[Federal Register Volume 81, Number 13 (Thursday, January 21, 2016)]
[Rules and Regulations]
[Pages 3636-3686]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-00780]
[[Page 3635]]
Vol. 81
Thursday,
No. 13
January 21, 2016
Part III
Department of Transportation
-----------------------------------------------------------------------
Pipeline and Hazardous Materials Safety Administration
-----------------------------------------------------------------------
49 CFR Parts 107, 171, 172, et al.,
Hazardous Materials: Adoption of Special Permits (MAP-21) (RRR); Final
Rule
Federal Register / Vol. 81 , No. 13 / Thursday, January 21, 2016 /
Rules and Regulations
[[Page 3636]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Pipeline and Hazardous Materials Safety Administration
49 CFR Parts 107, 171, 172, 173, 174, 176, 177, 178, and 180
[Docket No. PHMSA-2013-0042 (HM-233F)]
RIN 2137-AF00
Hazardous Materials: Adoption of Special Permits (MAP-21) (RRR)
AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA),
DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: As required by the Moving Ahead for Progress in the 21st
Century Act
(MAP-21), the Pipeline and Hazardous Materials Safety
Administration is amending the Hazardous Materials Regulations to adopt
provisions contained in certain widely-used or long-standing special
permits that have an established safety record. The adopted amendments
are intended to provide wider access to the regulatory flexibility
offered in special permits and eliminate the need for numerous renewal
requests. The adopted amendments will also reduce paperwork burdens and
facilitate commerce while maintaining an appropriate level of safety.
PHMSA conducted an extensive analysis of all active special permits and
codified, as appropriate, those special permits deemed suitable in this
rulemaking.
DATES: Effective Date: The final rule will become effective on February
22, 2016.
Voluntary compliance date: PHMSA is authorizing voluntary
compliance beginning February 22, 2016.
Delayed compliance date: Unless otherwise specified, compliance
with the amendments adopted in this final rule is required beginning
January 23, 2017.
FOR FURTHER INFORMATION CONTACT: Donald Burger, Office of Hazardous
Materials Safety, Approvals and Permits Division, (202) 366-4535, or T.
Glenn Foster, Office of Hazardous Materials Safety, Standards and
Rulemaking Division, (202) 366-8553, Pipeline and Hazardous Materials
Safety Administration, U.S. Department of Transportation, 1200 New
Jersey Ave. SE., Washington, DC 20590-0001.
SUPPLEMENTARY INFORMATION:
Table of Contents
I. Executive Summary
II. Background
III. Overview
A. MAP-21 Legislation
B. SP Conversion Project Methodology
C. Petitions for Rulemaking
D. SP Evaluation Results
E. SPs Suitable for Adoption
IV. Public Comments
A. General/Administrative
B. Cylinders--General
C. Cylinders--Non-Destructive Testing/Aerosols
D. Cargo Tanks/Rail Cars/Portable Tanks
E. Operational Air/Vessel
F. Operational Highway/Rail/Shipper/Other
G. Non-Bulk Packaging Specifications/IBCs
V. Section-by-Section Review by Topic Area
A. Cylinders--General
B. Cylinders--Non-Destructive Testing/Aerosols
C. Cargo Tanks/Rail Cars/Portable Tanks
D. Operational Air/Vessel
E. Operational Highway/Rail/Shipper/Other
F. Non-Bulk Packaging Specifications/IBCs
VI. Regulatory Analyses and Notices
A. Statutory/Legal Authority for This Rulemaking
B. Executive Order 12866, Executive Order 13563, Executive Order
13610, and DOT Regulatory Policies and Procedures
C. Executive Order 13132
D. Executive Order 13175
E. Regulatory Flexibility Act, Executive Order 13272, and DOT
Procedures and Policies
F. Paperwork Reduction Act
G. Regulatory Identifier Number (RIN)
H. Unfunded Mandates Reform Act
I. Executive Order 13609 and International Trade Analysis
J. Environmental Assessment and NEPA Analysis
K. Privacy Act
L. National Technology Transfer and Advancement Act
List of Subjects
I. Executive Summary
The Pipeline and Hazardous Materials Safety Administration (PHMSA)
is amending the Hazardous Materials Regulations (HMR; 49 CFR parts 171-
180) by adopting requirements contained in 96 existing special permits
(SP). These amendments are based on our review of all active SPs as of
January 1, 2013, in which we originally identified 98 SPs containing
requirements that appear suitable for adoption into the HMR as
regulations of general applicability. Other SPs (1,070) were not
proposed for adoption into the HMR because we concluded they contain
requirements which (1) would not have, or are being applied in a manner
which would not have, broad applicability; or (2) have already been
adopted into the HMR, are covered by authorizations in the HMR, are
being addressed in other rulemakings, or were removed from
consideration after receiving public comments submitted in response to
the January 30, 2015, notice of proposed rulemaking (NPRM) in this
proceeding.
In the NPRM published in the Federal Register on January 30, 2015
[80 FR 5339], we encouraged all interested parties, particularly the
holders of currently active SPs, to submit comments regarding the SPs
we proposed to adopt into the HMR, the SPs we did not propose to adopt
into the HMR, and the impacts, including costs and benefits, of the
special permits proposed for incorporation.
II. Background
PHMSA is amending the Hazardous Materials Regulations (HMR; 49 CFR
Parts 171-180) by adopting certain requirements based on existing SPs
issued by PHMSA under 49 CFR part 107, subpart B (Sec. Sec. 107.101 to
107.127). SPs set forth alternative requirements--or a variance--to the
requirements in the HMR in a way that achieves a safety level at least
equal to the safety level required under the regulations, or, when the
regulations do not establish a safety level, that is consistent with
the public interest. Congress expressly authorized the Secretary of
Transportation to issue these variances in the Hazardous Materials
Transportation Act of 1975 (49 U.S.C. 5109) as amended.
On July 6, 2013, President Obama signed legislation entitled
``Moving Ahead for Progress in the 21st Century Act (MAP-21).'' Section
33012 of this legislation required PHMSA to review and analyze SPs that
have been in continuous effect for a 10-year period to determine which
ones may be codified into the HMR.\1\ The legislation also required
PHMSA to issue regulations to adopt any SPs identified as appropriate
for adoption in a final rule by October 1, 2015. The legislation
provided the following factors to consider during review and analysis
to determine suitability for adoption into the HMR:
---------------------------------------------------------------------------
\1\ Although MAP-21 only required PHMSA evaluate SPs that had
been in continuous effect for a 10-year period, PHMSA reviewed all
active SPs as of January 1, 2013.
---------------------------------------------------------------------------
(1) The safety record of the hazardous materials (hazmat)
transported under the SP;
(2) The application of a SP;
(3) The suitability of the provisions in the SP for incorporation
into the hazmat regulations; and
(4) Rulemaking activity in related areas.
Prior to the passing of the MAP-21 legislation, PHMSA completed
numerous rulemaking actions, through a comprehensive and refined
approach, to convert long-standing SPs with an established safety
record into the HMR.
[[Page 3637]]
Following the passage of the MAP-21 legislation, PHMSA modified its
approach to align with the requirements of this legislation.
Specifically, PHMSA established terms of reference and baseline
criteria for the review of long-standing SPs, created tracking tools to
monitor progress, and adopted a methodology and timeline to evaluate
SPs.
The January 30, 2015 NPRM provided an overview of the SP Program to
date, a detailed review of the requirements of MAP-21 with regard to
this initiative, and a comprehensive explanation of the rationale used
to evaluate these SPs both prior to and after the implementation of
MAP-21. Furthermore, the NPRM described in detail the SPs that were
deemed not suitable for adoption into the HMR along with the
corresponding reasoning, and proposed the adoption into the HMR of SPs
that were deemed suitable through this review. The amendments adopted
from the SPs in this final rule have broad applicability, fit into the
scope of the HMR, increase flexibility in transportation, and provide
an equivalent level of safety to that of the current regulations.
III. Overview
Historically, PHMSA has reviewed widely used or long-standing
special permits and adopted those that have an established safety
record into the HMR. Since 2008, PHMSA has adopted 94 special permits
under various rulemakings into the HMR, reducing the number of holders
by 13,947. Rulemakings that stemmed from a special permit are noted in
Table 1.
---------------------------------------------------------------------------
\2\ This table represents only published rulemakings since
January 1, 2008.
Table 1--Previous Rulemaking Actions \2\
----------------------------------------------------------------------------------------------------------------
Number of
Docket No. Title Purpose permits Holders
----------------------------------------------------------------------------------------------------------------
PHMSA-2006-25910 (HM-218E)....... Miscellaneous Cargo Amended the HMR to 2 15
Tank Motor Vehicle revise certain
and Cylinder requirements applicable
Issues; Petitions to the manufacture,
for Rulemaking. maintenance, and use of
DOT and MC
specification cargo
tank motor vehicles,
DOT specification
cylinders and UN
pressure receptacles.
PHMSA-2008-0005 (HM-215J)........ Revision to Amended the HMR to 3 6
Requirements for maintain alignment with
the Transportation international standards
of Batteries and by adopting various
Battery-Powered amendments, including
Devices; and changes to proper
Harmonization with shipping names, hazard
the UN classes, packing
Recommendations, groups, special
IMDG Code, and provisions, packaging
ICAO Technical authorizations, air
Instructions. transport quantity
limitations, and vessel
stowage requirements.
PHMSA-2009-0151 (HM-218F)........ Miscellaneous Amended the HMR to make 1 1
Amendments. miscellaneous revisions
to update and clarify
certain regulatory
requirements.
PHMSA-2009-0289 (HM-233A)........ Incorporation of Amended the HMR to adopt 44 510
SPs into provisions contained in
Regulations. certain widely-used or
long-standing SPs that
have an established
safety record.
PHMSA-2010-0017 (HM-245)......... Incorporation of Amended the HMR to adopt 6 Over 10,000
Cargo Tank SPs. provisions contained in
certain widely-used or
long-standing cargo
tank SPs that are
granted to multiple
parties and have
established safety
records.
PHMSA-2010-0018 (HM-216B)........ Incorporating Rail Amended the HMR to adopt 7 250
SPs. SPs which authorized an
alternative tank car
qualification program,
acceptance of shipping
paper information by
voice or electronic
data interchange,
provide alternative
rail car segregation
requirements for
explosives, alternative
tank car design
requirements, and
alternative unloading
provisions for coupled
tank cars.
PHMSA-2010-0201 HM-254........... Approval and Amended the HMR 2 2,131
Communication applicable to airbag
Requirements for inflators, airbag
the Safe modules and seat-belt
Transportation of pretensioners by
Airbag Inflators, authorizing an
Airbag Modules, alternative review and
and Seat-belt verification process
Pretensioners. for these devices, and
eliminating the current
requirements to have
hundreds of these
devices approved by
PHMSA prior to shipment.
PHMSA 2011-0138 (HM 218G)........ Miscellaneous Amended the HMR by 1 1
Amendments (RRR). adopting SPs to
authorize the
transportation by motor
vehicle of certain
regulated medical
wastes, designated as
sharps, in non-DOT
specification
containers fitted into
wheeled racks.
[[Page 3638]]
PHMSA-2011-0142 (HM-219)......... Miscellaneous Amended the HMR to no 1 1
Petitions for longer require re-
Rulemaking (RRR). application for a SP to
place the Dangerous
Cargo Manifest in
locations designated by
the master of the
vessel besides ``on or
near the bridge'' while
the vessel is docked in
a United States port
while cargo unloading,
loading, or handling
operations are underway
and the bridge is
unmanned.
PHMSA-2011-0158 (HM-233C)........ Incorporation of Amended the HMR to adopt 18 466
Certain SPs and provisions contained in
Competent several SPs that
Authorities into provide greater
Regulations. regulatory flexibility.
The SPs in this action
addressed a variety of
alternative provisions,
including alternative
packaging
authorizations for
specific hazardous
materials (HM), and
would eliminate
approval requirements
for variances in the
manufacture of
fiberboard packagings.
PHMSA-2011-0345 (HM-233D) (NPRM). Requirements for Proposes to amend the 9 566
the Safe HMR by establishing
Transportation of standards for the safe
Bulk Explosives transportation of bulk
(RRR). explosives. This
rulemaking would also
be responsive to two
petitions (P-1557, P-
1583).
-------------------------------
Total........................ ................... ........................ 94 13,947
----------------------------------------------------------------------------------------------------------------
A. MAP-21 Legislation
Section 33012 of the MAP-21 legislation revised section 5117 (f) of
the Federal Hazardous Materials Transportation Law. As a result of this
legislation, PHMSA was required to review and analyze SPs that have
been in effect for 10 years or more and determine which could be
converted into regulations. Additionally, PHMSA was required to set
parameters for the review and issue regulations to adopt any SPs
identified as appropriate for adoption in a final rule by October 1,
2015. Following publication of this final rule, this process would be
completed annually to ensure appropriate SPs are converted into the HMR
on a consistent basis.
The legislation also required PHMSA to address other issues related
to the SP and approvals regulations and program processes.
Specifically, PHMSA is required to issue regulations on standard
operating procedures to support administration of the SP and approval
programs. This requirement is being addressed under Docket No. PHMSA
2012-0260 (HM-233E).
Table 2 summarizes the MAP-21 requirements related to the SP
program, the corresponding rulemaking actions, and required completion
dates:
Table 2--MAP-21 Summary
----------------------------------------------------------------------------------------------------------------
MAP-21 citation MAP-21 requirement Docket No. Required completion date
----------------------------------------------------------------------------------------------------------------
Sec. 33012
(a)...................... Rulemaking mandate. PHMSA PHMSA 2012-0260 (HM- Final rule due by 10/01/
shall issue regulations that 233E). 2014.
establish:
(1) Standard operating
procedures to support
administration of the SP and
approval programs; and
(2) Objective criteria to
support the evaluation of
SP and approval
applications.
(b)...................... Initial review and analysis PHMSA-2013-0042 (HM- Review and analysis due
of SPs that have been in 233F). by 10/01/2013.
continuous effect for a 10-
year period to determine
which ones may be converted
into the hazmat regulations.
Factors to consider:
(1) The safety record of
hazmat transported under the
SP;
(2) The application of a SP;
(3) The suitability of
provisions in the SP for
incorporation into the
hazmat regulations; and
(4) Rulemaking activity in
related areas.
(b)...................... Rulemaking mandate. Issue PHMSA-2013-0042 (HM- Final rule due by 10/01/
regulations to incorporate 233F). 2015.
into the hazmat regulations
any SPs identified in the
initial review and analysis
that PHMSA determines are
appropriate for
incorporation based on the
review factors.
(c)...................... Ongoing review and analysis Continuous future Review and analysis due
of SPs. Not later than 1 rulemaking actions on a by 10/01/2015 and to be
year after the date on which yearly basis. completed on an annual
a SP has been in continuous basis.
effect for a 10-year period,
PHMSA shall conduct a review
and analysis of that SP to
determine whether it may be
converted into the hazmat
regulations. Factors to
consider:
(1) The safety record of
hazmat transported under the
SP;
[[Page 3639]]
(2) The application of a SP;
(3) The suitability of
provisions in the SP for
incorporation into the
hazmat regulations; and
(4) Rulemaking activity in
related areas.
(d)...................... Rulemaking mandate. After Continuous future Final rule or notice of
completing the review and rulemaking actions on a no rulemaking decision
analysis of SPs that have yearly basis. due by 10/01/2016.
been in continuous effect
for a 10-year period, PHMSA
shall either institute a
rulemaking to incorporate
the SP into the hazmat
regulations or publish in
the Federal Register its
justification for why the SP
is not appropriate for
incorporation into the
regulations.
----------------------------------------------------------------------------------------------------------------
B. SP Conversion Project Methodology
As previously stated, PHMSA has routinely analyzed, evaluated, and
adopted SPs into the HMR through established procedures for decades.
However, the specific provisions contained in MAP-21 necessitated PHMSA
to modify and formalize its approach.
The following table summarizes the different phases of the Special
Permits Conversion Project (SPCP). Specifically, this table briefly
discusses the efforts of each phase of the project and how the entire
project was divided into the two primary stages of analysis and
rulemaking. Each phase of the SPCP is described in Table 3.
Table 3--SPCP Methodology
------------------------------------------------------------------------
Phase Description of action
------------------------------------------------------------------------
Analysis:
Phase 1: Development of The SPCP Management team developed a
Methodology. methodology to consistently
evaluate SPs, a system to track
this analysis, sub-teams and sub-
topic areas used to group similar
SPs to be reviewed by the
appropriate subject matter experts,
and timelines and milestones.
Phase 2: Preliminary Analysis. An initial review of all SPs was
conducted. SPs were divided by
topics and sub-topics and each
transportation regulations
specialist was assigned a grouping.
These specialists reviewed each
permit and made a determination as
to an SP's suitability for adoption
into the HMR based on guidance
provided by the SPCP Management
team.
Phase 3: Mentor Review........ The members of the SPCP Management
were assigned topics and conducted
a second review of the SPs deemed
either not suitable or flagged for
further review.
Phase 4: Team Analysis........ PHMSA then established rulemaking
teams for each topic composed of a
team leader, mentor, and team
members from each PHMSA Division
and our modal partners. These teams
then conducted a second review of
those SPs deemed suitable and those
flagged for follow-up.
Rulemaking:
Phase 5: Drafting............. For SPs deemed suitable, the team
drafted regulatory text along with
preamble language justifying
inclusion into the HMR. The
finalized draft of each topic was
then submitted to the SPCP
Management team for final review.
Phase 6: Consolidate Following review by the SPCP
Rulemaking. Management team, the topic
rulemakings were then combined into
a master draft along with
additional preamble language,
regulatory analysis, and
information collection activities.
Phase 7: Rulemaking The master draft created was then
Coordination. vetted throughout the agency and
with our modal partners. In
addition, the rulemaking was
coordinated with the Office of the
Secretary of Transportation and the
Office of Management and Budget.
Phase 8: Rulemaking Following concurrence from all
Publication. entities, PHMSA submitted the NPRM
to the Federal Register for
publication.
Phase 9: Final Analysis and The draft Final Rule was then vetted
Coordination. throughout the agency and with our
modal partners. In addition, the
rulemaking was coordinated with the
Office of the Secretary of
Transportation and the Office of
Management and Budget.
Phase 10: Final Rulemaking Following concurrence from all
Publication. entities, PHMSA submitted this
Final Rule to the Federal Register
for publication.
------------------------------------------------------------------------
PHMSA grouped each special permit into one of six topic areas,
based on the utility of the special permit. These topic areas were
established to reflect the main utility and purpose of the SP. These
topic areas of the SPs, an overview of each topic area, and the
affected number of SP holders are detailed in Table 4.
[[Page 3640]]
Table 4--Topic Overview
------------------------------------------------------------------------
Holders
Topic Overview (total # in
grouping)
------------------------------------------------------------------------
Cylinders--General............. The SPs pertaining to 721
cylinders that are
adopted into the HMR
in this final rule
provide exceptions to
existing general
cylinder requirements.
Cylinders--NDT/Aerosols \3\.... The SPs pertaining to 396
acoustic emission (AE)
and ultrasonic
examination (UE)
testing of cylinders
and to aerosols that
are adopted into the
HMR in this final rule
provide exceptions to
existing cylinder
requirements specific
to cylinder non-
destructive testing
(NDT) and aerosols.
Cargo Tanks/Rail Cars/Portable The SPs pertaining to 321
Tanks. cargo tanks, rail
cars, and portable
tanks that are adopted
into the HMR in this
final rule provide
exceptions to existing
cargo tanks, rail
cars, and portable
tanks requirements.
Operational Air/Vessel......... The SPs pertaining to 207
operational issues for
aircraft or vessel
transportation that
are adopted into the
HMR in this final rule
provide exceptions to
existing requirements
for vessel and
aircraft shipments.
Operational Highway/Rail/ The SPs pertaining to 1,226
Shipper/Other. operational issues for
highway or rail
transport, shipper
requirements, and
other general areas
that are adopted into
the HMR in this final
rule provide
exceptions to existing
highway and rail
operations, shipper,
and other general
requirements.
Non-Bulk Packaging The SPs pertaining to 820
Specifications/IBCs. non-bulk packagings,
IBCs, and packaging
specifications that
are adopted into the
HMR in this final rule
provide certain
exceptions to the
packaging
specification
requirements.
---------------
Total...................... ....................... 3,691
------------------------------------------------------------------------
C. Petitions for Rulemaking
PHMSA considered several petitions for rulemaking submitted in
accordance with Sec. 106.105. The petitions are discussed as follows:
---------------------------------------------------------------------------
\3\ For the purposes of this rulemaking Non-Destructive Testing
(NDT) includes Ultrasonic Examination (UE) and Acoustic Emission
(AE).
---------------------------------------------------------------------------
P-1607
The Council on the Safe Transportation of Hazardous Articles
(COSTHA) submitted a petition for rulemaking under P-1607 which PHMSA
accepted and proposed in the January 30, 2015 NPRM. The purpose of this
petition for rulemaking was to adopt the provisions of SP 11458
authorizing display packs of consumer commodities that exceed the 30 kg
gross weight limitation prescribed for limited quantity packages. See
the discussions in Sec. Sec. 171.8 and 173.56 under the ``Operational
Highway/Rail/Shipper/Other'' heading of this rulemaking.
P-1608
The Truck Trailer Manufacturers Association (TTMA) submitted a
petition for rulemaking under P-1608 to adopt the provisions of SP
11903 into the HMR. Under P-1608, TTMA petitioned that PHMSA adopt
standards for the construction and use of fiber reinforced plastic
(FRP) cargo tanks. Currently, these tanks are constructed under SP
11903 and used under party status to SP 9166. Other special permits
also address these standards but PHMSA did not propose to adopt them in
the NPRM because a uniform standard for FRP cargo tanks that is ready
for adoption does not exist. However, PHMSA is working to develop a
uniform standard for FRP cargo tanks, which we will address in a future
rulemaking.
P-1610
COSTHA submitted a petition for rulemaking under P-1610 to adopt
the provisions of SP 11110 into the HMR. This SP authorizes cargo
aircraft operators to stow Division 1.4S and Class 8, PG III materials
in inaccessible cargo locations in excess of the limitations specified
in Sec. 175.75(c). This petition has been accepted by PHMSA for
consideration in a future rulemaking as more time is needed to research
the potential impact of changes to Sec. 175.75 and to coordinate this
review with the appropriate parties, including our modal partners.
P-1611
COSTHA submitted a petition for rulemaking under P-1611 to adopt
the provisions of SP 11470 into the HMR. This SP authorizes the
transportation in commerce of shrink-wrapped pallets containing
packages of waste ORM-D materials with the word ``WASTE'' marked on the
outside of the pallet instead of each individual box. This petition was
accepted by PHMSA and is being adopted as proposed in this final rule.
See the discussion in Sec. 173.12 under the ``Operational Highway/
Rail/Shipper/Other'' heading of this preamble.
D. SP Evaluation Results
PHMSA is committed to the SP adoption process established by
Congress in MAP-21. To ensure that changes made under this action are
as efficient and effective as possible, PHMSA solicited input from its
stakeholders. We used several tables throughout the NPRM to identify
SPs suitable for adoption and those that were deemed not suitable. As
required by MAP-21, the initial review and analysis of SPs considered
the following factors:
The safety record of hazardous materials transported under
the SP;
The application of a SP;
The suitability of provisions in the SP for adoption into
the HMR; and
Rulemaking activity in related areas.
Based on these factors, PHMSA developed and assigned codes
representing its reasoning for adopting or not adopting certain SPs
into the regulations. Table 5 explains each code.
Table 5--SPCP Code Key
------------------------------------------------------------------------
Code Title Explanation
------------------------------------------------------------------------
Code 1........... Suitable for Adoption SPs suitable for adoption.
[[Page 3641]]
Code 2........... Not Suitable for SPs not suitable because of
Adoption: The the manner in which applied.
application of the Because the purpose of the
SP. MAP-21 directive was to
reduce need for SPs where
widely-used, many of these
SPs were not considered
suitable for adoption because
of their application; i.e.,
they were not widely-used,
were too technical in nature,
or were too specific to a SP
holder. This Code was applied
to both single and multiple
holders of SPs.
Code 3........... Not Suitable for SPs not suitable for adoption
Adoption: The because of the lack of broad
suitability of the applicability. Similar to
provision in the SP Code 2, many of these SPs
for adoption into were not considered suitable
the HMR. for adoption because of the
specificity of the SP. The
terms of these SPs often
included an inability to
provide the same exception in
a broad manner applicable to
certain geographical
locations or safety controls.
This Code was also applied to
both single and multiple
holders of SPs.
Code 4........... Not Suitable for SPs being addressed in other
Adoption: Rulemaking rulemakings.
activity in related
areas.
Code 5........... Already adopted or SPs already adopted or
otherwise covered authorizations already
under current specified in the current HMR.
regulations. For example, these SPs will
be terminated as they are no
longer necessary since the
provisions contained within
have already been adopted or
have been covered under
current regulations.
------------------------------------------------------------------------
The SPCP evaluated 1,168 permits that represented 3,691 holders of
SPs that were active on January 1, 2013. Once the evaluation segment of
the SPCP was completed, PHMSA identified 98 active SPs that were
suitable for adoption in this proceeding. Since that time, SP-14422 has
become no longer active and its provisions are not adopted in this
final rule. Additionally, SP 4850 is not adopted in this final rule
based on concerns that certain elements in its codification no longer
communicated the exceptions from the HMR provided by the SP. Thus, we
believe any additional burden not proposed in the January 30, 2015 NPRM
would require notice and comment
Adoption of the 96 SPs in this final rule will impact 832 SP
holders as indicated in Table 6. The SPs adopted in this rulemaking
represent an approximate 8% reduction in the number of active SPs and
an approximate 23% reduction in the number of holders of those SPs as
indicated in Table 6.
Table 6--SPCP Impact
------------------------------------------------------------------------
SPs Holders
------------------------------------------------------------------------
SPs Adopted in this Rulemaking Action... 96 832
Total Number Evaluated.................. 1,168 3,691
Percent Reduction....................... 8.22% 22.54%
------------------------------------------------------------------------
When combined with previous regulatory efforts to adopt SPs into
the HMR, the impact is increased to 190 total SPs adopted since 2008,
affecting 14,779 holders of SPs as indicated in Table 7.
Table 7--SPs Adopted and Affected Holders
------------------------------------------------------------------------
SPs Holders
------------------------------------------------------------------------
SPs Eliminated in Previous Rulemaking 94 13,947
actions since 2008.....................
SPs Adopted in this Rulemaking Action... 96 832
-------------------------------
Total............................... 190 14,779
------------------------------------------------------------------------
It is PHMSA's intent to annually review all SPs that have been in
effect for more than 10 years. Further, PHMSA's ongoing review and
analysis of SPs will use the same methodology and tools as in this
proceeding. PHMSA anticipates that future analysis and review will be
more streamlined due to the reduction in the number of SPs to be
evaluated and the experience gained through this evaluation.
E. SPs Suitable for Adoption
The original analysis phase of the SPCP NPRM identified 98 SPs (728
holders) that were deemed suitable for adoption. Further, the analysis
phase identified 1,070 SPs that were deemed not suitable for adoption.
Please see the January 30, 2015 NPRM for more information on the SPs
deemed not suitable, their assigned topic area, a summary of the
permit, the number of SP holders, and each corresponding denial code.
In this final rule, Table 8 summarizes the SPs deemed suitable, their
assigned topic area, a summary of the permit, and the number of holders
of SPs. The difference in the number of holders in the NPRM (728) and
this final rule (832) are due to seven SPs proposed for adoption in the
NPRM that are not being adopted in this final rule and four SPs that
were not proposed for adoption in the NPRM that are being adopted in
this final rule. All suitable SPs (96) ultimately adopted were deemed
to be Code 1 and are adopted in this final rule.
[[Page 3642]]
Table 8--SPs Suitable for Proposed Adoption
----------------------------------------------------------------------------------------------------------------
Permit No. Category Summary Holders
----------------------------------------------------------------------------------------------------------------
Cylinders General
----------------------------------------------------------------------------------------------------------------
SP6530......................... Cylinders General......... Authorizes transportation in 26
commerce of hydrogen and mixtures
of hydrogen with helium, argon or
nitrogen, in certain cylinders
filled to 110% of their marked
service pressures.
SP8074......................... Cylinders General......... Authorizes transportation in 5
commerce of certain flammable and
non-flammable gases in DOT
specification 3E cylinders
measuring 2 inches in diameter by
12 inches long without a safety
relief device.
SP12084........................ Cylinders General......... Authorizes use of certain DOT 1
specification 4B, 4BA, or 4BW
cylinders, which are protected
externally by a suitable corrosion-
resistant coating (such as
galvanizing or painting), for
transportation in commerce of
certain gases when retested and
marked in accordance with the
requirements specified in Sec.
180.209(e). In lieu of a 5 year
periodic hydrostatic test, or
testing in accordance with Sec.
173.213(c)(2), the prescribed
cylinders may be retested and
marked in accordance with Sec.
180.209(e).
SP12301........................ Cylinders General......... Authorizes transportation in 8
commerce of chloropicrin and
methyl bromide mixtures in a DOT
specification 4BW cylinder having
a capacity greater than that
specified in Sec. 173.193(b).
SP12782........................ Cylinders General......... Authorizes transportation in 5
commerce of certain DOT
specification cylinders,
containing Divisions 2.1, 2.2 or
2.3 materials, equipped with
plastic valve protection caps.
SP13318........................ Cylinders General......... Authorizes transportation in 2
commerce of DOT specification 39
cylinders of 75 cubic inches or
less volume, except as specified,
for transportation in commerce of
certain hazardous materials.
SP13544........................ Cylinders General......... Authorizes transportation in 1
commerce of DOT specification
4BA240 cylinders containing
liquefied petroleum gas (LPG) and/
or residue of LPG without hazard
warning labels when transported in
a closed transport vehicle that is
placarded.
SP13599........................ Cylinders General......... Authorizes transportation in 1
commerce of certain Division 2.2
materials in certain DOT
specification seamless steel
cylinders.
SP14251........................ Cylinders General......... Authorizes transportation in 6
commerce of overpacked cylinders
containing Class 2 materials with
CGA C-7 neck ring labels in lieu
of the standard label.
SP14419........................ Cylinders General......... Authorizes transportation in 3
commerce of pyrophoric liquid
n.o.s. in DOT specification 3AL
cylinders that are not authorized
for that material.
SP14937........................ Cylinders General......... Authorizes transportation in 1
commerce of certain cylinders that
have requalification markings on a
label embedded in epoxy in lieu of
stamping for the transportation of
various refrigerant gases.
----------------------------------------------------------------------------------------------------------------
Cylinders--NDT/Aerosols
----------------------------------------------------------------------------------------------------------------
SP7951......................... Cylinders--NDT/Aerosols... Authorizes transportation in 5
commerce of certain aerosols
containing Division 2.2 materials,
with a charge pressure not
exceeding 150 psig at 75 [deg]F
when shipped in a refrigerated
state.
SP8786......................... Cylinders--NDT/Aerosols... Authorizes transportation in 6
commerce of limited quantities of
compressed gases, Division 2.2, in
accumulators which deviate from
the required retest parameters.
SP11296........................ Cylinders--NDT/Aerosols... Authorizes transportation in 128
commerce of certain waste aerosol
cans containing flammable gas
propellants, including isobutane
and propane, overpacked in a UN1A2
steel drum or a UN1H2 plastic drum
for disposal.
SP12573........................ Cylinders--NDT/Aerosols... Authorizes manufacture, marking, 1
sale and use of a non-refillable,
non-DOT specification inside metal
container conforming with
regulations applicable to DOT
specification 2Q, for
transportation in commerce of
certain hazardous materials.
SP12995........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of certain DOT 2Q
specification, non-refillable
containers containing polyurethane
foam or foam components that will
be tested by other means in lieu
of subjecting each container to a
hot water bath.
SP13581........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of insecticide aerosol
fogger in non-DOT specification
non-refillable inside containers.
SP13601........................ Cylinders--NDT/Aerosols... Authorizes manufacture, marking, 1
sale and use of non-DOT
specification containers for
transportation in commerce of
certain non-flammable aerosols
containing foodstuffs at pressures
exceeding those authorized.
SP14429........................ Cylinders--NDT/Aerosols... Authorizes transportation in 2
commerce of a DOT specification 2P
non-refillable aluminum in-side
container which has been leakage
tested by an automated in-line
pressure check in lieu of the hot
water bath specified in the HMR.
SP14440........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of Division 2.1 aerosols
in certain non-refillable
containers which have been tested
by an alternative method in lieu
of the hot water bath test.
SP14503........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of aerosol foodstuffs in
a non-refillable metal container
similar to DOT specification 2P
and 2Q.
[[Page 3643]]
SP14544........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of Division 2.1 and 2.2
hazardous materials in certain non-
DOT specification and DOT
specification non-refillable
aerosol containers which have been
tested by an alternative method in
lieu of the hot water bath test.
SP14623........................ Cylinders--NDT/Aerosols... Authorizes manufacture, marking, 1
sale, and use of a bag-on-valve,
non-refillable, aerosol container
which has been tested by an
alternative method in lieu of the
hot water bath test. In lieu of
the hot water bath, each container
must be subject to an automated
pressure test on the line.
SP14625........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of aerosols in certain
non-refillable containers which
have been tested by an alternative
method in lieu of the hot water
bath test. In lieu of the hot
water bath, each container will be
subject to an automated pressure
test on the line.
SP14627........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of aerosols in certain
non-refillable containers which
have been tested by an alternative
method in lieu of the hot water
bath test. In lieu of the hot
water bath, each container must be
subject to an automated pressure
test on the line.
SP14723........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of aerosols containing a
Division 2.2 compressed gas in
certain non-refillable aerosol
containers which are not subject
to the hot water bath test.
SP14724........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of an aerosol in certain
non-refillable containers which
have been tested by an alternative
method in lieu of the hot water
bath test. In lieu of the hot
water bath, each container will be
subject to an automated in-line
pressure test.
SP14786........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of DOT specification 2P
and 2Q aluminum non-refillable
inside containers which are leak
tested by an automated in-line
pressure check in lieu of the hot
water bath specified in the HMR.
SP14842........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of consumer commodity
(pressurized by nitrogen,
compressed) and aerosols, non-
flammable, (each not exceeding 1 L
capacity) in DOT specification 2P
non-refillable aluminum inside
containers which have been tested
by an alternative method in lieu
of the hot water bath test. In
lieu of the hot water bath, each
container will be subject to an
automated pressure test on the
line.
SP14887........................ Cylinders--NDT/Aerosols... Authorizes transportation of 2
aerosols and consumer commodities
in commerce of DOT specification
2P and 2Q metal non-refillable
inside containers and non-DOT
specification metal inside
containers which are leak tested
by an automated in-line pressure
check in lieu of the hot water
bath specified in the HMR.
SP14953........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of DOT specification 2Q
non-refillable aluminum inside
containers which have been leakage
tested by an 100% automated in-
line pressure check in lieu of the
hot water bath test.
SP15135........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of certain DOT 2P non-
refillable metal containers
(containing a laminate bag on
valve system) which are leak
tested by an automated in-line
pressure check in lieu of the
required hot water bath test.
