[Title 46 CFR ]
[Code of Federal Regulations (annual edition) - October 1, 2001 Edition]
[From the U.S. Government Printing Office]
[[Page i]]
46
Parts 90 to 139
Revised as of October 1, 2001
Shipping
Containing a codification of documents of general
applicability and future effect
As of October 1, 2001
With Ancillaries
Published by
Office of the Federal Register
National Archives and Records
Administration
A Special Edition of the Federal Register
[[Page ii]]
U.S. GOVERNMENT PRINTING OFFICE
WASHINGTON : 2001
For sale by the Superintendent of Documents, U.S. Government Printing
Office
Internet: bookstore.gpo.gov Phone: toll free (866) 512-1800; DC area
(202) 512-1800
Fax: (202) 512-2250 Mail: Stop SSOP, Washington, DC 20402-0001
[[Page iii]]
Table of Contents
Page
Explanation................................................. v
Title 46:
Chapter I--Coast Guard, Department of
Transportation--Continued 3
Finding Aids:
Material Approved for Incorporation by Reference........ 495
Table of CFR Titles and Chapters........................ 509
Alphabetical List of Agencies Appearing in the CFR...... 527
List of CFR Sections Affected........................... 537
[[Page iv]]
----------------------------
Cite this Code: CFR
To cite the regulations in
this volume use title,
part and section number.
Thus, 46 CFR 90.01-1
refers to title 46, part
90, section 01-1.
----------------------------
[[Page v]]
EXPLANATION
The Code of Federal Regulations is a codification of the general and
permanent rules published in the Federal Register by the Executive
departments and agencies of the Federal Government. The Code is divided
into 50 titles which represent broad areas subject to Federal
regulation. Each title is divided into chapters which usually bear the
name of the issuing agency. Each chapter is further subdivided into
parts covering specific regulatory areas.
Each volume of the Code is revised at least once each calendar year
and issued on a quarterly basis approximately as follows:
Title 1 through Title 16.................................as of January 1
Title 17 through Title 27..................................as of April 1
Title 28 through Title 41...................................as of July 1
Title 42 through Title 50................................as of October 1
The appropriate revision date is printed on the cover of each
volume.
LEGAL STATUS
The contents of the Federal Register are required to be judicially
noticed (44 U.S.C. 1507). The Code of Federal Regulations is prima facie
evidence of the text of the original documents (44 U.S.C. 1510).
HOW TO USE THE CODE OF FEDERAL REGULATIONS
The Code of Federal Regulations is kept up to date by the individual
issues of the Federal Register. These two publications must be used
together to determine the latest version of any given rule.
To determine whether a Code volume has been amended since its
revision date (in this case, October 1, 2001), consult the ``List of CFR
Sections Affected (LSA),'' which is issued monthly, and the ``Cumulative
List of Parts Affected,'' which appears in the Reader Aids section of
the daily Federal Register. These two lists will identify the Federal
Register page number of the latest amendment of any given rule.
EFFECTIVE AND EXPIRATION DATES
Each volume of the Code contains amendments published in the Federal
Register since the last revision of that volume of the Code. Source
citations for the regulations are referred to by volume number and page
number of the Federal Register and date of publication. Publication
dates and effective dates are usually not the same and care must be
exercised by the user in determining the actual effective date. In
instances where the effective date is beyond the cut-off date for the
Code a note has been inserted to reflect the future effective date. In
those instances where a regulation published in the Federal Register
states a date certain for expiration, an appropriate note will be
inserted following the text.
OMB CONTROL NUMBERS
The Paperwork Reduction Act of 1980 (Pub. L. 96-511) requires
Federal agencies to display an OMB control number with their information
collection request.
[[Page vi]]
Many agencies have begun publishing numerous OMB control numbers as
amendments to existing regulations in the CFR. These OMB numbers are
placed as close as possible to the applicable recordkeeping or reporting
requirements.
OBSOLETE PROVISIONS
Provisions that become obsolete before the revision date stated on
the cover of each volume are not carried. Code users may find the text
of provisions in effect on a given date in the past by using the
appropriate numerical list of sections affected. For the period before
January 1, 1986, consult either the List of CFR Sections Affected, 1949-
1963, 1964-1972, or 1973-1985, published in seven separate volumes. For
the period beginning January 1, 1986, a ``List of CFR Sections
Affected'' is published at the end of each CFR volume.
INCORPORATION BY REFERENCE
What is incorporation by reference? Incorporation by reference was
established by statute and allows Federal agencies to meet the
requirement to publish regulations in the Federal Register by referring
to materials already published elsewhere. For an incorporation to be
valid, the Director of the Federal Register must approve it. The legal
effect of incorporation by reference is that the material is treated as
if it were published in full in the Federal Register (5 U.S.C. 552(a)).
This material, like any other properly issued regulation, has the force
of law.
What is a proper incorporation by reference? The Director of the
Federal Register will approve an incorporation by reference only when
the requirements of 1 CFR part 51 are met. Some of the elements on which
approval is based are:
(a) The incorporation will substantially reduce the volume of
material published in the Federal Register.
(b) The matter incorporated is in fact available to the extent
necessary to afford fairness and uniformity in the administrative
process.
(c) The incorporating document is drafted and submitted for
publication in accordance with 1 CFR part 51.
Properly approved incorporations by reference in this volume are
listed in the Finding Aids at the end of this volume.
What if the material incorporated by reference cannot be found? If
you have any problem locating or obtaining a copy of material listed in
the Finding Aids of this volume as an approved incorporation by
reference, please contact the agency that issued the regulation
containing that incorporation. If, after contacting the agency, you find
the material is not available, please notify the Director of the Federal
Register, National Archives and Records Administration, Washington DC
20408, or call (202) 523-4534.
CFR INDEXES AND TABULAR GUIDES
A subject index to the Code of Federal Regulations is contained in a
separate volume, revised annually as of January 1, entitled CFR Index
and Finding Aids. This volume contains the Parallel Table of Statutory
Authorities and Agency Rules (Table I). A list of CFR titles, chapters,
and parts and an alphabetical list of agencies publishing in the CFR are
also included in this volume.
An index to the text of ``Title 3--The President'' is carried within
that volume.
The Federal Register Index is issued monthly in cumulative form.
This index is based on a consolidation of the ``Contents'' entries in
the daily Federal Register.
A List of CFR Sections Affected (LSA) is published monthly, keyed to
the revision dates of the 50 CFR titles.
[[Page vii]]
REPUBLICATION OF MATERIAL
There are no restrictions on the republication of material appearing
in the Code of Federal Regulations.
INQUIRIES
For a legal interpretation or explanation of any regulation in this
volume, contact the issuing agency. The issuing agency's name appears at
the top of odd-numbered pages.
For inquiries concerning CFR reference assistance, call 202-523-5227
or write to the Director, Office of the Federal Register, National
Archives and Records Administration, Washington, DC 20408 or e-mail
[email protected].
SALES
The Government Printing Office (GPO) processes all sales and
distribution of the CFR. For payment by credit card, call 202-512-1800,
M-F, 8 a.m. to 4 p.m. e.s.t. or fax your order to 202-512-2250, 24 hours
a day. For payment by check, write to the Superintendent of Documents,
Attn: New Orders, P.O. Box 371954, Pittsburgh, PA 15250-7954. For GPO
Customer Service call 202-512-1803.
ELECTRONIC SERVICES
The full text of the Code of Federal Regulations, The United States
Government Manual, the Federal Register, Public Laws, Public Papers,
Weekly Compilation of Presidential Documents and the Privacy Act
Compilation are available in electronic format at www.access.gpo.gov/
nara (``GPO Access''). For more information, contact Electronic
Information Dissemination Services, U.S. Government Printing Office.
Phone 202-512-1530, or 888-293-6498 (toll-free). E-mail,
[email protected].
The Office of the Federal Register also offers a free service on the
National Archives and Records Administration's (NARA) World Wide Web
site for public law numbers, Federal Register finding aids, and related
information. Connect to NARA's web site at www.nara.gov/fedreg. The NARA
site also contains links to GPO Access.
Raymond A. Mosley,
Director,
Office of the Federal Register.
October 1, 2001.
[[Page ix]]
THIS TITLE
Title 46--Shipping is composed of nine volumes. The parts in these
volumes are arranged in the following order: Parts 1-40, 41-69, 70-89,
90-139, 140-155, 156-165, 166-199, 200-499 and 500 to End. The first
seven volumes containing parts 1-199 comprise chapter I--Coast Guard,
DOT. The eighth volume, containing parts 200 to 499, includes chapter
II--Maritime Administration, DOT and chapter III--Coast Guard (Great
Lakes Pilotage), DOT. The ninth volume, containing part 500 to End,
includes chapter IV--Federal Maritime Commission. The contents of these
volumes represent all current regulations codified under this title of
the CFR as of October 1, 2001.
Subject indexes appear in subchapters A--I, I-A, J, K, L, and Q--W
following the subchapters.
[[Page x]]
[[Page 1]]
TITLE 46--SHIPPING
(This book contains parts 90 to 139)
--------------------------------------------------------------------
Part
chapter i--Coast Guard, Department of Transportation
(Continued)............................................... 90
[[Page 3]]
CHAPTER I--COAST GUARD, DEPARTMENT OF
TRANSPORTATION--Continued
--------------------------------------------------------------------
SUBCHAPTER I--CARGO AND MISCELLANEOUS VESSELS
Part Page
90 General provisions.......................... 5
91 Inspection and certification................ 16
92 Construction and arrangement................ 36
93 Stability................................... 45
95 Fire protection equipment................... 46
96 Vessel control and miscellaneous systems and
equipment............................... 60
97 Operations.................................. 66
98 Special construction, arrangement, and other
provisions for certain dangerous cargoes
in bulk................................. 80
105 Commercial fishing vessels dispensing
petroleum products...................... 94
Index....................................... 181
SUBCHAPTER I-A--MOBILE OFFSHORE DRILLING UNITS
107 Inspection and certification................ 104
108 Design and equipment........................ 118
109 Operations.................................. 160
Index....................................... 181
SUBCHAPTER J--ELECTRICAL ENGINEERING
110 General provisions.......................... 200
111 Electric systems--general requirements...... 210
112 Emergency lighting and power systems........ 252
113 Communication and alarm systems and
equipment............................... 262
Index....................................... 275
SUBCHAPTER K--SMALL PASSENGER VESSELS CARRYING MORE THAN 150 PASSENGERS
OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS
114 General provisions.......................... 289
115 Inspection and certification................ 301
116 Construction and arrangement................ 316
117 Lifesaving equipment and arrangements....... 336
[[Page 4]]
118 Fire protection equipment................... 347
119 Machinery installation...................... 355
120 Electrical installation..................... 366
121 Vessel control and miscellaneous systems and
equipment............................... 375
122 Operations.................................. 380
123-124 [Reserved]
Index....................................... 397
SUBCHAPTER L--OFFSHORE SUPPLY VESSELS
125 General..................................... 411
126 Inspection and certification................ 416
127 Construction and arrangements............... 424
128 Marine engineering: Equipment and systems... 429
129 Electrical installations.................... 431
130 Vessel control, and miscellaneous equipment
and systems............................. 440
131 Operations.................................. 445
132 Fire-protection equipment................... 461
133 Lifesaving systems.......................... 466
134 Added provisions for liftboats.............. 479
135-139 [Reserved]
Index....................................... 483
[[Page 5]]
SUBCHAPTER I--CARGO AND MISCELLANEOUS VESSELS
PART 90--GENERAL PROVISIONS--Table of Contents
Subpart 90.01--Authority and Purpose
Sec.
90.01-1 Purpose of regulations.
90.01-7 Right of appeal.
90.01-15 OMB control numbers assigned pursuant to the Paperwork
Reduction Act.
Subpart 90.05--Application
90.05-1 Vessels subject to requirements of this subchapter.
90.05-5 Specific application noted in text.
90.05-7 Ocean or unlimited coastwise vessels on inland and Great Lakes
routes.
90.05-10 Application to vessels on an international voyage.
90.05-20 Applicability to offshore supply vessels.
90.05-25 Seagoing barge.
90.05-35 Flammable and combustible liquid cargo in bulk.
Subpart 90.10--Definition of Terms Used in This Subchapter
90.10-1 Anniversary date.
90.10-2 Approved.
90.10-3 Barge.
90.10-5 Carrying freight for hire.
90.10-7 Commandant.
90.10-9 Coast Guard District Commander.
90.10-11 Coastwise.
90.10-12 Gas free.
90.10-13 Great Lakes.
90.10-14 Headquarters.
90.10-15 Industrial personnel.
90.10-16 Industrial vessel.
90.10-19 Lakes, bays, and sounds.
90.10-20 Liftboat.
90.10-21 Marine inspector or inspector.
90.10-23 Motorboat.
90.10-25 Ocean.
90.10-27 Officer in Charge, Marine Inspection (OCMI).
90.10-29 Passenger.
90.10-30 Pilot boarding equipment and point of access.
90.10-33 Rivers.
90.10-35 Recognized classification society.
90.10-36 Seagoing barge.
90.10-37 Vessel.
90.10-38 Specially suitable for vehicles.
90.10-40 Offshore supply vessels.
90.10-42 Tankerman
Subpart 90.15--Equivalents
90.15-1 Conditions under which equivalents may be used.
Subpart 90.20--General Marine Engineering Requirements
90.20-1 Marine engineering details.
Subpart 90.25--General Electrical Engineering Requirements
90.25-1 Electrical engineering details.
Subpart 90.27--Lifesaving Appliances and Arrangements
90.27-1 Lifesaving appliances and arrangements.
Subpart 90.35--American Bureau of Shipping's Standards
90.35-1 Standards to be used.
90.35-5 Where obtainable.
Authority: 46 U.S.C. 3306, 3307, 3703; 49 U.S.C. 5103, 5106; E.O.
12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; 49 CFR 1.46.
Source: CGFR 65-50, 30 FR 16970, Dec. 30, 1965, unless otherwise
noted.
Subpart 90.01--Authority and Purpose
Sec. 90.01-1 Purpose of regulations.
The purpose of the regulations in this subchapter is to set forth
uniform minimum requirements for cargo and miscellaneous vessels, as
listed in Column 5 of table 90.05-1(a).
[CGD 95-028, 62 FR 51205, Sept. 30, 1997]
Sec. 90.01-7 Right of appeal.
Any person directly affected by a decision or action taken under
this subchapter, by or on behalf of the Coast Guard, may appeal
therefrom in accordance with subpart 1.03 of this chapter.
[CGD 88-033, 54 FR 50380, Dec. 6, 1989]
Sec. 90.01-15 OMB control numbers assigned pursuant to the Paperwork Reduction Act.
(a) Purpose. This section collects and displays the control numbers
assigned to information collection and recordkeeping requirements in
this subchapter by the Office of Management and Budget (OMB) pursuant to
the Paperwork Reduction Act of 1980 (44
[[Page 6]]
U.S.C. 3501 et seq.). The Coast Guard intends that this section comply
with the requirements of 44 U.S.C. 3507(f), which requires that agencies
display a current control number assigned by the Director of the OMB for
each approved agency information collection requirement.
(b) Display.
------------------------------------------------------------------------
Current OMB
46 CFR part or section where identified or described control No.
------------------------------------------------------------------------
Sec. 91.27-13............................................. 2115-0517
Sec. 91.40-3.............................................. 2115-0554
Sec. 91.40-5.............................................. 2115-0554
Sec. 97.15-7.............................................. 2115-0589
Sec. 97.15-17............................................. 2115-0589
------------------------------------------------------------------------
[CGD 88-072, 53 FR 34297, Sept. 6, 1988, as amended by CGD 82-004a, 55
FR 2525, Jan. 25, 1990; CGD 89-037, 57 FR 41822, Sept. 11, 1992]
Subpart 90.05--Application
Sec. 90.05-1 Vessels subject to requirements of this subchapter.
(a) This subchapter shall be applicable to all United States flag
vessels indicated in Column 5 of Table 90.05-1(a) and to all such
foreign vessels which carry 12 or less passengers from any port in the
United States to the extent prescribed by law, except as follows:
(1) Any vessel of a foreign nation signatory to the International
Convention for Safety of Life at Sea, 1974, and which has on board a
current, valid safety equipment certificate.
(2) Any vessel operating exclusively on inland waters which are not
navigable waters of the United States.
(3) Any vessel while laid up and dismantled and out of commission.
(4) With the exception of vessels of the U.S. Maritime
Administration, any vessel with title vested in the United States and
which is used for public purposes.
(b) Notwithstanding the exception previously noted in paragraph
(a)(1) of this section, foreign vessels of novel design or construction
or whose operation involves potential unusual risks shall be subject to
inspection to the extent necessary to safeguard life and property in
United States ports, as further provided by Sec. 2.01-13 of subchapter A
(Procedures Applicable to the Public) of this chapter.
(c) Notwithstanding the exception noted in paragraph (a)(1) of this
section, each foreign vessel shall report marine casualties occurring
while the vessel is in the navigable waters of the United States as
required by Subpart 97.07.
[[Page 7]]
Table 90.05-1(a)
[See footnotes at end of table]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Method of propulsion Size or other Classes of vessels (including motorboats) examined or inspected under various Coast Guard regulations \1\
-------------------------------- limitations \1\ --------------------------------------------------------------------------------------------------------------------------------------------
-------------------- Vessels inspected Vessels inspected and Vessels inspected Vessels subject to Vessels subject to Vessels subject to
and certificated certificated under and certificated provisions of Subchapter provisions of Subchapter the provisions of
under Subchapter either Subchapter H-- under Subchapter C--Uninspected Vessels U--Oceanographic Vessels Subchapter O--
D--Tank Vessels Passenger Vessels I--Cargo and \2\\3\\6\\7\\8\ \2\\5\\6\\7\\9\ Certain Bulk
\2\ \2\\3\\4\\5\ or Miscellaneous -------------------------------------------------------- Dangerous Cargoes
Column 1 Column 2 -------------------- Subchapter T--Small Vessels \2\\5\ \10\
Passenger Vessels -------------------- -------------------
\2\\3\\4\ Column 6 Column 7
Column 3 ------------------------- Column 5 Column 8
Column 4
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Steam.......................... Vessels not over All vessels All vessels carrying All tugboats and All vessels except those None...................... All vessels
65 feet in length. carrying more than 6 passengers towboats. covered by columns 3, 4, carrying in bulk
combustible or \7\. 5, and 7. the cargoes
flammable liquid listed in table I
cargo in bulk. of pt. 153 and
table 4 of pt.
154.
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Vessels over 65 All vessels 1. All vessels carrying All vessels except None...................... All vessels engaged in Do.
feet in length. carrying more than 12 those covered by oceanographic research.
combustible or passengers on an columns 3 and 4.
flammable liquid international voyage,
cargo in bulk \5\. except yachts.
2. All vessels of not
over 15 gross tons
which carry more than
6 passengers\7\
3. All other vessels
carrying
passengers,\7\ except:
a. Yachts
b. Documented
cargo or tank vessels
issued a permit to
carry not more than 16
persons in addition to
the crew
[[Page 8]]
c. Towing and
fishing vessels, in
other than ocean and
coastwise service, may
carry persons on the
legitimate business of
the vessel, in
addition to crew, but
not to exceed one for
each net ton of the
vessel
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Motor.......................... Vessels not over All vessels All vessels carrying Those vessels All vessels except those None...................... All vessels
15 gross tons. carrying more than 6 passengers carrying covered by columns 3, 4, carrying in bulk
combustible or \7\. dangerous cargoes 5, and 7. the cargoes
flammable liquid when required by listed in table I
cargo in bulk. 46 CFR part 98 or of pt. 153 and
49 CFR parts 171- table 4 of pt.
179. 154.
Vessels over 15 All vessels 1. All vessels carrying All vessels ......do.................. ......do.................. Do.
gross tons except carrying more than 12 carrying freight
seagoing motor combustible or passengers on an for hire except
vessels of 300 flammable liquid international voyage, those covered by
gross tons and cargo in bulk \5\. except yachts. columns 3 and 4.
over.
2. All vessels not
over 65 feet in length
which carry more than
6 passengers \7\
[[Page 9]]
3. All other vessels
of over 65 feet in
length carrying
passengers for hire
except documented
cargo or tank vessels
issued a permit to
carry not more than 16
persons in addition to
the crew
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Seagoing motor All vessels 1. All vessels carrying
vessels of 300 carrying more than 12
gross tons and combustible or passengers on an
over. flammable liquid international voyage,
cargo in bulk \5\. except yachts.
2. All other other
vessels carrying
passengers,\7\ except:
a. Yachts All vessels except All vessels except those All vessels engaged in Do.
b. Documented cargo those covered by covered by columns 3, 4, oceanographic research.
or tank vessels issued columns 3 and 4, 5, and 7.
a permit to carry not and those engaged
more than 16 persons in the fishing,
in addition to the oystering,
crew. clamming,
crabbing, or any
other branch of
the fishery,
kelp, or sponge
industry.
Sail........................... Vessels not over All vessels All vessels carrying Those vessels None...................... None...................... Do.
700 gross tons. carrying more than 6 passengers carrying
combustible or \7\. dangerous cargoes
flammable liquid when required by
cargo in bulk. 46 CFR part 98 or
49 CFR parts 171-
179.
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Vessels over 700 ......do.......... All vessels carrying ......do.......... None...................... None...................... Do.
gross tons. passengers for hire.
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Non-self propelled............. Vessels less than All vessels All vessels carrying ......do.......... All barges carrying None...................... All tank barges
100 gross tons. carrying more than 6 passengers passengers except those \11\ carrying in
combustible or \7\. covered by column 4. bulk the cargoes
liquid cargo in listed in table
bulk. 151.05 of this
chapter.\11\
----------------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 10]]
Vessels 100 gross All vessels All vessels carrying All seagoing All barges carrying All seagoing barges All tank barges
tons or over. carrying passengers for hire. barges except passengers except those engaged in oceanographic \11\ carrying in
combustible or those covered by covered by columns 4 and research. bulk the cargoes
flammable liquid columns 3 and 4; 7. listed in table
cargo in bulk. and those inland 151.05 of this
barges carrying chapter.\11\
dangerous cargoes
when required by
46 CFR part 98 or
49 CFR parts 171-
179.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Footnotes to Table 90.05-1(a):
\1\ Where length is used in this table it means the length measured from end to end over the deck, excluding sheer. This expression means a straight line measurement of the overall length from
the foremost part of the vessel to the aftermost part of the vessel, measured parallel to the centerline.
\2\ Subchapters E (Load Lines), F (Marine Engineering), J (Electrical Engineering), and N (Dangerous Cargoes) of this chapter may also be applicable under certain conditions. The provisions of
49 CFR parts 171-179 apply whenever hazardous materials are on board vessels (including motorboats), except when specifically exempted by law.
\3\ Public nautical schoolships, other than vessels of the Navy and Coast Guard, shall meet the requirements of part 167 of subchapter R (Nautical Schools) of this chapter. Civilian nautical
schoolships, as defined by 46 U.S.C. 1331, shall meet the requirements of subchapter H (Passenger Vessels) and part 168 of subchapter R (Nautical Schools) of this chapter.
\4\ Subchapter H (Passenger Vessels) of this chapter covers only those vessels of 100 gross tons or more. Subchapter T (Small Passenger Vessels) of this chapter covers only those vessels of
less than 100 gross tons.
\5\ Vessels covered by subchapter H (Passenger Vessels) or I (Cargo and Miscellaneous Vessels) of this chapter, where the principal purpose or use of the vessel is not for the carriage of
liquid cargo, may be granted a permit to carry a limited amount of flammable or combustible liquid cargo in bulk. The portion of the vessel used for the carriage of the flammable or
combustible liquid cargo shall meet the requirements of subchapter D (Tank Vessels) in addition to the requirements of subchapter H (Passenger Vessels) or I (Cargo and Miscellaneous Vessels)
of this chapter.
\6\ Any vessel on an international voyage is subject to the requirements of the International Convention for Safety of Life at Sea, 1974.
\7\ The meaning of the term ``passenger'' is as defined in the Act of May 10, 1956 (Sec. 1, 70 Stat. 151; 46 U.S.C. 390). On oceanographic vessels scientific personnel on board shall not be
deemed to be passengers nor seamen, but for calculations of lifesaving equipment, etc., shall be counted as persons.
