[Federal Register Volume 78, Number 250 (Monday, December 30, 2013)]
[Notices]
[Pages 79423-79427]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2013-31268]
-----------------------------------------------------------------------
DEPARTMENT OF ENERGY
Office of Energy Efficiency and Renewable Energy
[Docket No. EERE-2013-BT-DET-0053]
Energy Efficiency Program for Industrial Equipment: Petition of
CSA Group for Classification as a Nationally Recognized Certification
Program for Small Electric Motors
AGENCY: Office of Energy Efficiency and Renewable Energy, Department of
Energy.
ACTION: Notice of petition and request for public comments.
-----------------------------------------------------------------------
SUMMARY: This notice announces receipt of a petition from CSA Group
(CSA) seeking classification as a nationally recognized certification
program under 10 CFR 431.447 and 431.448. In its petition, which
appears at the end of this notice, CSA provides documentation to help
substantiate its position that its certification program for small
electric motors satisfies the evaluation criteria for classification as
a nationally recognized certification
[[Page 79424]]
program that are specified in 10 CFR 431.447(b). This notice summarizes
the substantive aspects of these documents and requests public comments
on the merits of CSA's petition.
DATES: DOE will accept comments, data, and information with respect to
the CSA Petition until January 29, 2014.
ADDRESSES: You may submit comments, identified by docket number ``EERE-
2013-BT-DET-0053,'' by any of the following methods:
Federal eRulemaking Portal: http://www.regulations.gov.
Follow the instructions for submitting comments.
Email: [email protected].
Include the docket number EERE-2013-BT-DET-0053 in the subject line of
the message.
Mail: Ms. Brenda Edwards, U.S. Department of Energy,
Building Technologies Program, Mailstop EE-2J/1000 Independence Avenue
SW., Washington, DC 20585-0121. Telephone: (202) 586-2945. Please
submit one signed original paper copy.
Hand Delivery/Courier: Ms. Brenda Edwards, U.S. Department
of Energy, Building Technologies Program, 950 L'Enfant Plaza SW., Suite
600, Washington, DC 20024. Please submit one signed original paper
copy.
Docket: For access to the docket to review the background documents
relevant to this matter, you may visit the U.S. Department of Energy,
950 L'Enfant Plaza SW., Washington, DC 20024; (202) 586-2945, between
9:00 a.m. and 4:00 p.m., Monday through Friday, except Federal
holidays. Please call Ms. Brenda Edwards at the above telephone number
for additional information.
FOR FURTHER INFORMATION CONTACT: Mr. Lucas Adin, U.S. Department of
Energy, Building Technologies Program, Mail Stop EE-2J, Forrestal
Building, 1000 Independence Avenue SW., Washington, DC 20585-0121.
Telephone: (202) 287-1317. Email: [email protected].
Mr. Michael Kido, U.S. Department of Energy, Office of the General
Counsel, Mail Stop GC-71, Forrestal Building, 1000 Independence Avenue
SW., Washington, DC 20585-0103. Telephone: (202) 586-8145. Email:
[email protected].
SUPPLEMENTARY INFORMATION:
I. Background and Authority
Part C of Title III of the Energy Policy and Conservation Act
contains energy conservation requirements for, among other things,
electric motors and small electric motors, including test procedures,
energy efficiency standards, and compliance certification requirements.
42 U.S.C. 6311-6316.\1\ Section 345(c) of EPCA directs the Secretary of
Energy to require manufacturers of electric motors ``to certify through
an independent testing or certification program nationally recognized
in the United States, that [each electric motor subject to EPCA
efficiency standards] meets the applicable standard.'' 42 U.S.C.
6316(c).
---------------------------------------------------------------------------
\1\ For editorial reasons, upon codification in the U.S. Code,
Part C was re-designated Part A-1.
---------------------------------------------------------------------------
Regulations to implement this statutory directive are codified in
Title 10 of the Code of Federal Regulations Part 431 (10 CFR part 431)
at Sec. 431.36, Compliance Certification, Sec. 431.20, Department of
Energy recognition of nationally recognized certification programs, and
Sec. 431.21, Procedures for recognition and withdrawal of recognition
of accreditation bodies and certification programs. Sections 431.20 and
431.21 set forth the criteria and procedures for national recognition
of an energy efficiency certification program for electric motors by
the U.S. Department of Energy (``DOE'' or in context, ``the
Department''). With the support of a variety of interests, including
industry and energy efficiency advocacy groups, DOE published a final
rule on May 4, 2012, that established requirements for small electric
motors that are essentially identical to the criteria and procedures
for national recognition of an energy efficiency certification program
for electric motors. See 77 FR 26608, 26629 (discussing DOE's reasoning
for codifying parallel provisions for small electric motors at 10 CFR
431.447 and 431.448).
