[Federal Register Volume 79, Number 32 (Tuesday, February 18, 2014)]
[Proposed Rules]
[Pages 9318-9378]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-02714]
[[Page 9317]]
Vol. 79
Tuesday,
No. 32
February 18, 2014
Part II
Environmental Protection Agency
-----------------------------------------------------------------------
40 CFR Part 51
Promulgation of Air Quality Implementation Plans; Arizona; Regional
Haze and Interstate Visibility Transport Federal Implementation Plan;
Proposed Rule
Federal Register / Vol. 79 , No. 32 / Tuesday, February 18, 2014 /
Proposed Rules
[[Page 9318]]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Part 51
[EPA-R09-OAR-2013-0588, FRL-9906-30-Region 9]
Promulgation of Air Quality Implementation Plans; Arizona;
Regional Haze and Interstate Visibility Transport Federal
Implementation Plan
AGENCY: Environmental Protection Agency (EPA).
ACTION: Proposed rule.
-----------------------------------------------------------------------
SUMMARY: This proposed Federal Implementation Plan (FIP) addresses the
requirements of the Regional Haze Rule (RHR) and interstate visibility
transport for the disapproved portions of Arizona's Regional Haze (RH)
State Implementation Plan (SIP) as described in our final rule
published on July 30, 2013. Our final rule on Arizona's RH SIP
partially approved and partially disapproved the State's plan to
implement the regional haze program for the first planning period.
Today's proposed rule addresses the RHR's requirements for Best
Available Retrofit Technology (BART), Reasonable Progress Goals (RPGs)
and Long-term Strategy (LTS) as well as the interstate visibility
transport requirements for pollutants that affect visibility in
Arizona's 12 Class I areas as well as areas in nearby states. The BART
sources addressed in this proposed FIP are Tucson Electric Power (TEP)
Sundt Generating Station Unit 4, Lhoist Nelson Lime Plant Kilns 1 and
2, ASARCO Incorporated Hayden Smelter, and Freeport-McMoran Inc. (FMMI)
Miami Smelter. The sources with proposed controls for reasonable
progress are the Phoenix Cement Clarkdale Plant and the CalPortland
Cement Rillito Plant.
DATES: Written comments must be submitted to the designated contact at
the address in the General Information section of SUPPLEMENTARY
INFORMATION on or before March 31, 2014.
ADDRESSES: See the General Information section of SUPPLEMENTARY
INFORMATION for further instructions on where and how to learn more
about this proposal, attend a public hearing, or submit comments.
FOR FURTHER INFORMATION CONTACT: Thomas Webb, U.S. EPA, Region 9,
Planning Office, Air Division, Air, 75 Hawthorne Street, San Francisco,
CA 94105. Thomas Webb may be reached at telephone number (415) 947-4139
and via electronic mail at [email protected].
SUPPLEMENTARY INFORMATION:
Table of Contents
I. General Information
A. Definitions
B. Docket
C. Instructions for Submitting Comments to EPA
D. Submitting Confidential Business Information
E. Tips for Preparing Your Comments
F. Public Hearings
II. Proposed Actions Background and Overview
A. Background
B. Regional Haze
C. Interstate Transport of Pollutants That Affect Visibility
III. Review of State and EPA Actions on Regional Haze
A. EPA's Schedule To Act on Arizona's RH SIP
B. History of State Submittals and EPA Actions
C. EPA's Authority To Promulgate a FIP
IV. EPA's BART Process
A. BART Factors
B. Visibility Analysis
C. Explanation of Visibility Tables
V. EPA's Proposed BART Analyses and Determinations
A. Sundt Generating Station Unit 4
B. Nelson Lime Plant Kilns 1 and 2
C. Hayden Smelter
D. Miami Smelter
VI. EPA's Proposed Reasonable Progress Analyses and Determinations
A. Reasonable Progress Analysis of Point Sources for
NOX
B. Reasonable Progress Analysis of Area Sources for
NOX and SO2
C. Reasonable Progress Goals
D. Meeting the Uniform Rate of Progress
VII. EPA's Proposed Long-Term Strategy Supplement
A. Emission Reductions for Out-of-State Class I Areas
B. Emissions Limitations and Schedules for Compliance To Achieve
RPGs
C. Enforceability of Emissions Limitations and Control Measures
D. Proposed Partial LTS FIP
VIII. EPA's Proposal for Interstate Transport
IX. Summary of Proposed Actions
A. Regional Haze
B. Interstate Transport
X. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
B. Paperwork Reduction Act
C. Regulatory Flexibility Act
D. Unfunded Mandates Reform Act
E. Executive Order 13132: Federalism
F. Executive Order 13175: Consultation and Coordination With
Indian Tribal Governments
G. Executive Order 13045: Protection of Children From
Environmental Health Risks and Safety Risks
H. Executive Order 13211: Actions That Significantly Affect
Energy Supply, Distribution, or Use
I. National Technology Transfer and Advancement Act
J. Executive Order 12898: Federal Actions To Address
Environmental Justice in Minority Populations and Low-Income
Populations
K. Congressional Review Act
I. General Information
A. Definitions
(1) The words or initials Act or CAA mean or refer to the Clean Air
Act, unless the context indicates otherwise.
(2) The initials ADEQ mean or refer to the Arizona Department of
Environmental Quality.
(3) The words Arizona and State mean the State of Arizona.
(4) The initials BACT mean or refer to Best Available Control
Technology.
(5) The initials BART mean or refer to Best Available Retrofit
Technology.
(6) The initials BOD mean or refer to boiler operating day.
(7) The term Class I area refers to a mandatory Class I Federal
area.
(8) The initials CEMS refers to continuous emission monitoring
system or systems.
(9) The initials dv mean or refer to deciview, a measure of visual
range.
(10) The words EPA, we, us or our mean or refer to the United
States Environmental Protection Agency.
(11) The initials FGD mean or refer to flue gas desulfurization.
(12) The initials FIP mean or refer to Federal Implementation Plan.
(13) The initials FLM mean or refer to Federal Land Managers.
(14) The initials IMPROVE mean or refer to Interagency Monitoring
of Protected Visual Environments monitoring network.
(15) The initials IPM mean or refer to Integrated Planning Model.
(16) The initials lb/MMBtu mean or refer to pounds per one million
British thermal units.
(17) The initials LDSCR and HDSCR mean or refer to low and high
dust Selective Catalytic Reduction, respectively.
(18) The initials LNB mean or refer to low NOX burners.
(19) The initials LTS mean or refer to Long-term Strategy.
(20) The initials MACT mean or refer to Maximum Achievable Control
Technology.
(21) The initials MW mean or refer to megawatts.
(22) The initials NAAQS mean or refer to National Ambient Air
Quality Standards.
(23) The initials NEI mean or refer to National Emissions
Inventory.
(24) The initials NESCAUM mean or refer to Northeast States for
Coordinated Air Use Management.
(25) The initials NM mean or refer to National Monument.
(26) The initials NOX mean or refer to nitrogen oxides.
[[Page 9319]]
(27) The initials NP mean or refer to National Park.
(28) The initials NPS mean or refer to the National Park Service.
(29) The initials NSCR mean or refer to non-selective catalytic
reduction.
(30) The initials NSPS mean or refer to new source performance
standards.
(31) The initials PM mean or refer to particulate matter.
(32) The initials PM2.5 mean or refer to fine particulate matter
with an aerodynamic diameter of less than 2.5 micrometers.
(33) The initials PM10 mean or refer to particulate matter with an
aerodynamic diameter of less than 10 micrometers.
(34) The initials PSAT mean or refer to Particulate Source
Apportionment Technology.
(35) The initials PSD mean or refer to Prevention of Significant
Deterioration.
(36) The initials PTE mean or refer to potential to emit.
(37) The initials RH mean or refer to regional haze.
(38) The initials RHR mean or refer to the Regional Haze Rule,
originally promulgated in 1999 and codified at 40 CFR 51.301-309.
(39) The initials RMC mean or refer to Regional Modeling Center.
(40) The initials RP mean or refer to Reasonable Progress.
(41) The initials RPG or RPGs mean or refer to Reasonable Progress
Goal(s).
(42) The initials SCR mean or refer to Selective Catalytic
Reduction.
(43) The initials SIP mean or refer to State Implementation Plan.
(44) The initials SNCR mean or refer to Selective Non-catalytic
Reduction.
(45) The initials SO2 mean or refer to sulfur dioxide.
(46) The initials SOFA mean or refer to Separated Overfire Air.
(47) The initials SRP mean or refer to Salt River Project
Agricultural Improvement and Power District.
(48) The initials tpy mean tons per year.
(49) The initials TSD mean or refer to Technical Support Document.
(50) The initials TSF mean or refer to tons of stone feed.
(51) The initials ULNB mean or refer to ultra-low NOX
burners.
(52) The initials URP mean or refer to Uniform Rate of Progress.
(53) The initials VOC mean or refer to volatile organic compounds.
(54) The initials WRAP mean or refer to the Western Regional Air
Partnership.
B. Docket
This proposed action relies on documents, information and data that
are listed in the index on http://www.regulations.gov under docket
number EPA-R09-OAR-2013-0588. Previous proposed and final actions
regarding Arizona's RH SIP are under docket number EPA-R09-OAR-2012-
0904 and EPA-R09-OAR-2012-0021. Although listed in the index, some
information is not publicly available (e.g., Confidential Business
Information (CBI)). Certain other material, such as copyrighted
material, is publicly available only in hard copy form. Publicly
available docket materials are available either electronically at
http://www.regulations.gov or in hard copy at the Planning Office of
the Air Division, AIR-2, EPA Region 9, 75 Hawthorne Street, San
Francisco, CA 94105. EPA requests that you contact the individual
listed in the FOR FURTHER INFORMATION CONTACT section to view the hard
copy of the docket. You may view the hard copy of the docket Monday
through Friday, 9-5 PST, excluding Federal holidays.
C. Instructions for Submitting Comments to EPA
Written comments must be submitted on or before March 31, 2014.
Submit your comments, identified by Docket ID No. EPA-R09-OAR-2013-
0588, by one of the following methods:
Federal Rulemaking portal: http://www.regulations.gov.
Follow the on-line instructions for submitting comments.
Email: [email protected].
Fax: 415-947-3579 (Attention: Thomas Webb).
Mail, Hand Delivery or Courier: Thomas Webb, EPA Region 9,
Air Division (AIR-2), 75 Hawthorne Street, San Francisco, California
94105. Hand and courier deliveries are only accepted Monday through
Friday, 8:30 a.m. to 4:30 p.m., excluding Federal holidays. Special
arrangements should be made for deliveries of boxed information.
EPA's policy is to include all comments received in the public
docket without change.
We may make comments available online at http://www.regulations.gov,
including any personal information provided, unless the comment
includes information claimed to be CBI or other information for which
disclosure is restricted by statute. Do not submit information that you
consider to be CBI or that is otherwise protected through http://www.regulations.gov or email. The http://www.regulations.gov Web site
is an ``anonymous access'' system, which means EPA will not know your
identity or contact information unless you provide it in the body of
your comment. If you send an email comment directly to EPA, without
going through http://www.regulations.gov, we will include your email
address as part of the comment that is placed in the public docket and
made available on the Internet. If you submit an electronic comment,
EPA recommends that you include your name and other contact information
in the body of your comment and with any disk or CD-ROM you submit. If
EPA cannot read your comment due to technical difficulties and cannot
contact you for clarification, EPA may not be able to consider your
comment. Electronic files should not include special characters or any
form of encryption, and be free of any defects or viruses.
D. Submitting Confidential Business Information
Do not submit CBI to EPA through http://www.regulations.gov or
email. Clearly mark the part or all of the information that you claim
as CBI. For CBI information in a disk or CD ROM that you mail to EPA,
mark the outside of the disk or CD ROM as CBI and identify
electronically within the disk or CD ROM the specific information that
is claimed as CBI. In addition to one complete version of the comment
that includes information claimed as CBI, you must submit a copy of the
comment that does not contain the information claimed as CBI for
inclusion in the public docket. We will not disclose information so
marked except in accordance with procedures set forth in 40 CFR part 2.
E. Tips for Preparing Comments
When submitting comments, remember to:
Identify the rulemaking by docket number and other
identifying information (e.g., subject heading, Federal Register date
and page number).
Explain why you agree or disagree; suggest alternatives
and substitute language for your requested changes.
Describe any assumptions and provide any technical
information and/or data that you used.
If you estimate potential costs or burdens, explain how
you arrived at your estimate in sufficient detail to allow for it to be
reproduced.
Provide specific examples to illustrate your concerns, and
suggest alternatives.
Explain your views as clearly as possible, avoiding
profanity or personal threats.
Make sure to submit your comments by the identified
comment period deadline.
To provide opportunities for questions and discussion, EPA will
hold an open house prior to the public hearing. During the open house,
EPA staff will be available informally to
[[Page 9320]]
answer questions on our proposed rule. Any comments made to EPA staff
during the open house must still be provided formally in writing or
orally during a public hearing to be considered in the record. The open
house and public hearing schedule is as follows.
F. Public Hearings
EPA will hold two public hearings at the dates, times and locations
stated below to accept oral and written comments into the record. To
request interpretation services or to request reasonable accommodation
for a disability, please contact the person in the FOR FURTHER
INFORMATION CONTACT section by February 14, 2014.
Public Hearing in Phoenix:
Date: February 25, 2014.
Open House: 4-5 p.m.
Public Hearing: 6-8 p.m.
Location: Phoenix Convention Center, Rooms 150-153, 33 South 3rd
Street, Phoenix, Arizona 85004.
Public Hearing in Tucson:
Date: February 26, 2014.
Open House: 4-5 p.m.
Public Hearing: 6-8 p.m.
Location: Tucson High Magnet School, Auditorium, 400 North 2nd
Avenue, Tucson, Arizona 85705.
The public hearing will provide the public with an opportunity to
present views or information concerning the proposed RH FIP for
Arizona. EPA may ask clarifying questions during the oral
presentations, but will not respond to the presentations at that time.
We will consider written statements and supporting information
submitted during the comment period with the same weight as any oral
comments and supporting information presented at the public hearing.
Please consult section I.C, I.D and I.E of this preamble for guidance
on how to submit written comments to EPA. We will include verbatim
transcripts of the hearing in the docket for this action. The EPA
Region 9 Web site for the rulemaking, which includes the proposal and
information about the public hearing, is at http://www.epa.gov/region9/air/actions.
II. Proposed Actions Background and Overview
A. Background
The Clean Air Act (CAA) establishes as a national goal the
prevention of any future, and the remedying of any existing man-made
impairment of visibility in 156 national parks and wilderness areas
designated as Class I areas. Arizona has a wealth of such areas. The
sources addressed in this FIP affect many Class I areas in the State of
Arizona and adjacent states. This FIP will ensure that progress is made
toward natural visibility conditions at these national treasures, as
Congress intended when it directed EPA to improve visibility in
national parks and wilderness areas. Please refer to our previous
rulemaking on the Arizona RH SIP for additional background regarding
the CAA, regional haze and EPA's RHR.\1\
---------------------------------------------------------------------------
\1\ 77 FR 75704, 75707-75702 (December 21, 2012).
---------------------------------------------------------------------------
B. Regional Haze
We propose to promulgate a FIP as described in this notice and
summarized in this section to address those portions of Arizona's RH
SIP that we disapproved on July 30, 2013.\2\ We disapproved in part
Arizona's BART control analyses and determinations for four sources,
Reasonable Progress Goal (RPG) analyses and determinations, and Long-
term Strategy (LTS) for making reasonable progress. The proposed FIP
includes emission limits, compliance schedules and requirements for
equipment maintenance, monitoring, testing, recordkeeping and reporting
for all affected sources and units. The regulatory language for the
proposed FIP requirements is under Part 52 at the end of this notice.
---------------------------------------------------------------------------
\2\ 78 FR 46142.
---------------------------------------------------------------------------
1. Proposed BART Determinations
EPA conducted BART analyses and determinations for four sources:
Sundt Generating Station Unit 4, Nelson Lime Plant Kilns 1 and 2,
Hayden Smelter and Miami Smelter. The results of our BART evaluations
are summarized here for each source and are shown in Table 1. We are
seeking comments on our proposals.
Sundt: We propose that Sundt Unit 4 is BART-eligible and subject to
BART for sulfur dioxide (SO2), nitrogen oxides
(NOX) and particulate matter with aerodynamic diameter less
than 10 micrometers (PM10). For NOX, we propose
an emission limit of 0.36 lb/MMBtu as BART based upon an annual
capacity factor of 0.49, which is consistent with the use of Selective
Non-Catalytic Reduction (SNCR) as a control technology. For
SO2, we propose an emission limit of 0.23 lb/MMBtu as BART
on a 30-day boiler operating day (BOD) rolling basis, which is
consistent with dry sorbent injection (DSI) as a control technology.
For PM10, we propose a filterable PM10 emission
limit of 0.030 lb/MMBtu as BART based on the use of the existing fabric
filter baghouse. We also are proposing a switch to natural gas as a
better-than-BART alternative to the other proposed controls for all
three pollutants.
Nelson Lime Plant: We propose that Nelson Lime Kilns 1 and 2 are
subject to BART for NOX, SO2 and PM10.
For NOX, we propose a BART emission limit at Kiln 1 of 3.80
lb/ton lime and at Kiln 2 of 2.61 lb/ton lime on a 30-day rolling basis
as verified by continuous emission monitoring systems (CEMS). This
emission limit is consistent with the use of low-NOX burners
(LNB) and SNCR as control technologies. We propose that BART for
SO2 is an emission limit of 9.32 lb/ton for Kiln 1 and 9.73
lb/ton for Kiln 2 on a 30-day rolling basis, which is consistent with
the use of a lower sulfur fuel blend. For PM10, we propose a
BART emission limit of 0.12 lb/tons of stone feed (TSF) to control
PM10 at Kilns 1 and 2 based on the use of the existing
fabric filter baghouses. This level of control is commensurate with the
MACT standard that applies to this source.
Hayden Smelter: We propose that the Hayden Smelter is subject to
BART for NOX, and propose BART emission limits for
NOX and SO2. EPA previously approved the State's
determination that the Hayden Smelter is subject to BART for
SO2. For NOX, we propose to find that controlling
emissions from the converters and anode furnaces is cost-effective, but
would not result in sufficient visibility improvement to warrant the
cost. Therefore, we are proposing an annual emission limit of 40 tpy
NOX emissions from the BART-eligible units, which is
consistent with current emissions from these units. For SO2
from the converters, we propose a BART control efficiency of 99.8
percent on a 30-day rolling basis on all SO2 captured by
primary and secondary control systems, which can be achieved with a new
double contact acid plant. For SO2 from the anode furnaces,
we propose to find that controlling the 37 tons per year (tpy) of
SO2 emissions from these furnaces, while cost-effective, is
not warranted as BART given the potential for only minimal visibility
improvement. We propose as an emission limitation for the anode furnace
a work practice standard requiring that the furnaces only be charged
with blister copper or higher purity copper. We previously approved
Arizona's determination that BART for PM10 at the Hayden
Smelter is no additional controls. In order to ensure the
enforceability of this determination, we are proposing to incorporate
emission limitations and associated compliance requirements from the
National Emission Standard for Hazardous Air Pollutants (NESHAP) for
[[Page 9321]]
Primary Copper Smelting at 40 CFR Part 63, Subpart QQQ, as part of the
LTS.
Miami Smelter: EPA proposes that the Miami Smelter is subject to
BART for NOX, and proposes BART emission limits for
NOX and SO2. EPA previously approved the State's
determination that the Miami Smelter is subject to BART for
SO2. For NOX, we propose to find that controlling
the small amount of emissions from the converters and electric furnace
is cost-effective, but would not result in sufficient visibility
improvement to warrant the cost. Therefore, we are proposing an annual
emission limit of 40 tpy NOX emissions from the BART-
eligible units, which is consistent with current emissions. For
SO2 from the converters, we propose a BART control
efficiency of 99.7 percent on a 30-day rolling basis on all
SO2 emissions captured by the primary and secondary control
systems as verified by CEMS. This control efficiency could be met
through improvements to the primary capture system, construction of a
secondary capture system, and application of the MACT QQQ standards to
the capture systems. For SO2 emissions from the electric
furnace, we propose as BART the work practice standard to prohibit
active aeration. We previously approved Arizona's determination that
BART for PM10 at the Miami Smelter is the NESHAP for Primary
Copper Smelting. We now propose to find that the federally enforceable
provisions of the NESHAP, which apply to the Miami Smelter and are
incorporated into its Title V Permit, are sufficient to ensure the
enforceability of this determination.
Table 1--Proposed Emission Limits on BART Sources
--------------------------------------------------------------------------------------------------------------------------------------------------------
Corresponding control
Source Units Pollutants Limit Measure technology
--------------------------------------------------------------------------------------------------------------------------------------------------------
Sundt Generating Station............ Unit 4................. NOX.................... 0.36 lb/MMBtu.............. Selective Non-Catalytic
SO2.................... 0.23 Reduction.
PM10................... 0.030 Dry Sorbent Injection.
Fabric filter baghouse
(existing).
Unit 4 (Alternative)... NOX.................... 0.25 lb/MMBtu.............. Switch to natural gas.
SO2.................... 0.00064
PM10................... 0.010
Chemical Lime Nelson................ Kiln 1................. NOX.................... 3.80 lb/ton feed........... Selective Non-Catalytic
SO2.................... 9.32 Reduction.
PM10................... 0.12 Lower sulfur fuel.
Fabric filter baghouse
(existing).
Kiln 2................. NOX.................... 2.61 ...................... Selective Non-Catalytic
SO2.................... 9.73 Reduction.
PM10................... 0.12 Lower sulfur fuel.
Fabric filter baghouse
(existing).
Hayden Smelter...................... Converters 1, 3-5...... NOX.................... 40 tpy................... None.
SO2.................... 99.8 Control efficiency.... New double contact acid
plant.
Anode Furnaces 1, 2.... SO2.................... None None.................. Work practice standard.
Miami Smelter....................... Converters 2-5......... NOX.................... 40 tpy................... None.
SO2.................... 99.7 Control efficiency.... Improve primary and new
secondary capture systems.
Electric Furnace....... SO2.................... None None.................. Work practice standard.
--------------------------------------------------------------------------------------------------------------------------------------------------------
2. Proposed RP Determinations
Point Sources of NOX: EPA conducted an extensive RP analysis of
NOX point sources that resulted in proposed determinations
for nine sources and proposed controls on two sources as shown in Table
2. We are proposing an emissions limit of 2.12 lb/ton on Kiln 4 of the
Phoenix Cement Clarkdale Plant based on a 30-day rolling average, which
is consistent with SNCR as a control technology. We are proposing an
emissions limit of 2.67 lb/ton on Kiln 4 of the CalPortland Cement
Rillito Plant based on a 30-day rolling average, which also is
consistent with SNCR control technology. We are also taking comment on
the possibility of requiring a rolling 12-month cap on NOX
emissions in lieu of a lb/ton emission limit. For Phoenix Cement, this
cap would be 947 tpy and apply to Kiln 4. For CalPortland, this cap
would be 2,082 tpy and apply to Kilns 1-4.
Table 2--Proposed Emission Limits on RP Sources
--------------------------------------------------------------------------------------------------------------------------------------------------------
Source Units Pollutants Limit Measure Corresponding control technology
--------------------------------------------------------------------------------------------------------------------------------------------------------
Phoenix Cement................. Kiln 4............ NOX............... 2.12 lb/ton............ Selective Non-Catalytic Reduction.
CalPortland Cement............. Kiln 4............ NOX............... 2.67 lb/ton............ Selective Non-Catalytic Reduction.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Area Sources of NOX and SO2: We propose to find that it is
reasonable not to require additional controls on these sources at this
time. Primarily, these area source categories are distillate fuel oil
combustion in industrial and commercial boilers and in internal
combustion engines, and residential natural gas combustion. The State's
area sources, which currently contribute a relatively small percentage
of the visibility impairment at impacted Class I areas, would benefit
from better emission inventories and an improved RP analysis in the
next planning period.
Reasonable Progress Goals: EPA is proposing RPGs consistent with a
combination of control measures that include those in the approved
Arizona RH SIP as well as the approved and proposed Arizona RH FIP.
While not quantifying a new set of RPGs based on these control
measures, we propose that it is reasonable to assume improved levels of
visibility at Arizona's 12 Class I areas by 2018 since the measures in
the FIP are significantly beyond what was in the State's plan.
Demonstration of Reasonable Progress: EPA proposes to find that it
is not reasonable to provide for rates of progress at the 12 Class I
areas consistent with the uniform rate of progress (URP) in this
planning period.\3\ Given the variety and location of sources
contributing to visibility impairment in Arizona, EPA considers
[[Page 9322]]
it unlikely that Arizona's Class I areas will meet the URP in 2018. We
propose to find that the RP analyses underlying our actions on the
Arizona SIP \4\ and in this proposal are sufficient to demonstrate that
it is not reasonable to provide for rates of progress in this planning
period that would attain natural conditions by 2064.\5\ This is
consistent with our proposed and final rules on the Arizona RH SIP in
which we approved Arizona's determinations that it is not reasonable to
require additional controls to address organic carbon, elemental
carbon, coarse mass and fine soil during this planning period.\6\ We
also approved the State's decision not to require additional controls
(i.e., controls beyond what the State or we determine to be BART) on
point sources of SO2.\7\
---------------------------------------------------------------------------
\3\ 40 CFR 51.308(d)(1)(ii).
\4\ See proposed actions at 77 FR 75727-75730, 78 FR 29297-
292300 and final action at 78 FR 46172.
\5\ 40 CFR 51.308(d)(1)(ii).
\6\ See 77 FR 75728 for a discussion on sources of organic
carbon and elemental carbon (fires), and 78 FR 29297-29299 for a
discussion of coarse mass and fine soil.
\7\ 78 FR 46172.
---------------------------------------------------------------------------
3. Long-Term Strategy Proposal
EPA proposes to find that provisions in today's proposal in
combination with provisions in the approved Arizona SIP and FIP \8\
fulfill the requirements of 40 CFR 51.308(d)(3)(ii), (v)(C) and (v)(F).
These requirements are to include in the LTS measures needed to achieve
emission reductions for out-of-state Class I areas, emissions
limitations and schedules for compliance to achieve the reasonable
progress goals, and enforceability of emissions limitations and control
measures.\9\ In today's notice we propose to promulgate emission
limits, compliance schedules and other requirements for four BART
sources and two RP sources to complete the actions taken in our
previous final rule to address these requirements.
---------------------------------------------------------------------------
\8\ 77 FR 75512-72580, December 5, 2012.
\9\ See 78 FR 46173 (codified at 40 CFR 52.145(e)(ii)).
---------------------------------------------------------------------------
C. Interstate Transport of Pollutants That Affect Visibility
We propose that a combination of SIP and FIP measures will satisfy
the FIP obligation for the visibility requirement of CAA section
110(a)(2)(D)(i)(II) for the 1997 8-hour ozone, 1997 PM2.5,
and 2006 PM2.5 NAAQS. CAA section 110(a)(2)(D)(i)(II)
requires that all SIPs contain adequate provisions to prohibit
emissions that will interfere with other states' required measures to
protect visibility. We refer to this requirement herein as the
interstate transport visibility requirement. ADEQ submitted SIP
revisions to address this requirement in 2007 for the 1997 8-hour ozone
NAAQS \10\ and 1997 PM2.5 NAAQS \11\ (2007 Transport SIP)
\12\ and in 2009 for the 2006 PM2.5 NAAQS \13\ (2009
Transport SIP).\14\ Each of these SIP revisions indicated that it is
appropriate to assess Arizona's interference with other states'
measures to protect visibility in conjunction with the State's RH
SIP.\15\ In our final rule published on July 30, 2013, EPA disapproved
these SIP submittals with respect to the interstate transport
visibility requirement, triggering the obligation for EPA to promulgate
a FIP to address this requirement.\16\ Accordingly, today's notice
describes our proposed FIP for the interstate transport visibility
requirement for the 1997 8-hour ozone, 1997 PM2.5, and 2006
PM2.5 NAAQS.
---------------------------------------------------------------------------
\10\ 62 FR 38856, July 18, 1997.
\11\ 62 FR 38652, July 18, 1997.
\12\ ``Revision to the Arizona State Implementation Plan Under
Clean Air Act Section 110(a)(2)(D)(i)--Regional Transport,''
submitted by ADEQ on May 24, 2007.
\13\ 71 FR 61144, October 17, 2006.
\14\ ``Arizona State Implementation Plan Revision under Clean
Air Act Section 110(a)(1) and (2); 2006 PM2.5 NAAQS, 1997
PM2.5 NAAQS, and 1997 8-hour Ozone NAAQS,'' submitted by
ADEQ on October 14, 2009, which addressed the requirements of
section 110(a)(2)(D)(i) with respect to the 2006 PM2.5
NAAQS in Section 2.4 and Appendix B of the submittal.
\15\ This concept is also presented in EPA's 2006 guidance memo
on interstate transport, which recommended that states make a
submission indicating that it was premature, at that time, to
determine whether there would be any interference with other states'
required measures to protect visibility until the submission and
approval of regional haze SIPs. See ``Guidance for State
Implementation Plan (SIP) Submissions to Meet Current Outstanding
Obligations Under Section 110(a)(2)(D)(i) for the [1997] 8-Hour
Ozone and PM2.5 National Ambient Air Quality Standards,''
August 15, 2006.
\16\ 78 FR 46142, July 30, 2013.
---------------------------------------------------------------------------
III. Review of State and EPA Actions on Regional Haze
A. EPA's Schedule To Act on Arizona's RH SIP
EPA received a notice of intent to sue in January 2011 stating that
we had not met the statutory deadline for promulgating RH FIPs and/or
approving RH SIPs for dozens of states, including Arizona. This notice
was followed by a lawsuit filed by several advocacy groups (Plaintiffs)
in August 2011.\17\ In order to resolve this lawsuit and avoid
litigation, EPA entered into a Consent Decree with the Plaintiffs,
which sets deadlines for action for all of the states covered by the
lawsuit, including Arizona. This decree was entered and later amended
by the United States District Court for the District of Columbia over
the opposition of Arizona.\18\ Under the terms of the Consent Decree,
as amended, EPA is currently subject to three sets of deadlines for
taking action on Arizona's RH SIP as listed in Table 3.\19\
---------------------------------------------------------------------------
\17\ National Parks Conservation Association v. Jackson (D.D.C.
Case 1:11-cv-01548).
\18\ National Parks Conservation Association v. Jackson (D.D.C.
Case 1:11-cv-01548), Memorandum Order and Opinion (May 25, 2012),
Minute Order (July 2, 2012), Minute Order (November 13, 2012) and
Minute Order (February 15, 2013).
\19\ Id.
Table 3--Consent Decree Deadlines for EPA To Act on Arizona's RH SIP
----------------------------------------------------------------------------------------------------------------
EPA actions Proposed rule Final rule
----------------------------------------------------------------------------------------------------------------
Phase 1--BART determinations for July 2, 2012 \1\................... November 15, 2012.\2\
Apache, Cholla and Coronado.
Phase 2--All remaining elements of the December 8, 2012 \3\............... July 15, 2013.\4\
Arizona RH SIP.
Phase 3--FIP for disapproved elements January 27, 2014................... June 27, 2014.
of the Arizona RH SIP.
----------------------------------------------------------------------------------------------------------------
\1\ Published in the Federal Register on July 20, 2012, 77 FR 42834.
\2\ Published in the Federal Register on December 5, 2012, 77 FR 72512.
\3\ Published in the Federal Register on December 21, 2012, 77 FR 75704.
\4\ Published in the Federal Register on July 30, 2013, 78 FR 46142.
B. History of State Submittals and EPA Actions
Because four of Arizona's 12 mandatory Class I Federal areas are on
the Colorado Plateau, the State had the option of submitting a RH SIP
under CAA section 309 of the RHR. A SIP that is approved by EPA as
meeting all of the requirements of section 309 is ``deemed to comply
with the requirements for reasonable progress with respect to the 16
Class I areas [on the Colorado
[[Page 9323]]
Plateau] for the period from approval of the plan through 2018.'' \20\
When these regulations were first promulgated, 309 SIPs were due no
later than December 31, 2003. Accordingly, ADEQ submitted to EPA on
December 23, 2003, a 309 SIP for Arizona's four Class I Areas on the
Colorado Plateau. ADEQ submitted a revision to its 309 SIP, consisting
of rules on emissions trading and smoke management, and a correction to
the State's regional haze statutes, on December 31, 2004. EPA approved
the smoke management rules submitted as part of the revisions in
2004,\21\ but did not propose or take final action on any other portion
of the 309 SIP.
---------------------------------------------------------------------------
\20\ 40 CFR 51.309(a).
\21\ 71 FR 28270 and 72 FR 25973.
---------------------------------------------------------------------------
In response to a court decision,\22\ EPA revised 40 CFR 51.309 on
October 13, 2006, making a number of substantive changes and requiring
states to submit revised 309 SIPs by December 17, 2007.\23\
Subsequently, ADEQ sent a letter to EPA dated December 24, 2008,
acknowledging that it had not submitted a SIP revision to address the
requirements of 40 CFR 51.309(d)(4) related to stationary sources and
40 CFR 51.309(g), which governs reasonable progress requirements for
Arizona's eight mandatory Class I areas outside of the Colorado
Plateau.\24\
---------------------------------------------------------------------------
\22\ Center for Energy and Economic Development v. EPA, 398 F.3d
653 (D.C. Circuit 2005).
\23\ 71 FR 60612.
\24\ Letter from Stephen A. Owens, ADEQ, to Wayne Nastri, EPA,
dated December 24, 2008.
---------------------------------------------------------------------------
EPA made a finding on January 15, 2009, that 37 states, including
Arizona, had failed to make all or part of the required SIP submissions
to address regional haze.\25\ Specifically, EPA found that Arizona
failed to submit the plan elements required by 40 CFR 51.309(d)(4) and
(g). EPA sent a letter to ADEQ on January 14, 2009, notifying the State
of this failure to submit a complete SIP. ADEQ decided to submit a SIP
under CAA section 308, instead of under section 309. EPA proposed on
February 5, 2013,\26\ to disapprove Arizona's 309 SIP except for the
smoke management rules that we had previously approved. Our final rule
partially disapproving Arizona's 309 SIP was published on August 8,
2013.\27\
---------------------------------------------------------------------------
\25\ 74 FR 2392.
\26\ 78 FR 8083.
\27\ 78 FR 48326.
---------------------------------------------------------------------------
ADEQ adopted and transmitted its 2011 RH SIP under section 308 of
the RHR to EPA Region 9 in a letter dated February 28, 2011. The SIP
was determined complete by operation of law on August 28, 2011.\28\ The
SIP was properly noticed by the State and available for public comment
for 30 days prior to one public hearing held in Phoenix, Arizona, on
December 2, 2010. Arizona included in its SIP responses to written
comments from EPA Region 9, the National Park Service, the U.S. Forest
Service, and other stakeholders including regulated industries and
environmental organizations. The 2011 RH SIP is available to review in
the docket for this proposed rule.\29\
---------------------------------------------------------------------------
\28\ CAA section 110(k)(1)(B).
\29\ ``Arizona State Implementation Plan, Regional Haze under
Section 308 of the Federal Regional Haze Rule,'' February 28, 2011.
---------------------------------------------------------------------------
As shown in Table 3, the first phase of EPA's action on the 2011 RH
SIP addressed three BART sources. The final rule for the first phase (a
partial approval and partial disapproval of the State's plan and a
partial FIP) was signed by the Administrator on November 15, 2012, and
published in the Federal Register on December 5, 2012. The emission
limits on the three sources will improve visibility by reducing
NOX emissions by about 22,700 tons per year. In the second
phase of our action, we proposed on December 21, 2012, to approve in
part and disapprove in part the remainder of the 2011 RH SIP. ADEQ
submitted an Arizona RH SIP Supplement on May 3, 2013, to correct
certain deficiencies identified in that proposal. We then proposed on
May 20, 2013, to approve in part and disapprove in part the Supplement.
Our final rule approving in part and disapproving in part Arizona's RH
SIP was published on July 30, 2013.
C. EPA's Authority To Promulgate a FIP
Under CAA section 110(c), EPA is required to promulgate a FIP
within 2 years of the effective date of a finding that a state has
failed to make a required SIP submission. The FIP requirement is
terminated if a state submits a regional haze SIP, and EPA approves
that SIP before promulgating a FIP. See 74 FR 2392. Specifically, CAA
section 110(c) provides:
(1) The Administrator shall promulgate a Federal implementation
plan at any time within 2 years after the Administrator--
(A) finds that a State has failed to make a required submission
or finds that the plan or plan revision submitted by the State does
not satisfy the minimum criteria established under [CAA section
110(k)(1)(A)], or
(B) disapproves a State implementation plan submission in whole
or in part, unless the State corrects the deficiency, and the
Administrator approves the plan or plan revision, before the
Administrator promulgates such Federal implementation plan.
Section 302(y) defines the term ``Federal implementation plan'' in
pertinent part, as:
[A] plan (or portion thereof) promulgated by the Administrator
to fill all or a portion of a gap or otherwise correct all or a
portion of an inadequacy in a State implementation plan, and which
includes enforceable emission limitations or other control measures,
means or techniques (including economic incentives, such as
marketable permits or auctions or emissions allowances) . . .
Thus, because we determined that Arizona failed to timely submit a
Regional Haze SIP, we are required to promulgate a Regional Haze FIP
for Arizona, unless we first approve a SIP that corrects the non-
submittal deficiencies identified in our finding of January 15, 2009.
For the reasons explained below, we approved in part and disapproved in
part the Arizona Regional Haze SIP on July 30, 2013. Therefore, we are
proposing a FIP to address those portions of the SIP that we
disapproved.
IV. EPA's BART Process
A. BART Factors
The purpose of the BART analysis is to identify and evaluate the
best system of continuous emission reduction based on the BART
Guidelines \30\ as summarized below. Steps 1 through 3 address the
availability, feasibility and effectiveness of retrofit control
options. In our analysis of control technology options, we expressly
include the emission baseline calculation that is a key factor in
determining control effectiveness. Step 4 is the five-factor BART
analysis that results in selecting the emission limit that represents
BART in Step 5. Following the process steps is a short description of
each BART factor.
---------------------------------------------------------------------------
\30\ See July 6, 2005 BART Guidelines, 40 CFR 51, Regional Haze
Regulations and Guidelines for Best Available Retrofit Technology
Determinations.
---------------------------------------------------------------------------
Step 1--Identify all available retrofit control technologies.
Step 2--Eliminate technically infeasible options.
Step 3--Evaluate control effectiveness of remaining control
technologies.
Step 4--Evaluate impacts and document the results.
Factor 1: Cost of compliance.
Factor 2: Energy and non-air quality environmental impacts
of compliance.
Factor 3: Pollution control equipment in use at the
source.
Factor 4: Remaining useful life of the facility.
Factor 5: Visibility impacts.
Step 5--Select BART.
Factor 1: Costs of Compliance: The evaluation of costs is an
important part of a five-factor analysis because it influences the
cost-effectiveness that is
[[Page 9324]]
compared to the visibility benefits. Estimating the cost of compliance
primarily depends on the cost estimates and control effectiveness of
each technically feasible BART control option. For each of the four
BART facilities evaluated in this section, we state the source of the
cost-related information and how it was used in our analysis. While EPA
relies primarily on the cost methods in our Control Cost Manual, we
also rely on verified cost estimates from the companies and cost
methods used for specific industries. In some cases, certain capital
costs and annual operating costs were developed by our contractor based
on actual costs associated with specific types of sources. Where
possible, we have conducted new cost analyses considering more recent
information from ADEQ or from the four BART facilities. Please refer to
the TSD for the detailed cost analyses.
Factor 2: Energy and Non-air Quality Environmental Impacts: In
assessing the potential energy impacts of BART control options, we
consider direct and indirect effects on energy availability and costs.
An example of a direct energy impact is the cost of energy consumption
from the control equipment. Examples of non-air quality impacts include
safety issues associated with handling and transportation of anhydrous
ammonia or the ability to sell fly ash rather than dispose of it.
Factor 3: Pollution Equipment in Use at the Source: The presence of
existing pollution control technology at each source is reflected in
our BART analysis in two ways. First, we always consider simple
retention of existing equipment as a BART candidate. We also consider
existing equipment in determining available control technologies that
can be used with or replace such equipment. Second, where appropriate,
we consider existing equipment in developing baseline emission rates
for use in cost calculations and visibility modeling. Pollutant-
specific discussions of these issues are included in the following
sections.
Factor 4: Remaining Useful Life of the Source: We consider each
source's ``remaining useful life'' as one element of the overall cost
analysis as allowed by the BART Guidelines.\31\ In cases where we are
not aware of any enforceable shut-down date for a particular source or
unit, we use a 20-year amortization period as the remaining useful life
per the EPA Cost Control Manual.
---------------------------------------------------------------------------
\31\ 40 CFR Part 51, Appendix Y, section IV.D.4.k.
---------------------------------------------------------------------------
Factor 5: Anticipated Degree of Visibility Improvement: EPA relied
on the CALPUFF modeling system (version 5.8) for visibility modeling,
which consists of the CALPUFF dispersion model, the CALMET
meteorological data processor, and the CALPOST post-processing program.
The initial modeling was performed by our contractor, the University of
North Carolina (UNC) at Chapel Hill. In some cases, companies submitted
BART analyses including visibility modeling that we used to evaluate
visibility benefits. An explanation of the visibility analysis and
tables follows this section, a description of the modeling is included
in the five-factor discussion for each source, and more details are
available in the TSD.
B. Visibility Analysis
EPA estimated the degree of visibility improvement expected to
result from various BART control options based on the difference
between baseline visibility impacts prior to controls and visibility
impacts with controls in operation. Baseline emissions were based on
the highest 24-hour emissions from monitored emissions data when
available, otherwise from estimates of production rates and emission
factors. Control case emissions were derived from the baseline by
applying the percent reduction in emission factor expected from the
control. Impacts at all Class I areas within 300 km of each facility
were assessed. EPA used the CALPUFF model version 5.8 \32\ to determine
the baseline and post-control visibility impacts, following the
modeling approach recommended in the BART Guidelines. Our contractor at
UNC developed a modeling protocol and carried out most of the modeling
and the post-processing of model output into tables of visibility
impacts. EPA supplemented this for certain sources with modeling of
additional control scenarios, corrections to some scenarios and post-
processing work, and some sensitivity simulations. Also, EPA performed
the modeling for the two smelters. Details of the modeling are in the
TSD.