\8\ Boilers and machinery are subject to examination on vessels over 40 feet in length.
\9\ Under 46 U.S.C. 441 an ``oceanographic research vessel'' is a vessel ``* * * being employed exclusively in instruction in oceanography or limnology, or both, or exclusively in
oceanographic research, * * *,'' Under 46 U.S.C. 443, ``an oceanographic research vessel shall not be deemed to be engaged in trade or commerce.'' If or when an oceanographic vessel engages
in trade or commerce, such vessel cannot operate under its certificate of inspection as an oceanographic vessel, but shall be inspected and certificated for the service in which engaged, and
the scientific personnel aboard then become persons employed in the business of the vessel.
\10\ Bulk dangerous cargoes are cargoes specified in table 151.01-10(b), in table I of part 153, and in table 4 of part 154 of this chapter.
\11\ For manned tank barges see Sec. 151.01-10(c) of this chapter.
[CGFR 65-50, 30 FR 16970, Dec. 30, 1965, as amended by CGFR 67-83, 33 FR
1109, Jan. 27, 1968; CGFR 70-10, 35 FR 3711, Feb. 25, 1970; CGD 73-96,
42 FR 49025, Sept. 26, 1977; CGD 77-042, 42 FR 63643, Dec. 19, 1977; CGD
86-033, 53 FR 36025, Sept. 16, 1988; CGD 86-033, 53 FR 46871, Nov. 21,
1988; CGD 90-008, 55 FR 30661, July 26, 1990]
[[Page 11]]
Sec. 90.05-5 Specific application noted in text.
(a) At the beginning of the various parts, subparts, and sections, a
more specific application is generally given for the particular portion
of the text involved. This application sets forth the types, sizes, or
services or vessels to which the text pertains, and in many cases limits
the application of the text to vessels contracted for before or after a
specific date. As used in this subchapter, the term ``vessels contracted
for'' includes not only the contracting for the construction of a
vessel, but also the contracting for a material alteration to a vessel,
the contracting for the conversion of a vessel to a cargo or
miscellaneous vessel, and the changing of service or route of a vessel
if such change increases or modifies the general requirements for the
vessel or increases the hazards to which it might be subjected.
Sec. 90.05-7 Ocean or unlimited coastwise vessels on inland and Great Lakes routes.
(a) Vessels inspected and certificated for ocean or unlimited
coastwise routes shall be considered suitable for navigation insofar as
the provisions of this subchapter are concerned on any inland routes,
including the Great Lakes.
Sec. 90.05-10 Application to vessels on an international voyage.
(a) Except for yachts and fishing vessels and as provided in
paragraphs (b), (c), and (d) of this section, the regulations in this
subchapter that apply to a vessel on an ``international voyage'' apply
to a vessel that--
(1) Is mechanically propelled and of at least 500 gross tons; and
(2) Is engaged on a voyage--
(i) From a country to which the International Convention for Safety
of Life at Sea, 1974, (SOLAS 74) applies, to a port outside that country
or the reverse;
(ii) From any territory, including the Commonwealth of Puerto Rico,
all possessions of the United States and all lands held by the United
States under a protectorate or mandate, whose international relations
are the responsibility of a contracting SOLAS 74 government, or which is
administered by the United Nations, to a port outside the territory or
the reverse; or
(iii) Between the contiguous states of the United States and the
states of Hawaii or Alaska or between the states of Hawaii and Alaska.
(b) The regulations that apply to a vessel on an ``international
voyage'' in this subchapter do not apply to ships engaged on a voyage
solely on the Great Lakes and the St. Lawrence River as far east as a
straight line drawn from Cap de Rosiers to West Point, Anticosti Island,
the 63d Meridian;
(c) The Commandant or his authorized representative may exempt any
vessel on an international voyage from the requirements of this
subchapter if the vessel--
(1) Makes a single international voyage in exceptional
circumstances; and
(2) Meets safety requirements prescribed for the voyage by the
Commandant.
(d) The Commandant or his authorized representative may exempt any
vessel from the construction requirements of this subchapter if the
vessel does not proceed more than 20 nautical miles from the nearest
land in the course of its voyage.
[CGD 72-131R, 38 FR 29320, Oct. 24, 1973, as amended by CGD 90-008, 55
FR 30661, July 26, 1990; CGD 84-069, 61 FR 25288, May 20, 1996]
Sec. 90.05-20 Applicability to offshore supply vessels.
(a) Existing offshore supply vessels as defined by Sec. 90.10-40(b),
if they are of 100 or more but of less than 500 gross tons, are subject
to inspection under this subchapter. New offshore supply vessels as
defined by Sec. 90.10-40(c), are subject to inspection under subchapter
L of this chapter.
(b) Each offshore supply vessel permitted grandfathering under
paragraph (a) of this section must complete construction and have a
Certificate of Inspection by March 16, 1998.
[CGD 82-004 and CGD 86-074, 62 FR 49321, Sept. 19, 1997]
Sec. 90.05-25 Seagoing barge.
(a) All nonself-propelled vessels of 100 gross tons and over that
proceed on voyages on the high seas or ocean are
[[Page 12]]
subject to inspection and certification as seagoing barges.
(b) In applying the laws and regulations to manned seagoing barges,
one criterion for invocation of safety standards is the description of
seagoing barges by relative size in gross tons. When it is determined by
the Commandant that the gross register tonnage for a particular manned
seagoing barge, which is attained by exemptions, reductions, or other
devices in the basic gross tonnage formulation, will circumvent or be
incompatible with the application of specific safety requirements in the
regulations in this subchapter for a manned seagoing barge of such
physical size, the Commandant shall prescribe the regulations to be made
applicable to such seagoing barge. When the Commandant determines that
the gross register tonnage is not a valid criterion for the invocation
of safety requirements based on relative size, the parties involved will
be informed of the determination and of the regulations applicable to
such manner seagoing barges, and before being permitted to operate such
seagoing barges, compliance therewith shall be required. Endorsements or
notations on the seagoing barge's certificate of inspection may be made
as appropriate.
Sec. 90.05-35 Flammable and combustible liquid cargo in bulk.
Note: Requirements for double hull construction for vessels carrying
oil, as defined in 33 CFR 157.03, in bulk as cargo are found in 33 CFR
157.10d.
Vessels inspected and certificated under this subchapter may carry
limited quantities of flammable and combustible liquid cargo in bulk in
the grades indicated, provided the Certificate of Inspection is endorsed
to permit such carriage:
(a) Cargo vessels:
(1) Grades D and E in an integral tank; and
(2) Grades D and E and certain specifically named Grade C in a
portable tank, including a marine portable tank (MPT), in accordance
with subpart 98.30 or 98.33 of this subchapter.
(b) Miscellaneous Vessels, such as cable, salvage, pile-driving, and
oil-drilling-rig vessels:
(1) Grades B, C, D, and E in a fixed independent or integral tank
authorized by the commandant;
(2) Grades D and E and certain specifically named Grade C in a
portable tank, including an MPT, in accordance with subpart 98.30 or
98.33 of this subchapter.
[CGD 84-043, 55 FR 37410, Sept. 11, 1990, as amended by CGD 90-051, 57
FR 362146, Aug. 12, 1992]
Subpart 90.10--Definition of Terms Used in This Subchapter
Sec. 90.10-1 Anniversary date.
The term anniversary date means the day and the month of each year,
which corresponds to the date of expiration of the Certificate of
Inspection.
[USCG 1999-4976, 65 FR 6501, Feb. 9, 2000]
Sec. 90.10-2 Approved.
This term means approved by the Commandant unless otherwise stated.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965. Redesignated by USCG 1999-4976,
65 FR 6501, Feb. 9, 2000]
Sec. 90.10-3 Barge.
This term means any nonself-propelled vessel.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965. Redesignated by USCG 1999-4976,
65 FR 6501, Feb. 9, 2000]
Sec. 90.10-5 Carrying freight for hire.
The carriage of any goods, wares, or merchandise or any other
freight for a valuable consideration whether directly or indirectly
flowing to the owner, charterer, operator, agent, or any other person
interested in the vessel.
Sec. 90.10-7 Commandant.
This term means the Commandant of the Coast Guard.
Sec. 90.10-9 Coast Guard District Commander.
This term means an officer of the Coast Guard designated as such by
the Commandant to command all Coast Guard activities within the
officer's district, which include the inspection, enforcement, and
administration of
[[Page 13]]
Subtitle II of Title 46, U.S. Code, Title 46 and Title 33 U.S. Code, and
regulations issued under these statutes.
[CGD 95-028, 62 FR 51205, Sept. 30, 1997]
Sec. 90.10-11 Coastwise.
Under this designation shall be included all vessels normally
navigating the waters of any ocean or the Gulf of Mexico 20 nautical
miles or less offshore.
Sec. 90.10-12 Gas free.
This term means free from dangerous concentrations of flammable or
toxic gases.
Sec. 90.10-13 Great Lakes.
Under this designation shall be included all vessels navigating the
Great Lakes.
Sec. 90.10-14 Headquarters.
This term means the Office of the Commandant, U.S. Coast Guard,
Washington, DC 20593-0001.
[CGFR 67-90, 33 FR 1015, Jan. 26, 1968, as amended by CGD 88-070, 53 FR
34534, Sept. 7, 1988]
Sec. 90.10-15 Industrial personnel.
This term means every person carried on board an industrial vessel
for the sole purpose of carrying out the industrial business or
functions of the industrial vessel. Examples of industrial personnel
include tradesmen, such as mechanics, plumbers, electricians, and
welders; laborers, such as wreckers and construction workers; and other
persons, such as supervisors, engineers, technicians, drilling
personnel, and divers.
[CGFR 67-90, 33 FR 1015, Jan. 26, 1968]
Sec. 90.10-16 Industrial vessel.
This term means every vessel which by reason of its special outfit,
purpose, design, or function engages in certain industrial ventures.
Included in this classification are such vessels as drill rigs, missile
range ships, dredges, cable layers, derrick barges, pipe lay barges,
construction and wrecking barges. Excluded from this classification are
vessels carrying freight for hire or engaged in oceanography, limnology,
or the fishing industry.
[CGFR 67-90, 33 FR 1015, Jan. 26, 1968]
Sec. 90.10-19 Lakes, bays, and sounds.
Under this designation shall be included all vessels navigating the
waters of any of the lakes, bays, or sounds other than the waters of the
Great Lakes.
Sec. 90.10-20 Liftboat.
Liftboat means an offshore supply vessel with moveable legs capable
of raising it's hull above the surface of the sea.
[CGD 82-004a, 55 FR 2525, Jan. 25, 1990]
Sec. 90.10-21 Marine inspector or inspector.
These terms mean any person from the civilian or military branch of
the Coast Guard assigned under the superintendence and direction of an
Officer in Charge, Marine Inspection, or any other person as may be
designated for the performance of duties with respect to inspection,
enforcement, and administration of Subtitle II of Title 46, U.S. Code,
Title 46 and Title 33 U.S. Code, and regulations issued under these
statutes.
[CGD 95-028, 62 FR 51205, Sept. 30, 1997]
Sec. 90.10-23 Motorboat.
This term means any vessel indicated in Column 5 of table 90.05-1(a)
65 feet in length or less which is propelled by machinery (including
steam). The length shall be measured from end to end over the deck
excluding sheer. This term includes a boat temporarily or permanently
equipped with a detachable motor. For the purpose of this subchapter,
motorboats are included under the term ``vessel'' unless specifically
noted otherwise. The various classes of motorboats are as follows:
Class A--Any motorboat less than 16 feet in length.
Class 1--Any motorboat 16 feet or over and less than 26 feet in length.
Class 2--Any motorboat 26 feet or over and less than 40 feet in length.
[[Page 14]]
Class 3--Any motorboat 40 feet or over and not more than 65 feet in
length.
[CGFR 65-50, 30 FR 16970, Dec. 30, 1965, as amended by CGD 95-028, 62 FR
51205, Sept. 30, 1997]
Sec. 90.10-25 Ocean.
Under this designation shall be included all vessels navigating the
waters of any ocean or the Gulf of Mexico more than 20 nautical miles
offshore.
Sec. 90.10-27 Officer in Charge, Marine Inspection (OCMI).
This term means any person from the civilian or military branch of
the Coast Guard designated as such by the Commandant and who, under the
superintendence and direction of the Coast Guard District Commander, is
in charge of an inspection zone for the performance of duties with
respect to the inspections, enforcement, and administration of Subtitle
II of Title 46, U.S. Code, Title 46 and Title 33 U.S. Code, and
regulations issued under these statutes.
[CGD 95-028, 62 FR 51205, Sept. 30, 1997]
Sec. 90.10-29 Passenger.
(a) The term passenger means--
(1) On an international voyage, every person other than--
(i) The master and the members of the crew or other persons employed
or engaged in any capacity on board a vessel on the business of that
vessel; and
(ii) A child under 1 year of age.
(2) On other than an international voyage, an individual carried on
the vessel, except--
(i) The owner or an individual representative of the owner or, in
the case of a vessel under charter, an individual charterer or
individual representative of the charterer;
(ii) The master; or
(iii) A member of the crew engaged in the business of the vessel who
has not contributed consideration for carriage and who is paid for
onboard services.
(b) The term passenger for hire means a passenger for whom
consideration is contributed as a condition of carriage on the vessel,
whether directly or indirectly flowing to the owner, charterer,
operator, agent, or any other person having an interest in the vessel.
[CGD 84-069, 61 FR 25288, May 20, 1996]
Sec. 90.10-30 Pilot boarding equipment and point of access.
(a) Pilot Boarding Equipment means a pilot ladder, accommodation
ladder, pilot hoist, or combination of them as required by this
subchapter.
(b) Point of Access means the place on deck of a vessel where a
person steps onto or off of pilot boarding equipment.
[CGD 79-032, 49 FR 25455, June 21, 1984]
Sec. 90.10-33 Rivers.
Under this designation shall be included all vessels whose
navigation is restricted to rivers and/or canals exclusively, and to
such other waters as may be so designated by the Coast Guard District
Commander.
Sec. 90.10-35 Recognized classification society.
The term recognized classification society means the American Bureau
of Shipping or other classification society recognized by the
Commandant.
Sec. 90.10-36 Seagoing barge.
A seagoing barge is a nonself-propelled vessel of at least 100 gross
tons making voyages beyond the Boundary Line (as defined in 46 CFR part
7). The phrase nonself-propelled vessel means a vessel without
sufficient means for self-propulsion and is required to be towed.
[CGFR 65-50, 30 FR 16970, Dec. 30, 1965, as amended by CGD 95-028, 62 FR
51206, Sept. 30, 1997]
Sec. 90.10-37 Vessel.
Where the word vessel is used in this subchapter, it shall be
considered to include all vessels indicated in Column 5 of Table 90.05-
1(a), except as otherwise noted in this subpart.
Sec. 90.10-38 Specially suitable for vehicles.
A space which is specially suitable for vehicles is one designed for
the carriage of automobiles or other self-propelled vehicles with
batteries connected and fuel tanks containing gasoline on vessels on
ocean or unlimited coastwise
[[Page 15]]
voyages. Requirements for the design and protection of spaces
``specially suitable for vehicles'' appear in subparts 92.15, 95.05,
95.15, 96.05, 97.36, 97.37, and 97.80 of this subchapter. In addition,
preparation of automobiles prior to carriage, with the exception of
disconnecting battery cables, must be in accordance with the applicable
provisions of 49 CFR 176.905.
[CGFR 66-33, 31 FR 15284, Dec. 5, 1966, as amended by CGD 86-033, 53 FR
36025, Sept. 16, 1988]
Sec. 90.10-40 Offshore supply vessels.
(a) An offshore supply vessel is a vessel that is propelled by
machinery other than steam, that is of 15 gross tons and less than 500
gross tons (as measured under the Standard, Dual, or Simplified
Measurement System under part 69, subpart C, D, or E, of this chapter)
or is less than 6,000 gross tons (as measured under the Convention
Measurement System under part 69, subpart B, of this chapter) and that
regularly carries goods, supplies or equipment in support of
exploration, exploitation, or production of offshore mineral or energy
resources.
(b) An existing offshore supply vessel is one contracted for, or the
keel of which was laid, before March 15, 1996.
(c) A new offshore supply vessel is one--
(1) That was contracted for, or the keel of which was laid, on or
after March 15, 1996; or
(2) That underwent a major conversion initiated on or after March
15, 1996.
[CGD 82-004 and CGD 86-074, 62 FR 49321, Sept. 19, 1997]
Sec. 90.10-42 Tankerman.
The following ratings are established in part 13 of this chapter.
The terms for the ratings identify persons holding valid merchant
mariners' documents for service in the ratings issued under that part:
(a) Tankerman-PIC.
(b) Tankerman-PIC (Barge).
(c) Restricted Tankerman-PIC.
(d) Restricted Tankerman-PIC (Barge)
(e) Tankerman-Assistant.
(f) Tankerman-Engineer.
[CGD 79-116, 60 FR 17157, Apr. 4, 1995]
Subpart 90.15--Equivalents
Sec. 90.15-1 Conditions under which equivalents may be used.
(a) Where in this subchapter it is provided that a particular
fitting, material, appliance, apparatus, or equipment, or type thereof,
shall be fitted or carried in a vessel, or that any particular provision
shall be made or arrangement shall be adopted, the Commandant may accept
in substitution therefor any other fitting, material, apparatus, or
equipment, or type thereof, or any other arrangement: Provided, That he
shall have been satisfied by suitable trials that the fitting, material,
appliance, apparatus, or equipment, or type thereof, or the provision or
arrangement is at least as effective as that specified in this
subchapter.
(b) In any case where it is shown to the satisfaction of the
Commandant that the use of any particular equipment, apparatus, or
arrangement not specifically required by law is unreasonable or
impracticable, the Commandant may permit the use of alternate equipment,
apparatus, or arrangement to such an extent and upon such conditions as
will insure, to his satisfaction, a degree of safety consistent with the
minimum standards set forth in this subchapter.
Subpart 90.20--General Marine Engineering Requirements
Sec. 90.20-1 Marine engineering details.
(a) All marine engineering details such as piping, valves, fittings,
boilers, pressure vessels, etc., and their appurtenances installed on
the vessel, shall be designed, constructed, and installed in accordance
with the provisions of subchapter F (Marine Engineering) of this
chapter.
Subpart 90.25--General Electrical Engineering Requirements
Sec. 90.25-1 Electrical engineering details.
(a) All electrical engineering details and installations shall be
designed and
[[Page 16]]
installed in accordance with subchapter J (Electrical Engineering) of
this chapter.
Subpart 90.27--Lifesaving Appliances and Arrangements
Sec. 90.27-1 Lifesaving appliances and arrangements.
All lifesaving appliances and arrangements must be in accordance
with subchapter W (Lifesaving Appliances and Arrangements) of this
chapter.
[CGD 84-069, 61 FR 25288, May 20, 1996]
Subpart 90.35--American Bureau of Shipping's Standards
Sec. 90.35-1 Standards to be used.
(a) Where in this subchapter an item, or method of construction, or
testing is required to meet the standards established by the American
Bureau of Shipping, the current standards in effect at the time of
construction of the vessel, or otherwise as applicable, shall be used.
The current standards of other recognized classification societies may
also be accepted upon approval by the Commandant.
Sec. 90.35-5 Where obtainable.
(a) The standards established by the American Bureau of Shipping are
usually published annually and may be purchased from the American Bureau
of Shipping, ABS Plaza, 16855 Northchase Drive, Houston, TX 77060. These
standards may be also examined at the Office of the Commandant (G--M),
U.S. Coast Guard, Washington, DC 20593-0001, or at the Office of any
Coast Guard District Commander or Officer in Charge, Marine Inspection.
[CGFR 65-50, 30 FR 1697, Dec. 30, 1965, as amended by CGFR 68-32, 33 FR
5718, Apr. 12, 1968; CGD 88-070, 53 FR 34534, Sept. 7, 1988; CGD 88-070,
53 FR 37570, Sept. 27, 1988; CGD 88-070, 53 FR 44011, Nov. 1, 1988; CGD
95-072, 60 FR 50464, Sept. 29, 1995; 60 FR 54106, Oct. 19, 1995; USCG-
2000-7790, 65 FR 58461, Sept. 29, 2000]
PART 91--INSPECTION AND CERTIFICATION--Table of Contents
Subpart 91.01--Certificate of Inspection
Sec.
91.01-1 When required.
91.01-5 Posting.
91.01-10 Period of validity for a Certificate of Inspection.
91.01-15 Temporary certificate.
91.01-20 Expired certificate.
91.01-25 Emergency carriage of more than 16 persons in addition to the
crew on vessels not engaged in international voyages.
Subpart 91.05--Permit to Proceed to Another Port for Repair
91.05-1 When issued.
91.05-5 To whom issued.
91.05-10 Conditions of permit.
91.05-15 Posting.
Subpart 91.15--Inspection of Vessels
91.15-1 Standards in inspection of hulls, boilers, and machinery.
91.15-5 Alternate compliance.
Subpart 91.20--Initial Inspection
91.20-1 Prerequisite of certificate of inspection.
91.20-5 When made.
91.20-10 Plans.
91.20-15 Scope of inspection.
91.20-20 Specific tests and inspections.
Subpart 91.25--Inspection for Certification
91.25-1 Prerequisite of reissuance of certificate of inspection.
91.25-5 Application for a Certificate of Inspection.
91.25-10 Scope of inspection.
91.25-15 Lifesaving equipment.
91.25-20 Fire-extinguishing equipment.
91.25-25 Hull equipment.
91.25-30 Electrical engineering equipment.
91.25-35 Marine engineering equipment.
91.25-37 Tanks containing dangerous cargoes.
91.25-38 Pollution prevention.
91.25-40 Sanitary inspection.
91.25-45 Fire hazards.
91.25-50 Inspector not limited.
Subpart 91.27--Annual and Periodic Inspections
91.27-1 Annual and periodic inspections.
91.27-5 Certificate of Inspection: Conditions of validity.
91.27-13 Alternative annual inspection for offshore supply vessels less
than 400 gross tons in foreign ports.
[[Page 17]]
91.27-15 Inspectors not limited.
Subpart 91.30--Inspection After Accident
91.30-1 General or partial survey.
Subpart 91.35--Sanitary Inspections
91.35-1 When made.
Subpart 91.40--Drydocking
91.40-1 Definitions relating to hull examinations.
91.40-3 Drydock examination, internal structural examination, cargo
tank internal examination, and underwater survey intervals.
91.40-5 Notice and plans required.
Subpart 91.43-- Integral Fuel Oil Tank Examinations
91.43-1 When required.
Subpart 91.45--Repairs and Alterations
91.45-1 Notice required.
91.45-5 Inspection required.
Subpart 91.50--Special Operating Requirements
91.50-1 Inspection and testing required when making alterations,
repairs, or other such operations involving riveting, welding,
burning or like fire-producing actions.
Subpart 91.55--Plan Approval
91.55-1 General.
91.55-5 Plans and specifications required for new construction.
91.55-10 Plans required for alterations of existing vessels.
91.55-15 Procedure for submittal of plans.
91.55-20 Number of plans required.
Subpart 91.60--Certificates Under International Convention for Safety of
Life at Sea, 1974
91.60-1 Application.
91.60-5 Cargo Ship Safety Construction Certificate.
91.60-10 Cargo Ship Safety Equipment Certificate.
91.60-15 Cargo Ship Safety Radio Certificate.
91.60-25 Exemption Certificate.
91.60-30 Safety Management Certificate.
91.60-35 Availability of Certificates.
91.60-40 Duration of Convention certificates.
91.60-45 American Bureau of Shipping.
Authority: 33 U.S.C. 1321(j); 46 U.S.C. 3205, 3306, 3307; E.O.
12234; 45 FR 58801; 3 CFR, 1980 Comp., p. 277; E.O. 12777, 56 FR 54757,
3 CFR, 1991 Comp., p. 351; 49 CFR 1.46.
Source: CGFR 65-50, 30 FR 16974, Dec. 30, 1965, unless otherwise
noted.
Subpart 91.01--Certificate of Inspection
Sec. 91.01-1 When required.
(a) Except as noted in this subpart or subpart 91.05, no vessel
subject to inspection and certification shall be operated without a
valid certificate of inspection.
Sec. 91.01-5 Posting.
