[Federal Register Volume 82, Number 146 (Tuesday, August 1, 2017)]
[Rules and Regulations]
[Pages 35634-35636]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-15476]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0331; Directorate Identifier 2016-NM-213-AD; 
Amendment 39-18971; AD 2017-15-11]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
Bombardier, Inc., Model DHC-8-102, -103, -106, -201, -202, -301, -311, 
and -315 airplanes. This AD was prompted by reports of undamped main 
landing gear (MLG) extension in-service. This AD requires replacement 
of the MLG retraction actuator rod-ends on both MLG assemblies. We are 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective September 5, 2017.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 5, 
2017.

ADDRESSES: For service information identified in this final rule, 
contact Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; email [email protected]; Internet 
http://www.bombardier.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221. It is also available on the 
Internet at http://www.regulations.gov by searching for and locating 
Docket No. FAA-2017-0331.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0331; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The street address for the Docket Office (telephone 
800-647-5527) is Docket Management Facility, U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; telephone 516-228-7303; fax 516-794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to certain Bombardier, Inc., 
Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 
airplanes. The NPRM published in the Federal Register on May 2, 2017 
(82 FR 20453) (``the NPRM''). The NPRM was prompted by reports of 
undamped MLG extension in-service. The NPRM proposed to require 
replacement of the MLG retraction actuator rod-ends on both MLG 
assemblies. We are issuing this AD to prevent MLG undamped extensions, 
which could result in MLG structural failure, resulting in an unsafe 
asymmetric landing gear configuration.
    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2016-36, dated November 22, 2016 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition

[[Page 35635]]

for certain Bombardier, Inc., Model DHC-8-102, -103, -106, -201, -202, 
-301, -311, and -315 airplanes. The MCAI states:

    Two cases of undamped main landing gear (MLG) extension were 
reported in-service. Investigation determined that the MLG 
retraction actuator rod-ends failed as a result of non-conforming 
threads. This condition, if not corrected, could lead to additional 
MLG undamped extensions, which may result in MLG structural failure, 
resulting in an unsafe asymmetric landing gear configuration.
    This [Canadian] AD mandates the replacement of the MLG 
retraction actuator rod-end subassemblies manufactured with non-
conforming threads with units that fully conform to the design 
requirements.

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0331.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We considered the comment received. Air Line Pilots 
Association, International supported the NPRM.

Conclusion

    We reviewed the relevant data, considered the comment received, and 
determined that air safety and the public interest require adopting 
this AD as proposed except for minor editorial changes. We have 
determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for correcting the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    Bombardier, Inc., issued Service Bulletin 8-32-179, Revision A, 
dated March 9, 2017. This service information describes procedures for 
replacing the MLG retraction actuator rod-ends on both MLG assemblies 
with units that fully conform to the design requirements. This service 
information is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Costs of Compliance

    We estimate that this AD affects 91 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
               Action                         Labor cost            Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Replacement........................  3 work-hours x $85 per hour          $2,078          $2,333        $212,303
                                      = $255.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2017-15-11 Bombardier, Inc.: Amendment 39-18971; Docket No. FAA-
2017-0331; Directorate Identifier 2016-NM-213-AD.

(a) Effective Date

    This AD is effective September 5, 2017.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model DHC-8-102, -103, -
106, -201, -202, -301, -311, and -315 airplanes, certificated in any 
category, serial numbers 003 through 672 inclusive, equipped with 
main landing gear (MLG) retraction actuator assembly part number 
10500-101, -103, -501, -551, or -553.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
Gear.

(e) Reason

    This AD was prompted by reports of undamped MLG extension in-
service. We are issuing this AD to prevent MLG undamped extensions, 
which could result in MLG structural failure, resulting in an unsafe 
asymmetric landing gear configuration.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement of MLG Retraction Actuator Rod-Ends

    At the applicable time specified in paragraph (g)(1) or (g)(2) 
of this AD: Replace the MLG retraction actuator rod-ends on both MLG 
assemblies, in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 8-32-179, Revision A, dated March 9, 
2017.

[[Page 35636]]

    (1) For MLG retraction actuator assemblies with 37,000 total 
flight cycles or more as of the effective date of this AD: Within 18 
months or 2,700 flight cycles, whichever occurs first after the 
effective date of this AD.
    (2) For MLG retraction actuator assemblies with fewer than 
37,000 total flight cycles as of the effective date of this AD: 
Within 24 months or 3,600 flight cycles, whichever occurs first 
after the effective date of this AD.

(h) Alternative Installation of Part Number (P/N) 10500-105, -503, or -
555

    Installation of MLG retraction actuator assembly P/N 10500-105, 
-503, or -555 on both MLGs is acceptable for compliance with the 
replacement required by paragraph (g) of this AD.

(i) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Bombardier Service Bulletin 8-32-179, dated 
July 10, 2015.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the ACO, send it to ATTN: Program 
Manager, Continuing Operational Safety, FAA, New York ACO, 1600 
Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-
7300; fax 516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2016-36, dated November 
22, 2016, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2017-0331.
    (2) For more information about this AD, contact Fabio Buttitta, 
Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE-171, 
FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone 516-228-7303; fax 516-794-5531.
    (3) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (l)(3) and (l)(4) of this AD.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 8-32-179, Revision A, dated 
March 9, 2017.
    (ii) Reserved.
    (3) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; email [email protected]; Internet 
http://www.bombardier.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on July 14, 2017.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-15476 Filed 7-31-17; 8:45 am]
 BILLING CODE 4910-13-P