[Federal Register Volume 79, Number 149 (Monday, August 4, 2014)]
[Proposed Rules]
[Pages 45135-45137]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-18367]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
Federal Register / Vol. 79, No. 149 / Monday, August 4, 2014 /
Proposed Rules
[[Page 45135]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2014-0489; Directorate Identifier 2014-NM-048-AD]
RIN 2120-AA64
Airworthiness Directives; Bombardier, Inc. Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for
certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 &
440) airplanes. This proposed AD was prompted by a report indicating
that inboard and outboard hydraulic lines of the brakes were found
connected to the incorrect ports on the swivel assembly of the main
landing gear (MLG). This proposed AD would require modifying the MLG by
installing a new bracket on the left and right lower aft-wing planks.
We are proposing this AD to prevent incorrect installation of the brake
hydraulic lines, which could cause the brakes and the anti-skid system
to operate incorrectly, and cause catastrophic failure of the airplane
during a high-speed rejected takeoff.
DATES: We must receive comments on this proposed AD by September 18,
2014.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email
[email protected]; Internet http://www.bombardier.com. You
may view this referenced service information at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information
on the availability of this material at the FAA, call 425-227-1221.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0489; or in person at the Docket Management Facility between 9 a.m. and
5 p.m., Monday through Friday, except Federal holidays. The AD docket
contains this proposed AD, the regulatory evaluation, any comments
received, and other information. The street address for the Docket
Operations office (telephone 800-647-5527) is in the ADDRESSES section.
Comments will be available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer,
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY
11590; telephone (516) 228-7303; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0489;
Directorate Identifier 2014-NM-048-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD based on those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
Transport Canada Civil Aviation (TCCA), which is the aviation
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-10, dated February 12, 2014 (referred to after this as the
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to
correct an unsafe condition for certain Bombardier, Inc. Model CL-600-
2B19 (Regional Jet Series 100 & 440) airplanes. The MCAI states:
Cases of inboard and outboard hydraulic brake lines connected to
the incorrect port of the swivel assembly on the main landing gear
were found in service, including a runway overrun event. Cross-
connected brake hydraulic lines can cause the brakes and/or the
anti-skid system to operate incorrectly. During a high speed
rejected take-off, inability for the brakes to operate correctly
could be catastrophic.
This [Canadian] AD mandates the modification to prevent
inadvertent cross-connection of the inboard and outboard hydraulic
brake lines.
The required action in this AD includes installing a new bracket on
the left and right lower aft-wing planks of the MLG. You may examine
the MCAI in the AD docket on the Internet at http://www.regulations.gov
by searching for and locating Docket No. FAA-2014-0489.
Relevant Service Information
Bombardier, Inc. has issued Service Bulletin 601R-32-110, dated
December 19, 2013. The actions described in this service information
are intended to correct the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI and service
information
[[Page 45136]]
referenced above. We are proposing this AD because we evaluated all
pertinent information and determined an unsafe condition exists and is
likely to exist or develop on other products of the same type design.
``Contacting the Manufacturer'' Paragraph in This Proposed AD
Since late 2006, we have included a standard paragraph titled
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD
based on a foreign authority's AD.
The MCAI or referenced service information in an FAA AD often
directs the owner/operator to contact the manufacturer for corrective
actions, such as a repair. Briefly, the Airworthy Product paragraph
allowed owners/operators to use corrective actions provided by the
manufacturer if those actions were FAA-approved. In addition, the
paragraph stated that any actions approved by the State of Design
Authority (or its delegated agent) are considered to be FAA-approved.
In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR
78285, December 26, 2013), we proposed to prevent the use of repairs
that were not specifically developed to correct the unsafe condition,
by requiring that the repair approval provided by the State of Design
Authority or its delegated agent specifically refer to the FAA AD. This
change was intended to clarify the method of compliance and to provide
operators with better visibility of repairs that are specifically
developed and approved to correct the unsafe condition. In addition, we
proposed to change the phrase ``its delegated agent'' to include a
design approval holder (DAH) with State of Design Authority design
organization approval (DOA), as applicable, to refer to a DAH
authorized to approve required repairs for the proposed AD.
One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The
proposed wording, being specific to repairs, eliminates the
interpretation that Airbus messages are acceptable for approving minor
deviations (corrective actions) needed during accomplishment of an AD
mandated Airbus service bulletin.''