(a) On vessels of over 25 gross tons, the original certificate of
inspection shall, in general, be framed under glass and posted in a
conspicuous place where it will be most likely to be observed. On
vessels not over 25 gross tons, and on other vessels such as barges,
where the framing of the certificate under glass would be impracticable,
the original certificate of inspection shall be kept on board to be
shown on demand.
Sec. 91.01-10 Period of validity for a Certificate of Inspection.
(a) Certificates of inspection will be issued for a period of 5
years. Application may be made by the master, owner, or agent for
inspection and issuance of a new certificate of inspection at any time
during the period of validity of the current certificate.
(b) Certificates of inspection may be revoked or suspended by the
Coast Guard where such process is authorized by law. This may occur if
the vessel does not meet the requirements of law or regulations in this
chapter or if there is a failure to maintain the safety requirements
requisite to the issuance of a certificate of inspection.
(c)(1) In the case of the following vessels, modification of the
period of validity of the certificate of inspection will be permitted as
set forth in this paragraph:
(i) Nonself-propelled vessels of 100 gross tons and over proceeding
on the high seas or ocean for the sole purpose of changing place of
employment.
(ii) Nonself-propelled vessels of 100 gross tons and over making
rare or infrequent voyages on the high seas or
[[Page 18]]
ocean and returning to the port of departure.
(2) The certificate of inspection may be issued for a specific
period of time to cover a described situation or for one voyage only but
in no case to exceed 5 years. The certificate of inspection will include
the conditions under which the vessel must operate. Unless the vessel is
in compliance with this Subchapter insofar as it applies to seagoing
barges of 100 gross tons and over, such vessel shall not carry any
person on board while underway, and the certificate of inspection will
be endorsed as an unmanned seagoing barge.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGFR 68-82, 33 FR
18901, Dec. 18, 1968; CGD 95-012, 60 FR 48051, Sept. 18, 1995; USCG
1999-4976, 65 FR 6501, Feb. 9, 2000]
Sec. 91.01-15 Temporary certificate.
(a) If necessary to prevent delay of the vessel, a temporary
certificate of inspection, Form CG-854, shall be issued pending the
issuance and delivery of the regular certificate of inspection. Such
temporary certificate shall be carried in the same manner as the regular
certificate and shall in all ways be considered the same as the regular
certificate of inspection which it represents.
Sec. 91.01-20 Expired certificate.
(a) Nothing in this subpart shall prevent a vessel upon a regularly
established line from a port in the United States to a port of a foreign
country not contiguous to the United States whose certificate of
inspection expires at sea or while said vessel is in a foreign port or a
port of Hawaii from lawfully completing her voyage without the valid
certificate of inspection or temporary certificate required by this
subpart: Provided, That the certificate of inspection did not expire
within 15 days after the vessel left the last port of the United States,
and that the voyage shall be completed within 30 days after the
expiration of the certificate of inspection.
Sec. 91.01-25 Emergency carriage of more than 16 persons in addition to the crew on vessels not engaged in international voyages.
(a) When a District Commander finds that an emergency situation
exists, he authorizes the local Officer in Charge, Marine Inspection, to
issue amendments to vessels' certificates of inspection authorizing the
carriage of more than 16 persons in addition to the crew.
(b) Upon receipt of an application from a vessel's owner or
operator, the Local Officer in Charge, Marine Inspection, amends the
vessel's certificate of inspection after--
(1) Additional lifesaving and firefighting equipment found necessary
by the OCMI has been provided;
(2) A stability evaluation has been performed; and
(3) Any other conditions considered necessary by the OCMI have been
satisfied.
[CGD 76-004, 41 FR 32744, Aug. 5, 1976]
Subpart 91.05--Permit To Proceed to Another Port for Repair
Sec. 91.05-1 When issued.
(a) The Officer in Charge, Marine Inspection, may issue a permit to
proceed to another port for repair, Form CG-948 to a vessel, if in his
judgment it can be done with safety, even if the certificate of
inspection of the vessel has expired or is about to expire.
Sec. 91.05-5 To whom issued.
(a) Such permit will only be issued upon the written application of
the master, owner, or agent of the vessel.
Sec. 91.05-10 Conditions of permit.
(a) The permit will state upon its face the conditions under which
it is issued and whether or not the vessel is permitted to carry freight
or passengers.
Sec. 91.05-15 Posting.
(a) The permit shall be carried in a manner similar to that
described in Sec. 91.01-5 for a certificate of inspection.
[[Page 19]]
Subpart 91.15--Inspection of Vessels
Sec. 91.15-1 Standards in inspection of hulls, boilers, and machinery.
In the inspection of hulls, boilers, and machinery of vessels, the
standards established by the American Bureau of Shipping, see part 90,
subpart 90.35 of this chapter, respecting material and inspection of
hulls, boilers, and machinery, and the certificate of classification
referring thereto, except where otherwise provided for by the rules and
regulations in this subchapter, subchapter E (Load Lines), subchapter F
(Marine Engineering), subchapter J (Electrical Engineering), and
subchapter W (Lifesaving Appliances and Arrangements) of this chapter,
shall be accepted as standard by the inspectors.
[CGD 84-069, 61 FR 25289, May 20, 1996]
Sec. 91.15-5 Alternate compliance.
(a) In place of compliance with other applicable provisions of this
subchapter, the owner or operator of a vessel subject to plan review and
inspection under this subchapter for initial issuance or renewal of a
Certificate of Inspection may comply with the Alternate Compliance
Program provisions of part 8 of this chapter.
(b) For the purposes of this section, a list of authorized
classification societies, including information for ordering copies of
approved classification society rules and supplements, is available from
Commandant (G-MSE), 2100 Second St., SW., Washington, DC 20593-0001;
telephone (202)267-6925; or fax (202)267-4816. Approved classification
society rules and supplements are incorporated by reference into 46 CFR
8.110(b).
[CGD 95-010, 62 FR 67536, Dec. 24, 1997, as amended by USCG-1999-5004,
64 FR 30439, June 8, 1999]
Subpart 91.20--Initial Inspection
Sec. 91.20-1 Prerequisite of certificate of inspection.
(a) The initial inspection is a prerequisite of the issuance of the
original certificate of inspection.
Sec. 91.20-5 When made.
(a) The original inspection will only be made upon the written
application of the owner or builder of the vessel to the Officer in
Charge, Marine Inspection, on Form CG-3752, Application for Inspection
of U.S. Vessel, at or nearest the port where the vessel is located.
Sec. 91.20-10 Plans.
(a) Before application for inspection is made, and before
construction is started, the owner or builder shall have plans approved
by the Commandant indicating the proposed arrangement and construction
of the vessel. The procedure for submitting plans and the list of plans
to be supplied is set forth in subpart 91.55.
Sec. 91.20-15 Scope of inspection.
(a) The initial inspection, which may consist of a series of
inspections during the construction of a vessel, shall include a
complete inspection of the structure, including the outside of the
vessel's bottom, the machinery, unfired pressure vessels, equipment and
the inside and outside of the boilers. The inspection shall be such as
to insure that the arrangements, material, and scantlings of the
structure, boilers, and other pressure vessels and their appurtenances,
piping, main and auxiliary machinery, electrical installations,
lifesaving appliances, fire-detecting and extinguishing equipment, pilot
boarding equipment, pollution prevention equipment, and other equipment
fully comply with the applicable regulations for such vessel and are in
accordance with approved plans, and determine that the vessel is in
possession of a valid certificate issued by the Federal Communications
Commission, if any. The inspection shall be such as to ensure that the
workmanship of all parts of the vessel and its equipment is in all
respects satisfactory and that the vessel is provided with lights, means
of making sound signals, and distress signals as required by applicable
statutes and regulations.
(b) When equipment is installed which is not required by applicable
regulations in this subchapter, that equipment shall be inspected and
tested as
[[Page 20]]
required for such equipment by applicable regulations in subchapter H
(Passenger Vessels) of this chapter. For example, fire-detecting systems
shall be inspected and tested as required by subpart 71.20 of subchapter
H (Passenger Vessels) of this chapter.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGFR 68-32, 33 FR
5718, Apr. 12, 1968; CGFR 68-82, 33 FR 18901, Dec. 18, 1968; CGD 71-
161R, 37 FR 28262, Dec. 21, 1972; CGD 82-036, 48 FR 654, Jan. 6, 1983;
CGD 79-032, 49 FR 25455, June 21, 1984; CGD 95-012, 60 FR 48051, Sept.
18, 1995]
Sec. 91.20-20 Specific tests and inspections.
The applicable tests and inspections as set forth in subpart 91.25
of this part shall be made at this time. In addition, the following
specific tests and inspections shall be made by the inspector.
(a) For inspection procedures of lifesaving appliances and
arrangements, see subchapter W (Lifesaving Appliances and Arrangements)
of this chapter.
(b) Installation of carbon dioxide extinguishing piping--see
Sec. 95.15-15 of this subchapter.
(c) For inspection procedures of marine engineering equipment and
systems, see subchapter F (Marine Engineering) of this chapter.
(d) For inspection procedures of Electrical Engineering equipment
and systems, see subchapter J (Electrical Engineering) of this chapter.
(e) For inspection and tests of tanks containing certain dangerous
cargoes in bulk, see part 98 of this subchapter.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 84-069, 61 FR
25289, May 20, 1996]
Subpart 91.25--Inspection for Certification
Sec. 91.25-1 Prerequisite of reissuance of certificate of inspection.
(a) An inspection for certification is a prerequisite of the
reissuance of a certificate of inspection.
Sec. 91.25-5 Application for a Certificate of Inspection.
You must submit a written application for an inspection for
certification to the cognizant Officer in Charge, Marine Inspection. To
renew a Certificate of Inspection, you must submit an application at
least 30 days before the expiration of the tank vessel's current
certificate. You must use Form CG-3752, Application for Inspection of
U.S. Vessel, and submit it to the Officer in Charge, Marine Inspection
at, or nearest to, the port where the vessel is located. When renewing a
Certificate of Inspection, you must schedule an inspection for
certification within the 3 months before the expiration date of the
current Certificate of Inspection.
[USCG 1999-4976, 65 FR 6501, Feb. 9, 2000]
Sec. 91.25-10 Scope of inspection.
The inspection for certification shall include an inspection of the
structure, boilers, and other pressure vessels, machinery, and
equipment. The inspection shall be such as to insure that the vessel, as
regards the structure, boilers and other pressure vessels, and their
appurtenances, piping, main and auxiliary machinery, electrical
installations, lifesaving appliances, fire-detecting and extinguishing
equipment, pilot boarding equipment, pollution prevention equipment, and
other equipment, is in satisfactory condition and fit for the service
for which it is intended, and that it complies with the applicable
regulations for such vessel and determine that the vessel is in
possession of a valid certificate issued by the Federal Communications
Commission, if required. The lights, means of making sound signals, and
distress signals carried by the vessel shall also be subject to the
above mentioned inspection for the purpose of ensuring that they comply
with the requirements of the applicable statutes and regulations.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGFR 68-32, 33 FR
5718, Apr. 12, 1968; CGFR 68-82, 33 FR 18901, Dec. 18, 1968; CGD 71-
161R, 37 FR 28262, Dec. 21, 1972; CGD 82-036, 48 FR 655, Jan. 6, 1983;
CGD 79-032, 49 FR 25455, June 21, 1984; CGD 95-012, 60 FR 48051, Sept.
18, 1995]
Sec. 91.25-15 Lifesaving equipment.
For inspection procedures of Lifesaving appliances and arrangements,
[[Page 21]]
see subchapter W (Lifesaving Appliances and Arrangements) of this
chapter.
[CGD 84-069, 61 FR 25289, May 20, 1996]
Sec. 91.25-20 Fire-extinguishing equipment.
(a) At each inspection for certification, periodic inspection and at
other times necessary, the inspector will determine that all fire-
extinguishing equipment is in suitable condition and may require any
tests necessary to determine the condition of the equipment. The
inspector will determine if the tests and inspections required by
Sec. 97.15-60 of this subchapter have been conducted. At each inspection
for certification and periodic inspection, the inspector will check
fire-extinguishing equipment with the following tests and inspections:
(1) All hand portable fire extinguishers and semi-portable fire
extinguishing systems shall be checked as noted in Table 91.25-20(a)(1).
In addition, the hand portable fire extinguishers and semi-portable fire
extinguishing systems shall be examined for excessive corrosion and
general condition.
Table 91.25-20(a)(1)
------------------------------------------------------------------------
Type unit Test
------------------------------------------------------------------------
Soda acid................................ Discharge. Clean hose and
inside of extinguisher
thoroughly. Recharge.
Foam..................................... Discharge. Clean hose and
inside of extinguisher
thoroughly. Recharge.
Pump tank (water or antifreeze).......... Discharge. Clean hose and
inside of extinguisher
thoroughly. Recharge with
clean water or antifreeze.
Cartridge operated (water, antifreeze or Examine pressure cartridge
loaded stream). and replace if end is
punctured or if cartridge is
otherwise determined to have
leaked or to be in
unsuitable condition. Remove
liquid. Clean hose and
inside of extinguisher
thoroughly. Recharge with
clean water, solution, or
antifreeze. Insert charged
cartridge.
Carbon Dioxide........................... Weigh cylinders. Recharge if
weight loss exceeds 10
percent of weight of charge.
Inspect hose and nozzle to
be sure they are clear. 1
Dry chemical (cartridge-operated type)... Examine pressure cartridge
and replace if end is
punctured or if cartridge is
otherwise determined to have
leaked or to be in
unsuitable condition.
Inspect hose and nozzle to
see they are clear. Insert
charged cartridge. Be sure
dry chemical is free-flowing
(not caked) and chamber
contains full charge.
Dry chemical (stored pressure type)...... See that pressure gage is in
operating range. If not, or
if seal is broken, weigh or
otherwise determine that
full charge of dry chemical
is in extinguisher. Recharge
if pressure is low or if dry
chemical is needed.
Vaporizing liquid \2\ (pump type)........ Pump a few strokes into clean
pail and replace liquid.
Keep water out of
extinguisher or liquid. Keep
extinguisher completely full
of liquid.
Vaporizing liquid \2\ (stored pressure See that pressure gage is in
type). operating range. Weigh or
check liquid level to
determine that full charge
of liquid is in
extinguisher. Recharge if
pressure is low or if liquid
is needed.
------------------------------------------------------------------------
\1\ Cylinders must be tested and marked, and all flexible connections
and discharge hoses of semi-portable carbon dioxide and halon
extinguishers must be tested or renewed, as required by Secs. 147.60
and 147.65 of this chapter.
\2\ Vaporizing-liquid type fire extinguishers containing carbon
tetrachloride or chlorobromomethane or other toxic vaporizing liquids
shall be removed from all vessels. (See Sec. 95.50-5(e) of this
subchapter.)
(2) Fixed fire-extinguishing systems shall be checked as noted in
Table 91.25-20(a)(2). In addition, all parts of the fixed fire-
extinguishing systems, shall be examined for excessive corrosion and
general conditions.
Table 91.25-20(a)(2)
------------------------------------------------------------------------
Type system Test
------------------------------------------------------------------------
Foam..................................... Systems utilizing a soda
solution shall have such
solution replaced. In all
cases, ascertain that powder
is not caked.
Carbon dioxide........................... Weigh cylinders. Recharge if
weight loss exceeds 10
percent of weight of charge.
\1\
------------------------------------------------------------------------
\1\ Cylinders must be tested and marked, and all flexible connections on
fixed carbon dioxide systems must be tested or renewed, as required by
Secs. 147.60 and 147.65 of this chapter.
(3) On all fire-extinguishing systems, all piping controls, valves,
and alarms shall be checked to ascertain that the system is in operating
condition. In this respect steam smothering lines shall be checked with
at least a 50 p.s.i. air pressure with the ends capped or by blowing
steam through the lines at the designed pressure.
[[Page 22]]
(4) The fire main system shall be operated and the pressure checked
at the most remote and highest outlets. All firehose shall be subjected
to a test pressure equivalent to the maximum pressure to which they may
be subjected in service, but not less than 100 p.s.i.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGFR 68-32, 33 FR
5718, Apr. 18, 1968; CGD 78-154, 44 FR 13491, Mar. 12, 1979; CGD 84-044,
53 FR 7748, Mar. 10, 1988; USCG 1999-4976, 65 FR 6501, Feb. 9, 2000; 65
FR 11904, Mar. 7, 2000]
Sec. 91.25-25 Hull equipment.
(a) At each inspection for certification and periodic inspection,
the inspectors shall conduct the following tests and inspections of hull
equipment:
(1) All watertight doors shall be operated locally by manual power
and also by hydraulic or electric power if so fitted. Where remote
control is fitted, the doors shall also be operated by the remote
control apparatus.
(2) The remote controls of all valves shall be operated.
(3) The owner, operator or master shall provide the Officer in
Charge, Marine Inspection with all current valid certificates and
registers of cargo gear issued by an organization recognized by the
Commandant under Sec. 31.10-16.
(b) Every acceptable cargo gear certificate and/or register shall be
properly executed by a person authorized to do so and shall:
(1) Certify as to the tests and examinations conducted;
(2) Show the dates on which the tests and examinations were
conducted; and
(3) Indicate that the cargo gear described in the certificate or
register complies with the standards of the organization or association
authorized to issue the certificate or register.
(c) Competent persons for the purposes of this section are defined
as--
(1) Surveyors of a classification society recognized by the
Commandant under 46 U.S.C. 3316.
(2) Surveyors of a cargo gear organization recognized by the
Commandant under Sec. 31.10-16.
(3) Responsible officials or employees of the testing laboratories,
companies, or organizations who conduct tests of pieces of loose cargo
gear, wire rope, or the annealing of gear as may be required by the
standards of the organization or association authorized to issue the
certificate or register.
(d) The registers issued in connection with cargo gear certification
must have all required entries fully completed as of the dates
indicated, shall be kept current, and shall include the following:
(1) A register of the cargo handling machinery and the gear
accessory thereto carried on the vessel named therein;
(2) Certification of the testing and examination of winches,
derricks, and their accessory gear;
(3) Certification of the testing and examination of cranes, hoists,
and their accessory gear;
(4) Certification of the testing and examination of chains, rings,
hooks, shackles, swivels, and blocks;
(5) Certification of the testing and examination of wire rope;
(6) Certification of the heat-treatment of chains, rings, hooks,
shackles, and swivels which require such treatment; and,
(7) Certification of the annual thorough examinations of gear not
required to be periodically heat-treated.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 95-028, 62 FR
51206, Sept. 30, 1997; USCG 1999-4976, 65 FR 6501, Feb. 9, 2000]
Sec. 91.25-30 Electrical engineering equipment.
For inspection procedures of electrical engineering equipment and
systems see subchapter J (Electrical Engineering) of this chapter.
Sec. 91.25-35 Marine engineering equipment.
(a) For inspection procedures of marine engineering equipment and
systems, see subchapter F (Marine Engineering) of this chapter.
Sec. 91.25-37 Tanks containing dangerous cargoes.
(a) For inspection and tests of tanks containing certain dangerous
cargoes in bulk, see part 98 of this subchapter.
[[Page 23]]
Sec. 91.25-38 Pollution prevention.
At each inspection for certification and periodic inspection, the
inspector shall examine the vessel to determine that it meets the vessel
design and equipment requirements for pollution prevention in 33 CFR
part 155, subpart B.
[CGD 71-161R, 37 FR 28262, Dec. 21, 1972, as amended by USCG 1999-4976,
65 FR 6501, Feb. 9, 2000]
Sec. 91.25-40 Sanitary inspection.
(a) At each inspection for certification and periodic inspection,
the quarters, toilets, and washing spaces, galleys, serving pantries,
lockers, etc., shall be examined by the inspector to be assured that
they are in a sanitary condition.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by USCG 1999-4976,
65 FR 6501, Feb. 9, 2000]
Sec. 91.25-45 Fire hazards.
(a) At each inspection for certification and periodic inspection,
the inspector shall examine the tank tops and bilges in the machinery
spaces to see that there is no accumulation of oil which might create a
fire hazard.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by USCG 1999-4976,
65 FR 6501, Feb. 9, 2000]
Sec. 91.25-50 Inspector not limited.
(a) Nothing in this subpart shall be construed as limiting the
inspector from making such tests or inspections as he deems necessary to
be assured of the safety and seaworthiness of the vessel.
Subpart 91.27--Annual and Periodic Inspections
Sec. 91.27-1 Annual and periodic inspections.
(a) Annual inspection. Your vessel must undergo an annual inspection
within the 3 months before or after each anniversary date, except as
required in paragraph (b) of this section.
(1) You must contact the cognizant Officer in Charge, Marine
Inspection to schedule an inspection at a time and place which he or she
approves. No written application is required.
(2) The scope of the annual inspection is the same as the inspection
for certification as specified in Sec. 91.25-10 but in less detail
unless the cognizant marine inspector finds deficiencies or determines
that a major change has occurred since the last inspection. If
deficiencies are found or a major change to the vessel has occurred, the
marine inspector will conduct an inspection more detailed in scope to
ensure that the vessel is in satisfactory condition and fit for the
service for which it is intended. If your vessel passes the annual
inspection, the marine inspector will endorse your current Certificate
of Inspection.
(3) If the annual inspection reveals deficiencies in your vessel's
maintenance, you must make any or all repairs or improvements within the
time period specified by the Officer in Charge, Marine Inspection.
(4) Nothing in this subpart limits the marine inspector from
conducting such tests or inspections he or she deems necessary to be
assured of the vessel's seaworthiness.
(b) Periodic inspection. Your vessel must undergo a periodic
inspection within 3 months before or after the second or third
anniversary of the date of your vessel's Certificate of Inspection. This
periodic inspection will take the place of an annual inspection.
(1) You must contact the cognizant Officer in Charge, Marine
Inspection to schedule an inspection at a time and place which he or she
approves. No written application is required.
(2) The scope of the periodic inspection is the same as that for the
inspection for certification, as specified in Sec. 91.25-10. The Officer
in Charge, Marine Inspection will insure that the vessel is in
satisfactory condition and fit for the service for which it is intended.
If your vessel passes the periodic inspection, the marine inspector will
endorse your current Certificate of Inspection.
(3) If the periodic inspection reveals deficiencies in your vessel's
maintenance, you must make any or all repairs or improvements within the
time period specified by the Officer in Charge, Marine Inspection.
[[Page 24]]
(4) Nothing in this subpart limits the marine inspector from
conducting such tests or inspections he or she deems necessary to be
assured of the vessel's seaworthiness.
[USCG 1999-4976, 65 FR 6501, Feb. 9, 2000]
Sec. 91.27-5 Certificate of Inspection: Conditions of validity.
To maintain a valid Certificate of Inspection, you must complete
your annual and periodic inspections within the periods specified in
Sec. 91.27-1 (a) and (b) and your Certificate of Inspection must be
endorsed.
[USCG 1999-4976, 65 FR 6502, Feb. 9, 2000]
Sec. 91.27-13 Alternative annual inspection for offshore supply vessels less than 400 gross tons in foreign ports.
(a) The owner or operator of an offshore supply vessel of less than
400 gross tons, except liftboats as defined in Sec. 90.10-20 of this
chapter, may request authorization to conduct an alternative annual
inspection in place of the annual inspection described in Sec. 91.27-
1(a) of this chapter. You must submit your request to the Officer in
Charge, Marine Inspection responsible for conducting inspections in the
country in which the vessel is operating and will be examined. To
qualify for the alternative annual inspection, you must meet the
following requirements:
(1) The request for authorization must be in writing and received by
the cognizant Officer in Charge, Marine Inspection before the end of the
twelfth month of each COI anniversary year.
(2) The vessel is expected to be continuously employed outside of
the United States during the 3 months before and after each anniversary
date of the issuance of the COI.
(b) In determining whether to grant authorization for the
alternative annual inspection, the Officer in Charge, Marine Inspection
will consider the following:
(1) Information contained in previous inspection and drydock
examination reports, including the Officer in Charge, Marine
Inspection's recommendation for participation in the alternative
midperiod examination program, and the alternative annual inspection
program.
(2) The nature, number, and severity of any marine casualties or
accidents, as defined in Sec. 4.03-1 of this chapter, which the vessel
has experienced in the last 3 years.
(3) The nature, number, and severity of any outstanding inspection
requirements for the vessel.