---------------------------------------------------------------------------
\32\ EPA relied on version 5.8 of CALPUFF because it is the EPA-
approved version promulgated in the Guideline on Air Quality Models
(40 CFR part 51, Appendix W, section 6.2.1.e; 68 FR 18440, April 15,
2003). EPA updated the specific version to be used for regulatory
purposes on June 29, 2007, including minor revisions as of that
date; the approved CALPUFF modeling system includes CALPUFF version
5.8, level 070623, and CALMET version 5.8 level 070623. At this
time, any other version of the CALPUFF modeling system would be
considered an ``alternative model'', subject to the provisions of
Guideline on Air Quality Models section 3.2.2(b), requiring a full
theoretical and performance evaluation.
---------------------------------------------------------------------------
EPA modeled all units (stacks) and pollutants simultaneously for
each source. Modeling of all emissions from all units accounts for the
chemical interaction between multiple plumes, and between plumes and
background concentrations. This also accounts for the fact that
deciview benefits from controls on individual units are not strictly
additive. As recommended in the BART Guidelines, the 98th percentile
daily impact in deciviews is used as the basic metric of visibility
impact. EPA relied on the 98th percentile over the merged 2001-2003
period. The alternative of using the average of the three 98th
percentiles from 2001, 2002 and 2003 was also calculated, and the
results of using it are provided in the TSD, although they differ
little from the merged approach. Both are valid indicators of the 98th
percentile.\33\ EPA also mainly relied on the revised IMPROVE equation
for translating pollutant concentrations into deciviews (CALPOST
visibility method 8), the recommended method for new visibility
analyses. The old IMPROVE equation (method 6) was used by most states
in their original SIP submittals and was acceptable at that time. EPA
used the best 20 percent of natural background days in calculating
delta deciviews. For the original SIP submittals, states were free to
use this or the annual average background. Overall, we refer to the
method we used as method ``8b'' (``b'' for ``best''). Model results
using visibility method 6 and annual average background conditions
(``a'' for average) also are provided in the TSD (i.e., methods 6a, 6b,
and 8a, as well as 8b).
---------------------------------------------------------------------------
\33\ For each modeled day, the CALPUFF model provides the
highest impact from among the receptor locations for a given Class I
area. The baseline impact in the tables is the 98th percentile among
these daily values. The improvement in the tables is the difference
between that baseline impact and the 98th percentile impact after
applying controls. The 98th percentile is represented by the 22nd
high over the 2001-2003 period modeled. The TSD includes an
alternative, the average of each of the three years' 8th highs,
which yields slightly different values.
---------------------------------------------------------------------------
C. Explanation of Visibility Tables
For each facility, this notice provides one or more tables of
visibility impacts and visibility improvement from controls in
deciviews. Each table has the same format: columns list the Class I
areas within 300 km of the facility, the distance,\34\ baseline modeled
visibility impact from the facility for each area, and one or more
columns with the
[[Page 9325]]
modeled visibility improvement from a candidate control option. A
modeling run abbreviation, such as ``base'' or ``ctrl2'', is included
along with a short description of the option. For several facilities,
there are two different baselines incorporating different emission
assumptions. For these, there are baseline and control columns for each
of the two baselines. For Sundt Unit 4, there are separate tables for
SO2 and NOX controls, and an additional table
showing the effect of reductions for both SO2 and
NOX for the proposed BART controls and for a better-than-
BART alternative. At the bottom of each table are five rows showing
impacts and improvements from the facility for all the Class I areas
considered together, and also two measures of visibility cost-
effectiveness. The cost-effectiveness here is ``dollars per deciview,''
where dollars is the annualized total cost of the control in millions
of dollars per year, divided by either the sum of deciview improvements
over all impacted Class I areas, or the largest single area deciview
improvement. Cost-effectiveness in terms of dollars per ton is
presented in other tables and has been considered for each source and
BART option. The headings for these table rows are:
---------------------------------------------------------------------------
\34\ The distances given are from the facility to the nearest
model receptor location; distances to the actual Class I area
boundary may be slightly less. Receptor locations are defined for
all Class I areas by the National Park Service. See ``Class I
Receptors'' Web site, http://www2.nature.nps.gov/air/maps/Receptors/
.
---------------------------------------------------------------------------
(1) ``Cumulative (sum),'' the cumulative impact or improvement that
is computed as the sum of impact or improvement over all the areas;
(2) ``Maximum,'' single largest impact or improvement that is the
maximum over all the areas;
(3) `` CIAs >= 0.5 dv,'' the number of Class I areas
having a baseline impact from the source of at least 0.5 dv (or, for
the control columns, the number of areas showing improvement of at
least 0.5 dv due to the control);
(4) ``Million $/dv (cumul. dv),'' annual control cost in millions
of dollars per deciview considering the improvement at all the Class I
areas together; and
(5) ``Million $/dv (max. dv),'' annualized cost per deciview
considering the largest single area improvement.
The Federal Land Managers have sometimes used $10 million/dv as a
comparison benchmark for the $/dv computed from the maximum, and $20
million/dv as a benchmark for $/dv computed from cumulative deciviews.
We have not endorsed the use of these or any other $/dv benchmarks as
criteria for making BART determinations.
The TSD for this notice provides bar charts and additional
visibility tables, including results for individual modeled years and
their average, the old IMPROVE equation, and annual average background
conditions instead of best 20 percent. There also are model results for
various sensitivity analyses.
V. EPA's Proposed BART FIP
A. Sundt Generating Station Unit 4
Summary: EPA is proposing to find that Sundt Unit 4 is eligible for
and subject to BART. EPA is proposing BART emissions limits on Sundt
Generating Station Unit 4 for NOX, SO2 and
PM10 based on the corresponding control technologies listed
in Table 4 and described in the following BART analyses. For
NOX, we propose an emission limit of 0.36 lb/MMBtu
consistent with the use of SNCR. For SO2, we propose an
emission limit of 0.23 lb/MMBtu consistent with the use of DSI. For
PM10, we propose a filterable PM10 emission limit
of 0.03 lb/MMBtu based on the use of the existing fabric filter
baghouse. Finally, we are also proposing a switch to natural gas as a
better-than-BART alternative.
Table 4--Sundt 4: Summary of Proposed BART Determinations
----------------------------------------------------------------------------------------------------------------
Emission limit (lb/
Pollutant MMBtu) Control technology
----------------------------------------------------------------------------------------------------------------
NOX.............................. 0.36 Selective Non-Catalytic Reduction.
SO2.............................. 0.23 Dry Sorbent Injection.
PM10............................. 0.030 Fabric filter baghouse (existing).
----------------------------------------------------------------------------------------------------------------
Affected Class I Areas: Ten Class I areas are within 300 km of
Sundt. Their nearest borders range from 17 km to 247 km away, with
Saguaro NP the closest, and Galiuro WA the second closest. The highest
baseline visibility impact of Sundt Unit 4 is 3.4 dv at Saguaro. The
second highest baseline impact is 1.1 dv at Galiuro. Other areas have
visibility impacts of 0.5 dv or less. The cumulative sum of visibility
impacts over all the Class I areas is 6.6 dv.
Facility Overview: The Sundt Generating Station is an electric
utility power plant located in Tucson, Arizona, operated by Tucson
Electric Power. The plant consists of four steam electric boilers and
three stationary combustion turbines for a total net generating
capacity of approximately 500 megawatts (MW).\35\ Sundt Unit 4 is a
steam electric boiler that was manufactured in 1964 and placed into
operation in about 1967. Unit 4 is a dry bottom wall-fired boiler with
a maximum gross capacity of 130 MW when firing coal. Originally
designed to fire natural gas and fuel oil, Sundt Unit 4 was converted
to also be able to fire coal in the early 1980s as a result of an order
issued by the Department of Energy. The unit now fires both coal and
natural gas, as explained in more detail below. As part of the coal
conversion, the unit was equipped with a fabric filter for particulate
matter control. Unit 4 was upgraded in 1999 with LNB and overfire air
(OFA) designed to meet Phase II Acid Rain Program requirements. At
present, Unit 4 operates with the pollution control equipment and is
subject to the emission limits listed in Table 5 that reflects a coal-
operating scenario.
---------------------------------------------------------------------------
\35\ As described in Pima DEQ Permit No. 1052, in the TSD.
[[Page 9326]]
Table 5--Sundt 4: Current Emission Limits and Control Technology
----------------------------------------------------------------------------------------------------------------
Pollutant Emission limit Control device
----------------------------------------------------------------------------------------------------------------
NOX............................. 0.46 lb/MMBtu \36\. LNB with OFA.
SO2............................. 1 lb/MMBtu \37\.... None.
PM10............................ 233 lb/hr \38\..... Fabric filter/baghouse.
----------------------------------------------------------------------------------------------------------------
TEP has indicated that the generating capacity of Sundt Unit 4
while firing coal is reduced compared to its capacity using natural
gas. As reported to the Energy Information Agency (EIA), Unit 4 has a
173 MW nameplate capacity while firing natural gas. However, the
maximum gross capacity at which the unit could operate for a sustained
period of time while burning coal is about 130 MW. This is due
primarily to the fact that the amount of coal that can be introduced to
the boiler is limited by the size of the boiler. Excess coal injection
causes the flame to impinge on the back wall of the boiler which
damages the boiler tubes.\39\ A summary of historical emissions data
for a recent period of time is in Table 6.
---------------------------------------------------------------------------
\36\ Pima DEQ Permit No. 1052, Attachment F: Phase II Acid Rain
Permit.
\37\ Pima DEQ Permit No. 1052, Specific Condition II.A.2.b.
\38\ As determined by Pima DEQ Permit No. 1052, Specific
Condition II.A.1.
\39\ TEP's letter dated May 10, 2013, page 2.
Table 6--Sundt 4: Historical Emissions (2008-2012)
--------------------------------------------------------------------------------------------------------------------------------------------------------
NOX SO2
Year Heat duty ---------------------------------------------------- Coal (tons) Natural gas
(MMBtu/yr) (tpy) (lb/MMBtu) (tpy) (lb/MMBtu) (MCF)
--------------------------------------------------------------------------------------------------------------------------------------------------------
2012......................................................... 6,313,719 945 0.297 371 0.118 44,049 4,660,701
2011......................................................... 5,993,769 1,366 0.445 2,185 0.729 265,111 157,919
2010......................................................... 6,869,999 1,303 0.368 1,733 0.505 162,212 1,904,433
2009......................................................... 4,801,971 709 0.285 636 0.265 73,464 2,642,992
2008......................................................... 8,709,923 1,880 0.429 2,882 0.661 378,956 18,422
--------------------------------------------------------------------------------------------------------------------------------------------------------
Baseline Emissions Calculations: The baseline period, baseline
emissions, and capacity factor are three key variables in determining
BART that are linked to fuel usage. TEP has indicated that while Sundt
Unit 4 predominantly has operated as a coal-fired unit, it has recently
expanded its use of natural gas as a result of historically low natural
gas prices.\40\ As shown in the last column of Table 6, Unit 4 has used
much higher amounts of natural gas during 2009-2010 and again in 2012
that are not representative of anticipatable operations based on coal.
Accordingly, we use calendar year 2011 emissions when Unit 4
predominately used coal as the baseline period for annual average
emission estimates. Although this represents only a single year of
emissions data, we consider this period of coal usage, rather than a
period of primarily natural gas usage, to represent a realistic
depiction of anticipated annual emissions when burning coal.\41\ In
addition, we rely on an annual capacity factor of 0.49 based on a coal-
fired capacity of 130 MW and actual generation from the baseline period
of 2011. For visibility modeling, we used baseline emissions for
NOX and SO2 based on maximum daily emission
rates, as reported to EPA's CAMD Acid Rain Program database, for the
period from 2008 to 2010. While this time period is prior to the 2011
baseline period used for the annual emission estimates, the highest
daily emission rates from 2008 to 2010 correspond to coal usage. Since
these maximum daily emission rates still correspond to coal usage, we
consider them reasonable estimates of baseline emissions despite the
fact that they are drawn from a baseline period different from the one
used to estimate annual emission rates. For PM10, the
baseline emission rate used in visibility modeling is based on the
value in the original Western Regional Air Partnership (WRAP)
visibility modeling that reflects the use of coal and the existing
fabric filter. For a more detailed analysis of how we determined the
baseline period, baseline emissions and capacity factor, please refer
to the TSD.
---------------------------------------------------------------------------
\40\ TEP's letter dated May 10, 2013, page 2.
\41\ As discussed in the BART Guidelines, 40 CFR Part 51,
Appendix Y, section IV.D.4.d.
---------------------------------------------------------------------------
Modeling Overview: EPA's contactor UNC performed the initial
modeling of Sundt's visibility impacts. EPA performed supplemental
modeling to correct some minor errors in the initial work and to
estimate impacts from additional control scenarios, such as switching
entirely to natural gas fuel. EPA also modeled the impacts for the
western unit of Saguaro NP, whereas originally only the eastern unit
was included. Although only Unit 4 is BART-eligible, all four Sundt
units were included in the CALPUFF modeling to more accurately
represent the chemistry of the facility's pollutant plume. Baseline
emissions for modeling were based on daily CAMD emissions monitoring
data for 2008-2010, a period with no changes in pollution controls at
the facility. Control case emissions were derived from the baseline by
applying the percent reduction expected from the control.
Saguaro NP has an eastern unit, the Rincon Mountain District, and a
western unit, the Tucson Mountain District. In the original set of
modeling receptor locations developed by the National Park Service,
only the eastern unit was included. CALPUFF modeling typically covered
only the eastern unit. This is true of modeling by the WRAP, and also
of modeling by EPA's contractor UNC, which used the WRAP work as a
starting point. A more recent set of NPS modeling receptors from 2008
is available that covers both eastern and western units of Saguaro. For
this FIP, EPA remodeled for both Saguaro units where needed for a given
facility. The only facilities for which it makes a significant
difference are TEP Sundt and CalPortland Cement due to their close
proximity to Saguaro.
[[Page 9327]]
1. Proposed Eligible and Subject to BART
EPA is proposing to find that Sundt Unit 4 is eligible for and
subject to BART. In our final rulemaking on the Arizona RH SIP dated
July 30, 2013, we disapproved ADEQ's finding that Sundt Unit 4 was not
eligible for BART.\42\ In particular, we found that, although this unit
was ``reconstructed'' in 1987, it remains BART-eligible because it did
not undergo prevention of significant deterioration (PSD) review at the
time of reconstruction.\43\ For this reason, we propose to find Sundt
Unit 4 is eligible for a BART analysis of the three haze-causing
pollutants: NOX, SO2 and PM10.
---------------------------------------------------------------------------
\42\ 78 FR 46175 (codified at 40 CFR 52.145(e)(2)(i)).
\43\ See 78 FR 75722, 78 FR 46151, and ``TEP Sundt Unit I4 BART
Eligibility Memo'' (November 21, 2012).
---------------------------------------------------------------------------
Under the RHR and the BART Guidelines, any BART-eligible source
that either ``causes'' or ``contributes'' to visibility impairment at
any Class I area is subject to BART.\44\ EPA previously approved ADEQ's
decision to set 0.5 dv as the threshold for determining whether a
source contributes to visibility impairment at a given Class I
area.\45\ In order to determine whether Sundt Unit 4 is subject to
BART, EPA's contractor UNC evaluated whether Unit 4 has an impact of
0.5 dv or more at any Class I area. UNC's visibility modeling showed
that two Class I areas experienced a 98th percentile impact greater
than 0.5 dv due to emissions from Sundt Unit 4.\46\ In particular, the
98th percentile impact across the three years modeled was 2.798 dv at
Saguaro and 0.839 dv at Galiuro.\47\ These results indicate that Sundt
Unit 4 causes visibility impairment at Saguaro and contributes to
impairment at Galiuro. Therefore, EPA proposes to find that Sundt Unit
4 is subject to BART.
---------------------------------------------------------------------------
\44\ 40 CFR part 51, appendix Y, section III.A.
\45\ 77 FR 46152-53.
\46\ Technical Analysis for Arizona and Hawaii Regional Haze
FIPs: Report on Identification of Sources Subject to BART, UNC, July
20, 2012, Table 4.
\47\ For an expanded discussion of our approach to visibility
modeling, please refer to Section III (General Approach to the Five-
Factor BART analysis) of the Sundt4 TSD. This approach was used in
both determining whether Sundt 4 was subject to BART, as well as in
evaluating the visibility factor in the BART analysis.
---------------------------------------------------------------------------
2. Proposed BART Analysis and Determination for NOX
For our NOX BART analysis, we identify all available
control technologies, eliminate options that are not technically
feasible, and evaluate the control effectiveness of the remaining
control options. We then evaluate each technically feasible control in
terms of a five-factor BART analysis and propose a determination for
BART.
a. Control Technology Availability, Technical Feasibility, and
Effectiveness
EPA proposes to find that SNCR and selective catalytic reduction
(SCR) are available and technically feasible options to control
NOX emissions with a control efficiency of approximately 50
percent for SNCR and approximately 89 percent for SCR.
SNCR involves the non-catalytic decomposition of NOX to
molecular nitrogen and water. Typical NOX control
efficiencies for SNCR range from 40 to 60 percent, depending on inlet
NOX concentrations, fluctuating flue gas temperatures,
residence time, amount and type of nitrogenous reducing agent, mixing
effectiveness, acceptable levels of ammonia slip, and presence of
interfering chemical substances in the gas stream. Because Sundt Unit 4
already operates with NOX combustion controls, we have used
an SNCR control efficiency of 30 percent from a baseline that includes
LNB with OFA. Considering typical combustion control technologies such
as LNB and OFA can achieve control efficiencies of about 25 to 30
percent, the result is total control efficiency from an uncontrolled
baseline of about 50 percent, which is in the mid-range of SNCR control
efficiencies.
SCR is a post-combustion gas treatment technique that uses either
ammonia or urea in the presence of a metal-based catalyst to
selectively reduce NOX to molecular nitrogen, water, and
oxygen. The catalyst lowers the temperature required for the chemical
reaction between NOX and the reducing agent. Technical
factors that impact the effectiveness of this technology include the
catalyst reactor design, operating temperature, type of fuel fired,
sulfur content of the fuel, design of the ammonia injection system, and
the potential for catalyst poisoning. SCR has been installed on
numerous coal-fired boilers of varying sizes, and is considered
technically feasible. We note that SCRs are classified as a low dust
SCR (LDSCR) or high dust SCR (HDSCR). As explained in the TSD, the SCR
system considered in this analysis is the HDSCR.
Existing vendor literature and technical studies indicate that SCR
systems are capable of achieving approximately 80 to 90 percent control
efficiency, and that this emission rate can be achieved on a retrofit
basis, particularly when combined with combustion control technology
such as LNB.\48\ Our contractor used a design emission rate of 0.050
lb/MMBtu (annual average), which in the case of Sundt Unit 4
corresponds to a control efficiency of 89 percent. While this is a
value close to the upper range of SCR control efficiency, we consider
the use of 0.050 lb/MMBtu appropriate for Sundt Unit 4. A review of
Acid Rain Program data indicates that there are up to seven dry-bottom,
wall-fired boilers operating with SCR on a retrofit basis that have
achieved an annual average emission rate of 0.050 lb/MMBtu or lower in
practice.\49\ However, there are design differences between Sundt Unit
4 and these other units (i.e., boiler size, coal type and
characteristics, and loading profile) that have the potential to affect
this comparison. If we receive additional comments that sufficiently
document source-specific considerations justifying the use of an
emission rate higher than 0.050 lb/MMBtu, we may incorporate such
considerations in our selection of BART.
---------------------------------------------------------------------------
\48\ See ``Emissions Control: Cost-Effective Layered Technology
for Ultra-Low NOx Control'' (2007), ``What's New in SCRs'' (2006),
and ``Nitrogen Oxides Emission Control Options for Coal-Fired
Electric Utility Boilers'' (2005).
\49\ See spreadsheet ``CAMD Wall-fired Coal EGUs.xlsx'' in the
docket.
---------------------------------------------------------------------------
b. BART Analysis for NOX
Costs of Compliance: In evaluating the costs of compliance for SNCR
and SCR, we calculated the control costs ($) and emission reductions
(tons/year of pollutant) for each control technology, and developed
average cost-effectiveness ($/ton) values. Estimated NOX
emission reductions are summarized in Table 7 and cost-effectiveness
numbers are summarized in Table 8 for each option. A more detailed
version of emission calculations are in our docket \50\ and in our
contractor's report. The heat duty and capacity factor used in the
emission calculations below differ from the values used in the
calculations originally prepared by our contractor, due to the unit's
lower capacity when burning coal (130 MW) rather than natural gas (173
MW). The heat duty (MMBtu/hr) and capacity factor (0.49) reflect the
coal-burning heat duty, rather than the natural gas-burning heat
duty.\51\
---------------------------------------------------------------------------
\50\ See spreadsheet ``Sundt4 2001-12 Emission Calcs 2014-01-
24.xlsx'' in the docket.
\51\ As noted by TEP in its May 10, 2013 letter, although the
calculated capacity factor is different, the annual emissions in
tons per year removed do not change significantly, as the change in
capacity factor is largely offset by the change in maximum unit
gross rating.
[[Page 9328]]
Table 7--Sundt 4: NOX Control Option Emission Estimates
--------------------------------------------------------------------------------------------------------------------------------------------------------
Control Emission Heat duty Capacity NOX emission rate NOX
efficiency factor ------------- factor -------------------------- emission
Control option -------------------------- ------------- reduction
MMBtu/hr lb/hr tpy ------------
% lb/MMBtu % tpy
--------------------------------------------------------------------------------------------------------------------------------------------------------
Baseline (LNB+OFA)........................................... ........... 0.445 1,371 0.49 610 1,310
SNCR+LNB+OFA................................................. 30 0.312 1,371 0.49 427 917 393
SCR+LNB+OFA.................................................. 89 0.050 1,371 0.49 69 147 1,162
--------------------------------------------------------------------------------------------------------------------------------------------------------
Our consideration of the cost of compliance focuses primarily on
the cost-effectiveness of each control option as measured in average
cost per ton and incremental cost per ton of each control option as
shown in Table 8. SCR is the most stringent option with the highest
average cost-effectiveness of $5,176/ton, and incremental cost-
effectiveness over SNCR of $6,174/ton. Detailed cost calculations can
be found in our docket.\52\ While we have relied primarily upon the
cost calculations prepared by our contractor, we have incorporated
certain elements of TEP's analysis \53\ into our cost calculations. The
most significant revisions to cost estimates include the following:
---------------------------------------------------------------------------
\52\ See spreadsheet ``Sundt4 Control Costs 2014-01-26.xlsx'' in
the docket.
\53\ Letter dated May 10, 2013.
---------------------------------------------------------------------------
We have changed the unit size from 173 MW to 130 MW to
reflect the gross capacity of using coal. Although this has the net
effect of decreasing certain costs, particularly several operation and
maintenance (O&M) costs, the revised capital cost estimates increased
for SCR (from $38 million to $45 million) and SNCR (from $2.8 million
to $3.1 million).
We have used a retrofit difficulty value of 1.5 (increased
from 1.0) in cost estimates due to certain difficulties associated with
retrofit installation of SCR. These difficulties are the result of site
congestion and the configuration of the existing boiler structure and
coal handling system as noted by TEP.
We have included the cost of air preheater modifications
that TEP stated are necessary in order to accommodate SCR due to site
congestion and coal handling configuration.
Table 8--Sundt 4: NOX Control Option Cost-Effectiveness
--------------------------------------------------------------------------------------------------------------------------------------------------------
Capital Annualized Annual Total Emission Cost-effectiveness ($/
cost capital operating annual cost reduction ton)
Control option ------------- cost cost ---------------------------------------------------
--------------------------
($) ($) ($) ($/yr) (tpy) Ave Incremental
--------------------------------------------------------------------------------------------------------------------------------------------------------
SNCR......................................................... $3,079,089 $290,644 $975,124 $1,265,768 393 $3,222
SCR.......................................................... 45,167,561 4,263,498 1,753,975 6,017,474 1,162 5,176 $6,174
--------------------------------------------------------------------------------------------------------------------------------------------------------
Pollution Control Equipment in Use at the Source: The presence of
existing pollution control technology at Sundt Unit 4 is reflected in
the consideration of available control technologies and in the
development of baseline emission rates for use in cost calculations and
visibility modeling. In the case of NOX, current pollution
controls are reflected in our selection of 2011 as the baseline period,
which includes the use of LNB and OFA.
Energy and Non-Air Quality Environmental Impacts: Regarding
potential energy impacts of the BART control options, we note that SCR
incurs a draft loss that will result in certain load loss, and that
other emissions controls may also have modest energy impacts. The costs
for direct energy impacts, i.e., power consumption from the control
equipment and additional draft system fans from each control
technology, are included in the cost analyses. Indirect energy impacts,
such as the energy to produce raw materials, are not considered, which
is consistent with the BART Guidelines. Ammonia adsorption (resulting
from ammonia injection from SCR or SNCR) to fly ash is generally not
desirable due to odor but does not impact the integrity of the use of
fly ash in concrete. The ability to sell fly ash is unlikely to be
affected by the installation of SNCR or SCR technologies. Finally, SNCR
and SCR may involve potential safety hazards associated with the
transportation and handling of anhydrous ammonia. However, since the
handling of anhydrous ammonia will involve the development of a risk
management plan (RMP), we consider the associated safety issues to be
manageable as long as established safety procedures are followed. As a
result, we do not consider these impacts sufficient to warrant the
elimination of either of the available control technologies.
Remaining Useful Life of the Source: We are considering the
``remaining useful life'' of Sundt Unit 4 as one element of the overall
cost analysis as allowed by the BART Guidelines.\54\ Since there is not
state- or federally-enforceable shut-down date for this unit, we have
used a 20-year amortization period per the EPA Cost Control Manual as
the remaining useful life for the facility.\55\
---------------------------------------------------------------------------
\54\ 40 CFR Part 51, Appendix Y, section IV.D.4.k.
\55\ We note that the 20 year amortization period is primarily
used in NOX control cost calculations, such as for SCR.
In order to promote consistency in the analysis, we have used the 20
year period in the cost calculations for other control options, such
as for SO2 control, for which the Control Cost Manual
includes examples that use an amortization period of 15 years.
---------------------------------------------------------------------------
Degree of Visibility Improvement: The visibility improvement due to
NOX controls is modest. SNCR was modeled at a 30 percent
NOX emission reduction. As shown in Table 9, this yields a
maximum visibility improvement of just over 0.2 dv at Saguaro. Galiuro
improves about half as much, and other areas much less. The cumulative
improvement across all impacted Class I areas is 0.5 dv. SCR was
modeled at 89 percent NOX reduction to achieve 0.05 lb/
MMBtu. SCR provides a maximum improvement of 0.8 dv, which occurs at
Saguaro. Galiuro again improves about half as much, and the cumulative
improvement across all Class I areas is 1.6 dv. This visibility
improvement is substantially greater for SCR than for SNCR.
[[Page 9329]]
Table 9--Sundt 4: Visibility Impact and Improvement From NOX Controls
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
Distance impact ---------------------------
Class I area (km) -------------- SNCR
Base case (ctrl04) SCR (ctrl08)
----------------------------------------------------------------------------------------------------------------
Chiricahua NM............................................ 144 0.43 0.03 0.12
Chiricahua WA............................................ 141 0.51 0.05 0.15
Galiuro WA............................................... 64 1.10 0.12 0.34
Gila WA.................................................. 232 0.17 0.02 0.04
Mazatzal WA.............................................. 203 0.19 0.02 0.04
Mount Baldy WA........................................... 232 0.15 0.01 0.03
Pine Mountain WA......................................... 247 0.15 0.02 0.03
Saguaro NP............................................... 17 3.40 0.23 0.78
Sierra Ancha WA.......................................... 178 0.19 0.01 0.04
Superstition WA.......................................... 137 0.32 0.01 0.05
Cumulative (sum)......................................... ........... 6.6 0.5 1.6
Maximum.................................................. ........... 3.40 0.23 0.78
CIAs >= 0.5 dv................................. ........... 3 0 1
Million $/dv (cumul. dv)................................. ........... ............ $2.4 $3.7
Million $/dv (max. dv)................................... ........... ............ $5.5 $7.7
----------------------------------------------------------------------------------------------------------------
c. Proposed BART Determination for NOX
EPA proposes to find that BART for NOX is an emission
limit of 0.36 lb/MMBtu on a 30-day BOD rolling basis that is achievable
by SNCR with LNB and OFA. The primary factors supporting this proposed
finding are the average cost-effectiveness and anticipated visibility
benefits of controls. In particular, while SCR is anticipated to
achieve the greatest degree of visibility improvement, it is also
significantly more expensive than SNCR, with an average cost-
effectiveness of $5176/ton. We do not consider this average cost to be
warranted by the projected visibility benefit of SCR for this facility.
Table 10 provides a summary of our five-factor BART analysis.
In proposing an emission limit of 0.36 lb/MMBtu, we have considered
the annual average design value for SNCR of 0.31 lb/MMBtu as well as
the need to account for emissions associated with startup and shutdown
events. To account for this variability, we have examined the
difference between the highest 30-day rolling NOX value and
the highest annual average NOX value observed over the
baseline period, which is approximately 17 percent.\56\ We have applied
this variability to the annual average design value to develop a 30-day
BOD rolling emission limit, which we consider to provide sufficient
margin for a limit that will apply at all times.
---------------------------------------------------------------------------
\56\ See spreadsheet ``Sundt4 2001-12 Emission Calcs 2014-01-
24.xlsx'' in the docket.
---------------------------------------------------------------------------
We propose to require compliance with this requirement within three
years of the effective date of the final rule. A 2006 Institute of
Clean Air Companies (ICAC) study indicated that the installation time
for a typical SNCR retrofit, from bid to startup, is 10 to 13
months.\57\ However, because we are also requiring the installation of
additional SO2 controls, we consider a three year period for
compliance with both BART determinations to be appropriate. We are
seeking comment on whether this compliance date is reasonable and
consistent with the requirement of the Clean Air Act that BART be
installed ``as expeditiously as practicable but in no event later than
five years after [promulgation of the applicable FIP].'' \58\ If we
receive information during the comment period that establishes that a
different compliance time frame is appropriate, we may finalize a
different compliance date. Finally, we are proposing regulatory text
that includes monitoring, reporting, and recordkeeping requirements to
ensure that the emission limit and compliance deadline are enforceable.
As part of the proposed monitoring requirements, we are including a
requirement to monitor rates of ammonia injection in order to ensure
proper operation of the SNCR in a manner that minimizes ammonia
emissions.
---------------------------------------------------------------------------
\57\ See ``Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources'', Institute of
Clean Air Companies, December 4, 2006.
\58\ Clean Air Act section 169A(g)(4), 42 U.S.C. 7491(g)(4).
Table 10--Sundt 4: Summary of BART Analysis for NOX
----------------------------------------------------------------------------------------------------------------
LNB+OFA
Sundt unit 4 (130 MW) (baseline) SNCR+LNB SCR+LNB
----------------------------------------------------------------------------------------------------------------
Emissions
----------------------------------------------------------------------------------------------------------------
Emission Factor (lb/MMBtu)................... 0.445 0.312.................... 0.050
Emission Rate (tpy).......................... 1310 917...................... 147
Emission Reduction (tpy)..................... ........... 393...................... 1,162
Control Effectiveness (%).................... ........... 30%...................... 89%
----------------------------------------------------------------------------------------------------------------
Costs of Compliance
----------------------------------------------------------------------------------------------------------------
Capital Cost ($)............................. ........... $3,079,089............... $45,167,561
Annualized Capital Cost ($).................. ........... $290,644................. $4,263,498
Annual O&M ($)............................... ........... $975,124................. $1,753,975
[[Page 9330]]
Total Annual Cost ($)........................ ........... $1,265,768............... $6,017,474
Ave Cost-Effectiveness ($/ton)............... ........... $3,222................... $5,176
Incremental Cost-Effectiveness ($/ton)....... ........... ......................... $6,174
----------------------------------------------------------------------------------------------------------------
Pollution Control Equipment in Use
----------------------------------------------------------------------------------------------------------------
Low-NOX Burners and Over Fire Air
----------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts
----------------------------------------------------------------------------------------------------------------
Energy impacts have been reflected in annual O&M costs in the costs of compliance.
----------------------------------------------------------------------------------------------------------------
SCR and SNCR may create potential safety and environmental hazards from the transportation and handling of
anhydrous ammonia. We consider these impacts manageable with the development of an RMP and additional safety
procedures, and do not consider them sufficient enough to warrant eliminating either of these available control
technologies.
----------------------------------------------------------------------------------------------------------------
Remaining Useful Life
----------------------------------------------------------------------------------------------------------------
Control technology amortization period....... ........... 20 years................. 20 years
----------------------------------------------------------------------------------------------------------------
Visibility Improvement
----------------------------------------------------------------------------------------------------------------
Single largest Class I area improvement (dv). ........... 0.23..................... 0.78
Single Class I area cost-effectiveness ........... $5.5..................... $7.7
(million $/dv).
Class I areas with >= 0.50 dv improvement.... ........... 0........................ 1
Cumulative visibility improvement (dv)....... ........... 0.5...................... 1.6
Cumulative cost-effectiveness (million $/dv). ........... $2.4..................... $3.7
----------------------------------------------------------------------------------------------------------------
4. Proposed BART Analysis and Determination for SO2
For our SO2 BART analysis, we identified all available
control technologies, eliminated options that are not technically
feasible, and evaluated the control effectiveness of the remaining
control options. We then evaluated each control in terms of a five-
factor BART analysis and proposed a determination for BART.
a. Control Technology Availability, Technical Feasibility, and
Effectiveness
EPA identified three available and technically feasible
technologies to control SO2 emissions from Sundt Unit 4.
These technologies are lime or limestone-based wet flue gas
desulfurization (wet FGD), lime spray dry absorber (SDA or dry FGD),
and dry sorbent injection (DSI). While each of these control options
has certain design concerns and constraints associated with their
implementation, all three options are considered technically feasible.
Lime or limestone-based wet FGD: Wet scrubbing systems mix an
alkaline reagent, such as hydrated lime or limestone, with water to
generate scrubbing slurry that is used to remove SO2 from
the flue gas. The alkaline slurry is sprayed countercurrent to the flue
gas, such as in a spray tower, or the flue gas may be bubbled through
the alkaline slurry as in a jet bubbling reactor. As the alkaline
slurry contacts the exhaust stream, it reacts with the SO2
in the flue gas. Design variations may include changes to increase the
alkalinity of the scrubber slurry, increase slurry/SO2
contact, and minimize scaling and equipment problems. Insoluble calcium
sulfite (CaSO3) and calcium sulfate (CaSO4) salts
are formed in the chemical reaction that occurs in the scrubber, and
exit as part of the scrubber slurry. The salts are eventually removed
and handled as a solid waste byproduct. The waste byproduct is mainly
CaSO3, which is difficult to dewater. Solid waste byproducts
from wet lime scrubbing are typically managed in dewatering ponds and
landfills.
Design concerns associated with wet FGD involve the substantial
water usage requirements needed to generate the alkaline reagent slurry
as well as the substantial amount of wastewater and solid waste
discharge associated with the spent byproduct. A wet FGD control system
must be located after the fabric filter baghouse because the moist
plume resulting from the wet scrubber system would create baghouse
plugging issues if the control is placed ahead of the baghouse. In
addition, a substantial footprint is required for the management of
these waste products as well as for the absorber tower and associated
process equipment such as the slurry preparation, mixing, associated
tanks, and dewatering activities. While these design concerns do
present some challenges, they do not warrant elimination of this option
as technically infeasible.\59\
---------------------------------------------------------------------------
\59\ TEP's review does not eliminate consideration of wet FGD,
but does describe several design challenges that TEP notes should be
reflected in the five factor analysis. We have incorporated certain
elements of TEP's review in our analysis, as discussed in Step 4.
---------------------------------------------------------------------------
Our contractor has estimated that newly constructed wet FGD systems
could achieve design emission rates (annual average basis) of 0.06 lb/
MMBtu. Relative to baseline SO2 emission rates, this
corresponds to a control efficiency of 92 percent. We recognize that
FGD systems are designed to achieve more stringent emission rates, and
have demonstrated an ability to achieve control efficiencies up to 98
percent. Our contractor's report notes that the lower control
efficiency cited here is regarded as a conservative estimate. While
this is not the most stringent level of control that the technology is
capable of achieving, we consider 92 percent control efficiency to be
consistent with the median values reported for wet FGD systems.
Lime SDA or dry FGD: A spray dryer absorber uses a stream of either
dry lime or hydrated lime (semi-dry) in a reaction tower where it
reacts with SO2 in the flue gas to form calcium sulfite
solids. Unlike wet FGD systems that produce a slurry by-product that is
collected
[[Page 9331]]
separately from the fly ash, dry FGD systems are designed to produce a
dry byproduct that must be removed with the fly ash in the particulate
control equipment. As a result, dry FGD systems must be located
upstream of the particulate control device to remove the reaction
products and excess reactant material. In instances where hydrated lime
is used as a reagent, the reaction towers must be designed to provide
adequate contact and residence time between the exhaust gas and the
slurry to produce a relatively dry byproduct. Typical process equipment
associated with a spray dryer typically includes an alkaline storage
tank, mixing and feed tanks, an atomizer, spray chamber, particulate
control device and a recycle system. The recycle system collects solid
reaction products and recycles them back to the spray dryer feed system
to reduce alkaline sorbent use.
A design concern associated with a dry FGD system is that it must
be installed prior to the fabric filter baghouse in order for the
reagent to be captured and recycled. As noted in our contractor's
report, the location of the existing fabric filter baghouse does not
present enough space to install a new absorber between the boiler and
the existing baghouse. As a result, a dry FGD at Sundt Unit 4 is
assumed to include a new baghouse, which is reflected in the costs of
compliance for the five-factor analysis. We consider this control
option to be technically feasible.
Our contractor has estimated that newly constructed dry FGD systems
could achieve design emission rate (annual average basis) of 0.08 lb/
MMBtu. Relative to baseline SO2 emission rates, this
corresponds to a control efficiency of 89 percent. As noted for wet FGD
systems, this is a conservative estimate of what dry FGD systems can
achieve, and is consistent with the median values reported for dry FGD
systems.
Dry Sorbent Injection: DSI involves the injection of powdered
absorbent directly into the flue gas exhaust stream. These are simple
systems that generally require a sorbent storage tank, feeding
mechanism, transfer line and blower, and an injection device. The dry
sorbent is typically injected countercurrent to the gas flow. An
expansion chamber is often located downstream of the injection point to
increase residence time and efficiency. Particulates generated in the
reaction are controlled in the system's particulate control device. DSI
requires less capital equipment, less physical space, and less
modification to existing ductwork compared to a dry FGD system.
However, reagent costs are much higher and, depending upon the
absorbent and amount of sorbent injected, control efficiency is lower
when compared to a dry FGD system. Soda ash and Trona (sodium
sesquicarbonate) are potential options for reagent use. An important
design consideration of DSI is the ability of the downstream
particulate control device to accommodate the additional particulate
loading resulting from the addition of the DSI reagent into the boiler
flue gas. More effective particulate control devices allow for higher
rates of sorbent injection, which in turn allow for more effective
SO2 control.
In a review of SO2 control options for BART eligible
units, the Northeast States for Coordinated Air Use Management
(NESCAUM) estimated control effectiveness for DSI in a range of 40-60
percent.\60\ More recently, as part of work done as part of the
Integrated Planning Model (IPM), EPA has estimated control
effectiveness as high as 80 percent,\61\ depending upon factors such as
the type of sorbent, the quantity of sorbent used, and the type of
particulate control device employed. Generally, the use of more
effective particulate control devices allow for higher rates of sorbent
injection, and therefore greater DSI effectiveness. Since Sundt Unit 4
operates with a fabric filter, we consider a control effectiveness
value in the upper range appropriate, and have used 70 percent control
effectiveness in our calculations. This value is above the range
indicated in the NESCAUM study, but does not require the high sorbent
injection rates required to achieve the upper range of control
indicated in IPM documentation. A summary of the control technologies
and their associated control effectiveness is presented in Table 11.
---------------------------------------------------------------------------
\60\ ``Assessment of Control Technology Options for BART-
Eligible Sources'', Northeast States for Coordinated Air Use
Management In Partnership with The Mid-Atlantic/Northeast Visibility
Union, March 2005.
\61\ IPM Model--Revisions to Cost and Performance for APC
Technologies, Dry Sorbent Injection Cost Development Methodology,
August 2010.
Table 11--Sundt 4: SO2 Control Options
------------------------------------------------------------------------
Control
Control option effectiveness
%
------------------------------------------------------------------------
Dry Sorbent Injection................................... 70
Dry FGD or Lime SDA..................................... 89
Wet FGD (lime- or limestone-based)...................... 92
------------------------------------------------------------------------
b. BART Analysis for SO2
Costs of Compliance: Our consideration of the costs of compliance
focuses primarily on the cost-effectiveness of each control option, as
measured in cost per ton and incremental cost per ton. The emissions
estimates and cost-effectiveness for the three control options are
shown in Table 12 and Table 13, respectively. Both wet and dry FGD have
average cost-effectiveness values over $5,000/ton, much greater than
DSI, which is a control option that we consider very cost-effective at
$1,857/ton. Moreover, both wet and dry FGD have very high incremental
cost-effectiveness values, indicating that while they are more
effective than less stringent control options, this additional degree
of effectiveness comes at a substantial cost.
In evaluating the costs of compliance for the control options, we
have calculated the control costs ($) and emission reductions (tons/
year of pollutant) for each control technology, developed average cost-
effectiveness ($/ton) values, and arrived at the emission reductions
for each option as summarized Table 12. A more detailed version of
emission calculations is in our docket,\62\ and in our contractor's
report. As noted previously in our NOX BART analysis, the
heat duty and capacity factor used in these calculations differ from
the values used in the calculations originally prepared by our
contractor because the maximum gross capacity of Sundt Unit 4 while
burning coal is about 130 MW, compared to its natural-gas nameplate
capacity of 173 MW. The heat duty (MMBtu/hr) and capacity factor used
in Table 12 reflect the coal-burning nameplate capacity.\63\ Detailed
cost calculations presented in Table 13 are in the docket.\64\
---------------------------------------------------------------------------
\62\ See spreadsheet ``Sundt4 2001-12 Emission Calcs 2014-01-
24.xlsx'' in the docket.
\63\ As noted by TEP and Burns and McDonnell, although the
calculated capacity factor is different, the annual emissions in
tons per year removed do not change significantly, as the change in
capacity factor is largely offset by the change in maximum unit
gross rating.
