[Federal Register Volume 63, Number 151 (Thursday, August 6, 1998)]
[Notices]
[Pages 42097-42098]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 98-21071]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
[Docket No. NHTSA-98-4166]
Notice of Receipt of Petition for Decision That Nonconforming
1991-1996 Porsche 928 Passenger Cars Are Eligible for Importation
AGENCY: National Highway Traffic Safety Administration, DOT.
ACTION: Notice of receipt of petition for decision that nonconforming
1991-1996 Porsche 928 passenger cars are eligible for importation.
-----------------------------------------------------------------------
SUMMARY: This notice announces receipt by the National Highway Traffic
Safety Administration (NHTSA) of a petition for a decision that 1991-
1996 Porsche 928 passenger cars that were not originally manufactured
to comply with all applicable Federal motor vehicle safety standards
are eligible for importation into the United States because (1) they
are substantially similar to vehicles that were originally manufactured
for importation into and sale in the United States and that were
certified by their manufacturer as complying with the safety standards,
and (2) they are capable of being readily altered to conform to the
standards.
DATES: The closing date for comments on the petition is September 8,
1998.
ADDRESSES: Comments should refer to the docket number and notice
number, and be submitted to: Docket Management, Room PL-401, 400
Seventh St., SW, Washington, DC 20590. (Docket hours are from 10 am to
5 pm.)
FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle
Safety Compliance, NHTSA (202-366-5306).
SUPPLEMENTARY INFORMATION:
Background
Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not
originally manufactured to conform to all applicable Federal motor
vehicle safety standards shall be refused admission into the United
States unless NHTSA has decided that the motor vehicle is substantially
similar to a motor vehicle originally manufactured for importation into
and sale in the United States, certified under 49 U.S.C. 30115, and of
the same model year as the model of the motor vehicle to be compared,
and is capable of being readily altered to conform to all applicable
Federal motor vehicle safety standards.
Petitions for eligibility decisions may be submitted by either
manufacturers or importers who have registered with NHTSA pursuant to
49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice
in the Federal Register of each petition that it receives, and affords
interested persons an opportunity to comment on the petition. At the
close of the comment period, NHTSA decides, on the basis of the
petition and any comments that it has received, whether the vehicle is
eligible for importation. The agency then publishes this decision in
the Federal Register.
Champagne Imports of Lansdale, Pennsylvania (``Champagne'')
(Registered Importer 90-009) has petitioned NHTSA to decide whether
1991-1996 Porsche 928 passenger cars are eligible for importation into
the United States. The vehicles which Champagne believes are
substantially similar are 1991-1996 Porsche 928 passenger cars that
were manufactured for importation into, and sale in, the United States
and certified by their manufacturer as conforming to all applicable
Federal motor vehicle safety standards.
The petitioner claims that it carefully compared non-U.S. certified
1991-1996 Porsche 928 passenger cars to their U.S. certified
counterparts, and found the vehicles to be substantially similar with
respect to compliance with most Federal motor vehicle safety standards.
[[Page 42098]]
Champagne submitted information with its petition intended to
demonstrate that non-U.S. certified 1991-1996 Porsche 928 passenger
cars, as originally manufactured, conform to many Federal motor vehicle
safety standards in the same manner as their U.S. certified
counterparts, or are capable of being readily altered to conform to
those standards.
Specifically, the petitioner claims that non-U.S. certified 1991-
1996 Porsche 928 passenger cars are identical to their U.S. certified
counterparts with respect to compliance with Standards Nos. 102
Transmission Shift Lever Sequence * * *, 103 Defrosting and Defogging
Systems, 104 Windshield Wiping and Washing Systems, 105 Hydraulic Brake
Systems, 106 Brake Hoses, 109 New Pneumatic Tires, 113 Hood Latch
Systems, 116 Brake Fluid, 124 Accelerator Control Systems, 201 Occupant
Protection in Interior Impact, 202 Head Restraints, 204 Steering
Control Rearward Displacement, 205 Glazing Materials, 206 Door Locks
and Door Retention Components, 207 Seating Systems, 209 Seat Belt
Assemblies, 210 Seat Belt Assembly Anchorages, 212 Windshield
Retention, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion,
and 302 Flammability of Interior Materials.
Additionally, the petitioner states that non-U.S. certified 1991-
1996 Porsche 928 passenger cars comply with the Bumper Standard found
in 49 CFR part 581 and with the Theft Prevention Standard found in 49
CFR part 541.
Petitioner also contends that the vehicles are capable of being
readily altered to meet the following standards, in the manner
indicated:
Standard No. 101 Controls and Displays: (a) Substitution of a lens
marked ``Brake'' for a lens with a noncomplying symbol on the brake
failure indicator lamp; (b) installation of a seat belt warning lamp
that displays the appropriate symbol; (c) recalibration of the
speedometer/odometer from kilometers to miles per hour.
Standard No. 108 Lamps, Reflective Devices and Associated
Equipment: (a) Installation of U.S.-model headlamp assemblies that
incorporate headlamps with DOT markings; (b) installation of U.S.-model
front and rear sidemarker/reflector assemblies; (c) installation of
U.S.-model taillamp assemblies.
Standard No. 110 Tire Selection and Rims: Installation of a tire
information placard.
Standard No. 111 Rearview Mirror: Replacement of the passenger side
rearview mirror with a U.S.-model component.
Standard No. 114 Theft Protection: Installation of a warning buzzer
microswitch in the steering lock assembly and a warning buzzer.
Standard No. 118 Power Window Systems: Rewiring of the power window
system so that the window transport is inoperative when the ignition is
switched off.
Standard No. 208 Occupant Crash Protection: (a) Installation of a
U.S.-model seat belt in the driver's position, or a belt webbing-
actuated microswitch inside the driver's seat belt retractor; (b)
installation of an ignition switch-actuated seat belt warning lamp and
buzzer; (c) replacement of the driver's side air bag and knee bolster
in 1991 and 1992 models, and the driver's and passenger's side air bags
and knee bolsters in 1993 through 1996 models, with U.S.-model
components if the vehicle is not so equipped. The petitioner states
that the vehicles are equipped with combination lap and shoulder
restraints that adjust by means of an automatic retractor and release
by means of a single push button at both front designated seating
positions, with combination lap and shoulder restraints that release by
means of a single push button at both rear outboard designated seating
positions, and with a lap belt in the rear center designated seating
position.
Standard No. 214 Side Impact Protection: Installation of
reinforcing beams.
Standard No. 301 Fuel System Integrity: Installation of a rollover
valve in the fuel tank vent line.
The petitioner also states that a vehicle identification number
plate must be affixed to the vehicles to meet the requirements of 49
CFR part 565.
Interested persons are invited to submit comments on the petition
described above. Comments should refer to the docket number and be
submitted to: Docket Section, National Highway Traffic Safety
Administration, Room 5109, 400 Seventh Street, SW., Washington, DC
20590. It is requested but not required that 10 copies be submitted.
All comments received before the close of business on the closing
date indicated above will be considered, and will be available for
examination in the docket at the above address both before and after
that date. To the extent possible, comments filed after the closing
date will also be considered. Notice of final action on the petition
will be published in the Federal Register pursuant to the authority
indicated below.
Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8;
delegations of authority at 49 CFR 1.50 and 501.8.
Issued on: August 3, 1998.
Marilynne Jacobs,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 98-21071 Filed 8-5-98; 8:45 am]
BILLING CODE 4910-59-P