[Federal Register Volume 63, Number 165 (Wednesday, August 26, 1998)]
[Proposed Rules]
[Pages 45425-45426]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 98-22821]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 98-NM-188-AD]
RIN 2120-AA64
Airworthiness Directives; Saab Model SAAB SF340A and SAAB 340B
Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to certain Saab Model SAAB SF340A and
SAAB 340B series airplanes. This proposal would require a one-time
visual inspection of the main landing gear (MLG) brake assemblies to
determine the brake configuration, and reconfiguration, if necessary.
This proposal is prompted by issuance of mandatory continuing
airworthiness information by a foreign civil airworthiness authority.
The actions specified by the proposed AD are intended to prevent an
incorrect brake combination configuration of the MLG, and consequent
reduced controllability of the airplane during take-off and landing.
DATES: Comments must be received by September 25, 1998.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 98-NM-188-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except
Federal holidays.
The service information referenced in the proposed rule may be
obtained from Saab Aircraft AB, SAAB Aircraft Product Support, S-
581.88, Linkoping, Sweden. This information may be examined at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington.
FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-2110; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this notice may be changed in
light of the comments received.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this notice must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 98-NM-188-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 98-NM-188-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
The Luftfartsverket (LFV), which is the airworthiness authority for
Sweden, notified the FAA that an unsafe condition may exist on certain
Saab Model SAAB SF340A and SAAB 340B series airplanes. The LFV advises
that, during testing of improved brakes that were modified in
accordance with SAAB Service Bulletin 340-32-113, Revision 1, dated
February 9, 1998 (SAAB Modification 2898), the airplane handling was
unbalanced, which resulted in degraded brake performance during
landing. Investigation revealed that the unbalanced condition was due
to the installation of an incorrect combination of main landing gear
(MLG) brake assemblies. This condition, if not corrected, could result
in reduced controllability of the airplane during take-off and landing.
[[Page 45426]]
Explanation of Relevant Service Information
SAAB has issued Service Bulletin 340-32-114, dated May 4, 1998,
which describes procedures for a one-time visual inspection of the MLG
brake assemblies to determine the brake configuration, and
reconfiguration of the brake assemblies, if necessary. Accomplishment
of the actions specified in the service bulletin is intended to
adequately address the identified unsafe condition. The LFV classified
this service bulletin as mandatory and issued Swedish airworthiness
directive 1-127, dated May 5, 1998, in order to assure the continued
airworthiness of these airplanes in Sweden.
FAA's Conclusions
These airplane models are manufactured in Sweden and are type
certificated for operation in the United States under the provisions of
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and
the applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, the LFV has kept the FAA informed of
the situation described above. The FAA has examined the findings of the
LFV, reviewed all available information, and determined that AD action
is necessary for products of this type design that are certificated for
operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would require accomplishment of
the actions specified in the service bulletin described previously.
Cost Impact
The FAA estimates that 276 airplanes of U.S. registry would be
affected by this proposed AD, that it would take approximately 1 work
hour per airplane to accomplish the proposed inspection, and that the
average labor rate is $60 per work hour. Based on these figures, the
cost impact of the proposed AD on U.S. operators is estimated to be
$16,560, or $60 per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the proposed requirements of
this AD action, and that no operator would accomplish those actions in
the future if this AD were not adopted.
Regulatory Impact
The regulations proposed herein would not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this
proposal would not have sufficient federalism implications to warrant
the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
SAAB AIRCRAFT AB: Docket 98-NM-188-AD.
Applicability: Model SAAB SF340A series airplanes having serial
numbers (S/N) -004 through -159 inclusive, and SAAB 340B series
airplanes having S/N's -160 through -439 inclusive; on which SAAB
Modification 2898 (reference SAAB Service Bulletin 340-32-113, dated
November 14, 1997, or Revision 1, dated February 9, 1998) has been
accomplished; certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent an incorrect brake combination of the main landing
gear (MLG), and consequent reduced controllability of the airplane
during take-off and landing, accomplish the following:
(a) Within 2 months after the effective date of this AD, perform
a one-time visual inspection of the MLG brake assemblies to
determine the brake configuration, in accordance with Saab Service
Bulletin 340-32-114, dated May 4, 1998.
(1) If the configuration of the brake assemblies is specified in
Table 1 of the service bulletin as permissible combinations, no
further action is required by this AD.
(2) If the configuration of the brake assemblies is not
specified in Table 1 of the service bulletin as a permissible
combination, prior to further flight, reconfigure the brake
assemblies, in accordance with the service bulletin.
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116, FAA,
Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
(c) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
Note 3: The subject of this AD is addressed in Swedish
airworthiness directive 1-127, dated May 5, 1998.
Issued in Renton, Washington, on August 19, 1998.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 98-22821 Filed 8-25-98; 8:45 am]
BILLING CODE 4910-13-P