SP15265........................ Cylinders--NDT/Aerosols... Authorizes manufacture, mark, sale 1
and use of non-DOT specification
bag-on-valve spray packaging
similar to an aerosol container
without requiring the hot water
bath test conforming with all
regulations applicable to a DOT
specification 2P or 2Q, except as
specified herein, for the
transportation in commerce of
certain hazardous materials.
SP15427........................ Cylinders--NDT/Aerosols... Authorizes manufacture, mark, sale 2
and use of non-refillable inside
containers which are leak tested
by an automated in-line pressure
check in lieu of the hot water
bath specified in the HMR.
SP15792........................ Cylinders--NDT/Aerosols... Authorizes transportation in 1
commerce of DOT specification 2P
non-refillable aluminum inside
containers which have been tested
by an alternative method in lieu
of the hot water bath test. In
lieu of the hot water bath, each
container will be subject to an
automated pressure test on the
line.
----------------------------------------------------------------------------------------------------------------
Cargo Tanks/Rail Cars/Portable Tanks
----------------------------------------------------------------------------------------------------------------
SP12039........................ Cargo Tanks/Rail Cars/ Authorizes transportation in 3
Portable Tanks. commerce of DOT 113C120W tank cars
containing ethylene, refrigerated
liquid, at an internal pressure of
20 psig instead of the maximum 10
psig.
SP12576........................ Cargo Tanks/Rail Cars/ Authorizes manufacture, marking, 1
Portable Tanks. sale and use of non-DOT
specification tanks conforming
with all regulations applicable to
a DOT specification MC 331 cargo
tank, except as specified, for
transportation in commerce of
certain hazardous materials.
----------------------------------------------------------------------------------------------------------------
[[Page 3644]]
Operational Air/Vessel
----------------------------------------------------------------------------------------------------------------
SP11150........................ Operational Air/Vessel.... Authorizes transportation in 1
commerce of liquefied petroleum
gas in DOT specification
cylinders, secured to transport
vehicles on passenger ferry
vessels.
SP11691........................ Operational Air/Vessel.... Authorizes transportation in 10
commerce of certain flammable and
corrosive liquids, which are the
ingredients of soft drinks
(beverages), not subject to the
segregation requirements for
vessel stowage when shipped in the
same transport unit.
SP13213........................ Operational Air/Vessel.... Authorizes stowage aboard passenger 1
ferry vessels of private motor
vehicles such as recreational
vehicles, with attached cylinders
of liquefied petroleum gas in
addition to extra containers of
gasoline (including camp stove or
lantern fuel) and portable
cylinders of liquefied petroleum
gas.
SP14458........................ Operational Air/Vessel.... Authorizes private motor vehicles 1
such as recreational vehicles,
with attached cylinders of
liquefied petroleum gas in
addition to extra containers of
gasoline (including camp stove or
lantern fuel) and portable
cylinders of liquefied petroleum
gas to be stowed aboard passenger
ferry vessels.
----------------------------------------------------------------------------------------------------------------
Operational Highway/Rail/Shipper/Other
----------------------------------------------------------------------------------------------------------------
SP7991......................... Operational Highway/Rail/ Authorizes transportation in 37
Shipper/Other. commerce of railroad flagging kits
of specified construction,
containing certain Class 1.4 and
4.1 materials, not subject to the
HMR.
SP8006......................... Operational Highway/Rail/ Authorizes certain articles, 3
Shipper/Other. explosive, n.o.s., Division 1.4S
(toy caps) to be offered for
transportation in commerce without
labels.
SP9610......................... Operational Highway/Rail/ Authorizes transportation in 11
Shipper/Other. commerce of certain empty
packagings containing residues of
Class 1 smokeless powders without
complete shipping papers and
placarding.
SP9874......................... Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors or instrumentation and
signaling systems such as sensors,
alarms, and electronic
surveillance equipment, to observe
the loading and/or unloading
operations of hazardous materials
from production control centers in
lieu of personnel remaining within
25 feet of the cargo tanks.
SP10597........................ Operational Highway/Rail/ Authorizes manufacture, marking and 1
Shipper/Other. sale of temperature controlled
equipment for use in motor
vehicles engaged in transportation
in commerce of Class 3 liquids or
Division 2.1 gases.
SP10705........................ Operational Highway/Rail/ Authorizes transportation in 2
Shipper/Other. commerce of packages containing
acrolein, stabilized, Division
6.1, to be exempted from the
segregation requirements, when
shipped by highway.
SP10803........................ Operational Highway/Rail/ Authorizes manufacture, marking, 1
Shipper/Other. sale and use of temperature
controlled equipment for use in
motor vehicles engaged in
transportation of Class 3 and
Class 2.1 materials.
SP10882........................ Operational Highway/Rail/ Authorizes manufacture, marking, 1
Shipper/Other. sale and use of temperature
controlled equipment for use in
motor vehicles engaged in
transportation of Class 3 and
Class 2.1 materials.
SP11043........................ Operational Highway/Rail/ Authorizes transportation in 79
Shipper/Other. commerce of Division 2.3 materials
on the same transport vehicle with
materials classed as Division 2.1,
Class 3, Class 4, Class 5, and
Class 8.
SP11055........................ Operational Highway/Rail/ Authorizes transportation in 8
Shipper/Other. commerce of certain hazardous
materials that meet the criteria
for Division 6.1, PG I, Hazard
Zone A in combination packages and
provides relief from the
segregation requirements.
SP11078........................ Operational Highway/Rail/ Authorizes transportation in 2
Shipper/Other. commerce of certain nickel-cadmium
batteries each containing no more
than 10 ml of liquid potassium
hydroxide, a Class 8 material, as
not subject to the HMR.
SP11151........................ Operational Highway/Rail/ Authorizes transportation in 1
Shipper/Other. commerce of combination packages
containing hazardous wastes that
are poisonous by inhalation,
Division 6.1, PG I, Hazard Zone A,
in the same transport vehicle with
packages containing hazardous
materials assigned to Class 3,
Class 8 or Divisions 4.1, 4.2,
4.3, 5.1, 5.2.
SP11197........................ Operational Highway/Rail/ Authorizes transportation in 3
Shipper/Other. commerce by private carrier of
restricted quantities of hazardous
materials that are authorized for
exception in column 8A of the HMT,
excluding Class 1, Class 7 and
Divisions 6.1 and 6.2.
SP11202........................ Operational Highway/Rail/ Authorizes transportation in 1
Shipper/Other. commerce of certain hazardous
materials across a public road,
from one part of a plant to
another, as essentially not
subject to parts 172 and 173.
SP11356........................ Operational Highway/Rail/ Authorizes reassignment of certain 3
Shipper/Other. high viscosity flammable liquids
from Packing Group II to III for
packagings with a capacity greater
than 30L.
SP11373........................ Operational Highway/Rail/ Authorizes transportation in 29
Shipper/Other. commerce of Division 4.2 (self-
heating) materials in Packing
Group II or III on the same
transport vehicle with Class 8
liquids when the materials are
appropriately separated.
[[Page 3645]]
SP11458........................ Operational Highway/Rail/ Authorizes transportation in 16
Shipper/Other. commerce of display packs of
consumer commodity packages or
limited quantities packages that
exceed the 30 kg gross weight
limit.
SP11470........................ Operational Highway/Rail/ Authorizes transportation in 34
Shipper/Other. commerce of shrink wrapped pallets
containing boxes of waste ORM-D
materials with the word ``WASTE''
marked on the outside of the
pallet instead of on each
individual box.
SP11666........................ Operational Highway/Rail/ Authorizes transportation in 13
Shipper/Other. commerce of green graphite
products on open flat-bed truck
trailers, rail flat cars,
intermodal freight containers, and
when unitized by banding to wooden
runners or pallets.
SP11811........................ Operational Highway/Rail/ Authorizes transportation in 4
Shipper/Other. commerce of various household
wastes without having the quantity
and unit measurement shown on the
shipping paper during local pick-
up operations.
SP11984........................ Operational Highway/Rail/ Authorizes transportation in 17
Shipper/Other. commerce of certain unapproved
chemical oxygen generators with
only one positive means of
preventing unintentional actuation
of the generator and without the
required approval number marked on
the outside of the package.
SP12002........................ Operational Highway/Rail/ Authorizes unloading of tank cars 1
Shipper/Other. containing Class 3 materials
utilizing an alternate procedure
to remove frozen liquid from
bottom outlet valves.
SP13190........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors to observe the loading
operations of anhydrous ammonia
from a remote control station in
place of personnel remaining
within 7.62 meters (25 feet) of
cargo tank motor vehicles.
SP13199........................ Operational Highway/Rail/ Authorizes transportation in 1
Shipper/Other. commerce of reconditioned
(``used'') refrigeration units
under the provisions of Sec.
173.306(e).
SP13343........................ Operational Highway/Rail/ Authorizes transportation in 1
Shipper/Other. commerce of certain wetted
Division 1.1D explosive substances
in heated cargo vehicles when they
would likely freeze during
transport.
SP13424........................ Operational Highway/Rail/ Authorizes use of video cameras and 2
Shipper/Other. monitors to observe the loading
and unloading operations of
various hazardous materials from a
remote control station in place of
personnel remaining within 7.62
meters (25 feet) of cargo tank
motor vehicles.
SP13484........................ Operational Highway/Rail/ Authorizes DOT specification MC 2
Shipper/Other. 330, MC 331 and MC 338 cargo tank
motor vehicles to be loaded with
certain Division 2.2 liquefied
gases using specially designed
hoses in lieu of full time
attendance by a qualified person
during loading operations.
SP13959........................ Operational Highway/Rail/ Authorizes use of a video camera 1
Shipper/Other. and monitor to observe the loading
incidental to movement or
unloading incidental to movement
of anhydrous ammonia from a remote
control room in place of personnel
remaining within 25 feet of the
cargo tank motor vehicle.
SP14141........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors to observe the loading
incidental to movement or
unloading incidental to movement
of certain Class 3, 8, and 9
materials in place of personnel
remaining within 25 feet of a
cargo tank motor vehicle.
SP14150........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors to observe the loading
and unloading operations of
certain Class 3 and Class 8
hazardous materials from a remote
control station in place of
personnel remaining within 7.62
meters (25 feet) of cargo tank
motor vehicles.
SP14335........................ Operational Highway/Rail/ Authorizes transportation in 3
Shipper/Other. commerce of Division 2.3 Zone A
materials on the same motor
vehicle with DOT specification
packagings containing the residues
of Divisions 2.1, 2.3, 4.3, 5.1,
and Classes 3 and 8 materials.
SP14447........................ Operational Highway/Rail/ Authorizes DOT specification cargo 1
Shipper/Other. tank motor vehicles containing
certain Division 2.2; 5.1; and
6.1; Class 3 and 8 hazardous
materials to be loaded/unloaded
using specially designed hoses in
lieu of being attended by a
qualified person during loading
and unloading operations.
SP14525........................ Operational Highway/Rail/ Authorizes transportation in 2
Shipper/Other. commerce of certain used
diatomaceus earth filter material
not subject to the HMR, except for
shipping papers and certain
marking requirements.
SP14618........................ Operational Highway/Rail/ Authorizes manufacture, marking, 1
Shipper/Other. sale, and use of temperature
controlled equipment for use in
motor vehicles engaged in the
transportation in commerce of
Class 3 liquids or Division 2.1
gases.
SP14680........................ Operational Highway/Rail/ Authorizes use of video cameras and 2
Shipper/Other. monitors to observe the loading
incidental to movement or
unloading incidental to movement
of spent sulfuric acid in place of
personnel remaining within 25 feet
of a cargo tank motor vehicle.
SP14726........................ Operational Highway/Rail/ Authorizes manufacture, marking, 1
Shipper/Other. sale, and use of temperature
controlled equipment for use in
motor vehicle transportation of
Class 3 and Division 2.1 materials.
[[Page 3646]]
SP14822........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors or instrumentation and
signaling systems such as sensors,
alarms, and electronic
surveillance equipment, to observe
the loading and unloading
operations of hazardous materials
from production control centers in
lieu of personnel remaining within
25 feet of the cargo tanks.
SP14827........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors to observe the loading
incidental to movement or
unloading incidental to movement
of certain corrosive materials in
place of personnel remaining
within 25 feet of a cargo tank
motor vehicle.
SP14840........................ Operational Highway/Rail/ Authorizes use of video cameras and 1
Shipper/Other. monitors to observe the loading
incidental to movement or
unloading incidental to movement
of certain Class 8 materials in
place of personnel remaining
within 25 feet of a cargo tank
motor vehicle.
----------------------------------------------------------------------------------------------------------------
Non-Bulk Packaging Specifications/IBCs
----------------------------------------------------------------------------------------------------------------
SP6614......................... Non-Bulk Packaging Authorizes use of polyethylene 11
Specifications/IBCs. bottles placed in a polyethylene
crate for transportation in
commerce of certain Class 8
corrosive materials (NA1760,
UN3266, UN3264, UN3265, UN1791,
UN1789, and UN2796).
SP8230......................... Non-Bulk Packaging Authorizes transportation in 4
Specifications/IBCs. commerce of Packing Group I and II
nitric acids in certain
combination packagings.
SP9722......................... Non-Bulk Packaging Authorizes manufacture, marking, 2
Specifications/IBCs. sale and use of UN1H1 plastic
drums to be used for
transportation in commerce of
nitric acid with not more than 40%
nitric acid.
SP11602........................ Non-Bulk Packaging Authorizes transportation in 11
Specifications/IBCs. commerce of certain Division 4.3
materials contained in sift-proof
closed bulk packagings. Water
reactive solid, n.o.s. (contains
magnesium, magnesium nitrides)
4.3, UN2813, PG II or III.
SP11624........................ Non-Bulk Packaging Authorizes transportation in 114
Specifications/IBCs. commerce by motor vehicle, rail
freight and cargo vessel of
certain waste paints and paint
related materials, Class 3, in
metal or plastic pails, packed in
cubic yard boxes, dump trailers,
and roll-off containers.
SP12030........................ Non-Bulk Packaging Authorizes transportation in 1
Specifications/IBCs. commerce of battery fluid, acid,
packaged with a dry storage
battery in a UN4G fiberboard box
with a maximum gross weight not
over 37.0 kg which exceeds the
weight limitation.
SP12335........................ Non-Bulk Packaging Authorizes transportation in 8
Specifications/IBCs. commerce of certain Division 1.1D
and 1.4D detonating cords without
the ends being sealed in
alternative packaging.
SP12920........................ Non-Bulk Packaging Authorizes transportation in 19
Specifications/IBCs. commerce of certain pyrophoric
materials in a combination package
consisting of UN1A2 outer package
and a UN1A1 inner package.
SP13052........................ Non-Bulk Packaging Authorizes manufacture, mark, sale 1
Specifications/IBCs. and use of UN11G intermediate bulk
containers (IBCs) for
transportation in commerce of
waste paint and related materials.
SP13217........................ Non-Bulk Packaging Authorizes transportation in 1
Specifications/IBCs. commerce of gasoline in non-DOT
specification packages known as
gasoline dispensers.
SP13548........................ Non-Bulk Packaging Authorizes transportation in 125
Specifications/IBCs. commerce of lead acid batteries
and packages of battery acid (with
two different UN numbers) on the
same vehicle.
SP13796........................ Non-Bulk Packaging Authorizes transportation in 1
Specifications/IBCs. commerce of phosphorus, yellow,
under water in alternate packaging.
SP14137........................ Non-Bulk Packaging Authorizes transportation in 1
Specifications/IBCs. commerce of certain hydrochloric
acid solutions in UN31H1 or
UN31HH1 intermediate bulk
containers (IBCs).
SP14213........................ Non-Bulk Packaging Authorizes manufacture, marking, 1
Specifications/IBCs. sale and use of UN1H1 plastic
drums to be used for
transportation in commerce of
nitric acid with not more than 40%
nitric acid.
SP14712........................ Non-Bulk Packaging Authorizes manufacture, marking, 1
Specifications/IBCs. sale, and use UN11G fiberboard and
UN13H4 woven plastic, coated and
with liner flexible intermediate
bulk containers (IBCs) for use as
the outer packaging for certain
Class 3 waste paints.
SP15235........................ Non-Bulk Packaging Authorizes manufacture, mark, sale 1
Specifications/IBCs. and use of UN 11G fiberboard
intermediate bulk containers
(IBCs) for use as the outer
packaging for certain Class 3
waste paints and waste paint
related material.
SP15373........................ Non-Bulk Packaging Authorizes manufacture, mark, sale 1
Specifications/IBCs. and use of the specially designed
combination packagings for
transportation in commerce of
certain Class 4.3 materials
without hazard labels or placards,
with quantity limits not exceeding
25 grams.
----------------------------------------------------------------------------------------------------------------
IV. Public Comments
In the NPRM, PHMSA welcomed comments concerning its proposed
amendments. Specifically, PHMSA was interested in comments from SP
holders (both those deemed suitable and those deemed not suitable for
adoption) that are reviewed for this rulemaking.
[[Page 3647]]
For holders of SPs deemed suitable for adoption, PHMSA requested
comment on our determination. We stated that we were particularly
interested in comments that confirm or refute the suitability, safety,
and general applicability of the SPs. PHMSA also solicited comments on
the regulatory text proposed in this proceeding. Specifically, PHMSA
was interested in comments that address whether the proposed regulatory
text accurately encompasses the requirements of the SP.
For holders of SPs deemed not suitable for adoption, PHMSA also
requested comment on our determination. We stated that we were
particularly interested in comments that confirm or refute the
suitability, safety, and general applicability of the SPs. We asked
that if you are a holder of a SP that was not proposed to be adopted
but believe it should be, you should submit material to support such an
argument. Specifically, PHMSA requested:
Information and arguments that support the proposed
adoption including technical and scientific data;
The impact of the proposed adoption including cost and
benefits;
The frequency of shipments made under the SP;
The frequency of hazardous materials incidents (such as
those described in
Sec. Sec. 171.15 and 171.16) occurring during shipments made under
the SP; and
Proposed regulatory text.
Lastly, PHMSA requested comment as it considers a future proposed
requirement for a SP applicant to provide potential regulatory text as
part of each SP application.
In response to the January 30, 2015 NPRM, PHMSA received 22 sets of
public comments. All were supportive of PHMSA's actions to reduce the
number of active SPs. Specifically, commenters to the NPRM were as
follows in Table 9:
Table 9--NPRM Commenters
------------------------------------------------------------------------
Docket reference (http://
Commenter www.regulations.gov)
------------------------------------------------------------------------
PCTI Puerto Rico Inc. (PCTI)............. PHMSA-2013-0042-003
Pepsi Cola Sales and Distribution, Inc. PHMSA-2013-0042-004
(PCSD)..................................
United Parcel Service (UPS).............. PHMSA-2013-0042-006
DS Container (DSC)....................... PHMSA-2013-0042-007
Mauser USA (Mauser)...................... PHMSA-2013-0042-009
Gulf Coast Chemical LLC (Gulf Coast)..... PHMSA-2013-0042-010
Estes-Cox Corporation (Estes-Cox)........ PHMSA-2013-0042-011
Arkema Inc. (Arkema)..................... PHMSA-2013-0042-013
Veolia ES Technical Solutions, LLC PHMSA-2013-0042-015
(Veolia)................................
Council on Safe Transportation of PHMSA-2013-0042-016
Hazardous Articles (COSTHA).............
Rigid Intermediate Bulk Container PHMSA-2013-0042-017
Association of North America (RIBCA-NA).
Air Products and Chemicals, Inc. (Air PHMSA-2013-0042-018
Products)...............................
Battery Council International (BCI)...... PHMSA-2013-0042-019
Institute of Makers of Explosives (IME).. PHMSA-2013-0042-020
The Chlorine Institute (CI).............. PHMSA-2013-0042-021
Dangerous Goods Advisory Council (DGAC).. PHMSA-2013-0042-022
Eli Lilly and Company (Eli).............. PHMSA-2013-0042-023
Consumer Specialty Products Association PHMSA-2013-0042-024
(CSPA)..................................
Council on Safe Transportation of PHMSA-2013-0042-025
Hazardous Articles (COSTHA).............
Dow Chemical Company (Dow)............... PHMSA-2013-0042-026
American Coatings Association (ACA)...... PHMSA-2013-0042-027
Barlen and Associates, Inc. (Barlen)..... PHMSA-2013-0042-028
------------------------------------------------------------------------
A. General/Administrative
DSC expresses its concern about the disposition of SPs adopted into
the HMR. It asks what happens to SPs once they are adopted into the
HMR, and if there will be a phase-in period. DSC also asks, if the
adoption of a SP is unacceptable to a grantee or grantees, will the SP
still be an available option? It also asks will this rulemaking affect
the application of future SPs.
PHMSA notes that as the intention of this rulemaking is to adopt
the provisions of certain SPs into the HMR, those affected SPs will be
allowed to expire. However, PHMSA is providing a one-year effective
date to allow current grantees sufficient time to transition from the
provisions of their SPs to the new requirements being adopted into the
HMR. In addition, if the adoption of a SP proves to be unacceptable to
a grantee, a renewal or modification in accordance with 49 CFR 107.121
will still be allowed. This rulemaking will not affect the application
for future SPs as the requirements to apply for a SP are not being
revised, and the SP program will continue as permitted by law. Air
Products asks if PHMSA will provide a timeline/updates for ``other''
rulemaking proceedings that may have SPs under consideration for
adoption in the HMR. PHMSA will continue to provide updates pertaining
to other rulemaking proceedings that may have SPs under consideration
for adoption into the HMR through its existing channels which include
the semi-annual agenda, rulemaking activities, and Federal Register
notices.
In the NPRM, PHMSA solicited input regarding applicants being
required to submit proposed regulatory text with SP applications. PHMSA
acknowledges mixed support from affected entities on this issue. For
example, Veolia and Dow support adoption of such policy while COSTHA
and ACA do not. IME supports such policy as an option for an applicant.
IME is concerned that PHMSA will conduct SP reviews for potential
adoption on a biennial basis rather than an annual basis as implied
through MAP-21 legislation. As noted elsewhere in this preamble, PHMSA
intends to perform SP evaluations on an annual basis; however,
rulemaking actions as a result may take more time as necessary.
Lastly, PHMSA's final regulations issued in its final rule entitled
``Hazardous Materials: Special Permit and Approvals Standard Operating
Procedures and Evaluation Process,'' under Docket No. PHMSA-2012-0260
(HM-233E; 9/10/15, 80 FR 54418, FR Doc. 2015-22617), contain minor
[[Page 3648]]
editorial errors in two definitions in adopted in Sec. 107.1
concerning special permits and approvals. PHMSA is correcting those
definitions in this final rule.
B. Cylinders--General
No comments were received regarding the SPs proposed for adoption
under this category. PHMSA did, however, receive comments requesting
reconsideration of certain SPs not proposed for adoption.
Comments Requesting Reconsideration
COSTHA requests that reconsideration be given to adopt portions of
SPs 12726 and 15277 (aircraft fire extinguishers) to allow them to be
described in transportation as UN1044, Fire extinguishers. PHMSA notes
this issue is under consideration in another rulemaking action under
docket PHMSA-2011-0140 (RIN 2137-AE80 (HM-234)). COSTHA also requests
that reconsideration be given to adopt SP 10898 in Sec. 173.306(f)
related to accumulators. Because neither SP was proposed for adoption
in the NPRM, neither SP is being adopted in this final rule.
C. Cylinders--NDT/Aerosols
CSPA is supportive of the adoption of SP 11296 and its expansion
beyond flammable aerosols only (as proposed in the NPRM).
CSPA and DSC generally support adoption of SP 12573 (and the
consolidation with SP 13581) as proposed. They are, however, concerned
with the supposed arbitrary increase in reference temperature and
pressure with the new DOT 2Q1 standard currently authorized for
refrigerant gases in Sec. 173.304. DSC suggests a single requirement
of 210 psig at 55 [deg]C (131 [deg]F). It also suggests that such
arbitrary actions if adopted could increase the number of SP
applications submitted as a result. PHMSA recognizes the commenters'
concerns; however, changing the reference temperature for the
refrigerant gases to 54.4 [deg]C (130 [deg]F) would make section
173.304(d) inconsistent with the other sections for the filling of
gases. As noted in the NPRM, PHMSA sought to have consistency where
some sections referred to 54.4 [deg]C (130 [deg]F) and some to 55
[deg]C (131 [deg]F). PHMSA is therefore keeping the reference
temperature used for maximum pressure in a container at 55 [deg]C (131
[deg]F) as proposed in the NPRM. In order to address the commenters'
concerns, PHMSA is raising the proposed maximum pressure authorized in
the new DOT 2Q1 container to 210 psig at 55 [deg]C (131 [deg]F) as
authorized in Sec. Sec. 173.304 and 173.306. The burst pressure of the
DOT 2Q1 will have to be raised slightly accordingly to provide for the
same safety factor. This will be discussed in a later section.
CSPA and DSC generally support adoption of the consolidated SPs
7951, 13601, and 14503 as proposed. They are again, however, concerned
with the increase in reference temperature and pressure. CSPA is also
concerned that the new relationship proposed between a pressure relief
device (PRD) and an end expansion device, and the arbitrary upper
boundaries adopted should instead be simply required to operate prior
to burst. CSPA and DSC suggest as an alternative that ``the requirement
could be defined differently for an end expansion device specifically
versus the PRD using the language in SP 13601 that requires that the
end buckle before burst and that the container not burst below 270
psig.''
CSPA and DSC correctly point out that the methodology used in the
``if/then'' table for the use of a DOT 2P or DOT 2Q aerosol on page
5439 [of the NPRM] is actually reversed and would lead to not allowing
(by choice) a higher integrity container as a result. PHMSA agrees with
the commenters and is revising the tables in Sec. 173.306 accordingly.
CSPA generally supports adoption of the new DOT 2Q1 container as
proposed.
DSC suggests that the new DOT 2P1 specification should be limited
to refrigerated foodstuffs only as prescribed in SPs 13601, 14503, and
7951. Further, DSC recommends that the new DOT 2P1 specification not be
expanded to authorize Division 2.1 flammable gases. However, in its
comments, DSC does not provide support as to why the new DOT 2P1
specification should be limited to refrigerated foodstuffs and Division
2.2 (nonflammable) gases only.
DSC recommends that foodstuffs in refrigerated DOT 2P1 cans be
excepted, as they currently are under the SPs, from the hot water bath
test. PHMSA notes that refrigerated foodstuffs in aerosol cans under
Sec. 173.306(b) will continue to be excepted from hot water bath
testing when the three SPs are adopted in the HMR.
CSPA supports consolidation of SPs 14429, 14623, 14625, 14627,
14723, 14724, 14786, 14842, 14887, 14953, 15135, 15265, 15427, and
15972 (hot water bath test alternative), SP 14440 (weight test), and SP
14544 (weight and leakage test) as proposed.
DSC is concerned as to what will happen to SPs once adopted into
the HMR and whether there will be a phase-in period. It asks because of
substantial costs and other impacts due to relabeling of product, etc.
Dow and CSPA support adoption of SP 12995, with Dow asking that
sufficient time be allotted to deplete existing inventory.
In response, PHMSA notes there is a one-year transition period
provided to affected entities in this final rule. Further, as
prescribed in Sec. 173.23(h), a packaging that is permanently marked
with a SP number, ``DOT-SP'' or ``DOT-E,'' for which the provisions of
the SP have been incorporated into the HMR may continue to be used for
the life of the packaging without obliterating or otherwise removing
the SP number.
Comments Requesting Reconsideration
CSPA strongly asserts that reconsideration should be given to
adopting SP 11516, which authorizes transportation in commerce of
aerosols that do not meet the HMR definition of an aerosol (e.g.,
expels propellant only). CSPA suggests that PHMSA should adopt the
international United Nations (UN) and the Globally Harmonized System
(GHS) definition of an aerosol. In its comments, CSPA claims that DOT
committed to adopting the international aerosol definition while it was
involved with developing the GHS flammability standard. CSPA also
states ``it is vitally important that DOT maintain 11516 (and other
related SPs) as is.''
Although PHMSA appreciates the comments pertaining to SP 11516,
until such a time that PHMSA participates in an open and transparent
debate on this issue (redefining the term ``aerosol''), SPs such as SP
11516 and the like will remain valid under current policy and
definitions.
D. Cargo Tanks/Rail Cars/Portable Tanks
No comments were received regarding the SPs proposed for adoption
under this category. PHMSA did, however, receive comments requesting
reconsideration of certain SPs not proposed for adoption.
Comments Requesting Reconsideration
In its comments, The Chlorine Institute (CI) recommends that
reconsideration be given to adopt SP 9694 and 10457. These SPs
authorize the transportation in commerce of chlorine contained in MC
331 cargo tanks equipped with angle valves, excess flow valves and
pressure relief valves not presently authorized in the HMR. Because
neither SP was proposed for adoption in the NPRM, neither SP is being
adopted in this final rule.
In its comments, The CI recommends that reconsideration should be
given to
[[Page 3649]]
adopt SP 15647. This SP authorizes the retesting of certain DOT
specification and non-DOT specification multi-unit tank car tanks
without approval from the Association of American Railroads (AAR).
PHMSA notes that SP 15647 is under consideration for adoption into the
HMR in a separate advance notice of proposed rulemaking (ANPRM) under
docket PHMSA-2012-0082 (HM-251).
Lastly, the CI recommends that reconsideration should be given to
adopt SP 9166 and SP 11903 under Petition for Rulemaking (P-1608) and
related SPs 10878, 12516, 14275, 14277, 14779, and 15552. These SPs
authorize the manufacture, marking, sale, and use of a non-DOT
specification glass fiber reinforced plastic (GFRP) cargo tank
conforming with all regulations applicable to a DOT specification 407/
412 for transportation in commerce of certain hazardous materials.
PHMSA notes it is working to develop a uniform standard for FRP cargo
tanks and will address this issue in a future rulemaking.
E. Operational Air/Vessel
COSTHA supports future consideration of SP 11110 under Petition for
Rulemaking P-1610. As previously noted, COSTHA submitted a petition for
rulemaking under P-1610 to adopt the provisions of SP 11110 into the
HMR. This SP authorizes cargo aircraft operators to stow Division 1.4S
and Class 8, PG III materials in inaccessible cargo locations in excess
of the limitations specified in Sec. 175.75(c). This petition has been
accepted by PHMSA for consideration in a future rulemaking; however,
more time is needed to research the potential impact of changes to
Sec. 175.75 and to coordinate this review with the appropriate
parties, including our modal partners.
Based on comments from PCSD, proposed Special provision ``W11'' in
Sec. 172.102 is being replaced by revising Sec. 176.800(a) to allow
Class 8 (corrosive) materials that are also foodstuffs or foodstuff
ingredients intended for human consumption to not be considered
incompatible for segregation purposes in conformance with SP 11691.
Comments Requesting Reconsideration
Some commenters recommended that reconsideration be given to adopt
SP 11502 (use of International Civil Aviation Organization Technical
Instructions (ICAO TI) for highway shipments). In their comments,
COSTHA and UPS firmly support adoption and provide justification as to
why the SP should be adopted. However, PHMSA notes SP 11502 is under
consideration for adoption into the HMR in a separate, broader, and yet
unassigned air-specific rulemaking action.
Arkema recommends that reconsideration should be given to adopt SP
12879 into the HMR. This SP authorizes the transport of IBCs containing
combustible liquids without placards or identification numbers in
sealed freight containers consigned for export. Because SP 12879 was
not proposed for adoption in the NPRM, the SP is not being adopted in
this final rule; however, we may reconsider its codification in a
future proceeding as appropriate.
F. Operational Highway/Rail/Shipper/Other
PHMSA acknowledges COSTHA's support for the adoption of petitions
for rulemaking P-1607 (SP 11458) and P-1611 (SP 11470) into the HMR in
this proceeding.
IME supports the adoption of SP 4850 as proposed. This SP
authorizes the transportation in commerce by motor vehicle, rail
freight, cargo vessel, and cargo aircraft of limited quantities of
certain approved explosive articles (UN0237, charges, shaped, flexible,
linear; and UN0104, cord, detonating, mild effect or fuse, detonating,
mild effect metal clad) re-classed as Division 1.4D in prescribed
packagings, subject to certain special provisions.
Veolia supports the adoption of SP 11055. Further, Veolia supports
adoption of SP 11470 with one major modification--the HMR should not be
limited to ``expired'' products but rather should include all consumer
commodities shipped for disposal/recycling under manufacturer recalls,
off-spec/unwanted/unneeded product, etc. PHMSA agrees with Veolia and
is revising Sec. 173.306(k) accordingly.
COSTHA and DGAC support the adoption of SPs 11352, 12207, 12306,
13165, and 14945. However, according to COSTHA, the proposed regulatory
text in Sec. 177.820 appears to be more restrictive than the
exceptions currently in Sec. 171.1(d)(4). After further consideration,
we agree with COSTHA and are not adopting the five SPs in this final
rule as proposed in the NPRM.
Dow supports the adoption of SP 9874, SP 14822, and the eight
related SPs. In its comments, Dow supports codification of the SPs but
has specific concerns: (1) SP 9874 and 14822 authorize instrumentation
and signaling systems such as sensors, alarms, and electronic
surveillance equipment in addition to video monitoring; (2) SP 9874 and
14822 do not require a video camera with a ``motorized zoom lens
capable of panning and zooming from the remote control station''; (3)
SP 9874 and 14822 do not require that the view capability must include
the entire containment area; and (4) Dow wants assurance that the
attendance requirements in Sec. 177.834 (i) apply to motor carriers
only. We agree that Dow's comments have merit and, in this final rule,
except for number (4), the regulatory text in Sec. 177.834(i) is
revised accordingly. Regarding issue number (4), long-standing
interpretations preclude the need to revise the attendance
applicability provisions of the HMR. As a result of Dow's concerns,
Sec. 177.834 (i) is revised accordingly in this final rule.
In its comments, Eli expresses it support for the adoption of SP
14150 in Sec. 177.834(i)(3)(ii) as proposed. SP 14150 authorizes use
of video cameras and monitors to observe the loading and unloading
operations of certain Class 3 and Class 8 hazardous materials from a
remote control station in place of personnel remaining within 7.62
meters (25 feet) of cargo tank motor vehicles. Lastly, PCTI supports
adoption of SP 11352 as proposed in Sec. 177.820.
Veolia supports the adoption of SP 11043. However, it notes that
the regulatory text proposed in Sec. 177.840(a)(3)(i) should be
revised to require a 4-foot separation rather than a 5-foot separation
for consistency with the segregation spacing requirements found in
Sec. 173.12(e). We agree with Veolia's comment and are revising Sec.
177.840(a)(3)(i)(C) accordingly.
Veolia supports adoption of SP 11984 with one major modification--
the HMR should require flame-proof outer packaging for chemical oxygen
generators shipped with only one positive means of preventing
unintentional activation as expressed in concern for equivalent level
of safety in proposed SP modification in August 2011. After additional
review, in this final rule, we are adopting the provisions of SP 11984
as proposed into Sec. 173.168.
In the NPRM, PHMSA proposed to add Special Provision 383 to adopt
SP 11356. This SP authorizes certain materials meeting the conditions
for high viscosity flammable liquids specified in Sec.