For a certification program to be classified by DOE as being
nationally recognized in the United States for the testing and
certification of small electric motors, the organization operating the
program must submit a petition to the Department requesting such
classification, in accordance with Sec. Sec. 431.447 and 431.448. In
sum, for the Department to grant such a petition, the certification
program must: (1) Have satisfactory standards and procedures for
conducting and administering a certification system, and for granting a
certificate of conformity; (2) be independent of small electric motor
manufacturers, importers, distributors, private labelers or vendors;
(3) be qualified to operate a certification system in a highly
competent manner; and (4) be expert in the test procedures and
methodologies in IEEE Standard 112-2004 Test Methods A and B, IEEE
Standard 114-2010, CSA Standard C390-10, and CSA C747 or similar
procedures and methodologies for determining the energy efficiency of
small electric motors, and have satisfactory criteria and procedures
for selecting and sampling small electric motors for energy efficiency
testing. 10 CFR 431.447(b).
Each petition requesting classification as a nationally recognized
certification program must contain a narrative statement explaining why
the organization meets the above criteria, include documentation that
supports the narrative statement, and be signed by an authorized
representative. 10 CFR 431.447(c).
II. Discussion
Pursuant to Sec. Sec. 431.447 and 431.448, on November 1, 2013,
CSA submitted to the Department a ``Petition for Recognition as a
Nationally Recognized Certification Program for small electric motors''
(``Petition'' or ``CSA Petition''). The Petition was accompanied by a
cover letter from CSA to the Department, and the petition itself
includes five separate sections--(1) Scope and Application, (2)
Overview of CSA Group, (3) Certification and Testing--Quality
Management System, (4) CSA Group's Motor Energy Efficiency Verification
Program--Product Directory, and (5) Examples of Other CSA Group
Accreditations. The petition included supporting documentation on these
subjects. Copies of the above documents have been placed in the docket.
Consistent with its regulations, the Department is soliciting
comments, data and information on whether it should grant the CSA
Petition. 10 CFR 431.448(b). Any person submitting written comments to
DOE with respect to the CSA Petition must also, at the same time, send
a copy of such comments to CSA. As provided under section 431.448(c),
CSA may submit to the Department a written response to any such
comments. After receiving any such comments and responses, the
Department will issue an interim and then a final determination on the
CSA Petition, in accordance with Sec. 431.448(d) and (e) of 10 CFR
part 431.
In particular, the Department is interested in obtaining comments,
data, and information respecting the following evaluation criteria:
(1) Whether CSA has satisfactory standards and procedures for
conducting and administering a certification system, including periodic
follow up activities to assure that basic models of small electric
motors continue to conform to the efficiency levels for which they were
certified, and for granting a certificate of conformity.
[[Page 79425]]
DOE is also interested in obtaining comments as to how rigorously CSA
operates its certification system under the guidelines contained in
ISO/IEC Guide 65, General requirements for bodies operating product
certification systems.
(2) Whether CSA is independent of small electric motor
manufacturers, importers, distributors, private labelers or vendors. To
meet this requirement it cannot be affiliated with, have financial ties
with, be controlled by, or be under common control with any such
entity.
(3) Whether CSA is expert in the content and application of the
test procedures and methodologies in IEEE Std 112-2004 Test Methods A
and B, IEEE Std 114-2010, CSA C390-10, and CSA C747 (incorporated by
reference, see 10 CFR 431.443) or similar procedures and methodologies
for determining the energy efficiency of small electric motors. DOE is
also interested in receiving comments on whether CSA's criteria and
procedures for the selection and sampling of electric motors tested for
energy efficiency are technically appropriate and statistically
rigorous.
Issued in Washington, DC, on December 23, 2013.
Kathleen B. Hogan,
Deputy Assistant Secretary for Energy Efficiency, Energy Efficiency and
Renewable Energy.
November 1, 2013
Mr. Lucas Adin, Assistant Secretary for Energy Efficiency and
Renewable Energy
U.S. Department of Energy, Forrestal Building, 1000 Independence Ave
SW, Washington, DC 20585-0121.