(4) The owner or operator's history of compliance and cooperation in
the alternative midperiod examination program and the alternative annual
inspection program, which includes--
(i) The prompt correction of deficiencies;
(ii) The reliability of previously submitted alternative examination
and annual inspection reports; and
(iii) The reliability of representations that the vessel under
consideration will be, and other vessels previously examined under this
section were, employed outside of the United States for the 3 month
period before and after each anniversary date.
(c) If authorization is granted, the Officer in Charge, Marine
Inspection must provide the applicant written authorization to proceed
with the alternative annual inspection, including special instructions
when appropriate.
(d) The following conditions must be met for the alternative annual
inspection to be accepted by the Coast Guard in lieu of conducting an
annual inspection in accordance with Sec. 91.27-1(a) of this subpart.
(1) The alternative annual inspection must be conducted within 3
months before and after each anniversary date.
(2) The alternative annual inspection must be of the scope detailed
in Sec. 91.27-1(a) of this subpart and must be conducted by the vessel's
master, operator, or a designated representative of the owner or
operator.
(3) Upon completion of the alternative annual inspection, the person
or persons conducting the inspection must prepare a comprehensive report
describing the conditions found. This inspection report must contain
sufficient detail to allow an evaluation to be made by the Officer in
Charge, Marine Inspection to whom the report is submitted that the
vessel is fit for the service and route specified on the Certificate of
Inspection. The report must
[[Page 25]]
include reports and receipts documenting the servicing of lifesaving and
fire protection equipment, and any photographs or sketches necessary to
clarify unusual circumstances. Each person preparing the report must
sign it and certify that the information contained therein is complete
and accurate.
(4) Unless the vessel's master participated in the alternative
annual inspection and the preparation of the inspection report, the
master must review the report for completeness and accuracy. The master
must sign the report to indicate review and forward it to the vessel's
owner or operator who requested authorization to conduct the inspection.
(5) The owner or operator of an offshore supply vessel inspected
under this subpart must review and submit the report required by
paragraph (d)(3) of this section to the Officer in Charge, Marine
Inspection who authorized the owner or operator to conduct the
alternative annual inspection. The inspection report must be received by
the cognizant Officer in Charge, Marine Inspection before the first day
of the fifth month following the anniversary date. The forwarding letter
or endorsement must be certified and contain the following information--
(i) That the person or persons who conducted the inspection acted on
behalf of the vessel's owner or operator;
(ii) That the inspection report was reviewed by the owner or
operator;
(iii) That the discrepancies noted during the inspection have been
corrected or will be corrected within a stated time frame; and
(iv) That the owner or operator has sufficient personal knowledge of
conditions aboard the vessel at the time of the inspection or has made
necessary inquiries to justify forming a belief that the inspection
report is true and correct.
(e) The form of certification required under this subpart is as
follows:
I certify that the above is true and complete to the best of my
knowledge and belief.
(f) Deficiencies and hazards discovered during an alternative annual
inspection conducted pursuant to this section must be corrected or
eliminated, if practical, before the inspection report is submitted to
the Officer in Charge, Marine Inspection in accordance with paragraph
(d)(5) of this section. Deficiencies and hazards that are not corrected
or eliminated by the time the inspection report is submitted must be
listed in the report as ``outstanding.'' Upon receipt of an inspection
report indicating outstanding deficiencies or hazards, the Officer in
Charge, Marine Inspection will inform the owner or operator of the
vessel in writing of the time period in which to correct or eliminate
the deficiencies or hazards and the method for establishing that the
corrections have been accomplished. Where a deficiency or hazard remains
uncorrected or uneliminated after the expiration of the time specified
for correction or elimination, the Officer in Charge, Marine Inspection
will initiate appropriate enforcement measures.
(g) Upon receipt of the report required by paragraph (d)(3) of this
section, the Officer in Charge, Marine Inspection must evaluate it and
make the following determination:
(1) Whether the alternative annual inspection is accepted in lieu of
the annual inspection required by Sec. 91.27-1(a) of this subpart.
(2) Whether the vessel is in satisfactory condition.
(3) Whether the vessel continues to be reasonably fit for its
intended service and route. The Officer in Charge, Marine Inspection may
request any additional information needed to make the determinations
required by this section. The Officer in Charge, Marine Inspection will
inform the owner or operator in writing of the determinations required
by this section.
(h) If the Officer in Charge, Marine Inspection determines, in
accordance with paragraph (g) of this section, that the alternative
annual inspection is not accepted in lieu of the annual inspection
required by Sec. 91.27-1(a) of this subpart, the vessel must be
reinspected by the cognizant Officer in Charge, Marine Inspection as
soon as practical.
(i) If the Officer in Charge, Marine Inspection determines, in
accordance with paragraph (g) of this section, that the alternative
annual inspection is accepted in lieu of the annual inspection
[[Page 26]]
required by Sec. 91.27-1(a) of this subpart, the master must complete
the applicable COI endorsement.
[USCG 1999-4976, 65 FR 6502, Feb. 9, 2000; 65 FR 11904, Mar. 7, 2000]
Sec. 91.27-15 Inspectors not limited.
(a) Nothing in this subpart shall be construed as limiting the
inspector from making such tests or inspections as he deems necessary to
be assured of the seaworthiness of the vessel.
Subpart 91.30--Inspection After Accident
Sec. 91.30-1 General or partial survey.
(a) A survey, either general or partial, according to the
circumstances, shall be made every time an accident occurs or a defect
is discovered which affects the safety of the vessel or the efficacy or
completeness of its lifesaving appliances, fire-fighting or other
equipment, or whenever any important repairs or renewals are made. The
survey shall be such as to insure that the necessary repairs or renewals
have been effectively made, that the material and the workmanship of
such repairs or renewals are in all respects satisfactory, and that the
vessel complies in all respects with the regulations in this subchapter.
Subpart 91.35--Sanitary Inspections
Sec. 91.35-1 When made.
(a) An inspection of quarters, toilet and washing spaces, serving
pantries, galleys, etc., shall be made at least once in every month. If
the route of the vessel is such that it is away from a United States
port for more than one month, an inspection shall be conducted at least
once every trip.
Subpart 91.40--Drydocking
Sec. 91.40-1 Definitions relating to hull examinations.
As used in this part--
(a) Drydock examination means hauling out a vessel or placing a
vessel in a drydock or slipway for an examination of all accessible
parts of the vessel's underwater body and all through-hull fittings.
(b) Internal structural examination means an examination of the
vessel while afloat or in drydock and consists of a complete examination
of the vessel's main strength members, including the major internal
framing, the hull plating, voids, and ballast tanks, but not including
cargo or fuel oil tanks.
(c) Cargo tank internal examination means an examination of the
vessel while afloat or in drydock and consists of an examination of the
internals of all cargo tanks; except, if the vessel is certificated to
carry cargoes regulated under part 38 or subchapter O of this chapter,
the cargo tank internal examination must be accomplished as specified in
parts 38 and 151 of this chapter respectively.
(d) Underwater survey means the examination, while the vessel is
afloat, of all accessible parts of the vessel's underwater body and all
through-hull fittings.
[CGD 84-024, 52 FR 39653, Oct. 23, 1987, as amended by CGD 84-024, 53 FR
32231, Aug. 24, 1988; CGD 95-028, 62 FR 51206, Sept. 30, 1997]
Sec. 91.40-3 Drydock examination, internal structural examination, cargo tank internal examination, and underwater survey intervals.
(a) Except as provided in paragraphs (b) through (g) of this
section, each vessel must undergo drydock, internal structural, and
cargo tank internal examinations as follows:
(1) Except under paragraph (a)(2) of this section, vessels that
operate in salt water must be examined in accordance with the intervals
set forth in Table 91.40-3(a) of this section. Where Table 91.40-3(a)
indicates a 2.5 year examination interval, it means a vessel must
undergo two examinations within any five year period. No more than three
years may elapse between any two examinations.
[[Page 27]]
Table 91.40-3(a)--Salt Water Service Vessels Examination Intervals in Years
--------------------------------------------------------------------------------------------------------------------------------------------------------
Double hull Double hull Single hull Unmanned
Single hull barge with barge with barge with Wood hull Unmanned double hull
ship and internal external independent ship and deck cargo freight
barge framing \1\ framing \2\ tanks \3\ barge barge \4\ barge \5\
--------------------------------------------------------------------------------------------------------------------------------------------------------
Drydock............................................... 2.5 5.0 5.0 5.0 2.5 5.0 5.0
Internal structural................................... 2.5 2.5 2.5 2.5 2.5 2.5 2.5
Cargo tank internal................................... \6\ 2.5 \6\ 5.0 \6\ 10.0 \6\ 10.0 \6\ 2.5 ............ \6\ 5.0
--------------------------------------------------------------------------------------------------------------------------------------------------------
Note:
\1\ Applicable to double hull tank barges (double sides, ends, and bottoms) when the structural framing is on the internal tank surface.
\2\ Applicable to double hull tank barges (double sides, ends, and bottoms) when the structural framing is on the external tank surface accessible for
examination from voids, double bottoms, and other similar spaces.
\3\ Applicable to single hull tank barges with independent cargo tanks which have a cargo containment envelope that is not a contiguous part of the hull
structure and which has adequate clearance between the tanks and between the tanks and the vessel's hull to provide access for examination of all tank
surfaces and the hull structure.
\4\ Applicable to unmanned/non-permissively manned deck cargo barge which carries cargo only above the weather deck and which provides complete access
for examination of the inside of the hull structure.
\5\ Applicable to unmanned/non-permissively manned double hull freight barges (double sides, ends, and bottoms) the arrangement of which provides access
for a complete internal structural examination as defined in Sec. 91.40-1(b) without the necessity of entering cargo tanks or holds.
\6\ Or as specified in Part 151.
[[Page 28]]
(2) Vessels that operate in fresh water at least six months in every
12 month period since the last drydock examination must be examined in
accordance with the intervals set forth in Table 91.40-3(b) of this
section. Where Table 91.40-3(b) indicates a 2.5 year examination
interval, it means a vessel must undergo two examinations within any
five year period. No more than three years may elapse between any two
examinations.
[[Page 29]]
Table 91.40-3(b)--Fresh Water Service Vessels Examination Intervals in Years
--------------------------------------------------------------------------------------------------------------------------------------------------------
Double hull Double hull Single hull Unmanned
Single hull barge with barge with barge with Wood hull Unmanned double hull
ship and internal external independent ship and deck cargo freight
barge framing \1\ framing \2\ tanks \3\ barge barge \4\ barge \5\
--------------------------------------------------------------------------------------------------------------------------------------------------------
Drydock............................................... 5.0 10.0 10.0 10.0 2.5 10.0 10.0
Internal structural................................... 5.0 5.0 5.0 5.0 2.5 5.0 5.0
Cargo tank internal................................... \6\ 5.0 \6\ 5.0 \6\ 10.0 \6\ 10.0 \6\ 2.5 ............ \6\ 5.0
--------------------------------------------------------------------------------------------------------------------------------------------------------
Note:
\1\ Applicable to double hull tank barges (double sides, ends, and bottoms) when the structural framing is on the internal tank surface.
\2\ Applicable to double hull tank barges (double sides, ends, and bottoms) when the structural framing is on the external tank surface accessible for
examination from voids, double bottoms, and other similar spaces.
\3\ Applicable to single hull tank barges with independent cargo tanks which have a cargo containment envelope that is not a contiguous part of the hull
structure and which has adequate clearance between the tanks and between the tanks and the vessel's hull to provide access for examination of all tank
surfaces and the hull structure.
\4\ Applicable to unmanned/non-permissively manned deck cargo barge which carries cargo only above the weather deck and which provides complete access
for examination of the inside of the hull structure.
\5\ Applicable to unmanned/non-permissively manned double hull freight barges (double sides, ends, and bottoms) the arrangement of which provides access
for a complete internal structural examination as defined in Sec. 91.40-1(b) without the necessity of entering cargo tanks or holds.
\6\ Or as specified in Part 151.
[[Page 30]]
(b) During each inspection or reinspection for certification, all
wing voids, rakes, cofferdams, and other void spaces on barges must be
opened and checked from on-deck for the presence of water or cargo
indicating hull damage or cargo tank leakage. If water or cargo is not
present, these spaces need not be gas freed, ventilated, cleaned, or
otherwise prepared for personnel entry. If water or cargo is present, an
internal structural examination may be required.
(c) If, during an internal structural, cargo tank internal
examination, or underwater survey, damage or deterioration to the hull
plating, structural members, or cargo tanks is discovered, the Officer
in Charge, Marine Inspection, may require the vessel to be drydocked or
otherwise taken out of service to further assess the extent of the
damage and to effect permanent repairs.
(d) Vessels less than 15 years of age (except wooden hull vessels)
that are in salt water service with a 2.5 year drydock interval (as
indicated in Table 91.40-3(a) of this section) or that are in fresh
water service with a five year drydock interval (as indicated in Table
91.40-3(b) of this section) may be considered for an underwater survey
instead of alternate drydock examinations, provided the vessel is fitted
with an effective hull protection system. Vessel owners or operators
must apply to the Officer in Charge, Marine Inspection, for approval of
underwater surveys instead of alternate drydock examinations for each
vessel. The application must include the following information:
(1) The procedure to be followed in carrying out the underwater
survey.
(2) The location where the underwater survey will be accomplished.
(3) The method to be used to accurately determine the diver location
relative to the hull.
(4) The means that will be provided for examining through-hull
fittings.
(5) The means that will be provided for taking shaft bearing
clearances.
(6) The condition of the vessel, including the anticipated draft of
the vessel at the time of the survey.
(7) A description of the hull protection system.
(e) Vessels otherwise qualifying under paragraph (d) of this
section, that are 15 years of age or older, may be considered for
continued participation in or entry into the underwater survey program
on a case-by-case basis if--
(1) Before the vessel's next scheduled drydocking, the owner or
operator submits a request for participation or continued participation
to Commandant (G-MOC);
(2) During the vessel's next drydocking after the request is
submitted, no appreciable hull deterioration is indicated as a result of
a complete set of hull gaugings; and
(3) The results of the hull gauging and the results of the Coast
Guard drydock examination together with the recommendation of the
Officer in Charge, Marine Inspection, are submitted to Commandant (G-
MOC) for final approval.
(f) Each vessel which has not met with the applicable examination
schedules in paragraphs (a) through (e) of this section because it is on
a voyage, must undergo the required examinations upon completion of the
voyage.
(g) The Commandant (G-MOC) may authorize extensions to the
examination intervals specified in paragraph (a) of this section.
[CGD 84-024, 52 FR 39653, Oct. 23, 1987, as amended by CGD 84-024, 53 FR
32231, Aug. 24, 1988; CGD 84-024, 53 FR 34872, Sept. 8, 1988; CGD 95-
072, 60 FR 50464, Sept. 29, 1995; CGD 96-041, 61 FR 50729, Sept. 27,
1996; CGD 95-028, 62 FR 51206, Sept. 30, 1997]
Sec. 91.40-5 Notice and plans required.
(a) The master, owner, operator, or agent of the vessel shall notify
the Officer in Charge, Marine Inspection, whenever the vessel is to be
drydocked regardless of the reason for drydocking.
(b) Each vessel, except barges, that holds a Load Line Certificate
must have on board a plan showing the vessel's scantlings. This plan
must be made available to the Coast Guard marine inspector whenever the
vessel undergoes a drydock examination, internal structural examination,
cargo tank internal examination, or underwater survey or whenever
repairs are made to the vessel's hull.
[[Page 31]]
(c) Each barge that holds a Load Line Certificate must have a plan
showing the barge's scantlings. The plan need not be maintained on board
the barge but must be made available to the Coast Guard marine inspector
whenever the barge undergoes a drydock examination, internal structural
examination, or cargo tank internal examination, or underwater survey or
whenever repairs are made to the barge's hull.
[CGD 84-024, 52 FR 39654, Oct. 23, 1987]
Subpart 91.43--Integral Fuel Oil Tank Examinations
Sec. 91.43-1 When required.
(a) Each fuel oil tank with at least one side integral to the
vessel's hull and located within the hull (``integral fuel oil tank'')
is subject to inspection as provided in this section. The owner or
operator of the vessel shall have the tanks cleaned out and gas freed as
necessary to permit internal examination of the tank or tanks designated
by the marine inspector. The owner or operator shall arrange for an
examination of the fuel tanks of each vessel during an internal
structural examination at intervals not to exceed five years.
(b) Integral non-double-bottom fuel oil tanks need not be cleaned
out and internally examined if the marine inspector is able to determine
by external examination that the general condition of the tanks is
satisfactory.
(c) Double-bottom fuel oil tanks on vessels less than 10 years of
age need not be cleaned out and internally examined if the marine
inspector is able to determine by external examination that the general
condition of the tanks is satisfactory.
(d) All double-bottom fuel oil tanks on vessels 10 years of age or
older but less than 15 years of age need not be cleaned out and
internally examined if the marine inspector is able to determine by
internal examination of at least one forward double-bottom fuel oil
tank, and by external examination of all other double-bottom fuel oil
tanks on the vessel, that the general condition of the tanks is
satisfactory.
(e) All double-bottom fuel oil tanks on vessels 15 years of age or
older but less than 25 years of age need not be cleaned out and
internally examined if the marine inspector is able to determine by
internal examination of at least one forward, one amidships, and one aft
double-bottom fuel oil tank, and by external examination of all other
double-bottom fuel oil tanks on the vessel, that the general condition
of the tanks is satisfactory.
(f) All double-bottom fuel oil tanks on vessels 25 years of age or
older need not be cleaned out and internally examined if the marine
inspector is able to determine by internal examination of at least one
double-bottom fuel oil tank in way of each cargo hold/tank, and by
external examination of all other double-bottom fuel oil tanks, that the
general condition of the tanks is satisfactory.
[CGD 84-024, 52 FR 39654, Oct. 23, 1987, as amended by CGD 84-024, 53 FR
32232, Aug. 24, 1988]
Subpart 91.45--Repairs and Alterations
Sec. 91.45-1 Notice required.
(a) No repairs or alterations affecting the safety of the vessel
with regard to the hull, machinery, or equipment, shall be made without
the knowledge of the Officer in Charge, Marine Inspection.
(b) Drawings of alterations shall be approved before work is started
unless deemed unnecessary by the Officer in Charge, Marine Inspection.
(c) Drawings will not be required for repairs in kind.
Sec. 91.45-5 Inspection required.
(a) An inspection either general or partial depending upon the
circumstances shall be made whenever any important repairs or
alterations are undertaken.
[[Page 32]]
Subpart 91.50--Special Operating Requirements
Sec. 91.50-1 Inspection and testing required when making alterations, repairs, or other such operations involving riveting, welding, burning or like fire-
producing actions.
(a) The provisions of ``Standard for The Control of Gas Hazards on
Vessels to be Repaired,'' NFPA No. 306, published by National Fire
Protection Association, 1 Batterymarch Park, Quincy, MA 02669, shall be
used as a guide in conducting the inspections and issuance of
certificates required by this section.
(b) Until an inspection has been made to determine that such
operation can be undertaken with safety, no alterations, repairs, or
other such operations involving riveting, welding, burning, or like
fire-producing actions shall be made:
(1) Within or on the boundaries of cargo tanks which have been used
to carry combustible liquids or chemicals in bulk; or,
(2) Within spaces adjacent to cargo tanks which have been used to
carry Grade D combustible liquid cargo, except where the distance
between such cargo tanks and the work to be performed is not less than
twenty-five (25) feet; or,
(3) Within or on the boundaries of fuel tanks; or,
(4) To pipelines, heating coils, pumps, fittings, or other
appurtenances connected to such cargo or fuel tanks; or,
(5) On miscellaneous vessels such as cable, salvage, pile driving,
and oil drilling rig vessels that have been specially authorized to
carry Grade B or Grade C flammable liquid cargo in bulk by the
Commandant, within or on the boundaries of such cargo tanks or within
spaces adjacent to such cargo tanks.
(c) Such inspections shall be made and evidenced as follows:
(1) In ports or places in the United States or its territories and
possessions the inspection shall be made by a marine chemist
certificated by the National Fire Protection Association; however, if
the services of such certified marine chemist are not reasonably
available, the Officer in Charge, Marine Inspection, upon the
recommendation of the vessel owner and his contractor or their
representative, shall select a person who, in the case of an individual
vessel, shall be authorized to make such inspection. If the inspection
indicates that such operations can be undertaken with safety, a
certificate setting forth the fact in writing and qualified as may be
required, shall be issued by the certified marine chemist or the
authorized person before the work is started. Such qualifications shall
include any requirements as may be deemed necessary to maintain, insofar
as can reasonably be done, the safe conditions in the spaces certified
throughout the operation and shall include such additional tests and
certifications as considered required. Such qualifications and
requirements shall include precautions necessary to eliminate or
minimize hazards that may be present from protective coatings or
residues from cargoes.
(2) When not in such a port or place, and a marine chemist or such
person authorized by the Officer in Charge, Marine Inspection, is not
reasonably available, the inspection shall be made by the senior officer
present and a proper entry shall be made in the vessel's logbook.
(d) It shall be the responsibility of the senior officer present to
secure copies of certificates issued by the certified marine chemist or
such person authorized by the Officer in Charge, Marine Inspection. It
shall be the responsibility of the senior officer present, insofar as
the persons under his control are concerned, to maintain a safe
condition on the vessel by full observance of all qualifications and
requirements listed by the marine chemist in the certificate.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 95-072, 60 FR
50464, Sept. 29, 1995]
Subpart 91.55--Plan Approval
Sec. 91.55-1 General.
(a) The following list of required plans is general in character,
but includes all plans which normally show construction and safety
features coming under the cognizance of the Coast Guard. In the case of
a particular vessel, all of the plans enumerated may
[[Page 33]]
not be applicable, and it is intended that only those plans and
specifications be submitted as will clearly show the vessel's
arrangement, construction and required equipment.
(b) In the following list of required plans, the items which must be
approved by the American Bureau of Shipping for vessels classed by that
organization are indicated by an asterisk. When prints bearing record of
such approval by the American Bureau of Shipping are forwarded to the
Coast Guard they will in general be accepted as satisfactory except
insofar as the law or the Coast Guard regulations contain requirements
which are not covered by the American Bureau of Shipping.
(c) Plans and specifications for cargo gear shall be approved by
either a recognized classification society or a recognized cargo gear
organization, as specified in Sec. 91.25-25.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 95-028, 62 FR
51206, Sept. 30, 1997]
Sec. 91.55-5 Plans and specifications required for new construction.
(a) General. (1) Specifications.
(2) General Arrangement Plan of decks, holds, inner bottoms, etc.,
and including inboard and outboard profile.
(b) Hull structure. 1 (1) *Inner Bottom Plating and
Framing.
---------------------------------------------------------------------------
1 The asterisk (*) indicates items which may require
approval by the American Bureau of Shipping for vessels classed by that
society.
---------------------------------------------------------------------------
(2) *Midship Section.
(3) *Shell Plating and Framing.
(4) *Stem, Stern Frame, and Rudder.
(5) *Structural Deck Plans for Strength Decks.
(6) *Pillars and Girders.
(7) *Watertight and Oiltight Bulkheads.
(8) *Foundations for Main Machinery and Boilers.
(9) *Arrangement of Ports, Doors, and Airports in Shell Plating.
(10) *Hatch Coamings and Covers in Weather and Watertight Decks.
(11) *Details of Hinged Subdivision Watertight Doors and Operating
Gear.
(12) *Scuppers and Drains Penetrating Shell Plating.
(13) *Arrangement of the cargo gear including a stress diagram. The
principal details of the gear and the safe working load for each
component part shall be shown.
(c) Subdivision and stability. Plans and calculations as required by
Subchapter S of this chapter.
(d) Fire control. (1) General arrangement plans showing for each
deck the control stations, the various fire sections enclosed by fire
resisting bulkheads, the arrangement of the alarm and extinguishing
systems, the fire extinguishers, means of access to different
compartments and decks and the ventilation system including location of
ventilation shutdowns, positions of dampers and the numbers identifying
each system.
(2) Ventilation diagram including dampers and other fire control
features.
(3) Details of alarm systems.
(4) Details of extinguishing systems, including fire mains, carbon
dioxide, foam and sprinkling systems.
(e) Marine engineering. For plans required for marine engineering
equipment and systems, see subchapter F (Marine Engineering) of this
chapter.
(f) Electrical engineering. For plans required for electrical
engineering, equipment and systems, see subchapter J (Electrical
Engineering) of this chapter.