\64\ See spreadsheet ``Sundt4 Control Costs 2014-01-26.xlsx'' in
the docket.
[[Page 9332]]
Table 12--Sundt 4: SO2 Control Option Emission Estimates
--------------------------------------------------------------------------------------------------------------------------------------------------------
Control Emission Heat duty SO2 emission rate SO2
efficiency factor ------------- -------------------------- emission
Control option -------------------------- Capacity reduction
(MMBtu/hr) factor (lb/hr) (tpy) ------------
(%) (lb/MMBtu) (tpy)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Baseline (no control)........................................ ........... 0.729 1,371 0.49 1,000 2,145
DSI.......................................................... 70 0.219 1,371 0.49 300 644 1,502
DFGD......................................................... 89 0.080 1,371 0.49 110 236 1,909
WFGD......................................................... 92 0.060 1,371 0.49 82 177 1,969
--------------------------------------------------------------------------------------------------------------------------------------------------------
Table 13--Sundt 4: SO2 Control Option Cost-Effectiveness
--------------------------------------------------------------------------------------------------------------------------------------------------------
Capital Annualized Annual Total Emission Cost-effectiveness ($/
cost capital operating annual cost reduction ton)
Control option ------------- cost cost ---------------------------------------------------
--------------------------
($) ($) ($) ($/yr) (tpy) Ave Incremental
--------------------------------------------------------------------------------------------------------------------------------------------------------
DSI.......................................................... $3,250,000 $306,777 $2,482,107 $2,788,884 1,502 $1,857
DFGD......................................................... 72,470,559 6,840,708 2,880,841 9,721,549 1,909 5,091 $17,007
WFGD......................................................... 80,629,663 7,610,870 3,227,467 10,838,337 1,969 5,505 18,795
--------------------------------------------------------------------------------------------------------------------------------------------------------
Pollution Control Equipment in use at Source: In the case of
SO2, Sundt Unit 4 does not operate with any existing control
technology. This is reflected in our selection of calendar year 2011 as
the baseline period, which represents uncontrolled coal-fired
emissions.
Energy and Non-Air Quality Environmental Impacts: For wet FGD,
energy impacts include certain auxiliary power requirements that are
necessary to operate the wet FGD system and to potentially compensate
for pressure head loss through the scrubber. These energy impacts are
reflected as auxiliary power costs in the cost of compliance estimates.
Non-air quality environmental impacts include water usage requirements
and the storage and disposal of wet ash. Wet FGD requires very large
quantities of water to ensure proper control effectiveness. Securing
such quantities of water is a significant challenge in more arid
regions of the country such as Arizona, and would preclude the use of
that water for potentially more beneficial uses. The on-site storage
and disposal of wet ash in large retention ponds triggers significant
additional regulatory requirements, as it represents a substantial
water pollution threat.
For dry FGD, the energy and non-air environmental impacts are
similar to those for wet FGD. Operation of a dry FGD system still
requires securing significant supplies of water, although to a lesser
degree than wet FGD systems. In addition, dry FGD systems will result
in generation of larger quantities of boiler ash, and has the potential
to affect negatively the properties and quality of boiler ash. In some
instances, boiler ash that is suitable to sell for beneficial purposes
may no longer be marketable following installation of a dry FGD system.
Energy impacts also include auxiliary power requirements for operation
of the dry FGD system, and for overcoming pressure head loss through
the scrubber. While we note certain potential impacts resulting from
the water resource requirements associated with wet FGD as well as the
additional solid waste generation associated with wet and dry FGD, we
do not consider these impacts sufficient enough to warrant eliminating
these control technologies.
DSI could potentially have an adverse effect on the quality of the
boiler fly ash, which would make it unmarketable for beneficial uses.
Use of DSI also results in an ash byproduct which would require
landfill disposal, thereby increasing solid waste generation rates at
the plant. Energy impacts are limited to auxiliary power requirements
for operation of the DSI system. We do not consider these impacts
sufficient enough to warrant eliminating this control technology.
Remaining Useful Life of the Source: We are considering the
remaining useful life of Sundt Unit 4 as one element of the overall
cost analysis as allowed by the BART Guidelines. Since we are not aware
of any federally- or State-enforceable shut down date for Sundt Unit 4,
we have used a 20-year amortization period described in the EPA Cost
Control Manual as the remaining useful life for the control options
considered for Unit 4. We note that the remaining useful life of the
source is reflected in the evaluation of cost of compliance through the
use of a 20-year amortization period in control cost calculations.
Degree of Visibility Improvement: The visibility improvement due to
SO2 controls is modest. As shown in Table 14, control via
DSI, with a 70 percent SO2 emissions reduction, gives a
maximum visibility improvement of 0.2 dv, which occurs at Saguaro.
Three other areas improve about half as much, and the cumulative
improvement is 0.8 dv. Emissions controls via dry and wet FGD were
modeled at 89 percent and 92 percent SO2 emissions
reduction, respectively. Both dry and wet FGD would cause a visibility
disbenefit at Saguaro as indicated by the negative improvements in
Table 14. The disbenefit is mainly due to the decreased stack exit
temperature and exit velocity associated with these technologies, and
more so for wet FGD than for dry FGD. These stack decreases result in
less plume rise and increased impacts nearby. At areas farther away,
the disbenefit is outweighed by the benefit of SO2
reductions from FGD. This issue is discussed further in the TSD. With
FGD, the maximum benefit occurs not at Saguaro, but at Galiuro, with
0.2 dv for dry FGD and 0.1 dv for wet FGD. The corresponding cumulative
improvements are 0.6 dv and 0.4 dv for dry and wet FGD, respectively,
including the areas of disbenefit. All these improvements are
substantially lower than those from DSI, and the visibility cost-
effectiveness of each FGD is more than quadruple that of DSI. EPA finds
that the improvement from DSI is substantial enough to support its
selection as BART, and that it is clearly a better choice than dry FGD
and wet FGD.
[[Page 9333]]
Table 14--Sundt 4: Visibility Impact and Improvement From SO2 Controls
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
Distance impact --------------------------------------
Class I Area (km) ------------------ DSI 70% Dry FGD Wet FGD
Base case (ctrl14) (ctrl02) (ctrl03)
----------------------------------------------------------------------------------------------------------------
Chiricahua NM............................. 144 0.43 0.05 0.07 0.06
Chiricahua Wild........................... 141 0.51 0.10 0.10 0.11
Galiuro Wild.............................. 64 1.10 0.10 0.16 0.09
Gila Wild................................. 232 0.17 0.04 0.05 0.05
Mazatzal Wild............................. 203 0.19 0.07 0.08 0.09
Mount Baldy Wild.......................... 232 0.15 0.05 0.05 0.06
Pine Mountain Wild........................ 247 0.15 0.05 0.06 0.06
Saguaro NP................................ 17 3.40 0.20 -0.16 -0.27
Sierra Ancha Wild......................... 178 0.19 0.06 0.08 0.08
Superstition Wild......................... 137 0.32 0.09 0.10 0.10
Cumulative (sum).......................... ........... 6.6 0.8 0.6 0.4
Maximum................................... ........... 3.40 0.20 0.16 0.11
CIAs >= 0.5 dv.................. ........... 3 0 0 0
Million $/dv (cumul. dv).................. ........... ................ $3.5 $16.4 $25.1
Million $/dv (max. dv).................... ........... ................ $14 $60 $97
----------------------------------------------------------------------------------------------------------------
c. BART Determination for SO2
EPA proposes an emission limit of 0.23 lb/MMBtu on a 30-day (BOD)
rolling basis as BART to control SO2 from Sundt Unit 4. This
emission limit, equivalent to using DSI, is considered very cost-
effective at $1,857/ton. In evaluating the appropriate emission limit
for DSI, we have considered the annual average design value for DSI of
0.21 lb/MMBtu as well as the need to account for emissions associated
with startup and shutdown events. To determine how to account for this
variability, we have examined the difference between the highest 30-day
rolling SO2 value and the highest annual average
SO2 value observed over the baseline period, which is
approximately 9 percent.\65\ We have applied this variability to the
annual average design value to develop a 30-day BOD rolling emission
limit, which we consider a sufficient margin for a limit that will
apply at all times. Please refer to Table 15 that provides a summary of
our five-factor BART analysis.
---------------------------------------------------------------------------
\65\ See spreadsheet ``Sundt4 2001-12 Emission Calcs 2014-01-
24.xlsx'' in the docket.
---------------------------------------------------------------------------
We propose to require compliance with this requirement within three
years of the effective date of the final rule. However, we are seeking
comment on whether this compliance date is reasonable and consistent
with the requirement of the Clean Air Act that BART be installed ``as
expeditiously as practicable but in no event later than five years
after [promulgation of the applicable FIP].'' \66\ If we receive
information during the comment period that establishes that a different
compliance time frame is appropriate, we may finalize a different
compliance date. We are also proposing regulatory text that includes
monitoring, reporting, and recordkeeping requirements associated with
this emission limit.
---------------------------------------------------------------------------
\66\ Clean Air Act section 169A(g)(4), 42 U.S.C. 7491(g)(4).
Table 15--Sundt 4: Summary of BART Analysis for SO2
----------------------------------------------------------------------------------------------------------------
Sundt Unit 4 (130 MW) Baseline DSI Dry FGD Wet FGD
----------------------------------------------------------------------------------------------------------------
Emission Factor (lb/MMBtu).... 0.729 0.219................ 0.08................. 0.06
Emission Rate (tpy)........... 2145 644.................. 236.................. 177
Emission Reduction (tpy)...... ........... 1,502................ 1,909................ 1,969
Control Effectiveness......... ........... 70%.................. 89%.................. 92%
----------------------------------------------------------------------------------------------------------------
Cost of Compliance
----------------------------------------------------------------------------------------------------------------
Capital Cost ($).............. ........... $3,250,000........... $72,470,559.......... $80,629,663
Annualized Capital Cost ($)... ........... $306,777............. $6,840,708........... $7,610,870
Annual O&M ($)................ ........... $2,482,107........... $2,880,841........... $3,227,467
Total Annual Cost ($)......... ........... $2,788,884........... $9,721,549........... $10,838,337
Ave CE ($/ton)................ ........... $1,857............... $5,091............... $5,505
Incremental CE ($/ton)........ ........... ..................... $23,081.............. $18,795
----------------------------------------------------------------------------------------------------------------
Pollution Control Equipment in Use at Source
----------------------------------------------------------------------------------------------------------------
There is no existing control technology for SO2
----------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts
----------------------------------------------------------------------------------------------------------------
Energy impacts are reflected in annual O&M costs in the costs of compliance.
----------------------------------------------------------------------------------------------------------------
Wet ash from wet and dry FGD represents a substantial water pollution threat.
----------------------------------------------------------------------------------------------------------------
Water resources for wet and dry FGD may preclude more beneficial uses of water.
----------------------------------------------------------------------------------------------------------------
Remaining Useful Life
----------------------------------------------------------------------------------------------------------------
Control technology ........... 20 years............. 20 years............. 20 years
amortization period.
----------------------------------------------------------------------------------------------------------------
[[Page 9334]]
Visibility Improvement
----------------------------------------------------------------------------------------------------------------
Single largest Class I area ........... 0.20................. 0.16................. 0.11
improvement (dv).
Single Class I area cost- ........... $14.3................ $60.4................ $96.8
effectiveness (million $/dv).
Class I areas with >= 0.50 dv ........... 0.................... 0.................... 0
improvement.
Cumulative visibility ........... 0.8.................. 0.6.................. 0.4
improvement (dv).
Cumulative cost-effectiveness ........... $3.5................. $16.4................ $25.1
(million $/dv).
----------------------------------------------------------------------------------------------------------------
3. Proposed BART Analysis and Determination for PM10
a. Control Technology Availability, Technical Feasibility, and
Effectiveness
Sundt Unit 4 currently operates with a fabric filter baghouse for
particulate control, which is considered the most stringent control
device for particulate matter. These devices operate on the same
principle as a vacuum cleaner. Air carrying dust particles is forced
through a cloth bag that is designed and manufactured to trap particles
greater than a certain specified diameter. As the air passes through
the fabric, the dust accumulates on the cloth and is removed from the
air stream. The accumulated dust is periodically removed from the cloth
by shaking or by reversing the air flow. The layer of dust, known as
dust cake, trapped on the surface of the fabric has the potential to
result in high efficiency rates for particles ranging in size from
submicron to several hundred microns in diameter.
b. BART Analysis for PM10
The BART Guidelines provide that, where a source has controls
already in place that are the most stringent controls available, it is
not necessary to complete comprehensively a full five-factor BART
analysis, as long the most stringent controls available are made
federally enforceable. Therefore, instead of completing the remaining
steps of a five-factor BART analysis, we have evaluated the appropriate
level of emissions to ensure that the fabric filter achieves an
appropriate degree of control.
c. Proposed BART Determination for PM10
EPA is proposing a filterable PM10 BART emission limit
of 0.03 lb/MMBtu based on the use of the existing fabric filter
baghouse currently in operation, which is the most stringent control
for particulate matter. We note that Mercury and Air Toxics (MATS) Rule
establishes an emission standard of 0.03 lb/MMBtu filterable PM (as a
surrogate for toxic non-mercury metals) as representing Maximum
Achievable Control Technology (MACT) for coal-fired EGUs.\67\ This
standard derives from the average emission limitation achieved by the
best performing 12 percent of existing coal-fired EGUs, as based upon
test data used in developing the MATS Rule.\68\ The BART Guidelines
provide that, ``unless there are new technologies subsequent to the
MACT standards which would lead to cost-effective increases in the
level of control, you may rely on the MACT standards for purposes of
BART.'' \69\ Therefore, we propose to find that 0.03 lb/MMBtu
filterable PM10 is an appropriate limit for BART at Sundt
Unit 4.
---------------------------------------------------------------------------
\67\ 77 FR 9304, 9450, 9458 (February 16, 2012) (codified at 40
CFR 60.42Da(a), 60.50Da(b)(1)).
\68\ See Memorandum from Jeffrey Cole (RTI International) to
Bill Maxwell (EPA) regarding ``National Emission Standards for
Hazardous Air Pollutants (NESHAP) Maximum Achievable Control
Technology (MACT) Floor Analysis for Coal- and Oil-fired Electric
Utility Steam Generating Units for Final Rule'' (December 16, 2011).
\69\ 40 CFR Part 51, Appendix Y, Section IV.C.
---------------------------------------------------------------------------
4. Better Than BART Alternative
We are proposing a switch to natural gas on Sundt Unit 4 as a
better-than-BART alternative to the emissions controls previously
proposed in this section for a coal-fired unit. Unit 4 was originally
constructed as a natural gas-fired boiler, and has used natural gas as
a primary fuel for significant periods of time since 2009. While a
change in fuel supply to natural gas instead of coal is an inherently
less polluting option, the BART Guidelines do not require the
consideration of fuel supply changes as a control option.\70\ As a
result, the option of burning only natural gas is not considered in our
BART analysis. However, TEP has submitted to EPA an alternative to BART
based on the elimination of coal as a fuel source for Sundt Unit 4 by
December 31, 2017. As part of this submittal, TEP compared the
potential emission reductions and visibility benefit between a natural
gas fuel change and certain combinations of NOX and
SO2 controls.\71\
---------------------------------------------------------------------------
\70\ 40 CFR Part 51, Appendix Y, Section IV.D.1.5, ``STEP 1: How
do I identify all available retrofit emission control techniques?''
\71\ Letter dated November 1, 2013.
---------------------------------------------------------------------------
EPA has evaluated this alternative proposal pursuant to the
``better-than-BART'' provisions of the RHR. In particular, the RHR
allows for implementation of ``an emissions trading program or other
alternative measure'' in lieu of BART if the alternative measure
achieves greater reasonable progress than would be achieved through the
installation and operation of BART.\72\ The rule further states that
``[i]f the distribution of emissions is not substantially different
than under BART, and the alternative measure results in greater
emissions reductions, than the alternative measures may be deemed to
achieve greater reasonable progress''.\73\ Because the emissions
reductions under EPA's BART proposal for Sundt Unit 4 and the
reductions from TEP's proposed alternative would occur at the same
facility, the distribution of emissions under BART and the alternative
are not substantially different. Therefore, if the alternative emission
control strategy results in greater emissions reductions than our BART
proposal, EPA may deem the alternative emission control strategy to
achieve greater reasonable progress. A comparison of annual emission
estimates between the BART determination and alternative to BART is
summarized in Table 16. BART determination annual emissions are based
upon the annual average emission factors and annual capacity factor
used in our BART analysis, consistent with coal usage. For the
alternative to BART, annual emissions are based on a combination of
historical natural gas usage data as indicated in TEP's submittal, as
well as standard emission factors for natural gas combustion. A more
detailed discussion of emission estimates from these two scenarios is
included in our TSD.
---------------------------------------------------------------------------
\72\ 40 CFR 51.308(e)(2).
\73\ 40 CFR 51.308(e)(3).
[[Page 9335]]
Table 16--Sundt 4: Comparison of BART Determination and Alternative to BART
----------------------------------------------------------------------------------------------------------------
Natural gas fuel
Parameters Units BART determination switch Difference
----------------------------------------------------------------------------------------------------------------
Heat Duty........................ MMBtu/hr........... 1,371.............. 1,828..............
Capacity Factor.................. ................... 0.49............... 0.37...............
NOX.............................. Ctrl Tech.......... SNCR+LNB+OFA....... LNB+OFA............
lb/MMBtu \1\....... 0.31............... 0.22...............
tpy................ 917................ 652................ 265
Particulate Matter............... Ctrl Tech.......... Fabric Filter...... None...............
lb/MMBtu \1\....... 0.03............... 0.01...............
tpy................ 88................. 30................. 59
SO2.............................. Ctrl Tech.......... Dry Sorbent None...............
Injection.
lb/MMBtu\1\........ 0.22............... 0.00064............
tpy................ 644................ 1.9................ 642
----------------------------------------------------------------------------------------------------------------
\1\ Annual average emission factors.
As seen in Table 16, a change to natural gas usage achieves greater
emission reductions than each of the individual BART determinations for
NOX, SO2, and particulate matter, as well as in
the aggregate. Although visibility modeling is not required to support
a better-than-BART determination in this instance, EPA conducted
modeling to verify the visibility benefits of the proposed alternative,
as compared with EPA's BART determination. This modeling is described
in the TSD and the results are summarized in Table 17.
Table 17--Sundt 4: Visibility Impact and Improvement From Combined SO2 and NOX BART, and From Better-Than-BART
Alternative
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
impact -------------------------
Class I Area Distance ------------- SNCR DSI
(km) 70% Natural gas
Base case (ctrl15) (ctrl13)
----------------------------------------------------------------------------------------------------------------
Chiricahua NM............................................... 144 0.43 0.09 0.19
Chiricahua WA............................................... 141 0.51 0.16 0.25
Galiuro WA.................................................. 64 1.10 0.24 0.47
Gila WA..................................................... 232 0.17 0.06 0.10
Mazatzal WA................................................. 203 0.19 0.08 0.12
Mount Baldy WA.............................................. 232 0.15 0.06 0.09
Pine Mountain WA............................................ 247 0.15 0.06 0.09
Saguaro NP.................................................. 17 3.40 0.49 1.06
Sierra Ancha WA............................................. 178 0.19 0.08 0.12
Superstition WA............................................. 137 0.32 0.11 0.19
Cumulative (sum)............................................ ........... 6.6 1.4 2.7
Maximum..................................................... ........... 3.40 0.49 1.06
CIAs >= 0.5 dv.................................... ........... 3 0 1
Million $/dv (cumul. dv).................................... ........... ........... $2.8 ...........
Million $/dv (max. dv)...................................... ........... ........... $8.3 ...........
----------------------------------------------------------------------------------------------------------------
Since Sundt is only 17 km from the eastern unit of Saguaro, its
emitted NOX may not be fully converted to NO2 by
the time it reaches there, as is assumed in the CALPUFF model. It thus
may not be fully available to form visibility-degrading particulate
nitrate. EPA explored this issue in CALPUFF sensitivity simulations
described in the TSD. For EPA's proposed BART of SNCR plus DSI, the
visibility improvement remains above 0.3 dv even when unrealistically
low 10 percent NO-to-NO2 conversion is assumed (i.e., no
additional conversion of NO to NO2 once the plume leaves the
stack). The improvement from switching to natural gas remains above 0.7
dv at Saguaro. These results show that the FIP's proposed BART
determination remains reasonable despite any concern over the NO
conversion rate; the visibility improvement from BART remains
substantial. The finding that natural gas provides better visibility
improvement than the proposed BART determination also remains sound
regardless of the NO conversion assumed.
Based on this information, we consider a natural gas fuel switch to
result in greater emission reductions and achieve greater reasonable
progress than the proposed BART determinations. Under this scenario, we
are proposing a NOX emission limit of 0.25 lb/MMBtu based on
a 30-day BOD rolling average. As discussed previously in the
NOX BART determination, this represents about a 17 percent
increase from the annual average emission rate of 0.22 lb/MMBtu, which
we consider to provide sufficient margin for a limit that will apply at
all times, including periods of startup and shutdown. In addition, we
are proposing particulate matter and SO2 emission limits
consistent with natural gas use, as well as monitoring, reporting, and
recordkeeping requirements.
B. Chemical Lime Nelson Plant Kilns 1 and 2
Summary: EPA is proposing to find that Chemical Lime Nelson is
subject to BART. EPA is proposing BART emission limits for
NOX, SO2 and PM10 for Kilns 1 and 2 at
the Nelson Plant as listed in Table 18 and described in this section.
[[Page 9336]]
Table 18--Nelson Lime Plant: Summary of Proposed BART Determinations
----------------------------------------------------------------------------------------------------------------
Control technology*
Source Pollutant Emission Limit (lb/ton feed) (for reference only)
----------------------------------------------------------------------------------------------------------------
Kiln 1............................. NOX................... 3.80 Selective Non-
Catalytic Reduction
(SNCR).
SO2................... 9.32 Lower sulfur fuel.
PM10.................. 0.12 Fabric filter
baghouse (existing).
Kiln 2............................. NOX................... 2.61 Selective Non-
Catalytic Reduction
(SNCR).
SO2................... 9.73 Lower sulfur fuel.
PM10.................. 0.12 Fabric filter
baghouse (existing).
----------------------------------------------------------------------------------------------------------------
* The facility is not required to install the listed technology to meet the BART limit.
Affected Class I Areas: Nine Class I areas are within 300 km of the
Nelson Lime Plant. Their nearest borders range from 24 km to 289 km
away, with the Grand Canyon the closest and other areas more than 100
km away. The highest baseline visibility impact from the Nelson Plant
is 1.79 dv at Grand Canyon NP followed by 0.31 at Sycamore Canyon WA
and 0.28 at Zion NP. The cumulative sum of visibility impacts over all
the Class I areas is 3.34 dv.
Facility Overview: The Nelson Plant processes limestone and
manufactures lime near Peach Springs in Yavapai County, Arizona. The
limestone processing plant consists of a quarry mining operation, a
limestone crushing and screening operation, a limestone kiln feed
system, a solid fuel handling system, two rotary lime kilns, front and
back lime handling systems, a lime hydrator, diesel electric
generators, fuel storage tanks, and other support operations and
equipment. The lime manufacturing equipment consists of two lime rotary
kilns (Kiln 1 and Kiln 2) and auxiliary equipment necessary for
receiving crushed limestone, processing it through the lime kilns, and
processing the lime kiln product. The lime kilns are used to convert
crushed limestone (CaCO3) into quicklime (CaO).
We primarily relied on four sources of information for our proposed
BART analyses and determinations. An initial BART analysis performed by
our contractor \74\ is available in the docket in the form of a final
contractor's report and associated modeling spreadsheets. We also
incorporated elements of a five-factor BART analysis \75\ provided by
Lhoist North America (LNA) of Arizona, owner of the Nelson Plant, that
includes control cost estimates and visibility modeling. Another key
document in our analysis is the Nelson Lime Plant's Title V Operating
Permit.\76\
---------------------------------------------------------------------------
\74\ Technical Analysis for Arizona and Hawaii Regional Haze
FIPs: Task 7: Five-Factor BART Analysis for Chemical Lime Company
Nelson, TEP Sundt (Irvington), and Catalyst Paper (Snowflake)
Plants, Contract No. EP-D-07-102, Work Assignment 5-12; Prepared for
EPA Region 9 by University of North Carolina at Chapel Hill, ICF
International, and Andover Technology Partners; October 9, 2012.
\75\ BART Five Factor Analysis, Lhoist North America Nelson Lime
Plant; Prepared by Trinity Consultants in Conjunction with Lhoist
North America of Arizona, Inc.; Project 131701.0061; August 2013.
(Public version dated September 27, 2013).
\76\ Title V Operating Permit and Technical Support Document for
the Nelson Lime Plant, Permit 42782, Issued August 8, 2011
by the Arizona Department of Environmental Quality.
---------------------------------------------------------------------------
Baseline Emissions Calculations: LNA's approach to establishing
baseline emissions was to first establish baseline emission factors in
lb/ton lime based on CEMS testing performed from March to June 2013.
Annual average baseline emissions were calculated by multiplying these
lb/ton emission factors by the highest annual lime production rate
observed over a period from 2001 to 2012. Maximum daily emissions were
calculated by multiplying lb/ton emission factors by the maximum daily
lime production rate observed during the March to June 2013 testing
period. As explained in further detail in our TSD, we consider LNA's
general approach appropriate, but also note that it represents a
conservatively high estimate of baseline emissions, and potentially
overstates the anticipated emission reductions and visibility benefit
from the evaluated control options. Nonetheless, given the lack of
measured annual emissions data, we concur with LNA's use of a
conservatively high baseline emissions estimate and we have
incorporated this estimate into our analysis. The baseline daily and
annual emission rates and associated production levels are shown in
Table 19.
Table 19--Nelson Lime Plant: Summary of Maximum Daily and Annual Baseline Emissions for NOX and SO2
--------------------------------------------------------------------------------------------------------------------------------------------------------
Lime production NOX SO2
--------------------------------------------------------------------------------------------------------------------
Max daily Max annual Year Emission Maximum emissions Emission Maximum emissions
Kiln \2\ -------------------------- factor \1\ -------------------------- factor \1\ -------------------------
------------- ------------- -------------
(tpy) (lb/ton (lb/day) (tpy) (lb/ton (lb/day) (tpy)
(tpd) lime) lime)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Kiln 1............................. 866 \3\ 258,508 2010 7.59 6,573 981 12.15 10,522 1,570
Kiln 2............................. 1,246 \4\ 378,296 2012 5.21 6,492 985 12.69 15,812 2,400
--------------------------------------------------------------------------------------------------------------------------------------------------------
\1\ Maximum emission factors observed during March, May and June 2013 CEMS testing.
\2\ Maximum daily rates occurring during the March 2013 CEMS testing.
\3\ 2010.
\4\ 2012.
1. Proposed Subject to BART
As part of our July 30, 2013 final rulemaking on the Arizona RH
SIP, we approved ADEQ's finding that Chemical Lime Nelson Plant (Nelson
Lime Plant) Kilns 1 and 2 were BART-eligible, but disapproved ADEQ's
determination that the Nelson Lime Plant was not subject to BART.\77\
In light of this disapproval, we have conducted our own evaluation of
whether Nelson Lime Plant is subject to BART, relying primarily on
emissions
[[Page 9337]]
data and modeling results provided by the facility's owner, LNA.\78\
---------------------------------------------------------------------------
\77\ 78 FR 46175 (codified at 40 CFR 52.145(g)(1)(i)).
\78\ BART Five Factor Analysis, Lhoist North America Nelson Lime
Plant; Prepared by Trinity Consultants in Conjunction with Lhoist
North America of Arizona, Inc.; Project 131701.0061; August 13, 2013
(Public version dated September 27, 2013).
---------------------------------------------------------------------------
As explained in the TSD, the baseline emissions estimates and the
corresponding modeling results provided by LNA are conservative (i.e.,
tending to overestimate rather than underestimate the impacts, in this
case). Nonetheless, we consider these results to be appropriate for
purposes of a subject-to-BART determination, as well as for the five-
factor BART analysis. LNA's modeling results indicate that the 98th
percentile impact for each of the 3 years modeled is well over 0.5 dv
at Grand Canyon National Park.\79\ Therefore, we propose to determine
that Nelson Lime Plant (Kilns 1 and 2) is subject to BART.
---------------------------------------------------------------------------
\79\ Id., Table 4-7. We note that the visibility modeling
performed by LNA used only the annual average Class I area
background concentrations, rather than the best 20 percent days
background concentrations. The use of annual average generally
results in lower visibility impacts than the best 20 percent days.
Therefore, had LNA used the best 20 percent days, the baseline
impacts would likely have been even greater.
---------------------------------------------------------------------------
2. Proposed BART for NOX
For our NOX BART analysis, we identified all available
control technologies, eliminated options that are not technically
feasible, and evaluated the control effectiveness of the remaining
control options. We then evaluated each control in terms of a five-
factor BART analysis and made a determination for BART.
a. Control Technology Availability, Technical Feasibility and
Effectiveness
EPA proposes to find that SNCR is the only technically feasible
control option to control NOX emissions with a control
efficiency of 50 percent. In order to determine a reasonable
performance standard for controlling NOX emissions, we
considered four available retrofit control technologies for
NOX on Kilns 1 and 2. These control technologies are a LNB,
mixing air technology (MAT), SCR, and SNCR. After evaluating each of
these technologies to eliminate technically infeasible options, we
determined that SNCR is the only remaining technically feasible control
option.
Low-NOX Burners: LNB are designed to reduce flame
turbulence, delay fuel/air mixing, and establish fuel-rich zones for
initial combustion. LNA indicated that it experimented with the
installation of bluff body LNB on the Nelson Lime Plant kilns in
2001.\80\ These LNB wore out in about six months, negatively affected
production, caused brick damage, and resulted in unscheduled shutdowns
of the kilns. We recognize that the staged combustion principle of LNB
can present operational difficulties and potential product quality
issues for lime production that are not exhibited in the cement
industry. At this time we consider LNB to be technically infeasible for
the Nelson Plant kilns, since we do not have any information to suggest
otherwise at this time. The technical feasibility of LNB will be re-
evaluated for lime kilns in subsequent reasonable progress planning
periods.
---------------------------------------------------------------------------
\80\ Described on page 5-2, ``BART Five Factor Analysis, Lhoist
North America Nelson Lime Plant'' (Public version dated September
27, 2013).
---------------------------------------------------------------------------
Mixing Air Technology: MAT is the practice of injecting a high
pressure air stream into the middle of a kiln to help mix the air
flowing through the kiln. While the theory behind MAT suggests that the
technology is effective at reducing NOX emissions, it is not
clear whether this control technology is effective on lime kilns. We
propose to eliminate MAT as not technically feasible for retrofit on
Kiln 1 and Kiln 2.
Selective Catalytic Reduction: This process uses ammonia in the
presence of a catalyst to selectively reduce NOX emissions
from exhaust gases. In SCR, ammonia, usually diluted with air or steam,
is injected through a grid system into hot flue gases that are then
passed through a catalyst bed to carry out NOX reduction
reactions. The catalyst is not consumed in the process but allows the
reactions to occur at a lower temperature. However, SCR is subject to
catalyst poisoning in high dust kiln exhausts. Therefore, SCR would
have to be placed after the particulate control systems. According to
LNA, given the operating temperature range for Kiln 1 and Kiln 2 at the
Nelson Lime Plant, the SCR catalyst would need to be located prior to
the kiln baghouses, which would result in poisoning or covering of the
catalyst. In addition, there are no SCR systems currently operating on
lime kilns. We propose to eliminate SCR as not technically feasible for
retrofit on Kiln 1 and Kiln 2.
Selective Non-Catalytic Reduction: SNCR is a technically feasible
option for reducing NOX emissions from the Nelson Lime Plant
kilns as shown in Table 20. This control technique relies on the
reduction of NOX in exhaust gases by injection of ammonia or
urea, without using any catalyst. This approach avoids the problems
related to catalyst fouling and poisoning attributed to SCR, but
requires injection of the reagents in the kiln at a temperature between
1600[emsp14][deg]F to 2000[emsp14][deg]F. Because no catalyst is used
to increase the reaction rate, the temperature window is critical for
conducting this reaction. LNA has not conducted any detailed design
work for an SNCR system for the Nelson Plant kilns, but anticipates
that a 50 percent reduction is achievable based on LNA's experience
with operating a urea-injection system at another LNA lime plant.
Table 20--Nelson Lime Plant: SNCR Control Efficiency for Baseline Emissions
----------------------------------------------------------------------------------------------------------------
Control Emission Maximum emission rate Emissions
efficiency factor -------------------------------- removed
Control option -------------------------------- ---------------
(%) (lb/ton lime) (lb/day) (tpy) (tpy)
----------------------------------------------------------------------------------------------------------------
Kiln 1:
Baseline.................... .............. 7.59 6,573 981
SNCR........................ 50 3.80 3,286 491 491
Kiln 2:
1Baseline................... .............. 5.21 6,492 985
SNCR........................ 50 2.61 3,246 493 493
----------------------------------------------------------------------------------------------------------------
[[Page 9338]]
b. BART Analysis for NOX
EPA conducted a five-factor BART analysis of SNCR to evaluate its
cost-effectiveness and visibility benefit. This analysis indicates that
SNCR is cost-effective and results in visibility improvement.
Cost of Compliance: The following table provides LNA's estimated
cost for installation and operation of SNCR. Capital cost estimates
developed by LNA relied primarily on vendor cost estimates and LNA's
experience at other lime plants, with the remainder of the capital
costs calculated using the cost methodology contained in EPA's Control
Cost Manual. LNA has asserted a confidential business information (CBI)
claim regarding certain annual operating costs such as reagent usage
and auxiliary power costs. As a result, we have prepared our own
independent estimate of annual operating costs based upon a combination
of publicly available data and certain general assumptions as described
in the Contractor's Report.\81\ Table 21 is a summary of the estimated
cost for installation and operation of SNCR.
---------------------------------------------------------------------------
\81\ Our estimate of annual operating costs is in the
spreadsheet ``Nelson Control Costs 2013-10-21.xlsx'' in the docket.
Table 21--Nelson Lime Plant: Estimated Cost for SNCR
--------------------------------------------------------------------------------------------------------------------------------------------------------
Capital cost Annualized Annual Total annual Emission Cost-
---------------- capital cost operating cost cost reduction effectiveness
Kiln -------------------------------------------------------------------------------
($) ($) ($) ($/yr) (tpy) ($/ton)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Kiln 1.................................................. $450,000 $42,477 $358,459 $400,936 491 $817
Kiln 2.................................................. 450,000 42,477 354,981 397,458 493 807
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: SNCR systems
require electricity to operate the blowers and pumps, which will likely
involve fuel combustion that will generate emissions. Overall, while
the generation of the required electricity will result in emissions,
the emissions should be low compared to the reduction in NOX
that would be gained by operating an SNCR system. The operation of SNCR
systems on Kiln 1 and Kiln 2 would require that either urea or ammonia
be stored on site. The storage of the chemicals does not result in a
direct non-air quality impact. However, the potential for the urea or
ammonia that would be stored to leak or otherwise be released from the
storage vessels means there is the potential for both air and non-air
quality related impacts. The storage of these chemicals does not
significantly impact the BART determination.
Pollution Control Equipment in Use at the Source: The presence of
existing pollution control technology at each source is reflected in
our BART analysis in two ways: first, in the consideration of available
control technologies, and second, in the development of baseline
emission rates for use in cost calculations and visibility modeling.
Air pollution control equipment in use at the Nelson Lime Plant
includes a number of baghouses, two multi-cyclone dust collectors, and
a Ducon wet scrubber to control particulate matter emissions. The
facility does not currently have control equipment for NOX
and SO2. The kilns are allowed to burn coal, petroleum coke,
fuel oil, or any combination of these fuels.
Remaining Useful Life of the Source: Since we are not aware of any
enforceable shutdown date for the Nelson Lime Plant, we have used a 20-
year amortization period, as noted in the EPA Cost Control Manual, as
the remaining useful life of the kilns.
Degree of Visibility Improvement: LNA performed a visibility
analysis \82\ to assess the visibility improvement associated with
SNCR. LNA performed dispersion modeling using the CALPUFF modeling
system, which consists of the CALPUFF dispersion model, the CALMET
meteorological data processor, and the CALPOST post-processing program.
The specific program versions that were relied upon in the analysis
match the program versions relied upon by EPA's contractor, the
University of North Carolina at Chapel Hill and ICF International (UNC/
ICF), in the BART analyses that they prepared for select sources,
including the Nelson Plant. Most of the same data and parameter
settings relied upon in the analysis are the same data and parameter
settings that were relied upon in the contractor's report. Compared to
the UNC work, LNA used updated higher base case SO2 and NOx
emissions, lower PM emissions, and lower stack exit velocities. LNA's
analysis included tables of visibility impacts and the improvement from
controls, including results for the individual model years 2001, 2002,
and 2003, and it used visibility method ``8a'' and focused on the
highest value from among the three years' 98th percentiles. In order to
put all the facilities on the same footing, EPA post-processed the
modeling files provided by LNA using the approach followed for the
other facilities.
---------------------------------------------------------------------------
\82\ BART Five Factor Analysis, Lhoist North America Nelson Lime
Plant, Trinity Consultants, August 2013.
---------------------------------------------------------------------------
Table 22 represents the 98th percentile by the 22nd high over the
2001-2003 period using visibility method ``8b.'' Using the EPA
procedure, the maximum impact still occurs at the Grand Canyon, at 1.8
dv. The 98th percentile impacts at other Class I areas are about 0.3 dv
or below, and the cumulative impact is 3.3 dv. The maximum visibility
improvement due to SNCR is 0.58 dv, and cumulative improvement is 0.85
dv. There is little improvement at areas other than the Grand Canyon.
These improvements yield a visibility cost-effectiveness of $1.4
million/dv using the maximum, and $0.9 million/dv using the cumulative
improvement. These visibility improvements support the choice of SNCR
as BART for NOX.
[[Page 9339]]
Table 22--Nelson Lime Plant: Visibility Impact and Improvement From NOX Controls
----------------------------------------------------------------------------------------------------------------
Visibility Visibility
impact improvement
Class I area Distance (km) -------------------------------
Base case SNCR (ctr1)
----------------------------------------------------------------------------------------------------------------
Bryce Canyon NP................................................. 235 0.20 0.06
Grand Canyon NP................................................. 24 1.79 0.58
Joshua Tree NP.................................................. 238 0.23 0.02
Mazatzal WA..................................................... 206 0.15 0.01
Pine Mountain WA................................................ 199 0.15 0.02
Sierra Ancha WA................................................. 289 0.11 0.01
Superstition WA................................................. 288 0.13 0.01
Sycamore Canyon WA.............................................. 132 0.31 0.07
Zion NP......................................................... 183 0.28 0.08
Cumulative (sum)................................................ .............. 3.34 0.85
Maximum......................................................... .............. 1.79 0.58
CIAs >= 0.5 dv........................................ .............. 1 1
Million $/dv (cumul. dv)........................................ .............. .............. $0.9
Million $/dv (max. dv).......................................... .............. .............. $1.4
----------------------------------------------------------------------------------------------------------------
c. Proposed BART Determination for NOX
We propose to find that BART for NOX for Kilns 1 and 2
is SNCR, and are proposing a BART emission limit for Kiln 1 of 3.80 lb/
ton lime and for Kiln 2 of 2.61 lb/ton lime on a 30-day rolling basis,
as demonstrated through the use of a CEMS. We consider SNCR to be a
very cost-effective control option for Kilns 1 and 2, at $817/ton and
$807/ton, respectively. In addition, we consider the anticipated
visibility benefit from SNCR, 0.58 dv at Grand Canyon National Park and
0.85 cumulatively at all Class I areas within 300 km, to be
substantial. In considering the other factors, we do not consider their
impact substantial relative to the cost and visibility factors. We note
that the remaining useful life of the source is reflected in the
evaluation of cost of compliance through the use of a 20-year
amortization period in control cost calculations. Since there is no
existing NOX control technology in use on the kilns,
baseline emissions reflect uncontrolled NOX emissions. In
examining energy and non-air quality impacts, while we note certain
impacts associated with SNCR, we do not consider these impacts
sufficient to warrant its elimination as a control option.
We propose to require compliance with this requirement within three
years after the effective date of the final rule. A 2006 Institute of
Clean Air Companies (ICAC) study indicated that the installation time
for a typical SNCR retrofit, from bid to startup-up, is 10-13
months.\83\ In relation to other industrial sources, such as fossil
fuel boilers, there are a limited number of examples of SNCR
installation on lime kilns. Given this relative lack of information
regarding SNCR installation schedules on lime kilns, we consider three
years to be an appropriate length of time to design, install, and test
an ammonia injection system for a lime kiln. In addition, we are also
proposing regulatory text that includes monitoring, reporting, and
recordkeeping requirements associated with this emission limit. As part
of the proposed monitoring requirements, we are including a requirement
to monitor rates of ammonia injection in order to ensure proper
operation of the SNCR in a manner that minimizes ammonia emissions.
---------------------------------------------------------------------------
\83\ See ``Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources,'' Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
3. Proposed BART for SO2
For our BART analysis, we identify all available control
technologies, eliminate options that are not technically feasible, and
evaluate the control effectiveness of the remaining control options. We
then evaluate each control in terms of a five-factor BART analysis and
make a determination for BART.
a. Control Technology Analysis for SO2
EPA proposes to find that DSI and switching to lower sulfur fuel
are technically feasible controls, while wet or semi-dry scrubbing is
not technically feasible.
Wet or Semi-Dry Scrubbing: We do not consider wet or dry scrubbing
to be a feasible technology to control SO2 emissions for
this source. Wet scrubbing involves passing flue gas downstream from
the main particulate matter control device through a sprayed aqueous
suspension of lime or limestone that is contained in a scrubbing
device. The SO2 reacts with the scrubbing reagent to form
lime sludge that is collected. The sludge usually is dewatered and
disposed of at an offsite landfill. However, LNA has concluded, and we
agree, that there is not sufficient water available for this type of
system. According to LNA, two ground water wells supply about 106
gallons per minute (gpm) to the Nelson Plant, which currently uses
about 80 gpm. Therefore, only 26 gpm of water is available for a
scrubbing system that, even for a semi-dry scrubbing system that has
lower water requirements than wet scrubbing, would require about 117
gpm. Moreover, a 1998 hydrologic report indicates that the prospects
for developing additional wells, even low-yield wells, on the Nelson
property are poor.\84\ After reviewing the hydrologic report and the
vendor estimate of water requirements for a semi-dry scrubber, we agree
with this assessment.