Subject: Petition for Recognition as a Nationally Recognized
Certification Program for small electric motors.
Dear Mr. Adin,
Please accept this letter and accompanying supporting material
as CSA Group's petition for recognition of our small motor energy
efficiency verification program to be classified as a nationally
recognized certification program in the United States, in accordance
with 10 CFR Part 431.
Enclosed please find three (3) binders, each containing the
required information for the Department of Energy (DOE) recognition
of nationally recognized certification programs described in
Sections 431.447 and 431.448 of 10 CFR Part 431, dated May 4, 2012.
Among the topics, this documentation package includes:
1. A guide describing our small motor energy efficiency
verification service program;
2. A general description of our quality management system
covering the essential elements of our standards and procedures for
operating a certification system;
3. CSA Group By-Laws and assurance of our independence and
influence from manufacturers, suppliers and vendors; and
4. Samples of CSA Group accreditations.
CSA Group has been offering a motor Energy Efficiency
Verification service program since 1992 in support of Canadian
Federal and Provincial Regulations and since 2002 for evaluation of
electric motor efficiencies to US DOE requirements. Key elements of
our program for confirming continued compliance of a motor with a
standard are (1) a detailed construction report for a motor on its
initial submission; (2) follow-up inspections to confirm consistency
of construction and markings; (3) annual re-testing; and (4)
challenge testing service. CSA Group is confident that our
organization and staff have proven experience in operation a
certification program in this area, and our certification system
procedures fully meet the evaluation criteria for us to be
classified by DOE as a nationally recognized certification program.
We, therefore, believe that this petition is in order and that it
can be processed without delay. Please let me know if you require
any further information.
Thank you very much for your consideration,
Rick Morrison P.Eng., Technical Manager, Energy Efficiency
Verification, CSA Group.
CSA Group, 178 Rexdale Boulevard, Toronto, ON, M9W 1R3, Canada
T: 416 747 4090
Petition for Recognition
Energy Efficiency Evaluation of Electric Motors to United States
Department of Energy Requirements Documented in 10 CFR 431--Subpart B
and Subpart X
Table of Contents
Section 1. Scope and Application
Section 2. Overview of CSA Group
--Letters of Patent
--Statement of Independence
--CSA By-Laws
--Annual Report
--Corporate Organization Chart
Section 3. Certification and Testing--Quality Management System
Section 4. CSA Group's Motor Energy Efficiency Verification Program
--Product Directory
Section 5--Examples of Other CSA Group Accreditations
Section 1--Scope and Application
Since 2002, CSA Group's electric motor (1 hp-500 hp) energy
efficiency verification program has been DOE listed as a nationally
recognized certification program. CSA Group is seeking scope
expansion to be classified as a nationally recognized certification
program in the United States under EPCA with respect to verifying
Small Electric Motor (1/4 hp-3 hp) efficiencies when applying the
following test procedures and standards:
(a) Test method B of ANSI/IEEE 112-2004, Test Procedure for
Polyphase Induction Motors and Generators;
(b) Test method of CSA C390-10, Test method, marking
requirements and energy efficiency levels for three-phase induction
motors;
(c) Test method of CSA C747-09. Energy efficiency test methods
for small motors.
(d) Test method of IEEE 114-2001, Test procedure for single-
phase induction motors.
(e) NEMA MG1-2009, Motors and Generators
Facilities
CSA Group Certification Facilities
CSA Group has facilities in Canada, in the United States, in
Europe and in the Far East. For your reference they are as follows:
------------------------------------------------------------------------
Area Address
------------------------------------------------------------------------
Montreal............................... 865 Ellingham Street, Pointe
Claire, PQ H9R 5E8
Toronto................................ 178 Rexdale Boulevard, Toronto,
Ontario M9W 1R3
Edmonton............................... 1707-94 Street NW, Edmonton, AB
T6N 1E6
Vancouver.............................. 13799 Commerce Parkway,
Richmond, BC V6V 2N9
Cleveland.............................. 8501 East Pleasant Valley Road,
Cleveland, OH 44131-5575
Irvine................................. 2805 Barranca Parkway, Irvine,
CA 92606-5114
Frankfurt.............................. Weism[uuml]llerstrasse 45,
60314 Frankfurt am Main,
Germany
Shanghai............................... 1st Floor, Building 4, Qilai
Industrial City, 889 Yishan
Road, Shanghai, 200233 China
------------------------------------------------------------------------
Designated Testing Facilities
As part of CSA Group's motor energy efficiency verification
program we are using our Toronto test facility and the Laboratoire
des Technologies de l'Energie of Hydro-Quebec, (LTE) for such
purposes as product qualification testing, re-testing, and challenge
testing. The facilities of Toronto are used for testing the full
range of motors from 0.25 up to 50 horsepower and the LTE facilities
are used for motors ranging 50 to 500 horsepower.
