[Federal Register Volume 79, Number 107 (Wednesday, June 4, 2014)]
[Proposed Rules]
[Pages 32197-32199]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-12973]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0072; Directorate Identifier 2013-NE-04-AD]
RIN 2120-AA64
Airworthiness Directives; Pratt & Whitney Division Turbofan
Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to supersede airworthiness directive (AD) 2013-15-
09, which applies to all Pratt & Whitney Division (PW) PW4074, PW4074D,
PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engine models
with certain second-stage high-pressure turbine (HPT) air seals,
installed. AD 2013-15-09 currently requires initial and repetitive
inspections for cracks in second-stage HPT air seals. Since we issued
AD 2013-15-09, we received reports of cracking in the original location
on two additional part numbers (P/Ns) as well as reports of through-
cracks in a new location in the second-stage HPT air seal. PW has
developed a redesigned second-stage HPT air seal that addresses the
cracking condition in both locations. This proposed AD would expand the
applicability of AD 2013-15-09 to include additional P/Ns, require
replacement of the mating hardware if the second-stage HPT air seal is
found with a through-crack, and add mandatory terminating action to the
repetitive inspections. We are proposing this AD to prevent failure of
the second-stage HPT air seal, which could lead to uncontained engine
failure and damage to the airplane.
DATES: We must receive comments on this proposed AD by August 4, 2014.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Pratt & Whitney Division, 400 Main St., East Hartford, CT 06108; phone:
(860) 565-8770; fax: (860) 565-4503. You may view this service
information at the FAA, Engine & Propeller Directorate, 12 New England
Executive Park, Burlington, MA. For information on the availability of
this material at the FAA, call (781) 238-7125.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2013-
0072; or in person at the Docket Management Facility between 9 a.m. and
5 p.m., Monday through Friday, except Federal holidays. The AD docket
contains this proposed AD, the regulatory evaluation, any comments
received, and other information. The street address for the Docket
Office (phone: (800) 647-5527) is in the ADDRESSES section. Comments
will be available in the AD docket shortly after receipt.
[[Page 32198]]
FOR FURTHER INFORMATION CONTACT: James Gray, Aerospace Engineer, Engine
Certification Office, FAA, Engine & Propeller Directorate, 12 New
England Executive Park, Burlington, MA 01803; phone: (781) 238-7742;
fax: (781) 238-7199; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2013-0072;
Directorate Identifier 2013-NE-04-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
On July 19, 2013, we issued AD 2013-15-09, Amendment 39-17525 (78
FR 49111, August 13, 2013), (``AD 2013-15-09''), for all PW PW4074,
PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engine
models with second-stage HPT air seal, P/N 54L041, installed. AD 2013-
15-09 requires initial and repetitive inspections for cracks in second-
stage HPT air seals and replacement of air seals that fail inspection.
AD 2013-15-09 resulted from the discovery of cracks in second-stage HPT
air seals. We issued AD 2013-15-09 to prevent failure of the second-
stage HPT air seal, which could lead to uncontained engine failure and
damage to the airplane.
Actions Since AD 2013-15-09 Was Issued
Since we issued AD 2013-15-09, we received multiple reports of
through-cracks in a different location on second-stage HPT air seal, P/
N 50L041, and reports of cracking in the original location in two
additional second-stage HPT air seal P/Ns, 50L960 and 50L976. The
cracking in the two additional P/Ns requires that they be added to the
applicability of this proposed AD. PW has developed a redesigned
second-stage HPT air seal that corrects the cracking condition in both
locations.
The new cracking location in the second-stage HPT air seal, P/N
50L041, is in the front forward fillet radius. PW determined that
through-cracks in the front forward fillet radius increase the stresses
in the mating hardware in the HPT rotor and that increased stress
reduces the life of the first-stage HPT hub, second-stage HPT hub, and
second-stage HPT blade retaining plate. Therefore, the first-stage HPT
hub, second-stage HPT hub, and second-stage HPT blade retaining plate
must be removed from service if the second-stage HPT air seal, P/N
50L041, is found with a through-crack.
Relevant Service Information
We reviewed PW Alert Service Bulletin (ASB) No. PW4G-112-A72-330,
Revision 2, dated July 11, 2013, which describes procedures for
inspecting the second-stage HPT air seal for cracks and PW Service
Bulletin (SB) No. PW4G-112-72-332, Revision 2, dated April 9, 2014,
which describes procedures for replacing the second-stage HPT air seal.
FAA's Determination
We are proposing this AD because we evaluated all the relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the same type design.
Proposed AD Requirements
This proposed AD would expand the population of affected P/Ns,
require removal from service of two newly identified P/Ns, require
replacement of the mating hardware if the second-stage HPT air seal is
found with a through-crack, and add mandatory terminating action to the
repetitive inspection requirements.