(g) Lifesaving equipment. (1) These plans are to show the location
and arrangement of embarkation decks, all overboard discharges and
projections in way of launching lifeboats, weights of lifeboats fully
equipped and loaded, working loads of davits and winches, types and
sizes of falls, the manufacturer's name and identification for all
equipment, and all other relevant and necessary information.
(i) Arrangement of lifeboats.
(ii) Arrangement of davits.
(iii) Location and stowage of liferafts and buoyant apparatus.
(h) Crew's accommodations. (1) Arrangement plans showing
accommodations, ventilation, escapes, hospital, and sanitary facilities
for all crewmembers.
(i) Navigation bridge visibility. For vessels of 100 meters (328
feet) or more in
[[Page 34]]
length contracted for on or after September 7, 1990, a plan must be
included which shows how visibility from the navigation bridge will meet
the standards contained in Sec. 92.03-1 of this subchapter.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 79-023, 48 FR
51008, Nov. 4, 1983; CGD 85-099, 55 FR 32248, Aug. 8, 1990; CGD 85-099,
55 FR 40260, Oct. 2, 1990; CGD 88-032, 56 FR 35825, July 29, 1991; 56 FR
46354, Sept. 11, 1991]
Sec. 91.55-10 Plans required for alterations of existing vessels.
(a) In the event of alterations involving the safety of the vessel,
the applicable plans shall be submitted for approval covering the
proposed work except as modified by Sec. 91.45-1. The general scope of
the plans shall be as noted in Sec. 91.55-5.
Sec. 91.55-15 Procedure for submittal of plans.
(a) As the relative location of shipyards, design offices, and Coast
Guard offices vary throughout the country, no specific routing will be
required in the submittal of plans. In general, one of the following
procedures would apply, but in a particular case, if a more expeditious
procedure can be used, there will be no objection to its adoption.
(1) The plans may be submitted to the Officer in Charge, Marine
Inspection, in the district in which the vessel is to be built. This
procedure will be most expeditious in the case of those offices where
personnel and facilities are available for examination and approval of
the plans locally.
(2) The plans may be submitted directly to the Commandant (G-MSE),
U.S. Coast Guard, Washington, DC 20593-0001. In this case, the plans
will be returned directly to the submitter, with a copy of the action
being forwarded to the interested Officer in Charge, Marine Inspection.
(3) The plans may be submitted directly to Commanding Officer, U.S.
Coast Guard Marine Safety Center, 400 Seventh St., SW., Washington, DC
20590-0001.
(4) In the case of classed vessels, upon specific request by the
submitter, the American Bureau of Shipping will arrange to forward the
necessary plans to the Coast Guard indicating its action thereon. In
this case, the plans will be returned as noted in paragraph (a)(2) of
this section.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 78-128, 47 FR
21204, May 17, 1982; CGD 82-063b, 48 FR 4781, Feb. 3, 1983; CGD 88-070,
53 FR 34534, Sept. 7, 1988; CGD 89-025, 54 FR 19571, May 8, 1989; CGD
96-041, 61 FR 50729, Sept. 27, 1996]
Sec. 91.55-20 Number of plans required.
(a) Three copies of each plan are normally required so that one can
be returned to the submitter. If the submitter desires additional
approved plans, a suitable number should be submitted to permit the
required distribution.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGFR 69-116, 35
FR 6861, Apr. 30, 1970]
Subpart 91.60--Certificates Under International Convention for Safety of
Life at Sea, 1974
Sec. 91.60-1 Application.
The provisions of this subpart shall apply to all cargo vessels on
an international voyage. (See Sec. 91.05-10 of this chapter.)
[CGD 95-012, 60 FR 48051, Sept. 18, 1995, as amended by USCG 1999-4976,
65 FR 6503, Feb. 9, 2000]
Sec. 91.60-5 Cargo Ship Safety Construction Certificate.
(a) All vessels on an international voyage are required to have a
Cargo Ship Safety Construction Certificate. This certificate shall be
issued by the U.S. Coast Guard or the American Bureau of Shipping to
certain vessels on behalf of the United States of America as provided in
Regulation 12, chapter I, of the International Convention for Safety of
Life at Sea, 1974.
(b) All such vessels shall meet the applicable requirements of this
chapter for vessels on an international voyage.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 90-008, 55 FR
30661, July 26, 1990]
[[Page 35]]
Sec. 91.60-10 Cargo Ship Safety Equipment Certificate.
(a) All vessels on an international voyage are required to have a
Cargo Ship Safety Equipment Certificate.
(b) All such vessels shall meet the applicable requirements of this
chapter for vessels on an international voyage.
Sec. 91.60-15 Cargo Ship Safety Radio Certificate.
Every vessel equipped with a radio installation on an international
voyage must have a Cargo Ship Safety Radio Certificate. Each radio
installation must meet the requirements of the Federal Communication
Commission and the International Convention for Safety of Life at Sea.
[USCG 1999-4976, 65 FR 6503, Feb. 9, 2000]
Sec. 91.60-25 Exemption Certificate.
(a) A vessel may be exempted by the Commandant from complying with
certain requirements of the Convention under his administration upon
request made in writing to him and transmitted via the Officer in
Charge, Marine Inspection.
(b) When an exemption is granted to a vessel by the Commandant under
and in accordance with the Convention, an Exemption Certificate
describing such exemption shall be issued through the appropriate
Officer in Charge, Marine Inspection, in addition to other required
certificates.
Sec. 91.60-30 Safety Management Certificate.
All vessels to which 33 CFR part 96 applies on an international
voyage must have a valid Safety Management Certificate and a copy of
their company's valid Document of Compliance certificate on board.
[CGD 95-073, 62 FR 67514, Dec. 24, 1997]
Sec. 91.60-35 Availability of Certificates.
The Convention certificates must be on board the vessel and readily
available for examination at all times.
[USCG 1999-4976, 65 FR 6503, Feb. 9, 2000]
Sec. 91.60-40 Duration of Convention certificates.
(a) The following certificates are valid for a period of not more
than 60 months.
(1) A Cargo Ship Safety Construction Certificate.
(2) A Cargo Ship Safety Equipment Certificate.
(3) A Safety Management Certificate.
(4) A Cargo Ship Safety Radio Certificate.
(b) An Exemption certificate must not be valid for longer than the
period of the certificate to which it refers.
(c) A Convention certificate may be withdrawn, revoked, or suspended
at any time when it is determined that the vessel is no longer in
compliance with applicable requirements. (See Sec. 2.01-70 of this
chapter for procedures governing appeals.)
[USCG 1999-4976, 65 FR 6503, Feb. 9, 2000]
Sec. 91.60-45 American Bureau of Shipping.
(a) The American Bureau of Shipping, with its home office at ABS
Plaza, 16855 Northchase Drive, Houston, TX 77060, is hereby designated
as an organization duly authorized to issue the ``Cargo Ship Safety
Construction Certificate'' to certain cargo ships on behalf of the
United States of America as provided in Regulation 12, chapter I, of the
International Convention for Safety of Life at Sea, 1974, and Executive
Order 12234 and the certificate shall be subject to the requirements in
this subpart. The American Bureau of Shipping is authorized to place the
official seal of the United States of America on the certificate. This
designation and delegation to the American Bureau of Shipping shall be
in effect until terminated by proper authority and notice of
cancellation is published in the Federal Register.
(b) At the option of the owner or agent of a vessel on an
international voyage and on direct application to the American Bureau of
Shipping, the Bureau may issue to such vessel a Cargo Ship Safety
Construction Certificate, having a period of validity of not more than
60 months after ascertaining that the vessel:
[[Page 36]]
(1) Has met the applicable requirements of the Convention; and,
(2) Is currently classed by the Bureau and classification
requirements have been dealt with to the satisfaction of the Bureau.
(c) When the Bureau determines that a vessel to which it has issued
a Cargo Ship Safety Construction Certificate no longer complies with the
Bureau's applicable requirements for classification, the Bureau shall
immediately furnish to the Coast Guard all relevant information, which
will be used by the Coast Guard to determine whether or not to withdraw,
revoke or suspend the Cargo Ship Safety Construction Certificate.
[CGFR 65-50, 30 FR 16974, Dec. 30, 1965, as amended by CGD 90-008, 55 FR
30661, July 26, 1990; CGD 96-041, 61 FR 50729, Sept. 27, 1996; USCG-
2000-7790, 65 FR 58461, Sept. 29, 2000]
PART 92--CONSTRUCTION AND ARRANGEMENT--Table of Contents
Subpart 92.01--Hull Structure
Sec.
92.01-1 Application.
92.01-5 Vessels subject to load line.
92.01-10 Structural standards.
92.01-15 Special consideration.
92.01-90 Vessels contracted for prior to November 19, 1952.
Subpart 92.03--Navigation Bridge Visibility
92.03-1 Navigation bridge visibility.
Subpart 92.05--General Fire Protection
92.05-1 Fire hazards to be minimized.
92.05-5 Woodwork insulated from heated surfaces.
92.05-10 Lamp room construction.
92.05-15 Segregation of spaces containing the emergency source of
electric power.
Subpart 92.07--Structural Fire Protection
92.07-1 Application.
92.07-5 Definitions.
92.07-10 Construction.
92.07-90 Vessels contracted for prior to July 1, 1968.
Subpart 92.10--Means of Escape
92.10-1 Application.
92.10-5 Two means required.
92.10-10 Location.
92.10-15 Vertical ladders not accepted.
92.10-20 No means for locking doors.
92.10-25 Stairway size.
92.10-30 Dead end corridors.
92.10-35 Public spaces.
92.10-40 Access to lifeboats.
92.10-45 Weather deck communications.
92.10-90 Vessels contracted for prior to November 19, 1952.
Subpart 92.15--Ventilation
92.15-1 Application.
92.15-5 Vessels using fuel having a flashpoint of 110 degrees or lower.
92.15-10 Ventilation for closed spaces.
92.15-15 Ventilation for crew quarters and, where provided, passenger
spaces.
92.15-90 Vessels contracted for prior to November 19, 1952.
Subpart 92.20--Accommodations for Officers and Crew
92.20-1 Application.
92.20-5 Intent.
92.20-10 Location of crew spaces.
92.20-15 Construction.
92.20-20 Sleeping accommodations.
92.20-25 Washrooms and toilet rooms.
92.20-30 Messrooms.
92.20-35 Hospital space.
92.20-40 Other spaces.
92.20-45 Lighting.
92.20-50 Heating and cooling.
92.20-55 Insect screens.
92.20-90 Vessels contracted for prior to November 19, 1952.
Subpart 92.25--Rails and Guards
92.25-1 Application.
92.25-5 Where rails required.
92.25-10 Storm rails.
92.25-15 Guards in dangerous places.
92.25-90 Vessels contracted for prior to July 1, 1969.
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
Source: CGFR 65-50, 30 FR 16983, Dec. 30, 1965, unless otherwise
noted.
Subpart 92.01--Hull Structure
Sec. 92.01-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 92.01-90, shall apply to all vessels contracted for on or after
November 19, 1952. Vessels contracted for prior to November 19, 1952,
shall meet the requirements of Sec. 92.01-90.
Sec. 92.01-5 Vessels subject to load line.
(a) For vessels assigned a load line, see subchapter E (Load Lines)
of this
[[Page 37]]
chapter, for special requirements as to strength, closure of openings,
etc.
Sec. 92.01-10 Structural standards.
(a) In general, compliance with the standards established by the
American Bureau of Shipping, see subpart 90.35 of this subchapter, will
be considered as satisfactory evidence of the structural efficiency of
the vessel. However, in special cases, a detailed analysis of the entire
structure or some integral part may be made by the Coast Guard to
determine the structural requirements.
Sec. 92.01-15 Special consideration.
(a) Special consideration will be given to the structural
requirements for small vessels or vessels of an unusual design not
contemplated by the rules of the American Bureau of Shipping.
Sec. 92.01-90 Vessels contracted for prior to November 19, 1952.
(a) Existing structure previously approved will be considered
satisfactory so long as it is maintained in good condition to the
satisfaction of the Officer in Charge, Marine Inspection. Minor repairs
and alterations may be made to the same standard as the original
construction.
Subpart 92.03--Navigation Bridge Visibility
Sec. 92.03-1 Navigation bridge visibility.
Each cargo and miscellaneous vessel which is 100 meters (328 feet)
or more in length and contracted for on or after September 7, 1990, must
meet the following requirements:
(a) The field of vision from the navigation bridge, whether the
vessel is in a laden or unladen condition, must be such that:
(1) From the conning position, the view of the sea surface is not
obscured forward of the bow by more than the lesser of two ship lengths
or 500 meters (1,640 feet) from dead ahead to 10 degrees on either side
of the vessel. Within this arc of visibility any blind sector caused by
cargo, cargo gear, or other permanent obstruction must not exceed 5
degrees.
(2) From the conning position, the horizontal field of vision
extends over an arc from at least 22.5 degrees abaft the beam on one
side of the vessel, through dead ahead, to at least 22.5 degrees abaft
the beam on the other side of the vessel. Blind sectors forward of the
beam caused by cargo, cargo gear, or other permanent obstruction must
not exceed 10 degrees each, nor total more than 20 degrees, including
any blind sector within the arc of visibility described in paragraph
(a)(1) of this section.
(3) From each bridge wing, the field of vision extends over an arc
from at least 45 degrees on the opposite bow, through dead ahead, to at
least dead astern.
(4) From the main steering position, the field of vision extends
over and arc from dead ahead to at least 60 degrees on either side of
the vessel.
(5) From each bridge wing, the respective side of the vessel is
visible forward and aft.
(b) Windows fitted on the navigation bridge must be arranged so
that:
(1) Framing between windows is kept to a minimum and is not
installed immediately in front of any work station.
(2) Front windows are inclined from the vertical plane, top out, at
an angle of not less than 10 degrees and not more than 25 degrees.
(3) The height of the lower edge of the front windows is limited to
prevent any obstruction of the foward view previously described in this
section.
(4) The height of the upper edge of the front windows allows a
foward view of the horizon at the conning position, for a person with a
height of eye of 1.8 meters (71 inches), when the vessel is at a forward
pitch angle of 20 degrees.
(c) Polarized or tinted windows must not be fitted.
[CGD 85-099, 55 FR 32248, Aug. 8, 1990]
Subpart 92.05--General Fire Protection
Sec. 92.05-1 Fire hazards to be minimized.
(a) The general construction of the vessel shall be such as to
minimize fire hazards insofar as is reasonable and practicable.
[[Page 38]]
Sec. 92.05-5 Woodwork insulated from heated surfaces.
(a) Internal combustion engine exhausts, boiler and galley uptakes,
and similar sources of ignition shall be kept clear of and suitably
insulated from any woodwork or other combustible matter.
Sec. 92.05-10 Lamp room construction.
(a) Lamp, paint, and oil lockers and similar compartments shall be
constructed of steel or shall be wholly lined with metal.
Sec. 92.05-15 Segregation of spaces containing the emergency source of electric power.
(a) The provisions of this section shall apply to all vessels
contracted for on or after October 1, 1958.
(b) When a compartment containing the emergency source of electric
power, or vital components thereof, adjoins a space containing either
the ship's service generators or machinery necessary for the operation
of the ship's service generators, all common bulkheads and/or decks
shall be protected by approved ``structural insulation'' or other
approved material. This protection shall be such as to be capable of
preventing an excessive temperature rise in the space containing the
emergency source of electric power, or vital components thereof, for a
period of at least one hour in the event of fire in the adjoining space.
Bulkheads or decks meeting Class A-60 requirements, as defined by
Sec. 72.05-10 of Subchapter H (Passenger Vessels) of this chapter, will
be considered as meeting the requirements of this paragraph.
Subpart 92.07--Structural Fire Protection
Sec. 92.07-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 92.07-90, shall apply to all vessels of 4,000 gross tons and over
contracted for on or after January 1, 1962. Such vessels contracted for
prior to January 1, 1962, shall meet the requirements of Sec. 92.07-
90(a).
(b) The provisions of this subpart, with the exception of
Sec. 92.07-90, shall apply to all industrial vessels of 300 gross tons
and over but less than 4,000 gross tons, contracted for on or after July
1, 1968, which carry in excess of 12 industrial personnel. Such vessels
contracted for prior to July 1, 1968, shall meet the requirements of
Sec. 92.07-90(b).
(c) SOLAS-certificated vessels complying with method IC, as
described in SOLAS 74, regulation II-2/42, may be considered equivalent
to the provisions of this subpart.
[CGFR 67-90, 33 FR 1015, Jan. 26, 1968, as amended by CGD 95-028, 62 FR
51206, Sept. 30, 1997]
Sec. 92.07-5 Definitions.
(a) Standard fire test. A ``standard fire test'' is one which
develops in the test furnace a series of time temperature relationships
as follows:
5 minutes--1,000 deg.F.
10 minutes--1,300 deg.F.
30 minutes--1,550 deg.F.
60 minutes--1,700 deg.F.
(b) ``A'' Class divisions. Bulkheads or decks of the ``A'' Class
shall be composed of steel or equivalent metal construction, suitably
stiffened and made intact with the main structure of the vessel; such as
shell, structural bulkheads, and decks. They shall be so constructed,
that if subjected to the standard fire test, they would be capable of
preventing the passage of flame and smoke for one hour.
(c) ``B'' Class bulkheads. Bulkheads of the ``B'' Class shall be
constructed with approved incombustible materials and made intact from
deck to deck and to shell or other boundaries. They shall be so
constructed that, if subjected to the standard fire test, they would be
capable of preventing the passage of flame for one half hour.
(d) ``C'' Class divisions. Bulkheads or decks of the ``C'' Class
shall be constructed of approved incombustible materials, but need meet
no requirements relative to the passage of flame.
(e) Steel or other equivalent metal. Where the term ``steel or other
equivalent metal'' is used in this subpart, it is intended to require a
material which, by itself or due to insulation provided, has structural
and integrity qualities equivalent to steel at the end of the applicable
fire exposure.
[[Page 39]]
(f) Approved material. Where in this subpart approved materials are
required, they refer to materials approved under the applicable subparts
of Subchapter Q (Specifications) of this chapter, as follows:
Deck Coverings................................................ 164.006
Structural Insulations........................................ 164.007
Bulkhead Panels............................................... 164.008
Incombustible Materials....................................... 164.009
Interior Finishes............................................. 164.012
(g) Stairtower. A stairtower is a stairway which penetrates more
than a single deck within the same enclosure.
[CGFR 65-50, 30 FR 16983, Dec. 30, 1965, as amended by CGFR 67-90, 33 FR
1015, Jan. 26, 1968; CGD 75-032, 41 FR 17910, Apr. 29, 1976]
Sec. 92.07-10 Construction.
(a) The hull, superstructure, structural bulkheads, decks, and
deckhouses shall be constructed of steel. Alternately, the Commandant
may permit the use of other suitable material in special cases, having
in mind the risk of fire.
(b) Bulkheads of galleys, paint and lamp lockers, and emergency
generator rooms shall be of ``A'' Class construction.
(c) The boundary bulkheads and decks separating the accommodations
and control stations from cargo and machinery spaces, galleys, main
pantries and storerooms, other than small service lockers, shall be of
``A'' Class construction.
(d) Within the accommodation and service areas the following
conditions shall apply:
(1) Corridor bulkheads in accommodation spaces shall be of the ``A''
or ``B'' Class intact from deck to deck. Stateroom doors in such
bulkheads may have a louver in the lower half.
(2) Stairtowers, elevator, dumbwaiter, and other trunks shall be of
``A'' Class construction.
(3) Bulkheads not already specified to be of ``A'' or ``B'' Class
construction may be of ``A'', ``B'', or ``C'' Class construction.
(4) The integrity of any deck in way of a stairway opening, other
than a stairtower, shall be maintained by means of ``A'' or ``B'' class
bulkheads and doors at one level. The integrity of a stairtower shall be
maintained by ``A'' Class doors at every level. The doors shall be of
self-closing type. Holdback hooks, or other means of permanently holding
the door open will not be permitted. However, magnetic holdbacks
operated from the bridge or from other suitable remote control positions
are acceptable.
(5) Interior stairs, including stringers and treads, shall be of
steel.
(6) Except for washrooms and toilet spaces, deck coverings within
accommodation spaces shall be of an approved type. However, overlays for
leveling or finishing purposes which do not meet the requirements for an
approved deck covering may be used in thicknesses not exceeding \3/8\ of
an inch.
(7) Ceilings, linings, and insulation, including pipe and duct
laggings, shall be of approved incombustible materials.
(8) Any sheathing, furring or holding pieces incidental to the
securing of any bulkhead, ceiling, lining, or insulation shall be of
approved incombustible materials.
(9) Bulkheads, linings, and ceilings may have a combustible veneer
within a room not to exceed \2/28\ of an inch in thickness. However,
combustible veneers, trim, decorations, etc., shall not be used in
corridors or hidden spaces. This is not intended to preclude the use of
an approved interior finish or a reasonable number of coat of paint.
(e) Wood hatch covers may be used between cargo spaces or between
stores spaces. Hatch covers in other locations shall be of steel or
equivalent metal construction. Tonnage openings shall be closed by means
of steel plates.
(f) Nitrocellulose or other highly flammable or noxious fume-
producing paints or lacquers shall not be used.
(g) The provisions of paragraph (d) (1) through (9) of this section
apply to control spaces on vessels whose initial Application for
Inspection is submitted to an Officer in Charge, Marine Inspection on or
after June 15, 1987.
[CGFR 65-50, 30 FR 16983, Dec. 30, 1965, as amended by CGFR 67-90, 33 FR
1015, Jan. 26, 1968; CGD 84-073, 52 FR 18364, May 15, 1987; 52 FR 22751,
June 15, 1987]
[[Page 40]]
Sec. 92.07-90 Vessels contracted for prior to July 1, 1968.
(a) For all vessels of 4,000 gross tons and over contracted for
prior to January 1, 1962, existing structure arrangements and materials
previously approved will be considered satisfactory so long as they are
maintained in good condition to the satisfaction of the Officer in
Charge, Marine Inspection. Minor repairs and alterations may be made to
the same standard as the original construction. Major alterations and
conversions shall be in compliance with the provisions of this subpart
to the satisfaction of the Officer in Charge, Marine Inspection.
(b) For industrial vessels of 300 gross tons and over but less than
4,000 gross tons, contracted for prior to July 1, 1968, which carry in
excess of 12 industrial personnel, existing structure arrangements and
materials previously approved will be considered satisfactory so long as
they are maintained in good condition to the satisfaction of the Officer
in Charge, Marine Inspection. Minor repairs and alterations may be made
to the same standard as the original construction. Major alterations and
conversions shall be in compliance with this subpart to the satisfaction
of the Officer in Charge, Marine Inspection.
[CGFR 67-90, 33 FR 1016, Jan. 26, 1968]
Subpart 92.10--Means of Escape
Sec. 92.10-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 92.10-90, shall apply to all vessels contracted for on or after
November 19, 1952. Vessels contracted for prior to November 19, 1952,
shall meet the requirements of Sec. 92.10-90.
Sec. 92.10-5 Two means required.
(a) There shall be at least two means of escape from all general
areas accessible to the passengers, if carried, or where the crew may be
quartered or normally employed. At least one of these two means of
escape shall be independent of watertight doors.
Sec. 92.10-10 Location.
(a) The two means of escape shall be as remote as practicable so as
to minimize the possibility of one incident blocking both escapes.
Sec. 92.10-15 Vertical ladders not accepted.
(a) Vertical ladders and deck scuttles shall not in general be
considered satisfactory as one of the required means of escape. However,
where it is demonstrated that the installation of a stairway would be
impracticable, a vertical ladder may be used as the second means of
escape.
Sec. 92.10-20 No means for locking doors.
(a) No means shall be provided for locking doors giving access to
either of the two required means of escape, except that crash doors or
locking devices, capable of being easily forced in an emergency, may be
employed provided a permanent and conspicuous notice to this effect is
attached to both sides of the door. This paragraph shall not apply to
outside doors to deckhouses where such doors are locked by key only and
such key is under the control of one of the vessel's officers.
Sec. 92.10-25 Stairway size.
(a) Stairways shall be of sufficient width having in mind the number
of persons having access to such stairs for escape purposes.
(b) Vessels contracted for on or after January 1, 1959, shall meet
the requirements of this paragraph. Special consideration for relief may
be given in the case of small vessels if it is shown to be unreasonable
or impracticable to meet the requirements.