Summary of Section 1 Supporting Documentation
Section 1 of the CSA petition contained no supporting documents.
Section 2--Overview of CSA Group
Name and Address
CSA Group, 178 Rexdale Blvd., Toronto, Ontario, M9W 1R3
(Headquarters)
Background
CSA Group is an independent organization providing services in
the fields of Standards Development and Conformity Assessment. The
Standards Division of CSA Group is responsible for the
administration of the development of voluntary consensus based
standards, while the Certification and Testing Division provides
conformity assessment programs including laboratory testing
certification and inspection. The Consumer Product Evaluation
Division provides services for consumer product evaluation.
Canadian Standards Association, operating as CSA Group, was
established in 1919 as an independent, not-for-profit corporation
under Part II of the Canada Corporations Act. CSA Group is a
membership association whose
[[Page 79426]]
purpose is to make standards work for people and business. CSA Group
is the largest standards developer in Canada, certifies and tests
various products to standards which may be destined for retail
markets in Canada, the US and internationally, and tests consumer
products to retailer protocols. CSA Group has staff which includes
approximately 1100 employees in 14 offices across North America, as
well as over 7,000 members who volunteer their time and knowledge to
develop standards and programs that benefit business, industry and
society. CSA Group has sales of approximately $250M, is involved in
52 technologies, and has over 2,000 standards and over 88,000
customers.
Ownership
CSA Group is an independent, not-for-profit organization
governed by a Board of Directors selected by the membership. The
Association has no affiliation with manufacturers or suppliers of
the products submitted for certification. Attachment 1 provides
information regarding: (a) CSA's Letters of Patent; (b) Statement of
Independence; and (c) By-Laws.
Board of Directors and Principal Officers
See CSA Group's Annual Report for the individuals serving on our
Board of Directors and Executive Management Team. See Attachment 2.
Major components of the Association are shown on the ``Corporate
Organization Chart.'' See Attachment 3.
Summary of Section 2 Supporting Documentation
Section 2, Attachment 1, contains copies of: the Canadian
Engineering Standards Association Charter, dated January 21, 1919;
the Canadian Standards Association Supplementary Letters Patent,
dated April 26, 1944;
Section 2, Attachment 2, a sworn Statement of Independence,
dated October 16, 2013;
Section 2, Attachment 3, is a copy of the CSA Group 2012 Annual
Report.
Section 2, Attachment 4, is a copy of the CSA Group senior
management organization chart.
Section 3--CSA Group Certification Services Quality Management System
CSA Group's Certification Division maintains the quality
assurance system for the Association's worldwide operations. The
objective of this system is to ensure,
(a) technical excellence;
(b) consistency of interpretation, application of standards,
programs and procedures;
(c) integrity of our Mark; and
(d) continuous improvement.
The Quality Assurance system for the Division is based on
national and international accreditation requirements and specific
contractual customer requirements. The accreditation requirements
are found in the applicable editions of the following standards.
ISO/IEC Guide 65/General Requirements for Bodies Operating Product
Certification Systems
SCC/CAN-P3
SCC/CAN-P-1500 Additional Requirements for Accreditation of
Certification Bodies
ISO/IEC 17025/ General Requirements for the Competence of
Calibration and Testing Laboratories
SCC/CAN P-4
ANSI Z34.1 American National Standard for Certification--third party
certification program
CSA Group has implemented the requirements specified in ISO/IEC
Guide 65, General requirements for bodies operating product
certification systems. CSA Group facilities are accredited by
accreditation bodies such as Standard Council of Canada and ANSI to
these requirements.
Divisional Quality Documents (DQDs) are operating procedures and
guidelines used by staff in support of the quality assurance system.
Summary of CSA Group Section 3 Supporting Documentation
Section 3 of the CSA petition contained no supporting documents.