---------------------------------------------------------------------------
\84\ See ``Results of Hydrogeologic Investigations for
Development of Additional Water Supply, Chemical Lime Company,
Nelson Plant, Yavapai County, AZ,'' July 8, 1998.
---------------------------------------------------------------------------
Dry Sorbent Injection: DSI involves the injection of powdered
absorbent directly into the flue gas exhaust stream. The sorbent reacts
with SO2 in the exhaust to form solid particles that are
then removed by a particulate matter control device downstream of the
sorbent injection. DSI is a simple system that generally requires a
sorbent storage tank, feeding mechanism, transfer line and blower, and
an injection device. DSI is generally considered technically feasible
for the cement industry, although the level of control effectiveness
may vary based upon site-specific conditions. We consider this option
technically feasible for lime kilns. LNA has not included information
in its analysis indicating
[[Page 9340]]
that DSI would be infeasible for the Nelson Plant kilns.
Lower Sulfur Fuel: The lower sulfur fuel option described by LNA
involves changing the proportion of coal and petroleum coke used as a
fuel blend. LNA currently uses a blend of 27 percent coal and 73
percent petroleum coke, on a mass basis, as the fuel for the kilns.
Since coke has about four to five times more sulfur than coal, it is
possible to decrease the sulfur in the fuel blend by increasing the
proportion of coal. However, an increase in coal in the fuel blend will
also increase the ash content of the fuel blend. Ash in the fuel can
disrupt operations due to the buildup of ash rings in the kilns. A fuel
blend with an ash content of about 6.5 percent or less must be used in
order to avoid these operational challenges.
As noted in fuel usage and purchase records, the Nelson Plant
currently operates on a coal and petroleum coke mixture. As a result,
we consider adjusting the coal/coke ratio in the fuel mixture to be a
technically feasible option. We note, however, that since the BART
Guidelines do not require fuel supply changes to be considered as a
control option, we have typically not considered changes in fuel in
BART analyses.\85\ However, because LNA included lower sulfur fuel in
its analysis, we have retained it as a control option.
---------------------------------------------------------------------------
\85\ 40 CFR Part 51, Appendix Y, Section IV.D.1.5, ``STEP 1: How
do I identify all available retrofit emission control techniques?''
---------------------------------------------------------------------------
b. BART Analysis for SO2
EPA conducted a five-factor BART analysis of the two technically
feasible control options, DSI and lower sulfur fuel, to evaluate the
cost-effectiveness and visibility benefit of each option along with any
effect on the other factors.
Cost of Compliance: Our consideration of the cost of compliance
focuses primarily on the cost-effectiveness of each control option as
measured in cost per ton and incremental cost per ton. We estimate the
SO2 emissions rates for DSI and lower sulfur fuel as shown
in Table 23, and the cost-effectiveness of these options as shown in
Table 24. DSI has a control efficiency of 40 percent that results in
about 1,588 tpy of SO2 removed from both kilns. Lower sulfur
fuel has a control efficiency of 23.3 percent that results in about 925
tpy of SO2 removed from both kilns. Based on the total
annual costs of controlling SO2 emissions at both kilns, DSI
would cost an average of about $4,200 per ton removed and lower sulfur
fuel about $860 per ton removed. Since there is no existing
SO2 control technology in use in the plant, baseline
emissions reflect uncontrolled SO2 emissions.
While we consider it appropriate to use 40 percent control
efficiency \86\ for DSI, we are inviting comment on the control
effectiveness of 23.3 percent for a lower sulfur fuel blend based on
the ratio of coal (1.15 percent sulfur) to petroleum coke (5.64 percent
sulfur). LNA estimates that the maximum coal-to-coke ratio to maintain
overall fuel ash content below 6.5 percent is a 50 percent coal to 50
percent coke fuel mixture. A 50/50 mix corresponds to a fuel sulfur
reduction of 1.13 percentage points, which represents a 23.3 percent
reduction from the current fuel mixture. Based on a review of coal and
coke properties along with historical fuel usage at the Nelson Plant,
we agree with the use of a 50/50 coal-to-coke ratio and 23.3 percent
control effectiveness. However, LNA cites operational issues with fuel
ash content above 6.5 percent. Since ash is a contaminant that can
adversely affect lime product quality, we are seeking comment regarding
the extent to which it is appropriate to use fuel ash content of 6.5
percent as the upper bound for determining fuel mixture ratio. We may
finalize a different fuel mixture ratio based upon the comments we
receive.
---------------------------------------------------------------------------
\86\ While the control efficiency for DSI is much higher for
cement kilns, LNA conducted onsite testing of DSI on the lime kilns
at the Nelson Plant that demonstrated it is appropriate to use 40
percent control efficiency. The docket includes a comparison of
LNA's tests of DSI to the analysis in our contractor's report.
---------------------------------------------------------------------------
In estimating the costs of compliance, LNA relied on a vendor quote
for purchased equipment provided by Noltech dated May 22, 2013, with
the remainder of the capital costs calculated using the cost
methodology contained in EPA's Control Cost Manual.\87\ While these
capital costs are higher than those estimated by our contractor, we
consider the use of the Noltech vendor quote for the Nelson Plant
reasonable, and have incorporated it into our evaluation of the costs
of compliance. With regard to annual operating & maintenance costs, LNA
has asserted a confidential business information (CBI) claim regarding
certain annual operating costs such as reagent usage. As a result, we
have prepared our own independent estimate of annual operating costs
based upon a combination of publicly available data and certain
assumptions as described in the contractor's report. Detailed cost
calculations can be found in the docket.\88\
---------------------------------------------------------------------------
\87\ Vendor quote included as an attachment to BART Five Factor
Analysis, Lhoist North America Nelson Lime Plant; (Public version
dated September 27, 2013).
\88\ See spreadsheet ``Nelson Control Costs 2013-10-24.xlsx'' in
the docket.
Table 23--Nelson Lime Plant: SO2 Control Option Emission Estimates
----------------------------------------------------------------------------------------------------------------
Control Emission Maximum emission rate
SO2 control technology efficiency factor (lb/ -------------------------- Removed
(%) ton lime) lb/day Tpy (tpy)
----------------------------------------------------------------------------------------------------------------
Kiln 1:
Baseline................................... ........... 12.15 10,526 1,571 ...........
Lower Sulfur Fuel Blend.................... 23.30 9.32 8,073 1,205 366
Dry Sorbent Injection...................... 40 7.29 6,316 943 628
Kiln 2:
Baseline................................... ........... 12.69 15,808 2,400 ...........
Lower Sulfur Fuel Blend.................... 23.30 9.73 12,125 1,841 559
Dry Sorbent Injection...................... 40 7.61 9,485 1,440 960
----------------------------------------------------------------------------------------------------------------
[[Page 9341]]
Table 24--Nelson Lime Plant: SO2 Control Option Cost-Effectiveness
--------------------------------------------------------------------------------------------------------------------------------------------------------
Capital Annual Annual Total Emission Cost-effectiveness ($/
cost direct indirect annual cost reduction ton)
SO2 control technology ------------- costs costs ---------------------------------------------------
--------------------------
($) ($/yr) ($/yr) ($/yr) (tpy) Average Incremental
--------------------------------------------------------------------------------------------------------------------------------------------------------
Kiln 1:
Lower Sulfur Fuel Blend.................................. ........... ........... ........... $313,096 366 $856 ...........
Dry Sorbent Injection.................................... $2,497,559 $371,174 $2,621,832 2,621,832 628 4,174 $8,803
Kiln 2:
Lower Sulfur Fuel Blend.................................. ........... ........... ........... 458,179 559 819 ...........
Dry Sorbent Injection.................................... 2,497,559 371,174 3,895,774 3,895,774 960 4,058 8,576
--------------------------------------------------------------------------------------------------------------------------------------------------------
Pollution Control Equipment in use at the Source: The presence of
existing pollution control technology at the Nelson Plant is reflected
in the BART analysis in two ways: first, in the consideration of
available control technologies, and second, in the development of
baseline emission rates for use in cost calculations and visibility
modeling. In the case of SO2, the kilns at the Nelson Plant
do not operate with any existing control technology. This is reflected
in the baseline emission rates, which represent uncontrolled
SO2 emissions.
Energy and non-air quality environmental impacts: Regarding the
first option, DSI systems require electricity for operation. The
generation of the electricity needed to operate a DSI system will
likely involve fuel combustion that will generate emissions. Emissions
also are associated with the transport, handling, and storage of
sorbent. Overall, while the use of DSI will cause emissions from select
activities, the emissions should be low compared to the reduction in
SO2 that would be gained by operating a DSI system.
Regarding the second option, using a lower sulfur fuel blend means LNA
will obtain more of the energy for lime production from coal and less
of the energy from coke. Since the heating value of coke is slightly
higher than the heating value of coal, it is likely that LNA will burn
more total mass of fuel as a result of substituting some coal for coke.
While burning a lower sulfur fuel blend will likely result in a
reduction in SO2 emissions, it will involve the overall use
of greater quantities of coal, which may result in a collateral
increase of other pollutants such as NOX and CO.
Remaining Useful Life of the Source: We are considering the
``remaining useful life'' of the kilns as one element of the overall
cost analysis as allowed by the BART Guidelines. In the absence of any
enforceable closure date, we have used a 20-year amortization period
described in the EPA Cost Control Manual as the remaining useful life
for the control options considered for the Nelson Plant kilns. Since
there is no capital costs associated with using a lower sulfur fuel
blend, the remaining useful life of the kilns is not a factor in the
evaluation of this technology.
Degree of Visibility Improvement: As was the case for
NOX, EPA post-processed LNA's modeling results for
SO2 controls. The greatest improvement from DSI is 0.2 dv,
occurring at the Grand Canyon, with improvements at other areas a third
or less than this. The cumulative improvement is 0.6 dv. The maximum
and cumulative improvements from switching to lower sulfur fuel are
roughly half of these amounts. While visibility improvement by itself
could support either DSI or lower sulfur fuel as BART, lower sulfur
fuel is favored by its much lower average cost-effectiveness at $819-
856/ton compared to over $4000 for DSI. Baseline and control option
emission rates used in SO2 control scenario modeling are
summarized in Table 25 with the modeling results in Table 26.\89\
---------------------------------------------------------------------------
\89\ These results are from EPA's post-processing of LNA's
modeling. See the TSD for a discussion of the differences between
EPA's results and the results reported by LNA in their BART
analysis.
Table 25--Nelson Lime Plant: SO2 Control Model Emission Rates
----------------------------------------------------------------------------------------------------------------
Control Emission Maximum 24-hr model emission rate
efficiency factor --------------------------------------
SO2 control technology --------------------------
% lb/ton lime lb/day lb/hr g/s
----------------------------------------------------------------------------------------------------------------
Kiln 1:
Baseline................................... ........... 12.15 10,526 439 55
Lower Sulfur Fuel Blend.................... 23.30 9.32 8,073 336 42
Dry Sorbent Injection (SBC)................ 40 7.29 6,315 263 33
Kiln 2:
Baseline................................... ........... 12.69 15,808 659 83
Lower Sulfur Fuel Blend.................... 23.30 9.73 12,125 505 64
Dry Sorbent Injection (SBC)................ 40 7.61 9,489 395 50
----------------------------------------------------------------------------------------------------------------
Table 26--Nelson Lime Plant: SO2 Control Option Visibility Modeling Results
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
Distance impact --------------------------
Class I area (km) -------------- Low-S fuel
Base case DSI (ctr2) (ctr3)
----------------------------------------------------------------------------------------------------------------
Bryce Canyon NP........................................... 235 0.20 0.03 0.02
[[Page 9342]]
Grand Canyon NP........................................... 24 1.79 0.21 0.10
Joshua Tree NP............................................ 238 0.23 0.07 0.04
Mazatzal WA............................................... 206 0.15 0.04 0.02
Pine Mountain WA.......................................... 199 0.15 0.04 0.02
Sierra Ancha WA........................................... 289 0.11 0.04 0.02
Superstition WA........................................... 288 0.13 0.04 0.02
Sycamore Canyon WA........................................ 132 0.31 0.06 0.04
Zion NP................................................... 183 0.28 0.04 0.02
Cumulative (sum).......................................... ........... 3.34 0.57 0.29
Maximum................................................... ........... 1.79 0.21 0.10
CIAs >= 0.5 dv.................................. ........... 1 0 0
Million $/dv (cumul. dv).................................. ........... ............ $11.5 $2.6
Million $/dv (max. dv).................................... ........... ............ $30.7 $8.1
----------------------------------------------------------------------------------------------------------------
c. Proposed BART Determination for SO2
We propose to find that BART for SO2 is the use of a
lower sulfur fuel blend with an emission limit of 9.32 lb/ton for Kiln
1 and 9.73 lb/ton for Kiln 2 \90\ on a rolling 30-day basis. In
evaluating the costs of compliance, we note that we consider DSI and
lower sulfur fuel to both be cost-effective control options, with
average cost-effectiveness values of approximately $800/ton and $4,000/
ton, respectively. In evaluating anticipated visibility benefit, while
DSI is anticipated to achieve the greatest visibility improvement (0.21
dv at Grand Canyon), this amount of visibility improvement is not
large, nor is the benefit anticipated for the next most stringent
control option, lower sulfur fuel (0.10 dv at Grand Canyon). In
considering the other factors, there is no significant effect on the
outcome of the cost and visibility analyses. The lack of existing
control technology is reflected in the baseline in the form of
uncontrolled SO2 emissions. In examining energy and non-air
quality impacts, we note that there may be certain collateral increases
in emissions, but that these increases are outweighed by the emission
reductions achieved by implementing the control technology and do not
warrant their elimination. The remaining useful life of the source is
reflected in the evaluation of the cost of compliance. We consider both
DSI and use of lower sulfur fuel to be cost-effective, but note that
the most stringent option, DSI, is considerably less cost-effective
than the use of lower sulfur fuel, with an incremental cost-
effectiveness, relative to lower sulfur fuel, of approximately $9,000/
ton. As a result, although DSI is the most stringent control option,
the visibility benefit it achieves is not large, and is achieved at a
very high incremental cost relative to the next most stringent control
option. Based on this information, we propose to find that BART for
SO2 is the use of a lower sulfur fuel blend.
---------------------------------------------------------------------------
\90\ The differing emission limits are due to the different
baseline performance of the two kilns.
---------------------------------------------------------------------------
4. Proposed BART for PM10
For our BART analysis, we identified fabric filter baghouses, the
existing control technology for PM10 on Kilns 1 and 2, as
the most stringent control available for this type of source.
a. Control Technology Analysis for PM10
The Nelson Plant, as a major source of hazardous air pollutants
(HAPs), is subject to the Maximum Achievable Control Technology (MACT)
Standard for Lime Manufacturing Plants, and is required to meet an
emission limit of 0.12 lbs PM/TSF (ton of stone feed).\91\ The BART
Guidelines provide that unless there are new technologies subsequent to
the MACT standards that would lead to cost-effective increases in the
level of control, one may rely on the MACT standards for purposes of
BART.\92\ Based on information developed as part of the Lime MACT, we
estimate that existing fabric filter upgrades would result in annual
costs of $94,500.\93\ As noted in LNA's BART analysis, baseline PM
emissions for the two kilns, based on PM filterable stack test data and
annual lime production, are approximately 8 tpy and 15 tpy.\94\ This
would result in an average cost-effectiveness of about $6,300 to
$12,000/ton.
---------------------------------------------------------------------------
\91\ 40 CFR Part 63, Subpart AAAAA, Table 1, Item 1 for existing
lime kilns with no wet scrubber prior to 2005.
\92\ 40 CFR Part 51, Appendix Y, Section IV.C.
\93\ Annual costs as described in the Economic Impact Analysis
for the Lime Manufacturing MACT Standard (EPA-452/R-03-013), Table
3-2, Model Kiln F. Adjusted from 1997 to 2013 dollars using the
consumer price index, available at ftp://ftp.bls.gov/pub/special.requests/cpi/cpiai.txt.
\94\ As described in the LNA Nelson BART Analysis, Table 4-5.
---------------------------------------------------------------------------
b. BART Analysis for PM10
The BART Guidelines provide that, in instances where a source
already has the most stringent controls available (including all
possible improvements), it is not necessary to complete each step of
the BART analysis. Further, as long as the most stringent controls
available are made federally enforceable for the purpose of
implementing BART for that source, one may skip the remainder of the
analysis, including the visibility analysis.\95\
---------------------------------------------------------------------------
\95\ 40 CFR Part 51, Appendix Y, Section IV.D.9.
---------------------------------------------------------------------------
c. Proposed BART Determination for PM10
We propose a BART emission limit of 0.12 lb/TSF to control
PM10 at Kilns 1 and 2 based on the use of the existing
fabric filter baghouses and commensurate with the MACT standard that
applies to this source. We seek comment on any cost-effective upgrades
or improvements that may result in a lower emission limit. We propose
to require compliance with this requirement within 6 months after the
effective date of the final rule. We also propose regulatory text that
includes monitoring, reporting, and recordkeeping requirements
associated with this emission limit that is found at the end of this
notice.
C. Hayden Smelter
Summary: EPA proposes to find that the ASARCO Hayden Smelter is
subject to BART for NOX in addition to SO2 as
[[Page 9343]]
determined by the State. ASARCO must capture and control SO2
emissions from the converter units that are subject to BART. In the
current method of operation, thousands of tons of SO2 from
these units are vented to the atmosphere with no pollution control. One
method to control SO2 emissions from the converter units is
to install and operate a second double contact acid plant with a
control efficiency of about 99.8 percent on a 30-day rolling average.
We estimate the annual cost of constructing and operating a second acid
plant to control SO2 emissions is about $872 per ton of
SO2 removed. While we consider the cost of a new acid plant
to be reasonable, we are proposing a performance standard as BART
rather than prescribing a particular method of control. For
NOX, we propose to set an annual emission limit of 40 tpy
from the BART-eligible units, based on our proposed determination that
no NOX controls are needed for BART at the Hayden Smelter.
Finally, we are proposing an emission limit and associated compliance
requirements for PM10.
Affected Class I Areas: Twelve Class I areas are within 300 km of
the Hayden Smelter. Their nearest borders range from 48 km to 239 km
away. Galiuro WA and Superstition WA are the closest, followed by
Saguaro NP and Sierra Ancha WA. The highest baseline 98th percentile
visibility impact is 1.7 dv at Superstition, with impacts at Galiuro
slightly lower. Baseline visibility impacts at each of the twelve areas
exceed 0.5 dv. The cumulative sum of visibility impacts over all the
Class I areas is 12.1 dv.
Facility Overview: ASARCO Hayden Smelter is a batch-process copper
smelter in Gila County, Arizona. We previously approved ADEQ's
determination that converters 1, 3, 4 and 5 and Anode Furnaces 1 and 2
at the facility are BART-eligible.\96\ We also approved ADEQ's
determination that these units are subject to BART for SO2
and that BART for PM10 at ASARCO Hayden is no additional
controls. However, we disapproved ADEQ's determination that existing
controls constitute BART for SO2 and that the units are not
subject to BART for NOX. In light of these disapprovals and
our FIP duty for regional haze in Arizona, we are required to
promulgate a FIP to address BART for SO2 and NOX.
---------------------------------------------------------------------------
\96\ 78 FR 46412 (July 30, 2013). Please refer to the TSD for a
description of these units.
---------------------------------------------------------------------------
Baseline Emissions Calculations: Since neither ASARCO nor ADEQ
identified baseline emissions for the Hayden Smelter, we calculated
baseline emissions for SO2 and NOX. For
SO2, we used as the baseline the average of the two highest
emitting years from the last five years that ASARCO reported to ADEQ.
For NOX, we estimated emission rates based on the rated
natural gas capacity of the burners in the four subject-to-BART
converters and the two anode furnaces.\97\ As indicated in Table 27,
the majority of the source's SO2 emissions (20,341 tpy of a
total of 22,621 tpy) are process emissions from the converters. These
process SO2 emissions are collected through a secondary
capture system, but are emitted uncontrolled through an annular stack
that bypasses the existing double contact acid plant. While our BART
analysis focuses on these uncontrolled SO2 emissions from
the converters, we also evaluated improved control of the
SO2 emissions from the existing acid plant and from the
anode furnaces as well as controlling NOX emissions from all
the BART units.
---------------------------------------------------------------------------
\97\ ASARCO Hayden Title V permit.
Table 27--Hayden Smelter: BART Baseline Emissions
[Tons per year]
----------------------------------------------------------------------------------------------------------------
Converters
-----------------------------------------
Existing Annular Anode
acid plant stack furnaces Total
(primary (secondary Uncaptured
capture) capture)
----------------------------------------------------------------------------------------------------------------
SO2.......................................... 1,034 20,341 1,209 37 22,621
------------------------------------------------------------------
NOX.......................................... 31 19 50
----------------------------------------------------------------------------------------------------------------
Modeling Overview: EPA is relying on modeled baseline and post-
control impacts of the ASARCO Hayden Smelter using stack parameters
provided by ASARCO in response to a 2013 EPA information request.\98\
We also modeled using stack parameters based on a 2012 stack test.\99\
Stack exit temperatures were comparable for these two models, but the
exit velocities from the 2012 stack test were far lower than those
provided by ASARCO in 2013. The 2012 stack test parameters resulted in
visibility impacts and control benefits about 10 percent higher than
the model using the 2013 parameters. We are conservatively using the
2013 ASARCO parameters to evaluate controls, since using the 2012
parameters would yield even greater visibility improvements. For both
sets of modeling runs, EPA used emission rates that were developed
using information provided by ASARCO.
---------------------------------------------------------------------------
\98\ Letter from Jack Garrity, ASARCO to Thomas Webb, EPA, July
11, 2013; attached Memorandum from Ralph Morris and Lynsey Parker,
ENVIRON, to Eric Hiser, Jorden, Bischoff and Hiser, PLC, March 4,
2013.
\99\ ASARCO Hayden CEMS Test Report, Energy and Environmental
Measurement Corporation, Test date: September, 2012.
---------------------------------------------------------------------------
1. BART Analysis and Determination for SO2 From Converters
a. Control Technology Availability, Technical Feasibility and
Effectiveness
EPA identified two available technology options to control the
20,341 tons of SO2 emissions from the annular stack that are
captured by a secondary collection system, but are released
uncontrolled through the annular stack. These options are to construct
and operate a second double contact acid plant or install a wet
scrubber on the annular portion of the existing stack. In addition, we
found that ASARCO could add a tail stack scrubber to the existing acid
plant to address the remaining emissions that are not converted and
removed as sulfuric acid by the acid plant. Regarding technical
feasibility, we note that ASARCO Hayden currently uses a double contact
acid plant to control SO2 emissions captured by the primary
capture system. Wet scrubbing also is commonly used in many industries
to control SO2. Thus, we find
[[Page 9344]]
that the double contact acid plant and wet scrubbing are technically
feasible. In terms of control effectiveness, ASARCO indicated in a
letter \100\ to EPA that its double contact acid plant is capable of
recovering 99.8 percent of the SO2 vented to it.\101\ In the
same letter, ASARCO noted that the expected control effectiveness of
wet scrubbing is 85 percent. We used these removal efficiencies in our
five-factor analyses. These analyses are explained in the TSD and
summarized below.
---------------------------------------------------------------------------
\100\ Letter from Jack Garrity, ASARCO to Thomas Webb, EPA, July
11, 2013.
\101\ Ibid.
---------------------------------------------------------------------------
b. Option 1: Double Contact Acid Plant for Secondary Capture
Cost of Compliance: EPA determined the cost-effectiveness of a new
double contact acid plant is $872 per ton of SO2 removed as
shown in Table 28. As explained in the TSD, we conservatively estimated
the cost of construction of a double contact acid plant to be
$81,621,297. The annualized capital costs are based on a 20-year
lifespan and a seven percent interest rate. We applied a control
efficiency of 99.8 percent, which the existing acid plant is currently
achieving with limited cesium catalyst. The emission reduction was
applied to the secondary capture system baseline emissions. This cost
analysis does not include the offsetting value of any sulfuric acid
produced and sold. It does assume full catalyst replacement every other
year and air preheating with natural gas for 8,760 hours per year.
Table 28--Hayden Smelter Option 1: Second Double Contact Acid Plant
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual Total annual Tons SO2 Control $/ton SO2
Capital cost capital cost variable cost cost reduced efficiency removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$81,621,297....................................... $7,704,573 $10,006,010 $17,710,483 20,341 99.8% $872
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: Controlling
secondary capture with a sulfuric acid plant at the Hayden Smelter
would require energy to heat inlet air from approximately
177[emsp14][deg]F to 735[emsp14][deg]F. This would require a heat input
of approximately 114 MMBtu/hour and could require 1,200 MMscf of
natural gas per year, resulting in up to 30 tpy of NOX
emissions.\102\ This assumes 100 percent of the needed heat results
from natural gas combustion. Non-air quality impacts from a second acid
plant are not expected to be significant given that ASARCO already has
the capacity to handle and store the much larger quantities of sulfuric
acid produced by the primary acid plant.
---------------------------------------------------------------------------
\102\ This is based on the AP 42 factor for low-NOX
burners.
---------------------------------------------------------------------------
Pollution Control Equipment in Use at the Source: As noted above
and further described in the TSD, a portion of the emissions from the
converters are controlled by a gas cleaning plant to remove particulate
matter and a double contact sulfuric acid plant that converts
SO2 to sulfuric acid. We considered these controls as part
of our analysis of available control technologies and in developing
baseline emission rates for use in cost calculations and visibility
modeling.
Remaining Useful Life of the Source: The BART-eligible converters
have each been in place for about 40 years or longer. ASARCO has not
indicated that any of the converters would need to be replaced during
the 20-year capital cost recovery period.
Degree of Visibility Improvement: Controlling SO2
emissions through a second double contact acid plant at a 98.8 percent
efficiency results in visibility improvement in 12 Class I areas in
Arizona and New Mexico as indicated in Table 29. Based on air quality
modeling, visibility improvement from controlling SO2 by
constructing a new acid plant to control converter emissions from the
secondary capture system is 1.5 dv at Superstition, and nearly the same
at Galiuro. Eleven of the Class I areas improve by at least 0.5 dv. The
cumulative improvement is 10.3 dv. The large visibility improvement at
many Class I Areas supports the choice of a new acid plant as BART for
SO2.
Table 29--Hayden Smelter Option 1: Visibility Impact and Improvement
From SO2 Controls
------------------------------------------------------------------------
Visibility
Visibility improvement
Class I area Distance impact base new acid
(km) case (base) plant
(ctrl2)
------------------------------------------------------------------------
Chiricahua NM.................. 170 1.05 0.89
Chiricahua WA.................. 174 1.01 0.87
Galiuro WA..................... 48 1.73 1.45
Gila WA........................ 186 0.69 0.60
Mazatzal WA.................... 121 0.88 0.75
Mount Baldy WA................. 151 0.66 0.56
Petrified Forest NP............ 215 0.70 0.61
Pine Mountain WA............... 168 0.67 0.57
Saguaro NP..................... 82 1.38 1.18
Sierra Ancha WA................ 84 1.09 0.93
Superstition WA................ 50 1.74 1.47
Sycamore Canyon WA............. 239 0.51 0.44
Cumulative (sum)............... ........... 12.10 10.32
Maximum........................ ........... 1.74 1.47
CIAs >= 0.5 dv....... ........... 12 11
Million $/dv (cumul. dv)....... ........... ............ $1.7
Million $/dv (max. dv)......... ........... ............ $12.1
------------------------------------------------------------------------
[[Page 9345]]
c. Option 2: Wet Scrubber on Existing Stack for Secondary Capture
Cost of Compliance: EPA determined that the annual cost of using a
wet scrubber to control SO2 emissions from the secondary
capture system is $972 per ton of SO2 removed as displayed
in Table 30. We calculated the costs of constructing and operating a
wet scrubber based on information provided in ASARCO's letter \103\
from which we used the highest operating cost estimates to demonstrate
cost-effectiveness. We also included a sludge hauling fee of $60 per
ton and assumed one ton of SO2 controlled would result in
five tons of sludge. According to ASARCO, these costs do not include
the cost of a booster fan or a modified stack that may be needed,
thereby somewhat increasing the cost over what is shown here. Although
the calculation includes the cost of hauling sludge off site, it does
not include the cost of treating or landfilling the sludge.
---------------------------------------------------------------------------
\103\ Letter from Jack Garrity, ASARCO to Thomas Webb, EPA (July
11, 2013).
Table 30--Hayden Smelter Option 2: Wet Scrubber on Existing Stack
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual variable Total annual Tons SO2 Control $/ton SO2
Capital cost capital cost cost cost reduced efficiency removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$28,000,000....................................... $2,643,002 $14,186,965 $16,829,967 17,290 85% $972
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: Operation of a
wet scrubber would likely require operation of a booster fan and a gas
re-heater to force emissions through the 305 meter stack. The addition
of a wet scrubber could result in a detached visible plume as water
vapor emitted from the scrubber condenses. Addition of a scrubber would
result in sludge which would have to be shipped off site to be treated
or landfilled. Because of metals in the sludge, it may need to be
treated as hazardous waste.
Pollution Control Equipment in Use at the Source: This is the same
as for Option 1.
Remaining Useful Life of the Source: This is the same as for Option
1.
Degree of Visibility Improvement: We did not conduct visibility
modeling for this option. Because a scrubber is less efficient at
removing SO2 than a second acid plant, the emission rates
would be higher and there would be less visibility improvement from a
scrubber compared to an acid plant. Given that scrubbers are less cost-
effective than a second acid plant, we deemed it unnecessary to model
impacts.
d. Option 3: Wet Scrubber on Acid Tail Stack for Primary Capture
Cost of Compliance: EPA determined the annual cost of using a wet
scrubber to control SO2 emissions from the existing acid
plant tail stack is $13,564 per ton of SO2 removed as
displayed in Table 31. We calculated the costs of constructing and
operating a wet scrubber based on information provided by ASARCO.\104\
In this case, we used the low-end estimate of operating costs because
we are demonstrating that this option is not cost-effective. We also
included a sludge hauling fee of $60 per ton and assumed one ton of
SO2 controlled would result in five tons of sludge. Again,
these costs did not include the cost of a booster fan or a modified
stack that may be needed. Although the calculation included the cost of
hauling sludge off site, it did not include the cost of treating or
disposing the sludge, which may be classified as hazardous waste
depending on the metals content. In addition, we note that some of the
SO2 that passes through the acid plant is emitted by the
flash furnace that is not BART-eligible.
---------------------------------------------------------------------------
\104\ Ibid.
Table 31--Hayden Smelter Option 3: Wet Scrubber on Acid Tail Stack
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual variable Total annual Control Tons SO2 $/ton SO2
Capital cost capital cost cost cost efficiency reduced removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$28,000,000....................................... $2,643,002 $9,274,521 $11,917,523 85% 879 $13,564
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: This is the same
as for Option 2.
Pollution Control Equipment in Use at the Source: This is the same
as for Options 1 and 2.
Remaining Useful Life of the Source: This is the same as for
Options 1 and 2.
Degree of Visibility Improvement: We did not conduct visibility
modeling for a tail stack scrubber because of the high control cost per
ton of SO2. However, because the scrubber would remove much
less SO2 than options 1 or 2 (second acid plant and wet
scrubber on the secondary capture, respectively), the expected
visibility improvement is far less than for options 1 and 2.
e. Proposed BART Determination for SO2 From Converters
Based on the results of our BART analysis, we propose that BART for
SO2 from the converters is a level of control consistent
with what ASARCO could achieve through the installation of a new double
contact acid plant. This would control about 20,341 tpy of
SO2 emissions from the converter units at a cost of about
$872 per ton of SO2 removed, which we consider highly cost-
effective. The expected visibility benefits of this option are
substantial with a greater than 0.5 dv improvement in eleven Class I
areas with a maximum benefit of 1.47 dv at Superstition WA. We propose
to find that the energy and non-air quality environmental effects of
this option are not sufficient to warrant elimination of this option.
Regarding the other options, a wet scrubber for the secondary
capture (Option 2) is less effective at a similar annual cost but with
greater non-air environmental impacts. Therefore, we do not propose to
require this as BART. Adding a scrubber to the existing acid tail stack
for the primary capture (Option 3) would result in a relatively small
amount of additional emissions reductions at a relatively high cost
($13,564 per ton of SO2 removed) and with potentially
significant non-air environmental impacts. Therefore, we propose that
the addition of a scrubber
[[Page 9346]]
to the existing acid plant is not required as BART.
The specifics of our BART proposal for SO2 from the
converters are as follows:
An SO2 control efficiency of 99.8 percent, 30-
day rolling average, on all SO2 captured by the primary and
secondary control systems. The control efficiency may be averaged
between the two capture systems on a mass basis, if needed. (For every
30-day period the total mass of SO2 exiting the two control
systems must be no greater than 0.0019 percent of the SO2
entering the control systems.)
Compliance with the SO2 BART limit may be
verified either through the use of SO2 CEMS before and after
controls in each system or by using post-control CEMS and acid
production rates. A limit of 2.49 lbs SO2 emissions per tons
of sulfuric acid production is equivalent to 99.8 percent control.
Operation and maintenance of primary and secondary capture
systems meeting the requirements of 40 CFR part 63, subpart QQQ.
We propose to require that these requirements be met within 3 years
of promulgation of the final rule, consistent with the requirement of
the CAA and the RHR that BART be installed ``as expeditiously as
practicable.''
2. BART Analysis and Determination for SO2 From Anode
Furnaces
a. BART Analysis for SO2 From Anode Furnaces
We identified the same two control technologies for the anode
furnaces: a new double contact acid plant and a wet scrubber. In
addition, we considered whether emissions from the anode furnaces might
be vented to the existing acid plant.
Cost of Compliance: Based on our calculations, we estimated that
the cost to control 37 tpy of SO2 from the anode furnaces by
construction of a new acid plant is over $28,000 per ton, not including
the cost of inlet preheating,\105\ as shown in Table 32. The estimated
cost of installing and operating a wet scrubber is even more expensive
at over $80,000 per ton\106\ as shown in Table 33.
---------------------------------------------------------------------------
\105\ See the TSD for further discussion of this issue.
\106\ See the TSD, Section III.D.4.
Table 32--Hayden Smelter: New Acid Plant for the Anode Furnaces
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual Total annual Tons SO2 Control $/ton SO2
Capital cost capital cost variable cost cost reduced efficiency removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$8,583,190........................................ $810,192 $261,827 $1,071,920 37 99.8% $28,616
--------------------------------------------------------------------------------------------------------------------------------------------------------
Table 33--Hayden Smelter: New Wet Scrubber for the Anode Furnaces
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual Total annual Tons SO2 Control $/ton SO2
Capital cost capital cost variable cost cost reduced efficiency removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$7,000,000........................................ $660,750 $2,009,570 $2,670,320 32 85% $83,708
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: This is the same
as for the converters.
Pollution Control Equipment in Use at the Source: The anode
furnaces currently have no SO2 controls in place.
Remaining Useful Life of the Source: ASARCO has not indicated that
any of the anode furnaces would need to be replaced during the 20-year
capital cost recovery period.
Degree of Visibility Improvement: We did not conduct visibility
modeling for the anode furnace emissions. However, since the emissions
from these units are a small fraction of those from the converters, the
expected visibility improvement would be far less than for any of the
controls considered for the converters.
b. Proposed BART Determination for SO2 From Anode Furnaces
Given the high cost of control, and the small potential for
visibility improvement, we propose that controlling the 37 tpy of
SO2 emissions from the anode furnaces is not warranted as
BART. Furthermore, while redirecting the anode furnace emissions to the
existing acid plant might be technically feasible and cost-effective,
the emission reductions and visibility benefit, although not
calculated, would be much smaller than the calculated benefits from
controlling additional emissions from the converters.
In order to ensure that emissions from anode furnaces do not
increase substantially in the future, we are proposing to establish a
work practice standard for these units. While BART determinations are
generally promulgated in the form of numeric emission limitations, the
RHR allows for use of equipment requirements or work practice standards
in lieu of a numeric limit where ``technological or economic
limitations on the applicability of measurement methodology to a
particular source would make the imposition of an emission standard
infeasible.''\107\ In this case, we find that a numerical emission
limitation for the anode furnaces would be infeasible because of the
relatively small amount of emissions from these units, compared with
the converters. Therefore, we are proposing to establish a work
practice standard in the form of a requirement that the anode furnaces
be charged with blister copper or higher purity copper. Because blister
copper is generally 98 to 99 percent pure copper, this requirement will
ensure that sulfur emission from the anode furnaces are minimized.
---------------------------------------------------------------------------
\107\ 40 CFR 51.308(e)(1)(iii). See also 40 CFR 51.100(z)
(defining ``emission limitation'' and ``emission standard'' to
include ``any requirements which . . . prescribe equipment . . . for
a source to assure continuous emission reduction.''
---------------------------------------------------------------------------
3. Subject-to-BART, BART Analysis and BART Determination for
NOX
a. Proposed Subject-to-BART Finding for NOX
As explained in our final rule on the Arizona RH SIP, once a source
is determined to be subject to BART, the RHR allows for the exemption
of a specific pollutant from a BART analysis only if the potential to
emit for that pollutant is below a specified de minimis level.\108\
Neither the Hayden Smelter's current Title V permit nor the Arizona RH
SIP contains any physical or operational limitations that would limit
the PTE of the BART-eligible
[[Page 9347]]
source below the NOX de minimis threshold of 40 tpy.
Therefore, because the Hayden Smelter is subject to BART and has a PTE
of more than 40 tons per year of NOX, we have analyzed
potential NOX BART controls for the source.
---------------------------------------------------------------------------
\108\ 40 CFR 51.308(e)(1)(ii)(C).
---------------------------------------------------------------------------
b. BART Analysis for NOX
The Hayden Smelter's NOX emissions result from the
combustion of natural gas to heat process equipment. LNB are an
available, feasible and effective technical option for such process
heaters, with an estimated control efficiency of 50 percent.\109\
---------------------------------------------------------------------------
\109\ AirControlNet, Version 4.1, documentation report by E.H.
Pechan and Associates, Inc. for U.S. EPA, Office of Air Quality,
Planning, and Standards, May 2006, section III, page 445.
---------------------------------------------------------------------------
Cost of Compliance: According to the Documentation Report
accompanying AirControlNet, the cost to retrofit process heaters with
LNB is $2,200 per ton.\110\
---------------------------------------------------------------------------
\110\ Id.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: No significant
energy and non-air environmental impacts are expected to result from
use of LNB.
Pollution Control Equipment in Use at the Source: No NOX
controls are currently employed at either the converters or the anode
furnaces.
Remaining Useful Life of the Source: ASARCO has not indicated that
any of the units would need to be replaced during the 20-year capital
cost recovery period.
Degree of Visibility Improvement: The maximum modeled 98th
percentile visibility impact resulting from baseline NOX
emissions from the Hayden Smelter is no higher than 0.01 dv\111\ at any
of the Class I areas. Thus, the maximum visibility benefit of controls
is less than 0.01 dv.
---------------------------------------------------------------------------
\111\ Summary of WRAP RMC BART Modeling for Arizona, Draft
Number 5, May 25, 2007. Also, ASARCO response letter, July 11, 2013,
ENVIRON memo attachment, March 4, 2012, (``H-09 2013-03-04 ENVIRON
report-Asarco-Hayden-BART.pdf''.
---------------------------------------------------------------------------
c. Proposed BART Determination for NOX
Given the small potential for visibility improvement, we propose
that controlling these NOX emissions is not warranted for
purposes of BART. However, in order to ensure that NOX
emissions do not increase in the future, we propose to set a 12-month
rolling limit of 40 tons of NOX from the subject-to-BART
units, which is equivalent to the de minimis level of emissions set out
in the RHR.\112\ This emission limit is slightly lower than the annual
50 tpy baseline emissions noted above. Nonetheless, we consider it to
be a reasonable limit because the 50 tpy estimate assumes that all of
the converters are all operating simultaneously, which is not how they
typically operate. Therefore, we expect actual emissions to be well
below 40 tpy, which is consistent with ASARCO's own estimate.\113\
---------------------------------------------------------------------------
\112\ 40 CFR 51.308(e)(1)(ii)(C).
\113\ Letter from Krishna Parameswaran, ASARCO, to Gregory Nudd,
EPA dated March 6, 2013, page 15.
---------------------------------------------------------------------------
4. Summary of EPA's Proposed BART Determinations
We propose that BART for SO2 from the converters is a
control efficiency of 99.8 percent, 30-day rolling average, on all
SO2 captured by the primary and secondary control systems.
We propose to require compliance with this requirement within three
years of promulgation of a final rule. We also are proposing
monitoring, recordkeeping and reporting as well as operation and
maintenance requirements, to ensure the enforceability of our proposed
BART determination. We propose a work practice standard consistent with
current practices for the anode furnaces. We also propose to set a 12-
month rolling limit of 40 tons of NOX from the subject-to-
BART units.
We are seeking comment on all aspects of this proposal. In
particular, we are seeking comment on the following elements of our
BART analysis and determination for SO2 from the converters:
The cost of controls;
the collection efficiency for the primary collection
system;
the collection efficiency for the secondary collection
system;
the control efficiency to be applied to the primary and
secondary collections systems;
the compliance methodology; and
the compliance schedule.
If we receive additional information concerning these or other elements
of our analysis, we may finalize a BART determination that differs in
some respects from this proposal.
D. Miami Smelter
Summary: EPA proposes to find that the Miami Smelter is subject to
BART for NOX in addition to SO2 and
PM10, as determined by the State. For SO2 from
the converters, we propose to require construction of a secondary
capture system consistent with the requirements of MACT QQQ and an
SO2 control efficiency of 99.7 percent, 30-day rolling
average, on all SO2 captured by the primary and secondary
capture systems. For SO2 emissions from the electric
furnace, we propose to prohibit active aeration of the electric
furnace. For NOX, we propose to find that controlling
emissions from the converters and anode furnaces is cost-effective, but
would not result in sufficient visibility improvement to warrant the
cost. Therefore, we are proposing an annual emission limit of 40 tpy
NOX emissions from the BART-eligible units at the Miami
Smelter, which is consistent with current emissions from these units.
We previously approved Arizona's determination that BART for
PM10 at the Miami Smelter is the NESHAP for Primary Copper
Smelting. Please refer to the Long Term Strategy in Section VII below,
regarding our proposal to ensure the enforceability of this
determination.