173.121(b)(1)(i), (b)(1)(ii), and (b)(1)(iv), to be reassigned to
Packing Group (PG) III for transportation by motor vehicle. The SP
prescribes packaging, capacity limitations, and load securement
requirements. We proposed to adopt the provisions of the SP in its
entirety in this new special provision for the following entries:
Coating solution (UN1139, PG II) and paint (UN1263, PG II). In its
comments,
[[Page 3650]]
ACA requests that PHMSA expand the materials authorized for
reclassification to include: (1) UN1866, Resin solution, PG II; (2)
UN1210, Printing ink, PG II; and (3) UN1133, Adhesives, PG II. We agree
with ACA and are revising the HMT for the requested entries
accordingly.
In the NPRM, we proposed to add a new paragraph (h) to Sec. 173.12
to adopt the provisions of SP 11470 in its entirety. In its comments,
ACA is concerned that ``stretch-wrapped'' pallets would not be able to
take advantage of the exceptions provided for ``shrink-wrapped''
pallets. Further, ACA suggests that the proposed regulatory text limits
the type of packages to ``boxes.'' We agree and are revising Sec.
173.12(h) to explicitly allow ``stretch-wrapped'' pallets and any
authorized type of packaging.
Section 174.67 establishes specific operational requirements for
railroad tank car unloading. For combustible liquids or Class 3 liquid
petroleum distillate fuels, SP 12002 authorizes clearing frozen liquid
blockages from the outlet by attaching a fitting to the outlet line and
applying nitrogen at a pressure of 50 to 100 psi. In the NPRM, we
proposed to revise paragraph (g) to Sec. 174.67 to adopt the
provisions of SP 12002 in its entirety. In its comments, ACA recommends
that the use of nitrogen should be permitted ``at a pressure of up to
100 psi'' for clarity. We agree with ACA and are revising Sec.
174.67(g) accordingly.
In its comments, DGAC supports adoption of SP 11666 as Sec.
172.102(c)(1), Special Provision 384. It does, however, comment on the
use of the word ``sifting'' which should actually be ``shifting'' and,
further, the SP permits stacking two or more levels high to achieve
maximum allowable utilization of the designated vehicle, rail car
weight, or intermodal freight container weight or vessel hold volume.
We agree with DGAC's comments and the special provision is revised
accordingly.
DGAC supports the adoption of SP 14525 and correctly points-out
some discrepancies in preamble discussion of its adoption in new Sec.
172.102(c)(3), Special Provision B130. We agree with DGAC's comments
and revise the preamble discussion and regulatory text accordingly.
Comments Requesting Reconsideration
IME and COSTHA firmly support that reconsideration should be given
to adopt SP 14282. This SP authorizes transportation in commerce of
certain detonators, detonator assemblies, detonators for ammunition,
detonating fuses and igniting fuses on the same motor vehicle with any
other Class 1 explosives. Because SP 14282 was not proposed for
adoption in the NPRM, the SP is not being adopted in this final rule.
Veolia comments that reconsideration should be given to adopt SP
12998. This SP authorizes the transportation in commerce of lab packs
containing materials that are not waste materials by private or
contract carrier from one laboratory to another within the same
company. Because SP 12998 was not proposed for adoption in the NPRM,
the SP is not being adopted in this final rule.
Veolia comments that reconsideration should be given to adopt SP
12102. This SP authorizes transportation in commerce of certain
unapproved desensitized explosives. Because SP 12102 was not proposed
for adoption in the NPRM, the SP is not being adopted in this final
rule.
Veolia comments that reconsideration should be given to adopt SP
13179. This SP authorizes transportation in commerce of certain
approved lighters which have been removed from their inner packaging
and are being sent for disposal. Because the SP indicated Code 5
(already adopted or otherwise covered under current regulations as the
reason it was considered not suitable for adoption), Veolia asserts
PHMSA will terminate the SP and therefore, its provisions either need
to be adopted into the HMR in this rulemaking or the SP should not be
terminated. We sincerely apologize for any confusion this may have
caused as we mistakenly miscoded SP 13179 in the NPRM. In hindsight, SP
13179 should have been a Code 2 or 3 as not suitable for adoption.
Further, because SP 13179 was not proposed for adoption in the NPRM,
the SP is not being adopted in this final rule nor do we intend to
terminate it at this time.
For highway transportation by private carrier, SP 11197 provides
relief from the requirement to display the limited quantity marking on
packages containing materials assigned to PG II and III and prepared in
accordance with the limited quantity requirements in Part 173. In its
comments, ACA claims the regulatory text is not clear regarding its
application but did not provide alternative language. Consequently, the
language is adopted as proposed.
Gulf Coast, RIBCA-NA, and CI recommend that reconsideration should
be given to adopt SP 12412 into the HMR as there are 322 companies as
grantees. This SP authorizes discharge of liquid hazardous materials
from certain UN intermediate bulk containers (IBCs) and DOT
specification 57 portable tanks without removing them from the vehicle
on which they are transported. Because SP 12412 was not proposed for
adoption in the NPRM, the SP is not being adopted in this final rule.
Estes-Cox firmly supports the adoption of SP 7887 and comments that
reconsideration should be given. This SP authorizes certain Class 1
articles in small amounts to be reclassed as Division 4.1 flammable
solid, organic, n.o.s. It applies to small ``single-use expendable'' or
``reloadable'' rocket motors first classed as Division 1.4C or 1.4S
(NA0323 or NA0276) shipped with or without their igniters classed as
Division 1.4G or 1.4S under Sec. 173.56. Because SP 7887 was not
proposed for adoption in the NPRM, the SP is not being adopted in this
final rule.
G. Non-Bulk Packaging Specifications/IBCs
IME supports the adoption of SP 12335, which authorizes
transportation in commerce of certain Division 1.1D and 1.4D detonating
cords without the ends being sealed in alternative packaging.
SP 8230 authorizes the transportation in commerce of PG I and II
nitric acids in certain combination packagings by motor vehicle, rail
freight, cargo vessel and cargo-only aircraft. Specifically, ``Nitric
acid, other than red fuming, with more than 70% nitric acid'' and
``Nitric acid, other than red fuming, with not more than 70% nitric
acid'' is authorized to be transported in inner plastic bottles in
rigid foam plastic receptacles or plastic bags lined with absorbent
material in outer packagings. In its comments, UPS supports adoption of
SP 8230 in Sec. 173.158(j) as proposed.
Section 173.158 provides general requirements and exceptions for
shipments and packagings of nitric acid. In the NPRM, we proposed to
establish a new paragraph (i) to authorize ``Nitric acid of up to 40%
concentration'' in a UN1H1 non-removable head plastic drums with
certain conditions as prescribed in SP 14213. In its comments, Mauser
questioned why SP 9722 was not also proposed for adoption as it is
identical to Greif's SP 14213. After additional review, we agree and in
this final rule are also adopting the provisions of SP 9722 into Sec.
173.158 accordingly.
DGAC supports the adoption of SP 9610 with edits. However, the SP
was revised in November 2014 after review of the SPs as part of this
proceeding. We agree with the revisions made to the SP. Therefore, in
this final rule, we are revising new paragraph Sec. 173.29(f) to
address the DGAC edits and the 2014
[[Page 3651]]
revisions to the SP, specifically, to include fiberboard boxes as
authorized packagings for empty packagings containing the residue of
smokeless powders.
Comments Requesting Reconsideration
IME and COSTHA firmly support that reconsideration should be given
to adopt SP 8451. This SP authorizes transportation in commerce of not
more than 25 grams of solid explosive or pyrotechnic material,
including waste-containing explosives that have an energy density not
significantly greater than that of pentaerythritol tetranitrate (PETN),
classed as Division 1.4E, when packed in a special shipping container.
Because SP 8451 was not proposed for adoption in the NPRM, the SP is
not being adopted in this final rule.
IME firmly supports that reconsideration should be given to adopt
SP 10880. This SP authorizes the transportation in commerce of ammonium
nitrate-fuel oil mixture (ANFO), Division 1.5, in reusable, flexible
intermediate bulk containers (IBCs) type UN 13H3 or UN 13H4 conforming
to Subpart N and O of Part 178. Because SP 10880 was not proposed for
adoption in the NPRM, the SP is not being adopted in this final rule.
IME and COSTHA firmly support that reconsideration should be given
to adopt SP 11156. This SP authorizes transportation in commerce of
NA0331, UN1942 and UN0331 in non-DOT specification multi-wall plastic-
lined paper bags. Because SP 11156 was not proposed for adoption in the
NPRM, the SP is not being adopted in this final rule.
SP 11624 was not proposed for adoption in the NPRM. The SP is in
its fifteenth revision and has 114 grantees. The SP authorizes
transportation in commerce of certain waste Class 3 paint and paint
related material (UN1263; PG II and PG III) contained in metal or
plastic pails further packed in non-specification bulk packagings such
as cubic yard boxes, plastic rigid-wall bulk containers, dump trailers,
and roll-off containers. In their comments, Veolia, ACA, and DGAC
provided substantial justification why reconsideration should be given
to adopt SP 11624 into the HMR. Therefore, after revaluation, SP 11624
and three related packaging SPs (i.e., SP 13052, SP 14712, and 15235)
are adopted as new Sec. 172.102(c)(3), Special Provision B131.
V. Section-by-Section Review by Topic Area
A. Cylinders--General
Part 172
Section 172.102--Special Provisions
Section 172.102(c) lists special provisions applicable to specific
entries in the Hazardous Materials Table (HMT). Special provisions may
contain packaging requirements, conditions or limitations, and
exceptions applicable to particular quantities or forms of hazardous
materials.
In general, non-bulk packagings must be marked with an
identification number and proper shipping name and bear labels
communicating the hazard of the material contained in the package. SP
13544 authorizes the transportation in commerce of DOT Specification
4BA240 cylinders containing liquefied petroleum gas (LPG) and propane
and/or residue of LPG or propane without hazard warnings (i.e., hazard
communication) provided the materials are transported in a closed and
placarded transport vehicle. This SP supports the propane cylinder
exchange programs that accept expended cylinders in exchange for full
cylinders. Cylinders collected during the course of these programs may
not always bear the appropriate hazard markings and labels as required
by the HMR. SP 13544 prescribes certain operational controls to ensure
appropriate hazard communication, driver training, and appropriate
securement of the cylinder on the transport vehicle.
In this final rule, PHMSA is adopting SP 13544 as proposed by
adding new Special Provision, ``N95'' to Sec. 172.102(c)(5) that
excepts cylinders containing UN1075, Liquefied petroleum gas and
UN1978, Propane from marking the identification number and proper
shipping name or bear hazard labels provided certain conditions are
met. Because we did not receive public comment on this amendment,
supportive or otherwise, it is adopted as proposed in the NPRM.
Section 172.400a
Section 172.400a provides exceptions or alternatives to the HMR
labeling requirements under specific circumstances. One such
alternative permits the use of a neckring marking, under certain
conditions, in accordance with the Compressed Gas Association (CGA)
Pamphlet C-7, Guide to Preparation of Precautionary Labeling and
Marking of Compressed Gas Containers, Appendix A, 8th Edition (2004).
Section 172.400a permits the use of a CGA Pamphlet C-7 marking in lieu
of the required 100 mm x 100 mm square-on-point labels on a Dewar flask
meeting the requirements in Sec. 173.320 and on cylinders containing
Division 2.1, 2.2, and 2.3 materials that are not overpacked.
SP 14251 authorizes the transportation of overpacked cylinders,
containing Class 2 materials, with CGA C-7 neckring markings provided
the overpack is labeled in accordance with Sec. 172.400. Additionally,
the CGA petitioned PHMSA (under petition P-1521) to allow cylinders to
display the neckring marking even when overpacked. The petition, if
adopted, would still require the overpack to display the 100 mm x 100
mm square-on-point labels in accordance with 49 CFR Part 172, Subpart
E. The marking prescribed in Appendix A to CGA Pamphlet C-7 provides
useful information in a clear and consistent manner and its widespread
use on cylinders over the course of several years has enhanced its
recognition. The adoption of SP 14251 and CGA's petition would provide
greater flexibility for shipments of cylinders while ensuring adequate
hazard communication. Therefore, PHMSA is revising as proposed Sec.
172.400a by authorizing the transportation of overpacked cylinders
marked in accordance with CGA Pamphlet C-7 provided the overpacks are
properly labeled.
Part 173
Section 173.181
Section 173.181 prescribes authorized packagings for the
transportation of pyrophoric materials (liquids).
SP 14419 authorizes the use of DOT Specification 3AL cylinders
constructed from aluminum alloy 6061-T6 for the transportation of
pyrophoric liquids provided: (1) The cylinders are constructed of 6061-
T6 aluminum; (2) have a minimum marked service pressure of 1800 psig;
(3) have a maximum water capacity of 49 liters; and (4) any preheating
or heating of the cylinders is limited to a maximum temperature of
175[emsp14][deg]F. In this final rule, PHMSA is revising Sec.
173.181(a) as proposed to permit the use of DOT Specification 3AL
cylinders constructed from aluminum alloy 6061-T6, with the same
specified conditions for the transport of pyrophoric materials.
Section 173.193
Section 173.193(b) requires that ``Bromoacetone, Methyl bromide,
Chloropicrin and Methyl bromide mixtures, Chloropicrin and Methyl
chloride mixtures, and Chloropicrin
[[Page 3652]]
mixtures charged with non-flammable, non-liquefied compressed gas be
packaged in DOT Specification 3A, 3AA, 3B, 3C, 3E, 4A, 4B, 4BA, 4BW, or
4C cylinders having not over 113 kg (250 pounds) water capacity
(nominal).''
SP 12301 authorizes the transportation in commerce of Chloropicrin
and Methyl bromide mixtures in DOT 4BW cylinders with water capacity
(nominal) not over 454 kg (1,000 pounds). In this final rule, PHMSA is
adopting as proposed the revisions to Sec. 173.193(b) that allow for
Chloropicrin and Methyl bromide mixtures to be packaged in DOT
specification 4BW cylinders with a water capacity of not over 454 kg
(1,000 pounds).
Section 173.301
Section 173.301 prescribes the general requirements for the use of
cylinders including a list of authorized cylinders, general filling
requirements, valve protection, and pressure relief device
requirements. In the NPRM, we proposed revisions that would amend
certain pressure relief device requirements and permit the use of valve
caps made from a material other than metal as authorized under the
terms of three SPs.
SP 13318 authorizes the transportation in commerce of DOT
Specification 39 cylinders of 75 cubic inches or less volume, without
the PRD in direct communication with the vapor space. PHMSA proposed to
amend paragraph (f)(2) to state that this provision does not apply to
cylinders of 75 cubic inches or less in volume filled with a Liquefied
petroleum gas, Methyl acetylene and Propadiene mixtures, stabilized,
Propylene, Propane or Butane. Because we did not receive public comment
on this amendment, supportive or otherwise, it is adopted as proposed
in the NPRM.
SP 8074 provides an exception from the PRD requirements for a DOT
Specification 3E cylinder up to 12 inches long and 2 inches in diameter
when filled with the following gases and associated quantity limits:
Carbon dioxide, liquefied 0.24L (8 oz.), Ethane 0.12L (4 oz.), Ethylene
(4 oz.), Hydrogen chloride, anhydrous 0.24L (8 oz.), Nitrous oxide
0.24L (8 oz.), Vinyl fluoride, stabilized 0.24L (8 oz.) and
Monochlorotrifluoromethane 0.35L (12 oz.). In the NPRM, PHMSA proposed
to create an additional exception to PRD requirements for DOT-3E
cylinders under limited circumstances in new paragraph Sec.
173.301(f)(7). Because we did not receive public comment on this
amendment, supportive or otherwise, it is adopted as proposed in the
NPRM.
SP 12782 authorizes plastic valve protection caps for certain
Division 2.1, 2.2, and 2.3 materials when the valve protection is
sufficient to prevent leakage when the cylinder, with the valve
installed, is dropped from 2.0 m (7 ft) or more onto a non-yielding
floor, impacting the valve assembly or cap at the orientation most
likely to cause damage. The HMR require that each cylinder with a valve
must have a protective metal cap, other valve protection device, or an
overpack which is sufficient to protect the valve from damage during
transportation. In the NPRM, PHMSA proposed to amend Sec. Sec.
173.40(d) and 173.301(h) to allow for the new valve protection
standard, including the valve cap, to be made from plastic as
authorized in SP 12782. Because we did not receive public comment on
this amendment, supportive or otherwise, it is adopted as proposed in
the NPRM.
Section 173.302a
Sections 173.302, 173.302a, 173.304 and 173.304a prescribe
additional requirements for the transport of non-liquefied (permanent)
and liquefied compressed gases in DOT specification cylinders. These
requirements include authorized cylinders and filling limits. Section
173.302a(b) states that a DOT 3A, 3AA, 3AX, 3AAX, and 3T cylinder may
be filled with a compressed gas, other than a liquefied, dissolved,
Division 2.1, or Division 2.3 gas, to a pressure 10% in excess of its
marked service pressure, subject to certain criteria.
SP 6530 authorizes the transport in commerce of hydrogen and
mixtures of hydrogen with helium, argon, or nitrogen, in certain
cylinders filled to 10% in excess of their marked service pressure. In
the NPRM, PHMSA proposed to add a new paragraph (c) to include this
exception and to redesignate the other paragraphs in this section to
reflect this addition. Because we did not receive public comment on
this amendment, supportive or otherwise, it is adopted as proposed in
the NPRM with the exception of an editorial correction. In the NPRM,
paragraph (c)(3)(ii) stated that cylinders manufactured with chrome
moly steel must have been normalized. The paragraph has been corrected
to state that the steel must have been quenched and tempered, not
normalized. In addition the paragraph (c)(4) the term safety relief
devices has been corrected to pressure relief devices for consistency
with current regulations.
Section 173.304a
In Sec. 173.304a(a)(2), a table provides the maximum filling
densities and permissible cylinder types for certain named gases.
Currently, Sec. 173.304a(a)(2) permits a maximum filling density of
68% for carbon dioxide and nitrous oxide in DOT 3, DOT 3HT2000 and DOT
39 cylinders, and DOT 3A, 3AA, 3AX, 3AAX, 3E, 3T, and 3AL cylinders
with a marked service pressure of 1800 psi.
SP 13599 authorizes additional maximum filling densities for carbon
dioxide and nitrous oxide to include 70.3%, 73.2%, and 74.5%
respectively in DOT 3A, 3AA, 3AX, 3AAX, 3AL, and 3T cylinders with
marked service pressures of 2000, 2265, and 2400 psig, subject to
operational controls. Air Products and Chemicals Inc. (Air Products)
submitted a petition for rulemaking (P-1560) requesting PHMSA revise
Sec. 173.304a(a)(2) to adopt the provisions of SP 13599. In the NPRM,
PHMSA proposed to modify the entries currently in the table in Sec.
173.304a(a)(2) to add additional filling densities for carbon dioxide
and nitrous oxide. Because we did not receive public comment on this
amendment, supportive or otherwise, it is adopted as proposed in the
NPRM.
Part 180, Subpart C
Qualification, Maintenance and Use of Cylinders
The HMR prescribe requirements for the continuing qualification,
maintenance, and periodic requalification of DOT specification
cylinders, DOT SP cylinders, and UN pressure receptacles. These
requirements ensure that cylinders conform to the appropriate
specification and compromised cylinders are not filled with hazardous
materials. The discussion of the proposed amendments includes a
section-by-section review of the current requirements, and a brief
discussion of SPs considered for adoption and proposed amendments.
Section 180.209
Paragraph (e) of Sec. 180.209 authorizes a proof pressure test in
lieu of the volumetric expansion test for 4B, 4BA, 4BW, or 4E cylinders
protected with a corrosion resistant coating and used exclusively for
the gases specified in that paragraph.
SP 12084 expands the list of authorized gases in paragraph (e).
These gases include refrigerated and liquefied gases similar to those
already permitted by Sec. 180.209(e). In the NPRM, PHMSA proposed to
adopt the provisions in SP 12084 by removing the list of authorized
[[Page 3653]]
gases and authorizing the use of the proof pressure test for DOT-4B,
4BA, 4BW, or 4E cylinders protected externally by a suitable corrosion
resistant coating and used exclusively for non-corrosive gases. The
authorized specifications limit the total pressure in the cylinder to
500 psi or less. Because we did not receive public comment on this
amendment, supportive or otherwise, it is adopted as proposed in the
NPRM.
Section 180.213
Cylinders requalified in accordance with the HMR must bear
requalification markings in accordance with Sec. 180.213. As provided
in Sec. 180.213(c), ``The depth of requalification markings may not be
greater than specified in the applicable specification. The markings
must be made by stamping, engraving, scribing or other method that
produces a legible, durable mark.''
SP 14937 allows the use of a label embedded in epoxy in lieu of
other methods prescribed in Sec. 180.213. In the NPRM, PHMSA proposed
to amend paragraph (c) to allow the use of a label embedded in epoxy in
lieu of stamping provided the marking is legible and durable. Because
we did not receive public comment on this amendment, supportive or
otherwise, it is adopted as proposed in the NPRM.
B. Cylinders--Non-Destructive Testing/Aerosols
Part 173
Section 173.304
Section 173.304 prescribes requirements for the filling of
cylinders with liquefied compressed gases. Paragraph (d) of this
section provides for authorized containers for the filling of cylinders
with refrigerant and dispersant gases. Current regulations authorize
these gases in DOT 2Q non-refillable metal containers.
SP 12573 authorizes a refrigerant gas R 134a, (UN3159), in a non-
DOT specification container similar to a DOT 2Q container with a
maximum allowable pressure for the contents of 198 psig at 54.4 [deg]C
(130[emsp14][deg]F). In the NPRM, we differed marginally from the SP
and proposed to adopt a maximum pressure threshold of 200 psig at 55
[deg]C (131[emsp14][deg]F) for the container's contents. We indicated
there was no safety basis for the 200 psig ceiling other than we
believed it was a cleaner cutoff point than the 198 psig maximum found
in the SP. In addition, as part of the variation on the design of a DOT
2Q container, we proposed the modified container would be marked as a
``DOT 2Q1.''
Current regulations require that the pressure of the contents of
the metal containers not exceed 87 psig at 21 [deg]C
(70[emsp14][deg]F). In the NPRM, we invited comment on whether the
requirement for a maximum pressure should be specified at 21 [deg]C
(70[emsp14][deg]F) for the 2Q1 container in addition to the limit at 55
[deg]C (131[emsp14][deg]F). If so, we invited comment on what the upper
limit should be for a typical refrigerant or dispersant gas such as
1,1,1,2 Tetrafluoroethane, R134a.
In its comments, DSC suggests a single requirement of 210 psig at
55 [deg]C (131[emsp14][deg]F). It also suggests that such arbitrary
actions if adopted could increase the number of SP applications
submitted as a result. PHMSA recognizes the commenters concerns,
however, changing the reference temperature for the refrigerant gases
to 54.4 [deg]C (130[emsp14][deg]F) would make section 173.304(d)
inconsistent with the other sections for filling of gases. As noted in
the NPRM, PHMSA sought to have consistency where some sections referred
to 54.4 [deg]C (130[emsp14][deg]F) and some to 55 [deg]C
(131[emsp14][deg]F). In order to address the commenters concerns, PHMSA
is raising the proposed maximum pressure authorized in the new DOT 2Q1
container to 210 psig at 55[deg]C (131[emsp14][deg]F) as authorized in
Sec. Sec. 173.304 and 173.306. The burst pressure of the DOT 2Q1 will
have to be slightly raised accordingly to provide for the same safety
factor. This will be discussed in a later section. See the associated
discussion in the comments received from Dow earlier in this preamble.
Section 173.306
Section 173.306 prescribes the general requirements and exceptions
for limited quantities of compressed gases. In the NPRM, we proposed
numerous changes to this section. The proposed changes and resolutions
are discussed in the following.
Conforming Revisions
Throughout Sec. 173.306 of the HMR and within related SPs that
provide exemptions from these regulations for gases, pressure standards
are indicated at either 130[emsp14][deg]F or 131[emsp14][deg]F. In the
interest of consistency and conformity with the general requirements
for compressed gases in Sec. 173.301 and 173.301a, in the NPRM we
proposed to change all references of 54.4 [deg]C (130[emsp14][deg]F) to
55 [deg]C (131[emsp14][deg]F). We invited comment on whether there
would be any negative impacts in making this conforming change. We also
proposed making revisions to the construction and formatting of how
this section is presented (e.g., insertion of an ``if, then'' table) in
an effort to make the requirements more reader-friendly.
Authorized Metal Containers
DOT 2P Inner Nonrefillable Metal Containers
Under Sec. 173.306, limited quantities of foodstuffs or soaps with
soluble or emulsified compressed gas are authorized in nonrefillable
metal or plastic containers. The paragraph (b)(1) introductory text
authorizes these containers subject to a pressure not to exceed 140
psig at 54.4 [deg]C (130[emsp14][deg]F). SP 13601 and SP 14503
authorize the transportation of ``UN1950, Aerosols, non-flammable (each
not exceeding 1 L capacity), 2.2,'' and SP 7951 authorizes the
transportation of ``UN1956, Compressed gas, n.o.s., 2.2,'' in
containers that otherwise conform to DOT 2P or DOT 2Q specifications
with some modifications. Under the terms of SP 13601, the containers
must have a maximum pressure for the contents not to exceed 160 psig at
54.4 [deg]C (130[emsp14][deg]F) and, for SP 7951 and SP 14503, the
containers must have a maximum pressure for the contents not to exceed
150 psig at 23.9 [deg]C (75[emsp14][deg]F) and must be transported in a
refrigerated state.
In the NPRM, we requested comments on whether refrigeration should
be a condition of transport of these foodstuffs under pressure. In
their comments, DSC and CSPA both recommend that PHMSA continue to
require refrigeration as a condition of transport of these foodstuffs
under pressure. See the comment summary section for a more detailed
discussion of this issue. Because at least one of the special permits
to be incorporated (SP 13601) does not explicitly require
refrigeration, this requirement will not be adopted. Note that the
additional limit of 150 psig at 23.9 [deg]C (75[emsp14][deg]F) is
required. The shipper may use refrigeration if needed to achieve this
pressure. As part of the variation of the DOT 2P containers, the
modified containers are to be marked as ``DOT 2P1'' under the
provisions of new Sec. 178.33c discussed separately in this
rulemaking.
We also proposed in the NPRM to include the specification DOT 2P1
as an authorized metal aerosol container under Sec. 173.306(a)(3)(ii).
We saw no reason to limit the container to foodstuffs or soaps under
paragraph (b)(1) because the pressure limit for the contents is the
same as the current requirement for a standard DOT 2P container.
Lastly, we proposed that the DOT 2P1 would be authorized for both
Division 2.1 (flammable) and 2.2 (non-flammable) aerosols under
[[Page 3654]]
Sec. 173.306(a)(3)(ii). PHMSA received negative comments on the use of
the DOT 2P1 container for flammable gases. Because there has been no
experience with this type of container equipped with a pressure relief
device in flammable gas service, we will not adopt the 2P1 for any
materials other than those authorized in the special permits
incorporated at this time.
DOT 2Q Inner Nonrefillable Metal Containers
Under Sec. 173.306, limited quantities of compressed gas are
authorized in metal aerosol containers as defined in Sec. 171.8 of the
HMR. Paragraph (a)(3) introductory text of this section authorizes
metal aerosol containers under certain conditions to include packaging
types and pressure thresholds. Section 173.306(a)(3)(ii) currently
requires the use of a DOT 2Q container for pressures exceeding 160 psig
at 54.4 [deg]C (130[emsp14][deg]F) but not to exceed 180 psig. Except
for some modifications, SP 12573 authorizes the packaging of UN1950,
Aerosols, non-flammable, in non-DOT specification containers that
otherwise conform to the DOT 2Q specification with a maximum pressure
of 198 psig at 54.4 [deg]C (130[emsp14][deg]F).
In the NPRM, we proposed to adopt the modified DOT 2Q as an
authorized metal aerosol container. We differed marginally from the SP
in that we proposed to adopt a maximum pressure threshold of 200 psig
at 55 [deg]C (131[emsp14][deg]F). We stated that there was no safety
basis for the 200 psig ceiling other than we believed it was a cleaner
cutoff point than the 198 psig maximum found in the SP. Additionally,
we sought to provide consistency by using a reference temperature of 55
[deg]C (131[emsp14][deg]F). PHMSA received comments about the negative
impact of raising the reference temperature from 54.4 [deg]C
(130[emsp14][deg]F) to 55 [deg]C (131[emsp14][deg]F) particularly for
shippers of R134a which has a pressure of 198 psig at 54.4 [deg]C
(130[emsp14][deg]F). The commenters further stated that the pressure of
R134a at 55 [deg]C (131[emsp14][deg]F) is 202 psig and that a pressure
of 210 psig should be adopted. Consequently, in this final rule, PHMSA
will adopt a pressure of 210 psig at 55 [deg]C (131[emsp14][deg]F) in
order to allow for small variations; however, the reference temperature
will remain at 54.4 [deg]C (130[emsp14][deg]F). As part of the
variation of the specification of a DOT 2Q container, we stated the
modified container will be marked as ``DOT 2Q1.''
In the NPRM, the proposed design burst pressure of the DOT 2Q1 was
300 psig. Because the fill pressure of the DOT 2Q1 will be 210 psig at
55 [deg]C (131 [deg]F), PHMSA will raise the design burst pressure to
320 psig in this final rule. The pressure of 320 psig is consistent
with the minimum design burst pressure in SP 12573.
The NPRM also proposed to expand authorized materials to include
Division 2.1 aerosols for the DOT 2Q1 specification. At that time, we
saw no reason to limit the use of this container to non-flammable
aerosols based on its record of use and that DOT 2Q containers
currently authorized in the HMR are authorized to be used for all
aerosol types. We also invited comment on the suitability of the
container for all aerosol types. See the associated comment summary
discussions for Sec. Sec. 173.304 and 178.33d. PHMSA received mixed
comments on the use of the DOT 2Q1 container for flammable gases.
Because there has been no experience with this type of container
equipped with a pressure relief device in flammable gas service, we
will not adopt the DOT 2Q1 for any materials other than those
authorized in the special permits incorporated at this time.
SP 13581 is linked to the above proposed provision in that it
authorizes the use of metal aerosol containers manufactured, tested,
and marked according to SP 12573. We believe this SP will no longer be
needed with the adoption of the modified DOT 2Q container (i.e., a DOT
2Q1 container).
Alternatives to Testing of Metal Aerosol Containers by a Hot Water Bath
Test
As a condition of the use of a metal aerosol container used for
certain commodities, each container, after being filled, must be
subjected to a hot water bath to raise the internal pressure to such a
degree that leakage or permanent deformation, if any, can be determined
[see Sec. 173.306(a)(3)(v)]. The provision also provides for a testing
protocol for a container where the contents may be sensitive to heat.
Currently, this is the only method authorized for determining leakage
or permanent deformation. Thus, fillers that have developed other
testing protocols or do not want to subject their products to a hot
water bath test, must obtain a SP to do so. A number of SPs that
authorize the use of alternative methods to determine leakage or
permanent deformation are discussed as follows:
(1) Alternate hot water bath test. SP 12995 authorizes a
methodology that is a combination of a hot water bath test, a weight
test, and visual inspection. Rather than subjecting each filled
container to a hot water bath test, only one container out of each lot
is subjected to the hot water bath test, a second is subjected to a
weight test, the results of which must be compared to weight
specification for the container as outlined in quality control
procedures, and finally, the remainder of the lot must be visually
inspected by examining the valve, crimp, and seam areas for evidence of
leakage.
In the NPRM, we proposed to adopt SP 12995. The permit authorizes
only DOT 2Q containers but we are applying it to all authorized metal
aerosol containers. While determining if SP 12995 was suitable for
inclusion in this rulemaking, PHMSA's technical evaluators confirmed
that the methodology that includes a combination of hot water bath
test, weight test, and visual inspection may be performed on a DOT 2P
as well as a DOT 2Q. Since these containers are similar designs except
in terms of strength, this alternative to the hot water bath test is
applicable to any metal container. Previously, most applicants of SP
12995 only requested 2Q because that is what they needed for their
particular hazmat, but that does not mean that alternative testing is
not acceptable for similar containers. Additionally, the permit applies
to specific filling conditions but we will apply this testing method to
containers complying with the current filling conditions in Sec.
173.306(a)(3). Finally, we vary from the permit with our proposed
language in that we require maintenance and access to operating
procedures especially with regard to the weight test and specification
in order to effect a broader application of this alternative. Rather
than specify standards, we will allow persons to develop their own
procedures that best fit their product on the condition that DOT has
access to these procedures. Commenters were very supportive of our
proposals to adopt such testing alternatives and, in this final rule,
we are codifying them as proposed.
(2) Automated in-line pressure test. SPs 14429, 14623, 14625,
14627, 14723, 14724, 14786, 14842, 14887, 14953, 15135, 15265, 15427,
and 15972 all authorize the use of an automated process to check the
pressure of filled containers (i.e., an ``automated in-line pressure
check'') instead of subjecting the containers to a hot water bath. In
this final rule, we are adopting the provisions of these SPs as
proposed that authorize the use of an automated process for pressure
checks that does not involve a hot water bath.
(3) Weight test. SP 14440 authorizes the use of a process to check
the weight of filled containers (i.e., an ``automated in-line pressure
check'') instead of subjecting the containers to a hot water bath. In
this final rule, we are adopting the provisions of the SP as proposed
to
[[Page 3655]]
authorize the use of weight checks as a means to determine compliance
with pressure requirements.
(4) Leakage test. SP 14544 authorizes the use of a high pressure
air test on empty containers combined with a leakage test for filled
containers instead of subjecting the containers to a hot water bath.
The testing protocol for filled containers found in this SP is
currently applied to plastic containers under paragraph (a)(5) of this
section in the HMR, however, the pressure and leakage test of the empty
containers differs in its application. Under SP 14544, each empty
container must be pressure tested at 120 psig instead of the HMR
requirement that each empty container must be subjected to a pressure
equal to or in excess of the maximum expected in the filled containers
at 55 [deg]C (131 [deg]F), and that is at least two-thirds of the
design pressure of the container. Under both tests, if there is
evidence of leakage, the container must be rejected. In this final
rule, we are adopting the provisions of the SP as proposed to authorize
the use of a leakage test as a means to determine compliance with
pressure requirements. Our implementation differs from the SP in that
we are adopting the leakage testing requirements under Sec.
173.306(a)(5)(v), but including the SP 14544 testing protocol for empty
containers as an alternative.
Accumulators
The HMR provide special considerations for compressed gases in
accumulators. SP 8786 authorizes the transport of accumulators under an
alternative testing procedure than what is prescribed in paragraphs
(f)(2) and (f)(3) of this section. Rather than testing each accumulator
to three times (3x) the charge pressure, the SP provides for conditions
to test one accumulator out of each lot of 1,000 to the burst design
pressure, and two accumulators to two and a half times (2.5x) the
charge pressure. In the NPRM, we proposed to adopt most of SP 8786 into
Sec. 173.306. Because we did not receive public comment on this
amendment, supportive or otherwise, it is adopted as proposed in the
NPRM.
