Requests-faa.gov.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair required by this AD if it is approved by the
Boeing Commercial Airplanes ODA that has been authorized by the
Manager, Seattle ACO, to make those findings. For a repair method to
be approved, the repair must meet the certification basis of the
airplane, and the approval must specifically refer to this AD.
(4) AMOCs approved previously in accordance with AD 2013-07-07,
Amendment 39-17411 (78 FR 22182, April 15, 2013), are approved as
AMOCs for the corresponding provisions of this AD.
(n) Related Information
(1) For more information about this AD, contact Nancy Marsh,
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft
Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-3356;
phone: 425-917-6440; fax: 425-917-6590; email: [email protected].
(2) For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management,
P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone
206-544-5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced
service information at the FAA, Transport Airplane Directorate, 1601
Lind Avenue SW., Renton, Washington. For information on the
availability of this material at the FAA, call 425-227-1221.
Issued in Renton, Washington, on September 17, 2013.
Ross Landes,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2013-23274 Filed 9-24-13; 8:45 am]
BILLING CODE 4910-13-P