Affected Class I Areas: Twelve Class I areas are within 300 km of
the Miami Smelter with the nearest borders ranging from 55 km to 260 km
away. The set of areas differs from the ones near the Hayden Smelter
only in that Bosque Del Apache WA is included, and Sycamore Canyon WA
is not. The baseline visibility impacts are 0.70 dv or less at all
Class I areas except at Superstition where the visibility impact is 3.6
dv. The cumulative sum of visibility impacts at all areas within 300 km
is 8.2 dv.
Facility Overview: The Miami Smelter is a batch-process copper
smelter in Gila County, Arizona. We previously approved ADEQ's
determination that Hoboken Converters 2, 3, 4 and 5 and the Electric
Furnace at the facility are BART-eligible.\114\ We also approved ADEQ's
determination that these units are subject to BART for SO2
and that BART for PM10 at the Miami Smelter is the Maximum
Achievable Control Technology (MACT) Subpart QQQ under the National
Emission Standards for Hazardous Air Pollutants (NESHAP) for primary
copper smelting. However, we disapproved ADEQ's determination that
existing controls constitute BART for SO2 and that the units
are not subject to BART for NOX. In light of these
disapprovals and our FIP duty for Regional Haze in Arizona, we are
required to promulgate a FIP to address BART for both SO2
and NOX.
---------------------------------------------------------------------------
\114\ 78 FR 46412 (July 30, 2013). See also the TSD for a
description of these units.
---------------------------------------------------------------------------
Baseline Emissions: Because neither FMMI nor ADEQ identified
baseline emissions for the Miami Smelter, we selected emissions from
2010 as the baseline. We chose 2010 because ADEQ provided the most
detailed emissions information from this year in its RH SIP and because
FMMI used 2010 as a basis for calculating uncaptured emissions of
SO2 for 2011 and 2012. FMMI reports
[[Page 9348]]
emissions of SO2 to ADEQ by stack, and performs a mass-
balance equation to determine uncaptured emissions. SO2
emissions in tons per year are presented in Table 34 as reported by
FMMI to ADEQ for the acid plant duct, acid plant bypass duct, and the
vent fume duct.\115\ Because each of these stacks vents emissions from
both BART and non-BART emission units, EPA apportioned the emissions to
BART and non-BART units for purposes of our analysis. The BART-eligible
emissions from the acid plant were based on FMMI and ADEQ's estimate
that 35 percent of SO2 sent to the acid plant is emitted by
the converters and 65 percent of SO2 is emitted by the
primary smelter (often called by a proprietary name, the IsaSmelt
furnace) and electric furnace. Because it is not possible to
differentiate which converter emissions are from the one converter that
is not BART-eligible, we are treating all converter emissions as
subject to BART. Subject-to-BART emissions from the vent fume duct were
set at seven tons per year based on our estimate of the share of
emissions originating from the electric furnace. Please refer to the
TSD for an explanation for how the subject-to-BART uncaptured emissions
are determined.
---------------------------------------------------------------------------
\115\ The vent fume duct is the stack for a wet scrubber used to
control emissions collected by the IsaSmelt secondary collection
system, other collection systems associated with conveyors that are
not BART-eligible, and emissions collected by the BART-eligible
electric furnace secondary collection system.
Table 34--Miami Smelter: BART Baseline Emissions for SO2 in 2010
[Tons per year]
----------------------------------------------------------------------------------------------------------------
Acid plant Acid plant
duct bypass Vent fume duct Uncaptured
----------------------------------------------------------------------------------------------------------------
Total SO2 Emissions............................. 1,415 93 331 8,472
Subject-to-BART SO2 Emissions................... 495 33 7 3,231-8,078
----------------------------------------------------------------------------------------------------------------
FMMI also reports potentially BART-eligible NOX
emissions from the acid plant duct and from ``natural gas combustion''
to ADEQ as depicted in Table 35. FMMI estimates that 15 percent of
NOX emitted from the acid plant duct originates from the
BART-eligible converters. While ``natural gas emissions'' includes
emissions from the converter burners, it is not possible to separate
the BART-eligible emissions from ineligible emissions. Thus, we are
assuming that all these emissions are BART-eligible.
Table 35--Miami Smelter: BART Baseline Emissions for NOX in 2010
[Tons per year]
------------------------------------------------------------------------
Acid plant Natural gas
duct combustion
------------------------------------------------------------------------
Total NOx Emissions..................... 154 15
Subject-to-BART NOX Emissions........... 23 15
------------------------------------------------------------------------
Modeling Overview: Using the CALPUFF model, EPA estimated the
visibility impacts of the Miami Smelter in its current (i.e., baseline)
configuration, and with two different control options for
SO2 emissions. Model inputs were developed using work by the
WRAP and updated stack and other information from FMMI. EPA made two
different emissions calculations, incorporating high and low estimates
of the amount of emissions that are not captured by the existing
systems. Most of the discussion below focuses on modeling performed
using the high estimate as shown in Table 37.
An additional complication for this facility is that most of the
emissions occur via a ``roofline,'' a long rectangular hole in the roof
of the building containing the converters. Modeling the roofline as if
it were a stack may be problematic, especially for nearby Class I
areas. Modeling the roofline as a buoyant line source is a better
characterization of the source. EPA performed sensitivity simulations,
described in the TSD, and found that impacts do vary depending on
whether it is modeled as a stack or a line source. Which modeling
scenario resulted in higher impacts depended on the particular Class I
area. EPA therefore modeled the main emissions from FMMI as a buoyant
line source, despite the considerably longer model run times.
1. BART Analysis for SO2 From Converters
a. Control Technology Availability, Technical Feasibility and
Effectiveness
We identified two available and feasible technologies to control
SO2 emissions from the converters: a double contact acid
plant and wet scrubbing. FMMI already uses these two technologies in
series to control SO2 emissions currently captured from the
converters. Based on SO2 acid plant emissions and sulfuric
acid production data provided to EPA by FMMI, we calculated that the
existing acid plant and tail gas scrubber system is controlling at
least 99.7 percent of the SO2 ducted to the acid plant,\116\
which we consider effective. Because FMMI already uses both of the two
available control technologies to control SO2 emissions
currently captured from the converters and achieves a high degree of
control of these emissions, we did not further evaluate additional
controls or upgrades to the existing controls as BART. Rather, we
evaluated ways to improve the capture efficiency of the existing system
so that additional emissions may be collected and controlled.
---------------------------------------------------------------------------
\116\ Letter from Derek Cooke, FMMI, to Thomas Webb, EPA,
Appendices A and C, January 25, 2013.
---------------------------------------------------------------------------
In order to analyze options for improved capture, we requested
information from FMMI regarding potential design improvements, upgrades
to existing equipment or new equipment that could increase the degree
of capture of SO2 emissions from the converters.\117\ In
response, FMMI reported that it planned to improve the
[[Page 9349]]
converter mouth covers, reconfigure the roofline capture system and
route the captured emissions to the existing acid plant.\118\
Accordingly, we performed a five-factor BART analysis for these
improvements, which we refer to collectively as a ``secondary capture
system.''
---------------------------------------------------------------------------
\117\ Letter from Thomas Webb, EPA, to Derek Cooke, FMMI (June
27, 2013).
\118\ Letter from Derek Cooke, FMMI to Thomas Webb, EPA, Item 2
(July 12, 2013). FMMI indicated that ``[t]hese proposed changes are
in anticipation of measures that may be adopted by ADEQ as necessary
to demonstrate compliance'' with the 2012 SO2 NAAQS.''
Regardless of their regulatory purpose of the changes, FMMI's
proposal indicates that these changes are technically feasible.
---------------------------------------------------------------------------
b. Secondary Capture System
The purpose of the secondary capture system is to improve capture
and control of SO2 emissions from the converters that can
then be directed to the existing double contact acid plant.
Cost of Compliance: FMMI claimed as confidential business
information (CBI) the cost information for improvements in
SO2 capture, so we relied on other information to estimate
the cost of controls. In particular, we considered cost estimates
supplied by ASARCO for the Hayden Smelter, a similar facility, for a
series of upgrades to its capture systems.\119\ We estimated cost-
effectiveness using a capital cost of $47,850,000, and annualized those
costs assuming a 20-year lifespan and a 7 percent interest rate with an
operation and maintenance cost of 50 percent of the capital cost. We
applied a control efficiency of 99.7 percent, which the existing acid
plant and tail stack scrubber system currently achieves using very
limited cesium catalyst. The emission reduction was applied to 85
percent of the currently uncaptured SO2 emissions from the
converters.\120\ Based on these calculations, we estimate the cost-
effectiveness of installing and operating a secondary capture system
would be $990 to $2,474 per ton of SO2 removed, as shown in
Table 36. This range reflects the uncertainty in the quantity of
SO2 emissions that are currently not captured.
---------------------------------------------------------------------------
\119\ See the TSD, Section III.D.4.
\120\ Review of New Source Performance Standards for Primary
Copper Smelters, OAQPS, EPA 450/3-83-018a, March 1984. According to
Section 4.7.6.3, the overall collection efficiency of secondary
fixed hoods is approximately 90 percent.
Table 36--Miami Smelter: Cost of Secondary Capture of SO2 From Converters
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual Total annual Tons SO2 Control $/ton SO2
Capital cost capital cost variable cost cost reduced efficiency removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$47,850,000....................................... $4,516,701 $2,258,351 $6,775,052 2,379-6,845 99.7% $990-2,474
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: We do not
anticipate significant energy or other non-air quality environmental
impacts resulting from capturing and ducting additional emissions to
the existing SO2 control system given that FMMI already has
the capacity to handle and store the much larger quantities of sulfuric
acid produced by emissions captured from the IsaSmelt and converter
primary capture systems.
Pollution Control Equipment in Use at the Source: SO2
emissions collected from the converters are ducted to the four-pass,
double contact acid plant. There is a wet scrubber (the tailstack
scrubber) located after the acid plant outlet, to which emissions may
be vented during periods of elevated SO2
concentrations.\121\
---------------------------------------------------------------------------
\121\ Letter from Derek Cooke, FMMI to Thomas Webb, EPA, Item 2
(July 12, 2013).
---------------------------------------------------------------------------
Remaining Useful Life: The BART-eligible converters have each been
in place for about 40 years. FMMI has not indicated that any of them
would be replaced during the 20-year capital cost recovery period.
Degree of Visibility Improvement: As shown in Table 37, installing
a secondary capture system to collect and direct SO2
emissions from the converters to the acid plant, the maximum 98th
percentile baseline improvement ranges from a low of 0.41 dv to a high
of 1.06 dv at Superstition WA. The cumulative improvement ranges from
1.7 to 4.3 dv. These are large visibility improvements that support
using the existing acid plant with a new secondary capture system as
BART for SO2. The high and low visibility impacts and
improvements in Table 37 correspond to the range of emissions that are
not captured. The range is 3,231 (low) to 8,078 (high) tpy. For the low
emission estimate, the maximum improvement from the secondary capture
system is 0.41 dv, and the cumulative improvement is 1.7 dv. These are
considerably less than for the high emission estimate, which has a
maximum improvement of 1.06 dv and cumulative improvement of 4.3 dv,
but is still substantial.
Table 37--Miami Smelter: Visibility Impact and Improvement From Secondary Capture System
----------------------------------------------------------------------------------------------------------------
Impact Improvement Impact Improvement
-------------- from control -------------- from control
Distance -------------- -------------
Class I area (km) High base Converter Low base Converter
case 85% capture case 85% capture
(basehi) (opt1hi) (baselo) (opt1lo)
----------------------------------------------------------------------------------------------------------------
Bosque del Apache WA....................... 235 0.15 0.12 0.07 0.05
Chiricahua NM.............................. 113 0.36 0.27 0.16 0.10
Chiricahua WA.............................. 125 0.35 0.27 0.16 0.10
Galiuro WA................................. 99 0.56 0.40 0.28 0.17
Gila WA.................................... 55 0.34 0.26 0.16 0.10
Mazatzal WA................................ 220 0.64 0.44 0.32 0.17
Mount Baldy WA............................. 95 0.27 0.20 0.13 0.08
Petrified Forest NP........................ 197 0.33 0.25 0.16 0.10
Pine Mountain WA........................... 260 0.43 0.32 0.20 0.12
Saguaro NP................................. 143 0.45 0.34 0.21 0.13
Sierra Ancha WA............................ 158 0.70 0.40 0.42 0.17
Superstition WA............................ 163 3.61 1.06 2.86 0.41
[[Page 9350]]
Cumulative (sum)........................... ........... 8.2 4.3 5.1 1.7
Maximum.................................... ........... 3.61 1.06 2.86 0.41
CIAs >= 0.5 dv................... ........... 4 1 1 0
Million $/dv (cumul. dv)................... ........... ............ $1.6 ............ $4.0
Million $/dv (max. dv)..................... ........... ............ $6.4 ............ $16.7
----------------------------------------------------------------------------------------------------------------
c. Proposed BART Determination for SO2 From Converters
Based on the results of our BART analysis, we propose that BART for
SO2 from the converters is construction of a secondary
capture system (i.e., construction of hooding and ventilation systems
to capture escaped SO2 emissions) and ducting the emissions
to existing controls. We have determined that these improvements are
feasible and cost-effective, will result in significant visibility
improvements, and should not result in significant adverse impacts. As
noted above, the RHR allows for use of equipment requirements or work
practice standards in lieu of a numeric limit where ``technological or
economic limitations on the applicability of measurement methodology to
a particular source would make the imposition of an emission standard
infeasible.'' \122\ In this instance, we propose to find that
technological limitations on the source's ability to measure accurately
uncaptured SO2 emissions make numeric capture efficiency
infeasible. Therefore, we are proposing to prescribe specific equipment
for capture of SO2 emissions, in addition to numeric control
efficiency and related compliance requirements. Specifically, we are
proposing the following as BART for SO2 from the converters:
---------------------------------------------------------------------------
\122\ 40 CFR 51.308(e)(1)(iii). See also 40 CFR
51.100(z)(defining ``emission limitation'' and ``emission standard''
to include ``any requirements which . . . prescribe equipment . . .
for a source to assure continuous emission reduction.''
---------------------------------------------------------------------------
Construction of a secondary capture system consistent with
the requirements of MACT QQQ as a work practice standard.
An SO2 control efficiency of 99.7 percent, 30-
day rolling average, on all SO2 captured by the primary and
secondary capture systems.
Compliance with the SO2 BART limit may be
verified either through the use of SO2 CEMS before and after
controls or by using post-control CEMS and acid production rates. A
limit of 4.06 lbs SO2 emissions per tons of sulfuric acid
production is equivalent to 99.7 percent control.
d. Alternative Control Efficiency
We are also seeking comment on whether FMMI should be expected to
meet a 99.8 percent control efficiency, 30-day rolling average, on all
SO2 captured by the primary and secondary capture systems.
ASARCO Hayden has demonstrated that a control efficiency of 99.8
percent is achievable in practice at a batch copper smelter. FMMI could
increase control efficiency by increasing its use of cesium promoted
catalyst in the acid plant, increasing the volume of gas exiting the
acid plant that is further controlled by the tail stack scrubber, and/
or using sodium rather than magnesium in the scrubbing liquor. If we
received comments establishing that a control efficiency greater than
99.7 percent is achievable at FMMI, we may finalize a control
efficiency of up to 99.8 percent.
2. BART Analysis for SO2 From Electric Furnace
a. Control Technology Availability, Technical Feasibility and
Effectiveness
EPA identified two possible technologies to control SO2
emissions from the electric furnace: Double contact acid plant and wet
scrubbing. FMMI has indicated to EPA that emissions from the electric
furnace are already controlled by the existing double contact acid
plant and tail stack scrubber.\123\ In addition, a secondary capture
system ducts gases not captured by the primary capture system to the
vent fume scrubber, which has a control efficiency of 80 percent.
Because FMMI already uses both of the two available control
technologies to control SO2 emissions currently captured
from the furnace, we did not evaluate the addition of new controls, nor
did we evaluate upgrades to the acid plant system, which already
achieves a high degree of control. The one improvement to controls that
we identified was upgrading the scrubber, which currently uses
magnesium oxide, to use sodium hydroxide, which could increase the
control efficiency from 80 percent to 98 percent.
---------------------------------------------------------------------------
\123\ ADEQ Class 1 Permit Number 53592, Application for a
Significant Permit Revision, July, 2013.
---------------------------------------------------------------------------
b. Existing Double Contact Acid Plant and Wet Scrubbing
Cost of Compliance: We estimated the emissions from the electric
furnace by multiplying the relevant AP 42 emission factors for copper
smelters \124\ by the 2010 concentrate throughput provided by FMMI.
This results in uncontrolled emissions of SO2 from the
electric furnace of 379 tons per year. Because the scrubber is a
secondary control device, however, this would likely result in an
emissions decrease of no more than 5 to 10 tons per year. Replacing
magnesium oxide with sodium hydroxide would cost at least $2,000,000
per year, resulting in control costs of $200,000-$400,000 per ton of
SO2 removed, as shown in Table 38.
---------------------------------------------------------------------------
\124\ AP 42, Chapter 12.3, Primary Copper Smelters, Table 12.3-3
(cleaning furnace) and Table 12.3-11 (converter slag return).
[[Page 9351]]
Table 38--Miami Smelter: Cost of Upgrading Vent Fume Scrubber
--------------------------------------------------------------------------------------------------------------------------------------------------------
Annualized Annual Total annual Tons SO2 Control
Capital cost capital cost variable cost cost reduced efficiency $/ton SO2 removed
--------------------------------------------------------------------------------------------------------------------------------------------------------
$2,000,000 $2,000,000 5-10 98% $200,000-$400,000
--------------------------------------------------------------------------------------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts: We do not
anticipate significant energy or non-air quality environmental impacts
resulting from capturing and ducting additional emissions to the
existing SO2 control system. Non-air quality impacts from
venting additional captured emissions to the existing scrubber are not
expected to be significant given that FMMI is already controlling much
larger quantities of SO2 in the existing scrubber and
managing the wastewater and sludge that result.
Pollution Control Equipment in Use at the Source: SO2
emissions collected from the electric furnace are ducted to the four-
pass, double contact acid plant. There is a wet scrubber (the tailstack
scrubber) located after the acid plant outlet, to which emissions may
be vented ``if needed.'' In addition, gases collected from the
secondary collection system are ducted to the vent fume scrubber, which
is another wet scrubber. The vent fume scrubber also controls secondary
emissions from the IsaSmelt and emissions collected from other
equipment.
Remaining Useful Life: FMMI has not indicated any plans to remove
the electric furnace from service.
Degree of Visibility Improvement: Our modeling results did not
demonstrate even modest visibility improvements at any Class I areas
from this option. Improvements were 0.004 dv or less at each Class I
area, and only 0.008 dv for the cumulative sum over all areas. These
are negligible visibility improvements over the baseline levels, as
expected from the small emission reductions associated with this
option.
c. BART Determination for Electric Furnace
Based on the high cost of compliance to upgrade the vent fume
scrubber and low potential for visibility improvement, we are proposing
that existing controls represent BART for SO2 emissions from
the electric furnace. While we would prefer to set a numeric emission
limit in order to ensure that SO2 emissions from the
electric furnace do not increase in the future, such a limit is
impracticable because emissions from the electric furnace are
commingled with emissions from non-BART eligible units in the vent fume
stack. Therefore, consistent with 40 CFR 51.308(e)(1), we propose a
work practice standard prohibiting active aeration of the electric
furnace.
3. BART Analysis for NOX From Process Heaters
NOX emissions from the FMMI smelter result from the
combustion of natural gas to heat process equipment. According to the
Documentation Report accompanying AirControlNet, the cost to retrofit
process heaters with low NOX burners, which can reduce
NOX emissions by 50 percent, is $2,200 per ton.\125\
Although this is not necessarily cost-prohibitive, there is relatively
little potential for visibility improvement from installation of any
NOX controls at FMMI. In particular, the maximum modeled
98th percentile visibility impact resulting from baseline
NOX emissions from FMMI is 0.11 dv.\126\ In addition, the
WRAP estimated the annual BART-eligible NOX emissions from
the facility as 159 tons per year,\127\ whereas we estimate annual
BART-eligible NOX baseline emissions as 38 tons per year.
Therefore, the baseline visibility impact attributable to
NOX, and thus, the potential for visibility improvement due
to NOX reductions, is, in fact, significantly less than 0.11
dv. Given the small potential for visibility improvement, we propose
that NOX controls are not warranted for purposes of BART.
However, in order to ensure that NOX emissions do not
increase in the future, we propose to set a 12-month rolling cap of 40
tons of NOX from the subject-to-BART units, which is
equivalent to the de minimis level of emissions set out in the RHR and
is roughly equivalent to current annual emissions from these
units.\128\
---------------------------------------------------------------------------
\125\ AirControlNet, Version 4.1, Documentation Report. Prepared
by E.H. Pechan and Associates, Inc. for U.S. EPA, Office of Air
Quality, Planning, and Standards. May, 2006, section III, page 445.
\126\ Summary of WRAP RMC BART Modeling for Arizona, Draft
Number 5, May 25, 2007, page 23.
\127\ Id.
\128\ 40 CFR 51.308(e)(1)(ii)(C).
---------------------------------------------------------------------------
VI. EPA's Proposed Reasonable Progress Analyses and Determinations
Summary: In this section, EPA addresses point sources for
NOX, area sources for NOX and SO2, the
reasonable progress goals for the Class I areas, and a demonstration
that the rate of progress is reasonable compared to the URP. In our
previous actions on the Arizona RH SIP, EPA narrowed the focus of the
RP analysis to point sources of NOX and area sources of
NOX and SO2. Based on our analysis, we propose to
require emissions reductions consistent with SNCR on Kiln 4 at the
Phoenix Cement Clarkdale Plant and on Kiln 4 at the CalPortland Cement
Rillito Plant. EPA proposes to find that it is not reasonable to
require additional controls on area sources of NOX and
SO2 at this time. We are also proposing RPGs consistent with
a combination of control measures that include the approved Arizona RH
SIP measures as well as the finalized and proposed Arizona RH FIP
measures. Finally, we propose to find that it is not reasonable for any
of Arizona's Class I areas to meet the URP during this planning period,
and demonstrate that rate of progress is reasonable based on our RP
analysis.
Background: The RHR requires the State, or EPA in the case of a
FIP, to set RPGs by considering four factors: ``the costs of
compliance, the time necessary for compliance, the energy and non-air
quality environmental impacts of compliance, and the remaining useful
life of any potentially affected sources'' (collectively ``the RP
factors'').\129\ The RPGs must provide for an improvement in visibility
on the worst days and ensure no degradation in visibility on the best
days during the planning period. Furthermore, if the projected progress
for the worst days is less than the Uniform Rate of Progress (URP),
then the state or EPA must demonstrate, based on the factors above,
that it is not reasonable to provide for a rate of progress consistent
with the URP.\130\
---------------------------------------------------------------------------
\129\ 40 CFR 51.308(d)(1)(i)(A).
\130\ 40 CFR 51.308(d)(1)(ii).
---------------------------------------------------------------------------
In our final rule on the Arizona RH SIP published on July 30, 2013,
we partially approved and partially disapproved the State's RP
analysis.\131\ In particular, we approved the State's decision to focus
on NOX and SO2 sources and its decision not to
require additional controls on non-BART point sources of SO2
for this planning period. However, we disapproved the State's RPGs for
the worst days and best days, as well as its RP analyses and
determinations for point sources of NOX
[[Page 9352]]
as well as area sources of SO2 and NOX.
Accordingly, we have analyzed these remaining source categories to
determine whether additional controls are reasonable based on an
evaluation of the RP factors.
---------------------------------------------------------------------------
\131\ See 78 FR 46173 (codified at 40 CFR 52.145(g)).
---------------------------------------------------------------------------
A. Reasonable Progress Analysis of Point Sources for NOX
EPA conducted an extensive statewide analysis of NOX
point sources to determine whether cost-effective controls on sources
near Class I areas would contribute to visibility improvements. In this
section, we describe the process to identify and analyze these
potentially affected NOX point sources for reasonable
progress. Of the nine point sources evaluated for reasonable progress,
EPA is proposing to require Phoenix Cement Clarkdale Plant and
CalPortland Cement Rillito Plant to comply with new emissions limits
for NOX based on the analysis presented below and in the TSD
available in the docket. We are seeking comment on our analyses and
proposed determinations for all the identified sources.
1. Identification of NOX Point Sources
To identify point sources in Arizona that potentially affect
visibility in Class I areas, EPA examined the annual emissions data
from the WRAP 2002 planning inventory and identified those sources with
facility-wide actual emissions that exceed 250 tpy of NOX or
SO2. For these sources, we calculated the total actual
emission rate (Q) in tpy of NOX and SO2 and
determined the distance (D) in kilometers of each source to its closest
Class I area.\132\ We employed a contractor to prepare an initial
spreadsheet calculating these Q and D values.\133\ We used a Q divided
by D value of ten as a threshold for further evaluation of RP controls.
We selected this value based on guidance contained in the BART
Guidelines, which state:
---------------------------------------------------------------------------
\132\ The analysis included NOX, SO2, and
particulate matter pollutants because we had not yet approved ADEQ's
determination to focus on NOX and SO2, nor had
we approved its conclusion regarding non-BART SO2 point
sources, at the time this screening analysis was performed.
\133\ ``EP-D-07-102 WA5-12 Task4 Deliverable (AZ-BART-QbyD-
Screening-report)-final.xlsx''.
Based on our analyses, we believe that a State that has
established 0.5 deciviews as a contribution threshold could
reasonably exempt from the BART review process sources that emit
less than 500 tpy of NOX or SO2 (or combined
NOX and SO2), as long as these sources are
located more than 50 kilometers from any Class I area; and sources
that emit less than 1000 tpy of NOX or SO2 (or
combined NOX and SO2) that are located more
than 100 kilometers from any Class I area.\134\
---------------------------------------------------------------------------
\134\ See 40 CFR part 51, app. Y, Sec. III (How to Identify
Sources ``Subject to BART'').
The approach described above corresponds to a Q/D threshold of ten. In
addition, the use of a Q/D threshold of ten or greater is recommended
by the Federal Land Managers' Air Quality Related Values Work Group
(FLAG) as a screening threshold, as described in the FLAG 2010 Phase I
Report.\135\ A summary of sources with a Q/D value greater than 10 is
included in Table 39.
---------------------------------------------------------------------------
\135\ Section 3.2, Initial Screening Criteria (New), Federal
Land Managers' Air Quality Related Values Work Group (FLAG) Phase I
Report--Revised (2010).
Table 39--Sources of NOX With Q/D Value Greater Than 10
----------------------------------------------------------------------------------------------------------------
Owner/operator Facility name Q (tpy) D (km) Q/D
----------------------------------------------------------------------------------------------------------------
Arizona Public Service.................. West Phoenix Plant............. 992 73.10 14
CalPortland Cement Co................... Rillito Plant.................. 5,075 6.99 726
Arizona Electric Power Coop............. Apache Generating Station...... 11,840 44.86 264
Arizona Public Service.................. Cholla Power Plant............. 33,588 31.75 1058
Lhoist North America.................... Douglas Lime Plant............. 755 55.16 14
El Paso Natural Gas Co.................. Tucson Compressor Station...... 336 14.72 23
El Paso Natural Gas Co.................. Flagstaff Compressor Station... 1,010 34.94 29
Tucson Electric Power................... Sundt Generating Station....... 5,659 15.84 357
Lhoist North America.................... Nelson Lime Plant.............. 2,556 24.56 104
Freeport-McMoRan........................ Miami Smelter.................. 5,996 15.58 385
Phoenix Cement.......................... Clarkdale Plant................ 2,744 12.65 217
Pima County............................. Ina Road Sewage Plant.......... 258 12.56 21
ASARCO.................................. Smelter and Mill............... 18,486 47.22 392
Salt River Project...................... Coronado Generating Station.... 29,674 48.53 611
Salt River Project...................... San Tan Generating Station..... 335 28.13 12
Catalyst Paper Abitibi.................. Snowflake Pulp Mill............ 5,143 39.36 131
Salt River Project...................... Aqua Fria Generating Station... 994 68.87 14
Tucson Electric Power................... Springerville Generating 32,434 60.46 536
Station.
El Paso Natural Gas Co.................. Williams Compressor Station.... 1,373 19.12 72
----------------------------------------------------------------------------------------------------------------
Of the sources listed in Table 39, we eliminated several sources
from further consideration by calculating updated Q/D values based on
2008-2010 emission data.\136\ As a result, APS West Phoenix Plant,
Lhoist Douglas Plant, SRP San Tan Generating Station, and SRP Agua Fria
Generating Station have Q/D values less than or equal to ten. Thus, we
eliminated these sources from further consideration for this planning
period. However, if any of these sources resume operations at levels
sufficient to increase their Q/D value to ten or greater, Arizona
should consider them for potential RP controls in the next planning
period.
---------------------------------------------------------------------------
\136\ See spreadsheet ``10D Screening Update--2008-10 Emission
Data.xlsx'' in the docket.
---------------------------------------------------------------------------
Finally, we eliminated from further consideration those sources (or
units at sources) that were evaluated under BART. These include the
Apache Generating Station, Coronado Generating Station, Cholla Power
Plant (except Unit 1), Sundt Generating Station (except for Units 1-3),
Snowflake Pulp and Paper Mill, and Nelson Lime Plant. Because the BART
analysis examines many of the same factors as those evaluated for
reasonable progress, we propose that the BART determinations for these
facilities satisfy the requirement for reasonable progress from these
facilities during this planning period. The final list of sources
considered for reasonable progress NOX controls is
summarized in Table 40.
[[Page 9353]]
Table 40--Sources of NOX for Reasonable Progress Analyses
----------------------------------------------------------------------------------------------------------------
Owner/operator Facility name Notes
----------------------------------------------------------------------------------------------------------------
CalPortland Cement Co................ Rillito Plant................
Arizona Public Service............... Cholla Power Plant (Unit 1).. Units 2-4 subject to BART.
El Paso Natural Gas Co............... Tucson Compressor Station....
El Paso Natural Gas Co............... Flagstaff Compressor Station.
Tucson Electric Power................ Sundt Generating Station Unit 4 subject to BART.
(Units 1-3).
Phoenix Cement....................... Clarkdale Plant..............
Pima County.......................... Ina Road Sewage Plant........
Tucson Electric Power................ Springerville Generating Units 3-4 have SCR.
Station (Units 1-2).
El Paso Natural Gas Co............... Williams Compressor Station..
----------------------------------------------------------------------------------------------------------------
2. Analysis of Potentially Affected NOX Point Sources
EPA contracted with the University of North Carolina (UNC) and
their subcontractor, Andover Technology Partners (ATP), to perform RP
analyses for the nine sources listed in Table 40. EPA considered the
four RP factors for each of these sources based on the work from UNC.
In addition, for the larger point sources (EGUs and cement kilns), we
conducted CALPUFF modeling to assess the potential visibility benefits
of controls.\137\ These analyses are set out in the TSD and are
summarized in the following sections.
---------------------------------------------------------------------------
\137\ While visibility is not an explicitly listed factor to
consider when determining whether additional controls are
reasonable, the purpose of the four-factor analysis is to determine
what degree of progress toward natural visibility conditions is
reasonable. Therefore, it is appropriate to consider the projected
visibility benefit of the controls when determining if the controls
are needed to make reasonable progress.
---------------------------------------------------------------------------
a. Phoenix Cement Clarkdale Plant Kiln 4
Costs of Compliance: This facility consists of one precalciner
kiln, which currently uses LNB for NOX control. Our estimate
of costs of compliance is based primarily on estimates provided by PCC
in their March 6, 2013 comment letter, with revisions to certain cost
items we considered to be unreasonable or not allowed by EPA's Control
Cost Manual.\138\ As explained in further detail in the TSD, we
estimated a total annual cost for SNCR of approximately $940,000 per
year. SNCR is estimated to reduce emissions at the kiln by 810 tpy at a
cost of $1,142/ton, based on baseline emissions of 1620 tpy and a 50
percent SNCR control efficiency. As explained in the TSD, we are
seeking comment on whether a different SNCR control efficiency is
appropriate for this kiln. If we receive technical information
demonstrating that a different SNCR control efficiency is appropriate
for Kiln 4, we will incorporate this change into our analysis.
---------------------------------------------------------------------------
\138\ Comments submitted on EPA's December 21, 2012 proposed
rulemaking partially approving and disapproving Arizona's Regional
Haze Plan. 77 FR 75704.
---------------------------------------------------------------------------
Time Necessary for Compliance: We expect that SNCR could be
installed in approximately 3 years from the final date of this action.
The Institute of Clean Air Companies estimates that the installation
time for SNCR on industrial sources is 10-13 months.\139\ CPCC
estimates that it would require approximately three years to install
SNCR on their similar technology kiln. Given these two pieces of
information, a 3-year timeframe appears to be reasonable.
---------------------------------------------------------------------------
\139\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: The
installation and operation of SNCR at the plant would require a small
increase in energy usage. The cost of this additional energy usage is
included in the cost analysis. Non-air quality environmental impacts
associated with SNCR include the hazards of transporting and storing
urea or ammonia, especially if anhydrous ammonia is used. However,
since the handling of anhydrous ammonia will involve the development of
a risk management plan (RMP), we consider the associated safety issues
to be manageable as long as established safety procedures are followed.
Therefore, we find that these impacts are not sufficient to warrant
eliminating SNCR as a control option.
Remaining Useful Life: EPA presumes that the kiln would continue
operating for 20 years and fully amortize the cost of controls.
Degree of Improvement in Visibility: There are twelve Class I areas
within 300 km of the Clarkdale Plant. As shown in Table 41, the highest
98th percentile baseline visibility impact of Phoenix Cement is 5.2 dv
at Sycamore. Pine Mountain, Mazatzal, and the Grand Canyon all have
visibility impacts over 0.5 dv, and other areas are at 0.1 dv or less.
The cumulative sum of visibility impacts over all the Class I areas is
7.5 dv. The maximum visibility improvement due to SNCR is 1.9 dv at
Sycamore, 0.3 dv at Pine Mountain, and slightly less at Mazatzal and
the Grand Canyon. The cumulative improvement from SNCR is 3.0 dv.
Table 41--Phoenix Cement Kiln 4: Visibility Impact and Improvement From
NOX Controls
------------------------------------------------------------------------
Visibility Visibility
impact improvement
Class I Area Distance ---------------------------
(km) Base case SNCR -50%
(base) NOX (ctrl2)
------------------------------------------------------------------------
Bryce Canyon NP................ 296 0.09 0.04
Galiuro WA..................... 278 0.03 0.01
Grand Canyon NP................ 133 0.51 0.25
Mazatzal WA.................... 59 0.51 0.24
Mount Baldy WA................. 249 0.05 0.02
Petrified Forest NP............ 200 0.21 0.10
Pine Mountain WA............... 56 0.66 0.32
[[Page 9354]]
Saguaro NP..................... 284 0.03 0.01
Sierra Ancha WA................ 142 0.09 0.04
Superstition WA................ 151 0.10 0.05
Sycamore Canyon WA............. 10 5.15 1.85
Zion NP........................ 272 0.09 0.05
Cumulative (sum)............... ........... 7.5 3.0
Maximum........................ ........... 5.15 1.85
CIAs >= 0.5 dv....... ........... 4 1
Million $/dv (cumul. dv)....... ........... ............ $0.3
Million $/dv (max. dv)......... ........... ............ $0.5
------------------------------------------------------------------------
Phoenix Cement is only 10.5 km away from the Sycamore Canyon
Wilderness. Therefore NOX emitted by the Plant may not be
fully converted to NO2 by the time it reaches Sycamore
Canyon and may not be fully available to form visibility-degrading
particulate nitrate. However, the CALPUFF model assumes 100 percent
conversion. EPA explored this issue by scaling back the visibility
extinction due to NO2 and nitrate to reflect lower NO-to-
NO2 conversion rates, described further in the TSD. As shown
in Table 42, EPA found that visibility impacts and the improvement due
to SNCR decrease along with the percent conversion assumed. However,
the benefit of SNCR is 0.52 dv when NO conversion is reduced to 25
percent. Even for an unrealistically low assumption of 10 percent
(i.e., no conversion of NO to NO2 after the plume leaves the
stack), the benefit of SNCR is 0.25 dv at Sycamore Canyon alone.
Because the other Class I Areas are far enough away for NOX
emitted by the Plant to be fully converted to NO2, the
benefits at the other Class I areas would remain the same.
Table 42--Benefit of SNCR on Phoenix Cement at Sycamore Canyon for Various NO-to-NO2 Conversion Rates
----------------------------------------------------------------------------------------------------------------
NO % Conversion 100% 75% 50% 25% 10%
----------------------------------------------------------------------------------------------------------------
Base case...................................... 5.14 4.19 3.13 1.94 1.17
SNCR........................................... 3.30 2.68 2.07 1.42 0.92
Benefit........................................ 1.85 1.51 1.06 0.52 0.25
----------------------------------------------------------------------------------------------------------------
Proposed RP Determination: Based on our analysis of the four RP
factors, as well as the expected degree visibility improvement, EPA
proposes to require compliance with an emission limit of 2.12 lb/ton on
Kiln 4 based on a 30-day rolling average basis.\140\ We propose to find
that this emissions limit, equivalent to SNCR control, is cost-
effective at $1,142/ton and would result in significant visibility
benefits at Sycamore Canyon Wilderness Area. We are proposing to
require compliance with the 2.12 lb/ton limit by December 31, 2018.
---------------------------------------------------------------------------
\140\ The basis for this specific emission rate is described in
the TSD.
---------------------------------------------------------------------------
We are also soliciting comment on the possibility of establishing
an annual cap on NOX emissions from Kiln 4 in lieu of a lb/
ton emission limit. Such a cap would provide additional flexibility to
PCC by allowing them to comply either by installing controls or by
limiting production. In particular, we are seeking comment on an annual
NOX emission cap for Kiln 4 of 810 tpy established on a
rolling 12-month basis, effective December 31, 2018. If production
remains at current levels, PCC could meet this cap without installing
any additional controls. However, if production increases to pre-2008
levels, we expect that PCC would need to install SNCR on Kiln 4 to
comply with the cap.
b. CalPortland Cement Rillito Plant Kilns 1-4
The facility consists of three long dry kilns (Kilns 1-3) and one
precalciner kiln (Kiln 4). Due to the significant differences between
long dry kilns and precalciner kilns, we have separately analyzed Kilns
1-3 and Kiln 4.
1. Rillito Plant Kilns 1-3
Kilns 1-3 have not operated since 2008 due to economic conditions.
However, CPCC retains the ability to start using these kilns again at
any time. Therefore, we conducted an analysis of the kilns using pre-
2008 emission levels.
[[Page 9355]]
Costs of Compliance: Our estimate of the costs of compliance is
based primarily on estimates provided by CalPortland in its RP
analysis, with revisions to certain cost items we considered to be
unreasonable or not allowed by EPA's Control Cost Manual.\141\ Our
analysis identified SNCR with Mixing Air Technology (MAT) as the most
cost-effective control technology. Installation of SNCR with MAT on
Kilns 1-3 is estimated to reduce emissions at each kiln by 182 tpy at a
cost of $5,603/ton reduced, based on an annualized cost of
approximately $1 million per year and 30-percent control efficiency for
SNCR.\142\
---------------------------------------------------------------------------
\141\ ``Reasonable Progress Analysis for CalPortland Company
Rillito Cement Plant Kiln, prepared by CalPortland Company.''
Submitted to EPA May 9, 2013.
\142\ See TSD for an analysis of all control options and
associated control efficiencies and control costs.
---------------------------------------------------------------------------
Time Necessary for Compliance: CPCC estimates that the time needed
to install the control equipment is about 3 years.
Energy and Non-Air Quality Environmental Impacts of Compliance: The
installation and operation of SNCR at the plant would require a small
increase in energy usage. The cost of this additional energy usage is
included in the cost analysis. Non-air quality environmental impacts
associated with SNCR include the hazards of transporting and storing
urea or ammonia, especially if anhydrous ammonia is used. However,
since the handling of anhydrous ammonia will involve the development of
an RMP, we consider the associated safety issues to be manageable as
long as established safety procedures are followed. Therefore, we find
that these impacts are not sufficient to warrant eliminating SNCR as a
control option.
Remaining Useful Life: The plant's owner intends to shut down all
four kilns and replace them with a new kiln that would be subject to
Best Available Control Technology and a visibility impact
analysis.\143\ This project has been on hold while the economy in
Arizona recovers. As a result, it is unclear whether these kilns will
be in service long enough to fully amortize the cost of controls.
However, because there is no enforceable shutdown date at this time, we
assume that the kilns will remain in service for a 20-year amortization
period.
---------------------------------------------------------------------------
\143\ See Arizona RH SIP supplement, page 32.
---------------------------------------------------------------------------
Degree of Improvement in Visibility: The maximum visibility
improvement due to SNCR on Kilns 1-3 is 0.22 dv at the eastern unit of
Saguaro NP, 0.18 dv at Galiuro WA, and smaller for other areas. The
cumulative visibility improvement is 0.7 dv.
Table 43--CalPortland Cement Kilns 1-3 and Kiln 4: Visibility Impact and Improvement From NOX Controls
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
impact ---------------------------
Class I area Distance -------------- SNCR on
(km) Base case Kilns 1, 2, SNCR on Kiln
(c0) 3 (c22) 4 (c24)
----------------------------------------------------------------------------------------------------------------
Chiricahua NM............................................ 171 0.25 0.05 0.06
Chiricahua WA............................................ 170 0.23 0.05 0.05
Galiuro WA............................................... 73 1.02 0.18 0.19
Gila WA.................................................. 240 0.12 0.02 0.03
Mazatzal WA.............................................. 171 0.13 0.02 0.03
Mount Baldy WA........................................... 223 0.11 0.03 0.03
Petrified Forest NP...................................... 290 0.11 0.02 0.03
Pine Mountain WA......................................... 213 0.11 0.02 0.02
Saguaro NP............................................... 8 1.26 0.22 0.24
Sierra Ancha WA.......................................... 153 0.13 0.02 0.03
Superstition WA.......................................... 108 0.30 0.06 0.06
Sycamore Canyon WA....................................... 287 0.09 0.02 0.02
Cumulative (sum)......................................... ........... 3.9 0.7 0.8
Maximum.................................................. ........... 1.26 0.22 0.24
CIAs >= 0.5 dv................................. ........... 2 0 0
Million $/dv (cumul. dv)................................. ........... ............ $1.5 $1.4
Million $/dv (max. dv)................................... ........... ............ $4.8 $4.6
----------------------------------------------------------------------------------------------------------------
The Saguaro NP results in this table are for the eastern unit of the park only.