Aerosol Disposal
The general packaging requirements of the HMR forbid the transport
of leaking or improperly-filled packages. This includes aerosol
containers that are found to be leaking or improperly filled as part of
a combination packaging. SP 11296 provides an option to transport these
containers to an offsite facility for disposal under certain conditions
(e.g., overpacking in DOT specification packagings, modal restrictions,
etc.). In the NPRM, we proposed to adopt the general scope of SP 11296
with some differences. We proposed to also permit non-flammable
aerosols. Further, the proposed regulatory language was modeled after
the salvage packaging requirements of Sec. 173.3(c) in that: (1) The
authorized outer packaging for overpacking the defective cylinders has
been expanded to include other metal drums (i.e., 1B2 and 1N2); (2) a
condition for cushioning and absorbent material, when necessary, has
been added; and (3) an ``aerosol salvage'' drum marking has been
adopted. Commenters were very supportive of our proposals to adopt such
provisions for aerosol disposal and, in this final rule, we are
codifying them as proposed.
Part 178
Section 178.33c
Under the HMR, certain DOT specification containers with restricted
capacity and commonly referred to as ``aerosol containers'' are
authorized for the transportation of compressed and liquefied
compressed gases under certain scenarios. These containers include DOT
2P (inner non-refillable metal) containers. The specification standards
are prescribed in Sec. 178.33 of the HMR and do not provide for
variations of those standards. Thus, technological advances or design
modifications to satisfy customer needs are such that the resulting
metal containers would not conform to the standards for a DOT 2P
container, nor any other container authorized under Sec. Sec. 173.304
or 173.306 of the HMR. SPs 13601 and 14503 (also 7951) provide for a
variation of the DOT 2P container specifications by authorizing
construction of the container according to modifications of the
standards for manufacture and testing.
The special permits authorized variations of a DOT 2P container
that are equipped with some manner of pressure relief system (e.g., a
rim-vent release device or a dome expansion device). The rim vent
release devices must function within a certain pressure range,
otherwise the container is rejected. The dome expansion devices are
designed to buckle to relieve pressure before bursting. For example,
for a container built to SP 13601, the pressure relief system must
function between 175 psig and 210 psig or be rejected.
In the NPRM, we stated that we have no specific information in the
SP(s) on the relationship between the functional range and the tested
burst pressure. The current minimum burst pressure for a DOT 2P
container is 240 psig (Sec. 178.33-8). Using the SP 13601 construction
requirements, the minimum burst pressure is indicated as 270 psig
(assumed at 130 [deg]F) and pressure of the contents at 130 [deg]F may
not exceed 160 psig thus, equating to approximately 1.7x the contents
at 130 [deg]F without bursting (which is more stringent than for a DOT
2P under the HMR). Thus, the upper pressure range of the relief system
is 77.8% of the design burst pressure of 270 psig.
This is further complicated under SP 14503 (and 7951) where the
standard for the pressure of the contents is set at 23.9 [deg]C (75
[deg]F) for which we do not have an equivalent requirement under the
HMR. Additionally, the ranges for functioning of the relief systems
have a higher upper bound, 175 psig to 250 psig and 175 psig to 235
psig, respectively. Lastly, there is no minimum burst pressure
specified in SP 14503 (and 7951); therefore, we must default to the DOT
2P minimum burst pressure of 240 psig. Again, the circumstances are
unclear in that the upper bounds for the functional ranges approach or
exceed the DOT 2P minimum burst pressure yet we do not have information
on the actual tested burst pressure which could be much larger.
Therefore, based on the requirements of SP 13601, we proposed to
implement a requirement that for containers with pressure relief
systems, the upper bound of the functional range for a pressure relief
system must be no greater than 85% of the minimum burst pressure. In
the NPRM, we proposed to incorporate the standards for the modified DOT
2P container described in SP 13601 (and likely 14503 (7951)) as a
variation of the DOT 2P container design. As adopted in this final
rule, the variation is required to be marked as a ``DOT 2P1.'' All
standards for a DOT 2P1 remain the same as those for a DOT 2P except
for the variations prescribed in new Sec. 178.33c-2.
Commenters expressed concerns about imposing pressure limits on the
range of the pressure relief systems although there are various
pressure limits in each special permit that incorporates a rim vent
release type of device in the container design. The commenters state
that the actual activation range of the pressure relief system design
is not as important to safety as that the system must function before
the container bursts. We agree with the commenters. In the testing
requirement of DOT 2P1, the performance standard is that the containers
must fail at the location of the pressure relief system or the lot will
be rejected. PHMSA believes that incorporating the DOT 2P1 without a
[[Page 3656]]
specific functional range or limit for a rim vent release system will
make the container specification more suitable for incorporation into
the HMR because of broader applications rather than prescriptive
regulatory text based on specific special permits. In this final rule,
PHMSA will incorporate the requirements for the end expansion devices
as proposed. The containers with an end expansion device must buckle
prior to burst.
Section 178.33d
Under the HMR, certain DOT specification containers with restricted
capacity and commonly referred to as ``aerosol containers'' are
authorized for the transportation of compressed and liquefied
compressed gases under certain scenarios. These containers include DOT
2Q (inner non-refillable metal) containers. Though the DOT 2Q
specification is prescribed in Sec. 178.33a of the HMR, it does not
provide for variations of those standards. Thus, technological advances
or design changes to satisfy customer needs are such that the resulting
metal containers would not conform to the standards of a DOT 2Q
container, nor any other container authorized under either Sec. Sec.
173.304 or 173.306 of the HMR. SP 12573 provides for a variation of the
DOT 2Q container specifications by authorizing construction of the
container according to modifications to the standards for type and
size, manufacture, wall thickness, and testing. SP 14503 also provides
for a variation of the DOT 2Q container specification by authorizing
construction of the container according to modifications to its
manufacture and testing criteria.
Variations provided in the SPs for DOT 2Q containers require that
they are equipped with some type of pressure relief system (e.g., a
rim-vent release device or a dome expansion device), that must function
by a certain threshold level or within a certain pressure range,
otherwise the container is rejected. In effect, these containers are
designed to buckle to relieve pressure before bursting. For example,
for a container built to SP 12573, the minimum pressure before the
system buckles is 220 psig (and if not equipped with a pressure relief
system, the container may not burst below 320 psig). The maximum
pressure of the contents authorized under this SP is 198 psig at 54.4
[deg]C (130 [deg]F) (in the NPRM, we proposed a maximum pressure of 200
psig based on this SP in the Sec. 173.306 discussion for DOT 2Q
containers). After reviewing comments to the NPRM, we will adopt a
maximum pressure of 210 psig at 55 [deg]C (131 [deg]F) in this final
rule. The current requirements for a DOT 2Q container under Sec.
173.306(a)(3)(ii) is that the pressure of the contents cannot exceed
180 psig at 54.4 [deg]C (130 [deg]F) and the container must be capable
of withstanding a pressure of 1.5x the contents at 54.4 [deg]C (130
[deg]F) without bursting. Applying the same multiplier to 210 psig, the
container must withstand at least 305 psig without bursting. The SP
12573 minimum burst pressure of 320 psig is more than the current
required minimum burst pressure of 270 psig for a DOT 2Q container;
however, it provides approximately the same safety factor of 1.52. In
this final rule, we are adopting as proposed the standards for the
modified DOT 2Q container found in SP 12573 as a variation of the DOT
2Q container design. This variation is required to be marked ``DOT
2Q1.''
The requirements under SP 14503 operate differently in that the
standard for the pressure of the contents is set at 23.9 [deg]C (75
[deg]F) to which we do not have an equivalent requirement under the
HMR. Additionally, the SP provides for a range of pressure for
functioning of the relief systems, specifically, 180 to 300 psig.
Lastly, there is no minimum burst pressure specified in SP 14503 so we
must default to the DOT 2Q minimum burst pressure of 270 psig. The
upper bound for the functional range exceeds the 2Q minimum burst
pressure yet we do not have information on the actual tested burst
pressure which could be much larger. Therefore, based on a similar
proposal to implement provisions of SP 13601 for 2P containers (see
Sec. 178.33c preamble discussion), the upper bound of the functional
range for a pressure relief system must be no greater than 80% of the
test pressure. In the NPRM, we invited comment on using this approach
and whether it would be preferable to implement a requirement for the
upper bound of the range based on the pressure of the contents.
Commenters did not respond specifically to the question of
functional range for the DOT 2Q1 or 2Q2; however, they expressed
concerns about imposing pressure limits on the range of the pressure
relief systems of the DOT 2P1 which incorporates a similar pressure
relief system design. The commenters state that the actual activation
range of the pressure relief system design is not as important to
safety as that the system must function before the container bursts. We
agree with the commenter. We are imposing the same testing requirement
as that for the DOT 2P1 in that the containers must fail at the
location of the pressure relief system or the lot will be rejected. The
containers with an end expansion device must buckle prior to burst.
In this final rule, we are adopting as proposed the standards for
the modified DOT 2Q container described in SP 14503 as a variation on
the DOT 2Q container design. This variation is required to be marked as
a ``DOT 2Q2.'' Further, the pressure relief device requirements for the
DOT 2Q2 will be the same as that for the DOT 2P1 and 2Q1.
C. Cargo Tanks/Rail Cars/Portable Tanks
Part 173
Section 173.315
Section 173.315 prescribes bulk packaging provisions for liquefied
compressed gases in UN and DOT specification cargo tanks and portable
tanks.
SP 12576 authorizes non-DOT specification cargo tanks for the
transportation of ``UN1080, Sulfur hexafluoride'' that otherwise
conform to the MC 331 specifications except for design pressure,
capacity, and marking. In the NPRM, we proposed to revise the Sec.
173.315(a)(2) table by referring to a new note 28 in the entry for
``Division 2.2, materials not specifically provided for in this table''
as Sulfur hexafluoride is not listed by name in the table. New note 28
codifies such tanks specified in SP 12576 for the transportation of
sulfur hexafluoride. Because we did not receive public comment on this
amendment, supportive or otherwise, it is adopted as proposed in the
NPRM.
Section 173.319
Section 173.319 prescribes the loading and packaging provisions for
cryogenic liquids transported in rail tank cars.
SP 12039 authorizes the transportation in commerce of DOT 113C120W
rail tank cars containing ``UN1038, Ethylene, refrigerated liquid,'' at
an internal pressure of 20 psig instead of the maximum 10 psig.
Currently, the HMR authorizes a maximum of 10 psig in a DOT 113C120W
rail tank car containing cryogenic ethylene when offered for
transportation by rail. Because we did not receive public comment on
this amendment, supportive or otherwise, it is adopted as proposed in
the NPRM.
D. Operational Air/Vessel
Part 176
Section 176.90
Section 176.90 prescribes requirements for private automobiles
[[Page 3657]]
carrying Class 1 hazardous materials on board ferry vessels. There are
four SPs that provide relief for ferry transport of private automobiles
carrying engines, gasoline, and propane. SP 7465, 11150, 13213, and
14458 all contain slightly different provisions to facilitate this
process safely. Where differences exist between these permits, PHMSA
has attempted to choose the least restrictive provision for adoption.
In the NPRM, PHMSA proposed to renumber the existing paragraph in
Sec. 176.90 as paragraph (a), and add a new paragraph (b) to adopt an
exception for ``UN3166, Engines, internal combustion, flammable gas
powered or flammable liquid powered, including when fitted in machinery
or vehicles (i.e. motor vehicles, recreational vehicles, campers,
trailers), vehicle flammable liquid or flammable gas powered, gasoline,
and petroleum gases, liquefied or liquefied petroleum gas'' when
included as part of a motor home, recreational vehicle, camper, or
trailer and carried aboard ferry vessels subject to certain operational
controls. Because we did not receive public comment on this amendment,
supportive or otherwise, it is adopted as proposed in the NPRM.
Section 176.800
Section 176.800 of the HMR prescribes general vessel stowage
requirements for corrosive materials.
SP 11691 authorizes transportation in commerce of certain flammable
and corrosive liquids, which are the ingredients of soft drinks
(beverages), not subject to the segregation requirements for vessel
stowage when shipped in the same transport unit. In the NPRM, we
proposed to add a new special provision, W11, to Sec. 172.102,
regarding vessel segregation of corrosive and combustible materials and
foodstuffs. Based on comments from PCSD, proposed Special provision W11
is being replaced by revising paragraph (a) of Sec. 176.800 to allow
Class 8 (corrosive) materials that are also foodstuffs or foodstuff
ingredients intended for human consumption to not be considered
incompatible for segregation purposes.
E. Operational Highway/Rail/Shipper/Other
Part 171
Section 171.8
Section 171.8 defines terms generally used throughout the HMR that
have broad or multi-modal applicability.
In the NPRM, PHMSA proposed to add the following definition based
on the adoption of SP 11458:
Display pack means a package intended to be placed at retail
locations which provide direct customer access to consumer commodities
contained within the package when all or part of the outer fiberboard
packaging is removed.
SP 11458 authorizes the transportation in commerce of display packs
of consumer commodity packages or limited quantity packages that exceed
the 30 kg gross weight limit. The provisions of SP 11458 were proposed
for adoption into Sec. 173.156. However, the term ``display pack'' is
not currently defined in the HMR. In the NPRM we proposed to adopt the
definition of ``display pack'' in Sec. 171.8 based upon its definition
in SP 11458. Commenters were very supportive of our proposal to adopt a
definition of display packs in Sec. 171.8 and, in this final rule, we
are codifying it as proposed.
Part 172
Sections 172.101 (Hazardous Materials Table) and 172.102 Special
Provisions
Section 172.101 provides instructions for using the Hazardous
Materials Table (HMT) and the HMT itself. Column 7 of the HMT provides
codes for special provisions applicable to specific hazardous materials
descriptions. Special provisions may contain unique packaging
requirements, prohibitions, and exceptions applicable to particular
quantities or forms of hazardous materials. When Column 7 of the HMT
refers to a special provision, the requirements of that special
provision are as set forth in Sec. 172.102. In the NPRM, PHMSA
proposed the following revisions to Sec. 172.102:
Special Provision 380
SP 10705 provides relief from the segregation requirements of Sec.
177.848(d) for the transport of ``UN1092, Acrolein, stabilized,'' by
private carrier in a motor vehicle. In the NPRM, PHMSA proposed to add
Special Provision 380 to Sec. 172.102(c)(1) to codify SP 10705. The SP
prescribes the packaging that must be used and the materials in which
it may be loaded. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed.
Special Provision 381
SP 7991 provides relief from the HMR for the transportation of
railroad flagging kits by highway. See Sec. 173.184 for a detailed
discussion of the adoption of SP 7991. In the NPRM, PHMSA proposed to
add Special Provision 381 to Sec. 172.102(c)(1) to codify SP 7991. As
adopted in this final rule, Special Provision 381 will be assigned to
the following HMT entries: Fusee (rail or highway) (NA1325, Division
4.1, PG II); Articles, pyrotechnic (UN0431, Division 1.4G, PG II);
Signal Devices, hand (UN0373, Division 1.4S, PG II); Signal Devices,
hand (UN0191, Division 1.4G, PG II); and Signals, railway track,
explosive (UN0193, Division 1.4S, PG II). Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
Special Provision 382
SP 8006 provides relief from the labeling requirements of Sec.
172.400(a) for the transportation of toy plastic or paper caps for toy
pistols by motor vehicle, railcar, cargo vessel, and cargo aircraft.
See Sec. 172.400a(a)(8) for a detailed discussion of the adoption of
SP 8006. In the NPRM, PHMSA proposed to add Special Provision 382 to
Sec. 172.102(c)(1) to codify SP 8006. Special Provision 382 will be
assigned to the following HMT entries: Articles, explosive, n.o.s.
(UN0349) and Toy caps (NA0337). Because we did not receive public
comment on the proposal, adverse or otherwise, in this final rule, we
are adopting the amendment as proposed.
Special Provision 383
SP 11356 authorizes material meeting the conditions for high
viscosity flammable liquids specified in Sec. 173.121(b)(1)(i),
(b)(1)(ii), and (b)(1)(iv), to be re-classed to Packing Group III for
transportation by motor vehicle. In the NPRM, PHMSA proposed to add
Special Provision 383 to Sec. 172.102(c)(1) to codify SP 11356. The SP
prescribes packaging, capacity limitations, and load securement
requirements. Special Provision 383 will be assigned to the following
HMT entries: Coating solution (UN1139, PG II) and Paint (and Paint
related material) (UN1263, PG II). Because we did not receive public
comment on the proposal, adverse or otherwise, in this final rule, we
are adopting the amendment as proposed.
Special Provision 384
SP 11666 authorizes the transportation of green graphite electrodes
and shapes that are large single component solid objects not subject to
sifting, in open rail flat cars, open bed motor vehicles, and
intermodal containers. In the NPRM, PHMSA proposed to add Special
Provision 384 to Sec. 172.102(c)(1) to codify SP 11666. The SP
prescribes load securement requirements for the electrodes and shapes.
Further, the SP permits stacking two or more levels high
[[Page 3658]]
to achieve maximum allowable utilization of the designated vehicle,
rail car weight, or intermodal freight container weight or vessel hold
volume. Special Provision 384 will be assigned to the following HMT
entries: Other regulated substances, n.o.s. (NA3077, PG III) and
Environmentally hazardous substances, solid, n.o.s. (UN3077, PG III).
In this final rule, we are adopting the amendments as proposed with
minor editorial clarifications.
Special Provision 385
SP 13343 authorizes the use of cargo heaters when weather
conditions are such that the freezing of certain wetted explosive
material is likely. In the NPRM, PHMSA proposed to add Special
Provision 385 to Sec. 172.102(c)(1) to codify SP 13343. Transportation
must be performed by private, leased or contract carrier vehicles in
exclusive use. Further, cargo heaters must be reverse refrigeration
(heat pump) units. Shipments made in accordance with the SP are
excepted from the anti-freeze requirements of Sec. 173.60(b)(4). The
provisions of SP 13343 are specific to ``UN0394, Trinitroresorcinol,
wetted or Styphnic acid, wetted with not less than 20% water, or
mixture of alcohol and water by mass''; therefore, Special Provision
385 will be assigned exclusively to those HMT entries. Because we did
not receive public comment on the proposal, adverse or otherwise, in
this final rule, we are adopting the amendment as proposed.
Special Provision 386
In the NPRM, we proposed to codify SP 6614 by establishing a new
paragraph (b)(3) to authorize polyethylene bottles with rated
capacities of one gallon (3.785 liters), packed inside an open-top,
heavy wall, high density polyethylene box for shipping certain PG II
and III corrosive liquids by private motor carrier. In this final rule,
we are adopting SP 6614 as proposed; however, we are moving the
amendment from paragraph (b) to new Sec. 172.102(c)(1), Special
provision 386, as it is a more appropriate location in the HMR for it.
Special Provision B130
SP 14525 provides relief from the HMR except for the shipping paper
requirements of Subpart C of Part 172, emergency response information
as required by Sec. 172.602, and the marking requirements of Sec.
172.302(a), (b), and (d) when transporting used diatomaceous earth
filter material by highway. In the NPRM, PHMSA proposed to add Special
Provision B130 to Sec. 172.102(c)(3) to codify SP 14525. The SP
prescribes packaging, quantity limitations, and the required method of
storing the packages within the motor vehicle. The provisions of SP
14525 are specific to ``UN3088, Self-heating solid, organic, n.o.s''
(PG III); therefore, Special Provision B130 will be assigned
exclusively to that HMT entry. Because we received minimal public
comment on the proposal, in this final rule, we are adopting the
amendment as proposed.
Special Provision B131
As previously discussed, SP 11624 was not proposed for adoption in
the NPRM. The SP is in its fifteenth revision and has 114 grantees. The
SP authorizes transportation in commerce of certain waste Class 3 paint
and paint related material (UN1263; PG II and PG III) contained in
metal or plastic pails further packed in non-specification bulk
packagings such as cubic yard boxes, plastic rigid-wall bulk
containers, dump trailers, and roll-off containers. After careful
reevaluation, SP 11624 and three related packaging SPs (i.e., SP 13052,
SP 14712, and 15235) are adopted as new Sec. 172.102(c)(3), Special
Provision B131.
Special Provision B132
SP 11602 authorizes the transportation in commerce of certain
Division 4.3 materials contained in sift-proof closed bulk packagings
that prevent water from reaching the hazmat and have sufficient venting
to preclude a dangerous accumulation of gaseous emissions. In the NPRM,
we proposed to adopt the provisions of SP 11602 in its entirety in
Sec. 173.151(g). Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed. However, in this final rule, we are moving the
amendment to new Sec. 172.102(c)(3), Special provision B132 as it is a
more appropriate section for these provisions.
Section 172.202
Section 172.202 prescribes requirements for describing hazardous
materials on shipping papers. In many scenarios, a net or gross
quantity of the hazardous materials must be included.
SP 11811 provides relief from this requirement for local
collections operations transporting hazardous materials and hazardous
substances by highway that are ``household wastes'' as defined in 40
CFR 261.4 and not subject to the Environmental Protection Agency's
hazardous waste regulations in 40 CFR, Parts 262 and 263. In the NPRM,
we proposed to revise paragraph (c) of Sec. 172.202 to adopt the
provisions of SP 11811 in its entirety. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
Section 172.315
Section 172.315 prescribes marking requirements for packages of
limited quantities of hazardous materials.
SP 11197 provides relief from the requirement to display the
limited quantity marking on packages containing certain low-risk
materials assigned to PG II and III prepared in accordance with the
limited quantity provisions in Subpart B of part 173 of the HMR for
highway transportation by private motor carrier. The SP prescribes
inner packaging and package quantity limitations; the maximum gross
weight of packages that may be transported in one vehicle; and special
package marking requirements. In the NPRM, we proposed to add a new
paragraph (a)(3) to Sec. 172.315 to adopt the provisions of SP 11197
in its entirety. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed.
Section 172.400a
Section 172.400a provides exceptions from the Sec. 172.400 general
labeling requirements for packages or containment devices of hazardous
materials.
SP 8006 provides relief from the Sec. 172.400 general labeling
requirements for toy plastic or paper caps for toy pistols described as
``UN0349, Articles, explosive, n.o.s. (Toy caps), 1.4S'' or ``NA0337,
Toy caps, 1.4S'' when offered for transportation by motor vehicle, rail
freight, cargo vessel, and cargo aircraft. The toy plastic or paper
caps must have been examined in conformance with Sec. 173.56 and
approved by the Associate Administrator. In the NPRM, we proposed to
add a new paragraph (a)(8) to Sec. 172.400a to adopt the provisions of
SP 8006 in its entirety. Because we did not receive public comment on
the proposal, adverse or otherwise, in this final rule, we are adopting
the amendment as proposed.
Part 173
Section 173.12
Section 173.12 provides certain exceptions and authorizations for
the transportation of waste hazardous materials.
SP 11470 authorizes transportation by motor vehicle and cargo
vessel of shrink-wrapped pallets containing boxes of waste ORM-D or
limited quantity materials when marked with the word ``WASTE'' on the
outside of
[[Page 3659]]
the pallet instead of each individual box. The SP also prescribes
packaging requirements for the waste materials. COSTHA requested that
PHMSA adopt this SP into the HMR under petition for rulemaking P-1611.
In the NPRM, we proposed to add a new paragraph (h) to Sec. 173.12 to
adopt the provisions of SP 11470 in its entirety. Because of the
supportive public comments received as a result of our proposal, in
this final rule, we are adopting the amendments as revised. Based on
comments from Veolia, the revisions include authorizing ``stretch-
wrapped'' pallets in addition to shrink-wrapped pallets and
``packages'' rather than boxes only.
Section 173.29
Section 173.29 prescribes certain requirements, exceptions, and
authorizations for the transportation of empty packagings.
SP 9610 provides relief from shipping paper and placarding
requirements of Subparts C and F of part 172, respectively, for
smokeless powder residue when transported by motor vehicle or railcar
in ``Container-on-flat-car'' (COFC) or ``Trailer-on-flat-car'' (TOFC)
service. The smokeless powder must be approved in conformance with
Sec. 173.56 as a Class 1 explosive substance. The SP prescribes
packaging requirements, quantity limitations, operational controls, and
a specific shipping description for the material. In the NPRM, we
proposed to revise paragraph (f) of Sec. 173.29 to adopt the
provisions of SP 9610 in its entirety. Because of the supportive public
comments received as a result of our proposal, in this final rule, we
are adopting the amendments as proposed with minor revisions to allow
additional packaging types.
Section 173.63
Section 173.63 provides packaging exceptions for certain Class 1
(explosive) materials.
SP 4850 authorizes Cord, detonating, or Fuse detonating, metal clad
(UN0290, Div. 1.1D) to be renamed and reclassed as Cord, detonating,
mild effect, or Fuse, detonating, mild effect, metal clad (UN0104, Div.
1.4D); and Charges, shaped, flexible, linear (UN0288, Div. 1.1D) to be
renamed and reclassed Charges, shaped, flexible, linear (UN0237, Div.
1.4D) and transported by motor vehicle, railcar, cargo vessel, and
cargo aircraft. The SP prescribes packaging requirements and quantity
limitations. In the NPRM, we proposed to revise paragraph (a) of Sec.
173.63 to adopt the provisions of SP 4850 in its entirety. However,
during review of the final rule, concerns that there was insufficient
hazard communication to prevent the reclassed shipments from finding
their way into the air mode were raised. In addition, concerns
regarding the distinctions between shipping being offered domestically
versus internationally were discussed. Because additional conditions
for its adoption were not proposed in the January 30, 2015 NPRM, in
this final rule, we are not codifying SP 4850 into the HMR at this time
but intend to consider it for incorporation in the near future
considering the hazard communication concerns. We will include any
proposals in upcoming NPRMs for comment.
Section 173.156
Section 173.156 provides exceptions for the transportation of
certain limited quantities and other regulated materials (ORM).
SP 11458 authorizes display packs of consumer commodity packages
that exceed 30 kg gross weight for transportation by railcar in
trailer-on-flat-car (TOFC) or container-on-flat-car (COFC) service, or
roadrailer and/or railrunner trailers or by motor vehicle, or cargo
vessel. See Sec. 171.8 for a discussion of the addition of the
definition of display pack. In a petition for rulemaking (P-1607),
COSTHA requested PHMSA adopt this SP into the HMR. In the NPRM, we
proposed to add a new paragraph (c) to Sec. 173.156 to adopt the
provisions of SP 11458 in its entirety. Because of the supportive
public comments received as a result of our proposal, in this final
rule, we are adopting the amendment as proposed.
SP 11470 authorizes transportation by motor vehicle and cargo
vessel of shrink-wrapped pallets containing boxes of waste ORM-D or
limited quantity materials when marked with the word ``WASTE'' on the
outside of the pallet instead of each individual box. The adoption of
SP 11470 relating to exceptions for waste limited quantity and ORM-D
materials is discussed in the preamble for Sec. 173.12. In the NPRM,
we proposed to add a new paragraph (d) to Sec. 173.156 that directs
the reader to the new paragraph (h) of Sec. 173.12 which codifies the
provisions of SP 11470. Because of the supportive public comments
received as a result of our proposal, in this final rule, we are
adopting the amendment as proposed with one modification. Veolia
supports adoption of SP 11470 with one substantial modification--the
HMR should not limit to ``expired'' consumer products but rather all
consumer commodities shipped for disposal/recycling under manufacturer
recalls, off-spec/unwanted/unneeded product, etc. We recognized the
merit of Veolia's comment and revised Sec. 173.12 accordingly.
Section 173.159
Section 173.159 prescribes requirements for the transportation of
wet electric storage batteries.
SP 11078 conditionally excepts the transportation of nickel cadmium
batteries containing potassium hydroxide, a Class 8 material, from
other requirements of the HMR when transported by motor vehicle,
railcar, cargo vessel and passenger and cargo aircraft. In the NPRM, we
proposed to add a new paragraph (j) to Sec. 173.159 to codify the
provisions of SP 11078 in its entirety. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
SP 13548 authorizes transportation in commerce of lead acid
batteries and packages of battery acid (with two different
identification numbers) on the same vehicle. Commenters were supportive
of its adoption in the HMR. In this final rule, the introductory text
in paragraph (e) is revised accordingly.
Section 173.168
Section 173.168 prescribes specific approval, testing, protection,
packaging, and equipment marking requirements for chemical oxygen
generators.
SP 11984 authorizes certain unapproved chemical oxygen generators
with only one positive means of preventing unintentional actuation of
the generator, and without the required approval number marked on the
outside of the package, to be transported by motor vehicle, railcar,
and cargo vessel. In the NPRM, we proposed to add a new paragraph (g)
to Sec. 173.168 to adopt the provisions of SP 11984 in its entirety.
Veolia supports adoption of SP 11984 with one modification--the HMR
should require flame-proof outer packaging for chemical oxygen
generators shipped with only one positive means of preventing
unintentional activation as expressed in concern for equivalent level
of safety in proposed SP modification in August 2011. Veolia's comments
notwithstanding, because of the mainly supportive public comment
received and safety evaluation as a result of our proposal, in this
final rule, we are adopting the amendment as proposed.
Section 173.184
Section 173.184 prescribes packaging requirements for the
transportation of highway or rail fusees.
[[Page 3660]]
When in conformance with SP 7991, flagging kits transported on
railroad motor vehicles including privately-owned motor vehicles under
the direct control of on-duty railroad employees, are excepted from the
requirements of the HMR. Flagging kits may only contain fusees and
railroad torpedoes described as: Fusee (rail or highway) (NA1325,
Division 4.1, PG II); Articles, pyrotechnic (UN0431, Division 1.4G, PG
II); Signal devices, hand (UN0373, Division 1.4S, PG II); Signal
devices, hand (UN0191, Division 1.4G, PG II); and Signals, railway
track, explosive (UN0193, Division 1.4S, PG II). This SP prescribes
packaging requirements, quantity limitations, and operational controls.
In the NPRM, we proposed to add a new paragraph (c) to Sec. 173.184 to
adopt the provisions of SP 7991 in its entirety. Because we did not
receive public comment on the proposal, adverse or otherwise, in this
final rule, we are adopting the amendment as proposed.
Section 173.226
Section 173.226 prescribes specific packaging requirements for the
transportation of materials poisonous by inhalation, Division 6.1, PG
I, Hazard Zone A.
When transported as prescribed in SP 11055, liquid hazardous
materials in Division 6.1, PG I, Hazard Zone A, are excepted from the
segregation requirements of Sec. Sec. 174.81, 176.83, and 177.848(d).
The SP prescribes packaging and testing requirements, quantity
limitations, and cushioning and absorbent material requirements. In the
NPRM, we proposed to add a new paragraph (f) to Sec. 173.226 to adopt
the provisions of SP 11055 in its entirety. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
Section 173.306
Section 173.306 provides exceptions for limited quantities of
compressed gas. Section 173.306(e) currently permits only new (unused)
refrigerating machines to be excepted from specification packaging,
placarding, and certain rail and highway modal requirements.
SP 13199 permits reconditioned (used) refrigerating machines
(UN2857, Div. 2.2) to be transported under the requirements prescribed
in Sec. 173.306(e) and excepted from the marking requirements of Sec.
172.302(c) when transported by motor vehicle and meeting certain
structure and Class A refrigerant gas weight requirements. In the NPRM,
we proposed to add new paragraph (e)(2) to Sec. 173.306 to adopt the
provisions of SP 13199 in its entirety. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
Section 173.322
Section 173.322 prescribes packaging requirements for ethyl
chloride. In the January 30, 2015 NPRM, we proposed to add a new
paragraph (f) to Sec. 173.322 to adopt the provisions of SP 14422 in
its entirety. Because SP 14422 is no longer an active special permit,
in this final rule, we are not adopting the amendment as proposed.
Part 174
Section 174.67
Section 174.67 prescribes operational requirements for the railroad
tank car unloading of hazardous materials.
SP 12002 authorizes the clearing of frozen liquid blockages from
tank car outlets by attaching a fitting to the outlet line and applying
nitrogen at a pressure of 50 to 100 psi for combustible liquid or Class
3 liquid petroleum distillate fuels. In the NPRM, we proposed to revise
paragraph (g) to Sec. 174.67 to adopt the provisions of SP 12002 in
its entirety. In its comments, ACA recommends that the use of nitrogen
should be permitted ``at a pressure of up to 100 psi'' for clarity. We
agree and revise Sec. 174.67(g) accordingly.
Part 177
Section 177.820
Currently there is no Sec. 177.820 in the HMR. However, in the
NPRM, we proposed to add a new Sec. 177.820 that authorizes the
movement of certain hazardous materials across public roads with
limited exceptions.
SPs 11352, 12207, 12306, 13165, and 14945 authorize the movement of
certain hazardous materials across public roads. Such movements are not
subject to Subparts C (Shipping Papers), D (Marking), E (Labeling), and
F (Placarding) of Part 172. The SPs prescribe specific operational
controls. In the NPRM, we proposed to add a new Sec. 177.820 to adopt
the provisions of these SPs in their entirety. COSTHA and DGAC support
the adoption of SPs 11352, 12207, 12306, 13165, and 14945; however,
according to COSTHA, the proposed regulatory text in Sec. 177.820
appears to be more restrictive than the HMR applicability exceptions
currently in Sec. 171.1(d)(4). We agree with COSTHA and are not
adopting the five SPs and new Section 177.820 as proposed in the NPRM.
Section 177.834
Section 177.834 establishes general operational requirements for
hazardous materials transportation by highway.
SPs 9874, 13190, 13424, 13959, 14141, 14150, 14680, 14822, 14827,
and 14840 authorize ``attendance'' of the loading or unloading of a
cargo tank by a qualified person observing all loading or unloading
operations by means of video cameras and monitors or instrumentation
and signaling systems such as sensors, alarms, and electronic
surveillance equipment located at a remote control station. In the
NPRM, we proposed to revise paragraphs (i)(3) and (i)(4) of Sec.
177.834 to adopt the provisions of these SPs in their entirety.
In its comments, Dow supports codification of the SPs but has
specific concerns: (1) SP 9874 and 14822 authorize instrumentation and
signaling systems such as sensors, alarms, and electronic surveillance
equipment in addition to video monitoring; (2) SPs 9874 and 14822 do
not require a video camera with a ``motorized zoom lens capable of
panning and zooming from the remote control station''; (3) SPs 9874 and
14822 do not require that the view capability must include the entire
containment area; and (4) the need for assurance that the attendance
requirements in Sec. 177.834 (i) apply to motor carriers only. We
agree that Dow's comments have merit and, in this final rule, except
for number (4), the regulatory text in Sec. 177.834(i) is revised
accordingly. Regarding issue number (4), long-standing interpretations
preclude the need to revise the attendance applicability provisions of
the HMR.
SPs 13484 and 14447 authorize ``attendance'' of the loading or
unloading of a cargo tank through the use of hoses equipped with cable
connected wedges, plungers, or flapper valves located at each end of
the hose, able to stop the flow of product from both the source and the
receiving tank within one second without human intervention in the
event of a hose rupture, disconnection, or separation. The SPs
prescribe inspection requirements and operational controls for use of
the hoses. In the NPRM, we proposed to revise paragraphs (i)(3) and
(i)(4) of Sec. 177.834 to adopt the provisions of SPs 13484 and 14447
in their entirety. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendments as proposed.
