[Federal Register Volume 79, Number 230 (Monday, December 1, 2014)]
[Proposed Rules]
[Pages 71031-71033]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2014-28188]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2013-0766; Directorate Identifier 2013-NE-26-AD]
RIN 2120-AA64
Airworthiness Directives; Pratt & Whitney Canada Corp. Turboprop
Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to revise airworthiness directive (AD) 2014-17-08
that applies to all Pratt & Whitney Canada Corp. (P&WC) PT6A-114 and
PT6A-114A turboprop engines. AD 2014-17-08 requires initial and
repetitive borescope inspections (BSIs) of compressor turbine (CT)
blades, and the removal from service of blades that fail inspection.
Since we issued AD 2014-17-08, P&WC developed an additional single
crystal CT blade that corrects the unsafe condition. This proposed AD
would retain all the requirements of AD 2014-17-08, add an additional
single crystal CT blade that corrects the unsafe condition, reduce the
affected population, and correct the Credit for Previous Action
paragraph.
[[Page 71032]]
We are proposing this AD to prevent failure of CT blades, which could
result in damage to the engine and damage to the airplane.
DATES: We must receive comments on this proposed AD by January 30,
2015.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE., Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Pratt & Whitney Canada Corp., 1000 Marie-Victorin, Longueuil, Quebec,
Canada, J4G 1A1; phone: 800-268-8000; fax: 450-647-2888; Internet:
www.pwc.ca. You may view this service information at the FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington, MA.
For information on the availability of this material at the FAA, call
781-238-7125.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2013-
0766; or in person at the Docket Management Facility between 9 a.m. and
5 p.m., Monday through Friday, except Federal holidays. The AD docket
contains this proposed AD, the mandatory continuing airworthiness
information, regulatory evaluation, any comments received, and other
information. The address for the Docket Office (phone: 800-647-5527) is
in the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Robert Morlath, Aerospace Engineer,
Engine Certification Office, FAA, Engine & Propeller Directorate, 12
New England Executive Park, Burlington, MA 01803; phone: 781-238-7154;
fax: 781-238-7199; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this NPRM. Send your comments to an address listed
under the ADDRESSES section. Include ``Docket No. FAA-2013-0766;
Directorate Identifier 2013-NE-26-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this NPRM. We will
consider all comments received by the closing date and may amend this
NPRM because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this NPRM.
Discussion
On August 18, 2014, we issued AD 2014-17-08, Amendment 39-17961 (79
FR 52172, September 3, 2014), (``AD 2014-17-08''), for all P&WC PT6A-
114 and PT6A-114A turboprop engines. AD 2014-17-08 requires initial and
repetitive BSIs of CT blades, and the removal from service of blades
that fail inspection. AD 2014-17-08 resulted from several incidents of
CT blade failure, causing power loss, and engine failure. We issued AD
2014-17-08 to prevent failure of CT blades, which could result in
damage to the engine and damage to the airplane.
Actions Since AD 2014-17-08 Was Issued
Since we issued AD 2014-17-08 (79 FR 52172, September 3, 2014),
P&WC developed a new single crystal CT blade, P/N 3079351-01, to
correct the unsafe condition. The addition of this new P/N reduces the
affected population. Finally, we determined that in AD 2014-07-08, we
gave credit for action that is inapplicable to the unsafe condition.
Specifically, in the Credit for Previous Action paragraph, the AD
allows credit for a previously performed metallurgical examination of
``single crystal CT blades''. Metallurgical examination of single
crystal CT blades is inapplicable to the non-single crystal CT blades
referenced in Compliance paragraph (e)(1)(iii)(B) of this NPRM.
Relevant Service Information
We reviewed P&WC Service Bulletin (SB) No. PT6A-72-1669, Revision
9, dated June 28, 2013. The service information describes procedures
for correcting the unsafe condition.
FAA's Determination
We are proposing this NPRM because we evaluated all the relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the same type design.
Proposed AD Requirements
This NPRM would require initial and repetitive BSIs of CT blades,
and the removal from service of blades that fail inspection. This NPRM
would also require as a mandatory terminating action, replacement of
non-single crystal CT blades with single crystal CT blades at the next
shop visit. This NPRM also corrects the reference to single crystal CT
blades in the Credit for Previous Action paragraph. This NPRM also
reduces the affected population by introducing a new single crystal CT
blade P/N that addresses the unsafe condition.
Costs of Compliance
We estimate that this proposed AD affects 300 engines installed on
airplanes of U.S. registry. We also estimate that it would take about 4
hours per engine to perform the required inspection and 8 hours to
replace the blades. The average labor rate is $85 per hour. Required
parts cost about $59,334 per engine. Based on these figures, we
estimate the cost of this proposed AD on U.S. operators to be
$18,106,200.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and
[[Page 71033]]
responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska to the extent
that it justifies making a regulatory distinction, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. Amend Sec. 39.13 by removing airworthiness directive (AD) 2014-17-
08, Amendment 39-17961 (79 FR 52172, September 3, 2014), and adding the
following new AD:
Pratt & Whitney Canada Corp.: Docket No. FAA-2013-0766; Directorate
Identifier 2013-NE-26-AD.