Proposed RP Determination: Given the lack of emissions from Kilns
1-3 over the last five years and the relatively high cost of controls
($5,603/ton), EPA proposes to find that requiring controls for these
units is not reasonable at this time.
2. Rillito Plant Kiln 4
Costs of Compliance: Our estimate of the costs of compliance is
based primarily on estimates provided by CalPortland in its RP
analysis, with revisions to certain cost items we considered to be
unreasonable or not allowed by EPA's Control Cost Manual.\144\ Our
analysis identified the addition of SNCR to the existing LNB as the
most cost-effective available control technology. As explained in
further detail in the TSD, we estimated a total annual cost for SNCR of
approximately $1.1 million per year. SNCR is estimated to reduce
emissions by 1,041 tpy at a cost of $1,047/ton reduced, based on
baseline emissions of 2,082 tons per year and a 50 percent SNCR
control-efficiency. As explained in the TSD, we are seeking comment on
whether a different SNCR control efficiency is appropriate for Kiln 4.
If we receive technical information demonstrating that a different SNCR
control efficiency is appropriate for Kiln 4, we will incorporate this
change into our analysis.
---------------------------------------------------------------------------
\144\ ``Reasonable Progress Analysis for CalPortland Company
Rillito Cement Plant Kiln, prepared by CalPortland Company.''
Submitted to EPA May 9, 2013.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: The
installation and operation of SNCR at the plant would require a small
increase in energy usage. The cost of this additional energy usage is
included in the cost analysis. Non-air quality environmental impacts
associated with SNCR include the hazards of
[[Page 9356]]
transporting and storing urea or ammonia, especially if anhydrous
ammonia is used. However, since the handling of anhydrous ammonia will
involve the development of an RMP, we consider the associated safety
issues to be manageable as long as established safety procedures are
followed. Therefore, we find that these impacts are not sufficient to
warrant eliminating SNCR as a control option.
Existing Pollution Control Equipment: Kiln 4 is a precalciner kiln
that currently uses LNB for NOX control.
Remaining Useful Life: The plant's owner intends to shut down all
four kilns and replace them with a new kiln that would be subject to
Best Available Control Technology and a visibility impact
analysis.\145\ This project has been on hold while the economy in
Arizona recovers. As a result, it is unclear whether these kilns will
be in service long enough to fully amortize the cost of controls.
However, because there is no enforceable shutdown date at this time, we
assume that the kilns will remain in service for a 20-year amortization
period.
---------------------------------------------------------------------------
\145\ See Arizona RH SIP supplement, page 32.
---------------------------------------------------------------------------
Degree of Improvement in Visibility: As shown in Table 43, the
maximum visibility improvement due to SNCR on Kiln 4 is 0.24 dv at the
eastern unit of Saguaro NP, 0.19 dv at Galiuro WA, and smaller for
other areas. The cumulative visibility improvement is 0.8 dv. The
cumulative visibility improvement from SNCR on all four kilns would be
about 1.5 dv.
As discussed above in the section covering visibility improvements
for TEP Sundt, EPA remodeled impacts at Saguaro NP to address both the
eastern and western units of the park. The modeled visibility impact at
the western unit of Saguaro, not shown in the table, is 6.04 dv, far
greater than at the eastern unit. The modeled improvement there due to
SNCR is 0.30 dv, still rather modest but 25 percent greater than for
the eastern unit. However, CalPortland is only 7.8 km away from the
western unit, so its emitted NOX may not be fully converted
to NO2 by the time it reaches there, as is assumed in the
CALPUFF model. It thus may not be fully available to form visibility-
degrading particulate nitrate. EPA explored this issue by scaling back
the visibility extinction due to NO2 and nitrate to reflect
lower NO-to-NO2 conversion rates, described further in the
TSD. EPA found that visibility impacts and the improvement due to SNCR
decrease along with the percent conversion assumed, so much so that at
a 25 percent conversion rate, the SNCR benefit was only 0.05 dv.
Therefore, EPA is relying on impacts and improvements for the more
distant eastern unit of Saguaro NP.
Proposed RP Determination: EPA finds that SNCR is cost-effective
for Kiln 4 at $1,047/ton, would not result in undue non-air quality
environmental impacts, and would result in modest visibility benefits
at Saguaro NP and Galiuro WA. Therefore, we propose to determine that
it is reasonable to require SNCR at Kiln 4. In particular, EPA proposes
to require compliance with an emissions limit of 2.67 lb/ton at Kiln 4
based on a 30-day rolling average by December 31, 2018.\146\ We are
also soliciting comment on the possibility of requiring an annual cap
on NOX emissions in lieu of a lb/ton emission limit. In
order to avoid a shift in production from Kiln 4 to Kilns 1-3, we are
proposing that the cap would apply to all four kilns. In particular, we
are seeking comment on an annual NOX emission cap for Kilns
1-4 of 2,082 tpy, established on a rolling 12-month basis. CPCC could
meet this cap either by retaining production at current levels, or by
increasing production and installing SNCR on Kiln 4. We are proposing
to require compliance with this rolling 12-month limit by December 31,
2018.
---------------------------------------------------------------------------
\146\ See TSD for a discussion of how this emission limit was
calculated.
---------------------------------------------------------------------------
c. APS Cholla Unit 1
Costs of Compliance: Unit 1 is a 1,246 MMBtu/hr tangential coal-
fired boiler, which currently employs LNB with separated overfire air
(SOFA) for NOX control. EPA identified two feasible
additional controls: SNCR and SCR. The estimated emission reductions
and costs for these two options are summarized in Tables 44 and 45.
Table 44--Cholla Unit 1: NOX Emission Estimates
----------------------------------------------------------------------------------------------------------------
NOX emissions Emission
------------------------------------------------ reduction
Control option ---------------
(lb/MMBtu) (lb/hr) (tpy) (tpy)
----------------------------------------------------------------------------------------------------------------
Baseline (LNB+OFA).............................. 0.22 274 1,032
SNCR............................................ 0.15 192 723 310
SCR............................................. 0.05 62 235 798
----------------------------------------------------------------------------------------------------------------
Table 45--Cholla Unit 1: NOX Control Cost Estimates
--------------------------------------------------------------------------------------------------------------------------------------------------------
Total capital Annualized Annual O&M Total annual Cost-effectiveness ($/ton)
cost capital cost costs cost -------------------------------
Control option ----------------------------------------------------------------
($) ($) ($) ($) Ave Incr
--------------------------------------------------------------------------------------------------------------------------------------------------------
Baseline (LNB+OFA)
SNCR.................................................... $2,272,000 $241,725 $918,875 $1,160,599 $3,748
SCR..................................................... 26,437,190 2,812,730 1,425,137 4,237,867 5,313 $6,307
--------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 9357]]
Time Necessary for Compliance: Given the estimate from the
Institute of Clean Air Companies\147\ that about a year is required to
install SNCR, and the estimate of three years for installing SNCR on a
cement kiln discussed previously in this notice, EPA estimates that
SNCR could be installed in less than three years. In our previous
Arizona FIP action, EPA estimated that 5 years would be required to
install SCR on coal-fired boilers.\148\ That estimate also holds for
this source.
---------------------------------------------------------------------------
\147\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
\148\ See 77 FR 42834 at 42865 for more details.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: SCR
and SNCR can result in additional ammonia emissions. There is also
increased truck traffic bringing the reagent on site. SCR will also
slightly reduce the efficiency of the plant, resulting in increased
fuel usage.
Remaining Useful Life: EPA assumes that this plant would continue
operating for 20 years and fully amortize the cost of controls.
Degree of Improvement in Visibility: CALPUFF modeling indicates
that installation of SNCR at Unit 1 would provide a 0.10 dv visibility
benefit at the most affected Class I area, Petrified Forest NP, while
installation of SCR would provide a 0.20 dv benefit at the same area as
shown in Table 46. Note that all of these results, including the base
case, assume that SCR has been applied to Units 2, 3 and 4, consistent
with EPA's previous BART determination for those units.
Table 46--Cholla Unit 1: Visibility Impact and Improvement From NOX Controls
----------------------------------------------------------------------------------------------------------------
Visibility Visibility improvement
impact from control
Distance -----------------------------------------
Class I area (km) Base case
(ctrl0/ SNCR on Unit SCR on Unit
ctrl2--r2) 1 (ctrl2-1) 1 (ctrl2-2)
----------------------------------------------------------------------------------------------------------------
Capitol Reef NP.......................................... 300 0.71 0.04 0.09
Galiuro WA............................................... 249 0.30 0.01 0.01
Gila WA.................................................. 222 0.48 0.01 0.01
Grand Canyon NP.......................................... 179 1.14 0.05 0.12
Mazatzal WA.............................................. 128 0.79 0.02 0.04
Mesa Verde NP............................................ 292 0.65 0.03 0.06
Mount Baldy WA........................................... 128 0.71 0.01 0.02
Petrified Forest NP...................................... 39 3.38 0.10 0.20
Pine Mountain WA......................................... 149 0.55 0.01 0.03
Saguaro NP............................................... 300 0.23 0.00 0.00
Sierra Ancha WA.......................................... 126 0.87 0.02 0.06
Superstition WA.......................................... 166 0.81 0.03 0.06
Sycamore Canyon WA....................................... 147 0.76 0.03 0.07
Cumulative (sum)......................................... ........... 11.4 0.3 0.7
Maximum.................................................. ........... 3.38 0.10 0.20
CIAs >= 0.5 dv................................. ........... 10 0 0
Million $/dv (cumul. dv)................................. ........... ............ $3.0 $5.7
Million $/dv (max. dv)................................... ........... ............ $10.3 $21.7
----------------------------------------------------------------------------------------------------------------
Proposed Determination: EPA proposes to determine that it is not
reasonable to require additional controls on this facility at this
time. The costs for both SNCR and SCR are relatively high in light of
the relatively small anticipated visibility benefits of the controls.
However, this decision should be revisited in future planning periods.
d. El Paso Natural Gas Company's Tucson Compressor Station
Costs of Compliance: This site includes seventeen 1,071 hp
compressor engines. EPA's analysis indicates that the most cost-
effective control would be an air/fuel ratio controller that would
reduce emissions by 578 tpy at a cost of $792/ton.\149\
---------------------------------------------------------------------------
\149\ See spreadsheet ``Non EGU--RP--Ch5.xlsx'' in the docket.
---------------------------------------------------------------------------
The site also includes four 370 hp engines. EPA's analysis
indicates that the most cost-effective control would be a three-way
catalyst that would reduce emissions by 96 tons per year at a cost of
$290/ton.
Time Necessary for Compliance: The Institute of Clean Air Companies
estimates that 8 to 14 weeks would be required to install these kinds
of controls.\150\
---------------------------------------------------------------------------
\150\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance:
Both controls may increase fuel usage by reducing the thermal
efficiency of the engines.
Remaining Useful Life: EPA assumes that the engines would continue
operating for 20 years and fully amortize the cost of controls.
Proposed Determination: EPA proposes to find that it is not
reasonable to require additional controls on this facility at this
time. Natural gas engines similar to those at the Tucson Compressor
Station are found in various locations throughout Arizona. EPA's
assessment indicates that a state-wide or regional approach to
controlling this source category could result in significant emissions
reductions. Given the dispersed nature of these engines, it is not
practical for EPA to control these sources. Therefore, EPA proposes to
find that it is not reasonable to require additional controls on this
particular source at this time. This source category should be given
serious consideration for future planning periods, as it would be more
appropriately controlled by the State.
e. El Paso Natural Gas Company's Flagstaff Compressor Station
Costs of Compliance: This site includes two 5,500 hp compressor
engines. EPA's analysis indicates that the most cost-effective control
would be an air/fuel ratio controller that would
[[Page 9358]]
reduce emissions by 398 tpy at a cost of $432/ton.\151\
---------------------------------------------------------------------------
\151\ See spreadsheet ``Non EGU--RP--Ch5.xlsx'' in the docket.
---------------------------------------------------------------------------
Time Necessary for Compliance: The Institute of Clean Air Companies
estimates that 8 to 14 weeks would be required to install these kinds
of controls.\152\
---------------------------------------------------------------------------
\152\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: The
controls may increase fuel usage by reducing the thermal efficiency of
the engines.
Remaining Useful Life: EPA assumes that the engines would continue
operating for 20 years and fully amortize the cost of controls.
Proposed RP Determination: EPA proposes to find that it is not
reasonable to require additional controls on this facility at this
time. Natural gas engines similar to those comprising the Flagstaff
Compressor Station are found in various locations throughout Arizona.
EPA's assessment indicates that a state-wide or regional approach to
controlling this source category could result in significant emissions
reductions. Given the dispersed nature of these engines, many of which
may fall into the area source category discussed above, it is not
practical for EPA to control these sources. Therefore, EPA proposes to
find that it is not reasonable to require additional controls on this
particular source at this time. This source category should be given
serious consideration for future planning periods.
f. Tucson Electric Power Sundt Station (Units 1-3)
Costs of Compliance: TEP Sundt has three natural gas-fired boilers
rated at approximately 1,220 MMBTU/hr each. EPA's analysis indicates
that the most cost-effective control would be ultra-low NOX
burners (ULNB). This retrofit would reduce emissions from Unit 1 by 46
tpy at a cost of $8,300/ton. It would reduce emissions from Unit 2 by
55 tpy at a cost of $7,000/ton. The retrofit would reduce emissions
from Unit 3 by 90 tpy at a cost of $4,400/ton. As shown in Table 47,
modeling indicates that these controls would provide a 0.40 dv
visibility benefit at the most improved Class I area.
Time Necessary for Compliance: The Institute of Clean Air Companies
estimates that 6 to 8 months would be required to install these kinds
of controls.\153\
---------------------------------------------------------------------------
\153\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: The
ultra-low-NOX burners may reduce the thermodynamic
efficiency of the boilers and require an increase in fuel consumption.
Remaining Useful Life: EPA assumes that the boilers would continue
operating for 20 years and fully amortize the cost of controls.
Proposed RP Determination: EPA proposes to find that it is not
reasonable to require additional controls on this facility at this
time. As noted above, ULNB has cost-effectiveness values for Sundt
Units 1-3 in the range of $4,000 to 7,000 per ton. These costs are
relatively high in light of the anticipated visibility benefits of the
controls. However, this decision should be revisited in future planning
periods, particularly if these units operate at a higher capacity
factor in the future.
Degree of Improvement in Visibility: Modeling indicates that
installation of ULNB on all three units would provide a 0.40 dv
visibility benefit at the most improved Class I area, Saguaro National
Park, as shown in Table 47. Note that all of these results assume that
SNCR has been applied to Sundt Unit 4, consistent with EPA's previous
BART determination for that unit. The visibility cost-effectiveness
values are based on an annualized cost of $1.2 million per year, based
on the analysis by UNC, contractor to EPA.\154\
---------------------------------------------------------------------------
\154\ Technical Analysis for Arizona and Hawaii Regional Haze
FIPs: Task 9: Five-Factor RP Analyses for TEP Springerville, APS
Cholla, TEP Sundt, CalPortland Cement and Phoenix Cement Plants,
Contract No. EP-D-07-102, Work Assignment 5-12; Prepared for EPA
Region 9 by University of North Carolina at Chapel Hill, ICF
International, and Andover Technology Partners; October 3, 2012,
Table 20.
Table 47--Sundt Unit 1, 2 and 3: Visibility Impact and Improvement From
NOX Controls
------------------------------------------------------------------------
Visibility Visibility
impact improvement
Distance -------------- from control
Class I area (km) Base case -------------
(SNCR on
Unit 4) ULNB
------------------------------------------------------------------------
Chiricahua NM.................. 144 0.43 0.08
Chiricahua WA.................. 141 0.51 0.07
Galiuro WA..................... 64 1.10 0.22
Gila WA........................ 232 0.17 0.02
Mazatzal WA.................... 203 0.19 0.02
Mount Baldy WA................. 232 0.15 0.02
Pine Mountain WA............... 247 0.15 0.01
Saguaro NP..................... 17 3.40 0.40
Sierra Ancha WA................ 178 0.19 0.02
Superstition WA................ 137 0.32 0.04
Cumulative (sum)............... ........... 6.6 0.9
Maximum........................ ........... 3.40 0.40
CIAs >= 0.5 dv....... ........... 3 0
Million $/dv (cumul. dv)....... ........... ............ $1.3
Million $/dv (max. dv)......... ........... ............ $2.9
------------------------------------------------------------------------
[[Page 9359]]
g. Ina Road Sewage Plant
Costs of Compliance: This site has seven 1,000 hp natural gas-fired
internal combustion engines. EPA's analysis indicates that the most
cost-effective control is non-selective catalytic reduction (NSCR).
Installation of this control would reduce emissions by 1,029 tpy at a
cost of $210/ton.\155\
---------------------------------------------------------------------------
\155\ See spreadsheet ``Non EGU--RP--Ch5.xlsx'' in the docket.
---------------------------------------------------------------------------
Time Necessary for Compliance: The Institute of Clean Air Companies
estimates that 8 to 14 weeks would be required to install these kinds
of controls.\156\
---------------------------------------------------------------------------
\156\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: The
control measure may decrease the thermodynamic efficiency of the
engines and increase fuel usage.
Remaining Useful Life: EPA assumes that the engines would continue
operating for 20 years and fully amortize the cost of controls.
Proposed RP Determination: EPA proposes to find that it is not
reasonable to require additional controls on this facility at this
time. Natural gas engines similar to those at the Ina Road Sewage Plant
are found in many locations throughout Arizona. EPA's assessment
indicates that a state-wide or regional approach to controlling this
source category could result in significant emissions reductions. Given
the dispersed nature of these engines, many of which may fall into the
area source category discussed above, it is not practical for EPA to
control these sources. Therefore, EPA proposes to find that it is not
reasonable to require additional controls on this particular source at
this time. This source category should be given serious consideration
for future planning periods, as it would be more appropriately
controlled by the State.
h. Tucson Electric Power Springerville Plant
Costs of Compliance: TEP Springerville Plant Units 1 and 2 are
4,700 MMBtu/hr tangential coal-fired boilers, which currently employ
LNB with OFA for NOX control. EPA identified two feasible
additional controls: SNCR and SCR. The estimated emission reductions
and costs for these two options are summarized in Tables 48 and 49.
Table 48--TEP Springerville 1 and 2: NOX Emission Estimates
----------------------------------------------------------------------------------------------------------------
NOX emissions Emission
------------------------------------------------ reduction
Control option ---------------
lb/MMBtu lb/hr tpy tpy
----------------------------------------------------------------------------------------------------------------
Springerville 1:
Baseline (LNB+OFA).......................... 0.18 769 2,189
SNCR........................................ 0.13 538 1532 657
SCR......................................... 0.05 212 605 1,584
Springerville 2:
Baseline (LNB+OFA).......................... 0.19 798 2,448
SNCR........................................ 0.13 559 1714 734
SCR......................................... 0.05 210 644 1,804
----------------------------------------------------------------------------------------------------------------
Table 49--TEP Springerville 1 and 2: NOX Control Cost Estimates
--------------------------------------------------------------------------------------------------------------------------------------------------------
Total capital Annualized Annual O&M Total annual Cost-effectiveness ($/ton)
cost capital cost costs cost -------------------------------
Control option ----------------------------------------------------------------
$ $/yr $/yr $/yr Ave Incr
--------------------------------------------------------------------------------------------------------------------------------------------------------
Springerville 1:
Baseline (LNB+OFA)
SNCR................................................ $8,496,000 $903,914 $1,933,059 $2,836,973 $4,320
SCR................................................. 71,796,257 7,638,614 3,181,809 10,820,423 6,829 $8,606
Springerville 2:
Baseline (LNB+OFA)
SNCR................................................ 8,496,000 903,914 2,141,291 3,045,205 4,146
SCR................................................. 71,402,351 7,596,705 3,379,514 10,976,219 6,085 7,416
--------------------------------------------------------------------------------------------------------------------------------------------------------
Time Necessary for Compliance: Given the estimate from the
Institute of Clean Air Companies \157\ that approximately a year is
required to install SNCR and the estimate of three years for installing
SNCR on a cement kiln discussed previously in this notice. EPA
estimates that SNCR could be installed in less than three years. In our
previous Arizona FIP action, EPA estimated that 5 years would be
required to install SCR on coal-fired boilers.\158\ That estimate also
holds for this source.
---------------------------------------------------------------------------
\157\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
\158\ See 77 FR 42834 at 42865 for more details.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance: SCR
and SNCR can result in additional ammonia emissions. There is also
increased truck traffic bringing the reagent on site. SCR will also
slightly reduce the efficiency of the plant, resulting in increased
fuel usage.
Remaining Useful Life: EPA assumes that this plant would continue
operating for 20 years and fully amortize the cost of controls.
Degree of Improvement in Visibility: As shown in Table 50, CALPUFF
modeling indicates that SNCR at Units 1 and 2 would provide a 0.18 dv
visibility benefit at the most affected Class I area and a cumulative
0.8 dv benefit across all affected areas. SCR would provide a 0.41 dv
benefit at the most affected Class I area and
[[Page 9360]]
cumulative 1.7 dv across all affected areas.
Table 50--Springerville Units 1 & 2: Visibility Impact and Improvement From NOX Controls
----------------------------------------------------------------------------------------------------------------
Impact Improvement from control
Class I area Distance (km) -----------------------------------------------
Base case SNC (ctrl-1) SCR (ctrl-2)
----------------------------------------------------------------------------------------------------------------
Bandelier NM.................................... 298 1.08 0.07 0.13
Chiricahua NM................................... 253 0.85 0.07 0.14
Chiricahua WA................................... 264 0.88 0.00 0.01
Galiuro WA...................................... 211 0.95 0.03 0.08
Gila WA......................................... 111 4.39 0.18 0.41
Grand Canyon NP................................. 302 0.79 0.07 0.07
Mazatzal WA..................................... 209 0.86 0.01 0.01
Mount Baldy WA.................................. 51 3.63 0.13 0.32
Petrified Forest NP............................. 79 2.46 0.06 0.09
Pine Mountain WA................................ 236 0.67 0.02 0.06
Saguaro NP...................................... 263 0.57 0.01 0.04
San Pedro Parks WA.............................. 281 1.53 0.05 0.23
Sierra Ancha WA................................. 165 1.01 0.02 0.05
Superstition WA................................. 194 0.52 0.03 0.06
Sycamore Canyon WA.............................. 263 0.65 0.02 0.04
Cumulative (sum)................................ .............. 20.8 0.8 1.7
Maximum......................................... .............. 4.39 0.18 0.41
CIAs >= 0.5 dv........................ .............. 15 0 0
---------------------------------------------------------------
Million $/dv (cumul. dv)........................ .............. .............. $7.3 $12.6
Million $/dv (max. dv).......................... .............. .............. $32.2 $53.4
----------------------------------------------------------------------------------------------------------------
Proposed RP Determination: EPA proposes to determine that it is not
reasonable to require additional controls at Springerville Units 1 and
2 at this time. While the cost per ton for SNCR may be reasonable, the
projected visibility benefits are relatively small (0.18 dv at the most
affected area). The projected visibility benefits of SCR are larger
(0.41 dv at the most affected area), but we do not consider them
sufficient to warrant the relatively high cost of controls for purposes
of RP in this planning period. However, these units should be
considered for additional NOX controls in future planning
periods.
i. El Paso Natural Gas Williams Compressor Station
Costs of Compliance: This site consists of five 2,500 hp engines,
one 3,400 hp engine, and one 32,200 hp gas turbine. EPA's analysis
indicates that air/fuel ratio controllers are the most cost-effective
controls for the five 2,500 hp engines and would reduce emissions by
288 tpy at a cost of $547/ton. Our analysis indicates that an air/fuel
ratio controller is also the most cost-effective control for the 3,400
hp engine and would reduce emissions from that engine by 131 tpy at a
cost of $444/ton. Our analysis further indicates that water injection
would be the most cost-effective control for the gas turbine and would
reduce emissions from that engine by 505 tpy at a cost of $854/
ton.\159\
---------------------------------------------------------------------------
\159\ See spreadsheet ``Non EGU--RP--Ch5.xlsx'' in the docket.
---------------------------------------------------------------------------
Time Necessary for Compliance: The Institute of Clean Air Companies
estimates that 8 to 14 weeks would be required to install these kinds
of controls.\160\
---------------------------------------------------------------------------
\160\ Typical Installation Timelines for NOX
Emissions Control Technologies on Industrial Sources, Institute of
Clean Air Companies, December 4, 2006.
---------------------------------------------------------------------------
Energy and Non-Air Quality Environmental Impacts of Compliance:
These controls may increase fuel usage by reducing the thermal
efficiency of the engines.
Remaining Useful Life: EPA assumes that the engines would continue
operating for 20 years and fully amortize the cost of controls.
Proposed RP Determination: EPA proposes to find that it is not
reasonable to require additional controls on this facility at this
time. Natural gas engines similar to those comprising the Williams
Compressor Station are found in various locations throughout Arizona.
EPA's assessment indicates that a state-wide or regional approach to
controlling this source could result in significant emissions
reductions. Given the dispersed nature of these engines, many of which
may fall into the area source category discussed above, it is not
practical for EPA to control these sources. Therefore, EPA proposes to
find that it is not reasonable to require additional controls on this
particular source at this time. This source category should be given
serious consideration for future planning periods, as it would be more
appropriately controlled by the State.
B. Reasonable Progress Analysis of Area Sources for NOX and SO2
1. Identification of Area Sources for NOX and
SO2.
The initial step in our area source RP analysis was the
identification of specific SO2 and NOX area
source categories to evaluate for potential controls. To that end, we
examined data from the 2008 National Emissions Inventory (NEI) to
determine the most significant area sources of SO2 and
NOX. This analysis is described in the TSD, and the results
are summarized in Tables 51 and 52. As discussed in the TSD, there are
significant uncertainties in the area source emissions inventory for
Arizona. In spite of the uncertainty, it is evident that the primary
area source categories of most concern are Industrial and Commercial
Boilers and Internal Combustion Engines burning distillate fuel oil. A
third category, Residential Natural Gas Combustion, also comprises a
significant portion of NOX emissions. EPA has therefore
identified these categories as ``potentially affected sources.'' EPA
proposes to find that the remaining source categories comprise too
small of a percentage contribution to
[[Page 9361]]
overall emissions to justify consideration for additional controls in
this initial planning period.
Table 51--Significant Area Sources of NOX in Arizona
----------------------------------------------------------------------------------------------------------------
Portion of
Source Tons per year total area Cumulative
Source type classification (2008) source portion (%)
code emissions (%)
----------------------------------------------------------------------------------------------------------------
Industrial Boilers and Internal Combustion 2102004000 2,300 29.3 29.3
Engines (burning distillate fuel oil).......
Residential Natural Gas Combustion........... 2104006000 1,645.7 20.2 49.5
Industrial Natural Gas Combustion............ 2102006000 765.4 9.4 58.8
Open Burning, Land Clearing Debris........... ................ 727.0 8.9 67.7
----------------------------------------------------------------------------------------------------------------
Table 52--Significant Area Sources of SO2 in Arizona
----------------------------------------------------------------------------------------------------------------
Portion of
Source Tons per year total area Cumulative
Source type classification (2008) source portion (%)
code emissions (%)
----------------------------------------------------------------------------------------------------------------
Industrial Boilers and Internal Combustion 2102004000 1652.1 65.3 65.3
Engines (burning distillate fuel oil)........
Commercial and Institutional Boilers and 2103004000 483.5 19.1 84.5
Internal Combustion Engines (burning
distillate fuel oil).........................
Industrial processes not elsewhere classified. 2399000000 110.4 4.4 88.8
----------------------------------------------------------------------------------------------------------------
2. Analysis of Significant Area Source Categories
a. Approach to Area Source Analysis
In conducting an RP analysis for area source, EPA encountered
significant limitations on the availability and accuracy of data
concerning the relevant source categories. For purposes of emission
inventory development, an area source is not a single facility, but a
category of polluting sources known to exist within a certain
geographic area (such as a county), whose actual number, age, and
design is not known. The emissions from area sources are usually
estimated based on a ``top-down'' method, where a surrogate piece of
information, such as the number of people living in a county or the
gallons of diesel fuel sold there in a given year, is used to estimate
emissions. Each of the source categories analyzed has an emissions
estimate derived from Federal, state, or local databases of fuel
consumption. In the aggregate, these numbers are sufficiently accurate
for most analyses. However, they do not provide adequate detail for EPA
to precisely estimate the actual costs and benefits of controlling the
existing population of sources.
Given these limitations in available data, EPA's analyses of area
sources are limited in scope. For each category we have developed
ranges for the estimated cost of compliance and general information
about each of the other factors, based largely on data from three
sources: the WRAP Four-Factor Analysis report, \161\ EPA's Control
Strategy Tool, and the documentation for EPA's AirControlNet tool.\162\
The WRAP report lists several possible NOX and
SO2 controls for industrial boilers and internal combustion
engines, depending on their size and pre-existing controls. The WRAP
report also addresses the other mandatory factors for an RP analysis.
The Control Strategy Tool is EPA's most current tool for assessing the
cost-effectiveness of control strategies for various source categories.
EPA used this tool to confirm that the cost estimates in the WRAP
report are still reasonable.\163\ We also consulted the AirControlNet
documentation report that contains the most current data on the cost-
effectiveness of NOX controls for residential natural gas
combustion. Finally, while we lacked sufficient data to conduct
visibility modeling for particular categories of area sources, we have
analyzed the overall contribution of area sources to nitrate and
sulfate-caused visibility impairment in Arizona's Class I areas in
order to estimate the potential benefits of controls. The results of
this analysis are provided below, following the results of the four-
factor analyses for all of the source categories.
---------------------------------------------------------------------------
\161\ ``Supplementary Information for Four Factor Analyses by
WRAP States,'' EC/R Incorporated, corrected version, April 20, 2010.
\162\ ``AirControlNet, Version 4.1,'' May 2006, E.H. Pechan and
Associates.
\163\ See spreadsheet titled ``AZ FIP Cost Analysis--for Greg
Nudd Rg 9--2013-08-13.xls''.
---------------------------------------------------------------------------
b. RP Analysis of Industrial, Commercial, and Institutional Boilers
Burning Distillate Fuel Oil
Cost of Compliance: The estimated cost-effectiveness values for
NOX control options are:
LNB: $400-7,000/ton;
LNB/OFA: $400-7,000/ton;
SNCR: $400-6,900/ton;
SCR: $1,000-8,000/ton.
The estimated cost-effectiveness values for SO2 control
options for this category are:
DSI: $5,000-11,000/ton;
Wet FGD: $6,000-13,000/ton.
Time Necessary for Compliance: Installation of the control devices,
in most cases, should take no more than 2-3 years. The only possible
exception may be for installation of SCR, which may take as long as 5
years.
Energy and Non-Air Quality Environmental Impacts of Compliance: LNB
may reduce combustion efficiency and slightly increase fuel
consumption; SNCR and SCR would require some electricity use and
environmental impacts from ammonia slip and transport and storage of
the reagent. Wet FGD requires large quantities of water and requires
disposal of wet ash.
Remaining Useful Life: It is reasonable to assume that the units
would remain in use long enough to fully recover the costs of controls.
[[Page 9362]]
c. RP Analysis of Industrial, Commercial, and Institutional Internal
Combustion Engines Burning Distillate Fuel Oil
Costs of Compliance: We estimate the following cost-effectiveness
values for NOX control options:
Ignition timing retard: $1,000-2,200/ton;
Exhaust Gas Recirculation: $780-2,000/ton;
SCR: $3,000-7,700/ton;
Replacement with Tier 4 engines: $900-2,400/ton.
We did not identify any technically feasible options for SO2
control other than lower sulfur fuel.
Time Necessary for Compliance: Installation of the control devices,
in most cases, should take no more than 2-3 years. The only possible
exception may be for installation of SCR, which may take as long as 5
years.
Energy and Non-Air Quality Environmental Impacts of Compliance: SCR
would require some electricity use and there may also be environmental
impacts from ammonia slip and transport and storage of the reagent. The
other options would not have negative energy or non-air quality
environmental impacts.
Remaining Useful Life: It is reasonable to assume that the units
would remain in use long enough to fully recover the costs of controls.
d. RP Analysis of Residential Natural Gas Combustion
Costs of Compliance: We estimate the following cost-effectiveness
values for NOX control options:
Replace space heaters with Low NOX equivalent:
$1,600/ton;
Replace water heaters with Low NOX equivalent:
$1,230/ton.\164\
\164\ Both estimates from AirControlNet Manual p. III-90 and are
in 1990 dollars.
---------------------------------------------------------------------------
SO2 controls are not needed for this category due to low
sulfur content of pipeline natural gas.
Time Necessary for Compliance: Installation of the new devices, in
most cases, should take no more than 2-3 years.
Energy and Non-Air Quality Environmental Impacts of Compliance: We
did not identify any energy or non-air quality environmental impacts.
Remaining Useful Life: This factor is not applicable for a unit
replacement.
Visibility Significance of Area Sources: As explained above, we do
not have sufficient information to assess the likely visibility
benefits of requiring controls on particular categories of area
sources. However, in order to estimate the total potential visibility
benefits that might result from controlling NOX and
SO2 emissions from area sources, we have analyzed the
overall contribution of area sources to nitrate- or sulfate-caused
visibility impairment in Arizona's Class I areas. The relative
contribution can be estimated by reviewing the results of the
Particulate Source Apportionment Technology (PSAT) modeling conducted
by the WRAP. This method and our evaluation of it are described in the
WRAP TSD prepared by EPA.\165\ Tables 53 and 54 below compare the
contribution of Arizona area sources to visibility impairment in
Arizona's Class I areas with the contributions from point and mobile
sources.\166\ Table 53 shows the relative contribution of these Arizona
source categories to the 2018 predicted total nitrate impairment at the
Class I areas. Table 54 shows the same data for 2018 predicted total
sulfate impairment. Nitrate and sulfate comprise a subset of the total
visibility impairment at these Class I areas. To calculate the source
category's total contribution to visibility impairment, one would have
to account for the other pollutants (such as coarse mass, black carbon,
etc.). EPA has not made that calculation here, as we are looking
specifically at nitrate and sulfate impairment for this RP analysis.
---------------------------------------------------------------------------
\165\ ``Technical Support Document for Technical Products
Prepared by the Western Regional Air Partnership (WRAP) in Support
of Western Regional Haze Plans,'' February 28, 2011.
\166\ See http://vista.cira.colostate.edu/tss/Results/HazePlanning.aspx, select ``Emissions and Source Apportionment'' and
the 2018 Base Case (base 18b) emissions scenario.
Table 53--2018 Projected Nitrate Impairment: Comparison of Arizona
Source Categories
------------------------------------------------------------------------
Arizona Arizona
area point Arizona
Class I area sources sources mobile
(%) (%) sources
------------------------------------------------------------------------
CHIR1..................................... 0.7 5.1 5.1
GRCA2..................................... 2.9 7.4 18.3
IKBA1..................................... 4.1 12.3 23.6
BALD1..................................... 0.8 18.1 8.7
PEFO1..................................... 1.7 26.7 14.2
SAGU1..................................... 5.2 19.3 27.5
SAWE1..................................... 4.3 18.4 23.5
SIAN1..................................... 4.1 5.0 20.7
TONT1..................................... 5.4 12.7 30.2
SYCA1..................................... 2.7 14.0 19.3
------------------------------------------------------------------------
Table 54--2018 Projected Sulfate Impairment: Comparison of Arizona
Source Categories
------------------------------------------------------------------------
Arizona Arizona Arizona
Class I area area point mobile
sources sources sources
------------------------------------------------------------------------
CHIR1..................................... 0.4 4.7 0.5
GRCA2..................................... 0.4 4.3 1.0
IKBA1..................................... 1.0 6.7 1.2
BALD1..................................... 0.7 11.3 0.7
PEFO1..................................... 0.7 19.6 0.9
SAGU1..................................... 2.1 10.2 1.7
SAWE1..................................... 1.7 9.6 1.4
SIAN1..................................... 0.8 7.8 1.1
TONT1..................................... 1.3 7.8 2.8
SYCA1..................................... 1.0 3.5 0.8
------------------------------------------------------------------------
As indicated in Tables 53 and 54, area sources in Arizona currently
comprise a relatively small portion of the visibility impairment due to
nitrate and sulfate, so the potential visibility benefits of
NOX or SO2 controls on these sources would be
relatively small at this point in time. However, the relative
contribution of area sources to visibility impairment at Arizona's
Class I areas may increase over time, as additional point source and
mobile source controls are implemented. Therefore, additional analysis
of these sources will be necessary in future planning periods.
f. Proposed RP Determination for Area Sources
EPA proposes to find that it is not reasonable to require
additional controls on area sources of NOX and
SO2 at this time. There are significant uncertainties about
the costs and potential benefits of such rules at this time.
Furthermore, the visibility benefits due to area source controls are
likely to be much smaller than the significant reductions in
SO2 and NOX emissions from point sources achieved
during this planning period. We also note that no other Regional Haze
SIP or FIP has imposed controls on such sources primarily to ensure
reasonable progress.\167\ EPA will work with the State and the relevant
regional planning organizations to improve our understanding of the
nature of these area source emissions, the costs and methods of
controlling them, and their impact on visibility at Class I areas.
Based on the results of these efforts,
[[Page 9363]]
these source categories should be carefully considered in future
Regional Haze SIPs.
---------------------------------------------------------------------------
\167\ The Colorado Regional Haze SIP includes rules limiting
emissions from certain Reciprocating Internal Combustion Engines. 77
FR 18052, 18089. However these rules are part of a State regulation
intended to control ozone rather than regional haze. Colorado Air
Quality Control Commission, Regulation Number 7, 5 CCR 1001-9,
Control of Ozone via Ozone Precursors, Section XVII, Statewide
Control for Oil and Gas Operations and Natural Gas-Fired
Reciprocating Internal Combustion Engines, subsection E.3.a,
(Regional Haze SIP) Rich Burn Reciprocating Internal Combustion
Engines.
---------------------------------------------------------------------------
C. Reasonable Progress Goals
We are proposing reasonable progress goals (RPGs) that are
consistent with the combination of control measures included in the
Arizona RH SIP measures that we previously approved; \168\ the partial
RH FIP that we promulgated on December 5, 2012; \169\ and the partial
RH FIP we are proposing today. In total, these final and proposed
controls to meet the BART and RP requirements will result in higher
emissions reductions and commensurate visibility improvements beyond
what was in the State's plan. As a result, we expect that the
visibility levels at Arizona Class I areas will be substantially better
than predicted in the WRAP modeling that served as the basis for the
State's RPGs. In addition, our final BART FIP for the Four Corners
Power Plant on the Navajo Nation is expected to result in tens of
thousands of tons per year of additional NOX reductions that
will benefit some of Arizona's Class I areas. Likewise, our proposed
BART FIP for the Navajo Generating Station, if finalized, will result
in substantial visibility benefit for Class I areas.
---------------------------------------------------------------------------
\168\ 77 FR 72512, 78 FR 46142.
\169\ 77 FR 72512.
---------------------------------------------------------------------------
While we would prefer to quantify these proposed RPGs for each of
Arizona's 12 Class I areas based on the new state and federal plans, we
lack sufficient time and resources to conduct the type of regional-
scale modeling required to develop such numerical RPGs.\170\
Nonetheless, we anticipate that the additional controls required in
EPA's Regional Haze FIPs will result in an increase in visibility
improvement during the 20 percent worst days and the 20 percent best
days in all of Arizona's Class 1 Areas.
---------------------------------------------------------------------------
\170\ The regional-scale modeling that formed the basis for
Arizona's RPGs was developed by the WRAP's Regional Modeling Center
over the course of several years with input from numerous sources.
---------------------------------------------------------------------------
D. Meeting the Uniform Rate of Progress
As explained in our proposed and final rules on the Arizona RH SIP,
the State set RPGs that provide for slower rates of improvement in
visibility than the URP for each of the State's twelve Class I
areas.\171\ Given the variety and location of the sources contributing
to visibility impairment in Arizona, EPA considers it unlikely that all
of Arizona's Class I areas will meet the URP during this planning
period, even with the additional controls required in EPA's Regional
Haze FIPs. Therefore, EPA must demonstrate that it is not reasonable to
provide for rates of progress consistent with the URP for this planning
period, based upon the four RP factors.\172\ Given that this
demonstration must be based on the same four factors as the initial RP
analysis, EPA proposes to find that the extensive reasonable progress
analysis underlying our actions on the Arizona SIP, and the reasonable
progress analysis found in this proposal are sufficient to make this
demonstration. In particular, for the reasons explained in our proposed
and final rules on the Arizona RH SIP, we have approved Arizona's
determinations that it is not reasonable to require additional controls
to address organic carbon, elemental carbon, coarse mass and fine soil
during this planning period.\173\ We also approved the State's decision
not to require additional controls on non-BART point sources of
SO2.\174\ Moreover, based on the analyses set out in the
preceding sections of this document, we are now proposing to find that
it is not reasonable to require additional controls on most point
sources of NOX or area sources of NOX and
SO2 during this planning period. However, we are proposing
to require additional NOX controls on two cement kilns.
Based on all of these analyses, we propose to find that it is not
reasonable for any of Arizona's Class I areas to meet the URP during
this planning period.
---------------------------------------------------------------------------
\171\ See 77 FR 75728, 78 FR 29298 and 78 FR 46160.
\172\ 40 CFR 51.308(d)(1)(ii).
\173\ See 77 FR 75728 for a discussion on sources of organic
carbon and elemental carbon (fires), and 78 FR 29297-29299 for a
discussion of coarse mass and fine soil.
\174\ See 78 FR 46172.
---------------------------------------------------------------------------
VII. EPA's Proposed Long-Term Strategy Supplement
In our final rule on the Arizona RH SIP published on July 30, 2013,
we disapproved portions of the State's LTS related to three RHR
requirements. These requirements were for measures needed to achieve
emission reductions for out-of-state Class I areas, emissions
limitations and schedules for compliance to achieve the reasonable
progress goals, and enforceability of emissions limitations and control
measures.\175\ These RHR requirements are found in 40 CFR
51.308(d)(3)(ii), (v)(C) and (v)(F). We now are obligated to address
these requirements through a FIP under CAA section 110(c). In this
section, we describe each of these requirements, our rationale for
disapproving these elements in the Arizona RH SIP, and propose how to
address these requirements in our FIP.
---------------------------------------------------------------------------
\175\ See 78 FR 46173 (codified at 40 CFR 52.145(e)(ii)).