(1) All interior stairways, other than those within the machinery
spaces or cargo holds, shall have a minimum width of 28 inches. The
angle of inclination with the horizontal of such stairways shall not
exceed 50 degrees.
Sec. 92.10-30 Dead end corridors.
(a) Dead end corridors, or the equivalent, more than 40 feet in
length shall not be permitted.
[[Page 41]]
Sec. 92.10-35 Public spaces.
(a) In all cases, public spaces having a deck area of over 300
square feet shall have at least two exits. Where practicable, these
exits shall give egress to different corridors, rooms, or spaces to
minimize the possibility of one incident blocking both exits.
Sec. 92.10-40 Access to lifeboats.
(a) The stairways, corridors, and doors shall be so arranged as to
permit a ready and direct access to the various lifeboat embarkation
areas.
Sec. 92.10-45 Weather deck communications.
(a) Vertical communication shall be provided between the various
weather decks by means of permanent inclined ladders.
Sec. 92.10-90 Vessels contracted for prior to November 19, 1952.
(a) Existing arrangements previously approved will be considered
satisfactory so long as they are maintained in good condition to the
satisfaction of the Officer in Charge, Marine Inspection. Minor repairs
and alterations may be made to the same standards as the original
design: Provided, That in no case will a greater departure from the
standards of Secs. 92.10-5 through 92.10-45 be permitted than presently
exists. Nothing in this paragraph shall be construed as exempting any
vessel from having 2 means of escape from all main compartments which
are accessible to the passengers, if carried, or where the crew are
normally quartered or employed.
Subpart 92.15--Ventilation
Sec. 92.15-1 Application.
The provisions of this subpart, with the exception of Sec. 92.15-90,
shall apply to all vessels contracted for on or after November 19, 1952.
Vessels contracted for prior to November 19, 1952, shall meet the
requirements of Sec. 92.15-90.
Sec. 92.15-5 Vessels using fuel having a flashpoint of 110 degrees or lower.
(a) Where liquid fuel having a flashpoint of 110 degrees F. or lower
is used for main or auxiliary machinery or for starting purposes, the
spaces containing such machinery or fuel tanks shall have ventilation as
required by this section.
(1) At least 2 ventilators fitted with cowls or their equivalent for
the purpose of properly and effectively ventilating the bilges of every
engine and fuel-tank compartment in order to remove any flammable or
explosive gases.
(2) Vessels constructed so that the greater portions of the bilges
under the engine and fuel tanks are open or exposed to the natural
atmosphere at all times are not required to be fitted with ventilators.
Sec. 92.15-10 Ventilation for closed spaces.
(a) Except as noted in paragraph (c) of this section, all enclosed
spaces within the vessel shall be properly vented or ventilated. Means
shall be provided to close off all vents and ventilators.
(b) Means shall be provided for stopping all fans in ventilation
systems serving machinery and cargo spaces and for closing all doorways,
ventilators and annular spaces around funnels and other openings to such
spaces, from outside these spaces, in case of fire.
(c) On unmanned cargo barges not fitted with a fixed bilge system,
vents and ventilators may be omitted from void spaces.
(d) The ventilation of spaces which are ``specially suitable for
vehicles'' shall be in accordance with the provisions of this paragraph.
In addition, if vehicles are operated inside of enclosed spaces, the
ventilation shall be in accordance with subpart 97.80 of this
subchapter.
(1) Areas below the weather deck shall be provided with continuous
pressure-positive ventilation at each level on which vehicles are
transported.
(2) The quantity of ventilating air shall be not less than 1 cubic
foot per minute per square foot of deck area.
(3) The ventilation system shall be such as to prevent air
stratification as well as to prevent the accumulation of air pockets.
(4) An alarm system shall be provided which will indicate the loss
of required
[[Page 42]]
ventilation. The alarm location shall be in a normally manned space
acceptable to the Commandant.
(e) For requirements regarding controls of electrically powered
ventilation systems, see subchapter J (Electrical Engineering) of this
chapter.
[CGFR 65-50, 30 FR 16983, Dec. 30, 1965, as amended by CGFR 66-33, 31 FR
15284, Dec. 5, 1966]
Sec. 92.15-15 Ventilation for crew quarters and, where provided, passenger spaces.
(a) All living spaces shall be adequately ventilated in a manner
suitable to the purpose of the space.
(b) On vessels of 100 gross tons and over, except for such spaces as
are so located that under all ordinary conditions of weather, windows,
ports, skylights, etc., and doors to passageways can be kept open, all
crew spaces shall be ventilated by a mechanical system, unless it can be
shown that a natural system will provide adequate ventilation. However,
vessels which trade regularly in the tropics shall, in general, be
fitted with a mechanical ventilation system.
Sec. 92.15-90 Vessels contracted for prior to November 19, 1952.
(a) Existing arrangements previously approved will be considered
satisfactory so long as they are maintained in good condition to the
satisfaction of the Officer in Charge, Marine Inspection. Minor repairs
and alterations may be made to the same standards as the original design
provided that in no case will a greater departure from the standards of
Secs. 92.15-5 through 92.15-15 be permitted than presently exists.
Subpart 92.20--Accommodations for Officers and Crew
Source: CGD 95-027, 61 FR 26005, May 23, 1996, unless otherwise
noted.
Sec. 92.20-1 Application.
(a) The provisions of this subpart apply to all vessels of 100 gross
tons and over contracted for on or after November 19, 1952. Vessels of
100 gross tons and over contracted for prior to November 19, 1952 must
meet the requirements of Sec. 92.20-90.
(b) Vessels of less than 100 gross tons must meet the applicable
requirements of this subpart insofar as is reasonable and practicable.
Sec. 92.20-5 Intent.
It is the intent of this subpart that the accommodations provided
for officers and crew on all vessels must be securely constructed,
properly lighted, heated, drained, ventilated, equipped, located,
arranged, and insulated from undue noise, heat, and odors.
Sec. 92.20-10 Location of crew spaces.
(a) Crew quarters must not be located farther forward in the vessel
than a vertical plane located at 5 percent of the vessel's length abaft
the forward side of the stem at the designed summer load water line.
However, for vessels in other than ocean or coastwise service, this
distance need not exceed 8.5 meters (28 feet). For the purposes of this
paragraph, the vessel's length must be as defined in Sec. 43.15-1 of
subchapter E (Load Lines) of this chapter. Unless approved by the
Commandant, no section of the deck head of the crew spaces may be below
the deepest load line.
(b) There must be no direct communication, except through solid,
close fitted doors, or hatches between crew spaces and chain lockers, or
machinery spaces.
Sec. 92.20-15 Construction.
All crew spaces are to be constructed and arranged in a manner
suitable to the purpose for which they are intended and so that they can
be kept in a clean, workable, and sanitary condition.
Sec. 92.20-20 Sleeping accommodations.
(a) Where practicable, each licensed officer must be provided with a
separate stateroom.
(b) Sleeping accommodations for the crew must be divided into rooms,
no one of which shall berth more than 4 persons.
(c) Each room must be of such size that there is at least 2.78
square meters (30 square feet) of deck area and a volume of at least 5.8
cubic meters (210 cubic feet) for each person accommodated. The clear
head room must be
[[Page 43]]
not less than 190 centimeters (75 inches). In measuring sleeping
accommodations, any furnishings contained therein for the use of the
occupants are not to be deducted from the total volume or from the deck
area.
(d) Each person shall have a separate berth and not more than one
berth may be placed above another. The berth must be composed of
materials not likely to corrode. The overall size of a berth must not be
less than 68 centimeters (27 inches) wide by 190 centimeters (75 inches)
long, except by special permission of the Commandant. Where 2 tiers of
berths are fitted, the bottom of the lower berth must not be less than
30 centimeters (12 inches) above the deck. The berths must not be
obstructed by pipes, ventilating ducts, or other installations.
(e) A locker must be provided for each person accommodated in a
room.
Sec. 92.20-25 Washrooms and toilet rooms.
(a) There must be provided at least 1 toilet, 1 washbasin, and 1
shower or bathtub for each 8 members or portion thereof in the crew who
do not occupy rooms to which private or semi-private facilities are
attached.
(b) The toilet rooms and washrooms must be located convenient to the
sleeping quarters of the crew to which they are allotted but must not
open directly into such quarters except when they are provided as
private or semi-private facilities.
(c) All washbasins, showers, and bathtubs shall be equipped with
adequate plumbing, including hot and cold running water. All toilets
must be installed with adequate plumbing for flushing.
(d) At least 1 washbasin must be fitted in each toilet room, except
where private or semi-private facilities are provided and washbasins are
installed in the sleeping rooms.
(e) Where more than 1 toilet is located in a space or compartment,
each toilet must be separated by partitions.
Sec. 92.20-30 Messrooms.
(a) Messrooms must be located as near to the galley as is
practicable except where the messroom is equipped with a steam table.
(b) Each messroom must seat the number of persons expected to eat in
the messroom at one time.
Sec. 92.20-35 Hospital space.
(a) Each vessel which in the ordinary course of its trade makes
voyages of more than 3 days duration between ports and which carries a
crew of 12 or more, must be provided with a hospital space. This space
must be situated with due regard to the comfort of the sick so that they
may receive proper attention in all weathers.
(b) The hospital must be suitably separated from other spaces and
must be used for the care of the sick and for no other purpose.
(c) The hospital must be fitted with berths in the ratio of 1 berth
to every 12 members of the crew or portion thereof who are not berthed
in single occupancy rooms, but the number of berths need not exceed 6.
(d) The hospital must have a toilet, washbasin, and bathtub or
shower conveniently situated. Other necessary suitable equipment such as
a clothes locker, a table, and a seat shall be provided.
(e) On vessels in which the crew is berthed in single occupancy
rooms, a hospital space will not be required, provided that one room is
designated and fitted for use as a treatment or isolation room. This
room must meet the following standards:
(1) The room must be available for immediate medical use; and
(2) A washbasin with hot and cold running water must be installed
either in or immediately adjacent to the space and other required
sanitary facilities must be conveniently located.
Sec. 92.20-40 Other spaces.
Each vessel must have--
(a) Sufficient facilities where the crew may wash and dry their own
clothes, including at least 1 sink supplied with hot and cold fresh
water;
(b) Recreation spaces; and
(c) A space or spaces of adequate size on an open deck to which the
crew has access when off duty.
[CGD 95-027, 61 FR 26005, May 23, 1996; 61 FR 32900, June 25, 1996]
[[Page 44]]
Sec. 92.20-45 Lighting.
Each berth must have a light.
Sec. 92.20-50 Heating and cooling.
(a) All manned spaces must be adequately heated and cooled in a
manner suitable to the purpose of the space.
(b) The heating and cooling system for accommodations must be
capable of maintaining a temperature of 21 deg. C (70 deg. F) under
normal operating conditions without curtailing ventilation.
(c) Radiators and other heating apparatus must be so placed and
shielded, where necessary, to avoid risk of fire, danger, or discomfort
to the occupants. Pipes leading to radiators or heating apparatus must
be insulated where those pipes create a hazard to persons occupying the
space.
Sec. 92.20-55 Insect screens.
Provisions must be made to protect the crew quarters against the
admission of insects.
Sec. 92.20-90 Vessels contracted for prior to November 19, 1952.
(a) Vessels of less than 100 gross tons, contracted for prior to
November 19, 1952, must meet the general intent of Sec. 92.20-5 and in
addition must meet the following requirements:
(1) Existing structure, arrangements, materials, and facilities,
previously accepted or approved will be considered satisfactory so long
as they are maintained in a suitable condition to the satisfaction of
the Officer in Charge, Marine Inspection.
(2) Minor repairs and alterations may be made to the same standard
as the original construction.
(b) Vessels of 100 gross tons and over, contracted for prior to
March 4, 1915, must meet the following requirements:
(1) Existing structure, arrangements, materials, and facilities,
previously approved will be considered satisfactory so long as they are
maintained in good condition to the satisfaction of the Officer in
Charge, Marine Inspection.
(2) Minor repairs and alterations may be made to the same standard
as the original construction, provided that in no case will a greater
departure from the standards of Secs. 92.20-5 through 92.20-55 be
permitted than presently exists.
(c) Vessels of 100 gross tons and over, contracted for on or after
March 4, 1915, but prior to January 1, 1941, must meet the following
requirements:
(1) Existing structure, arrangements, materials, and facilities,
previously approved will be considered satisfactory so long as they are
maintained in a suitable condition to the satisfaction of the Officer in
Charge, Marine Inspection. Minor repairs and alterations may be made to
the same standard as the original construction.
(2) Each vessel, which in the ordinary course of its trade makes a
voyage of more than 3 days duration between ports and which carries a
crew of 12 or more persons, must be provided with a suitable hospital
space for the exclusive use of the sick or injured.
(3) The crew spaces must be securely constructed, properly lighted,
heated, drained, ventilated, equipped, located, arranged, and insulated
from undue noise, heat, and odors.
(d) Vessels of 100 gross tons and over, contracted for on or after
January 1, 1941, but prior to November 19, 1952, must meet the following
requirements:
(1) Existing structure, arrangements, materials, and facilities,
previously approved will be considered satisfactory so long as they are
maintained in a suitable condition to the satisfaction of the Officer in
Charge, Marine Inspection. Minor repairs and alterations may be made to
the same standard as the original construction.
(2) Washbasins, showers, and bathtubs if substituted for showers,
must be equipped with adequate plumbing including hot and cold running
water.
(3) Each crewmember must have a separate berth, and berths may not
be placed more than 2 high.
(4) Each vessel, which in the ordinary course of its trade makes a
voyage of more than 3 days duration between ports and which carries a
crew of 12 or more persons, must be provided with a suitable hospital
space for the exclusive use of the sick or injured. Berths shall be
provided in the ratio of 1 berth for each 12 members of the crew or
fraction thereof, but the number of berths need not exceed 6.
(5) The crew spaces must be securely constructed, properly lighted,
heated, drained, ventilated, equipped, located,
[[Page 45]]
arranged, and insulated from undue noise, heat, and odors.
Subpart 92.25--Rails and Guards
Sec. 92.25-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 92.25-90, shall apply to all vessels contracted for on or after
July 1, 1969. Vessels contracted for prior to July 1, 1969, shall meet
the requirements of Sec. 92.25-90.
[CGFR 65-50, 30 FR 16983, Dec. 30, 1965, as amended by CGFR 69-72, 34 FR
17484, Oct. 29, 1969; CGD 80-120, 47 FR 5723, Feb. 8, 1982]
Sec. 92.25-5 Where rails required.
(a) All vessels shall have efficient guard rails or bulwarks on
decks and bridges. The height of rails or bulwarks shall be at least
39\1/2\ inches from the deck except that where this height would
interfere with the normal operation of the vessel, a lesser height may
be approved by the Commandant. At exposed peripheries of the freeboard
and superstructure decks, the rails shall be in at least three courses,
including the top. The opening below the lowest course shall not be more
than 9 inches. The courses shall not be more than 15 inches apart. In
the case of ships with rounded gunwales the guard rail supports shall be
placed on the flat of the deck. On other decks and bridges the rails
shall be in at least two courses, including the top, approximately
evenly spaced. If it can be shown to the satisfaction of the Officer in
Charge, Marine Inspection, that the installation of rails of such height
will be unreasonable and impracticable, having regard to the business of
the vessel, rails of a lesser height or in some cases grab rails may be
accepted and inboard rails may be eliminated if the deck is not
generally accessible.
(b) Where it can be shown to the satisfaction of the Commandant that
a vessel is engaged exclusively in voyages of a sheltered nature, the
provisions of paragraph (a) of this section may be relaxed.
[CGFR 69-72, 34 FR 17484, Oct. 29, 1969, as amended by CGD 80-120, 47 FR
5723, Feb. 8, 1982]
Sec. 92.25-10 Storm rails.
(a) On vessels in ocean and coastwise service, suitable storm rails
shall be installed in all passageways and at the deckhouse sides where
persons on board might have normal access. Storm rails shall be
installed on both sides of passageways which are 6 feet or more in
width.
Sec. 92.25-15 Guards in dangerous places.
(a) Suitable hand covers, guards, or rails shall be installed in way
of all exposed and dangerous places such as gears, machinery, etc.
Sec. 92.25-90 Vessels contracted for prior to July 1, 1969.
(a) Vessels contracted for prior to July 1, 1969, assigned a deeper
load line under part 42 of subchapter E (Load Lines) of this chapter
shall have efficient guard rails or bulwarks as required by Sec. 92.25-
5. Otherwise, existing structure, arrangements, materials, and
facilities previously approved will be considered satisfactory so long
as they are maintained in good condition to the satisfaction of the
Officer in Charge, Marine Inspection. Minor repairs and alterations may
be made to the same standards as the original construction. However, in
no case will greater departure from the standards of Secs. 92.25-5
through 92.25-15 be permitted than presently exists.
[CGFR 69-72, 34 FR 17484, Oct. 29, 1969, as amended by CGD 80-120, 47 FR
5723, Feb. 8, 1982]
PART 93--STABILITY--Table of Contents
Subpart 93.01--Application
Sec.
93.01-1 General.
Subpart 93.01--Application
Sec. 93.01-1 General.
Each vessel must meet the applicable requirements in subchapter S of
this chapter.
[CGD 79-023, 48 FR 51008, Nov. 4, 1983]
[[Page 46]]
PART 95--FIRE PROTECTION EQUIPMENT--Table of Contents
Subpart 95.01--Application
Sec.
95.01-1 General.
95.01-2 Incorporation by reference.
95.01-5 Equipment installed but not required.
Subpart 95.05--Fire Detecting and Extinguishing Equipment, Where
Required
95.05-1 Fire detecting, manual alarm, and supervised patrol systems.
95.05-5 Fire main system.
95.05-10 Fixed fire extinguishing systems.
95.05-15 Hand portable fire extinguishers and semiportable fire
extinguishing systems.
Subpart 95.10--Fire Main System, Details
95.10-1 Application.
95.10-5 Fire pumps.
95.10-10 Fire hydrants and hose.
95.10-15 Piping.
95.10-90 Installations contracted for prior to May 26, 1965.
Subpart 95.13--Steam Smothering Systems
95.13-1 Application.
Subpart 95.15--Carbon Dioxide Extinguishing Systems, Details
95.15-1 Application.
95.15-5 Quantity, pipe sizes, and discharge rates.
95.15-10 Controls.
95.15-15 Piping.
95.15-20 Carbon dioxide storage.
95.15-25 Discharge outlets.
95.15-30 Alarms.
95.15-35 Enclosure openings.
95.15-40 Pressure relief.
95.15-90 Installations contracted for prior to November 19, 1952.
Subpart 95.17--Foam Extinguishing Systems, Details
95.17-1 Application.
95.17-5 Quantity of foam required.
95.17-10 Controls.
95.17-15 Piping.
95.17-20 Discharge outlets.
95.17-25 Additional protection required.
95.17-90 Installations contracted for prior to November 19, 1952.
Subpart 95.30--Automatic Sprinkler Systems, Details
95.30-1 Application.
Subpart 95.50--Hand Portable Fire Extinguishers and Semiportable Fire
Extinguishing Systems, Arrangements and Details
95.50-1 Application.
95.50-5 Classification.
95.50-10 Location.
95.50-15 Spare charges.
95.50-20 Semiportable fire extinguishers.
95.50-90 Vessels contracted for prior to November 19, 1952.
Subpart 95.60--Fire Axes
95.60-1 Application.
95.60-5 Number required.
95.60-10 Location.
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
Source: CGFR 65-50, 30 FR 17001, Dec. 30, 1965, unless otherwise
noted.
Subpart 95.01--Application
Sec. 95.01-1 General.
(a) The provisions of this part shall apply to all vessels except as
specifically noted in this part.
Sec. 95.01-2 Incorporation by reference.
(a) Certain material is incorporated by reference into this part
with the approval of the Director of the Federal Register in accordance
with 5 U.S.C. 552(a). To enforce any edition other than that specified
in paragraph (b) of this section, the Coast Guard must publish notice of
change in the Federal Register and make the material available to the
public. All approved material is on file at the Office of the Federal
Register, 800 North Capitol Street, NW., suite 700, Washington, DC, and
at the U.S. Coast Guard, Office of Design and Engineering Standards (G-
MSE), 2100 Second Street SW., Washington, DC 20593-0001 and is available
from the sources indicated in paragraph (b) of this section.
(b) The material approved for incorporation by reference in this
part and the sections affected are:
American Society for Testing and Materials (ASTM)
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
ASTM F 1121-87 (1993), Standard Specification for International Shore
Connections for Marine Fire Applications--95.10-10
[[Page 47]]
National Fire Protection Association (NFPA)
1 Batterymarch Park, Quincy, MA 02269-9101.
NFPA 13-1996, Standard for the Installation of Sprinkler Systems--95.30-
1
[CGD 88-032, 56 FR 35825, July 29, 1991, as amended by CGD 95-072, 60 FR
50464, Sept. 29, 1995; CGD 96-041, 61 FR 50729, Sept. 27, 1996; CGD 97-
057, 62 FR 51045, Sept. 30, 1997; CGD 95-028, 62 FR 51206, Sept. 30,
1997; USCG 1999-5151, 64 FR 67181, Dec. 1, 1999]
Sec. 95.01-5 Equipment installed but not required.
(a) Where fire detecting or extinguishing systems or equipment are
not required, but are installed, the system or equipment and its
installation shall meet the requirements of this part.
Subpart 95.05--Fire Detecting and Extinguishing Equipment, Where
Required
Sec. 95.05-1 Fire detecting, manual alarm, and supervised patrol systems.
(a) Fire detecting, manual alarm, and supervised patrol systems are
not required except in special cases; but if installed, the systems
shall meet the applicable requirements of part 76 of subchapter H
(Passenger Vessels) of this chapter.
(b) In each compartment containing explosives, and in adjacent cargo
compartments, there shall be provided a smoke detecting or other
suitable type fire detecting system.
(c) Enclosed spaces which are ``specially suitable for vehicles''
shall be fitted with an approved fire or smoke detecting system.
[CGFR 66-33, 31 FR 15285, Dec. 6, 1966]
Sec. 95.05-5 Fire main system.
(a) Fire pumps, hydrants, hose, and nozzles shall be installed on
the following vessels:
(1) On all self-propelled vessels.
(2) On all barges with sleeping accommodations for more than 12
persons.
(b) The arrangements and details of the fire main system shall be as
set forth in subpart 95.10.
Sec. 95.05-10 Fixed fire extinguishing systems.
(a) Approved fire extinguishing systems may be used or required in
locations delineated in this section on the following vessels.
Previously approved installations may be retained as long as they are
maintained in good condition to the satisfaction of the Officer in
Charge, Marine Inspection.
(1) On all self-propelled vessels other than yachts and fishing
vessels.
(2) On all barges with sleeping accommodations for more than 12
persons.
(b) A fixed carbon dioxide or other approved system must be
installed in all cargo compartments and tanks for combustible cargo,
except for vessels engaged exclusively in the carriage of coal or grain
in bulk. For cargo compartments and tanks fitted with a fixed carbon
dioxide or other approved system a deck foam system is not required,
instead of the carbon dioxide system or other approved system, the
following systems may be used or required in special cases:
(1) A fixed foam system may be used in cargo tanks.
(2) A water sprinkling system may be required, and the details of
such system will be subject to special approval, in cases where a cargo
is normally accessible and is considered to be a part of the working or
living quarters.
(3) Spaces ``specially suitable for vehicles'' must be fitted with
an approved carbon dioxide system. Alternately, the Commandant may
permit the installation of an approved water sprinkler system or other
suitable system.
(c) On vessels other than motorboats, a fixed carbon dioxide or
other approved system must be installed in all lamp and paint lockers,
oil rooms, and similar spaces.
(d) On vessels of 1,000 gross tons and over, contracted for on or
after November 19, 1952, or where conversion from coal to oil is
contracted for on or after November 19, 1952, a fixed carbon dioxide,
foam, or water spray system shall be installed in all spaces containing
oil fired boilers, either main or auxiliary, or their fuel oil units,
valves, or manifolds in the line between the settling tanks and the
boilers.
(e) Fire extinguishing systems shall be provided for internal
combustion installations in accordance with the following:
(1) If a fixed fire-extinguishing system is installed to protect an
internal
[[Page 48]]
combustion propelling machinery installation, the system shall be of the
carbon dioxide type.