SPs 10597, 10803, 10882, 14618, and 14726 authorize the use of
diesel or propane fueled combustion cargo
[[Page 3661]]
heaters in motor vehicles used to transport Class 3 (flammable liquid)
or Division 2.1 (flammable gas) materials. The SPs prescribe
operational controls for use of heaters. In the NPRM, we proposed to
revise paragraph (l)(2)(i) of Sec. 177.834 to adopt the provisions of
these SPs in their entirety. In this final rule, because the existing
paragraph (l)(2)(ii) of Sec. 177.834 relating to the Effective date
for combustion heater requirements is obsolete, we are removing it as
proposed. In addition, we are redesignating paragraph (l)(2)(iii) of
Sec. 177.834 as paragraph (l)(2)(ii) as proposed in the NPRM. Because
we did not receive public comment on the proposal, adverse or
otherwise, in this final rule, we are adopting the amendment as
proposed.
Section 177.838
Section 177.838 prescribes operational requirements for the
transportation of Class 4 (flammable solid) materials, Class 5
(oxidizing) materials, and Division 4.2 (self-heating and pyrophoric
liquid) materials.
Notwithstanding the segregation requirements of Sec. 177.848(d),
SP 11373 authorizes the transport on the same transport vehicle of
``UN1384, Sodium hydrosulfite or sodium dithionite'' (PG II or III),
``UN3341, Thiourea dioxide'' (PG II or III); and ``UN3088, Self-
heating, solid, organic, n.o.s.'' (PG II or III) with Class 8
materials. The SP prescribes packaging and separation requirements. In
the NPRM, we proposed to revise the title of Sec. 177.838 and add a
new paragraph (i) to Sec. 177.838 to adopt the provisions of SP 11373
in its entirety. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed.
Section 177.840
Section 177.840 establishes specific operational requirements for
the transportation of Class 2 (gases) materials.
Notwithstanding the segregation requirements of Sec. 177.848(d),
SP 11043 authorizes the transport on the same transport vehicle of
Division 2.3, Hazard Zone A materials with materials classed as
Division 2.1, Class 3, Class 4, Class 5, and Class 8. The SP prescribes
packaging, marking, separation requirements.
Notwithstanding the segregation requirements of Sec. 177.848(d),
SP 14335 authorizes the transport on the same transport vehicle of
Division 2.3, Hazard Zone A materials with specification non-bulk
packagings and IBCs containing only the residue of Division 2.1, 4.3,
5.1, and Class 3 and 8 materials. The SP prescribes separation and
securement requirements, operational controls, quantity limitations,
and carrier safety rating requirements.
In the NPRM, we proposed to add a new paragraph (a)(3) to Sec.
177.840 to adopt the provisions of SPs 11043 and 14335 in their
entirety. Veolia supports the adoption of SP 11043; however, they
recommend the regulatory text proposed in Sec. 177.840(a)(3)(i) should
be revised to require a 4-foot separation rather than a 5-foot
separation for consistency with the segregation spacing requirements in
Sec. 173.12(e). We agree and are revising Sec. 177.840(a)(3)(i)
accordingly.
Section 177.841
Section 177.841 establishes specific operational requirements for
the transportation of Division 6.1 and Division 2.3 materials.
Notwithstanding the segregation requirements of Sec. 177.848(d),
SP 11151 authorizes transportation by private or contract motor carrier
of Division 6.1 PG I, Hazard Zone A materials meeting the definition of
a hazardous waste as defined in Sec. 171.8 on the same transport
vehicle with materials classed as Class 3, Class 4, Class 5, and Class
8. The Division 6.1 PG I, Hazard Zone A materials must be loaded on
pallets and separated from the Class 3, Class 4, Class 5, and Class 8
materials by a minimum horizontal distance of 2.74 m (9 feet). In the
NPRM, we proposed to add a new paragraph (f) to Sec. 177.841 to adopt
the provisions of SP 11151 in its entirety. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
F. Non-Bulk Packaging Specifications/IBCs
Part 172
Section 172.101
The Sec. 172.101 HMT designates the materials listed therein as
hazardous materials for the purpose of transportation of those
materials. For each listed material, the HMT identifies the hazard
class or specifies that the material is forbidden in transportation,
and provides the proper shipping name or directs the user to the
preferred proper shipping name. In addition, the HMT specifies or
references requirements in this subchapter pertaining to labeling,
packaging, quantity limits aboard aircraft, and stowage of hazardous
materials aboard vessels. In the NPRM, we proposed to revise several
entries in the HMT to adopt SPs relating to non-bulk packagings and
IBCs. Specifically, for ``UN1415, Lithium,'' ``UN2257, Potassium,''
``UN3190, Self-heating solid, inorganic, n.o.s.,'' ``UN1428, Sodium,''
``UN1381, Phosphorus, yellow, under water'' and ``UN2813, Water-
reactive solid, n.o.s.'' (Packing Group II and III), we proposed to add
a reference to Sec. 173.151 to provide packaging exceptions for
relevant Hazard Class 4 materials. In this final rule, the provisions
adopted for ``UN1381, Phosphorus, yellow, under water'' and ``UN2813,
Water-reactive solid, n.o.s.'' (Packing Group II and III) are moved to
the more appropriate Sec. Sec. 173.188 and the new Sec.
172.102(c)(3), Special provision B132 respectively. The revisions are
discussed in the following sections.
Part 173
Section 173.62
Section 173.62 prescribes packaging instructions for explosives.
SP 12335 authorizes the transportation by motor vehicle, cargo
vessel, and cargo aircraft when authorized in the HMT, and passenger-
carrying aircraft when authorized for carriage by the HMT and used
exclusively to transport personnel to remote work sites certain
Division 1.1D and 1.4D detonating cords without the ends being sealed
in alternative packaging, provided that the inner packaging containing
the detonating cord is made of a static-resistant plastic bag of at
least 3 mil thickness and the bag is securely closed for
transportation. In the NPRM, we proposed to adopt the provisions of SP
12335 in its entirety in Sec. 173.62. Because we did not receive
public comment on the proposal, adverse or otherwise, in this final
rule, we are adopting the amendment as proposed.
Section 173.150
Section 173.150 provides exceptions from the HMR for certain Class
3 (flammable liquid) material.
To codify SP 13217, in the NPRM, PHMSA proposed to add a paragraph
(h) to Sec. 173.150 that included an exception to permit Diesel fuel
(UN1202 or NA1993) and Gasoline (UN1203) to be transported one way, by
motor vehicle, directly from the loading location to an equipment
repair facility in non-specification non-bulk packaging, known as a
gasoline dispenser. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed.
Section 173.151
Section 173.151 provides exceptions for certain Class 4 materials.
[[Page 3662]]
In the NPRM, we proposed to add new paragraph (e) that would except
``UN1415, Lithium,'' ``UN2257, Potassium,'' and ``UN1428, Sodium,''
with a net quantity of material per inner packaging not exceeding 25
grams, from the labeling requirements of Part 172, Subpart E and the
placarding requirements of Part 172 Subpart F, if they are offered for
transportation or are transported in the packagings with conditions set
forth in that paragraph. We also proposed to codify SP 11736 by
establishing a new paragraph (f) to authorize shipments of ``UN3190,
Self-heating solid, inorganic, n.o.s,'' in unlined, non-DOT
specification multi-wall paper bags containing a maximum of 55 pounds
(net) weight. Because SP 11736 is no longer active, in this final rule,
we are not amending Sec. 173.151 to codify the SP. We further proposed
adding new paragraph (g) to authorize ``UN2813, Water reactive solid,
n.o.s. (contains magnesium, magnesium nitrides)'' in PG II or III to be
packaged in sift-proof bulk packagings. These revisions codify SPs
11602, 11736, 13796, and 15373. Because we did not receive public
comment on the proposals, adverse or otherwise, in this final rule, we
are adopting the amendments as proposed.
SP 11602 authorizes the transportation in commerce of certain
Division 4.3 materials contained in sift-proof closed bulk packagings
that prevent water from reaching the hazmat and have sufficient venting
to preclude a dangerous accumulation of gaseous emissions. In the NPRM,
we proposed to adopt the provisions of SP 11602 in its entirety in
Sec. 173.151(g). Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed. However, in this final rule, we are moving the
amendment to new Sec. 172.102(c)(3), Special provision B132 as it is a
more appropriate section for these provisions.
SP 13796 authorizes the transportation in commerce of ``UN1381,
Phosphorus, yellow, under water,'' in a 30 gallon UN 1A2 steel drum
certified at a minimum to the PG I performance level for solids and the
PG II performance level for liquids and, as a minimum, dual marked as
UN1A2/X400/S (for solids) and UN1A2 Y/1.4/150 (for liquids). In the
NPRM, we proposed to adopt the provisions of SP 13796 in its entirety
in Sec. 173.151. Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed. However, in this final rule, we are moving the
amendment to the most appropriate section for yellow phosphorus, Sec.
173.188; we are also removing the Sec. 173.151 column (8A) exception
reference to its HMT entry.
SP 15373 authorizes the manufacture, mark, sale and use of the
specially designed combination packagings for ``UN1415, Lithium,''
``UN2257, Potassium,'' and ``UN1428, Sodium,'' without hazard labels or
placards, for quantity limits not exceeding 25 grams. In the NPRM, we
proposed to adopt the provisions of SP 15373 in its entirety in new
Sec. 173.151(e). Because we did not receive public comment on the
proposal, adverse or otherwise, in this final rule, we are adopting the
amendment as proposed.
Section 173.154
Section 173.154 provides exceptions for Class 8, (corrosive)
materials.
In the NPRM, we proposed to codify SP 6614 by establishing a new
paragraph (b)(3) to authorize polyethylene bottles with rated
capacities of one gallon (3.785 liters), packed inside an open-top,
heavy wall, high density polyethylene box for shipping certain Packing
Group II and III corrosive liquids by private motor carrier. In this
final rule, we are adopting SP 6614 as proposed; however, we are moving
the amendment from paragraph (b) to new Sec. 172.102(c)(1), Special
provision 386, as it is a more appropriate location in the HMR.
In the NPRM, we also proposed to codify SP 14137 in new paragraph
(e) to authorize hydrochloric acid concentration not exceeding 38%, in
Packing Group II, to be packaged in UN31H1 or UN31HH1 intermediate bulk
containers when loaded in accordance with the requirements of Sec.
173.35(h). In this final rule, we are adopting SP 14137 as proposed;
however, we are moving the amendment from Sec. 173.154(e) to new Sec.
172.102(c)(3), Special provision B133, as it is a more appropriate
location in the HMR.
These amendments to Sec. 173.154 codify SP 6614 and 14137. Because
we did not receive public comment on the proposals, adverse or
otherwise, in this final rule, we are adopting the amendments as
proposed. However, the proposed provisions of SP 12030 are now codified
in Sec. 173.159(h)(2), as it is a more appropriate location in the HMR
for battery fluid packaging provisions.
Section 173.158
Section 173.158 prescribes the general requirements, authorized
packagings, and exceptions for nitric acid.
To codify SPs 8230, 9722, and 14213, we proposed in the NPRM to
establish a new paragraph (i) to authorize ``Nitric acid of up to 40%
concentration'' in a UN1H1 non-removable head plastic drum with certain
conditions set forth in that paragraph and add new paragraph (j) for
the transportation of ``Nitric acid, other than red fuming, with more
than 70% nitric acid'' and ``Nitric acid, other than red fuming, with
not more than 70% nitric acid'' in a combination packaging when offered
for transportation by rail, highway, or cargo vessel. Because of the
supportive public comments received as a result of our proposal, in
this final rule, we are adopting the amendments as proposed.
Section 173.159
Section 173.159 prescribes packaging, shipping specifications, and
exceptions for the transportation of wet electric storage batteries.
To codify SP 13548, in the NPRM, we proposed to revise paragraph
(e) to include shipments of electric storage batteries containing
electrolyte or corrosive battery fluid, and electric storage batteries
and battery acid. SP 13548 authorizes the transportation in commerce of
lead acid batteries and packages of battery acid with two different UN
numbers on the same motor vehicle with the packages secured against
shifting. Because of the supportive public comments received as a
result of our proposal, in this final rule, we are adopting the
amendments as proposed.
In the NPRM, we proposed to revise Sec. 173.154 by codifying SP
12030 in new paragraph (f). After comment review and our own analysis,
we believe this amendment is more appropriately codified in new Sec.
173.159(h)(2) along with the existing provision in new Sec.
173.159(h)(1). Special provision N6 of Sec. 172.102 specifies that
battery fluid, acid or alkali, when packaged with an electric storage
battery, wet or dry, is to be packaged as prescribed in Sec.
173.159(g) or (h). Thus, in this final rule, we are moving the
amendment from Sec. 173.154(f) to Sec. 173.159(h)(2) and codifying it
as proposed.
Section 173.181
Section 173.181 sets forth packaging and other requirements for
pyrophoric materials (liquids).
To codify SP 12920, in the NPRM, we proposed to add new paragraph
(d) to Sec. 173.181 that authorizes the transportation of certain
pyrophoric materials in a combination package consisting of UN1A2 outer
package and a UN1A1 inner package. Because we did not receive public
comment on the proposal, adverse or otherwise, in this final rule, we
are adopting the amendment as proposed.
[[Page 3663]]
Section 173.188
Section 173.188 prescribes the packaging instructions for white and
yellow phosphorus.
SP 13796 authorizes the transportation of ``UN1381, Phosphorus,
yellow, under water,'' in a 30 gallon UN 1A2 steel drum certified as a
minimum to the PG I performance level for solids and the PG II
performance level for liquids and, as a minimum, dual marked as UN1A2/
X400/S (for solids) and UN1A2 Y/1.4/150 (for liquids). In the NPRM, we
proposed to adopt the provisions of SP 13796 in its entirety in Sec.
173.151. Because we did not receive public comment on the proposal,
adverse or otherwise, in this final rule, we are adopting the amendment
as proposed. However, in this final rule, we are moving the amendment
to the most appropriate section for yellow phosphorus, Sec. 173.188;
we are also removing the Sec. 173.151 column (8A) exception reference
to its HMT entry.
VI. Regulatory Analyses and Notices
A. Statutory/Legal Authority for This Rulemaking
This rulemaking is issued under the authority of the Federal
hazardous materials transportation law (49 U.S.C. 5101 et seq.).
Section 5103(b) authorizes the Secretary of Transportation to prescribe
regulations for the safe transportation, including security, of
hazardous materials in intrastate, interstate, and foreign commerce.
This rulemaking codifies certain SPs into the HMR.
B. Executive Order 12866, Executive Order 13563, Executive Order 13610,
and DOT Regulatory Policies and Procedures
This final rule is not considered a significant regulatory action
under Executive Order 12866 (``Regulatory Planning and Review''), as
supplemented and reaffirmed by Executive Order 13563 (``Improving
Regulation and Regulatory Review''), stressing that, to the extent
permitted by law, an agency rulemaking action must be based on benefits
that justify its costs, impose the least burden, consider cumulative
burdens, maximize benefits, use performance objectives, and assess
available alternatives, and the Regulatory Policies and Procedures of
the Department of Transportation (44 FR 11034). Executive Orders 12866
and 13563 require agencies to regulate in the ``most cost-effective
manner,'' to make a ``reasoned determination that the benefits of the
intended regulation justify its costs,'' and to develop regulations
that ``impose the least burden on society.''
Executive Order 13610, issued May 10, 2012, urges agencies to
conduct retrospective analyses of existing rules to examine whether
they remain justified and whether they should be modified or
streamlined in light of changed circumstances, including the rise of
new technologies. By building off of each other, these three Executive
Orders require agencies to regulate in the ``most cost-effective
manner,'' to make a ``reasoned determination that the benefits of the
intended regulation justify its costs,'' and to develop regulations
that ``impose the least burden on society.''
In this final rule, PHMSA is amending the HMR to adopt provisions
contained in certain widely-used or long-standing SPs that have an
established safety record. The revisions are intended to provide wider
access to the regulatory flexibility offered in SPs and eliminate the
need for numerous renewal requests, thus reducing paperwork burdens and
facilitating commerce while maintaining an appropriate level of safety.
Although difficult to quantify, PHMSA assumes that for most regulated
entities in these categories, the revisions in this final rule require
little or no change to existing practice or behavior and incremental
compliance costs will thus be close to zero. At the same time, the
potential for additional safety benefits is also very limited in these
cases, as existing practice and operations are already minimizing the
number of incidents.
Estimated benefits associated with this rule result from the
regulated community no longer being required to apply for an SP and
amount to approximately $14,000 annually. Costs associated with the
rule are estimated to be negligible annually. Since existing SP holders
are already complying with the specifications of the current SPs, the
amendments adopted in this final rule would not impose new obligations
on current non-holders of SPs. The overall costs and benefits of the
rule are dependent on the level of pre-existing compliance and the
overall effectiveness of the new requirements specified in this
rulemaking.
C. Executive Order 13132
This final rule has been analyzed in accordance with the principles
and criteria contained in Executive Order 13132 (``Federalism''), 64 FR
43255 (Aug. 10. 1999) and the President's May 20, 2009 memorandum (74
FR 24693 [May 22, 2009]). The requirements in this final rule would
preempt state, local, and Indian tribe requirements but would not have
substantial direct effects on the States, the relationship between the
national government and the States, or the distribution of power and
responsibilities among the various levels of government. Therefore, the
consultation and funding requirements of Executive Order 13132 do not
apply.
The Federal hazardous materials transportation law, 49 U.S.C. 5101
et seq., contains an express preemption provision (49 U.S.C. 5125(b))
preempting State, local, and Indian tribe requirements on the following
subjects:
(1) The designation, description, and classification of hazardous
materials;
(2) The packing, repacking, handling, labeling, marking, and
placarding of hazardous materials;
(3) The preparation, execution, and use of shipping documents
related to hazardous materials and requirements related to the number,
contents, and placement of those documents;
(4) The written notification, recording, and reporting of the
unintentional release in transportation of hazardous material; or
(5) The design, manufacture, fabrication, marking, maintenance,
recondition, repair, or testing of a packaging or container
represented, marked, certified, or sold as qualified for use in
transporting hazardous material.
Federal hazardous materials transportation law provides at 49
U.S.C. 5125(b)(2) that, if DOT issues a regulation concerning any of
these subjects, DOT must determine and publish in the Federal Register
the effective date of Federal preemption. The effective date may not be
earlier than the 90th day following the date of issuance of the final
rule and not later than 2 years after the date of issuance.
This rule would address subject areas (1), (2), (3), and (5) above
and would preempt any state, local, or Indian tribe requirements
concerning these subjects unless the non-Federal requirements are
``substantively the same'' as the Federal requirements. The effective
date of Federal preemption is April 20, 2016.
D. Executive Order 13175
This final rule has been analyzed in accordance with the principles
and criteria contained in Executive Order 13175 (``Consultation and
Coordination with Indian Tribal Governments''). Because this final rule
does not have tribal implications and does not impose substantial
direct compliance costs, the funding and consultation requirements of
Executive Order 13175 do not apply.
[[Page 3664]]
E. Regulatory Flexibility Act, Executive Order 13272, and DOT
Procedures and Policies
The Regulatory Flexibility Act (5 U.S.C. 601 et seq.) requires an
agency to review regulations to assess their impact on small entities
unless the agency determines that a rule is not expected to have a
significant impact on a substantial number of small entities. The
primary costs to small entities associated with this rule include
developing and updating a risk assessment, developing and updating
operating procedures, and additional training for hazmat employees who
perform loading and unloading operations.
PHMSA expects the impacts of this rule will be limited for many
small entities due to their compliance with other existing Federal
regulations. In this rulemaking, PHMSA also explicitly acknowledges
that many regulated entities are holders of SPs or are part of industry
associations with voluntary codes of safe practice, and that these may
be sufficient for compliance with the final rule as long as all of the
relevant safety areas are addressed and documented. For regulated
entities in these categories, the rulemaking requires little or no
change to existing practices or behavior and incremental compliance
costs will thus be close to zero. Therefore, the benefit and cost
figures discussed below should be viewed as upper bounds, both of which
will be reduced by the extent of current practice.
PHMSA estimates that there are 50 potentially affected small
entities. The annualized documentation cost for developing and updating
the risk assessment and the operating procedures is estimated to be
$375 per small entity. The annualized cost of additional training for
affected employees is estimated to be approximately $5.50 per employee.
Further, PHMSA estimates that approximately 50% of small businesses are
already implementing procedures that would be compliant with this
rulemaking. Based upon the above estimates and assumptions, PHMSA
certifies that this rulemaking does not have a significant economic
impact on a substantial number of small entities. Further information
on the estimates and assumptions used to evaluate the potential impacts
to small entities is available in the Regulatory Impact Assessment that
has been placed in the public docket for this rulemaking.
F. Paperwork Reduction Act
PHMSA currently has an approved information collection under OMB
Control No. 2137-0051, entitled ``Special Permits and Approvals,''
expiring on May 31, 2018. Section 1320.8(d), Title 5, Code of Federal
Regulations, requires PHMSA to provide interested members of the public
and affected agencies an opportunity to comment on information
collection and recordkeeping requests. This rulemaking adds new
exceptions to the HMR while eliminating the need for persons to apply
for a SP, resulting in a decrease in burden. PHMSA estimates the
reduction in information collection burden as follows:
OMB Control No. 2137-0051: SPs and Approvals
Decrease in Annual Number of Respondents: 96
Decrease in Annual Responses: 96
Decrease in Annual Burden Hours: 194
Decrease in Annual Burden Cost: $14,027
There are 832 grantees associated with the 96 SPs being adopted in
this rulemaking. Over 10 years, a SP would on average be renewed twice,
resulting in 1,664 renewals (832 x 2). The average number of
applications per year would be approximately 166 (1,664/10). The annual
estimated cost savings would total $14,027 (166 number of renewals per
year x $39.50/hr. preparation cost + 166 renewals per year x $45.00/hr
compliance cost).
Please direct your requests for a copy of this final information
collection to Steven Andrews or T. Glenn Foster, Office of Hazardous
Materials Standards (PHH-12), Pipeline and Hazardous Materials Safety
Administration, 1200 New Jersey Avenue SE., 2nd Floor, Washington, DC,
20590-0001.
G. Regulatory Identifier Number (RIN)
A regulatory identifier number (RIN) is assigned to each regulatory
action listed in the Unified Agenda of Federal Regulations. The
Regulatory Information Service Center publishes the Unified Agenda in
April and October of each year. The RIN contained in the heading of
this document can be used to cross-reference this action with the
Unified Agenda.
H. Unfunded Mandates Reform Act
This rulemaking does not impose unfunded mandates under the
Unfunded Mandates Reform Act of 1995. PHMSA has concluded that the rule
will not impose annual expenditures of $141.3 million on State, local,
or tribal governments or the private sector, and thus does not require
an Unfunded Mandates Act analysis.
I. Executive Order 13609 and International Trade Analysis
Under E.O. 13609, agencies must consider whether the impacts
associated with significant variations between domestic and
international regulatory approaches are unnecessary or may impair the
ability of American business to export and compete internationally. In
meeting shared challenges involving health, safety, labor, security,
environmental, and other issues, international regulatory cooperation
can identify approaches that are at least as protective as those that
are or would be adopted in the absence of such cooperation.
International regulatory cooperation can also reduce, eliminate, or
prevent unnecessary differences in regulatory requirements.
Similarly, the Trade Agreements Act of 1979 (Pub. L. 96-39), as
amended by the Uruguay Round Agreements Act (Pub. L. 103-465),
prohibits Federal agencies from establishing any standards or engaging
in related activities that create unnecessary obstacles to the foreign
commerce of the United States. For purposes of these requirements,
Federal agencies may participate in the establishment of international
standards, so long as the standards have a legitimate domestic
objective, such as providing for safety, and do not operate to exclude
imports that meet this objective. The statute also requires
consideration of international standards and, where appropriate, that
they be the basis for U.S. standards.
PHMSA participates in the establishment of international standards
in order to protect the safety of the American public, and we have
assessed the effects of the rule to ensure that it does not cause
unnecessary obstacles to foreign trade. Accordingly, this rulemaking is
consistent with E.O. 13609 and PHMSA's obligations under the Trade
Agreement Act, as amended.
J. Environmental Assessment and NEPA Analysis
PHMSA is amending the HMR by adopting provisions contained in
certain widely-used or long-standing SPs that have an established
safety record. The revisions are intended to provide wider access to
the regulatory flexibility offered in SPs and eliminate the need for
numerous renewal requests, thus reducing paperwork burdens and
facilitating commerce while maintaining an appropriate level of safety.
The National Environmental Policy Act (NEPA), 42 U.S.C. 4321-4375,
requires that federal agencies analyze
[[Page 3665]]
proposed actions to determine whether the action will have a
significant impact on the human environment. The Council on
Environmental Quality (CEQ) regulations order federal agencies to
conduct an environmental review considering (1) the need for the
proposed action (2) alternatives to the proposed action (3) probable
environmental impacts of the proposed action and alternatives and (4)
the agencies and persons consulted during the consideration process. 40
CFR 1508.9(b). A detailed NEPA assessment has been placed in the docket
for this rulemaking for public review.
K. Privacy Act
Anyone is able to search the electronic form of any written
communications and comments received into any of our dockets by the
name of the individual submitting the document (or signing the
document, if submitted on behalf of an association, business, labor
union, etc.). You may review DOT's complete Privacy Act Statement in
the Federal Register published on April 11, 2000 (65 FR 19477) which
may be viewed at: http://www.gpo.gov/fdsys/pkg/FR-2000-04-11/pdf/00-8505.pdf.
L. National Technology Transfer and Advancement Act
The National Technology Transfer and Advancement Act of 1995 (15
U.S.C. 272 note) directs federal agencies to use voluntary consensus
standards in their regulatory activities unless doing so would be
inconsistent with applicable law or otherwise impractical. Voluntary
consensus standards are technical standards (e.g. specification of
materials, test methods, or performance requirements) that are
developed or adopted by voluntary consensus standard bodies. This final
rule does not involve voluntary consensus standards.
List of Subjects
49 CFR Part 107
Administrative practice and procedure, Hazardous materials
transportation, Penalties, Reporting and recordkeeping requirements.
49 CFR Part 171
Exports, Hazardous materials transportation, Hazardous waste,
Imports, Reporting and recordkeeping requirements.
49 CFR Part 172
Education, Hazardous materials transportation, Hazardous waste,
Labeling, Packaging and containers, Reporting and recordkeeping
requirements.
49 CFR Part 173
Hazardous materials transportation, Packaging and containers,
Radioactive materials, Reporting and recordkeeping requirements,
Uranium.
49 CFR Part 174
Hazardous materials transportation, Incorporation, Radioactive
materials, and Railroad safety.
49 CFR Part 176
Hazardous materials transportation, Maritime carriers, Radioactive
materials, Reporting and recordkeeping requirements.
49 CFR Part 177
Hazardous materials transportation, Motor carriers, Radioactive
materials, Reporting and recordkeeping requirements.
49 CFR Part 178
Hazardous materials transportation, Motor vehicle safety, Packaging
and containers, Reporting and recordkeeping requirements.
49 CFR Part 180
Hazardous materials transportation, Motor carriers, Motor vehicle
safety, Packaging and containers, Railroad safety, Reporting and
recordkeeping requirements.
In consideration of the foregoing, 49 CFR Chapter I is amended as
follows:
PART 107--HAZARDOUS MATERIALS PROGRAM PROCEDURES
0
1. The authority citation for part 171 continues to read as follows:
Authority: 49 U.S.C. 5101-5128, 44701; Public Law 101-410
section 4 (28 U.S.C. 2461 note); Public Law 104-121 sections 212-
213; Public Law 104-134 section 31001; Public Law 112-141 section
33006, 33010; 49 CFR 1.81 and 1.97.
0
2. In Sec. 107.1, revise the definitions for ``insufficient corrective
action'' and ``sufficient corrective action'' to read as follows:
Sec. 107.1 Definitions.
* * * * *
Insufficient corrective action means that either a PHMSA Field
Operations (FOPS) Division officer or an authorized representative or
special agent of DOT upon request, such as an Operating Administration
(OA) representative, has determined that evidence of an applicant's
corrective action in response to prior enforcement cases is inadequate
or incomplete and the basic safety management controls proposed for the
type of hazardous material, packaging, procedures, and/or mode of
transportation remain inadequate to prevent recurrence of a violation.
* * * * *
Sufficient corrective action means that either a PHMSA Field
Operations officer or an authorized representative or special agent of
DOT upon request, such as an Operating Administration (OA)
representative, has determined that evidence of an applicant's
corrective action in response to prior enforcement cases is sufficient
and the basic safety management controls proposed for the type of
hazardous material, packaging, procedures, and/or mode of
transportation are adequate.
* * * * *
PART 171--GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS
0
3. The authority citation for part 171 continues to read as follows:
Authority: 49 U.S.C. 5101-5128, 44701; 101, section 4 (28 U.S.C.
2461 note); Public Law 104-121, sections 212-213; Public Law 104-
134, section 31001; 49 CFR 1.81 and 1.97.
0
4. In Sec. 171.8, the definition of ``Display pack'' is added in
alphabetical sequence to read as follows:
Sec. 171.8 Definitions and abbreviations.
* * * * *
Display pack means a package intended to be placed at retail
locations which provide direct customer access to consumer commodities
contained within the package when all or part of the outer fiberboard
packaging is removed.
* * * * *
PART 172--HAZARDOUS MATERIALS TABLE, SPECIAL PROVISIONS, HAZARDOUS
MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, TRAINING
REQUIREMENTS, AND SECURITY PLANS
0
5. The authority citation for part 172 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; 44701; 49 CFR 1.81, 1.96 and
1.97.
0
6. In Sec. 172.101, the Hazardous Materials Table is amended by
revising entries under ``[REVISE]'' to read as follows:
Sec. 172.101 Purpose and use of hazardous materials table.
* * * * *
[[Page 3666]]
Sec. 172.101--Hazardous Materials Table
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Hazardous (8) packaging (Sec. 173.***) (9) Quantity limitations (10) Vessel stowage
materials Hazard ---------------------------------------------------------------------------------------------------------------------
Symbols descriptions and class or Identification PG Label codes Special provisions
proper shipping division No. (Sec. 172.102) Exceptions Non-bulk Bulk Passenger Cargo aircraft Location Other
names aircraft/rail only
(1) (2)............... (3) (4).............. (5)........ (6)............ (7)............... (8A)........... (8B)........... (8C)........... (9A)........... (9B)........... (10A).......... (10B)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
[REVISE]..........
* * * * * * *
Acrolein, 6.1 UN1092........... I.......... 6.1, 3......... 1, 380, B9, B14, None........... 226............ 244............ Forbidden...... Forbidden...... D.............. 40
stabilized. B30, B42, B77,
T22, TP2, TP7,
TP13, TP38, TP44.
* * * * * * *
Adhesives, 3 UN1133........... I.......... 3.............. T11, TP1, TP8, 150............ 201............ 243............ 1 L............ 30 L........... B..............
containing a TP27.
flammable liquid.
II......... 3.............. 149, 383, B52, 150............ 173............ 242............ 5 L............ 60 L........... B..............
IB2, T4, TP1, TP8.
III........ 3.............. B1, B52, IB3, T2, 150............ 173............ 242............ 60 L........... 220 L.......... A..............
TP1.
* * * * * * *
G............ Articles, 1.4S UN0349........... II......... 1.4S........... 101, 148, 382..... None........... 62............. None........... 25 kg.......... 100 kg......... 01............. 25
explosive, n.o.s.
* * * * * * *
Articles, 1.4G UN0431........... II......... 1.4G........... 381............... None........... 62............. None........... Forbidden...... 75 kg.......... 02............. 25
pyrotechnic for
technical
purposes.
* * * * * * *
Coating solution 3 UN1139........... I.......... 3.............. T11, TP1, TP8, 150............ 201............ 243............ 1 L............ 30 L........... B..............
(includes surface TP27.
treatments or
coatings used for
industrial or
other purposes
such as vehicle
undercoating,
drum or barrel
lining).
II......... 3.............. 149, IB2, T4, TP1, 150............ 202............ 242............ 5 L............ 60 L........... B..............
TP8, 383.
III........ 3.............. B1, IB3, T2, TP1.. 150............ 203............ 242............ 60 L........... 220 L.......... A..............
* * * * * * *
G............ Corrosive liquid, 8 UN3264........... I.......... 8.............. A6, B10, T14, TP2, None........... 201............ 243............ 0.5 L.......... 2.5 L.......... B.............. 40
acidic, TP27.
inorganic, n.o.s.
II......... 8.............. 386, B2, IB2, T11, 154............ 202............ 242............ 1 L............ 30 L........... B.............. 40
TP2, TP27.
III........ 8.............. IB3, T7, TP1, TP28 154............ 203............ 241............ 5 L............ 60 L........... A.............. 40
G............ Corrosive liquid, 8 UN3265........... I.......... 8.............. A6, B10, T14, TP2, None........... 201............ 243............ 0.5 L.......... 2.5 L.......... B.............. 40
acidic, organic, TP27.
n.o.s.
II......... 8.............. 148,B2, IB2, T11, 154............ 202............ 242............ 1 L............ 30 L........... B.............. 40
TP2, TP27.
III........ 8.............. 386, IB3, T7, TP1, 154............ 203............ 241............ 5 L............ 60 L........... A.............. 40
TP28.
G............ Corrosive liquid, 8 UN3266........... I.......... 8.............. A6, T14, TP2, TP27 None........... 201............ 243............ 0.5 L.......... 2.5 L.......... B.............. 40, 52
basic, inorganic,
n.o.s.
II......... 8.............. 386, B2, IB2, T11, 154............ 202............ 242............ 1 L............ 30 L........... B.............. 40, 52
TP2, TP27.
III........ 8.............. IB3, T7, TP1, TP28 154............ 203............ 241............ 5 L............ 60 L........... A.............. 40, 52
* * * * * * *
G............ Corrosive liquids, 8 NA1760........... I.......... 8.............. A6, A7, B10, T14, None........... 201............ 243............ 0.5 L.......... 2.5 L.......... B.............. 40
n.o.s. TP2, TP27.
[[Page 3667]]
II......... 8.............. 386, B2, IB2, T11, 154............ 202............ 242............ 1 L............ 30 L........... B.............. 40
TP2, TP27.
III........ 8.............. 386, IB3, T7, TP1, 154............ 203............ 241............ 5 L............ 60 L........... A.............. 40
TP28.
* * * * * * *
G............ Environmentally 9 UN3077........... III........ 9.............. 8, 146, 335, 384, 155............ 213............ 240............ No limit....... No limit....... A..............
hazardous A112, B54, B120,
substance, solid, IB8, IP3, N20,
n.o.s. N91, T1, TP33.
* * * * * * *
D............ Fusee (railway or 4.1 NA1325........... II......... 4.1............ 381............... None........... 184............ None........... 15 kg.......... 50 kg.......... B..............
highway).
* * * * * * *
Hydrochloric acid. 8 UN1789........... II......... 8.............. 386, A3, A6, B3, 154............ 202............ 242............ 1 L............ 30 L........... C..............
B15, B133, IB2,
N41, T8, TP2.