---------------------------------------------------------------------------
A. Emission Reductions for Out-of-State Class I Areas
Under the RHR, where a state has participated in a regional
planning process, the state's LTS must include all measures needed to
achieve that state's apportionment of emission reduction obligations
agreed upon through that process.\176\ Arizona participated in a
regional planning process through the WRAP and incorporated the WRAP-
developed visibility modeling into the Arizona RH SIP. However, the
Arizona RH SIP did not include all measures needed to achieve the
State's apportionment of emission reductions that were included in the
WRAP modeling. In particular, Arizona's BART determinations lacked the
necessary compliance schedules and requirements for operation and
maintenance of control equipment and monitoring, recordkeeping and
reporting to ensure that the assumed reductions at Arizona's BART
sources are achieved. Therefore, we disapproved this element of the
Arizona RH SIP.
---------------------------------------------------------------------------
\176\ 40 CFR 51.308(d)(3)(ii).
---------------------------------------------------------------------------
B. Emissions Limitations and Schedules for Compliance To Achieve RPGs
One of the factors a state must consider in developing its LTS is
emissions limitations and schedules for compliance to achieve the
State's RPGs for its own Class I areas.\177\ As explained in the
preceding section, the Arizona RH SIP did not contain any enforceable
emission limitations or schedules for compliance to achieve the State's
RPGs. Therefore, we found that the Arizona RH SIP did not meet this
requirement.
---------------------------------------------------------------------------
\177\ 40 CFR 51.308(d)(3)(v)(C).
---------------------------------------------------------------------------
C. Enforceability of Emissions Limitations and Control Measures
Another factor a state must consider in developing its LTS is the
enforceability of emissions limitations and control measures.\178\ As
explained in the preceding sections, Arizona's BART determinations lack
provisions to ensure their enforceability. Therefore, we disapproved
the Arizona RH SIP with respect to this requirement.
---------------------------------------------------------------------------
\178\ 40 CFR 51.308(d)(3)(v)(F).
---------------------------------------------------------------------------
D. Proposed Partial LTS FIP
The primary flaw in Arizona's LTS is the lack of enforceable
emission limitations for BART controls. We propose to remedy this
deficiency by promulgating BART emission limitations and compliance
schedules as
[[Page 9364]]
well as monitoring, recordkeeping and reporting requirements, to ensure
the enforceability of these limits.
1. Enforceability Requirements for Arizona and EPA's Phase 1 BART
Determinations
As part of our final rule published on December 5, 2012, regarding
BART for Apache Generating Station, Cholla Power Plant and Coronado
Generating Station, we promulgated compliance deadlines and
requirements for equipment maintenance and operation including
monitoring, recordkeeping and reporting, to ensure the enforceability
of both Arizona's and EPA's BART determinations.
2. Enforceability Requirements for EPA's Proposed Phase 3 BART and RP
Determinations
As described above, today, we are proposing to promulgate similar
requirements for the remaining subject-to-BART sources and pollutants
in Arizona. We are also proposing emission limitations and compliance
requirements for two RP sources: the Phoenix Cement Clarkdale Plant and
the CalPortland Rillito Plant.
3. Enforceability Requirements for Arizona's Phase 2 BART
Determinations
The final element of our proposed LTS consists of enforceable
emission limitations and associated requirements for PM10 at
the Hayden and Miami Copper Smelters. While we previously approved the
State's determination that existing controls constitute BART for
PM10 at each of these facilities, the Arizona RH SIP lacked
any emission limitation or associated requirements to ensure the
enforceability of these determinations, as required under the CAA and
EPA's regulations.\179\ Therefore, we are proposing to promulgate such
limits and associated compliance requirements for these BART
determinations, as necessary to ensure their enforceability.
---------------------------------------------------------------------------
\179\ See CAA section 110(a)(2)(F) and 40 CFR 51.212(c),
51.308(d)(3)(v)(C) and (F).
---------------------------------------------------------------------------
a. Hayden Smelter PM10
In its BART analysis for PM10, ASARCO relied on the
particulate limits established in National Emission Standard for
Hazardous Air Pollutants (NESHAP) Subpart QQQ, Primary Copper Smelting
at 40 CFR 63.1444(d)(5) and (6).\180\ These limits and associated
monitoring requirements formed the basis for ASARCO's BART
determination, which ADEQ incorporated in its Regional Haze SIP.\181\
We are now proposing to incorporate these requirements into the FIP. In
particular, we propose to set a limit of 6.2 mg/dscm non-sulfuric acid
particulate matter from the primary capture system, and a limit of 23
mg/dscm particulate matter from the secondary capture system, as
measured using the test methods specified in 40 CFR 63.1450(b). We
propose to require demonstration of compliance with these limits
through the applicable procedures in 40 CFR 63.1451 and 1453.
---------------------------------------------------------------------------
\180\ Letter from Eric Hiser, Counsel for ASARCO, to Balaji
Vaidyanathan, ADEQ dated March 20, 2013, page 5.
\181\ Arizona RH SIP Supplement (May 3, 2013), Appendix D, page
23, and Section XII.
---------------------------------------------------------------------------
b. Miami Smelter PM10
In the Arizona Regional Haze SIP, ADEQ determined that the NESHAP
for Primary Copper Smelting constitutes BART for PM emissions from the
Miami Smelter. Because the FMMI smelter is a major source of Hazardous
Air Pollutants (HAPs), and therefore subject to the requirements of the
NESHAP, these requirements are already incorporated into the facility's
Title V permit.\182\ We propose to find that these existing, federally
enforceable requirements are sufficient to ensure the enforceability of
ADEQ's PM10 BART determination for the Miami Smelter.
---------------------------------------------------------------------------
\182\ ADEQ Air Quality Class I Permit Number 53592 issued
November 26, 2012, attachment B.
---------------------------------------------------------------------------
VIII. EPA's Proposal for Interstate Transport
We propose that a combination of SIP and FIP measures will satisfy
the FIP obligation for the visibility requirement of CAA section
110(a)(2)(D)(i)(II) for the 1997 8-hour ozone, 1997 PM2.5,
and 2006 PM2.5 NAAQS. As discussed in section II.B
(``Overview of Proposed Actions; Interstate Transport of Pollutants
that affect Visibility'') of this proposed rule, EPA disapproved
Arizona's 2007 and 2009 Transport SIPs as well as its Regional Haze SIP
for the interstate transport visibility protection requirement of CAA
section 110(a)(2)(D)(i)(II) for the 1997 8-hour ozone, 1997
PM2.5, and 2006 PM2.5 NAAQS. As noted in our
proposed SIP action,\183\ we interpret the visibility requirement of
section 110(a)(D)(i)(II) as requiring states to include in their SIPs
either measures to prohibit emissions that would interfere with
attaining RPGs of Class I areas in other states, or a demonstration
that emissions from the state's sources and activities will not have
the prohibited impacts under the existing SIP. Arizona's 2007 and 2009
Transport SIP revisions indicated that the interstate transport
visibility requirement should be assessed in conjunction with the
Arizona RH SIP, but did not specify which parts of the RH SIP should be
considered as meeting the visibility requirement of section
110(a)(2)(D)(i)(II). Therefore we have considered the Arizona RH SIP as
a whole in assessing whether Arizona has met this visibility
requirement.
---------------------------------------------------------------------------
\183\ 77 FR 75704 at 75709.
---------------------------------------------------------------------------
As a result of the partial disapprovals of the Arizona RH SIP, we
found that the Arizona SIP did not contain adequate provisions to
prohibit emissions that may interfere with SIP measures required of
other states to protect visibility. Therefore, we disapproved Arizona's
submittals with respect to the interstate transport visibility
requirement for the 1997 8-hour ozone, 1997 PM2.5, and 2006
PM2.5 NAAQS, which triggered the obligation for EPA to
promulgate a FIP under CAA section 110(c)(1). We anticipated that this
FIP obligation could be satisfied by a combination of the State's
measures that we previously approved and EPA's promulgation of FIPs for
the disapproved elements of the Arizona RH SIP.\184\
---------------------------------------------------------------------------
\184\ 77 FR 75704 at 75736.
---------------------------------------------------------------------------
We propose to find that the combination of elements in the
applicable RH SIPs and FIPs will contain adequate provisions to
prohibit emissions from Arizona that would interfere with SIP measures
required of other states to protect visibility. These elements are the
Arizona RH SIP measures that we previously approved;\185\ the partial
RH FIP that we promulgated on December 5, 2012;\186\ and the partial RH
FIP we are proposing today. As explained in the LTS section, the
combination of all of these measures will ensure that the applicable
implementation plan (i.e., the combination of SIP and FIP measures)
will include all of the measures needed to achieve Arizona's allotment
of emission reductions agreed upon through the WRAP process. We propose
that this combination of SIP and FIP measures will satisfy the FIP
obligation for the visibility requirement of CAA section
110(a)(2)(D)(i)(II) for the 1997 8-hour ozone, 1997 PM2.5,
and 2006 PM2.5 NAAQS.
---------------------------------------------------------------------------
\185\ 77 FR 72512, 78 FR 46142.
\186\ 77 FR 72512.
---------------------------------------------------------------------------
IX. Summary of EPA's Proposed Actions
A. Regional Haze
EPA is proposing a FIP to address the remaining portions of the
Arizona's RH SIP that we disapproved on July 30, 2013, which includes
requirements for Best Available Retrofit Technology, Reasonable
Progress, and the Long-term
[[Page 9365]]
Strategy. We are proposing more stringent emission limits on six
sources that impact visibility in 17 Class I areas inside and outside
the State. We welcome comments on all of our proposals and indicate
specific issues or areas where feedback would be particularly useful.
Our proposal includes compliance dates and specific requirements for
monitoring, recordkeeping, reporting and equipment operation and
maintenance for all of the units covered by this action as described in
Part 52 attached to this notice. Today's proposed FIP, once finalized,
along with previously approved SIPs and a finalized FIP, will
constitute Arizona's regional haze program for the first planning
period that ends in 2018.
B. Interstate Visibility Transport
We propose that the interstate transport visibility requirement of
section 110(a)(2)(D)(i)(II) for the 1997 8-hour ozone, 1997
PM2.5, and 2006 PM2.5 NAAQS is satisfied by a
combination of SIP and FIP elements. These elements are the Arizona RH
SIP measures that we previously approved; the partial RH FIP that we
promulgated on December 5, 2012; and the partial RH FIP we are
proposing today.
X. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
This proposed action is not a ``significant regulatory action''
under the terms of Executive Order 12866 (58 FR 51735, October 4, 1993)
and is therefore not subject to review under Executive Orders 12866 and
13563 (76 FR 3821, January 21, 2011). The proposed FIP applies to only
six facilities. It is therefore not a rule of general applicability.
B. Paperwork Reduction Act
This proposed action does not impose an information collection
burden under the provisions of the Paperwork Reduction Act, 44 U.S.C.
3501 et seq. Under the Paperwork Reduction Act, a ``collection of
information'' is defined as a requirement for ``answers to * * *
identical reporting or recordkeeping requirements imposed on ten or
more persons * * *.'' 44 U.S.C. 3502(3)(A). Because the proposed FIP
applies to just six facilities, the Paperwork Reduction Act does not
apply. See 5 CFR 1320(c). Burden means the total time, effort, or
financial resources expended by persons to generate, maintain, retain,
or disclose or provide information to or for a Federal agency. This
includes the time needed to review instructions; develop, acquire,
install, and utilize technology and systems for the purposes of
collecting, validating, and verifying information, processing and
maintaining information, and disclosing and providing information;
adjust the existing ways to comply with any previously applicable
instructions and requirements; train personnel to be able to respond to
a collection of information; search data sources; complete and review
the collection of information; and transmit or otherwise disclose the
information. An agency may not conduct or sponsor, and a person is not
required to respond to a collection of information unless it displays a
currently valid Office of Management and Budget (OMB) control number.
The OMB control numbers for our regulations in 40 CFR are listed in 40
CFR part 9.
C. Regulatory Flexibility Act
The Regulatory Flexibility Act (RFA) generally requires an agency
to prepare a regulatory flexibility analysis of any rule subject to
notice and comment rulemaking requirements under the Administrative
Procedure Act or any other statute unless the agency certifies that the
rule will not have a significant economic impact on a substantial
number of small entities. Small entities include small businesses,
small organizations, and small governmental jurisdictions. For purposes
of assessing the impacts of today's proposed rule on small entities,
small entity is defined as: (1) A small business as defined by the
Small Business Administration's (SBA) regulations at 13 CFR 121.201;
(2) a small governmental jurisdiction that is a government of a city,
county, town, school district or special district with a population of
less than 50,000; and (3) a small organization that is any not-for
profit enterprise which is independently owned and operated and is not
dominant in its field.
After considering the economic impacts of this proposed action on
small entities, I certify that this proposed action will not have a
significant economic impact on a substantial number of small entities.
None of the facilities subject to this proposed rule is owned by a
small entity.\187\ We continue to be interested in the potential
impacts of the proposed rule on small entities and welcome comments on
issues related to such impacts.
---------------------------------------------------------------------------
\187\ See Regulatory Flexibility Act Screening Analysis for
Proposed Arizona Regional Haze Federal Implementation Plan (EPA-R09-
OAR-2013-0588).
---------------------------------------------------------------------------
D. Unfunded Mandates Reform Act
Title II of the Unfunded Mandates Reform Act of 1995 (UMRA), Public
Law 104-4, establishes requirements for Federal agencies to assess the
effects of their regulatory actions on State, local, and Tribal
governments and the private sector. Under section 202 of UMRA, EPA
generally must prepare a written statement, including a cost-benefit
analysis, for proposed and final rules with ``Federal mandates'' that
may result in expenditures to State, local, and Tribal governments, in
the aggregate, or to the private sector, of $100 million or more
(adjusted for inflation) in any 1 year. Before promulgating an EPA rule
for which a written statement is needed, section 205 of UMRA generally
requires EPA to identify and consider a reasonable number of regulatory
alternatives and adopt the least costly, most cost-effective, or least
burdensome alternative that achieves the objectives of the rule. The
provisions of section 205 of UMRA do not apply when they are
inconsistent with applicable law. Moreover, section 205 of UMRA allows
EPA to adopt an alternative other than the least costly, most cost-
effective, or least burdensome alternative if the Administrator
publishes with the final rule an explanation why that alternative was
not adopted. Before EPA establishes any regulatory requirements that
may significantly or uniquely affect small governments, including
Tribal governments, it must have developed under section 203 of UMRA a
small government agency plan. The plan must provide for notifying
potentially affected small governments, enabling officials of affected
small governments to have meaningful and timely input in the
development of EPA regulatory proposals with significant Federal
intergovernmental mandates, and informing, educating, and advising
small governments on compliance with the regulatory requirements.
Under Title II of UMRA, EPA has determined that this proposed rule
does not contain a Federal mandate that may result in expenditures that
exceed the inflation-adjusted UMRA threshold of $100 million by State,
local, or Tribal governments or the private sector in any 1 year. In
addition, this proposed rule does not contain a significant Federal
intergovernmental mandate as described by section 203 of UMRA nor does
it contain any regulatory requirements that might significantly or
uniquely affect small governments.\188\
---------------------------------------------------------------------------
\188\ See ``Summary of EPA BART Cost Estimates'' in the docket.
---------------------------------------------------------------------------
[[Page 9366]]
E. Executive Order 13132: Federalism
Executive Order 13132 Federalism (64 FR 43255, August 10, 1999)
revokes and replaces Executive Orders 12612 (Federalism) and 12875
(Enhancing the Intergovernmental Partnership). Executive Order 13132
requires EPA to develop an accountable process to ensure ``meaningful
and timely input by State and local officials in the development of
regulatory policies that have federalism implications.'' ``Policies
that have federalism implications'' is defined in the Executive Order
to include regulations that have ``substantial direct effects on the
States, on the relationship between the national government and the
States, or on the distribution of power and responsibilities among the
various levels of government.'' Under Executive Order 13132, EPA may
not issue a regulation that has federalism implications, that imposes
substantial direct compliance costs, and that is not required by
statute, unless the Federal government provides the funds necessary to
pay the direct compliance costs incurred by State and local
governments, or EPA consults with State and local officials early in
the process of developing the proposed regulation. EPA also may not
issue a regulation that has federalism implications and that preempts
State law unless the Agency consults with State and local officials
early in the process of developing the proposed regulation.
This rule will not have substantial direct effects on the states,
on the relationship between the national government and the states, or
on the distribution of power and responsibilities among the various
levels of government, as specified in Executive Order 13132. In this
action, EPA is fulfilling our statutory duty under CAA Section 110(c)
to promulgate a partial Regional Haze FIP. Thus, Executive Order 13132
does not apply to this action. In the spirit of Executive Order 13132,
and consistent with EPA policy to promote communications between EPA
and State and local governments, EPA specifically solicits comment on
this proposed rule from State and local officials.
F. Executive Order 13175: Consultation and Coordination With Indian
Tribal Governments
Subject to the Executive Order 13175 (65 FR 67249, November 9,
2000) EPA may not issue a regulation that has tribal implications, that
imposes substantial direct compliance costs, and that is not required
by statute, unless the Federal government provides the funds necessary
to pay the direct compliance costs incurred by tribal governments, or
EPA consults with tribal officials early in the process of developing
the proposed regulation and develops a tribal summary impact statement.
EPA has concluded that this action, if finalized, will have tribal
implications, because it will impose substantial direct compliance
costs on tribal governments, and the Federal government will not
provide the funds necessary to pay those costs. PCC is a division of
Salt River Pima Maricopa Indian Community (SRPMIC or the Community) and
profits from the Phoenix Cement Clarkdale Plant are used to provide
government services to SRPMIC's members. Therefore, EPA is providing
the following tribal summary impact statement as required by section
5(b).
EPA consulted with tribal officials early in the process of
developing this regulation to permit them to have meaningful and timely
input into its development. In November 2012, we shared our initial
analyses with SRPMIC and PCC to ensure that the tribe had an early
opportunity to provide feedback on potential controls at the Clarkdale
Plant. PCC submitted comments on this initial analysis as part of the
rulemaking on the Arizona Regional Haze SIP and we revised our initial
analysis based on these comments. On November 6, 2013, the EPA Region 9
Regional Administrator met with the President and other representatives
of SRPMIC to discuss the potential impacts of the FIP on SRPMIC.
Following this meeting, staff from EPA, SPRMIC and PCC shared further
information regarding the Plant and potential impacts of the FIP on
SRPMIC.\189\
---------------------------------------------------------------------------
\189\ See Memorandum to Docket: Summary of Communications and
Consultation between EPA, PCC and SRPMIC (January 27, 2014).
---------------------------------------------------------------------------
During these consultations, SRPMIC expressed its concern regarding
the potential financial impacts of any new controls that might be
required at the Clarkdale Plant. In particular, SRPMIC requested that
EPA provide PCC with an extended compliance schedule for any controls
in order to enable PCC and SRPMIC to plan for such controls in their
long-term budgets and thus mitigate the potential impacts to the
Community.\190\ However, SRPMIC provided only limited information
documenting the potential for such impacts and claimed all such
information as CBI.
As explained above, EPA is proposing to determine that it is
reasonable to require installation of SNCR at Kiln 4 at the Clarkdale
Plant by December 31, 2018. EPA is also seeking comment on the
possibility of establishing an annual cap on NOX emissions
from Kiln 4 in lieu of a lb/ton emission limit. An annual cap would
allow SRPMIC to delay installation of controls until the Plant's
production returns to pre-recession levels and would thus help to
address the Community's concerns about the budgetary impacts of control
requirements. EPA specifically solicits additional comment on this
proposed rule from tribal officials.
G. Executive Order 13045: Protection of Children From Environmental
Health Risks and Safety Risks
Executive Order 13045: Protection of Children From Environmental
Health Risks and Safety Risks (62 FR 19885, April 23, 1997), applies to
any rule that: (1) Is determined to be economically significant as
defined under Executive Order 12866; and (2) concerns an environmental
health or safety risk that we have reason to believe may have a
disproportionate effect on children. EPA interprets EO 13045 as
applying only to those regulatory actions that concern health or safety
risks, such that the analysis required under section 5-501 of the EO
has the potential to influence the regulation. This action is not
subject to EO 13045 because it implements specific standards
established by Congress in statutes. However, to the extent this
proposed rule will limit emissions of NOX, SO2
and PM, the rule will have a beneficial effect on children's health by
reducing air pollution.
H. Executive Order 13211: Actions Concerning Regulations That
Significantly Affect Energy Supply, Distribution, or Use
This action is not subject to Executive Order 13211 (66 FR 28355
(May 22, 2001)), because it is not a significant regulatory action
under Executive Order 12866.
I. National Technology Transfer and Advancement Act
Section 12 of the National Technology Transfer and Advancement Act
(NTTAA) of 1995 requires Federal agencies to evaluate existing
technical standards when developing a new regulation. To comply with
NTTAA, EPA must consider and use ``voluntary consensus standards''
(VCS) if available and applicable when developing programs and policies
unless doing so would be inconsistent with applicable law or otherwise
impractical. EPA believes that VCS are inapplicable to this action.
Today's action does not
[[Page 9367]]
require the public to perform activities conducive to the use of VCS.
J. Executive Order 12898: Federal Actions To Address Environmental
Justice in Minority Populations and Low-Income Populations
Executive Order 12898 (59 FR 7629, February 16, 1994), establishes
federal executive policy on environmental justice. Its main provision
directs federal agencies, to the greatest extent practicable and
permitted by law, to make environmental justice part of their mission
by identifying and addressing, as appropriate, disproportionately high
and adverse human health or environmental effects of their programs,
policies, and activities on minority populations and low-income
populations in the United States.
We have determined that this proposed rule, if finalized, will not
have disproportionately high and adverse human health or environmental
effects on minority or low-income populations because it increases the
level of environmental protection for all affected populations without
having any disproportionately high and adverse human health or
environmental effects on any population, including any minority or low-
income population. This proposed federal rule limits emissions of
NOX and SO2 from six facilities in Arizona.
List of Subjects in 40 CFR Part 52
Environmental protection, Air pollution control, Incorporation by
reference, Intergovernmental relations, Nitrogen oxides, Sulfur
dioxide, Particulate matter, Reporting and recordkeeping requirements,
Visibility, Volatile organic compounds.
Authority: 42 U.S.C. 7401 et seq.
Dated: January 27, 2014.
Jared Blumenfeld,
Regional Administrator, Region 9.
Part 52, chapter I, title 40 of the Code of Federal Regulations is
proposed to be amended as follows:
PART 52--APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS
0
1. The authority citation for part 52 continues to read as follows:
Authority: 42 U.S.C. 7401 et seq.
Subpart D--Arizona
0
2. Amend Sec. 52.145 by adding paragraphs (i), (j), (k), (l) and (m)
to read as follow:
Sec. 52.145 Visibility protection.
* * * * *
(i) Source-specific federal implementation plan for regional haze
at Nelson Lime Plant--(1) Applicability. This paragraph (i) applies to
the owner/operator of the lime kilns designated as Kiln 1 and Kiln 2 at
the Nelson Lime Plant located in Yavapai County, Arizona.
(2) Definitions. Terms not defined in this paragraph (i)(2) shall
have the meaning given them in the Clean Air Act or EPA's regulations
implementing the Clean Air Act. For purposes of this paragraph (i):
Ammonia injection shall include any of the following: anhydrous
ammonia, aqueous ammonia or urea injection.
Continuous emission monitoring system or CEMS means the equipment
required by this section to sample, analyze, measure, and provide, by
means of readings recorded at least once every 15 minutes (using an
automated data acquisition and handling system (DAHS)), a permanent
record of NOX emissions, SO2 emissions, diluent,
or stack gas volumetric flow rate.
Kiln 1 means rotary kiln 1, as identified in paragraph (i)(1) of
this section.
Kiln 2 means rotary kiln 2, as identified in paragraph (i)(1) of
this section.
Kiln operating day means a 24-hour period between 12 midnight and
the following midnight during which the kiln operates.
Lime product means the product of the lime kiln calcination process
including calcitic lime, dolomitic lime, and dead-burned dolomite.
NOX means nitrogen oxides.
Owner/operator means any person who owns or who operates, controls,
or supervises a kiln identified in paragraph (i)(1) of this section.
SO2 means sulfur dioxide.
Unit means any of the kilns identified in paragraph (i)(1) of this
section.
(3) Emission limitations. The owner/operator of each kiln
identified in paragraph (i)(1) of this section shall not emit or cause
to be emitted pollutants in excess of the following limitations, in
pounds of pollutant per ton of lime product (lb/ton), from any kiln.
Each emission limit shall be based on a rolling 30 kiln-operating day
basis.
------------------------------------------------------------------------
Pollutant emission limit
Kiln ID -------------------------------
NOX SO2
------------------------------------------------------------------------
Kiln 1.................................. 3.80 9.32
Kiln 2.................................. 2.61 9.73
------------------------------------------------------------------------
(4) Compliance dates. (i) The owner/operator of each unit shall
comply with the NOX emissions limitations and other
NOX-related requirements of this paragraph (i) no later than
(three years after date of publication of the final rule in the Federal
Register).
(ii) The owner/operator of each unit shall comply with the
SO2 emissions limitations and other SO2-related
requirements of this paragraph (i) no later than (six months after date
of publication of the final rule in the Federal Register).
(5) Compliance determination--(i) Continuous emission monitoring
system. At all times after the compliance dates specified in paragraph
(i)(4) of this section, the owner/operator of Kiln 1 and 2 shall
maintain, calibrate, and operate a CEMS, in full compliance with the
requirements found at 40 CFR 60.13 and 40 CFR Part 60, Appendices B and
F, to accurately measure the mass emission rate of NOX and
SO2, in pounds per hour, from Kiln 1 and 2. The CEMS shall
be used by the owner/operator to determine compliance with the emission
limitations in paragraph (i)(3) of this section, in combination with
data on actual lime production. The owner/operator must operate the
monitoring system and collect data at all required intervals at all
times that an affected unit is operating, except for periods of
monitoring system malfunctions, repairs associated with monitoring
system malfunctions, and required monitoring system quality assurance
or quality control activities (including, as applicable, calibration
checks and required zero and span adjustments).
(ii) Ammonia consumption monitoring. Upon and after the completion
of installation of ammonia injection on a unit, the owner or operator
shall install, and thereafter maintain and operate, instrumentation to
continuously monitor and record levels of ammonia consumption for that
unit.
(iii) Compliance determination for NOX. Compliance with the
NOX emission limit described in paragraph (i)(3) of this
section shall be determined based on a rolling 30 kiln-operating day
basis. The 30-day rolling NOX emission rate for each kiln
shall be calculated for each kiln operating day in accordance with the
following procedure: Step one, sum the hourly pounds of NOX
emitted for the current kiln operating day and the preceding twenty-
nine (29) kiln operating days, to calculate the total pounds of
NOX emitted over the most recent thirty (30) kiln operating
day period for that kiln; Step two, sum the total lime product, in
tons, produced during the current kiln operating day and the preceding
twenty-nine (29) kiln operating days, to calculate the total lime
product produced over the most
[[Page 9368]]
recent thirty (30) kiln operating day period for that kiln; Step three,
divide the total amount of NOX calculated from Step one by
the total lime product calculated from Step two to calculate the 30-day
rolling NOX emission rate for that kiln. Each 30-day rolling
NOX emission rate shall include all emissions and all lime
product that occur during all periods within any kiln operating day,
including emissions from startup, shutdown and malfunction.
(iv) Compliance determination for SO2. Compliance with the
SO2 emission limit described in paragraph (i)(3) of this
section shall be determined based on a rolling 30 kiln-operating day
basis. The 30-day rolling SO2 emission rate for each kiln
shall be calculated for each kiln operating day in accordance with the
following procedure: Step one, sum the hourly pounds of SO2
emitted for the current kiln operating day and the preceding twenty-
nine (29) kiln operating days, to calculate the total pounds of
SO2 emitted over the most recent thirty (30) kiln operating
day period for that kiln; Step two, sum the total lime product, in
tons, produced during the current kiln operating day and the preceding
twenty-nine (29) kiln operating days, to calculate the total lime
product produced over the most recent thirty (30) kiln operating day
period for that kiln; Step three, divide the total amount of
SO2 calculated from Step one by the total lime product
calculated from Step two to calculate the 30-day rolling SO2
emission rate for that kiln. Each 30-day rolling SO2
emission rate shall include all emissions and all lime product that
occur during all periods within any kiln operating day, including
emissions from startup, shutdown and malfunction.
(6) Recordkeeping. The owner/operator shall maintain the following
records for at least five years:
(i) All CEMS data, including the date, place, and time of sampling
or measurement; parameters sampled or measured; and results.
(ii) All records of lime production.
(iii) Daily 30-day rolling emission rates of NOX and
SO2, when applicable, calculated in accordance with
paragraphs (i)(5)(iii) and (iv) of this section.
(iv) Records of quality assurance and quality control activities
for emissions measuring systems including, but not limited to, any
records required by 40 CFR part 60, appendix F, Procedure 1.
(v) Records of ammonia consumption, as recorded by the
instrumentation required in paragraph (i)(5)(ii) of this section.
(vi) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, CEMS and clinker
production measurement devices.
(vii) Any other records required by 40 CFR part 60, Subpart F, or
40 CFR part 60, Appendix F, Procedure 1.
(7) Reporting. All reports required under this section shall be
submitted by the owner/operator to the Director, Enforcement Division
(Mail Code ENF-2-1), U.S. Environmental Protection Agency, Region 9, 75
Hawthorne Street, San Francisco, California 94105-3901. All reports
required under this section shall be submitted within 30 days after the
applicable compliance date(s) in paragraph (i)(4) of this section and
at least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall submit a report that lists the daily
30-day rolling emission rates for NOX and SO2.
(ii) The owner/operator shall submit excess emissions reports for
NOX and SO2 limits. Excess emissions means
emissions that exceed the emissions limits specified in paragraph
(i)(3) of this section. The reports shall include the magnitude,
date(s), and duration of each period of excess emissions, specific
identification of each period of excess emissions that occurs during
startups, shutdowns, and malfunctions of the unit, the nature and cause
of any malfunction (if known), and the corrective action taken or
preventative measures adopted.
(iii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments.
(iv) The owner/operator shall also submit results of any CEMS
performance tests required by 40 CFR part 60, appendix F, Procedure 1
(Relative Accuracy Test Audits, Relative Accuracy Audits, and Cylinder
Gas Audits).
(v) When no excess emissions have occurred or the CEMS has not been
inoperative, repaired, or adjusted during the reporting period, the
owner/operator shall state such information in the semiannual report.
(8) Notifications. (i) The owner/operator shall notify EPA of
commencement of construction of any equipment which is being
constructed to comply with the NOX emission limits in
paragraph (i)(3) of this section.
(ii) The owner/operator shall submit semiannual progress reports on
construction of any such equipment.
(iii) The owner/operator shall submit notification of initial
startup of any such equipment.
(9) Equipment operations. (i) At all times, including periods of
startup, shutdown, and malfunction, the owner or operator shall, to the
extent practicable, maintain and operate the unit including associated
air pollution control equipment in a manner consistent with good air
pollution control practices for minimizing emissions. Pollution control
equipment shall be designed and capable of operating properly to
minimize emissions during all expected operating conditions.
Determination of whether acceptable operating and maintenance
procedures are being used will be based on information available to the
Regional Administrator which may include, but is not limited to,
monitoring results, review of operating and maintenance procedures, and
inspection of the kiln.
(ii) After completion of installation of ammonia injection on a
unit, the owner or operator shall inject sufficient ammonia to achieve
compliance with NOX emission limits from paragraph (i)(3)
for that unit while preventing excessive ammonia emissions.
(10) Enforcement. Notwithstanding any other provision in this
implementation plan, any credible evidence or information relevant as
to whether the unit would have been in compliance with applicable
requirements if the appropriate performance or compliance test had been
performed, can be used to establish whether or not the owner or
operator has violated or is in violation of any standard or applicable
emission limit in the plan.
(11) Affirmative defense for malfunctions. The following provisions
of the Arizona Administrative Code are incorporated by reference and
made part of this Federal implementation plan:
(i) R-18-2-101, paragraph 65;
(ii) R18-2-310, sections (A), (B), (D) and (E) only; and
(iii) R18-2-310.01.
(j) Source-specific federal implementation plan for regional haze
at H. Wilson Sundt Generating Station--(1) Applicability. This
paragraph (j) applies to the owner and operator of the electricity
generating unit (EGU) designated as Unit I4 at the H. Wilson
[[Page 9369]]
Sundt Generating Station located in Tucson, Pima County, Arizona.
(2) Definitions. Terms not defined in this paragraph (j)(2) shall
have the meaning given them in the Clean Air Act or EPA's regulations
implementing the Clean Air Act. For purposes of this paragraph (j):
Ammonia injection shall include any of the following: anhydrous
ammonia, aqueous ammonia or urea injection.
Boiler operating day means a 24-hour period between 12 midnight and
the following midnight during which any fuel is combusted at any time
in the unit.
Continuous emission monitoring system or CEMS means the equipment
required by 40 CFR Part 75 and this paragraph (j).
MMBtu means one million British thermal units.
NOX means nitrogen oxides.
Owner/operator means any person who owns or who operates, controls,
or supervises the EGU identified in paragraph (j)(1) of this section.
Pipeline natural gas means a naturally occurring fluid mixture of
hydrocarbons as defined in 40 CFR 72.2.
PM means total filterable particulate matter.
PM10 means total particulate matter less than 10 microns
in diameter.
SO2 means sulfur dioxide.
Unit means the EGU identified paragraph (j)(1) of this section.
(3) Emission limitations. The owner/operator of the unit shall not
emit or cause to be emitted pollutants in excess of the following
limitations, in pounds of pollutant per million british thermal units
(lb/MMBtu), from the subject unit.
------------------------------------------------------------------------
Pollutant emission
Pollutant limit
------------------------------------------------------------------------
NOX................................................. 0.36
PM.................................................. 0.030
SO2................................................. 0.23
------------------------------------------------------------------------
(4) Alternative emission limitations. The owner/operator of the
unit may choose to comply with the following limitations in lieu of the
emission limitations listed in paragraph (j)(3).
(i) The owner/operator of the unit shall combust only pipeline
natural gas in the subject unit.
(ii) The owner/operator of the unit shall not emit or cause to be
emitted pollutants in excess of the following limitations, in pounds of
pollutant per million british thermal units (lb/MMBtu), from the
subject unit.
------------------------------------------------------------------------
Pollutant emission
Pollutant limit
------------------------------------------------------------------------
NOX................................................. 0.25
PM10................................................ 0.010
SO2................................................. 0.00064
------------------------------------------------------------------------
(5) Compliance dates. (i) The owner/operator of the unit subject to
this paragraph shall comply with the NOX and SO2
emissions limitations of paragraph (j)(3) of this section no later than
(three years after date of publication of the final rule in the Federal
Register).
(ii) The owner/operator of the unit subject to this paragraph shall
comply with the PM emissions limitations of paragraph (j)(3) of this
section no later than April 16, 2015.
(6) Alternative compliance dates. If the owner/operator chooses to
comply with the emission limits of paragraph (j)(4) of this section in
lieu of paragraph (j)(3) of this section, the owner/operator of the
unit shall comply with the NOX, SO2 and
PM10 emissions limitations of paragraph (j)(4) no later than
December 31, 2017.
(7) Compliance determination--(i) Continuous emission monitoring
system. (A) At all times after the compliance date specified in
paragraph (j)(5)(i) of this section, the owner/operator of the unit
shall maintain, calibrate, and operate a CEMS, in full compliance with
the requirements found at 40 CFR Part 75, to accurately measure
SO2, NOX, diluent, and stack gas volumetric flow
rate from the unit. All valid CEMS hourly data shall be used to
determine compliance with the emission limitations for NOX
and SO2 in paragraph (j)(3) of this section. When the CEMS
is out-of-control as defined by Part 75, that CEMs data shall be
treated as missing data and not used to calculate the emission average.
Each required CEMS must obtain valid data for at least 90 percent of
the unit operating hours, on an annual basis.
(B) The owner/operator of the unit shall comply with the quality
assurance procedures for CEMS found in 40 CFR Part 75. In addition to
these Part 75 requirements, relative accuracy test audits shall be
calculated for both the NOX and SO2 pounds per
hour measurement and the heat input measurement. The CEMs monitoring
data shall not be bias adjusted. Calculations of relative accuracy for
lb/hr of NOX, SO2 and heat input shall be
performed each time the Part 75 CEMS undergo relative accuracy testing.
(ii) Ammonia consumption monitoring. Upon and after the completion
of installation of ammonia injection on the unit, the owner or operator
shall install, and thereafter maintain and operate, instrumentation to
continuously monitor and record levels of ammonia consumption for that
unit.
(iii) Compliance determination for NOX. Compliance with
the NOX emission limit described in paragraph (j)(3) of this
section shall be determined based on a rolling 30 boiler-operating-day
basis. The 30-day rolling NOX emission rate for the unit
shall be calculated for each boiler operating day in accordance with
the following procedure: Step one, sum the hourly pounds of
NOX emitted for the current boiler operating day and the
preceding twenty-nine (29) boiler operating days, to calculate the
total pounds of NOX emitted over the most recent thirty (30)
boiler operating day period for that unit; Step two, sum the total heat
input, in millions of BTU, during the current boiler operating day and
the preceding twenty-nine (29) boiler operating days, to calculate the
total heat input over the most recent thirty (30) boiler operating day
period for that unit; Step three, divide the total amount of
NOX calculated from Step one by the total heat input
calculated from Step two to calculate the 30-day rolling NOX
emission rate, in pounds per million BTU for that unit. Each 30-day
rolling NOX emission rate shall include all emissions and
all heat input that occur during all periods within any boiler
operating day, including emissions from startup, shutdown and
malfunction. If a valid NOX pounds per hour or heat input is
not available for any hour for the unit, that heat input and
NOX pounds per hour shall not be used in the calculation of
the 30-day rolling emission rate.
(iv) Compliance determination for SO2. Compliance with
the SO2 emission limit described in paragraph (j)(3) of this
section shall be determined based on a rolling 30 boiler-operating-day
basis. The 30-day rolling SO2 emission rate for the unit
shall be calculated for each boiler operating day in accordance with
the following procedure: Step one, sum the hourly pounds of
SO2 emitted for the current boiler operating day and the
preceding twenty-nine (29) boiler operating days, to calculate the
total pounds of SO2 emitted over the most recent thirty (30)
boiler operating day period for that unit; Step two, sum the total heat
input, in millions of BTU, during the current boiler operating day and
the preceding twenty-nine (29) boiler operating days, to calculate the
total heat input over the most recent thirty (30) boiler operating day
period for that unit; Step three, divide the total amount of
SO2 calculated from Step one by the total heat input
calculated from
[[Page 9370]]
Step two to calculate the 30-day rolling SO2 emission rate,
in pounds per million BTU for that unit. Each 30-day rolling
SO2 emission rate shall include all emissions and all heat
input that occur during all periods within any boiler operating day,
including emissions from startup, shutdown and malfunction. If a valid
SO2 pounds per hour or heat input is not available for any
hour for the unit, that heat input and SO2 pounds per hour
shall not be used in the calculation of the 30-day rolling emission
rate.
(v) Compliance determination for PM. Compliance with the PM
emission limit described in paragraph (j)(3) shall be determined from
annual performance stack tests. Within sixty (60) days either preceding
or following the compliance deadline specified in paragraph (j)(5)(ii)
of this section, and on at least an annual basis thereafter, the owner/
operator of the unit shall conduct a stack test on the unit to measure
PM using EPA Method 5, in 40 CFR part 60, Appendix A. Each test shall
consist of three runs, with each run at least 120 minutes in duration
and each run collecting a minimum sample of 60 dry standard cubic feet.
Results shall be reported in lb/MMBtu using the calculation in 40 CFR
Part 60 Appendix A, Method 19.
(8) Alternative compliance determination. If the owner/operator
chooses to comply with the emission limits of paragraph (j)(4) of this
section, this paragraph may be used in lieu of paragraph (j)(7) of this
section to demonstrate compliance with the emission limits in paragraph
(j)(4).
(i) Continuous emission monitoring system. (A) At all times after
the compliance date specified in paragraph (j)(6) of this section, the
owner/operator of the unit shall maintain, calibrate, and operate a
CEMS, in full compliance with the requirements found at 40 CFR part 75,
to accurately measure NOX, diluent, and stack gas volumetric
flow rate from the unit. All valid CEMS hourly data shall be used to
determine compliance with the emission limitations for NOX
in paragraph (j)(4) of this section. When the CEMS is out-of-control as
defined by Part 75, that CEMS data shall be treated as missing data and
not used to calculate the emission average. Each required CEMS must
obtain valid data for at least 90 percent of the unit operating hours,
on an annual basis.
(B) The owner/operator of the unit shall comply with the quality
assurance procedures for CEMS found in 40 CFR part 75. In addition to
these part 75 requirements, relative accuracy test audits shall be
calculated for both the NOX pounds per hour measurement and
the heat input measurement. The CEMS monitoring data shall not be bias
adjusted. Calculations of relative accuracy for lb/hr of NOX
and heat input shall be performed each time the Part 75 CEMS undergo
relative accuracy testing.
(ii) Compliance determination for NOX. Compliance with the
NOX emission limit described in paragraph (j)(4) of this
section shall be determined based on a rolling 30 boiler-operating-day
basis. The 30-day rolling NOX emission rate for the unit
shall be calculated for each boiler operating day in accordance with
the following procedure: Step one, sum the hourly pounds of
NOX emitted for the current boiler operating day and the
preceding twenty-nine (29) boiler operating days, to calculate the
total pounds of NOX emitted over the most recent thirty (30)
boiler operating day period for that unit; Step two, sum the total heat
input, in millions of BTU, during the current boiler operating day and
the preceding twenty-nine (29) boiler operating days, to calculate the
total heat input over the most recent thirty (30) boiler operating day
period for that unit; Step three, divide the total amount of
NOX calculated from Step one by the total heat input
calculated from Step two to calculate the 30-day rolling NOX
emission rate, in pounds per million BTU for that unit. Each 30-day
rolling NOX emission rate shall include all emissions and
all heat input that occur during all periods within any boiler
operating day, including emissions from startup and shutdown. If a
valid NOX pounds per hour or heat input is not available for
any hour for the unit, that heat input and NOX pounds per
hour shall not be used in the calculation of the 30-day rolling
emission rate.
(iii) Compliance determination for SO2. Compliance with the
SO2 emission limit for the unit shall be determined from
fuel sulfur documentation demonstrating the use of pipeline natural
gas.