(2) On vessels of 1,000 gross tons and over on an international
voyage, the construction or conversion of which is contracted for on or
after May 26, 1965, a fixed carbon dioxide system shall be installed in
all spaces containing internal combustion or gas turbine main propulsion
machinery, auxiliaries with an aggregate power of 1,000 b. hp. or
greater, or their fuel oil units, including purifiers, valves, and
manifolds.
(3) On vessels, the construction, conversion or automation of which
is contracted for on or after July 1, 1968, the systems shall be in
accordance with the following:
(i) A fixed carbon dioxide system shall be installed in any space
containing machinery using fuel having a flashpoint of less than
110 deg. F.
(ii) On vessels of 1,000 gross tons and over, a fixed carbon dioxide
system shall be installed in all spaces containing internal combustion
or gas turbine main propulsion machinery, auxiliaries with an aggregate
power of 1,000 b. hp. or greater, or their fuel oil units, including
purifiers, valves, and manifolds.
(f) On vessels contracted for on or after November 19, 1952, where
an enclosed ventilating system is installed for electric propulsion
motors or generators, a fixed carbon dioxide extinguishing system shall
be installed in such system.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGFR 66-33, 31 FR
15285, Dec. 6, 1966; CGFR 67-90, 33 FR 1016, Jan. 26, 1968; CGD 95-027,
61 FR 26006, May 23, 1996]
Sec. 95.05-15 Hand portable fire extinguishers and semiportable fire extinguishing systems.
(a) Approved hand portable fire extinguishers and semiportable fire
extinguishing systems shall be installed on all vessels, other than
unmanned barges and fishing vessels, as set forth in subpart 95.50.
Subpart 95.10--Fire Main System, Details
Sec. 95.10-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 95.10-90, shall apply to all fire main installations contracted for
on or after May 26, 1965. Installations contracted for prior to May 26,
1965, shall meet the requirements of Sec. 95.10-90.
Sec. 95.10-5 Fire pumps.
(a) Vessels shall be equipped with independently driven fire pumps
in accordance with Table 95.10-5(a).
Table 95.10-5(a)
------------------------------------------------------------------------
Gross tons Hose and Nozzle
------------------------- Minimum hydrant orifice Length of
number of size, size, hose feet
Over Not over pumps inches inches
------------------------------------------------------------------------
100 \1\ 1 \1\ 1\1/2\ \1\ \1/2\ \1\ 50
100 1,000 1 1\1/2\ \5/8\ 50
1,000 1,500 2 1\1/2\ \5/8\ 50
1,500 ........... 2 \2\ 2\1/2\ \2\ \7/8\ \2\ 50
------------------------------------------------------------------------
\1\ On vessels of 65 feet in length or less, \3/4\-inch hose of good
commercial grade together with a commercial garden hose nozzle may be
used. The pump may be hand operated and the length of hose shall be
sufficient to assure coverage of all parts of the vessel.
\2\ 75 feet of 1\1/2\-inch hose and \5/8\-inch nozzle may be used where
specified by Sec. 95.10-10(b) for interior locations and 50 feet of
1\1/2\-inch hose may be used in exterior locations on vessels in other
than ocean or coastwise service.
(b) On vessels of 1,000 gross tons and over on an international
voyage, each required fire pump, while delivering water thru the fire
main system at a pressure corresponding to that required by paragraph
(c) of this section, shall have a minimum capacity of at least two-
thirds of that required for an independent bilge pump. However, in no
case shall the capacity of each fire pump be less than that otherwise
required by this section.
(c) Each pump shall be capable of delivering water simultaneously
from the two highest outlets at a Pitot tube pressure of approximately
50 p.s.i. Where 1\1/2\-inch hose is permitted in lieu of 2\1/2\-inch
hose by footnote 2 of Table 95.10-5(a), the pump capacity shall be
determined on the same basis as if 2\1/2\-inch hose had been permitted.
Where \3/4\-inch hose is permitted by Table
[[Page 49]]
95.10-5(a), the Pitot tube pressure need be only 35 p.s.i.
(d) Fire pumps shall be fitted on the discharge side with relief
valves set to relieve at 25 p.s.i. in excess of the pressure necessary
to maintain the requirements of paragraph (c) of this section or 125
p.s.i., whichever is greater. Relief valves may be omitted if the pumps,
operating under shut-off conditions, are not capable of developing a
pressure exceeding this amount.
(e) Fire pumps shall be fitted with a pressure gage on the discharge
side of the pumps.
(f) Fire pumps may be used for other purposes provided at least one
of the required pumps is kept available for use on the fire system at
all times. In no case shall a pump having connection to an oil line be
used as a fire pump. Branch lines connected to the fire main for
purposes other than fire and deck wash shall be so arranged that
adequate water can be made continuously available for firefighting
purposes.
(g) The total area of the pipes leading from a pump shall not be
less than the discharge area of the pump.
(h) On vessels with oil fired boilers, either main or auxiliary, or
with internal combustion propulsion machinery, where 2 fire pumps are
required, they shall be located in separate spaces, and the arrangement
of pumps, sea connections, and sources of power shall be such as to
insure that a fire in any one space will not put all of the fire pumps
out of operation. However, where it is shown to the satisfaction of the
Commandant that it is unreasonable or impracticable to meet this
requirement due to the size or arrangement of the vessel, or for other
reasons, the installation of a total flooding carbon dioxide system may
be accepted as an alternate method of extinguishing any fire which would
affect the powering and operation of at least one of the required fire
pumps.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGFR 66-33, 31 FR
15285, Dec. 6, 1966; CGD 95-028, 62 FR 51206, Sept. 30, 1997]
Sec. 95.10-10 Fire hydrants and hose.
(a) The size of fire hydrants, hose, and nozzles and the length of
hose required shall be as noted in Table 95.10-5(a).
(b) In lieu of the 2\1/2\-inch hose and hydrants specified in Table
95.10-5(a), on vessels over 1,500 gross tons, the hydrants in interior
locations may have siamese connections for 1\1/2\-inch hose. In these
cases the hose shall be 75 feet in length, and only one hose will be
required at each fire station; however, if all such stations can be
satisfactorily served with 50-foot lengths, 50-foot hose may be used.
(c) On vessels of 500 gross tons and over there must be at least one
shore connection to the fire main available to each side of the vessel
in an accessible location. Suitable cut-out valves and check valves must
be provided. Suitable adapters also must be provided for furnishing the
vessel's shore connections with couplings mating those on the shore fire
lines. Vessels of 500 gross tons and over on an international voyage,
must be provided with at least one international shore connection
complying with ASTM F 1121 (incorporated by reference, see Sec. 95.01-
2). Facilities must be available enabling an international connection to
be used on either side of the vessel.
(d) Fire hydrants shall be of sufficient number and so located that
any part of the vessel, other than main machinery spaces, accessible to
persons on board while the vessel is being navigated and all cargo holds
may be reached with at least 2 streams of water from separate outlets,
at least one of which shall be from a single length of hose. In main
machinery spaces, all portions of such spaces shall be capable of being
reached by at least 2 streams of water, each of which shall be from a
single length of hose from separate outlets; however, this requirement
need not apply to shaft alleys containing no assigned space for the
stowage of combustibles. Fire hydrants shall be numbered as required by
Sec. 97.37-15 of this subchapter.
(e) All parts of the fire main located on exposed decks shall either
be protected against freezing or be fitted with cut-out valves and drain
valves so that the entire exposed parts of such piping may be shut off
and drained in freezing weather. Except when closed to prevent freezing,
such valves shall be sealed open.
[[Page 50]]
(f) The outlet at the fire hydrant shall be limited to any position
from the horizontal to the vertical pointing downward, so that the hose
will lead horizontally or downward to minimize the possibility of
kinking.
(g) Each fire hydrant must have at least one length of firehose, a
spanner, and a hose rack or other device for stowing the hose.
(h) Fire hose shall be connected to the outlets at all times.
However, on open decks where no protection is afforded to the hose in
heavy weather, or where the hose may be liable to damage from the
handling of cargo, the hose may be temporarily removed from the hydrant
and stowed in an accessible nearby location.
(i) Each firehose on each hydrant must have a combination solid
stream and water spray firehose nozzle approved under subpart 162.027 of
this chapter. Firehose nozzles previously approved under subpart 162.027
of this chapter may be retained so long as they are maintained in good
condition to the satisfaction of the Officer in Charge, Marine
Inspection.
(j) In each propulsion machinery space containing an oil fired
boiler, internal combustion machinery, or oil fuel unit on a vessel on
an international voyage or of 1000 gross tons or more, each firehose
having a combination nozzle previously approved under subpart 162.027 of
this chapter must have a low-velocity water spray applicator that is
also previously approved under subpart 162.027 of this chapter. The
length of the applicator must be less than 1.8 meters (6 feet).
(k) Fixed brackets, hooks, or other means for stowing an applicator
must be next to each fire hydrant that has an applicator under paragraph
(j) of this section.
(l) Firehose shall not be used for any other purpose than fire
extinguishing, drills, and testing.
(m) Fire hydrants, nozzles, and other fittings shall have threads to
accommodate the hose connections noted in paragraph (l) of this section.
(n) Firehose and couplings must be as follows:
(1) Fire station hydrant connections shall be brass, bronze, or
other equivalent metal. Couplings shall either:
(i) Use National Standard fire hose coupling threads for the 1\1/2\
inch (38 millimeter) and 2\1/2\ inch (64 millimeter) hose sizes, i.e., 9
threads per inch for 1\1/2\ inch hose, and 7\1/2\ threads per inch for
2\1/2\ inch hose; or
(ii) Be a uniform design for each hose diameter throughout the
vessel.
(2) Where 19 millimeters (\3/4\ inch) hose is permitted by table
95.10-5(a), the hose and couplings shall be of good commercial grade.
(3) Each section of firehose must be lined commercial firehose that
conforms to Underwriters' Laboratories, Inc. Standard 19 or Federal
Specification ZZ-H-451E. Hose that bears the label of Underwriters'
Laboratories, Inc. as lined firehose is accepted as conforming to this
requirement.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGD 74-60, 41 FR
43151, Sept. 30, 1976; CGD 76-086, 44 FR 2392, Jan. 11, 1979; CGD 88-
032, 56 FR 35826, July 29, 1991; CGD 95-012, 60 FR 48051, Sept. 18,
1995; CGD 95-027, 61 FR 26007, May 23, 1996; CGD 95-028, 62 FR 51206,
Sept. 30, 1997; USCG-2000-7790, 65 FR 58461, Sept. 29, 2000]
Sec. 95.10-15 Piping.
(a) All piping, valves, and fittings shall meet the applicable
requirements of subchapter F (Marine Engineering) of this chapter.
(b) All distribution cut-off valves shall be marked as required by
Sec. 97.37-10 of this subchapter.
(c) For vessels on an international voyage, the diameter of the fire
main shall be sufficient for the effective distribution of the maximum
required discharge from two fire pumps operating simultaneously. This
requirement is in addition to Sec. 95.10-5(c). The discharge of this
quantity of water through hoses and nozzles at a sufficient number of
adjacent hydrants shall be at a minimum Pitot tube pressure of
approximately 50 pounds per square inch.
Sec. 95.10-90 Installations contracted for prior to May 26, 1965.
Installations contracted for prior to May 26, 1965, shall meet the
following requirements:
(a) Except as specifically modified by this paragraph, the
requirements of Secs. 95.10-5 through 95.10-15 shall be complied with
insofar as the number and
[[Page 51]]
general type of equipment is concerned. Existing equipment, except
firehose nozzles and low-velocity water spray applicators, previously
approved, but not meeting the applicable requirements of Secs. 95.10-5
through 95.10-15 may be continued in service so long as they are
maintained in good condition to the satisfaction of the Officer in
Charge, Marine Inspection. Minor repairs, alterations, and replacements
may be permitted to the same standards as the original installations.
However, all new installations or major replacements shall meet the
applicable requirements in this subpart.
(b) All vessels contracted for prior to November 19, 1952, other
than motorboats, shall be fitted with fire pumps, hoses, and nozzles in
accordance with Table 95.10-90(a)(2).
Table 95.10-90(a)(2)
------------------------------------------------------------------------
Gross tons Minimum
------------------------- Minimum hose and Nozzle
number of hydrant orifice Length of
Over Not over pumps size, size, hose feet
inches inches
------------------------------------------------------------------------
100 1 \1\ 1\1/2\ \1\ \5/16\ \1\ 50
100 1,000 1 \2\ 1\1/2\ \2\ \5/8\ \2\ 50
1,000 ........... 2 \2\ 1\1/2\ \2\ \5/8\ \2\ 50
------------------------------------------------------------------------
\1\ On vessels of 65 feet in length or less, \3/4\-inch hose of good
commercial grade together with a commercial garden hose nozzle may be
used. The pump may be hand operated and the length of hose shall be
sufficient to assure coverage of all parts of the vessel.
\2\ May use 50 feet of 2\1/2\-inch hose with \7/8\-inch nozzles for
exterior stations. 75 feet of 1\1/2\-inch hose with \5/8\-inch nozzles
may be used for interior station in which case such interior stations
shall have siamese connections.
(c) Vessels contracted for prior to July 1, 1935, need not meet the
requirements of Sec. 95.10-5(h), and vessels contracted for on or after
July 1, 1935, but prior to November 19, 1952, may have a carbon dioxide
``bilge'' in lieu of ``total flooding'' system. However, in vessels of
both categories where a conversion from coal to oil is contracted for on
or after November 19, 1952, the provisions of Sec. 95.10-5(h) shall
apply.
(d) The general requirements of Sec. 95.10-5(c) through (g),
Sec. 95.10-10(d) through (i), and Sec. 95.10-15 shall be complied with
insofar as is reasonable and practicable.
(e) Firehose nozzles and low-velocity spray applicators must meet
the requirements of 95.10-10(i), 95.10-10(j), and 95.10-10(k).
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGD 76-086, 44 FR
2392, Jan. 11, 1979; CGD 95-027, 61 FR 26007, May 23, 1996]
Subpart 95.13--Steam Smothering Systems
Sec. 95.13-1 Application.
Steam smothering systems are not permitted on vessels contracted for
on or after January 1, 1962. Previously approved installations may be
retained as long as they are maintained in good condition to the
satisfaction of the Officer in Charge, Marine Inspection.
[CGD 95-027, 61 FR 26007, May 23, 1996]
Subpart 95.15--Carbon Dioxide Extinguishing Systems, Details
Sec. 95.15-1 Application.
(a) Where a carbon dioxide extinguishing system is installed, the
provisions of this subpart, with the exception of Sec. 95.15-90, shall
apply to all installations contracted for on or after November 19, 1952.
Installations contracted for prior to November 19, 1952, shall meet the
requirements of Sec. 95.15-90.
(b) The requirements of this subpart are based on a ``high pressure
system,'' i.e., one in which the carbon dioxide is stored in liquid form
at atmospheric temperature. Details for ``low pressure systems,'' i. e.,
those in which the carbon dioxide is stored in liquid form at a
continuously controlled low temperature, may be specifically approved by
the Commandant where it is demonstrated that a comparable degree of
safety and fire extinguishing ability is achieved.
Sec. 95.15-5 Quantity, pipe sizes, and discharge rates.
(a) General. The amount of carbon dioxide required for each space
shall be as determined by paragraphs (b) through (d) of this section.
(b) Total available supply. A separate supply of carbon dioxide need
not be provided for each space protected. The total available supply
shall be at least sufficient for the space requiring the greatest
amount.
[[Page 52]]
(c) Cargo spaces. (1) The number of pounds of carbon dioxide
required for each space shall be equal to the gross volume of the space
in cubic feet divided by 30.
(2) Although separate piping shall be led to each cargo hold and
'tween deck, for the purpose of determining the amount of carbon dioxide
required, a cargo compartment will be considered as the space between
watertight or firescreen bulkheads and from the tank top or lowest deck
to the deck head of the uppermost space on which cargo may be carried.
If a trunk extends beyond such deck, the trunk volume shall be included.
Tonnage openings shall be considered as sealed for this purpose.
(3) Branch lines to the various cargo holds and 'tween decks shall
not be less than \3/4\-inch standard pipe size.
(4) No specific discharge rate need be applied to such systems.
(d) Machinery spaces, paint lockers, tanks, and similar spaces. (1)
Except as provided in paragraph (d)(3) of this section, the number of
pounds of carbon dioxide required for each space shall be equal to the
gross volume of the space divided by the appropriate factor noted in
Table 95.15-5(d)(1). If fuel can drain from the compartment being
protected to an adjacent compartment, or if the compartments are not
entirely separate, the requirements for both compartments shall be used
to determine the amount of carbon dioxide to be provided. The carbon
dioxide shall be arranged to discharge into both such compartments
simultaneously.
Table 95.15-5(d)(1)
------------------------------------------------------------------------
Gross volume of compartment, cubic feet
------------------------------------------------- Factor
Over-- Not over--
------------------------------------------------------------------------
....................... ......................
500 ....................... 15
500 1,600 16
1,600 4,500 18
4,500 50,000 20
50,000 ....................... 22
------------------------------------------------------------------------
(2) For the purpose of the requirements of this paragraph, the
volume of the machinery space shall be taken as exclusive of the normal
machinery casing unless the boiler, internal combustion machinery, or
fuel oil installation extend into such space, in which case the volume
shall be taken to the top of the casing or the next material reduction
in casing area, whichever is lower. For installations contracted for on
or after October 1, 1959, ``normal machinery casing'' and ``material
reduction in casing area'' shall be defined as follows:
(i) By ``normal machinery casing'' shall be meant a casing the area
of which is not more than 40 percent of the maximum area of the
machinery space.
(ii) By ``material reduction in casing area'' shall be meant a
reduction to at least 40 percent of the casing area.
(3) For vessels on an international voyage contracted for on or
after May 26, 1965, the amount of carbon dioxide required for a space
containing propulsion boilers or internal combustion propulsion
machinery shall be as given by paragraphs (d) (1) and (2) of this
section or by dividing the entire volume, including the casing, by a
factor of 25, whichever is the larger.
(4) Branch lines to the various spaces shall be as noted in Table
95.15-5(d)(4).
Table 95.15-5(d)(4)
------------------------------------------------------------------------
Maximum quantity
Maximum quantity Minimum pipe of carbon Minimum pipe
of carbon dioxide size, inches dioxide size, inches
required, pounds required, pounds
------------------------------------------------------------------------
100 \1/2\ 2,500 2\1/2\
225 \3/4\ 4,450 3
300 1 7,100 3\1/2\
600 1\1/4\ 10,450 4
1,000 1\1/2\ 15,000 4\1/2\
2,450 2 ................ ................
------------------------------------------------------------------------
(5) Distribution piping within the space shall be proportioned from
the supply line to give proper distribution to the outlets without
throttling.
(6) The number, type, and location of discharge outlets shall be
such as to give a uniform distribution throughout the space.
(7) The total area of all discharge outlets shall not exceed 85
percent nor be less than 35 percent of the nominal cylinder outlet area
or the area of the supply pipe, whichever is smaller. The nominal
cylinder outlet area in square inches shall be determined by multiplying
the factor 0.0022 by the number of pounds of carbon dioxide required,
except that in no case shall this outlet area be less than 0.110 square
inches.
[[Page 53]]
(8) The discharge of at least 85 percent of the required amount of
carbon dioxide shall be complete within 2 minutes.
(e) Spaces specially suitable for vehicles. (1) The number of pounds
of carbon dioxide required shall be equal to the gross volume of the
largest ``tight'' space divided by 22. In no case, however, shall the
quantity be less than that required by paragraph (c)(2) of this section.
(2) The arrangement of valves and piping shall be such that the
required quantity of carbon dioxide may be discharged into any ``tight''
space. The discharge of the required quantity of carbon dioxide shall be
completed within 2 minutes.
(3) Except as noted in paragraphs (e) (1) and (2) of this section,
the requirements of paragraph (d) of this section shall apply.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGFR 66-33, 31 FR
15285, Dec. 6, 1966; CGD 95-028, 62 FR 51207, Sept. 30, 1997; USCG-1999-
6216, 64 FR 53226, Oct. 1, 1999]
Sec. 95.15-10 Controls.
(a) Except as noted in Sec. 95.15-20(b) all controls and valves for
the operation of the system shall be outside the space protected, and
shall not be located in any space that might be cut off or made
inaccessible in the event of fire in any of the spaces protected.
(b) If the same cylinders are used to protect more than one hazard,
a manifold with normally closed stop valves shall be used to direct the
carbon dioxide into the proper space. If cylinders are used to protect
only one hazard, a normally closed stop valve shall be installed between
the cylinders and the hazard except for systems of the type indicated in
Sec. 95.15-5(d) which contain not more than 300 pounds of carbon
dioxide.
(c) Distribution piping to the various cargo spaces shall be
controlled from not more than two stations. One of the stations
controlling the system for the main machinery space shall be located as
convenient as practicable to one of the main escapes from the space. All
control stations and the individual valves and controls shall be marked
as required by Secs. 97.37-10 and 97.37-13 of this subchapter.
(d) Systems of the type indicated in Sec. 95.15-5(d) shall be
actuated by one control operating the valve to the space and a separate
control releasing at least the required amount of carbon dioxide. These
two controls shall be located in a box or other enclosure clearly
identified for the particular space. Those systems installed without a
stop valve shall be operated by one control releasing at least the
required amount of carbon dioxide.
(e) Where provisions are made for the simultaneous release of a
given amount of carbon dioxide by operation of a remote control,
provisions shall also be made for manual control at the cylinders. Where
gas pressure from pilot cylinders is used as a means for releasing the
remaining cylinders, not less than two pilot cylinders shall be used for
systems consisting of more than two cylinders. Each of the pilot
cylinders shall be capable of manual control at the cylinder, but the
remaining cylinders need not be capable of individual manual control.
(f) Systems of the type indicated in Sec. 95.15-5(d), other than
systems for tanks, which are of more than 300 pounds of carbon dioxide,
shall be fitted with an approved delayed discharge so arranged that the
alarm will be sounded for at least 20 seconds before the carbon dioxide
is released into the space. Such systems of not more than 300 pounds of
carbon dioxide shall also have a similar delayed discharge, except for
those systems for tanks and for spaces which have a suitable horizontal
escape. This paragraph shall be applicable only to systems installed on
or after July 1, 1957.
(g) All distribution valves and controls shall be of an approved
type. All controls shall be suitably protected.
(h) Complete but simple instructions for the operation of the
systems must be located in a conspicuous place at or near all pull
boxes, stop valve controls and in the CO2 cylinder storage
room. On systems in which the CO2 cylinders are not within
the protected space, these instructions must also include a schematic
diagram of the system and instructions detailing alternate methods of
discharging the system should the manual release or stop valve controls
fail to operate. Each control valve
[[Page 54]]
to branch lines must be marked to indicate the related space served.
(i) If the space or enclosure containing the carbon dioxide supply
or controls is to be locked, a key to the space or enclosure shall be in
a break-glass-type box conspicuously located adjacent to the opening.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGD 74-100B, 40
FR 6209, Feb. 10, 1975; USCG-1999-6216, 64 FR 53226, Oct. 1, 1999]
Sec. 95.15-15 Piping.
(a) The piping, valves, and fittings shall have a bursting pressure
of not less than 6,000 pounds per square inch.
(b) All piping, in nominal sizes not over \3/4\ inch shall be at
least Schedule 40 (standard weight) and in nominal sizes over \3/4\
inch, shall be at least Schedule 80 (extra heavy).
(c) All piping, valves, and fittings of ferrous materials shall be
protected inside and outside against corrosion unless specifically
approved otherwise by the Commandant.
(d) A pressure relief valve or equivalent set to relieve between
2,400 and 2,800 pounds per square inch shall be installed in the
distributing manifold or such other location as to protect the piping in
the event that all branch line shut-off valves are closed.
(e) All dead-end lines shall extend at least 2 inches beyond the
last orifice and shall be closed with cap or plug.
(f) All piping, valves, and fittings shall be securely supported,
and where necessary, protected against injury.
(g) Drains and dirt traps shall be fitted where necessary to prevent
the accumulation of dirt or moisture. Drains and dirt traps shall be
located in accessible locations where possible.
(h) Piping shall be used for no other purpose except that it may be
incorporated with the fire-detecting system.