III........ 8.............. A3, IB3, T4, TP1.. 154............ 203............ 241............ 5 L............ 60 L........... C.............. 8
* * * * * * *
Hypochlorite 8 UN1791........... II......... 8.............. 148, A7, B2, B15, 154............ 202............ 242............ 1 L............ 30 L........... B.............. 26
solutions. IB2, IP5, N34,
T7, TP2, TP24.
III........ 8.............. 386, IB3, N34, T4, 154............ 203............ 241............ 5 L............ 60 L........... B.............. 26
TP2, TP24.
* * * * * * *
Lithium........... 4.3 UN1415........... I.......... 4.3............ A7, A19, IB4, IP1, 151............ 211............ 244............ Forbidden...... 15 kg.......... E.............. 13, 52, 148
N45.
* * * * * * *
D G.......... Other regulated 9 NA3077........... III........ 9.............. 384, B54, IB8, 155............ 213............ 240............ No limit....... No limit....... A..............
substances, IP2, T1, TP33.
solid, n.o.s.
* * * * * * *
Paint including 3 UN1263........... I.......... 3.............. 367, T11, TP1, 150............ 201............ 243............ 1 L............ 30 L........... E..............
paint, lacquer, TP8, TP27.
enamel, stain,
shellac
solutions,
varnish, polish,
liquid filler and
liquid lacquer
base.
II......... 3.............. 149, 367, 383, 150............ 173............ 242............ 5 L............ 60 L........... B..............
B52, B131, IB2,
T4, TP1, TP8,
TP28.
III........ 3.............. 367, B1, B52, 150............ 173............ 242............ 60 L........... 220 L.......... A..............
B131, IB3, T2,
TP1, TP29.
* * * * * * *
Paint related 3 UN1263........... I.......... 3.............. 367, T11, TP1, 150............ 201............ 243............ 1 L............ 30 L........... E..............
material TP8, TP27.
including paint
thinning, drying,
removing, or
reducing compound.
3 UN1263........... II......... 3.............. 149, 367, 383, 150............ 173............ 242............ 5 L............ 60 L........... B..............
B52, B131, IB2,
T4, TP1, TP8,
TP28.
III........ 3.............. 367, B1, B52, 150............ 173............ 242............ 60 L........... 220 L.......... A..............
B131, IB3, T2,
TP1, TP29.
* * * * * * *
Petroleum gases, 2.1 UN1075........... ........... 2.1............ T50, N95.......... 306............ 304............ 314, 315....... Forbidden...... 150 kg......... E.............. 40
liquefied or
Liquefied
petroleum gas.
* * * * * * *
Potassium......... 4.3 UN2257........... I.......... 4.3............ A7, A19, A20, B27, 151............ 211............ 244............ Forbidden...... 15 kg.......... D.............. 52
IB4, IP1, N6,
N34, T9, TP7,
TP33.
[[Page 3668]]
* * * * * * *
Printing ink, 3 UN1210........... I.......... 3.............. 367, T11, TP1, TP8 150............ 201............ 243............ 1 L............ 30 L........... E..............
flammable or
Printing ink
related material
(including
printing ink
thinning or
reducing
compound),
flammable.
II......... 3.............. 149, 367, 383, 150............ 173............ 242............ 5 L............ 60 L........... B..............
IB2, T4, TP1, TP8.
III........ 3.............. 367, B1, IB3, T2, 150............ 173............ 242............ 60 L........... 220 L.......... A..............
TP1.
* * * * * * *
Propane, see also 2.1 UN1978........... ........... 2.1............ 19, T50, N95...... 306............ 304............ 314, 315....... Forbidden...... 150 kg......... E.............. 40
Petroleum gases,
liquefied.
* * * * * * *
Resin Solution, 3 UN1866........... I.......... 3.............. B52, T11, TP1, 150............ 201............ 243............ 1 L............ 30 L........... E..............
flammable. TP8, TP28.
II......... 3.............. 149, 383, B52, 150............ 173............ 242............ 5 L............ 60 L........... B.............. ..............
IB2, T4, TP1, TP8.
III........ 3.............. B1, B52, IB3, T2, 150............ 173............ 242............ 60 L........... 220 L.......... A.............. ..............
TP1.
* * * * * * *
G............ Self-heating 4.2 UN3088........... II......... 4.2............ IB6, IP2, T3, TP33 None........... 212............ 241............ 15 kg.......... 50 kg.......... C..............
solid, organic,
n.o.s.
III........ 4.2............ B116, B130, IB8, None........... 213............ 241............ 25 kg.......... 100 kg......... C..............
IP3, TP33.
* * * * * * *
Signal devices, 1.4G UN0191........... II......... 1.4G........... 381............... None........... 62............. None........... Forbidden...... 75 kg.......... 02............. 25
hand.
Signal devices, 1.4S UN0373........... II......... 1.4S........... 381............... None........... 62............. None........... 25 kg.......... 100 kg......... 01............. 25
hand.
* * * * * * *
Signals, railway 1.4S UN0193........... II......... 1.4S........... 381............... None........... 62............. None........... 25 kg.......... 100 kg......... 01............. 25
track, explosive.
* * * * * * *
Sodium............ 4.3 UN1428........... I.......... 4.3............ A7, A8, A19, A20, 151............ 211............ 244............ Forbidden...... 15 kg.......... D.............. 52
B9, B48, B68,
IB4, IP1, N34,
T9, TP7, TP33,
TP46.
* * * * * * *
Sulfuric acid with 8 UN2796........... II......... 8.............. 386, A3, A7, B2, 154............ 202............ 242............ 1 L............ 30 L........... B..............
not more than 51% B15, IB2, N6,
acid. N34, T8, TP2.
* * * * * * *
D............ Toy caps.......... 1.4S NA0337........... II......... 1.4S........... 382............... None........... 62............. None........... 25 kg.......... 100 kg......... 01............. 25
[[Page 3669]]
* * * * * * *
Trinitroresorcinol 1.1D UN0394........... II......... 1.1D........... 385............... None........... 62............. None........... Forbidden...... Forbidden...... 04............. 25, 5E
, wetted or
Styphnic acid,
wetted with not
less than 20
percent water, or
mixture of
alcohol and water
by mass.
* * * * * * *
G............ Water-reactive 4.3 UN2813........... I.......... 4.3............ IB4, N40, T9, TP7, None........... 211............ 242............ Forbidden...... 15 kg.......... E.............. 40
solid, n.o.s. TP33.
II......... 4.3............ B132, IB7, IP2, 151............ 212............ 242............ 15 kg.......... 50 kg.......... E.............. 40
T3, TP33.
III........ 4.3............ B132, IB8, IP4, 151............ 213............ 241............ 25 kg.......... 100 kg......... E.............. 40
T1, TP33.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 3670]]
* * * * *
0
7. In Sec. 172.102:
0
a. In paragraph (c)(1), special provisions 380, 381, 382, 383, 384,
385, and 386 are added in numerical sequence.
0
b. In paragraph (c)(3), special provisions B130, B131, B132, and B133
are added in numerical sequence.
0
c. In paragraph (c)(5), special provision N95 is added in numerical
sequence.
The additions are to read as follows:
Sec. 172.102 Special provisions.
* * * * *
(c) * * *
(1) * * *
380 For transportation by private carrier in a motor carrier only,
this material is not subject to the segregation requirements of Sec.
177.848(d) of this subchapter under the following conditions:
a. The material is packaged in a DOT Specification 4BW240 cylinder,
or in a DOT-51 portable tank.
b. The material may only be loaded with Class 3, Class 8, and
Division 4.1 materials in Packing Group II or III.
c. The motor carrier must maintain a satisfactory safety rating as
prescribed in 49 CFR part 385.
381 For railroad flagging kits, see Sec. 173.184 (c) of this
subchapter.
382 Packages containing toy plastic or paper caps for toy pistols
described as ``UN0349, Articles, explosive, n.o.s. (Toy caps), 1.4S''
or ``NA0337, Toy caps, 1.4S'' are not subject to the subpart E
(labeling) requirements of this part when offered for transportation by
motor vehicle, rail freight, cargo vessel, and cargo aircraft and,
notwithstanding the packing method assigned in Sec. 173.62 of this
subchapter, in conformance with the following conditions:
a. The toy plastic or paper caps must be in the form of sheets,
strips, rolls, or individual caps;
b. The caps must not contain more than an average of twenty-five
hundredths of a grain of explosive composition per cap;
c. The caps must be packed inside packagings constructed of
cardboard not less than 0.013-inch in thickness, metal not less than
0.008-inch in thickness, non-combustible plastic not less than 0.015-
inch in thickness, or a composite blister package consisting of
cardboard not less than 0.013-inch in thickness and non-combustible
plastic not less than 0.005-inch in thickness that completely encloses
the caps;
d. The minimum dimensions of each side and each end of the
cardboard packaging must be 1/8th inch in height or more;
e. The number of caps inside each packaging must be limited so that
not more than 10 grains of explosives composition may be packed into
one cubic inch of space, and not more than 17.5 grains of the explosive
composition of toy caps may be packed in any inner packaging;
f. Inner packagings must be packed in outer packagings meeting PG
II performance criteria;
g. Toy caps may be packed with non-explosive or non-flammable
articles provided the outer packagings are marked as prescribed in this
paragraph;
h. Toy paper caps of any kind must not be packed in the same
packaging with fireworks;
i. The outside of each package must be plainly marked ``ARTICLES,
EXPLOSIVES, N.O.S. (TOY CAPS)--HANDLE CAREFULLY'' OR ``TOY CAPS--HANDLE
CAREFULLY''; and
j. Explosives shipped in conformance with this paragraph must have
been examined in accordance with Sec. 173.56 of this subchapter and
approved by the Associate Administrator.
383 For transportation by motor vehicle, substances meeting the
conditions for high viscosity flammable liquids as prescribed in Sec.
173.121(b)(1)(i), (b)(1)(ii), and (b)(1)(iv) of this subchapter, may be
reassigned to Packing Group III under the following conditions:
a. Packaging must be UN standard metal drums attached with heavy
duty steel strapping to a pallet; and
b. The capacity of each drum must not exceed 220 L (58 gallons).
384 For green graphite electrodes and shapes that are large single
component solid objects not subject to shifting, transport in open rail
flat cars, open bed motor vehicles, and intermodal containers is also
authorized. The objects must be secured to the flat car, motor vehicle,
intermodal container, or unitized by steel banding to wooden runners or
pallets and the units secured to the flat car, motor vehicle, or
freight container to prevent shifting and movement, including relative
motion between the objects, under conditions normally incident to
transportation. Stacking is permitted two or more levels high to
achieve maximum allowable utilization of the designated vehicle, rail
car weight, or intermodal freight container weight or vessel hold
volume.
385 Notwithstanding the provisions of Sec. 177.834(l) of this
subchapter, cargo heaters may be used when weather conditions are such
that the freezing of a wetted explosive material is likely. Shipments
must be made by private, leased or contract carrier vehicles under
exclusive use of the offeror. Cargo heaters must be reverse
refrigeration (heat pump) units. Shipments made in accordance with this
Special provision are excepted from the requirements of Sec.
173.60(b)(4) of this subchapter.
386 When transported by private motor carrier only, the following
corrosive liquids may be packaged in polyethylene bottles with a
capacity no greater than 3.785L (one gallon), further packed inside an
open-top, heavy wall, high density polyethylene box (i.e., crate) in a
manner that the polyethylene bottles are not subjected to any
superimposed weight, and the boxes must be reasonably secured against
movement within the transport vehicle and loaded so as to minimize the
possibility of coming in contact with other lading:
Compounds, cleaning liquid, NA1760, PG II or III;
Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II;
Corrosive liquid, acidic, organic, n.o.s., UN 3265, PG III;
Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II;
Hypochlorite solutions, UN1791, PG III;
Hydrochloric acid solution, UN 1789, PG II; and
Sulfuric acid, UN2796, PG II.
a. No more than four bottles, securely closed with threaded caps,
may be packed in each box.
b. Each empty bottle must have a minimum weight of not less than
140 grams and a minimum wall thickness of not less than 0.020 inch
(0.508 mm).
c. The completed package must meet the Packing Group II performance
level, as applicable for combination packagings with a plastic box
outer packaging, in accordance with subpart M of part 178 of this
subchapter.
(i) Tests must be performed on each type and size of bottle, for
each manufacturing location. Samples taken at random must withstand the
prescribed tests without breakage or leakage.
(ii) One bottle for every two hours of production, or for every
2500 bottles produced, must be tested by dropping a bottle filled to
98% capacity with water from a height of 1.2 meters (3.9 feet) onto
solid concrete directly on the closure.
(iii) A copy of the test results must be kept on file at each
facility where packagings are offered for transportation, and must be
made available to a representative of the Department upon request.
(iv) The name or symbol of the bottle producer, and the month and
year of manufacture, must be marked by
[[Page 3671]]
embossing, ink-jet printing of permanent ink, or other permanent means
on the face or bottom of each bottle, in letters and numbers at least 6
mm (0.2 inch) high. Symbols, if used, must be registered with the
Associate Administrator.
(v) The box must be constructed from high-density polyethylene in
the density range 0.950-0.962, and be capable of holding liquid when in
the upright position.
* * * * *
(3) * * *
B130 When transported by motor vehicle, used diatomaceous earth
filter material is not subject to any other requirements of this
subchapter except for the shipping paper requirements of subpart C of
part 172 of this subchapter; emergency response information as required
by Sec. 172.602(a)(2) through (a)(7) of this subchapter; and the
marking requirements of Sec. 172.302 of this subchapter, if the
following requirements are met:
a. Packagings are non-DOT specification sift-proof motor vehicles
or sift-proof roll-on/roll-off bulk bins, which are covered by a
tarpaulin or other equivalent means.
b. The temperature of the material at the time it is offered for
transport and during transportation may not exceed 55 [deg]C (130
[deg]F).
c. The time between offering the material for transportation at the
point of origin, and unloading the material at the destination does not
exceed 48 hours.
d. In addition to the training requirements prescribed in
Sec. Sec. 172.700 through 172.704, each driver must be trained
regarding the properties and hazards of diatomaceous earth filter
material, precautions to ensure safe transport of the material, and
actions to be taken in the event of an emergency during transportation,
or a substantial delay in transit.
B131 When transported by highway, rail, or cargo vessel, waste
Paint and Paint related material (UN1263; PG II and PG III), when in
plastic or metal inner packagings of not more than 26.5 L (7 gallons),
are excepted from the marking requirements in Sec. 172.301(a) and (c)
and the labeling requirements in Sec. 172.400(a), when further packed
in the following specification and non-specification bulk outer
packagings and under the following conditions:
a. Primary receptacles must conform to the general packaging
requirements of subpart B of part 173 of this subchapter and may not
leak. If they do leak, they must be overpacked in packagings conforming
to the specification requirements of part 178 of this subchapter or in
salvage packagings conforming to the requirements in Sec. 173.12 of
this subchapter.
b. Primary receptacles must be further packed in non-specification
bulk outer packagings such as cubic yard boxes, plastic rigid-wall bulk
containers, dump trailers, and roll-off containers. Bulk outer
packagings must be liquid tight through design or by the use of lining
materials.
c. Primary receptacles may also be further packed in specification
bulk outer packagings. Authorized specification bulk outer packagings
are UN11G fiberboard intermediate bulk containers (IBC) and UN13H4
woven plastic, coated and with liner flexible intermediate bulk
containers (FIBCs) meeting the Packing Group II performance level and
lined with a plastic liner of at least 6 mil thickness.
d. All inner packagings placed inside bulk outer packagings must be
blocked and braced to prevent movement during transportation that could
cause the container to open or fall over. Specification IBCs and FIBCs
are to be secured to a pallet.
B132 Except for transportation by aircraft, UN2813, Water reactive
solid, n.o.s. (contains magnesium, magnesium nitrides) in PG II or III
may be packaged in sift-proof bulk packagings that prevent liquid from
reaching the hazardous material with sufficient venting to preclude
dangerous accumulation of flammable, corrosive or toxic gaseous
emissions such as methane, hydrogen and ammonia.
B133 Hydrochloric acid concentration not exceeding 38%, in Packing
Group II, is authorized to be packaged in UN31H1 or UN31HH1
intermediate bulk containers when loaded in accordance with the
requirements of Sec. 173.35(h) of this subchapter.
(5) * * *
* * * * *
N95 UN1075, Liquefied petroleum gas and UN1978, Propane authorized
for transport in DOT 4BA240 cylinders is not subject to the UN
identification number and proper shipping name marking or the label
requirements of this part subject to the following conditions:
a. The cylinder must be transported in a closed motor vehicle
displaying FLAMMABLE GAS placards in accordance with subpart F of part
172 of this subchapter.
b. Shipping papers at all times must reflect a correct current
accounting of all cylinders both full and expended.
c. The cylinders are collected and transported by a private or a
contract carrier for reconditioning, reuse or disposal.
* * * * *
0
8. In 172.202, paragraph (c) is revised to read as follows:
Sec. 172.202 Description of hazardous material on shipping papers.
* * * * *
(c)(1) The total quantity of the material covered by one
description must appear before or after, or both before and after, the
description required and authorized by this subpart. The type of
packaging and destination marks may be entered in any appropriate
manner before or after the basic description. Abbreviations may be used
to express units of measurement and types of packagings.
(2) Hazardous materials and hazardous substances transported by
highway considered ``household wastes'' as defined in 40 CFR 261.4, and
not subject to the Environmental Protection Agency's hazardous waste
regulations in 40 CFR parts 262 and 263, are excepted from the
requirements of this paragraph.
* * * * *
0
9. In 172.315 paragraph (a)(3) is added to read as follows:
Sec. 172.315 Limited quantities.
(a) * * *
(3) Except for Class 1 and 7, and Division 6.1 and 6.2 materials,
for highway transportation by private motor carrier, the limited
quantity marking is not required to be displayed on a package
containing materials assigned to Packing Group II and III prepared in
accordance with the limited quantity requirements in subpart B of part
173 of this subchapter provided:
(i) Inner packagings for liquid hazardous materials do not exceed
1.0 L (0.3 gallons) net capacity each;
(ii) Inner packagings for solid hazardous materials do not exceed
1.0 kg (2.2 pounds) net capacity each;
(iii) No more than 2 L (0.6 gallons) or 2 kg (4.4 pounds) aggregate
net quantity of any one hazardous material is transported per vehicle;
(iv) The total gross weight of all the limited quantity packages
per vehicle does not exceed 60 kg (132 pounds); and
(v) Each package is marked with the name and address of the
offeror, a 24-hour emergency response telephone number and the
statement ``Contains Chemicals'' in letters at least 25 mm (one-inch)
high on a contrasting background.
* * * * *
0
10. In Sec. 172.400a, paragraph (a)(1) is revised and paragraph (a)(8)
is added to read as follows:
[[Page 3672]]
Sec. 172.400a Exceptions from labeling.
(a) * * *
(1) A Dewar flask meeting the requirements in Sec. 173.320 of this
subchapter or a cylinder containing a Division 2.1, 2.2, or 2.3
material that is durably and legibly marked in accordance with CGA C-7,
Appendix A (IBR; see Sec. 171.7 of this subchapter). Notwithstanding
this exception, overpacks must be labeled (see Sec. 173.25 of this
subchapter).
* * * * *
(8) Packages containing toy plastic or paper caps for toy pistols
described as ``UN0349, Articles, explosive, n.o.s. (Toy caps), 1.4S''
or ``NA0337, Toy caps, 1.4S'' when offered in conformance with the
conditions of Sec. 172.102(c)(1), Special provision 382.
* * * * *
PART 173--SHIPPERS--GENERAL REQUIREMENTS FOR SHIPMENTS AND
PACKAGINGS
0
11. The authority citation for part 173 continues to read as follows:
Authority: 49 U.S.C. 5101-5128, 44701; 49 CFR 1.81, 1.96 and
1.97.
0
12. In Sec. 173.12, add paragraph (h) to read as follows:
Sec. 173.12 Exceptions for shipment of waste materials.
* * * * *
(h) Shrink-wrapped or stretch-wrapped pallets of limited quantity
waste. Shrink-wrapped or stretch-wrapped pallets containing packages of
waste ORM-D or limited quantity materials may be transported by motor
vehicle and cargo vessel under the following conditions:
(1) The waste materials must be in their original undamaged
packaging and marked with the ``Consumer Commodity ORM-D'' marking in
conformance with Sec. 172.316 or an authorized limited quantity
marking in conformance with Sec. 172.315 of this subchapter, as
appropriate. The word ``waste'' in association with the proper shipping
name is not required on individual packages;
(2) Packages must be securely affixed to a pallet and shrink-
wrapped or stretch-wrapped;
(3) The outside of the shrink-wrap or stretch-wrap must be marked
on opposite sides with either ``Waste, Consumer Commodity, ORM-D'' or
``Waste, Limited Quantity.''
0
13. In Sec. 173.29, paragraph (f) is added to read as follows:
Sec. 173.29 Empty packagings.
* * * * *
(f) Smokeless powder residue when transported by motor vehicle or
container/trailer in container-on-flatcar (COFC) or trailer-on-flatcar
(TOFC) service is excepted from subpart C (shipping papers) and the
subpart F (placarding) requirements of part 172 of this subchapter when
transported in conformance with the following:
(1) The outer packaging must be:
(i) A UN specification 1G fiber drum or 1A2 steel drum; or
(ii) A UN specification 4G fiberboard box or non-specification
fiberboard box containing plastic receptacle inner packagings with not
more than 2.5 grams of smokeless powders in each inner packaging;
(2) The amount of smokeless powder per outer packaging does not
exceed 5 grams;
(3) The smokeless powder is approved in accordance with Sec.
173.56 as a Class 1 explosive material;
(4) The empty packages must be transported in a closed transport
vehicle;
(5) The empty packages must be loaded by the shipper and unloaded
by the shipper or consignee; and
(6) The hazardous materials description to be used for the material
is ``RESIDUE: Last Contained Powder, smokeless, Hazard Class N/A,
Identification Number N/A, Packing Group N/A''.
* * * * *
0
14. In Sec. 173.40, revise paragraph (d)(1)(ii) to read as follows:
Sec. 173.40 General packaging requirements for toxic materials
packaged in cylinders.
* * * * *
(d) * * *
(1) * * *
(ii) Each cylinder with a valve must be equipped with a protective
metal or plastic cap, other valve protection device, or an overpack
which is sufficient to protect the valve from breakage or leakage
resulting from a drop of 2.0 m (7 ft) onto a non-yielding surface, such
as concrete or steel. Impact must be at an orientation most likely to
cause damage.
* * * * *
0
15. In Sec. 173.62, Packing Instruction 139 in the paragraph (c)(5)
Table of Packing Methods is revised to read as follows:
Sec. 173.62 Specific packaging requirements for explosives.
* * * * *
(c) * * *
(5) * * *
Table of Packing Methods
----------------------------------------------------------------------------------------------------------------
Packing instruction Inner packagings Intermediate packagings Outer packagings
----------------------------------------------------------------------------------------------------------------
* * * * * * *
139.................................. Bags................... Not necessary.......... Boxes.
PARTICULAR PACKING REQUIREMENTS OR
EXCEPTIONS:
1. For UN0065, 0102, 0104, 0289
and 0290, the ends of the
detonating cord must be sealed,
for example, by a plug firmly
fixed so that the explosive
cannot escape. The ends of CORD
DETONATING flexible must be
fastened securely.
2. For UN0065, 0104, 0289, 0290
the ends of the detonating cord
are not required to be sealed
provided the inner packaging
containing the detonating cord
consists of a static-resistant
plastic bag of at least 3 mil
thickness and the bag is
securely closed.
3. For UN0065 and UN0289, inner
packagings are not required when
they are fastened securely in
coils.
* * * * * * *
----------------------------------------------------------------------------------------------------------------
[[Page 3673]]
* * * * *
0
16. In Sec. 173.150, add paragraph (h) to read as follows:
Sec. 173.150 Exceptions for Class 3 (flammable and combustible
liquids).
* * * * *
(h) Diesel fuel (NA1993) and Gasoline (UN1203) may be transported
one way, by motor vehicle, directly from the loading location to an
equipment repair facility, in a non-DOT specification, non-bulk
packaging, known as a gasoline dispenser, that has been removed from
service at a fueling station under the following conditions:
(1) Prior to loading, each dispenser must be prepared for
transportation by capping or plugging all product inlet and outlet
piping, so that no fluid may be released during transportation;
(2) No dispenser may contain more than 2 gallons of gasoline; and
(3) Each dispenser must be blocked, braced or strapped to the motor
vehicle in accordance with the requirements of this subchapter to
prevent shifting during transportation.
0
17. In Sec. 173.151, paragraph (e) is added to read as follows:
Sec. 173.151 Exceptions for Class 4.
* * * * *
(e) For transportation by motor vehicle only, Lithium (UN1415),
Potassium (UN2257), and Sodium (UN1428) with a net quantity of material
per inner packaging not exceeding 25 grams, are excepted from the
labeling requirements of part 172, subpart E and the placarding
requirements of part 172, subpart F of this subchapter, when offered
for transportation in the following packagings under the following
conditions:
(1) Packaging. (i) The hazardous material is placed in a tightly
closed plastic bottle after being submerged in mineral oil;
(ii) The plastic bottle is placed inside a plastic bag that is
securely closed to prevent leaks or punctures;
(iii) The bagged bottle is then be placed inside a metal can with
all void spaces filled with an oil-absorbing material and sealed tight;
and
(iv) The can is then placed into a heat sealed barrier bag.
(2) Marking. Each inner plastic bottle, outer metal can, and
barrier bag must be marked with: Chemical name; quantity; and the name
and address of the offeror. Each outer packaging must be marked with
the proper shipping name and identification number in conformance with
Sec. 172.301. Additionally, each outer packaging must be marked, ``FOR
TRANSPORT BY MOTOR VEHICLE ONLY.''
(3) Recordkeeping. (i) Records of the preparation, packaging, and
marking of each chemical must be documented and all components in each
package must be noted; and
(ii) Records must be retained for a minimum of 5 years and be
accessible at or through the shipper's principal place of business and
be made available, upon request, to the Associate Administrator or
designated official.
0
18. In Sec. 173.156, paragraphs (c) and (d) are added to read as
follows:
Sec. 173.156 Exceptions for limited quantity and ORM.
* * * * *
(c) Display packs. Display packs, as defined in Sec. 171.8 of this
subchapter, of consumer commodity or limited quantity packages that
exceed 30 kg gross weight limitation may be transported by container/
trailer in trailer-on-flatcar (TOFC) or container-on-flat-car (COFC)
service, roadrailer and/or railrunner trailers, motor vehicle, or cargo
vessel under the following conditions:
(1) Packaging. Combination packages must conform to the
requirements of Subpart B of this part and meet the following, as
appropriate:
(i) Primary containers must conform to the quantity limits for
inner packagings prescribed in Sec. Sec. 173.150(b), 173.152(b),
173.154(b), 173.155(b) and 173.306(a) and (b), as appropriate;
(ii) Primary containers must be packed into trays that secure
individual containers from shifting inside the completed combination
package during transportation;
(iii) Tray(s) must be placed into a fiberboard box, and the
fiberboard box must be banded and secured to a pallet by metal, fabric,
or plastic straps to form a single palletized unit; and
(iv) The maximum net quantity of hazardous material permitted in
one palletized unit is 550 kg (1,210 lbs.).
(2) Marking. The outside of each package must be plainly and
durably marked in accordance with one of the following, as appropriate:
(i) As a consumer commodity as prescribed in Sec. 172.316 of this
subchapter; or
(ii) As a limited quantity as prescribed in Sec. 172.315 of this
subchapter.
(d) Exceptions for waste limited quantities and ORM-D materials.
Exceptions for certain waste limited quantity and ORM-D materials are
prescribed in Sec. 173.12(h).
0
19. In Sec. 173.158, paragraphs (i) and (j) are added to read as
follows:
Sec. 173.158 Nitric acid.
* * * * *
(i) Nitric acid solutions of concentrations up to 40%, nitric acid
by weight when offered for transportation or transported by rail,
highway, or cargo vessel, may be packaged in a UN1H1 non-removable head
plastic drum, tested and marked at the PG II performance level for
liquids with a specific gravity of at least 1.8, and a hydrostatic test
pressure appropriate for the hazardous material.
(1) Each drum may only be used one time and must be destroyed after
emptying.
(2) Each drum must be permanently and legibly marked ``Single Trip
Only'' and ``Must be Destroyed When Empty.''
(j) Nitric acid solutions, other than red fuming, with more than
70% nitric acid and Nitric acid solutions, other than red fuming, with
not more than 70% nitric acid, when offered for transportation or
transported by rail, highway, cargo vessel, or cargo-only aircraft may
be packaged in a UN 4G outer fiberboard box meeting the Packing Group I
or II performance level, as appropriate, subject to the following
conditions:
(1) Inner packaging: A plastic (``fluorinated ethylene-propylene''
[FEP] polymers, ``perfluoroalkoxy'' [PFA] polymers or similar
materials) bottle with lined screw closure meeting the compatibility
requirements of Sec. 173.24(e) of this section and having a net
capacity not greater than 2.5 liters (0.66 gallon) each. For cargo-only
aircraft, the inner packaging for PG I material may not exceed 1 L (0.3
gal) capacity. The wall thickness of the bottle must not be less than
0.020''.
(2) Intermediate packaging: (i) A tightly closed rigid-foam plastic
receptacle each containing one inner packaging; or
(ii) A plastic bag containing one inner packaging and placed inside
a heavy-wall polypropylene bag lined with polypropylene absorbent
material of sufficient capacity to completely absorb the liquid
contents of each inner package. Both bags must be tightly sealed with
either plastic tape, a wire tie or a cable tie.
0
20. In Sec. 173.159:
0
a. The paragraph (e) introductory text is revised.
0
b. Paragraph (h) is revised.
0
c. Paragraph (j) is added.
The revisions and additions read as follows:
Sec. 173.159 Batteries, wet.
* * * * *
(e) When transported by highway or rail, electric storage batteries
containing electrolyte, acid, or alkaline corrosive battery fluid and
electric storage batteries packed with electrolyte, acid,
[[Page 3674]]
or alkaline corrosive battery fluid, are not subject to any other
requirements of this subchapter, if all of the following are met:
* * * * *
(h)(1) Dry batteries or battery charger devices may be packaged in
4G fiberboard boxes with inner receptacles containing battery fluid.
Completed packages must conform to the Packing Group III performance
level. Not more than 12 inner receptacles may be packed in one outer
box. The maximum authorized gross weight for the completed package is
34 kg (75 pounds).
(2) Battery fluid, acid (UN2796) may be packaged in a UN6HG2
composite packaging further packed in a UN4G fiberboard box with a dry
storage battery. The UN6HG2 composite packaging may not exceed 8.0
liters in capacity. Completed packages must conform to the Packing
Group III performance level. The maximum authorized gross weight for
the completed package is 37.0 kg (82.0 lbs).
* * * * *
(j) Nickel cadmium batteries containing liquid potassium hydroxide
solution. Nickel-cadmium batteries that contain no more than 10 ml of
liquid potassium hydroxide solution (UN1814) in each battery are not
subject to the requirements of this subchapter under the following
conditions:
(1) Each battery must be sealed in a heat sealed bag, packaged to
prevent short circuits, and placed in the center of an outer packaging
surrounded with a foam-in-place packaging material;
(2) The completed package must meet the Packing Group II
performance level;
(3) The gross weight of the package may not exceed 15.2 kg (33.4
pounds); and
(4) The cumulative amount of potassium hydroxide solution in all of
the batteries in each package may not exceed 4 ounces (0.11 kg).
0
21. In Sec. 173.168, add paragraph (g) to read as follows:
Sec. 173.168 Chemical oxygen generators.
* * * * *
(g) Exceptions. An unapproved chemical oxygen generator with only
one positive means of preventing unintentional actuation of the
generator, and without the required approval number marked on the
outside of the package, may be transported by motor vehicle, railcar,
and cargo vessel only under the following conditions:
(1) Packaging. (i) The one positive means of preventing
unintentional actuation of the generator shall be installed in such a
manner that the percussion primer is so completely protected from its
firing pin that it cannot be physically actuated or the electric firing
circuit is so completely isolated from the electric match that it
cannot be electrically actuated.
(ii) Inner packaging. Except as provided in paragraph (g)(1)(iii)
of this section below, an unapproved chemical oxygen generator, or
unapproved chemical oxygen generator installed in smaller size
equipment such as a PBE shall be packaged in a combination packaging
consisting of a non-combustible inner packaging that fully encloses the
chemical oxygen generator or piece of equipment inside an outer
packaging which meets the requirements in paragraph (d)(1) of this
section.
(iii) Impractical size packaging. If the piece of equipment in
which the unapproved chemical oxygen generator is installed is so large
(e.g., an aircraft seat) as to not be practically able to be fully
enclosed in the packaging prescribed in paragraph (g)(1)(ii) of this
section, then a visible and durable warning tag must be securely
attached to the piece of equipment stating ``THIS ITEM CONTAINS A
CHEMICAL OXYGEN GENERATOR.''
(2) Testing. Each unapproved chemical oxygen generator, without its
packaging, must be capable of withstanding a 1.8 meter drop onto a
rigid, non-resilient, flat and horizontal surface, in the position most
likely to cause damage, with no actuation or loss of contents.
(3) Marking. (i) If the unapproved chemical oxygen generator is
inside a piece of equipment which is sealed or difficult to determine
if an oxygen generator is present, for example--a closed sealed
passenger service unit, then a visible and durable warning sign must be
attached to the piece of equipment stating: ``THIS ITEM CONTAINS A
CHEMICAL OXYGEN GENERATOR''; and
(ii) Each outer package, and overpack if used, must be visibly and
durably marked with the following statement: ``THIS PACKAGE IS NOT
AUTHORIZED FOR TRANSPORTATION ABOARD AIRCRAFT''.
0
22. In Sec. 173.181, revise paragraph (a) and add paragraph (d) to
read as follows:
Sec. 173.181 Pyrophoric materials (liquids).
* * * * *
(a) Authorized cylinders. (1) A specification steel or nickel
cylinder prescribed for any compressed gas, except acetylene, having a
minimum design pressure of 1206 kPa (175 psig).
(2) DOT 3AL cylinders constructed of aluminum alloy 6061-T6 with a
minimum marked service pressure of 1,800 psig and a maximum water
capacity of 49 liters (13 gal) may be used for the transportation of
inorganic pyrophoric liquids (UN3194). Any preheating or heating of the
DOT 3AL cylinder must be limited to a maximum temperature of 79.4
[deg]C (175[emsp14][deg]F).
(3) Cylinders authorized under paragraphs (a)(1) and (a)(2) of this
section equipped with valves must be:
(i) Equipped with steel valve protection caps or collars; or
(ii) Overpacked in a wooden box (4C1, 4C2, 4D or 4F); fiberboard
box (4G), or plastic box (4H1 or 4H2). Cylinders must be secured to
prevent shifting in the box and, when offered for transportation or
transported, must be so loaded that pressure relief devices remain in
the vapor space of the cylinder. (See Sec. 177.838(h) of this
subchapter.)
* * * * *
(d) Combination packagings consisting of the following:
(1) Inner packaging. A 10 liter or 20 liter UN1A1 drum which has
been certified to PG I of subpart M of part 178 of this subchapter.