(iv) Compliance determination for PM10. Compliance with the
PM10 emission limit for the unit shall be determined from
performance stack tests. Within sixty (60) days following the
compliance deadline specified in paragraph (j)(6) of this section, and
at the request of the Regional Administrator thereafter, the owner/
operator of the unit shall conduct a stack test on the unit to measure
PM10 using EPA Method 201A and Method 202, per 40 CFR part
51, Appendix M. Each test shall consist of three runs, with each run at
least 120 minutes in duration and each run collecting a minimum sample
of 60 dry standard cubic feet. Results shall be reported in lb/MMBtu
using the calculation in 40 CFR part 60 Appendix A, Method 19.
(9) Recordkeeping. The owner or operator shall maintain the
following records for at least five years:
(i) CEMS data measuring NOX in lb/hr, SO2 in
lb/hr, and heat input rate per hour.
(ii) Daily 30-day rolling emission rates of NOX and
SO2 calculated in accordance with paragraphs (j)(7)(iii) and
(iv) of this section.
(iii) Records of the relative accuracy test for NOX lb/
hr and SO2 lb/hr measurement, and hourly heat input
measurement.
(iv) Records of quality assurance and quality control activities
for emissions systems including, but not limited to, any records
required by 40 CFR part 75.
(v) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, and CEMS.
(vi) Any other records required by 40 CFR part 75.
(vii) Records of ammonia consumption for the unit, as recorded by
the instrumentation required in paragraph (j)(7)(ii) of this section.
(viii) All PM stack test results.
(10) Alternative recordkeeping requirements. If the owner/operator
chooses to comply with the emission limits of paragraph (j)(4) of this
section, the owner/operator shall maintain the records listed in this
paragraph in lieu of the records contained in paragraph (j)(9) of this
section. The owner or operator shall maintain the following records for
at least five years:
(i) CEMS data measuring NOX in lb/hr and heat input rate
per hour.
(ii) Daily 30-day rolling emission rates of NOX
calculated in accordance with paragraph (j)(8)(ii) of this section.
(iii) Records of the relative accuracy test for NOX lb/
hr measurement and hourly heat input measurement.
(iv) Records of quality assurance and quality control activities
for emissions systems including, but not limited to, any records
required by 40 CFR part 75.
(v) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, and CEMS.
(vi) Any other records required by 40 CFR part 75.
(vii) Records sufficient to demonstrate that the fuel for the unit
is pipeline natural gas.
(viii) All PM10 stack test results.
(11) Notifications. (i) By July 31, 2015, the owner/operator shall
notify the Regional Administrator by letter whether it will comply with
the emission limits in paragraph (j)(3) of this section or whether it
will comply
[[Page 9371]]
with the emission limits in paragraph (j)(4) of this section.
(ii) The owner/operator shall notify EPA of commencement of
construction of any equipment which is being constructed to comply with
either the NOX or SO2 emission limits in
paragraph (j)(3) of this section.
(iii) The owner/operator shall submit semiannual progress reports
on construction of any such equipment.
(iv) The owner/operator shall submit notification of initial
startup of any such equipment.
(12) Reporting. All reports required under this section shall be
submitted by the owner/operator to the Director, Enforcement Division
(Mail Code ENF-2-1), U.S. Environmental Protection Agency, Region 9, 75
Hawthorne Street, San Francisco, California 94105-3901. All reports
required under this section shall be submitted within 30 days after the
applicable compliance date(s) in paragraph (j)(5) of this section and
at least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall submit a report that lists the daily
30-day rolling emission rates for NOX and SO2.
(ii) The owner/operator shall submit excess emission reports for
NOX and SO2 limits. Excess emissions means
emissions that exceed the emissions limits specified in paragraph
(j)(3) of this section. Excess emission reports shall include the
magnitude, date(s), and duration of each period of excess emissions,
specific identification of each period of excess emissions that occurs
during startups, shutdowns, and malfunctions of the unit, the nature
and cause of any malfunction (if known), and the corrective action
taken or preventative measures adopted.
(iii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments.
(iv) The owner/operator shall submit the results of any relative
accuracy test audits performed during the two preceding calendar
quarters.
(v) When no excess emissions have occurred or the CEMS has not been
inoperative, repaired, or adjusted during the reporting period, the
owner/operator shall state such information in the semiannual report.
(vi) The owner/operator shall submit results of any PM stack tests
conducted for demonstrating compliance with the PM limit specified in
paragraph (j)(3).
(13) Alternative reporting requirements. If the owner/operator
chooses to comply with the emission limits of paragraph (j)(4) of this
section, the owner/operator shall submit the reports listed in this
paragraph in lieu of the reports contained in paragraph (j)(12) of this
section. All reports required under this paragraph shall be submitted
by the owner/operator to the Director, Enforcement Division (Mail Code
ENF-2-1), U.S. Environmental Protection Agency, Region 9, 75 Hawthorne
Street, San Francisco, California 94105-3901. All reports required
under this paragraph shall be submitted within 30 days after the
applicable compliance date(s) in paragraph (j)(6) of this section and
at least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall submit a report that lists the daily
30-day rolling emission rates for NOX.
(ii) The owner/operator shall submit excess emissions reports for
NOX limits. Excess emissions means emissions that exceed the
emissions limits specified in paragraph (j)(4) of this section. The
reports shall include the magnitude, date(s), and duration of each
period of excess emissions, specific identification of each
period of excess emissions that occurs during startups, shutdowns, and
malfunctions of the unit, the nature and cause of any malfunction (if
known), and the corrective action taken or preventative measures
adopted.
(iii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments.
(iv) The owner/operator shall submit the results of any relative
accuracy test audits performed during the two preceding calendar
quarters.
(v) When no excess emissions have occurred or the CEMS has not been
inoperative, repaired, or adjusted during the reporting period, the
owner/operator shall state such information in the semiannual report.
(vi) The owner/operator shall submit results of any PM10
stack tests conducted for demonstrating compliance with the
PM10 limit specified in paragraph (j)(4) of this section.
(14) Equipment operations. (i) At all times, including periods of
startup, shutdown, and malfunction, the owner or operator shall, to the
extent practicable, maintain and operate the unit including associated
air pollution control equipment in a manner consistent with good air
pollution control practices for minimizing emissions. Pollution control
equipment shall be designed and capable of operating properly to
minimize emissions during all expected operating conditions.
Determination of whether acceptable operating and maintenance
procedures are being used will be based on information available to the
Regional Administrator which may include, but is not limited to,
monitoring results, review of operating and maintenance procedures, and
inspection of the unit.
(ii) After completion of installation of ammonia injection on a
unit, the owner or operator shall inject sufficient ammonia to achieve
compliance with NOX emission limits contained in paragraph
(j)(3) of this section for that unit while preventing excessive ammonia
emissions.
(15) Enforcement. Notwithstanding any other provision in this
implementation plan, any credible evidence or information relevant as
to whether the unit would have been in compliance with applicable
requirements if the appropriate performance or compliance test had been
performed, can be used to establish whether or not the owner or
operator has violated or is in violation of any standard or applicable
emission limit in the plan.
(16) Affirmative defense for malfunctions. The following provisions
of the Arizona Administrative Code are incorporated by reference and
made part of this federal implementation plan:
(i) R-18-2-101, paragraph 65;
(ii) R18-2-310, sections (A), (B), (D) and (E) only; and
(iii) R18-2-310.01.
(k) Source-specific federal implementation plan for regional haze
at Clarkdale Cement Plant and Rillito Cement Plant--(1) Applicability.
This
[[Page 9372]]
paragraph (k) applies to each owner/operator of the following cement
kilns in the state of Arizona: Kiln 4 located at the cement plant in
Clarkdale, Arizona, and Kiln 4 located at the cement plant in Rillito,
Arizona.
(2) Definitions. Terms not defined in this paragraph (k)(2) shall
have the meaning given them in the Clean Air Act or EPA's regulations
implementing the Clean Air Act. For purposes of this paragraph (k):
Ammonia injection shall include any of the following: Anhydrous
ammonia, aqueous ammonia or urea injection.
Continuous emission monitoring system or CEMS means the equipment
required by this section to sample, analyze, measure, and provide, by
means of readings recorded at least once every 15 minutes (using an
automated data acquisition and handling system (DAHS)), a permanent
record of NOX emissions, diluent, or stack gas volumetric
flow rate.
Kiln operating day means a 24-hour period between 12 midnight and
the following midnight during which the kiln operates.
NOX means nitrogen oxides.
Owner/operator means any person who owns or who operates, controls,
or supervises a cement kiln identified in paragraph (k)(1) of this
section.
Unit means a cement kiln identified in paragraph (k)(1) of this
section.
(3) Emissions limitations. The owner/operator of each unit
identified in paragraph (k)(1) of this section shall not emit or cause
to be emitted NOX in excess of the following limitations, in
pounds per ton of clinker produced, based on a rolling 30-kiln
operating day basis.
------------------------------------------------------------------------
NOX emission
Cement Kiln limitation
------------------------------------------------------------------------
Clarkdale Plant, Kiln 4................................ 2.12
Rillito Plant, Kiln 4.................................. 2.67
------------------------------------------------------------------------
(4) Compliance date. The owner/operator of each unit identified in
paragraph (k)(i) of this section shall comply with the NOX
emissions limitations and other NOX-related requirements of
this paragraph (k) no later than (three years after date of publication
of the final rule in the Federal Register).
(5) Compliance determination--(i) Continuous emission monitoring
system. (A) At all times after the compliance date specified in
paragraph (k)(4) of this section, the owner/operator of the unit at the
Clarkdale Plant shall maintain, calibrate, and operate a CEMS, in full
compliance with the requirements found at 40 CFR 60.63(f) and (g), to
accurately measure concentration by volume of NOX, diluent,
and stack gas volumetric flow rate from the in-line/raw mill stack, as
well as the stack gas volumetric flow rate from the coal mill stack.
The CEMS shall be used by the owner/operator to determine compliance
with the emission limitation in paragraph (k)(3) of this section, in
combination with data on actual clinker production. The owner/operator
must operate the monitoring system and collect data at all required
intervals at all times the affected unit is operating, except for
periods of monitoring system malfunctions, repairs associated with
monitoring system malfunctions, and required monitoring system quality
assurance or quality control activities (including, as applicable,
calibration checks and required zero and span adjustments).
(B) At all times after the compliance date specified in paragraph
(k)(4) of this section, the owner/operator of the unit at the Rillito
Plant shall maintain, calibrate, and operate a CEMS, in full compliance
with the requirements found at 40 CFR 60.63(f) and (g), to accurately
measure concentration by volume of NOX, diluent, and stack
gas volumetric flow rate from the unit. The CEMS shall be used by the
owner/operator to determine compliance with the emission limitation in
paragraph (k)(3) of this section, in combination with data on actual
clinker production. The owner/operator must operate the monitoring
system and collect data at all required intervals at all times the
affected unit is operating, except for periods of monitoring system
malfunctions, repairs associated with monitoring system malfunctions,
and required monitoring system quality assurance or quality control
activities (including, as applicable, calibration checks and required
zero and span adjustments).
(ii) Methods. (A) The owner/operator of each unit shall record the
daily clinker production rates.
(B)(1) The owner/operator of each unit shall calculate and record
the 30-kiln operating day average emission rate of NOX, in
lb/ton of clinker produced, as the total of all hourly emissions data
for the cement kiln in the preceding 30-kiln operating days, divided by
the total tons of clinker produced in that kiln during the same 30-day
operating period, using the following equation:
[GRAPHIC] [TIFF OMITTED] TP18FE14.000
Where:
ED = 30 kiln operating day average emission rate of
NOX, lb/ton of clinker;
Ci = Concentration of NOX for hour i, ppm;
Qi = volumetric flow rate of effluent gas for hour i,
where Ci and Qi are on the same basis (either
wet or dry), scf/hr;
Pi = total kiln clinker produced during production hour
i, ton/hr;
k = conversion factor, 1.194 x 10-7 for NOX;
and.
n = number of kiln operating hours over 30 kiln operating days, n =
1 to 720.
(2) For each kiln operating hour for which the owner/operator does
not have at least one valid 15-minute CEMS data value, the owner/
operator must use the average emissions rate (lb/hr) from the most
recent previous hour for which valid data are available. Hourly clinker
production shall be determined by the owner/operator in accordance with
the requirements found at 40 CFR 60.63(b).
(C) At the end of each kiln operating day, the owner/operator shall
calculate and record a new 30-day rolling average emission rate in lb/
ton clinker from the arithmetic average of all valid hourly emission
rates for the current kiln operating day and the previous 29 successive
kiln operating days.
(D) Upon and after the completion of installation of ammonia
injection on a unit, the owner/operator shall install, and thereafter
maintain and operate, instrumentation to continuously monitor and
record levels of ammonia consumption that unit.
(6) Recordkeeping. The owner/operator of each unit shall maintain
the following records for at least five years:
(i) All CEMS data, including the date, place, and time of sampling
or measurement; parameters sampled or measured; and results.
(ii) All records of clinker production.
(iii) Daily 30-day rolling emission rates of NOX,
calculated in accordance with paragraph (k)(5)(ii) of this section.
(iv) Records of quality assurance and quality control activities
for emissions measuring systems including, but not limited to, any
records required by 40 CFR part 60, appendix F, Procedure 1.
(v) Records of ammonia consumption, as recorded by the
instrumentation required in paragraph (k)(5)(ii)(D) of this section.
(vi) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, CEMS and clinker
production measurement devices.
(vii) Any other records required by 40 CFR part 60, Subpart F, or
40 CFR part 60, Appendix F, Procedure 1.
(7) Reporting. All reports required under this section shall be
submitted by the owner/operator to the Director, Enforcement Division
(Mailcode ENF-
[[Page 9373]]
2-1), U.S. Environmental Protection Agency, Region 9, 75 Hawthorne
Street, San Francisco, California 94105-3901. All reports required
under this section shall be submitted within 30 days after the
applicable compliance date in paragraph (k)(4) of this section and at
least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall submit a report that lists the daily
30-day rolling emission rates for NOX.
(ii) The owner/operator shall submit excess emissions reports for
NOX limits. Excess emissions means emissions that exceed the
emissions limits specified in paragraph (k)(3) of this section. The
reports shall include the magnitude, date(s), and duration of each
period of excess emissions, specific identification of each period of
excess emissions that occurs during startups, shutdowns, and
malfunctions of the unit, the nature and cause of any malfunction (if
known), and the corrective action taken or preventative measures
adopted.
(iii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments.
(iv) The owner/operator shall also submit results of any CEMS
performance tests required by 40 CFR part 60, appendix F, Procedure 1
(Relative Accuracy Test Audits, Relative Accuracy Audits, and Cylinder
Gas Audits).
(v) When no excess emissions have occurred or the CEMS has not been
inoperative, repaired, or adjusted during the reporting period, the
owner/operator shall state such information in the reports required by
paragraph (k)(7)(ii) of this section.
(8) Notifications. (i) The owner/operator shall submit notification
of commencement of construction of any equipment which is being
constructed to comply with the NOX emission limits in
paragraph (k)(3) of this section.
(ii) The owner/operator shall submit semiannual progress reports on
construction of any such equipment.
(iii) The owner/operator shall submit notification of initial
startup of any such equipment.
(9) Equipment operation. (i) At all times, including periods of
startup, shutdown, and malfunction, the owner or operator shall, to the
extent practicable, maintain and operate the unit including associated
air pollution control equipment in a manner consistent with good air
pollution control practices for minimizing emissions. Pollution control
equipment shall be designed and capable of operating properly to
minimize emissions during all expected operating conditions.
Determination of whether acceptable operating and maintenance
procedures are being used will be based on information available to the
Regional Administrator which may include, but is not limited to,
monitoring results, review of operating and maintenance procedures, and
inspection of the unit.
(ii) After completion of installation of ammonia injection on a
unit, the owner or operator shall inject sufficient ammonia to achieve
compliance with NOX emission limits from paragraph (k)(3)
for that unit while preventing excessive ammonia emissions.
(10) Enforcement. Notwithstanding any other provision in this
implementation plan, any credible evidence or information relevant as
to whether the unit would have been in compliance with applicable
requirements if the appropriate performance or compliance test had been
performed, can be used to establish whether or not the owner or
operator has violated or is in violation of any standard or applicable
emission limit in the plan.
(11) Affirmative defense for malfunctions. The following provisions
of the Arizona Administrative Code are incorporated by reference and
made part of this Federal implementation plan:
(i) R-18-2-101, paragraph 65;
(ii) R18-2-310, sections (A), (B), (D) and (E) only; and
(iii) R18-2-310.01.
(l) Source-specific federal implementation plan for regional haze
at Hayden Copper Smelter--(1) Applicability. This paragraph (l) applies
to each owner/operator of each batch copper converter and anode
furnaces 1 and 2 at the copper smelting plant located
in Hayden, Gila County, Arizona.
(2) Definitions. Terms not defined in this paragraph (l)(2) shall
have the meaning given them in the Clean Air Act or EPA's regulations
implementing the Clean Air Act. For purposes of this paragraph (l):
Anode furnace means a furnace in which molten blister copper is
refined through introduction of a reducing agent such as natural gas.
Batch copper converter means a Pierce-Smith converter or Hoboken
converter in which copper matte is oxidized to form blister copper by a
process that is performed in discrete batches using a sequence of
charging, blowing, skimming, and pouring.
Blister copper means an impure form of copper, typically between 98
and 99 percent pure copper that is the output of the converters.
Calendar day means a 24 hour period that begins and ends at
midnight, local standard time.
Continuous emission monitoring system or CEMS means the equipment
required by this section to sample, analyze, measure, and provide, by
means of readings recorded at least once every 15 minutes (using an
automated data acquisition and handling system (DAHS)), a permanent
record of SO2 emissions, other pollutant emissions, diluent,
or stack gas volumetric flow rate.
Copper matte means a material predominately composed of copper and
iron sulfides produced by smelting copper ore concentrates.
NOX means nitrogen oxides.
Owner/operator means any person who owns or who operates, controls,
or supervises the equipment identified in paragraph (l)(1) of this
section.
SO2 means sulfur dioxide.
(3) Emission capture. (i) The owner/operator of the batch copper
converters identified in paragraph (l)(1) of this section must operate
a capture system that has been designed to maximize collection of
process off gases vented from each converter. At all times when one or
more converters are blowing, you must operate the capture system
consistent with a written operation and maintenance plan that has been
prepared according to the requirements in 40 CFR 63.1447(b) and
approved by EPA within 180 days of the compliance date in paragraph
(l)(5) of this section. The capture system must include a primary
capture system as described in 40 CFR 63.1444(d)(2) and a secondary
hood as described in 40 CFR 63.1444(d)(2). (ii) The operation of the
batch copper converters and secondary hood shall be optimized to
capture the maximum amount of process off gases vented from each
converter at all times.
(4) Emission limitations and work practice standards. (i)
SO2 emissions collected by the capture system required by
paragraph (l)(3) of this section must be controlled by one or more
control devices and reduced by at least 99.81
[[Page 9374]]
percent, based on a 30-day rolling average.
(ii) The owner/operator must not cause or allow to be discharged to
the atmosphere from any primary capture system required by paragraph
(l)(3) off-gas that contains nonsulfuric acid particulate matter in
excess of 6.2 mg/dscm as measured using the test methods specified in
40 CFR 63.1450(b).
(iii) The owner/operator must not cause or allow to be discharged
to the atmosphere from any secondary capture system required by
paragraph (l)(3) of this section off-gas that contains particulate
matter in excess of 23 mg/dscm as measured using the test methods
specified in 40 CFR 63.1450(a).
(iv) Total NOX emissions from anode furnaces 1
and 2 and the batch copper converters shall not exceed 40 tons
per 12-continuous month period.
(v) Anode furnaces 1 and 2 shall only be charged
with blister copper or higher purity copper.
(5) Compliance dates. The owner/operator of each batch copper
converter identified in paragraph (l)(1) of this section shall comply
with the emissions limitations and other requirements of this section
no later than (three years after date of publication of the final rule
in the Federal Register).
(6) Compliance determination--(i) Continuous emission monitoring
system. At all times after the compliance date specified in paragraph
(e) of this section, the owner/operator of each batch copper converter
identified in paragraph (l)(1) of this section shall maintain,
calibrate, and operate a CEMS, in full compliance with the requirements
found at 40 CFR 60.13 and 40 CFR part 60, Appendices B and F, to
accurately measure the mass emission rate in pounds per hour of
SO2 emissions entering each control device used to control
emissions from the converters, and venting from the converters to the
atmosphere after passing through a control device or an uncontrolled
bypass stack. The CEMS shall be used by the owner/operator to determine
compliance with the emission limitation in paragraph (l)(4) of this
plan. The owner/operator must operate the monitoring system and collect
data at all required intervals at all times that an affected unit is
operating, except for periods of monitoring system malfunctions,
repairs associated with monitoring system malfunctions, and required
monitoring system quality assurance or quality control activities
(including, as applicable, calibration checks and required zero and
span adjustments).
(ii) Compliance determination for SO2. The 30-day rolling
SO2 emission control efficiency for the converters shall be
calculated for each calendar day in accordance with the following
procedure: Step one, sum the hourly pounds of SO2 vented to
each uncontrolled bypass stack and to each control device used to
control emissions from the converters for the current calendar day and
the preceding twenty-nine (29) calendar days, to calculate the total
pounds of pre-control SO2 emissions over the most recent
thirty (30) calendar day period; Step two, sum the hourly pounds of
SO2 vented to each uncontrolled bypass stack and emitted
from the release point of each control device used to control emissions
from the converters for the current calendar day and the preceding
twenty-nine (29) calendar days, to calculate the total pounds of post-
control SO2 emissions over the most recent thirty (30)
calendar day period; Step three, divide the total amount of post-
control SO2 emissions calculated from Step two by the total
amount of pre-control SO2 emissions calculated from Step
one, subtract the resulting quotient from one, and multiply the
difference by 100 percent to calculate the 30-day rolling
SO2 emission control efficiency as a percentage.
(iii) Compliance determination for nonsulfuric acid particulate
matter. Compliance with the emission limit for nonsulfuric acid
particulate matter in paragraph (l)(4)(ii) of this section shall be
demonstrated by the procedures in 40 CFR 63.1451(b) and 40 CFR
63.1453(a)(2).
(iv) Compliance determination for particulate matter. Compliance
with the emission limit for particulate matter in paragraph (l)(4)(iii)
of this section shall be demonstrated by the procedures in 40 CFR
63.1451(a) and 40 CFR 63.1453(a)(1).
(v) Compliance determination for NOX. Compliance with the emission
limit for NOX in paragraph (l)(4)(iv) of this section shall
be demonstrated by monitoring natural gas consumption in each of the
units identified in paragraph (l)(1) of this section for each calendar
day. At the end of each calendar month, the owner/operator shall
calculate 12-consecutive month NOX emissions by multiplying
the daily natural gas consumption rates for each unit by an approved
emission factor and adding the sums for all units over the previous 12-
consecutive month period.
(7) Alternative compliance determination for sulfuric acid plants.
If the owner/operator uses one or more double contact acid plants to
control SO2 from the batch copper converters identified in
paragraph (l)(1) of this section, this paragraph may be used to
demonstrate compliance with the emission limit in paragraph (l)(4)(i)
of this section.
(i) Continuous emission monitoring system. At all times after the
compliance date specified in paragraph (l)(5) of this section, the
owner/operator of each batch copper converter identified in paragraph
(l)(1) of this section shall maintain, calibrate, and operate a CEMS,
in full compliance with the requirements found at 40 CFR 60.13 and 40
CFR part 60, Appendices B and F, to accurately measure the mass
emission rate in pounds per hour of SO2 emissions venting
from the converters to the atmosphere after passing through a control
device or an uncontrolled bypass stack. The CEMS shall be used by the
owner/operator to determine compliance with the emission limitation in
paragraph (l)(4) of this section. The owner/operator must operate the
monitoring system and collect data at all required intervals at all
times that an affected unit is operating, except for periods of
monitoring system malfunctions, repairs associated with monitoring
system malfunctions, and required monitoring system quality assurance
or quality control activities (including, as applicable, calibration
checks and required zero and span adjustments).
(ii) Daily sulfuric acid production monitoring. At all times after
the compliance date specified in paragraph (l)(5) of this section, the
owner/operator of each batch copper converter subject to this section
shall monitor and maintain records of sulfuric acid production for each
calendar day.
(iii) Compliance determination for SO2. The 30-day rolling
SO2 emission rate for the converters shall be calculated for
each calendar day in accordance with the following procedure: Step one,
sum the hourly pounds of SO2 vented to each uncontrolled
bypass stack and emitted from the release point of each double contact
acid plant used to control emissions from the converters for the
current calendar day and the preceding twenty-nine (29) calendar days,
to calculate the total pounds of SO2 emissions over the most
recent thirty (30) calendar day period; Step two, sum the total
sulfuric acid production in tons of pure sulfuric acid for the current
calendar day and the preceding twenty-nine (29) calendar days, to
calculate the total tons of sulfuric acid production over the most
recent thirty (30) calendar day period; Step three, divide the total
amount of SO2 emissions calculated from Step one by the
total tons of sulfuric acid production calculated from Step one to
calculate the 30-day rolling
[[Page 9375]]
SO2 emission rate in lbs-SO2 per ton of sulfuric
acid. An emission rate of 4.06 or lower shall be deemed to be in
compliance with the emission limit in paragraph (i)(4) of this section.
(8) Capture system monitoring. For each operating limit established
under the capture system operation and maintenance plan required by
paragraph (l)(4) of this section, the owner/operator must install,
operate, and maintain an appropriate monitoring device according to the
requirements in 40 CFR 63.1452(a)(1) though (6) to measure and record
the operating limit value or setting at all times the required capture
system is operating. Dampers that are manually set and remain in the
same position at all times the capture system is operating are exempted
from these monitoring requirements.
(9) Recordkeeping. The owner/operator shall maintain the following
records for at least five years:
(i) All CEMS data, including the date, place, and time of sampling
or measurement; parameters sampled or measured; and results.
(ii) Records of quality assurance and quality control activities
for emissions measuring systems including, but not limited to, any
records required by 40 CFR part 60, appendix F, Procedure 1.
(iii) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, and CEMS.
(iv) Any other records required by 40 CFR part 60, Subpart F, or 40
CFR part 60, Appendix F, Procedure 1.
(v) Records of all monitoring required by paragraph (l)(8) of this
section.
(vi) Records of daily sulfuric acid production in tons per day of
pure sulfuric acid if the owner/operator chooses to use the alternative
compliance determination method in paragraph (l)(7) of this section.
(vii) Records of daily natural gas consumption in each units
identified in paragraph (l)(1) and all calculations performed to
demonstrate compliance with the limit in paragraph (l)(4)(iv).
(10) Reporting. All reports required under this section shall be
submitted by the owner/operator to the Director, Enforcement Division
(Mail Code ENF-2-1), U.S. Environmental Protection Agency, Region 9, 75
Hawthorne Street, San Francisco, California 94105-3901. All reports
required under this section shall be submitted within 30 days after the
applicable compliance date in paragraph (l)(5) of this section and at
least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall promptly submit excess emissions
reports for the SO2 limit. Excess emissions means emissions
that exceed the emissions limit specified in paragraph (d) of this
section. The reports shall include the magnitude, date(s), and duration
of each period of excess emissions, specific identification of each
period of excess emissions that occurs during startups, shutdowns, and
malfunctions of the unit, the nature and cause of any malfunction (if
known), and the corrective action taken or preventative measures
adopted. For the purpose of this paragraph, promptly shall mean within
30 days after the end of the month in which the excess emissions were
discovered.
(ii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments. The owner/
operator shall submit reports semiannually.
(iii) The owner/operator shall also submit results of any CEMS
performance tests required by 40 CFR part 60, appendix F, Procedure 1
(Relative Accuracy Test Audits, Relative Accuracy Audits, and Cylinder
Gas Audits).
(iv) When no excess emissions have occurred or the CEMS has not
been inoperative, repaired, or adjusted during the reporting period,
the owner/operator shall state such information in the semiannual
report.
(v) When performance testing is required to determine compliance
with an emission limit in paragraph (l)(4) of this section, the owner/
operator shall submit test reports as specified in 40 CFR part 63,
subpart A.
(11) Notifications. (i) The owner/operator shall notify EPA of
commencement of construction of any equipment which is being
constructed to comply with the capture or emission limits in paragraph
(l)(3) or (4) of this section.
(ii) The owner/operator shall submit semiannual progress reports on
construction of any such equipment.
(iii) The owner/operator shall submit notification of initial
startup of any such equipment.
(12) Equipment operations. At all times, including periods of
startup, shutdown, and malfunction, the owner or operator shall, to the
extent practicable, maintain and operate the unit including associated
air pollution control equipment in a manner consistent with good air
pollution control practices for minimizing emissions. Pollution control
equipment shall be designed and capable of operating properly to
minimize emissions during all expected operating conditions.
Determination of whether acceptable operating and maintenance
procedures are being used will be based on information available to the
Regional Administrator which may include, but is not limited to,
monitoring results, review of operating and maintenance procedures, and
inspection of the unit.
(13) Enforcement. Notwithstanding any other provision in this
implementation plan, any credible evidence or information relevant as
to whether the unit would have been in compliance with applicable
requirements if the appropriate performance or compliance test had been
performed, can be used to establish whether or not the owner or
operator has violated or is in violation of any standard or applicable
emission limit in the plan.
(14) Affirmative defense for malfunctions. The following provisions
of the Arizona Administrative Code are incorporated by reference and
made part of this Federal implementation plan:
(i) R-18-2-101, paragraph 65;
(ii) R18-2-310, sections (A), (B), (D) and (E) only; and
(iii) R18-2-310.01.
(m) Source-specific federal implementation plan for regional haze
at Miami Copper Smelter--(1) Applicability. This paragraph (m) applies
to each owner/operator of each batch copper converter and the electric
furnace at the copper smelting plant located in Hayden, Gila County,
Arizona.
(2) Definitions. Terms not defined in this paragraph (m)(2) shall
have the meaning given them in the Clean Air Act or EPA's regulations
implementing the Clean Air Act. For purposes of this paragraph (m):
Batch copper converter means a Pierce-Smith converter or Hoboken
converter in which copper matte is oxidized to form blister copper by a
process that is performed in discrete batches using a sequence of
charging, blowing, skimming, and pouring.
Calendar day means a 24 hour period that begins and ends at
midnight, local standard time.
[[Page 9376]]
Continuous emission monitoring system or CEMS means the equipment
required by this section to sample, analyze, measure, and provide, by
means of readings recorded at least once every 15 minutes (using an
automated data acquisition and handling system (DAHS)), a permanent
record of SO2 emissions, other pollutant emissions, diluent,
or stack gas volumetric flow rate.
Copper matte means a material predominately composed of copper and
iron sulfides produced by smelting copper ore concentrates.
Electric furnace means a furnace in which copper matte and slag are
heated by electrical resistance without the mechanical introduction of
air or oxygen.
NOX means nitrogen oxides.
Owner/operator means any person who owns or who operates, controls,
or supervises the equipment identified in paragraph (m)(1) of this
section.
Slag means the waste material consisting primarily of iron sulfides
separated from copper matte during the smelting and refining of copper
ore concentrates.
SO2 means sulfur dioxide.
(3) Emission capture. (i)The owner/operator of the batch copper
converters identified in paragraph (m)(1) of this section must operate
a capture system that has been designed to maximize collection of
process off gases vented from each converter. At all times when one or
more converters are blowing, you must operate the capture system
consistent with a written operation and maintenance plan that has been
prepared according to the requirements in 40 CFR 63.1447(b) and
approved by EPA within 180 days of the compliance date in paragraph
(m)(5) of this section. The capture system must include a primary
capture system as described in 40 CFR 63.1444(d)(3) and a secondary
hood as described in 40 CFR 63.1444(d)(2). (ii) The operation of the
batch copper converters and secondary hood shall be optimized to
capture the maximum amount of process off gases vented from each
converter at all times.
(4) Emission limitations and work practice standards. (i)
SO2 emissions collected by the capture system required by
paragraph (m)(3) of this section must be controlled by one or more
control devices and reduced by at least 99.7 percent, based on a 30-day
rolling average.
(ii) Total NOX emissions the electric furnace and the
batch copper converters shall not exceed 40 tons per 12-continuous
month period.
(iii) The owner/operator shall not actively aerate the electric
furnace.
(5) Compliance dates. The owner/operator of each batch copper
converter identified in paragraph (m)(1) of this section shall comply
with the emissions limitations and other requirements of this section
no later than (three years after date of publication of the final rule
in the Federal Register).
(6) Compliance determination--(i) Continuous emission monitoring
system. At all times after the compliance date specified in paragraph
(e) of this section, the owner/operator of each batch copper converter
identified in paragraph (m)(1) of this section shall maintain,
calibrate, and operate a CEMS, in full compliance with the requirements
found at 40 CFR 60.13 and 40 CFR part 60, Appendices B and F, to
accurately measure the mass emission rate in pounds per hour of
SO2 emissions entering each control device used to control
emissions from the converters, and venting from the converters to the
atmosphere after passing through a control device or an uncontrolled
bypass stack. The CEMS shall be used by the owner/operator to determine
compliance with the emission limitation in paragraph (m)(4) of this
section. The owner/operator must operate the monitoring system and
collect data at all required intervals at all times that an affected
unit is operating, except for periods of monitoring system
malfunctions, repairs associated with monitoring system malfunctions,
and required monitoring system quality assurance or quality control
activities (including, as applicable, calibration checks and required
zero and span adjustments).
(ii) Compliance determination for SO2. The 30-day rolling
SO2 emission control efficiency for the converters shall be
calculated for each calendar day in accordance with the following
procedure: Step one, sum the hourly pounds of SO2 vented to
each uncontrolled bypass stack and to each control device used to
control emissions from the converters for the current calendar day and
the preceding twenty-nine (29) calendar days, to calculate the total
pounds of pre-control SO2 emissions over the most recent
thirty (30) calendar day period; Step two, sum the hourly pounds of
SO2 vented to each uncontrolled bypass stack and emitted
from the release point of each control device used to control emissions
from the converters for the current calendar day and the preceding
twenty-nine (29) calendar days, to calculate the total pounds of post-
control SO2 emissions over the most recent thirty (30)
calendar day period; Step three, divide the total amount of post-
control SO2 emissions calculated from Step two by the total
amount of pre-control SO2 emissions calculated from Step
one, subtract the resulting quotient from one, and multiply the
difference by 100 percent to calculate the 30-day rolling
SO2 emission control efficiency as a percentage.
(iii) Compliance determination for NOX. Compliance with the
emission limit for NOX in paragraph (m)(4)(ii) of this
section shall be demonstrated by monitoring natural gas consumption in
each of the units identified in paragraph (m)(1) of this section for
each calendar day. At the end of each calendar month, the owner/
operator shall calculate monthly and 12-consecutive month
NOX emissions by multiplying the daily natural gas
consumption rates for each unit by an approved emission factor and
adding the sums for all units over the previous 12-consecutive month
period.
(7) Alternative compliance determination for sulfuric acid plants.
If the owner/operator uses one or more double contact acid plants to
control SO2 from the batch copper converters identified in
paragraph (m)(1) of this section, this paragraph may be used to
demonstrate compliance with the emission limit in paragraph (m)(4)(i)
of this section.
(i) Continuous emission monitoring system. At all times after the
compliance date specified in paragraph (m)(5) of this section, the
owner/operator of each batch copper converter identified in paragraph
(m)(1) of this section shall maintain, calibrate, and operate a CEMS,
in full compliance with the requirements found at 40 CFR 60.13 and 40
CFR part 60, Appendices B and F, to accurately measure the mass
emission rate in pounds per hour of SO2 emissions venting
from the converters to the atmosphere after passing through a control
device or an uncontrolled bypass stack. The CEMS shall be used by the
owner/operator to determine compliance with the emission limitation in
paragraph (m)(4) of this section. The owner/operator must operate the
monitoring system and collect data at all required intervals at all
times that an affected unit is operating, except for periods of
monitoring system malfunctions, repairs associated with monitoring
system malfunctions, and required monitoring system quality assurance
or quality control activities (including, as applicable, calibration
checks and required zero and span adjustments).
(ii) Daily sulfuric acid production monitoring. At all times after
the compliance date specified in paragraph (m)(5) of this section, the
owner/operator of each batch copper converter subject to this section
shall monitor and
[[Page 9377]]
maintain records of sulfuric acid production for each calendar day.
(iii) Compliance determination for SO2. The 30-day rolling
SO2 emission rate for the converters shall be calculated for
each calendar day in accordance with the following procedure: Step one,
sum the hourly pounds of SO2 vented to each uncontrolled
bypass stack and emitted from the release point of each double contact
acid plant used to control emissions from the converters for the
current calendar day and the preceding twenty-nine (29) calendar days,
to calculate the total pounds of SO2 emissions over the most
recent thirty (30) calendar day period; Step two, sum the total
sulfuric acid production in tons of pure sulfuric acid for the current
calendar day and the preceding twenty-nine (29) calendar days, to
calculate the total tons of sulfuric acid production over the most
recent thirty (30) calendar day period; Step three, divide the total
amount of SO2 emissions calculated from Step one by the
total tons of sulfuric acid production calculated from Step one to
calculate the 30-day rolling SO2 emission rate in lbs-
SO2 per ton of sulfuric acid. An emission rate of 4.06 or
lower shall be deemed to be in compliance with the emission limit in
paragraph (i)(4) of this section.
(8) Capture system monitoring. For each operating limit established
under the capture system operation and maintenance plan required by
paragraph (m)(4) of this section, the owner/operator must install,
operate, and maintain an appropriate monitoring device according to the
requirements in 40 CFR 63.1452(a)(1) though (6) to measure and record
the operating limit value or setting at all times the required capture
system is operating. Dampers that are manually set and remain in the
same position at all times the capture system is operating are exempted
from these monitoring requirements.
(9) Recordkeeping. The owner/operator shall maintain the following
records for at least five years:
(i) All CEMS data, including the date, place, and time of sampling
or measurement; parameters sampled or measured; and results.
(ii) Records of quality assurance and quality control activities
for emissions measuring systems including, but not limited to, any
records required by 40 CFR part 60, appendix F, Procedure 1.
(iii) Records of all major maintenance activities conducted on
emission units, air pollution control equipment, and CEMS.
(iv) Any other records required by 40 CFR part 60, Subpart F, or 40
CFR part 60, Appendix F, Procedure 1.
(v) Records of all monitoring required by paragraph (m)(8) of this
section.
(vi) Records of daily sulfuric acid production in tons per day of
pure sulfuric acid if the owner/operator chooses to use the alternative
compliance determination method in paragraph (m)(7) of this section.
(vii) Records of daily natural gas consumption in each units
identified in paragraph (m)(1) and all calculations performed to
demonstrate compliance with the limit in paragraph (m)(4)(iv).
(10) Reporting. All reports required under this section shall be
submitted by the owner/operator to the Director, Enforcement Division
(Mail Code ENF-2-1), U.S. Environmental Protection Agency, Region 9, 75
Hawthorne Street, San Francisco, California 94105-3901. All reports
required under this section shall be submitted within 30 days after the
applicable compliance date in paragraph (m)(5) of this section and at
least semiannually thereafter, within 30 days after the end of a
semiannual period. The owner/operator may submit reports more
frequently than semiannually for the purposes of synchronizing reports
required under this section with other reporting requirements, such as
the title V monitoring report required by 40 CFR 70.6(a)(3)(iii)(A),
but at no point shall the duration of a semiannual period exceed six
months.
(i) The owner/operator shall promptly submit excess emissions
reports for the SO2 limit. Excess emissions means emissions
that exceed the emissions limit specified in paragraph (d) of this
section. The reports shall include the magnitude, date(s), and duration
of each period of excess emissions, specific identification of each
period of excess emissions that occurs during startups, shutdowns, and
malfunctions of the unit, the nature and cause of any malfunction (if
known), and the corrective action taken or preventative measures
adopted. For the purpose of this paragraph, promptly shall mean within
30 days after the end of the month in which the excess emissions were
discovered.
(ii) The owner/operator shall submit CEMS performance reports, to
include dates and duration of each period during which the CEMS was
inoperative (except for zero and span adjustments and calibration
checks), reason(s) why the CEMS was inoperative and steps taken to
prevent recurrence, and any CEMS repairs or adjustments. The owner/
operator shall submit reports semiannually.
(iii) The owner/operator shall also submit results of any CEMS
performance tests required by 40 CFR part 60, appendix F, Procedure 1
(Relative Accuracy Test Audits, Relative Accuracy Audits, and Cylinder
Gas Audits).
(iv) When no excess emissions have occurred or the CEMS has not
been inoperative, repaired, or adjusted during the reporting period,
the owner/operator shall state such information in the semiannual
report.
(v) When performance testing is required to determine compliance
with an emission limit in paragraph (m)(4) of this section, the owner/
operator shall submit test reports as specified in 40 CFR part 63,
subpart A.
(11) Notifications. (i) The owner/operator shall notify EPA of
commencement of construction of any equipment which is being
constructed to comply with the capture or emission limits in paragraph
(m)(3) or (4) of this section.
(ii) The owner/operator shall submit semiannual progress reports on
construction of any such equipment.
(iii) The owner/operator shall submit notification of initial
startup of any such equipment.
(12) Equipment operations. At all times, including periods of
startup, shutdown, and malfunction, the owner or operator shall, to the
extent practicable, maintain and operate the unit including associated
air pollution control equipment in a manner consistent with good air
pollution control practices for minimizing emissions. Pollution control
equipment shall be designed and capable of operating properly to
minimize emissions during all expected operating conditions.
Determination of whether acceptable operating and maintenance
procedures are being used will be based on information available to the
Regional Administrator which may include, but is not limited to,
monitoring results, review of operating and maintenance procedures, and
inspection of the unit.
(13) Enforcement. Notwithstanding any other provision in this
implementation plan, any credible evidence or information relevant as
to whether the unit would have been in compliance with applicable
requirements if the appropriate performance or compliance test had been
performed, can be used to establish whether or not the owner or
operator has violated or is in violation of any standard or applicable
emission limit in the plan.
[[Page 9378]]
(14) Affirmative defense for malfunctions. The following provisions
of the Arizona Administrative Code are incorporated by reference and
made part of this federal implementation plan:
(i) R-18-2-101, paragraph 65;
(ii) R18-2-310, sections (A), (B), (D) and (E) only; and
(iii) R18-2-310.01.
[FR Doc. 2014-02714 Filed 2-14-14; 8:45 am]
BILLING CODE 6560-50-P