Section 4--CSA Group's Motor Energy Efficiency Verification Program
Overview of the CSA Verification Program:
Application
Evaluation and Testing
Certification
Service Agreement
Accompanying Services
Follow-up Inspections
Product Re-testing
Challenge Testing
Corrective Action
Sampling Process
Expertise in Motor Test Procedures
As Canada's premier Standards Development Organization, CSA
Group publishes consensus standards to improve products and enhance
trade--all the time ensuring the needs of our various Stakeholders
are met. By establishing consensus among the different interest
groups, with a balanced committee process, CSA Group creates
effective standards that are frequently referenced in Canadian
Energy Efficiency Regulations. In addition, US DOE electric motor
and small electric motor Regulations reference CSA Standards such as
C390-10 and C747-09.
CSA Standard C390-10, Test method, marking requirements and,
energy efficiency levels for three-phase induction methods, is
widely used in Canada as an integral part of Federal and Provincial
Regulations. Electrical utility programs also make use of this
standard to promote the use of higher levels of energy performance
on a voluntary basis.
Our intimate knowledge of the standard coupled with CSA Group's
recognition as an accredited Certification Organization in Canada
for motor efficiency and electrical safety supports the needs of
manufacturers, consumers and regulators. We provide the necessary
independent assurance that motors covered by government regulations
meet and continue to comply with the established energy efficiency
requirements.
Verification Program
The acceptance of motors under the CSA Group's energy efficiency
verification program depends upon the satisfactory evaluation and
testing to determine that the requirements of the applicable
standard (CSA Standard C390-10, C747-09) are met on a continuing
basis. The following is a description of the major elements of our
program used for qualifying manufacturers' motors or group of
motors.
Application
The customer makes an application requesting energy efficiency
verification for his motor and submits all required documentation
such as a list of all motors being submitted by model designation,
type, and applicable performance ratings. The application is given a
specific file to track and record all activities to the project. A
qualified person (e.g., professional engineer) is then assigned
responsibility for handling the project.
Evaluation and Testing
CSA Group with the manufacturer's assistance prepares a motor
control list, identifying the critical features and the controls for
these features for maintaining consistent performance with respect
to energy efficiency. Representative motor samples are tested by an
acceptable facility such as CSA Group or LTE to verify manufacturers
rated efficiency values.
Attachment 1 provides a description of the procedures used for
the initial motor qualification testing and the follow-up re-testing
service to ensure continued compliance. A findings letter is then
issued giving the results of our evaluation and actions needed, if
applicable, to meet the standard. Modified samples may be required
for further examination and testing.
Certification
After the resolution of all the action items and all the
conditions of the standard are met, the applicant is formally
authorized to apply the CSA Group Energy Efficiency Verification
Mark. A report is prepared describing the product and giving the
related test results. A directory listing all products verified for
energy efficiency is published and available to the general public.
See Attachment 2.
Service Agreement
The applicant authorized to represent its motor as verified with
our Energy Efficiency Marking must enter a signed agreement with CSA
Group. This agreement addresses the conditions for maintaining
certification such as access to facilities and records, follow-up
inspection, product re-testing and challenge testing. Manufacturers
are also required to notify CSA Group when changes are made to the
motor, which may affect their performance rating. These terms and
conditions are designed to protect the integrity of our Energy
Efficiency Marking.
Accompanying Services
After the motor has been initially evaluated and found to comply
with the standard, our program includes additional services to
ensure that motors bearing the CSA Group verification marking
continue to meet the applicable requirements. These services are:
(a) Follow-up inspections;
[[Page 79427]]
(b) Product re-testing; and
(c) Challenge testing.
Follow-up Inspections
Follow-up inspections are conducted at the point of
manufacturing each year to ensure that,
(a) our mark is only applied to motors that have been verified
for energy efficiency;
(b) the manufacturers' product control measures are continuing
to produce marked products that are in compliance with our report
and the standard;
(c) samples required for re-testing are selected and sealed by
CSA Group staff during these visits.
Product Re-testing
Although a report is generated for motors detailing the critical
construction features needed for maintaining consistent performance
with respect to energy efficiency, our program is supplemented with
unannounced motor re-testing to the specified requirement. This
facilitates continued compliance with the standard and maintains the
integrity of our mark.