(i) Piping passing through living quarters shall not be fitted with
drains or other openings within such spaces.
(j) Installation test requirements are:
(1) Upon completion of the piping installation, and before the
cylinders are connected, a pressure test shall be applied as set forth
in this paragraph. Only carbon dioxide or other inert gas shall be used
for this test.
(2) The piping from the cylinders to the stop valves in the manifold
shall be subjected to a pressure of 1,000 pounds per square inch. With
no additional gas being introduced to the system, it shall be
demonstrated that the leakage of the system is such as not to permit a
pressure drop of more than 150 pounds per square inch per minute for a
2-minute period.
(3) The individual branch lines to the various spaces protected
shall be subjected to a test similar to that described in the preceding
paragraph with the exception that the pressure used shall be 600 pounds
per square inch in lieu of 1,000 pounds per square inch. For the purpose
of this test, the distribution piping shall be capped within the space
protected at the first joint ahead of the nozzles.
(4) In lieu of the tests prescribed in paragraphs (j) (1) through
(3) of this section, small independent systems protecting spaces such as
emergency generator rooms, lamp lockers, etc., may be tested by blowing
out the piping with air at a pressure of at least 100 pounds per square
inch.
Sec. 95.15-20 Carbon dioxide storage.
(a) Except as provided in paragraph (b) of this section, the
cylinders shall be located outside the spaces protected, and shall not
be located in any space that might be cut off or made inaccessible in
the event of a fire in any of the spaces protected.
(b) Systems of the type indicated in Sec. 95.15-5(d), consisting of
not more than 300 pounds of carbon dioxide, may have the cylinders
located within the space protected. If the cylinder stowage is within
the space protected, the system shall be arranged in an approved manner
to be automatically operated by a heat actuator within the space in
addition to the regular remote and local controls.
(c) The space containing the cylinders shall be properly ventilated
and designed to preclude an anticipated ambient temperature in excess of
130 degrees F.
(d) Cylinders shall be securely fastened and supported, and where
necessary, protected against injury.
(e) Cylinders shall be so mounted as to be readily accessible and
capable of
[[Page 55]]
easy removal for recharging and inspection. Provisions shall be
available for weighing the cylinders.
(f) Where subject to moisture, cylinders shall be so installed as to
provide a space of at least 2 inches between the flooring and the bottom
of the cylinders.
(g) Cylinders shall be mounted in an upright position or inclined
not more than 30 degrees from the vertical. However, cylinders which are
fitted with flexible or bent siphon tubes may be inclined not more than
80 degrees from the vertical.
(h) Where check valves are not fitted on each independent cylinder
discharge, plugs or caps shall be provided for closing outlets when
cylinders are removed for inspection or refilling.
(i) All cylinders used for storing carbon dioxide must be
fabricated, tested, and marked in accordance with Secs. 147.60 and
147.65 of this chapter.
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by CGD 84-044, 53 FR
7749, Mar. 10, 1988; USCG-1999-6216, 64 FR 53226, Oct. 1, 1999]
Sec. 95.15-25 Discharge outlets.
(a) Discharge outlets shall be of an approved type.
Sec. 95.15-30 Alarms.
(a) Spaces which are protected by a carbon dioxide extinguishing
system and are normally accessible to persons on board while the vessel
is being navigated, other than paint and lamp lockers and similar small
spaces, shall be fitted with an approved audible alarm in such spaces
which will be automatically sounded when the carbon dioxide is admitted
to the space. The alarm shall be conspicuously and centrally located and
shall be marked as required by Sec. 97.37-9 of this subchapter. For
systems installed on or after July 1, 1957, alarms will be mandatory
only for systems required to be fitted with a delayed discharge. Such
alarms shall be so arranged as to sound during the 20 second delay
period prior to the discharge of carbon dioxide into the space, and the
alarm shall depend on no source of power other than the carbon dioxide.
Sec. 95.15-35 Enclosure openings.
(a) Where mechanical ventilation is provided for spaces other than
cargo and similar spaces which are protected by a carbon dioxide
extinguishing system, provisions shall be made so that the ventilation
system is automatically shut down with the operation of the system to
that space.
(b) Where natural ventilation is provided for spaces protected by a
carbon dioxide extinguishing system, provisions shall be made for easily
and effectively closing off the ventilation.
(c) Means shall be provided for closing all other openings to the
space protected from outside such space. In this respect, relatively
tight doors, shutters, or dampers shall be provided for openings in the
lower portion of the space. The construction shall be such that openings
in the upper portion of the space can be closed off either by
permanently installed means or by the use of canvas or other material
which is normally carried by the vessel.
Sec. 95.15-40 Pressure relief.
(a) Where necessary, relatively tight compartments such as
refrigeration spaces, paint lockers, etc., shall be provided with
suitable means for relieving excessive pressure accumulating within the
compartment when the carbon dioxide is injected.
Sec. 95.15-90 Installations contracted for prior to November 19, 1952.
(a) Installations contracted for prior to November 19, 1952, shall
meet the following requirements:
(1) Existing arrangements, materials, and facilities previously
approved shall be considered satisfactory so long as they meet the
minimum requirements of this paragraph and they are maintained in good
condition to the satisfaction of the Officer in Charge, Marine
Inspection. Minor repairs and alterations may be made to the same
standards as the original installation.
(2) The details of the systems shall be in general agreement with
Secs. 95.15-5 through 95.15-40 insofar as is reasonable and practicable,
with the exception of Sec. 95.15-5(d)(1), (2) and (4) covering spaces
other than cargo spaces,
[[Page 56]]
which systems may be installed in accordance with paragraphs (a) (3)
through (6) of this section.
(3) In boilerrooms, the bilges shall be protected by a system
discharging principally below the floor plates. Perforated pipe may be
used in lieu of discharge nozzles for such systems. The number of pounds
of carbon dioxide shall be equal to the gross volume of the boilerroom
taken to the top of the boilers divided by 36. In the event of an
elevated boiler room which drains to the machinery space, the system
shall be installed in the engineroom bilge and the gross volume shall be
taken to the flat on which the boilers are installed.
(4) In machinery spaces where main propulsion internal combustion
machinery is installed, the number of pounds of carbon dioxide required
shall be equal to the gross volume of the space taken to the under side
of the deck forming the hatch opening divided by 22.
(5) In miscellaneous spaces other than cargo or main machinery
spaces the number of pounds of carbon dioxide required shall be equal to
the gross volume of the space divided by 22.
(6) Branch lines to the various spaces other than cargo and similar
spaces shall be as noted in Table 95.15-90(a)(6). This table is based on
cylinders having discharge outlets and siphon tubes of \3/8\ inch
diameter.
Table 95.15-90(a)(6)
------------------------------------------------------------------------
Number of cylinders
--------------------- Nominal pipe size, inches
Over Not over
------------------------------------------------------------------------
2 \1/2\--standard.
2 4 \3/4\--standard.
4 6 1--extra heavy.
6 12 1\1/4\--extra heavy.
12 16 1\1/2\--extra heavy.
16 27 2--extra heavy.
27 39 2\1/2\--extra heavy.
39 60 3--extra heavy.
60 80 3\1/2\--extra heavy.
80 104 4--extra heavy.
104 165 5--extra heavy.
------------------------------------------------------------------------
[CGFR 65-50, 30 FR 17001, Dec. 30, 1965, as amended by USCG-1999-6216,
64 FR 53226, Oct. 1, 1999]
Subpart 95.17--Foam Extinguishing Systems, Details
Sec. 95.17-1 Application.
(a) Where a foam extinguishing system is installed, the provisions
of this subpart, with the exception of Sec. 95.17-90, shall apply to all
installations contracted for on or after November 19, 1952.
Installations contracted for prior to November 19, 1952, shall meet the
requirements of Sec. 95.17-90.
Sec. 95.17-5 Quantity of foam required.
(a) Area protected. (1) For machinery and similar spaces, the system
shall be so designed and arranged as to spread a blanket of foam over
the entire tank top or bilge of the space protected. The arrangement of
piping shall be such as to give a uniform distribution over the entire
area protected.
(2) Where an installation is made to protect an oil fired boiler
installation on a flat which is open to or can drain to the lower
engineroom or other space, both the flat and the lower space shall be
protected simultaneously. The flat shall be fitted with suitable
coamings on all openings other than deck drains to properly restrain the
oil and foam at that level. Other installations of a similar nature will
be considered in a like manner.
(3) Where a system is installed to protect a tank, it shall be so
designed and arranged as to spread a blanket of foam over the entire
liquid surface of the tank within the range of usual trim. The
arrangement of piping shall be such as to give a uniform distribution
over the entire area protected.
(b) Rate of application. (1) For spaces other than tanks, the rate
of discharge to foam outlets protecting the hazard shall be at least as
set forth in this paragraph.
(i) For chemical foam systems with stored ``A'' and ``B'' solutions,
a total of at least 1.6 gallons per minute of the two solutions shall be
discharged for each 10 square feet of area protected.
(ii) For other types of foam systems, the water rate to the dry
powder generators or air foam production equipment shall be at least 1.6
gallons per minute for each 10 square feet of area protected.
[[Page 57]]
(2) For tanks, the rate of discharge to foam outlets protecting the
hazard shall be as set forth in paragraph (b)(1) of this section, except
that the value of 1 gallon per minute shall be substituted in both cases
for the value of 1.6 gallons per minute.
(c) Supply of foam producing material. (1) There shall be provided a
quantity of foam producing material sufficient to operate the equipment
at the discharge rate specified in paragraph (b) of this section for a
period of at least 3 minutes for spaces other than tanks, and for at
least 5 minutes for tanks.
(d) Separate supply of foam agent. A separate supply of foam agent
need not be provided for each space protected. The total available
supply shall be at least sufficient for the space requiring the greatest
amount.
(e) Water supply for required pumps. Where pumps are required, the
water supply shall be from outside the space protected and shall in no
way be dependent upon power from the space protected.
Sec. 95.17-10 Controls.
(a) The foam agent, its container, and all controls and valves for
the operation of the system shall be of an approved type.
(b) The foam agent container and all controls and valves for the
operation of the system shall be outside the space protected and shall
not be located in such space as might be cut off or made inaccessible in
the event of fire in any of the spaces protected. The control space
shall be as convenient as practicable to one of the main escapes from
the spaces protected, and shall be marked as required by Sec. 97.37-13
of this subchapter. Where pumps are required, it shall not be necessary
that they be started from the control space.
(c) Complete, but simple instructions for the operation of the
system shall be located in a conspicuous place at or near the controls.
(d) The valves to the various spaces served shall be marked as
required by Sec. 97.37-10 of this subchapter.
Sec. 95.17-15 Piping.
(a) All piping, valves, and fittings shall meet the applicable
requirements of Subchapter F (Marine Engineering) of this chapter.
(b) All piping, valves, and fittings of ferrous materials shall be
protected inside and outside against corrosion unless specifically
approved otherwise by the Commandant.
(c) All piping, valves, and fittings shall be securely supported,
and where necessary, protected against injury.
(d) Drains and dirt traps shall be fitted where necessary to prevent
the accumulation of dirt or moisture.
(e) Piping shall be used for no other purpose.
Sec. 95.17-20 Discharge outlets.
(a) Discharge outlets shall be of an approved type.
Sec. 95.17-25 Additional protection required.
(a) In order that any residual fires above the floor plates may be
extinguished when a foam system is installed for the protection of
spaces other than tanks, at least 2 fire hydrants, in addition to those
required for the machinery space by Subpart 95.10, shall be installed
outside of the machinery space entrance. Such hydrants shall be fitted
with sufficient hose so that any part of the machinery space may be
reached with at least 2 streams of water, and each hose shall be
equipped with an approved combination nozzle, applicator, and self-
cleaning strainer as described in Sec. 95.10-10(i)(3).
Sec. 95.17-90 Installations contracted for prior to November 19, 1952.
(a) Installations contracted for prior to November 19, 1952, shall
meet the following requirements:
(1) Existing arrangements, materials, and facilities previously
approved shall be considered satisfactory so long as they meet the
minimum requirements of this paragraph and they are maintained in good
condition to the satisfaction of the Officer in Charge, Marine
Inspection. Minor repairs and alterations may be made to the same
standards as the original installation.
(2) The details of the systems shall be in general agreement with
Secs. 95.17-5 through 95.17-20, with the exception of Sec. 95.17-
5(a)(2), insofar as is reasonable
[[Page 58]]
and practicable. A 6-inch blanket of foam in 5 minutes for tanks and 3
minutes for other spaces will be considered as meeting the requirements
of Sec. 95.17-5.
Subpart 95.30--Automatic Sprinkler Systems, Details
Sec. 95.30-1 Application.
Automatic sprinkler systems shall comply with NFPA 13-1996.
[CGD 95-028, 62 FR 51207, Sept. 30, 1997]
Subpart 95.50--Hand Portable Fire Extinguishers and Semiportable Fire
Extinguishing Systems, Arrangements and Details
Sec. 95.50-1 Application.
(a) The provisions of this subpart, with the exception of
Sec. 95.50-90, shall apply to all vessels, other than unmanned barges
and fishing vessels, contracted for on or after November 19, 1952. Such
vessels contracted for prior to November 19, 1952, shall meet the
requirements of Sec. 95.50-90.
Sec. 95.50-5 Classification.
(a) Hand portable fire extinguishers and semiportable fire
extinguishing systems shall be classified by a combination letter and
number symbol. The letter indicating the type of fire which the unit
could be expected to extinguish, and the number indicating the relative
size of the unit.
(b) The types of fire will be designated as follows:
(1) ``A'' for fires in ordinary combustible materials where the
quenching and cooling effects of quantities of water, or solutions
containing large percentages of water, are of first importance.
(2) ``B'' for fires in flammable liquids, greases, etc., where a
blanketing effect is essential.
(3) ``C'' for fires in electrical equipment where the use of
nonconducting extinguishing agent is of first importance.
(c) The number designations for size will start with ``I'' for the
smallest to ``V'' for the largest. Sizes I and II are considered hand
portable fire extinguishers and sizes III, IV, and V are considered
semiportable fire extinguishing systems which shall be fitted with
suitable hose and nozzle or otherpracticable means so that all portions
of the space concerned may be covered. Examples of size graduations for
some of the typical hand portable and semiportable fire extinguishing
systems are set forth in Table 95.50-5(c).
Table 95.50-5(c)
----------------------------------------------------------------------------------------------------------------
Classification Soda-
-------------------------------------------------------------------------- acid Carbon Dry
and Foam, dioxide, chemical,
Type Size water, gallons pounds pounds
gallons
----------------------------------------------------------------------------------------------------------------
A......................................... II........................... 2\1/2\ 2\1/2\ ........ .........
B......................................... I............................ ....... 1\1/4\ 4 2
B......................................... II........................... ....... 2\1/2\ 15 10
B......................................... III.......................... ....... 12 35 20
B......................................... IV........................... ....... 20 50 30
B......................................... V............................ ....... 40 100 50
C......................................... I............................ ....... ....... 4 2
C......................................... II........................... ....... ....... 15 10
----------------------------------------------------------------------------------------------------------------
(d) All hand portable fire extinguishers and semiportable fire
extinguishing systems shall have permanently attached thereto a metallic
name plate giving the name of the item, the rated capacity in gallons,
quarts, or pounds, the name and address of the person or firm for whom
approved, and the identifying mark of the actual manufacturer.
(e) Vaporizing-liquid type fire extinguishers containing carbon
tetrachloride or chlorobromomethane or other toxic vaporizing liquids
shall be removed from all vessels.
Sec. 95.50-10 Location.
(a) Approved hand portable fire extinguishers and semiportable fire
extinguishing systems shall be installed in accordance with Table 95.50-
10(a). The location of the equipment shall be to the satisfaction of the
Officer in Charge, Marine Inspection. Nothing in this paragraph shall be
construed as limiting the Officer in Charge, Marine Inspection, from
requiring such additional equipment as he deems necessary for the proper
protection of the vessel.
[[Page 59]]
Table 95.50-10(a)--Hand Portable Fire Extinguisher and Semiportable Fire-
Extinguishing Systems
------------------------------------------------------------------------
Classification
Space (see Sec. 95.50- Quantity and location
5)
------------------------------------------------------------------------
Safety areas\1\
Wheelhouse or fire control room ................ None required.
Stairway and elevator ................ Do.
enclosures.
Communicating corridors........ A-II............ 1 in each main
corridor not more
than 150 feet apart.
(May be located in
stairways.)
Lifeboat embarkation and ................ None required.
lowering stations.
Radio room.....................
C-I\2\......................... 2 in vicinity of
exit.\2\.
Accommodations\1\
Staterooms, toilet spaces, ................ None required.
public spaces, offices,
lockers, isolated storerooms,
and pantries, open decks, etc.
Service spaces\1\
Galleys........................ B-II or C-II.... 1 for each 2,500
square feet or
fraction thereof
suitable for hazards
involved.
Paint and lamp rooms........... B-II............ 1 outside space in
vicinity of exit.
Accessible baggage, mail, and A-II............ 1 for each 2,500
specie rooms, and storerooms. square feet or
fraction thereof
located in vicinity
of exits, either
inside or outside
the spaces.
Carpenter shop and similar A-II............ 1 outside the space
spaces. in vicinity of exit.
Machinery spaces
Coal-fired boilers: Bunker and ................ None required.
boiler space.
Oil-fired boilers: Spaces B-II; B-V....... 2 required\3\; 1
containing oil-fired boilers, required.\4\
either main or auxiliary, or
their fuel-oil units.
Internal combustion or gas B-II............ 1 for each 1,000
turbine propelling machinery brake horsepower,
spaces. but not less than 2
nor more than 6.\5\
B-III........... 1 required.\67\
Electric propulsive motors or C-II............ 1 for each propulsion
generators of open type. motor or generator
unit.
Enclosed ventilating systems ................ None required.
for motors and generators of
electric propelling machinery.
Auxiliary spaces:
Internal combustion or gas B-II............ 1 outside the space
turbine. in vicinity of
exit.\7\
Electric emergency motors or C-II............ 1 outside the space
generators. in vicinity of
exit.\8\
Steam........................ ................ None required.
Trunks to machinery spaces..... ................ Do.
Fuel tanks..................... ................ Do.
Cargo spaces
Inaccessible during voyage, ................ Do.
including trunks and cargo
tanks.
Accessible during voyage....... ................ Do.
------------------------------------------------------------------------
\1\For motorboats, the total number of hand portable fire extinguishers
required for safety areas, accommodation spaces, and service spaces
shall be 1 B-II for motorboats of less than 50 gross tons and 2 B-II
for motor boats of 50 gross tons and over. Two B-I hand portable fire
extinguishers may be substituted for 1 B-II.
\2\For vessels on an international voyage, substitute 1 C-II in vicinity
of exit.
\3\Vessels of less than 1,000 gross tons require 1.
\4\Vessels of less than 1,000 gross tons may substitute 1 B-IV.
\5\Only 1 required for motorboats.
\6\If oil burning donkey boiler fitted in space, the B-V previously
required for the protection of the boiler may be substituted. Not
required where a fixed carbon dioxide system is installed.
\7\Not required on vessels of less than 300 gross tons if fuel has a
flashpoint higher than 110 deg. F.
\8\Not required on vessels of less than 300 gross tons.
(b) Semiportable fire extinguishing systems shall be located in the
open so as to be readily seen.
(c) If hand portable fire extinguishers are not located in the open
or behind glass so that they may be readily seen, they may be placed in
enclosures together with the fire hose, provided such enclosures are
marked as required by Sec. 97.37-15 of this subchapter.
(d) Hand portable fire extinguishers and their stations shall be
numbered in accordance with Sec. 97.37-23 of this subchapter.
(e) Hand portable or semiportable extinguishers, which are required
on their nameplates to be protected from freezing, shall not be located
where freezing temperatures may be expected.
Sec. 95.50-15 Spare charges.
(a) For all vessels other than motorboats spare charges shall be
carried for
[[Page 60]]
at least 50 percent of each size and each variety, i.e. foam, soda-acid,
carbon dioxide, etc., of hand portable fire extinguisher required by
Sec. 95.50-10(a). However, if the unit is of such variety that it cannot
be readily recharged by the vessel's personnel, one spare unit of the
same classification shall be carried in lieu of spare charges for all
such units of the same size and variety.
(b) Spare charges shall be so packaged as to minimize the hazards to
personnel while recharging the units. Acid shall be contained in a Crown
stopper type of bottle.
Sec. 95.50-20 Semiportable fire extinguishers.
(a) The frame or support of each size III, IV, and V fire
extinguisher required by Table 95.50-10(a) must be welded or otherwise
permanently attached to a bulkhead or deck.
(b) If an approved size III, IV, or V fire extinguisher has wheels
and is not required by Table 95.50-10(a), it must be securely stowed
when not in use to prevent it from rolling out of control under heavy
sea conditions.
[CGD 77-039, 44 FR 34133, June 14, 1979]
Sec. 95.50-90 Vessels contracted for prior to November 19, 1952.
(a) Vessels contracted for prior to November 19, 1952, shall meet
the following requirements:
(1) The provisions of Secs. 95.50-5 through 95.50-15 shall be met
with the exception that existing installations in safety areas and
service spaces may be maintained if in the opinion of the Officer in
Charge, Marine Inspection, they are in general agreement with the degree
of safety prescribed by Table 95.50-10(a). In such cases, minor
modifications may be made to the same standard as the original
installation: Provided, That in no case will a greater departure from
the standards of Table 95.50-10(a) be permitted than presently exists.
Subpart 95.60--Fire Axes
Sec. 95.60-1 Application.
(a) The provisions of this subpart shall apply to all vessels other
than motorboats.
Sec. 95.60-5 Number required.
(a) All vessels except barges shall carry at least the minimum
number of fire axes as set forth in Table 95.60-5(a). Nothing in this
paragraph shall be construed as limiting the Officer in Charge, Marine
Inspection, from requiring such additional fire axes as he deems
necessary for the proper protection of the vessel.
Table 95.60-5(a)
------------------------------------------------------------------------
Gross tons
-------------------------------------------------- Number of axes
Over Not over
------------------------------------------------------------------------
50 1
50 200 2
200 500 4
500 1,000 6
1,000 ....................... 8
------------------------------------------------------------------------
(b) Manned barges shall carry at least two fire axes.
Sec. 95.60-10 Location.
(a) Fire axes shall be distributed throughout the spaces available
to persons on board so as to be most readily available in the event of
emergency.
(b) If fire axes are not located in the open, or behind glass, so
that they may be readily seen, they may be placed in enclosures together
with the fire hose, provided such enclosures are marked as required by
Sec. 97.37-15 of this subchapter.
PART 96--VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT--Table of Contents
Subpart 96.01--Application
Sec.
96.01-1 General.
96.01-3 Incorporation by reference.
Subpart 96.03--Marine Engineering Systems
96.03-1 Installation and details.
Subpart 96.05--Electrical Engineering and Interior Communications
Systems
96.05-1 Installation and details.
[[Page 61]]
Subpart 96.06--Lifesaving Appliances and Arrangements
96.06-1 Installation.
Subpart 96.07--Anchors, Chains, and Hawsers
96.07-1 Application.
96.07-5 Ocean, coastwise, or Great Lakes service.
96.07-10 Lakes, bays, and sounds, or river service.
96.07-90 Vessels contracted for prior to November 19, 1952.
Subpart 96.17--Magnetic Compass and Gyrocompass
96.17-1 When required.
Subpart 96.25--Radar
96.25-1 When required.
Subpart 96.27--Sounding Equipment
96.27-1 When required.
Subpart 96.30--Protection From Refrigerants
96.30-1 Application.
96.30-5 General.
96.30-15 Self-contained breathing apparatus.
96.30-90 Vessels contracted for before November 23, 1992.
Subpart 96.35--Fireman's Outfit
96.35-1 Application.
96.35-5 General.
96.35-10 Fireman's outfit.
96.35-15 Stowage.
96.35-20 Spare charges.
96.35-90 Vessels contracted for before November 23, 1992.
Subpart 96.40--Pilot Boarding Equipment
96.40-1 Pilot boarding equipment.
Authority: 46 U.S.C. 3306; E.O. 12234, 45 FR 58801, 3 CFR, 1980
Comp., p. 277; 49 CFR 1.46.
Source: CGFR 65-50, 30 FR 17008, Dec. 30, 1965, unless otherwise
noted.