This comment has made the FAA aware that some operators have
misunderstood or misinterpreted the Airworthy Product paragraph to
allow the owner/operator to use messages provided by the manufacturer
as approval of deviations during the accomplishment of an AD-mandated
action. The Airworthy Product paragraph does not approve messages or
other information provided by the manufacturer for deviations to the
requirements of the AD-mandated actions. The Airworthy Product
paragraph only addresses the requirement to contact the manufacturer
for corrective actions for the identified unsafe condition and does not
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request
the approval for an alternative method of compliance to the AD-required
actions using the procedures found in 14 CFR 39.19.
To address this misunderstanding and misinterpretation of the
Airworthy Product paragraph, we have changed the paragraph and retitled
it ``Contacting the Manufacturer.'' This paragraph now clarifies that
for any requirement in this proposed AD to obtain corrective actions
from a manufacturer, the action must be accomplished using a method
approved by the FAA, TCCA, or Bombardier's TCCA Design Approval
Organization (DAO).
The Contacting the Manufacturer paragraph also clarifies that, if
approved by the DAO, the approval must include the DAO-authorized
signature. The DAO signature indicates that the data and information
contained in the document are TCCA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer
that do not contain the DAO-authorized signature approval are not TCCA-
approved, unless TCCA directly approves the manufacturer's message or
other information.
This clarification does not remove flexibility previously afforded
by the Airworthy Product paragraph. Consistent with long-standing FAA
policy, such flexibility was never intended for required actions. This
is also consistent with the recommendation of the Airworthiness
Directive Implementation Aviation Rulemaking Committee to increase
flexibility in complying with ADs by identifying those actions in
manufacturers' service instructions that are ``Required for
Compliance'' with ADs. We continue to work with manufacturers to
implement this recommendation. But once we determine that an action is
required, any deviation from the requirement must be approved as an
alternative method of compliance.
Costs of Compliance
We estimate that this proposed AD affects 526 airplanes of U.S.
registry.
We also estimate that it would take about 6 work-hours per product
to comply with the basic requirements of this proposed AD. The average
labor rate is $85 per work-hour. Required parts would cost about $375
per product. Based on these figures, we estimate the cost of this
proposed AD on U.S. operators to be $465,510, or $885 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This proposed regulation is
within the scope of that authority because it addresses an unsafe
condition that is likely to exist or develop on products identified in
this rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska; and
4. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator,
[[Page 45137]]
the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
Bombardier, Inc.: Docket No. FAA-2014-0489; Directorate Identifier
2014-NM-048-AD.
(a) Comments Due Date
We must receive comments by September 18, 2014.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional
Jet Series 100 & 440) airplanes, certificated in any category,
serial numbers 7003 and subsequent.
(d) Subject
Air Transport Association (ATA) of America Code 32, Landing
Gear.
(e) Reason
This AD was prompted by a by a report indicating that inboard
and outboard hydraulic lines of the brakes were found connected to
the incorrect ports on the swivel assembly of the main landing gear
(MLG). We are issuing this AD to prevent incorrect installation of
the brake hydraulic lines, which could cause the brakes and the
anti-skid system to operate incorrectly, and cause catastrophic
failure of the airplane during a high-speed rejected take-off.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Modification
Within 6,600 flight hours after the effective date of this AD,
but no later than 36 months after the effective date of this AD:
Modify the MLG by installing a new bracket on the left and right
lower aft-wing planks, in accordance with the Accomplishment
Instruction of Bombardier Service Bulletin 601R-32-110, dated
December 19, 2013.
(h) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York Aircraft Certification Office (ACO), ANE-170, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the New York ACO, send it to ATTN: Program Manager,
Continuing Operational Safety, FAA, New York ACO, 1600 Stewart
Avenue, Suite 410, Westbury, NY 11590; telephone 516 228-7300; fax
516-794-5531. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must
specifically reference this AD.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain corrective actions from a manufacturer, the action must be
accomplished using a method approved by the Manager, New York ACO,
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval
Organization (DAO). If approved by the DAO, the approval must
include the DAO-authorized signature.
(i) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information
(MCAI) Canadian Airworthiness Directive CF-2014-10, dated February
12, 2014, for related information. This MCAI may be found in the AD
docket on the Internet at http://www.regulations.gov by searching
for and locating Docket No. FAA-2014-0489.
(2) For service information identified in this AD, contact
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval,
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email [email protected]; Internet http://www.bombardier.com. You may view this service information at the
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton,
WA. For information on the availability of this material at the FAA,
call 425-227-1221.
Issued in Renton, Washington, on July 18, 2014.
John P. Piccola,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2014-18367 Filed 8-1-14; 8:45 am]
BILLING CODE 4910-13-P