Challenge Testing
Another service--challenge testing--is offered to any
manufacturer or other party wishing to confirm the motor efficiency
rating of a verified motor. This feature assists in ensuring the
integrity of our verification program and can lead to the motor
efficiency de-rating or a delisting of a series of motors
represented by the sample motor.
Corrective Action
When a motor fails to comply with the standards, we take the
following steps:
(a) remove the verification mark from the affected motor or
motors;
(b) delist the motor(s);
(c) notify the applicable regulatory authorities and government
departments of noncompliant motors (i.e., serial number, date code,
or equivalent);
(d) re-test and verify the motor efficiency rating after the
manufacturer modifies the product.
Sampling Process
The objective of our sampling process is to minimize
manufacturers' tests, costs and time to market, while providing
sufficient confidence that the series of motors verified meet the
applicable energy efficiency standard. The added features of our
program such as unannounced follow-up inspections, random motor re-
testing and challenge testing are critical components for
demonstrating continued compliance to the standard. As a consequence
of our CSA Group's continual surveillance, the following sampling
process guideline has emerged.
Samples Required For Motor Model Qualification Testing
Test 5 units of each 5 basic motor model type (total of 25
motors). The efficiency of the sample lot must equal or exceed the
required nominal full load efficiency rating. The individual sample
efficiencies must comply with the nominal efficiency tolerance
required by the Standard. Manufacturer's information indicating
efficiency ratings must be in agreement with CSA Group's records.
Selection of Basic Model Types To Represent a Series of Motors
A minimum of five (5) basic model types are required to be
tested to verify the efficiency ratings of a series of motors. The
basic model types are to be selected such that they represent the
complete range of motors within the series. This may require that
more than 5 basic model types are selected. High volume production
motors are to be represented in the basic model types selected.
Samples Required For Scheduled Motor Re-testing
A goal for verifying continued compliance with the standard is
to re-test high volume motors at least once every 2 years. Other
motors of different frame series are to be retested as needed to
ensure continued compliance.
The initial sample lot shall consist of one motor. If the result
equals or exceeds the minimum result from the qualification tests,
then no further samples are required. If the result is less than the
minimum result from the qualifying tests, then select motor samples
per the qualifying test procedure.
Expertise in Motor Test Procedures
CSA Group has been active in the certification for safety of
electric motors since before 1940 and has more than 450
certification listings active at this time.
CSA Group has been offering the Energy Efficiency Verification
Service for Electric Motors since 1992 with motor size from 1 to 500
hp. The motor efficiency is tested to Standards CSA C390-10, IEEE
112-2004, IEEE 114 and CSA 747-09. CSA has obtained accreditation
from DOE in 2002 for motor efficiency US Department of Energy as a
nationally recognized certification program in 2002 (Federal
Register/Vol 67, No 249/Friday December 27, 2002/Notices).
Summary of CSA Group Section 4 Supporting Documentation
Section 4, Attachment 1, contains a copy of an information
letter to ``All Manufacturers of AC Three Phase Induction Motors
Rated 1 hp to 500 hp,'' which is entitled ``Announcing CSA Standard
C390-10 Test methods, marking requirements and energy efficiency
levels for three-phase induction motors, 4th edition.''
Section 5--Examples of Other CSA Group Accreditations
The certification system and technical capabilities of the
Association have enabled CSA Group to be accredited nationally and
internationally for a wide product spectrum such as electrical
safety, energy efficiency, plumbing and gas. See Attachment 1 for
examples of accreditations CSA Group has received.
Qualification of CSA Group To Operate as a Certification System
The U.S. Department of Energy recognized the Energy Efficiency
Verification Service of CSA Group as a Nationally Recognized
certification Program in a Federal Register Notice dated 27 December
2002 (67 FR 79480).
Summary of CSA Group Section 5 Supporting Documentation
Section 5, Attachment 1, contains copies of the following
documents CSA Group has received in recognition of its certification
system and technical capabilities:
1. Certificate of Accreditation under the Certification Body
Accreditation Program, from the Standard Council of Canada, June 27,
2013;
2. Certificate of Accreditation in recognition of being an
Accredited Testing organization, from the International
Accreditation Service, November 1, 2012.
3. Certificate of Recognition as a Nationally Recognized Testing
Laboratory, from the Occupational Safety and Health Administration,
effective through December 31, 2014.
[FR Doc. 2013-31268 Filed 12-27-13; 8:45 am]
BILLING CODE 6450-01-P