(a) Comments Due Date
We must receive comments by January 30, 2015.
(b) Affected ADs
This AD replaces AD 2014-17-08, Amendment 39-17961 (79 FR 52172,
September 3, 2014).
(c) Applicability
This AD applies to all Pratt & Whitney Canada Corp. (P&WC) PT6A-
114 and PT6A-114A turboprop engines.
(d) Unsafe Condition
This AD was prompted by several incidents of compressor turbine
(CT) blade failure, causing power loss, and engine failure. We are
issuing this AD to prevent failure of CT blades, which could lead to
damage to the engine and damage to the airplane.
(e) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(1) For engines installed with CT blades other than P&WC single
crystal CT blades, part numbers (P/Ns) 3072791-01, 3072791-02, or
3079351-01, do the following:
(i) Until removed, per the requirements of this AD, borescope
inspect the CT blade leading and trailing edges, within the
following intervals, whichever occurs later:
(A) 150 operating hours after October 8, 2014; or
(B) 500 operating hours since new; or
(C) 500 operating hours since last borescope inspection (BSI) of
the CT blades; or
(D) Before next flight after the effective date of this AD.
(ii) Thereafter, repeat the inspection required by paragraph
(e)(1)(i) of this AD every 500 flight hours time since last
inspection.
(iii) At the next hot section inspection (HSI) after the
effective date of this AD, and each HSI thereafter, replace the
complete set of CT blades with any of the following:
(A) New CT blades;
(B) CT blades that have passed a two-blade metallurgical
inspection. Use paragraph 3.B., Accomplishment Instructions, of P&WC
Service Bulletin (SB) No. PT6A-72-1669, Revision 9, dated June 28,
2013, to do the inspection; or
(C) P&WC single crystal CT blades, P/Ns 3072791-01, 3072791-02,
or 3079351-01.
(2) Replacement of the complete set of CT blades with single
crystal CT blades, P/Ns 3072791-01, 3072791-02, or 3079351-01 is
terminating action for the requirements of paragraph (e)(1) of this
AD.
(3) By October 8, 2017, replace the complete set of CT blades
with P&WC single crystal CT blades, P/Ns 3072791-01, 3072791-02, or
3079351-01.
(g) Credit for Previous Action
Performance of the metallurgical examination specified in
paragraph (e)(1)(iii)(B) of this AD on CT blades other than P&WC
single crystal CT blades, P/Ns 3072791-01, 3072791-02, or 3079351-
01, before the effective date of this AD fulfils the initial
inspection requirements of paragraph (e)(1)(i) of this AD. However,
you must still comply with the repetitive BSI requirement of
paragraph (e)(1)(ii) of this AD until you complete the mandatory
terminating action of paragraph (e)(3) of this AD.
(h) Alternative Methods of Compliance (AMOCs)
(1) AMOCs previously approved for AD 2014-17-08, Amendment 39-
17961 (79 FR 52172, September 3, 2014) are approved for this AD.
(2) The Manager, Engine Certification Office, FAA, may approve
AMOCs for this AD. Use the procedures found in 14 CFR 39.19 to make
your request. You may email your request to: [email protected].
(i) Related Information
(1) For more information about this AD, contact Robert Morlath,
Aerospace Engineer, Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington, MA
01803; phone: 781-238-7154; fax: 781-238-7199; email:
[email protected].
(2) Refer to MCAI Transport Canada Civil Aviation AD CF-2013-
21R1, dated November 13, 2013, for more information. You may examine
the MCAI in the AD docket on the Internet at http://www.regulations.gov/#!documentDetail;D=FAA-2013-0766-0008.
(3) P&WC SB No. PT6A-72-1669, Revision 9, dated June 28, 2013,
which is not incorporated by reference in this AD, can be obtained
from P&WC, using the contact information in paragraph (i)(4) of this
AD.
(4) For service information identified in this AD, contact Pratt
& Whitney Canada Corp., 1000 Marie-Victorin, Longueuil, Quebec,
Canada, J4G 1A1; phone: 800-268-8000; fax: 450-647-2888; Internet:
www.pwc.ca.
(5) Guidance for performing the BSI of the CT blades leading and
trailing edges can be found in paragraph 3.A, Accomplishment
Instructions, P&WC SB No. PT6A-72-1669, Revision 9, dated June 28,
2013.
(6) You may view this service information at the FAA, Engine &
Propeller Directorate, 12 New England Executive Park, Burlington,
MA. For information on the availability of this material at the FAA,
call 781-238-7125.
Issued in Burlington, Massachusetts, on November 20, 2014.
Colleen M. D'Alessandro,
Assistant Directorate Manager, Engine & Propeller Directorate, Aircraft
Certification Service.
[FR Doc. 2014-28188 Filed 11-28-14; 8:45 am]
BILLING CODE 4910-13-P