Each inner drum must--
(i) Have minimum wall thickness of 1.9 mm;
(ii) Have 4 NPT or VCR openings, each with a diameter of 6.3 mm;
(iii) Be fabricated from stainless steel; and
(iv) On the upper head, be fitted with a center opening with a
maximum diameter of 68.3 mm and the opening sealed with a threaded
closure fabricated from 316 stainless steel. No more than two (2) inner
drums may be placed inside the outer drum.
(2) Outer packaging. A UN1A2 drum that has been certified to the PG
I performance level of subpart M of part 178 of this subchapter and a
capacity not to exceed 208 L (55 gal). The drum must have a minimum
wall thickness of 1.0 mm and the top head must be closed with a steel
closing ring with a minimum thickness of 2.4 mm. No more than two (2)
inner drums described in paragraph (d)(1) of this section may be placed
inside the outer drum.
0
23. In Sec. 173.184, add paragraph (c) to read as follows:
Sec. 173.184 Highway or rail fusees.
* * * * *
(c) For transportation by highway, railroad flagging kits are not
subject any other requirements of this subchapter when all of the
following conditions are met:
[[Page 3675]]
(1) The flagging kits may only contain fusees and railroad
torpedoes as follows:
(i) Fusee (rail or highway) (NA1325, Division 4.1, PG II).
(ii) Articles, pyrotechnic (UN0431, Division 1.4G, PG II).
(iii) Signal devices, hand (UN0373, Division 1.4S, PG II).
(iv) Signal devices, hand (UN0191, Division 1.4G, PG II).
(v) Signals, railway track, explosive (UN0193, Division 1.4S, PG
II).
(2) Fusees and railroad torpedoes must be transported in
compartmented metal containers. Each compartment must have a cover with
a latching device. Compartments for railroad torpedoes must be equipped
with a spring-loaded positive locking device. Each compartment may only
contain one type of device.
(3) Each flagging kit may contain a maximum of 36 fusees and 36
railroad torpedoes. No more than six (6) flagging kits may be
transported at one time on any motor vehicle.
(4) Flagging kits may only be transported on railroad motor
vehicles including privately owned motor vehicles under the direct
control of on-duty railroad employees.
(5) The fusees and railroad torpedoes must be kept in the closed
flagging kits whenever they are not being used on the railroad right-
of-way, while the motor vehicle is being driven, or whenever the motor
vehicle is located on other than railroad property.
(6) When left in unattended motor vehicles on non-railroad
property, a flagging kit must be locked inside the motor vehicle, or
stored in a locked compartment on the motor vehicle.
0
24. In Sec. 173.188, add paragraph (a)(3) to read as follows:
Sec. 173.188 White or yellow phosphorus.
* * * * *
(a) * * *
(3)(i) A 115 L (30 gallon) UN1A2 steel drum certified to the PG I
performance level for solids and the PG I or PG II performance level
for liquids and dual marked, at a minimum, as a UN1A2/X400/S (for
solid) and UN1A2 X(or Y)/1.4/150 (for liquids) subject to the following
conditions:
(ii) Enough water must be present in each drum to ensure that the
phosphorous is covered by water at all times during transportation, in
any orientation of the drum;
(iii) Drums must be held and observed for a minimum of 24-hours
before transportation. Any leaking or otherwise unsuitable drums must
be replaced prior to transportation;
(iv) Packages must be destroyed and may not be reused;
(v) The net mass of the material and water, in kilograms, must not
exceed the mass that would be permitted by calculating the volume of
the packaging in liters multiplied by the specific gravity indicated on
the package certification;
(vi) Transportation is by private or contract motor carrier only;
and
(vii) Transportation is authorized from the offeror's location to a
facility where it must be unloaded by the consignee.
* * * * *
0
25. In Sec. 173.193, revise paragraph (b) to read as follows:
Sec. 173.193 Bromoacetone, methyl bromide, chloropicrin and methyl
bromide or methyl chloride mixtures, etc.
* * * * *
(b) Bromoacetone, methyl bromide, chloropicrin and methyl bromide
mixtures, chloropicrin and methyl chloride mixtures, and chloropicrin
mixtures charged with non-flammable, non-liquefied compressed gas must
be packed in Specification 3A, 3AA, 3B, 3C, 3E, 4A, 4B, 4BA, 4BW, or 4C
cylinders having not over 113 kg (250 pounds) water capacity (nominal)
except:
(1) DOT Specification 4BW cylinders containing chloropicrin and
methyl bromide mixtures may not exceed 453 kg (1000 pounds); and
(2) The capacity limit of this paragraph does not apply to
shipments of methyl bromide.
* * * * *
0
26. In Sec. 173.226, add paragraph (f) to read as follows:
Sec. 173.226 Materials poisonous by inhalation, Division 6.1, Packing
Group I, Hazard Zone A.
* * * * *
(f) Liquid hazardous materials in Division 6.1, PG I, Hazard Zone
A, are excepted from the segregation requirements of Sec. Sec. 174.81,
176.83, and 177.848(d) of this subchapter when packaged as follows:
(1) Inner packaging system. The inner packaging system must consist
of three packagings:
(i) A glass, plastic or metal receptacle, with a capacity of not
more than 1 liter (1 quart), securely cushioned with a non-reactive,
absorbent material. The receptacle must have a closure that is held in
place by any means capable of preventing back-off or loosening of the
closure by impact or vibration during transportation.
(ii) The receptacle must be packed within a leak-tight packaging of
metal, with a capacity of not less than 4 liters (1 gallon); and
(iii) The metal packaging must be securely cushioned with a
nonreactive absorbent material and packed in a leak-tight UN 1A2 steel
drum or UN 1H2 plastic drum, with a capacity of not less than 19 liters
(5 gallons).
(2) Outer packaging. The inner packaging system must be placed in a
UN 1A2 steel drum or UN 1H2 plastic drum, with a capacity of not less
than 114 liters (30 gallons). The inner packaging system must be
securely cushioned with a non-reactive, absorbent material. The total
amount of liquid contained in the outer packaging may not exceed 1
liter (1 quart).
(3) Both the inner packaging system and the outer packaging must
conform to the performance test requirements of subpart M of part 178
of this subchapter at the PG I performance level. The inner packaging
system must meet these tests without benefit of the outer packaging.
0
27. In Sec. 173.301, revise paragraphs (f)(1), (f)(2), and (h)(2)(i),
and add paragraph (f)(7) to read as follows:
Sec. 173.301 General requirements for shipment of compressed gases
and other hazardous materials in cylinders, UN pressure receptacles and
spherical pressure vessels.
* * * * *
(f) Pressure relief device systems. (1) Except as provided in
paragraphs (f)(5) through (f)(7) and (j) of this section, and Sec.
171.23(a) of this subchapter, a cylinder filled with a gas and offered
for transportation must be equipped with one or more pressure relief
devices sized and selected as to type, location, and quantity, and
tested in accordance with CGA S-1.1 (compliance with paragraph 9.1.1.1
is not required) and CGA Pamphlet S-7 (IBR, see Sec. 171.7 of this
subchapter). The pressure relief device must be capable of preventing
rupture of the normally filled cylinder when subjected to a fire test
conducted in accordance with CGA C-14 (IBR, see Sec. 171.7 of this
subchapter), or, in the case of an acetylene cylinder, CGA C-12 (IBR,
see Sec. 171.7 of this subchapter).
(2) A pressure relief device, when installed, must be in
communication with the vapor space of a cylinder containing a Division
2.1 (flammable gas) material. This requirement does not apply to DOT
Specification 39 cylinders of 1.2L (75 cubic inches) or less in volume
filled with a Liquefied petroleum gas, Methyl acetylene and Propadiene
mixtures, stabilized, Propylene, Propane or Butane.
* * * * *
(7) A pressure relief device is not required on a DOT Specification
3E cylinder measuring up to 50mm (2 inches) in diameter by 305mm (12
[[Page 3676]]
inches) in length for the following specified gases and maximum weight
limits:
(i) Carbon Dioxide 0.24L (8 oz.)
(ii) Ethane 0.12L (4 oz.)
(iii) Ethylene 0.12L (4 oz.)
(iv) Hydrogen Chloride, anhydrous 0.24L (8 oz.)
(v) Monochlorotrifluoromethane 0.35L (12 oz.)
(vi) Nitrous oxide, 0.24L (8 oz.)
(vii) Vinyl fluoride, stabilized 0.24L (8 oz.)
* * * * *
(h) * * *
(2) * * *
(i) By equipping the cylinder with securely attached metal or
plastic caps of sufficient strength to protect valves from damage
during transportation;
* * * * *
0
28. In Sec. 173.302, revise paragraph (f)(1) to read as follows:
Sec. 173.302 Filling of cylinders with nonliquefied (permanent)
compressed gases or adsorbed gases.
* * * * *
(f) * * *
(1) Only DOT specification 3A, 3AA, 3AL, 3E, 3HT, 39 cylinders, 4E
(filled to less than 200 psig at 21 [deg]C (70 [deg]F), and UN pressure
receptacles ISO 9809-1, ISO 9809-2, ISO 9809-3 and ISO 7866 cylinders
are authorized.
* * * * *
0
29. In Sec. 173.302a:
0
a. Revise paragraphs (a)(1) and (a)(5);
0
b. Add paragraph (a)(6);
0
c. Redesignate paragraphs (c), (d) and (e) as paragraphs (d), (e), and
(f); and
0
d. Add new paragraph (c).
The revisions and additions are to read as follows:
Sec. 173.302a Additional requirements for shipment of nonliquefied
(permanent) compressed gases in specification cylinders.
(a) * * *
(1) DOT 3, 3A, 3AA, 3AL, 3B, 3E, 4B, 4BA, 4BW, and 4E cylinders.
* * * * *
(5) Aluminum cylinders manufactured in conformance with
specifications DOT 39, 3AL and 4E are authorized for oxygen only under
the conditions specified in Sec. 173.302(b).
(6) DOT 4E cylinders- DOT 4E cylinders with a maximum capacity of
43L (11 gal) must have a minimum rating of 240 psig and be filled to no
more than 200 psig at 21 [deg]C (70 [deg]F).
* * * * *
(c) Special filling limits for DOT 3A, 3AX, 3AA, and 3AAX cylinders
containing Division 2.1 gases. Except for transportation by aircraft, a
DOT specification 3A, 3AX, 3AA, and 3AAX cylinder may be filled with
hydrogen and mixtures of hydrogen with helium, argon or nitrogen, to a
pressure 10% in excess of its marked service pressure subject to the
following conditions:
(1) The cylinder must conform to the requirements of paragraph
(b)(2) and (b)(3) of this section;
(2) The cylinder was manufactured after December 31, 1945;
(3) DOT specification 3A and 3AX cylinders are limited to those
having an intermediate manganese composition.
(i) Cylinders manufactured with intermediate manganese steel must
have been normalized, not quench and tempered. Quench and temper
treatment of intermediate steel is not authorized.
(ii) Cylinders manufactured with chrome moly steel must have been
quenched and tempered, not normalized. Use of normalized chrome moly
steel cylinders is not permitted.
(4) Cylinders must be equipped with pressure relief devices as
follows:
(i) Cylinders less than 1.7 m (65 inches) in length must be
equipped with fusible metal backed frangible disc devices;
(ii) Cylinders 1.7 m (65 inches) or greater in length and 24.5 cm
(9.63 inches) in diameter or larger must be equipped with fusible metal
backed frangible disc devices or frangible disc devices. Cylinders with
a diameter of 0.56 m (22 inches) or larger must be equipped with
frangible disc devices.
* * * * *
0
30. In Sec. 173.304, revise paragraph (d) to read as follows:
Sec. 173.304 Filling of cylinders with liquefied compressed gases.
* * * * *
(d) Refrigerant and dispersant gases. Nontoxic and nonflammable
refrigerant or dispersant gases must be offered for transportation in
cylinders prescribed in Sec. 173.304a of this subchapter, or in DOT
2P, 2Q, or 2Q1 containers (Sec. Sec. 178.33, 178.33a, and 178.33d-2 of
this subchapter). DOT 2P, 2Q, and 2Q1 containers must be packed in
strong outer packagings of such design that protect valves from damage
or accidental functioning under conditions incident to transportation.
For DOT 2P and 2Q containers, the pressure inside the containers may
not exceed 87 psia at 21.1[deg]C (70 [deg]F). For 2Q1 containers, the
pressure inside the container may not exceed 210 psig at 55 [deg]C (131
[deg]F). Each completed metal container filled for shipment must be
heated until its contents reach a minimum temperature of 55 [deg]C (131
[deg]F) without evidence of leakage, distortion, or other defect. Each
outer package must be plainly marked ``INSIDE CONTAINERS COMPLY WITH
PRESCRIBED SPECIFICATIONS''.
* * * * *
0
31. In Sec. 173.304a, in the paragraph (a)(2) table, add three new
entries each for Carbon dioxide and Nitrous oxide alphabetically and in
numerical order according to the maximum permitted filling density to
read as follows:
Sec. 173.304a Additional requirements for shipment of liquefied
compressed gases in specification cylinders.
(a) * * *
(2) * * *
------------------------------------------------------------------------
Packaging
marked as shown
in this column
or of the same
type with
higher service
pressure must
Maximum permitted be used, except
Kind of gas filling density (%) (see as provided in
Note 1) Sec. Sec.
173.301(l),
173.301a(e),
and 180.205(a)
(see notes
following
table)
------------------------------------------------------------------------
* * * * * * *
Carbon dioxide (see Notes 4, 70.3 DOT-3A2000, DOT-
7, and 8). 3AA2000, DOT-
3AX2000, DOT-
3AAX2000, DOT-
3T2000.
Carbon dioxide (see Notes 4, 73.2 DOT-3A2265, DOT-
7, and 8). 3AA2265, DOT-
3AX2265, DOT-
3AAX2265, DOT-
3T2265.
Carbon dioxide (see Notes 4, 74.5 DOT-3A2400, DOT-
7, and 8). 3AA2400, DOT-
3AX2400, DOT-
3AAX2400, DOT-
3T2400.
* * * * * * *
Nitrous oxide (see Notes 7, 70.3 DOT-3A2000, DOT-
8, and 11). 3AA2000, DOT-
3AX2000, DOT-
3AAX2000, DOT-
3T2000.
[[Page 3677]]
Nitrous oxide (see Notes 7, 73.2 DOT-3A2265, DOT-
8, and 11). 3AA2265, DOT-
3AX2265, DOT-
3AAX2265, DOT-
3T2265.
Nitrous oxide ( see Notes 7, 74.5 DOT-3A2400, DOT-
8, and 11). 3AA2400, DOT-
3AX2400, DOT-
3AAX2400, DOT-
3T2400.
* * * * * * *
------------------------------------------------------------------------
* * * * *
0
32. In Sec. 173.306:
0
a. Revise paragraphs (a) and (b);
0
b. Add paragraph (e)(2); and
0
c. Revise paragraphs (f) and (k).
0
The revisions and additions read as follows:
Sec. 173.306 Limited quantities of compressed gases.
(a) Limited quantities of compressed gases for which exceptions are
permitted as noted by reference to this section in Sec. 172.101 of
this subchapter are excepted from labeling, except when offered for
transportation or transported by air, and, unless required as a
condition of the exception, specification packaging requirements of
this subchapter when packaged in accordance with the following
paragraphs. For transportation by aircraft, the package must conform to
the applicable requirements of Sec. 173.27 and only packages of
hazardous materials authorized aboard passenger-carrying aircraft may
be transported as a limited quantity. In addition, shipments are not
subject to subpart F (Placarding) of part 172 of this subchapter, to
part 174 of this subchapter except Sec. 174.24, and to part 177 of
this subchapter except Sec. 177.817. Except as otherwise provided in
this section, each package may not exceed 30 kg (66 lbs.) gross weight.
(1) When in containers of not more than 4 fluid ounces capacity
(7.22 cubic inches or less) except cigarette lighters. Additional
exceptions for certain compressed gases in limited quantities and the
ORM-D hazard class are provided in paragraph (i) of this section.
(2) When in refillable metal containers filled with a material that
is not classed as a hazardous material to not more than 90% of capacity
at 21.1 [deg]C (70 [deg]F) and then charged with nonflammable,
nonliquefied gas. Each container must be tested to three times the
pressure at 21.1 [deg]C (70 [deg]F) and, when refilled, be retested to
three times the pressure of the gas at 21.1 [deg]C (70 [deg]F). Also,
one of the following conditions must be met:
(i) The container is not over 0.95 L (1 quart) capacity and charged
to not more than 170 psig (1172.1 kPa) at 21.1 [deg]C (70 [deg]F), and
must be packed in a strong outer packaging; or
(ii) The container is not over 114 L (30 gallons) capacity and
charged to not more than 75 psig (517.1 kPa) at 21.1 [deg]C (70
[deg]F).
(3) When in a metal aerosol container (see Sec. 171.8 of this
subchapter for the definition of aerosol). Authorized containers
include non-specification, DOT 2P (Sec. 178.33 of this subchapter),
DOT 2Q (Sec. 178.33a of this subchapter), or DOT 2Q1 (Sec. 178.33(d)
of this subchapter) design, provided the following conditions are met.
Additional exceptions for aerosol containers conforming to this
paragraph (a)(3) are provided in paragraph (i) of this section.
(i) Capacity. The capacity of the container must not exceed 1 L
(61.0 cubic inches).
(ii) General pressure conditions. The authorized metal aerosol
containers and associated pressure limitations are provided in the
following table. Pressure inside the container may not exceed 180 psig
at 54.4 [deg]C (130 [deg]F) except as may be authorized by variations
of a DOT specification container type. In any event, the metal
container must be capable of withstanding without bursting a pressure
of at least one and one-half times the equilibrium pressure of the
contents at 54.4 [deg]C (130 [deg]F).
Authorized Metal Aerosol Containers
----------------------------------------------------------------------------------------------------------------
If the gauge pressure (psig) at 54.4
[deg]C (130 [deg]F) is . . . Authorized container
----------------------------------------------------------------------------------------------------------------
140 or less......................... Non-DOT specification, DOT 2P, DOT 2Q, DOT 2Q1.
Greater than 140 but not exceeding DOT 2P, DOT 2Q, DOT 2Q1.
160.
Greater than 160 but not exceeding DOT 2Q, DOT 2Q1.
180.
Not to exceed 210................... DOT 2Q1 (Non-flammable only).
----------------------------------------------------------------------------------------------------------------
(iii) Liquid fill. The liquid content of the material and gas must
not completely fill the container at 54.4 [deg]C (130 [deg]F).
(iv) Outer packaging. The containers must be packed in strong outer
packagings.
(v) Pressure testing. Except as otherwise provided in this
paragraph, each container, after it is filled, must be subjected to a
test performed in a hot water bath; the temperature of the bath and the
duration of the test must be such that the internal pressure reaches
that which would be reached at 55 [deg]C (131 [deg]F), or 50 [deg]C
(122 [deg]F) if the liquid phase does not exceed 95% of the capacity of
the container at 50 [deg]C (122 [deg]F)). If the contents are sensitive
to heat, the temperature of the bath must be set at between 20 [deg]C
(68 [deg]F) and 30 [deg]C (86 [deg]F) but, in addition, one container
in 2,000 must be tested at the higher temperature. No leakage or
permanent deformation of a container may occur. However, instead of
this standard water bath test, container(s) may be tested using one of
the following methods subject to certain conditions--
(A) Alternative water bath test. (1) One filled container in a lot
of 2,000 must be subjected to a test performed in a hot water bath; the
temperature of the bath and the duration of the test must be such that
the internal pressure reaches that which would be reached at 55 [deg]C
(131 [deg]F). If the container shows evidence of leakage or permanent
[[Page 3678]]
deformation, the lot of 2,000 containers must be rejected;
(2) A second filled container in the lot of 2,000 must be weighed
and compared to the weight specification for the containers as
documented in the operating procedures for the weight test. Failure of
the container to meet the weight specification is evidence of leakage
or overfilling and the lot of 2,000 must be rejected;
(3) The remainder of the containers in the lot of 2,000 must be
visually inspected (e.g, examination of the seams). Containers showing
evidence of leakage or overfilling must not be transported; and
(4) Each person employing this test must maintain a copy of the
operating procedures (or an electronic file thereof) that is accessible
at, or through, its principal place of business and must make the
procedures available upon request, at a reasonable time and location,
to an authorized official of the Department.
(B) Automated pressure test. Each person employing an automated
process for pressure testing of filled containers must develop
procedures for implementation of the test. Each person must maintain a
copy of the procedures (or an electronic file thereof) that is
accessible at, or through, its principal place of business and must
make the procedures available upon request, at a reasonable time and
location, to an authorized official of the Department. The procedures
must, at a minimum, include instruction on the following:
(1) Pressure specifications. Each person must specify pressure
standard(s) (e.g. a pressure limit or range) for a container respective
of the design and/or contents. Each container, after it is filled, must
be pressure checked and compared to the standards. For a pressure
limit, any container exceeding the pressure limit must be rejected. For
a pressure range, any container outside of the set range must be
rejected. The instruments used to determine the pressure must be
properly calibrated before a production run to an accuracy of +/- or
better; and
(2) Periodic inspection. At designated intervals, a randomly
selected container must be inspected for proper closure and
verification of filling pressure. If a container shows signs of
improper closure or over-filling, five (5) additional randomly selected
containers must be inspected. If any of the additional containers show
signs of improper closure or over-filling, all containers produced
since the last inspection must be rejected.
(C) Weight test. Each person employing a weight test of filled
containers must develop procedures for implementation of the test. Each
person must maintain a copy of the procedures (or an electronic file
thereof) that is accessible at, or through, its principal place of
business and must make the procedures available upon request, at a
reasonable time and location, to an authorized official of the
Department. The procedures must, at a minimum, include instruction on
the following:
(1) Weight specifications. Each person must specify target weight
specifications for a particular container. Each container, after it is
filled, must be weighed and compared to the target weight specification
for the container. Any container outside the target weight
specification is an indication of leakage or overfilling and must be
rejected. The instruments used to determine the weight must be properly
calibrated before a testing run and be sufficiently sensitive to
measure within 0.10 g of the true weight of the container;
(2) Heat testing and pressure limits. One container out of each lot
of successfully filled containers must be heat tested by raising the
internal pressure until it reaches that which would be reached at 55
[deg]C (131 [deg]F). The lot size should be no greater than 2,000. If
the pressure in the container exceeds the maximum pressure allowed for
the container type or if the container shows signs of leakage or
permanent deformation, the lot must be rejected. Alternatively, five
(5) additional randomly selected containers from the lot may be tested
to qualify the lot but if any of the five containers fail the test, the
entire lot must be rejected;
(3) Periodic inspection. At intervals of not more than 10 minutes,
a randomly selected container must be inspected for proper closure and
verification of filling pressure. If a container shows signs of
improper closure or over-filling, five (5) additional randomly selected
containers must be inspected. If any of the additional containers show
signs of improper closure or over-filling, all containers produced
since the last inspection must be rejected; and
(4) Visual inspection. Each container must be visually inspected
prior to being packed. Any container showing signs of leakage or
permanent deformation must be rejected.
(D) Leakage test. (1) Pressure and leak testing before filling.
Each empty container must be subjected to a pressure equal to or in
excess of the maximum expected in the filled containers at 55 [deg]C
(131 [deg]F) or 50 [deg]C (122 [deg]F) if the liquid phase does not
exceed 95% of the capacity of the container at 50 [deg]C (122 [deg]F).
This must be at least two-thirds of the design pressure of the
container. If any container shows evidence of leakage at a rate equal
to or greater than 3.3 x 10-2 mbar L/s at the test pressure,
distortion or other defect, it must be rejected; and
(2) Testing after filling. The person filling each container must
ensure that the crimping equipment is set appropriately and the
specified propellant is used before filling a container. Once filled,
each container must be weighed and leak tested. The leak detection
equipment must be sufficiently sensitive to detect at least a leak rate
of 2.0 x 10-3 mbar L/s at 20 [deg]C (68 [deg]F). Any filled
container which shows evidence of leakage, deformation, or overfilling
must be rejected.
(vi) Each outer packaging must be marked ``INSIDE CONTAINERS COMPLY
WITH PRESCRIBED REGULATIONS.''
(4) Gas samples must be transported under the following conditions:
(i) A gas sample may only be transported as non-pressurized gas
when its pressure corresponding to ambient atmospheric pressure in the
container is not more than 105 kPa absolute (15.22 psia).
(ii) Non-pressurized gases, toxic (or toxic and flammable) must be
packed in hermetically sealed glass or metal inner packagings of not
more than one L (0.3 gallons) overpacked in a strong outer packaging.
(iii) Non-pressurized gases, flammable must be packed in
hermetically sealed glass or metal inner packagings of not more than 5
L (1.3 gallons) and overpacked in a strong outer packaging.
(5) For limited quantities of Division 2.2 gases with no subsidiary
risk, when in a non-DOT specification or a specification DOT 2S (Sec.
178.33b of this subchapter) plastic aerosol container (see Sec. 171.8
of this subchapter for the definition of aerosol) provided all of the
following conditions are met. Additional exceptions for aerosols
conforming to this paragraph (a)(5) are provided in paragraph (i) of
this section.
(i) Capacity. The capacity of the container must not exceed 1 L
(61.0 cubic inches).
(ii) General pressure conditions. Authorized plastic aerosol
containers and associated pressure limitations are provided in the
following table. The pressure in the container must not exceed 160 psig
at 54.4 [deg]C (130 [deg]F). The container must be capable of
withstanding without bursting a pressure of at least one and one-half
times the equilibrium pressure of the contents at 54.4 [deg]C (130
[deg]F).
[[Page 3679]]
Authorized Plastic Aerosol Containers
----------------------------------------------------------------------------------------------------------------
If the gauge pressure (psig)
at 55 [deg]C (131 [deg]F) is Authorized plastic container
. . .
----------------------------------------------------------------------------------------------------------------
Less than 140................ Non-DOT specification, DOT 2S.
140 or greater but not DOT 2S.
exceeding 160.
----------------------------------------------------------------------------------------------------------------
(iii) Liquid fill. Liquid content of the material and gas must not
completely fill the container at 54.4 [deg]C (130 [deg]F).
(iv) Outer packaging. The containers must be packed in strong outer
packagings.
(v) Pressure testing. Except as provided in paragraph (a)(5)(vi) of
this section, each container must be subjected to a test performed in a
hot water bath. The temperature of the bath and the duration of the
test must be such that the internal pressure reaches that which would
be reached at 55 [deg]C (131 [deg]F) or 50 [deg]C (122 [deg]F) if the
liquid phase does not exceed 95% of the capacity of the container at 50
[deg]C (122 [deg]F). If the contents are sensitive to heat, or if the
container is made of plastic material which softens at this test
temperature, the temperature of the bath must be set at between 20
[deg]C (68 [deg]F) and 30 [deg]C (86 [deg]F) but, in addition, one
container in 2,000 must be tested at the higher temperature. No leakage
or permanent deformation of a container is permitted except that a
plastic container may be deformed through softening provided that it
does not leak.
(vi) Leakage test. As an alternative to the hot water bath test in
paragraph (a)(5)(v) of this section, testing may be performed as
follows:
(A) Pressure and leak testing before filling. Each empty container
must be subjected to a pressure equal to or in excess of the maximum
expected in the filled containers at 55 [deg]C (131 [deg]F) or 50
[deg]C (122 [deg]F) if the liquid phase does not exceed 95% of the
capacity of the container at 50 [deg]C (122 [deg]F). This must be at
least two-thirds of the design pressure of the container. If any
container shows evidence of leakage at a rate equal to or greater than
3.3 x 10-2 mbar L/s at the test pressure, distortion or
other defect, it must be rejected; and
(B) Testing after filling. Prior to filling, the filler must ensure
that the crimping equipment is set appropriately and the specified
propellant is used before filling the container. Once filled, each
container must be weighed and leak tested. The leak detection equipment
must be sufficiently sensitive to detect at least a leak rate of 2.0 x
10-3 mbar L/s at 20 [deg]C (68 [deg]F). Any filled container
that shows evidence of leakage, deformation, or excessive weight must
be rejected.
(vii) Each outer packaging must be marked ``INSIDE CONTAINERS
COMPLY WITH PRESCRIBED REGULATIONS.''
(b) Exceptions for foodstuffs, soap, biologicals, electronic tubes,
and audible fire alarm systems. Limited quantities of compressed gases
(except Division 2.3 gases) for which exceptions are provided as
indicated by reference to this section in Sec. 172.101 of this
subchapter, when in conformance with one of the following paragraphs,
are excepted from labeling, except when offered for transportation or
transported by aircraft, and the specification packaging requirements
of this subchapter. For transportation by aircraft, the package must
conform to the applicable requirements of Sec. 173.27 and only
packages of hazardous materials authorized aboard passenger-carrying
aircraft may be transported as a limited quantity. In addition,
shipments are not subject to subpart F (Placarding) of part 172 of this
subchapter, to part 174 of this subchapter, except Sec. 174.24, and to
part 177 of this subchapter, except Sec. 177.817. Additional
exceptions for certain compressed gases in limited quantities and the
ORM-D hazard class are provided in paragraph (i) of this section.
(1) Foodstuffs or soaps with soluble or emulsified compressed gas
are authorized in non-refillable metal or plastic containers not to
exceed 1 L (61.0 cubic inches) capacity provided the pressure in each
container does not exceed 140 psig at 54.4 [deg]C (130 [deg]F) unless
authorized by variation of a container type. For pressures ranging from
greater than 140 psig to 160 psig, a variation DOT 2P1 or DOT 2Q2
(Sec. Sec. 178.33(c) and (d) of this subchapter, respectively)
container must be used. However, the pressure of the contents in the
container may not be greater than 150 psig at 23.9 [deg]C (75 [deg]F).
Plastic containers may only contain Division 2.2 non-flammable soluble
or emulsified compressed gas. Metal or plastic containers must be
capable of withstanding, without bursting, a pressure of at least one
and one-half times the equilibrium pressure of the contents at 54.4
[deg]C (130 [deg]F).
Authorized Aerosol Containers for Foodstuffs and Soaps
----------------------------------------------------------------------------------------------------------------
If the gauge pressure (psig)
at 54.4 [deg]C (130 [deg]F) Authorized container
is . . .
----------------------------------------------------------------------------------------------------------------
Not exceeding 140............ Non-DOT specification, DOT 2P, DOT 2P1, DOT 2Q, DOT 2Q2.
Greater than 140 but not DOT 2P, DOT 2P1, DOT 2Q, DOT 2Q2.
exceeding 160.
Greater than 160 but not DOT 2Q, DOT 2Q2.
exceeding 180.
----------------------------------------------------------------------------------------------------------------
(i) Containers must be packed in strong outer packagings.
(ii) Liquid content of the material and the gas must not completely
fill the container at 55 [deg]C (131 [deg]F).
(iii) Each outer packaging must be marked ``INSIDE CONTAINERS
COMPLY WITH PRESCRIBED REGULATIONS.''
(2) Cream in refillable metal or plastic containers with soluble or
emulsified compressed gas. Plastic containers must only contain
Division 2.2 non-flammable soluble or emulsified compressed gas.
Containers must be of such design that they will hold pressure without
permanent deformation up to 375 psig and must be equipped with a device
designed so as to release pressure without bursting of the container or
dangerous projection of its parts at higher pressures. This exception
applies to shipments offered for transportation by refrigerated motor
vehicles only.
(3) Nonrefillable metal or plastic containers charged with a
Division 6.1 PG III or nonflammable solution containing biological
products or a medical preparation that could be deteriorated by heat,
and compressed gas or gases. Plastic containers may only contain 2.2
non-flammable soluble or emulsified compressed gas. The
[[Page 3680]]
capacity of each container may not exceed 35 cubic inches (19.3 fluid
ounces). The pressure in the container may not exceed 140 psig at 54.4
[deg]C (130 [deg]F), and the liquid content of the product and gas must
not completely fill the containers at 54.4 [deg]C (130 [deg]F). One
completed container out of each lot of 500 or less, filled for
shipment, must be heated, until the pressure in the container is
equivalent to equilibrium pressure of the contents at 54.4 [deg]C (130
[deg]F). There must be no evidence of leakage, distortion, or other
defect. The container must be packed in strong outer packagings.
(4) Electronic tubes, each having a volume of not more than 30
cubic inches and charged with gas to a pressure of not more than 35
psig and packed in strong outer packagings are authorized.
(5) Audible fire alarm systems powered by a compressed gas
contained in an inside metal container when shipped are authorized
under the following conditions:
(i) Each inside container must have contents that are not
flammable, poisonous, or corrosive as defined under this part,
(ii) Each inside container may not have a capacity exceeding 35
cubic inches (19.3 fluid ounces),
(iii) Each inside container may not have a pressure exceeding 70
psig at 21.1 [deg]C (70 [deg]F) and the liquid portion of the gas may
not completely fill the inside container at 54.4 [deg]C (130 [deg]F),
and
(iv) Each nonrefillable inside container must be designed and
fabricated with a burst pressure of not less than four times its
charged pressure at 54.4 [deg]C (130 [deg]F). Each refillable inside
container must be designed and fabricated with a burst pressure of not
less than five times its charged pressure at 54.4 [deg]C (130 [deg]F).
* * * * *
(e) * * *
(2) Used refrigerating machines. (i) Packaging. Reconditioned
(used) refrigerating machines (UN 2857, Div. 2.2) may be excepted from
the marking requirements of Sec. 172.302(c) of this subchapter and
transported by motor vehicle when they conform to the requirements
prescribed in Sec. 173.306(e)(1), are secured or permanently attached
to the motor vehicle, and are:
(A) Permanently affixed to a steel base structure,
(B) Permanently affixed to a trailer, or
(C) Manufactured with a rigid internal structure designed for
transportation and stacking conditions such that they do not leak and
do not deteriorate, distort, or become damaged in a manner that could
adversely affect their safety or reduce their strength in
transportation, cause instability in stacks of refrigerating machines,
or cause damage to these machines in a way that is likely to reduce
safety in transportation.
(ii) Testing. Used refrigerating machines returned from their
rental locations must be transported back to an authorized original
equipment manufacturer service facility and undergo maintenance, repair
and/or replacement that renders these machines operational at the same
level as that of new refrigerating machines, and must undergo a leak
test by a certified technician, prior to re-shipment.
(f) Accumulators (Articles, pressurized pneumatic or hydraulic
containing non-flammable gas). The following applies to accumulators,
which are hydraulic accumulators containing nonliquefied, nonflammable
gas, and nonflammable liquids or pneumatic accumulators containing
nonliquefied, nonflammable gas, fabricated from materials which will
not fragment upon rupture.
(1) Accumulators installed in motor vehicles, construction
equipment, and assembled machinery and designed and fabricated with a
burst pressure of not less than five times their charged pressure at 70
[deg]F, when shipped, are not subject to the requirements of this
subchapter.
(2) Accumulators charged with limited quantities of compressed gas
to not more than 200 psig at 70 [deg]F are excepted from labeling
(except when offered for transportation by air) and the specification
packaging requirements of this subchapter when shipped under the
following conditions. In addition, shipments are not subject to subpart
F (placarding) of part 172 of this subchapter, to part 174 of this
subchapter except Sec. 174.24 and to part 177 of this subchapter
except Sec. 177.817.