Costs of Compliance
We estimate that this proposed AD would affect 116 engines
installed on airplanes of U.S. registry. We also estimate that it would
take about 5 hours to perform the inspection required by this proposed
AD. The average labor rate is $85 per hour. We estimate that two
engines will also require replacement of the first-stage HPT hub,
second-stage HPT hub, and second-stage HPT blade retaining plate. We
estimate that parts would cost about $698,920 per engine. Based on
these figures, we estimate the total cost of this proposed AD to U.S.
operators to be $23,420,020.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska to the extent
that it justifies making a regulatory distinction, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
[[Page 32199]]
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing airworthiness directive (AD)
2013-15-09, Amendment 39-17525 (78 FR 49111, August 13, 2013), and
adding the following new AD:
Pratt & Whitney Division: Docket No. FAA-2013-0072; Directorate
Identifier 2013-NE-04-AD.
(a) Comments Due Date
The FAA must receive comments on this AD action by August 4,
2014.
(b) Affected ADs
This AD supersedes AD 2013-15-09, Amendment 39-17525 (78 FR
49111, August 13, 2013).
(c) Applicability
This AD applies to all Pratt & Whitney Division (PW) PW4074,
PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan
engine models with second-stage high-pressure turbine (HPT) air
seal, part number (P/N) 54L041, 50L960, or 50L976, installed.
(d) Unsafe Condition
This AD was prompted by additional reports of cracking in the
second-stage HPT air seal. We are issuing this AD to prevent failure
of the second-stage HPT air seal, which could lead to uncontained
engine failure and damage to the airplane.
(e) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(1) At the next piece-part exposure after the effective date of
this AD, do the following:
(i) Remove from service second-stage HPT air seals, P/N 50L960,
50L976, and 50L041.
(ii) Fluorescent-penetrant inspect (FPI) second-stage HPT air
seal, P/N 50L041, for a through-crack in the front forward fillet
radius.
(iii) If a through-crack in the front forward fillet radius is
found, remove the first-stage HPT hub, second-stage HPT hub, and
second-stage HPT blade retaining plate from service. Do not
reinstall the first-stage HPT hub, second-stage HPT hub, or second-
stage HPT blade retaining plate into any engine.
(2) For engines with second-stage HPT air seals, P/N 50L041,
installed, perform initial and repetitive inspections for cracks on-
wing until the part is removed from the engine as follows:
(i) Perform an initial eddy current inspection (ECI) for cracks
prior to reaching 2,200 cycles-since-new or within 100 cycles-in-
service after the effective date of this AD, whichever occurs later.
(ii) Thereafter, repeat the ECI every 1,200 cycles since last
inspection, or fewer, depending on the results of the inspection.
(iii) Use section 4.0 of the appendix of PW Alert Service
Bulletin (ASB) No. PW4G-112-A72-330, Revision 2, dated July 11,
2013, to perform the inspection and use paragraph 8 of the
Accomplishment Instructions of PW ASB No. PW4G-112-A72-330, Revision
2, dated July 11, 2013, to disposition the results of the
inspection.
(f) Installation Prohibition
After the effective date of this AD, do not install any second-
stage HPT air seal P/N 50L041, P/N 50L960, or P/N 50L976 into any
engine.
(g) Definitions
(1) For the purpose of this AD, piece-part exposure is when the
second-stage HPT air seal is removed from the engine and fully
disassembled.
(2) For the purpose of this AD, a through-crack is a crack that
has propagated through the thickness of the part and can be seen on
both the inner diameter and outer diameter of the front forward
fillet radius.
(h) Credit for Previous Actions
(1) If you performed an ECI of the second-stage HPT air seal
before the effective date of this AD, using PW ASB No. PW4G-112-A72-
330, Revision 1, dated February 14, 2013, or earlier version, you
have met the requirements of paragraph (e)(2)(i) of this AD.
(2) If you performed an in-shop FPI of the second-stage HPT air
seal before the effective date of this AD, you have met the
requirements of paragraph (e)(2)(i) of this AD.
(i) Alternative Methods of Compliance (AMOCs)
The Manager, Engine Certification Office, FAA, may approve AMOCs
for this AD. Use the procedures found in 14 CFR 39.19 to make your
request.
(j) Related Information
(1) For more information about this AD, contact James Gray,
Aerospace Engineer, Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington, MA
01803; phone: (781) 238-7742; fax: (781) 238-7199; email:
[email protected].
(2) For service information identified in this AD, contact Pratt
& Whitney Division, 400 Main St., East Hartford, CT 06108; phone:
(860) 565-8770; fax: (860) 565-4503.
(3) You may view this service information at the FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington,
MA. For information on the availability of this material at the FAA,
call (781) 238-7125.
Issued in Burlington, Massachusetts, on May 28, 2014.
Colleen M. D'Alessandro,
Assistant Directorate Manager, Engine & Propeller Directorate, Aircraft
Certification Service.
[FR Doc. 2014-12973 Filed 6-3-14; 8:45 am]
BILLING CODE 4910-13-P