(i) Each accumulator must be shipped as an inside packaging;
(ii) Each accumulator may not have a gas space exceeding 2,500
cubic inches under stored pressure; and
(iii) Each accumulator must be tested, without evidence of failure
or damage, to at least three times its charged pressure of 70 [deg]F,
but not less than 120 psi before initial shipment and before each
refilling and reshipment.
(3) Accumulators with a charging pressure exceeding 200 psig at 70
[deg]F and in compliance with the requirements stated in paragraph
(f)(2) of this section, as applicable, are excepted from labeling
(except when offered for transportation by air) and the specification
packaging requirements of this subchapter when shipped under the
following conditions:
(i) Each accumulator must be designed and fabricated with a burst
pressure of not less than five (5) times its charged pressure at 70
[deg]F when shipped;
(ii) For an accumulator with a gas space not to exceed 100 cubic
inches, it must be designed and fabricated with a burst pressure of not
less than five (5) times its charged pressure at 70 [deg]F. Out of each
lot not to exceed 1,000 successively produced accumulators per day of
the same type, accumulators must be tested, in lieu of the testing of
paragraph (f)(2)(iii) of this section, as follows:
(A) One (1) accumulator must be tested to the minimum design burst
pressure;
(B) Two (2) accumulators, one at the beginning of production and
one at the end must be tested to at least two and a half times the
charge pressure without evidence of leakage or distortion;
(C) If accumulators fail either test, an additional four (4) sets
of accumulators from the lot may be tested. If any additional
accumulators fail, the lot must be rejected;
(iii) For an accumulator with a gas space not to exceed 30 cubic
inches, it must be designed and fabricated with a burst pressure of not
less than four (4) times its charged pressure at 70 [deg]F. Out of each
lot not to exceed 1,000 successively produced accumulators per day of
the same type, accumulators must be tested, in lieu of the testing of
paragraph (f)(2)(iii) of this section, as follows:
(A) One (1) accumulator must be tested to the minimum design burst
pressure;
(B) Two (2) accumulators, one at the beginning of production and
one at the end must be tested to at least two and a half times the
charge pressure without evidence of leakage or distortion;
(C) If accumulators fail either test, an additional four (4) sets
of accumulators from the lot may be tested. If any additional
accumulators fail, the lot must be rejected;
(iv) Accumulators must be packaged in strong outer packaging.
(4) Accumulators intended to function as shock absorbers, struts,
gas springs, pneumatic springs or other impact or energy-absorbing
devices are not subject to the requirements of this subchapter provided
each:
(i) Has a gas space capacity not exceeding 1.6 L and a charge
pressure not exceeding 280 bar, where the product of the capacity
expressed in
[[Page 3681]]
liters and charge pressure expressed in bars does not exceed 80 (for
example, 0.5 L gas space and 160 bar charge pressure);
(ii) Has a minimum burst pressure of 4 times the charge pressure at
20 [deg]C for products not exceeding 0.5 L gas space capacity and 5
times the charge pressure for products greater than 0.5 L gas space
capacity;
(iii) Design type has been subjected to a fire test demonstrating
that the article relieves its pressure by means of a fire degradable
seal or other pressure relief device, such that the article will not
fragment and that the article does not rocket; and
(iv) Accumulators must be manufactured under a written quality
assurance program which monitors parameters controlling burst strength,
burst mode and performance in a fire situation as specified in
paragraphs (f)(4)(i) through (f)(4)(iii) of this section. A copy of the
quality assurance program must be maintained at each facility at which
the accumulators are manufactured.
(5) Accumulators not conforming to the provisions of paragraphs
(f)(1) through (f)(4) of this section may only be transported subject
to the approval of the Associate Administrator.
* * * * *
(k) Aerosols for recycling or disposal. Aerosols (as defined in
Sec. 171.8 of this subchapter) intended for recycling or disposal may
be transported under the following conditions:
(1) Aerosols conforming to paragraph (a)(3), (a)(5), (b)(1),
(b)(2), or (b)(3) of this section are not subject to the 30 kg (66
pounds) gross weight limitation when transported by motor vehicle for
purposes of recycling or disposal under the following conditions:
(i) The aerosols must be packaged in a strong outer packaging. The
strong outer packaging and its contents must not exceed a gross weight
of 500 kg (1,100 pounds);
(ii) Each aerosol must be secured with a cap to protect the valve
stem or the valve stem must be removed; and
(iii) The packaging must be offered for transportation or
transported by--
(A) Private or contract motor carrier; or
(B) Common carrier in a motor vehicle under exclusive use for such
service.
(2) Aerosols intended to conform to paragraphs (a)(3) or (a)(5) of
this section at the time of filling but are leaking, have been
improperly filled, or otherwise no longer conform to paragraphs (a)(3)
or (a)(5) of this section may be offered for transportation and
transported for disposal or recycling under the conditions provided in
this paragraph (k)(2). Such aerosols are not eligible for the
exceptions provided in paragraphs (a) and (i) of this section except
for subpart F (Placarding) of part 172 of this subchapter.
(i) Packaging. (A) The aerosols must be packaged in a metal or
plastic removable head UN 1A2, 1B2, 1N2 or 1H2 drum tested and marked
to the PG II performance level or higher for liquids;
(B) Each drum must be provided, when necessary, with sufficient
cushioning and absorption material to prevent excessive shifting of the
aerosols and to eliminate the presence of any free liquid at the time
the drum is closed. All cushioning and absorbent material used in the
drum must be compatible with the hazardous material; and
(C) The pressure inside each completed drum, at any time during
transportation, may not exceed the design test pressure marked on the
drum.
(ii) Hazard communication. (A) Notwithstanding the marking
requirements for non-bulk packages in Sec. 172.301 of this subchapter,
each drum must be marked ``AEROSOL SALVAGE'' or ``AEROSOL SALVAGE
DRUM'' in association with the required label(s); and
(B) The overpack marking requirements of Sec. 173.25 of this
subchapter do not apply.
(3) Modal restrictions. The completed drums must be offered for
transportation and transported by private or contract carrier by
highway or rail. Vessel and air transportation are not authorized.
* * * * *
0
33. In Sec. 173.315, paragraph (a)(2) table, the entry ``Division 2.2
materials not specifically provided for in this table'' is revised, and
a note 28 is added to the end of the table. The revision and addition
read as follows:
Sec. 173.315 Compressed gases in cargo tanks and portable tanks.
(a) * * *
(2) * * *
----------------------------------------------------------------------------------------------------------------
Maximum permitted filling density Specification container required
-------------------------------------------------------------------------------
Kind of gas Percent by volume
Percent by weight (see par. (f) of Type (see Note 2) Minimum design
(see Note 1) this section) pressure (psig)
----------------------------------------------------------------------------------------------------------------
* * * * * * *
Division 2.2, materials not See par. (c) of See Note 7........ DOT-51, MC-330, MC- See Notes 19 and
specifically provided for in this section. 331. 28.
this table.
* * * * * * *
----------------------------------------------------------------------------------------------------------------
* * * * *
Note 28: For UN1080, Sulfur hexafluoride, a non-specification cargo
tank that otherwise conforms to a DOT Specification MC 331 cargo tank
except for design pressure and capacity is authorized. Design pressure
may not exceed 600 psig. The water capacity range for each tank is 15
to 500 gallons.
* * * * *
0
34. In Sec. 173.319, revise paragraph (d)(2) table to read as follows:
Sec. 173.319 Cryogenic liquids in tank cars.
* * * * *
(d) * * *
(2) * * *
[[Page 3682]]
Pressure Control Valve Setting or Relief Valve Setting
----------------------------------------------------------------------------------------------------------------
Maximum permitted filling density (percent by weight)
Maximum start-to-discharge -------------------------------------------------------------------------------
pressure (psig) Ethylene Ethylene Ethylene Hydrogen
----------------------------------------------------------------------------------------------------------------
17.............................. .................. .................. .................. 6.60.
45.............................. 52.8..............
75.............................. .................. 51.1.............. 51.1..............
Maximum pressure when offered 10 psig........... 20 psig........... 20 psig...........
for transportation.
Design service temperature...... Minus 260 [deg]F.. Minus 260 [deg]F.. Minus 155 [deg]F.. Minus 423 [deg]F.
Specification (see Sec. 113D60W, 113C60W.. 113C120W.......... 113D120W.......... 113A175W, 113A60W.
180.507(b)(3) of this
subchapter).
----------------------------------------------------------------------------------------------------------------
* * * * *
PART 174--CARRIAGE BY RAIL
0
35. The authority citation for part 174 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; 49 CFR 1.81 and 1.97.
0
36. In Sec. 174.67, revise paragraph (g) to read as follows:
Sec. 174.67 Tank car unloading.
* * * * *
(g) The valve cap, or the reducer when a large outlet is to be
used, must be removed with a suitable wrench after the set screws are
loosened and a pail must be placed in position to catch any liquid that
may be in the outlet chamber. If the valve cap or reducer does not
unscrew easily, it may be tapped lightly with a mallet or wooden block
in an upward direction. If leakage shows upon starting the removal, the
cap or reducer may not be entirely unscrewed. Sufficient threads must
be left engaged and sufficient time allowed to permit the controlled
escape of any accumulation of liquid in the outlet chamber. If the
leakage stops or the rate of leakage diminishes materially, the cap or
reducer may be entirely removed. If the initial rate of leakage
continues, further efforts must be made to seat the outlet valve (see
paragraph (f) of this section). If this fails, the cap or reducer must
be screwed up tight and the tank must be unloaded through the dome. If
upon removal of the outlet cap the outlet chamber is found to be
blocked with frozen liquid or any other matter, the cap must be
replaced immediately and a careful examination must be made to
determine whether the outlet casting has been cracked. If the
obstruction is not frozen liquid, the car must be unloaded through the
dome. If the obstruction is frozen liquid and no crack has been found
in the outlet casting, the car may, if circumstances require it, be
unloaded from the bottom by removing the cap and attaching unloading
connections immediately. Before opening the valve inside the tank car
with a frozen liquid blockage:
(1) Steam must be applied to the outside of the outlet casting or
the outlet casting must be wrapped with burlap or other rags and hot
water applied to the wrapped casting to melt the frozen liquid; or
(2) For combustible liquid or Class 3 liquid petroleum distillate
fuels, the blockage may be cleared by attaching a fitting to the outlet
line and applying nitrogen at a pressure not to exceed 100 psig.
* * * * *
PART 176--CARRIAGE BY VESSEL
0
37. The authority citation for part 176 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; 49 CFR 1.81 and 1.97.
0
38. Revise Sec. 176.90 to read as follows:
Sec. 176.90 Private automobiles.
(a) Class 1 (explosive) material. A private automobile which is
carrying any Class 1 (explosive) material (except permitted fireworks
or small arms ammunition) may not be transported on a passenger-
carrying ferry vessel unless the Class 1 (explosive) material conforms
to the packaging, labeling, marking, and certification requirements of
this subchapter. Permitted fireworks and small arms ammunition may be
carried without the required packaging, labeling, marking, or
certification if they are in tight containers.
(b) Engines, gasoline, or liquefied petroleum gas. Engines,
internal combustion, flammable gas powered or flammable liquid powered,
including when fitted in machinery or vehicles (i.e. motor vehicles,
recreational vehicles, campers, trailers), vehicle flammable liquid or
flammable gas powered, gasoline, and petroleum gases, liquefied or
liquefied petroleum gas when included as part of a motor home,
recreational vehicle, camper, or trailer; are excepted from the
requirements of this subchapter if the following conditions are met:
(1) Any container showing deterioration which might affect its
integrity must not be allowed on board the vessel. A visual inspection
by a responsible member of the crew must be made of each cylinder of
liquefied petroleum gas before it may be allowed aboard the vessel. A
cylinder that has a crack or leak, is bulged, has a defective valve or
a leaking or defective pressure relief device, or bears evidence of
physical abuse, fire or heat damage, or detrimental rusting or
corrosion, may not offered for transportation on board the vessel.
Leaking or damaged containers of gasoline may not be offered for
transportation on board the vessel.
(2) Motor vehicles may be stowed in the same hold or compartment or
on the vehicle deck of passenger vessels with cylinders of liquefied
petroleum gas when the cylinders are securely attached to recreational
vehicles, such as campers or trailers.
(3) Extra containers of gasoline (including camp stove or lantern
fuel) and portable cylinders of liquefied petroleum gas (including
cylinders for camping equipment) not securely attached to recreational
vehicles must be stowed in the vessel's paint locker. Containers must
be securely closed.
(4) All liquefied petroleum gas cylinders must be secured by
closing the shut-off valves prior to the recreational vehicles being
loaded on the vessels. The owner or operator of each recreational
vehicle must be directed to close all operating valves within the
vehicles.
(5) ``No smoking'' signs must be posted on the vehicle decks and,
if used for storage of hazardous materials; in close proximity to the
vessel's paint locker.
(6) An hourly patrol of the vehicle decks must be made by a
crewmember. Any unusual or dangerous situation must be reported to the
vessel's master.
[[Page 3683]]
(7) Passengers may be allowed on the vehicle decks during the
voyage and are subject to the control of the crew personnel conducting
the continuous vehicle deck patrol.
(8) Each person responsible for performing a function authorized by
this section must be trained in accordance with subpart H of part 172
of this subchapter and on the requirements of this section.
(9) Shipments made under this paragraph are subject to the Incident
Reporting requirements prescribed in Sec. Sec. 171.15 and 171.16 of
this subchapter.
0
39. In Sec. 176.800, revise paragraph (a) to read as follows:
Sec. 176.800 General stowage requirements.
(a) Each package required to have a Class 8 (corrosive) label
thereon being transported on a vessel must be stowed clear of living
quarters, and away from foodstuffs and cargo of an organic nature. For
the purposes of this section, food ingredients intended for human
consumption (ingredients) that are Class 8 (corrosive) materials are
not considered to be incompatible with other food ingredients if the
intended use of those ingredients is for the manufacture of food, or
food ingredients containing those food ingredients (or like
ingredients), with or without other ingredients.
* * * * *
PART 177--CARRIAGE BY PUBLIC HIGHWAY
0
40. The authority citation for part 177 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; sec. 112 of Pub. L. 103-311, 108
Stat. 1673, 1676 (1994); sec. 32509 of Pub. L. 112-141, 126 Stat.
405, 805 (2012); 49 CFR 1.81 and 1.97.
0
41. In Sec. 177.834, revise paragraphs (i)(3), (i)(4), and (l)(2)(i),
and remove and reserve paragraph (l)(2)(ii) to read as follows:
Sec. 177.834 General requirements.
* * * * *
(i) * * *
(3) A qualified person ``attends'' the loading or unloading of a
cargo tank only if, throughout the process:
(i) Except for unloading operations subject to Sec. Sec.
177.837(d), 177.840(p), and 177.840(q), the qualified person is within
7.62 m (25 feet) of the cargo tank. The qualified person attending the
unloading of a cargo tank must be alert and have an unobstructed view
of the cargo tank and delivery hose to the maximum extent practicable
during the unloading operation;
(ii) The qualified person observes all loading or unloading
operations by means of video cameras and monitors or instrumentation
and signaling systems such as sensors, alarms, and electronic
surveillance equipment located at a remote control station, and the
loading or unloading system is equipped as follows:
(A) For a video monitoring system used to meet the attendance
requirement, the camera must be mounted so as to provide an
unobstructed view of all equipment involved in the loading or unloading
operations, including all valves, hoses, domes, and pressure relief
devices.
(B) For an instrumentation and signaling system used to meet the
attendance requirement, the system must provide a surveillance
capability at least equal to that of a human observer.
(C) Upon loss of video monitoring capability or instrumentation and
signaling systems, loading or unloading operations must be immediately
terminated.
(D) Shut-off valves operable from the remote control station must
be provided.
(E) In the event of a remote system failure, a qualified person
must immediately resume attending the loading or unloading of the cargo
tank as provided in paragraph (i)(3)(i) of this section.
(F) A containment area must be provided capable of holding the
contents of as many cargo tank motor vehicles as might be loaded at any
single time.
(G) A qualified person must personally conduct a visual inspection
of each cargo tank motor vehicle after it is loaded, prior to
departure, for any damage that may have occurred during loading.
(iii) Hoses used in the loading or unloading operations are
equipped with cable-connected wedges, plungers, or flapper valves
located at each end of the hose, able to stop the flow of product from
both the source and the receiving tank within one second without human
intervention in the event of a hose rupture, disconnection, or
separation.
(A) Prior to each use, each hose must be inspected to ensure that
it is of sound quality, without defects detectable through visual
observation; and
(B) The loading or unloading operations must be physically
inspected by a qualified person at least once every sixty (60) minutes.
(4) A person is ``qualified'' if he has been made aware of the
nature of the hazardous material which is to be loaded or unloaded, has
been instructed on the procedures to be followed in emergencies, and
except for persons observing loading or unloading operations by means
of video cameras and monitors or instrumentation and signaling systems
such as sensors, alarms, and electronic surveillance equipment located
at a remote control station and persons inspecting hoses in accordance
with paragraph (i)(3)(iii) of this section, is authorized to move the
cargo tank, and has the means to do so.
* * * * *
(l) * * *
(2) * * *
(i) Use of combustion cargo heaters. A motor vehicle equipped with
a combustion cargo heater may be used to transport Class 3 (flammable
liquid) or Division 2.1 (flammable gas) materials only subject to the
following conditions:
(A) The combustion cargo heater is powered by diesel fuel or
propane and each of the following requirements are met:
(1) Electrical apparatus in the cargo compartment is non-sparking
or explosion proof.
(2) There is no combustion apparatus in the cargo compartment.
(3) There is no connection for return of air from the cargo
compartment to the combustion apparatus.
(4) The heating system will not heat any part of the cargo to more
than 54 [deg]C (130[emsp14][deg]F).
(5) Heater requirements under Sec. 393.77 of this title are
complied with.
(6) The heater unit and its fuel supply must be externally mounted
on the truck or trailer.
(7) The heater unit must retain combustion in a sealed combustion
chamber.
(8) The heater unit must utilize outside air for combustion (air
from the cargo space cannot be used for combustion).
(9) Heater unit combustion gases must be exhausted to the outside
of the truck or trailer.
(B) The combustion cargo heater is a catalytic heater and each of
the following requirements are met:
(1) The heater's surface temperature cannot exceed 54 [deg]C
(130[emsp14][deg]F)--either on a thermostatically controlled heater or
on a heater without thermostatic control when the outside or ambient
temperature is 16 [deg]C (61[emsp14][deg]F) or less.
(2) The heater is not ignited in a loaded vehicle.
(3) There is no flame, either on the catalyst or anywhere in the
heater.
(4) The manufacturer has certified that the heater meets the
requirements under paragraph (l)(2)(i)(B) of this section by
permanently marking the heater ``MEETS DOT REQUIREMENTS FOR CATALYTIC
HEATERS USED
[[Page 3684]]
WITH FLAMMABLE LIQUID AND GAS.''
(5) The heater is also marked ``DO NOT LOAD INTO OR USE IN CARGO
COMPARTMENTS CONTAINING FLAMMABLE LIQUID OR GAS IF FLAME IS VISIBLE ON
CATALYST OR IN HEATER.''
(6) Heater requirements under Sec. 393.77 of this title are
complied with.
(ii) [Reserved]
* * * * *
0
42. In Sec. 177.838, the heading of the section is revised and
paragraph (i) is added to read as follows:
Sec. 177.838 Class 4 (flammable solid) materials, Class 5 (oxidizing)
materials, and Division 4.2 (self-heating and pyrophoric liquid)
materials.
* * * * *
(i) Division 4.2 (self-heating liquid) material. Notwithstanding
the segregation requirements of Sec. 177.848(d), the following
Division 4.2 (self-heating) materials may be transported on the same
transport vehicle with Class 8 (corrosive) materials. The hazardous
materials must be palletized with a minimum height of 100 mm (4 inches)
off the floor of the vehicle, and the self-heating material must be
separated from the corrosive material by a minimum horizontal distance
of 1.2 m (4 feet).
(1) Sodium hydrosulfite or sodium dithionite, UN1384, in PG II or
III packaged in UN 1A2 steel drums that meet the Packing Group II
performance requirements of subpart M of part 178 of this title.
(2) Thiourea dioxide, UN3341, in PG II or III packaged in UN 1G
fiber drums meeting packing group II performance requirements of
subpart M of part 178 of this subchapter.
(3) Self-heating, solid, organic, n.o.s., UN3088, in PG II or III
packaged in UN 1G fiber drums meeting the Packing Group II performance
level requirements of subpart M of part 178 of this subchapter.
0
43. In Sec. 177.840, add paragraph (a)(3) to read as follows:
Sec. 177.840 Class 2 (gases) materials.
(a) * * *
(3) Cylinders containing material classed as Division 2.3, Hazard
Zone A. (i) Notwithstanding the segregation requirements of Sec.
177.848(d), a cylinder containing a Division 2.3, Hazard Zone A
materials may be transported on the same transport vehicle with
materials classed as Division 2.1, Class 3, Class 4, Class 5, and Class
8 if all of the following requirements are met:
(A) The Division 2.3, Hazard Zone A material must be packaged as
authorized by this subchapter. In addition, each package must be must
be placed in a plastic bag which is taped closed and then overpacked in
a UN 1A2 steel drum tested and marked for a PG II or higher performance
level with insulation material inside to protect the cylinders from
fire. The outside of the overpack must be marked with an indication
that the inner packagings conform to the prescribed specifications.
(B) A Division 2.1 material requiring strong non-bulk outer
packagings in accordance with Sec. 173.301(a)(9) of this subchapter
must be overpacked in a UN 1A2 steel or 1H2 plastic drum tested and
marked for a PG II or higher performance level. The outside of the
overpack must be marked with an indication that the inner packagings
conform to the prescribed specifications.
(C) Packages containing Division 2.3 Hazard Zone A material must be
separated within the transport vehicle from packages containing
Division 2.1, Class 3, Class 4, Class 5, and Class 8 materials by a
minimum horizontal distance of 1.2 m (4 feet). In addition, all steel
or plastic overpacks containing packages of Division 2.3, Hazard Zone A
or Division 2.1 material must be placed on pallets within the transport
vehicle.
(ii) Notwithstanding the segregation requirements of Sec.
177.848(d), Division 2.3, Hazard Zone A material may be transported on
the same transport vehicle with non-bulk packagings and IBCs meeting a
UN performance standard containing only the residue of Division 2.1,
4.3, 5.1, and Class 3 and 8 materials if all of the following
requirements are met:
(A) The materials are transported in enclosed trailers equipped
with inlet and outlet vent openings with a minimum total area of one
square foot per 1,000 cubic feet of trailer volume. Electrical systems
within the trailer's interior must be non-sparking or explosion proof.
(B) Cylinders must be transported in an upright position and
securely restrained within the trailer, or loaded into racks, secured
to pallets, or packed in wooden or fiberboard boxes or crates to
prevent the cylinders from shifting or overturning within the motor
vehicle under normal transportation conditions. If cylinders are
secured to a pallet, the pallet must be designed to transport 1,590 kg
(3,500 lbs.) per pallet and the cylinders must be secured within the
pallet by a web strap rated at 4,545 kg (10,000 lbs.).
(C) A cylinder containing Division 2.3 Hazard Zone A materials must
be separated from non-bulk packagings and IBCs meeting a UN performance
standard containing the residue of materials in Division 2.1, 4.3, or
5.1, or Class 3 or 8 by a minimum horizontal distance of 3 m (10 feet).
The maximum gross weight of Division 2.3 Hazard Zone A material carried
on one vehicle must not exceed 3,636 kg (8,000 lbs.).
(D) Motor carriers must have a satisfactory safety rating as
prescribed in 49 CFR part 385.
* * * * *
0
44. In Sec. 177.841, add paragraph (f) to read as follows:
Sec. 177.841 Division 6.1 and Division 2.3 materials.
* * * * *
(f) Notwithstanding the segregation requirements of Sec.
177.848(d), when transported by highway by private or contract motor
carrier, Division 6.1 PG I, Hazard Zone A toxic-by-inhalation (TIH)
materials meeting the definition of a hazardous waste as provided in
Sec. 171.8 of this subchapter, may be transported on the same
transport vehicle with materials classed as Class 3, Class 4, Class 5,
and Class 8. The Division 6.1 PG I, Hazard Zone A materials must be
loaded on pallets and separated from the Class 3, Class 4, Class 5, and
Class 8 materials by a minimum horizontal distance of 2.74 m (9 feet)
when in conformance with the following:
(1) The TIH materials are packaged in combination packagings as
prescribed in Sec. 173.226(c) of this subchapter.
(2) The combination packages containing TIH materials must be:
(i) Filled and packed by the offeror's hazmat employees;
(ii) Be placed on pallets, when in a transport vehicle; and
(iii) Separated from hazardous materials classed as Class 3, Class
8 or Divisions 4.1, 4.2, 4.3, 5.1, or 5.2 by a nine-foot (minimum
distance) buffer zone, when in a transport vehicle. The buffer zone
maybe established by:
(A) A load lock;
(B) Empty drums;
(C) Drums containing hazardous materials (e.g., Class 9) that are
compatible with materials in all other drums immediately around them;
or
(D) Drums containing non-hazardous materials that are compatible
with materials in all other drums immediately around them.
PART 178--SPECIFICATIONS FOR PACKAGINGS
0
45. The authority citation for part 178 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; 49 CFR 1.81 and 1.97.
[[Page 3685]]
0
46. Sections 178.33c, 178.33c-1, and 178.33c-2 are added to subpart B
to read as follows:
Sec. 178.33c Specification 2P; inner nonrefillable metal receptacle
variation.
Sec. 178.33c-1 Compliance.
Required in all details.
Sec. 178.33c-2 Variation.
Notwithstanding the variation provided in this section, each
container must otherwise conform to a DOT 2P container in accordance
with Sec. 178.33. The following conditions also apply under Variation
1--
(a) Manufacture. Side seams: not permitted. Ends: The ends shall be
designed to withstand pressure and be equipped with a pressure relief
system (e.g., rim-venting release or a dome expansion device) designed
to function prior to bursting of the container.
(b) Tests. (1) One out of each lot of 25,000 containers or less,
successively produced per day complete with ends assembled (and without
a pressure relief system assembled) shall be pressure tested to
destruction at gauge pressure and must not burst below 240 psig. For
containers with a pressure relief system as described in paragraph (a)
of this section and assembled, failure at a location other than the
pressure relief system will reject the lot. For containers with an end
expansion device, the lot must be rejected if the container bursts
prior to buckling of the device.
(2) Each such 25,000 containers or less, successively produced per
day, shall constitute a lot and if the test container(s) shall fail,
the lot shall be rejected. Otherwise, ten (10) additional containers of
each container design produced may be selected at random and subjected
to the test. These containers shall be complete with ends assembled.
Should any of the containers thus tested fail, the entire lot must be
rejected. All containers constituting a lot shall be of like material,
size, design construction, finish, and quality.
(c) Marking. By means of printing, lithographing, embossing, or
stamping, each container must be marked:
(1) DOT-2P1.
(2) With the name or symbol of the person making the mark. A
symbol, if used, must be registered with the Associate Administrator.
0
47. Sections 178.33d, 178.33d-1, 178.33d-2 and 178.33d-3 are added to
subpart B to read as follows:
Sec. 178.33d Specification 2Q; inner nonrefillable metal receptacle
variations.
Sec. 178.33d-1 Compliance.
Required in all details.
Sec. 178.33d-2 Variation 1.
Notwithstanding the variation provided in this paragraph, each
container must otherwise conform to a DOT 2Q container in accordance
with Sec. 178.33a. The following conditions also apply under Variation
1--
(a) Type and size. The maximum capacity of containers in this class
may not exceed 0.40 L (24.4 cubic inches). The maximum inside diameter
shall not exceed 2.1 inches.
(b) Manufacture. Ends: The top of the container must be designed
with a pressure relief system consisting of radial scores on the top
seam(s). The bottom of the container must be designed to buckle at a
pressure greater than the pressure at which the top buckles and vents.
(c) Wall thickness. The minimum wall thickness for any container
shall be 0.0085 inches.
(d) Tests. (1) Two containers (one without a pressure relief system
and one with) out of each lot of 25,000 or less, successively produced
per day shall be pressure tested to destruction at gauge pressure. The
container without a pressure relief system must not burst below 320
psig. The container assembled with a pressure relief system as
described in paragraph (b) of this section must be tested to
destruction. The bottom of the container must buckle at a pressure
greater than the pressure at which the top buckles and vents.
(2) Each such 25,000 containers or less, successively produced per
day, shall constitute a lot and if the test container(s) shall fail,
the lot shall be rejected. Otherwise, ten (10) additional pairs of
containers may be selected at random and subjected to the test under
which failure occurred. Should any of the containers thus tested fail,
the entire lot must be rejected. All containers constituting a lot
shall be of like material, size, design construction, finish, and
quality.
(e) Marking. By means of printing, lithographing, embossing, or
stamping, each container must be marked:
(1) DOT-2Q1.
(2) With the name or symbol of the person making the mark. A
symbol, if used, must be registered with the Associate Administrator.
Sec. 178.33d-3 Variation 2.
Notwithstanding the variation provided in this paragraph, each
container must otherwise conform to a DOT 2Q container in accordance
with Sec. 178.33a. The following conditions also apply under Variation
2--
(a) Manufacture. Ends: The ends shall be designed to withstand
pressure and the container equipped with a pressure relief system
(e.g., rim-venting release or a dome expansion device) designed to
buckle prior to the burst of the container.
(b) Tests. (1) One out of each lot of 25,000 containers or less,
successively produced per day shall be pressure tested to destruction
at gauge pressure and must not burst below 270 psig. For containers
with a pressure relief system as described in paragraph (a) of this
section and assembled, failure at a location other than the pressure
relief system will reject the lot.
(2) Each such 25,000 containers or less, successively produced per
day, shall constitute a lot and if the test container(s) shall fail,
the lot shall be rejected. Otherwise, ten (10) additional containers of
each container design produced may be selected at random and subjected
to the test. These containers shall be complete with ends assembled.
Should any of the containers thus tested fail, the entire lot must be
rejected. All containers constituting a lot shall be of like material,
size, design construction, finish, and quality.
(c) Marking. By means of printing, lithographing, embossing, or
stamping, each container must be marked:
(1) DOT-2Q2.
(2) With the name or symbol of the person making the mark. A
symbol, if used, must be registered with the Associate Administrator.
PART 180--CONTINUING QUALIFICATION AND MAINTENANCE OF PACKAGINGS
0
48. The authority citation for part 180 continues to read as follows:
Authority: 49 U.S.C. 5101-5128; 49 CFR 1.81 and 1.97.
0
49. Section 180.209 is amended as follows:
0
a. In paragraph (a), Table 1 ``Requalification of Cylinders'' is
revised, and a footnote is added;
0
b. Revise paragraph (e); and
0
c. Amend the Table in paragraph (g) by adding an entry for ``DOT 4BW''
at the end of the table.
The revision and amendments read as follows.
Sec. 180.209 Requirements for requalification of specification
cylinders.
(a) * * *
[[Page 3686]]
Table 1--Requalification of Cylinders \1\
------------------------------------------------------------------------
Minimum test
Specification under which pressure (psig) Requalification
cylinder was made \2\ period (years)
------------------------------------------------------------------------
DOT 3........................... 3000 psig......... 5.
DOT 3A, 3AA..................... 5/3 times service 5, 10, or 12 (see
pressure, except Sec.
noncorrosive 180.209(b), (e),
service (see Sec. (f), (h), and
180.209(g)). (j).
DOT 3AL......................... 5/3 times service 5, 10 or 12 (see
pressure. Sec.
180.209(e), (j)
and Sec.
180.209(m) \3\).
DOT 3AX, 3AAX................... 5/3 times service 5, 10 (see Sec.
pressure. 180.209(e).
3B, 3BN......................... 2 times service 5 or 10 (see Sec.
pressure (see 180.209(e),
Sec. (f)).
180.209(g)).
3E.............................. Test not required.
3HT............................. 5/3 times service 3 (see Sec. Sec.
pressure. 180.209(k) and
180.213(c)).
3T.............................. 5/3 times service 5.
pressure.
4AA480.......................... 2 times service 5 or 10 (see Sec.
pressure (see 180.209(e) or
Sec. (h)).
180.209(g)).
4B, 4BA, 4BW, 4B-240ET.......... 2 times service 5, 10, or 12 (see
pressure, except Sec.
non-corrosive 180.209(e), (f),
service (see Sec. and (j)).
180.209(g)).
4D, 4DA, 4DS.................... 2 times service... 5.
DOT 4E.......................... 2 times service 5 or 10 (see Sec.
pressure, except 180.209(e)).
non-corrosive
(see Sec.
180.209(g)).
4L.............................. Test not required.
8, 8AL.......................... .................. 10 or 20 (see Sec.
180.209(i)).
Exemption or special permit See current See current
cylinder. exemption or exemption or
special permit. special permit.
Foreign cylinder (see Sec. As marked on 5 (see Sec. Sec.
173.301(j) of this subchapter cylinder, but not 180.209(l) and
for restrictions on use). less than 5/3 of 180.213(d)(2)).
any service or
working pressure
marking.
------------------------------------------------------------------------
\1\ Any cylinder not exceeding 2 inches outside diameter and less than 2
feet in length is excepted from volumetric expansion test.
\2\ For cylinders not marked with a service pressure, see Sec.
173.301a(b) of this subchapter.
\3\ This provision does not apply to cylinders used for carbon dioxide,
fire extinguisher or other industrial gas service.
* * * * *
(e) Proof pressure test. A cylinder made in conformance with DOT
Specifications 4B, 4BA, 4BW, or 4E protected externally by a suitable
corrosion-resistant coating and used exclusively for non-corrosive gas
that is commercially free from corroding components may be requalified
by volumetric expansion testing or proof pressure testing every 10
years instead of every 5 years. When subjected to a proof pressure
test, the cylinder must be carefully examined under test pressure and
removed from service if a leak or defect is found.
* * * * *
(g) * * *
----------------------------------------------------------------------------------------------------------------
Cylinders conforming to . . . Used exclusively for . . .
----------------------------------------------------------------------------------------------------------------
* * * * * * *
DOT 4BW................................................... Alkali metal alloys, liquid, n.o.s., Alkali metal
dispersions or Alkaline earth metal dispersions,
Potassium, Potassium Sodium alloys and Sodium that
are commercially free of corroding components.
----------------------------------------------------------------------------------------------------------------
* * * * *
0
50. In Sec. 180.213, revise paragraph (c) introductory text to read as
follows:
Sec. 180.213 Requalification markings.
* * * * *
(c) Requalification marking method. The depth of requalification
markings may not be greater than specified in the applicable
specification. The markings must be made by stamping, engraving,
scribing, or applying a label embedded in epoxy that will remain
legible and durable throughout the life of the cylinder, or by other
methods that produce a legible, durable mark.
* * * * *
Marie Therese Dominguez,
Administrator, Pipeline and Hazardous Materials Safety Administration.
[FR Doc. 2016-00780 Filed 1-20-16; 8:45 am]
BILLING CODE 4910-60-P